Associated Electrics, Inc. Customer Service 26021 ...petitrc.com/setup/associated/setupb4/B4.2_Manual.pdf · maintaining your new RC10 B4.2. Please take a moment to read through this

11/1

2

2:: Introduction

:: KIT Features

:: Additional

:: Other Helpful Items

Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer ServiceTel: 949.544.7500Fax: 949.544.7501

Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 B4.2. Please take a moment to read through this manual to help familiarize yourself with these steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.

Features in the B4.2 Factory Team:

• Factory Team 12mm “Big Bore” hard anodized, threaded aluminum shocks with TiN “Gold” 3mm shock shafts

• VTS slipper (variable torque, multi-plate slipper with 3 drive surfaces) and high-resolution spring

• Factory Team blue aluminum steering bellcrank set

• Factory Team 12mm blue aluminum front and rear clamping hexes with hex drive wheels

• Factory Team 7075-T6 blue aluminum 0° rear hubs with oversized outer bearing

• +8mm B4 chassis and Pro-Line Bulldog +8mm body

• Updated front and rear shock towers optimized for the 12mm ‘Big Bore’ shocks

• CVA joints with pin retainer clips

• Ball differential with light-weight outdrives

• Factory Team carbon fiber battery strap and blue aluminum thumb screws

• Complete set of precision ball bearings

• Factory Team blue titanium turnbuckles, blue aluminum hinge pin brace, milled motor plate, servo mounts, rear ballast weight and much more!

Your new B4.2 FT kit comes unassembledand requires the following items for completion (refer to catalog section for suggestions):• R/C two channel surface frequency radio system• AA-size batteries for transmitter (#302 alkaline, #303 rechargealble)• Electronic Speed Control, ESC (#29140, #29143)• Steering servo (#29166, #29167) • R/C electric motor • Pinion gear, size determined by type/wind of motor• Battery charger (a peak detection charger, or LiPo compatible charger)• 6 cell NiMH battery pack (#700) or a 2 cell LiPo battery pack (#714)

• Calipers or a precision ruler • Needle nose pliers• Lexan specific spray paint• Reamer / hole punch • Cyanacrylate glue (#1597) • Thread locking compound (#1596)• Tires and Inserts, Fronts and Rears

Tools included:• Allen wrenches #6950 (.050”, 1/16”, 3/32”, 5/64”)• Molded tools #6956• Camber gauge #1719

• Silicone Shock Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife • FT Hex Wrenches (AE Part # 1655) • Needle Nose Pliers • Multi Tool (AE Part #7494)• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)

3:: Table of Contents

:: Notes

This symbols indicates a special note or instruction in the manual.

!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.

1................... Cover

2................... Introduction 3................... Table of Contents

4................... Steering Build (Bag A-AA)

4 - 5............. Front End, Outer Build (Bag B-BB)

5 - 6............. Front End, Inner Build (Bag C)

6 - 9............. Transmission Build (Bag D-DD)

9 - 11........... Rear End Build (Bag E-EE)

11 - 12........ CVA and Turnbuckle Build (Bag F-FF)

12 - 14........ Shocks Build (Bag G-GG)

14 - 16........ Electronics Build (Bag H-HH)

16 - 17........ Wheels, Tires and Body Install (Bag I)

17................. Servo Chart

18 - 19....... Tuning Tips

20 - 29....... Catalog

30................ Notes

31................ Setup Sheet “Kit Setup”

32................ 1:1 Hardware “Fold Out”

33................ Setup Sheet “Blank”

34................ Back Cover

Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer ServiceTel: 949.544.7500Fax: 949.544.7501

:: Steering Build - Bag A-AA - Step 2

:: Front End, Outer Build - Bag B-BB - Step 1

4:: Steering Build - Bag A-AA - Step 1

Install the C Clip into the groove

shown below.

Do not overtighten steering bolts. Make sure there is free movement in the steering rack.

!

!

Build 2 (1 left, 1 right) Build 2!!

69224-40x1/2

fhcs

69154-40x5/8

fhcs

9637B4

chassis +8mm

9659Steering

brace9640

Steeringbolt(left)

6272Dust cover

foam

9659Block carrier

bushingx2

x2

x2

x2

3981Ballstud, .20 black, short

6276Ballstud, .20 silver, short

69174-40x3/8

bhcs

6272Dust cover

foam9679FT Aluminum Bellcrank Set

3971Steering rack

bearing

9566Top plate

89229Blue

countersunk washer

9563Front

bulkhead

9640Steering

bolt(right)

9659Steering

rack

x4

x3x3

x2

Be careful to not get thread lock on steering

rack bushings!

!

!

!

6272Dust cover

foam 7496B4 front axle, hex

31286FT ballstud

washer, aluminum

(2mm)

9880Steering

block, hex

6277Ballstud, .30 silver, long

39773/16x3/8bearing

9882C-clip, 3/16

44494-40x3/16aluminum

locknut

#1596

thread lock

5:: Front End, Outer Build - Bag B-BB - Step 2

:: Front End, Outer Build - Bag B-BB - Step 3

:: Front End, Inner Build - Bag C - Step 1

6272Dust cover

foam

x2

Align the C-clip onthe front axles

with the D-shape inside the

steering blocks.

!

39773/16x3/8bearing

98982-56x3/16

shcs

96452-56x1/8

bhcs

9665FT front

hinge pin brace

96452-56x1/8

bhcs

7922Spacer

989112mm aluminum clamping wheel hex, buggy front

73691/16

universalroll pin

9622Hinge pin,front outer

9621Hinge pin,front inner 9562

Front bumper

9622Hinge pin,front outer

9578B4 a-arms,

front

7922Caster block,

30°(1 left, 1 right)



locknut

x269154-40x5/8

fhcs

43342-56x5/16

bhcs

x2

6:: Front End, Inner Build - Bag C - Step 2

:: Front End, Inner Build - Bag C - Step 3

:: Transmission Build - Bag D-DD - Step 1

Front Camber Turnbuckle1.26” (32.00mm)

1.44” (36.50mm)Steering Turnbuckle

Orient the notch to the left

throughout the car. It indicates

which end has the left hand threads!

!

7230ball cup(large)

7666Drive rings

9852Ball diffoutdrives

9852Ball diffoutdrives

7666Drive rings

7230ball cup(large)

14062.00”

turnbuckle

14062.00”

turnbuckle

913114-40x7/8

bhcs

9568B4 front

shock tower

1780FT aluminum

shock bushings, standard

69244-40x3/8

shcs

6277Ballstud .30silver, long

65813/32 carbide

diff balls

7664Diff gear

52T

x2

x4x2

x12

x2

x2

x2

x2

Ball diffoutdrives

rings

31286FT ballstud

washer, aluminum

(2mm)

6272Dust cover

foam

x2

#6591diff lube

#6591diff lube

#6591diff lube

#1596

thread lock

7:: Transmission Build - Bag D-DD - Step 2



As you tighten the diff bolt, you will notice the T-nut ears moving closer to the bottom of the outdrive slot. This compresses the spring behind the T-nut. The spring should be completely com-

pressed at the same time the T-nut reaches the end of the slot. Caution! Pay close attention to the feeling when the spring is

completely compressed. Do not overtighten the bolt. When you feel the spring completely compressed, loosen the diff bolt 1/8” of a turn. Your diff should now operate smoothly with resistance

as the outdrives move in opposite directions. After you have driven the car once, re-check the diff setting.

9601Top shaft

9602Top shaft

spacer

9826Transmission case(1 left, 1 right)

3977Ball bearing

3/16x3/8

9361Idler gear

shaft

9360Idler gear

3977Ball bearing

3/16x3/8

9832Ball bearing10x16mm

6575Diff

cover

6575Locking

t-nut

6582Diff

thrust spring

#6588

black grease

x2

x2

x2

x2

6573Diff thrust

washer

65895/32 x 5/16,

unflangedbearing

65745/64 diff

thrust balls

6573Diff thrust

bolt

x2

x2

x6




x2

7485FT V2

slipper hub

91177VTS

slipper pads

9603Slipper

pad

965181T 48Pspur gear

91176VTS slipper

housing

91178VTS slipper

plate91179

VTS slipper hub, outer

#1596thread lock

#1596

thread lock

69194-40x5/16

bhcs

69254-40x1/2

shcs

69134-40x1 1/4

shcs

1770FT milled

motor plate(blue)

69284-40x1

shcs

9587Wing mounts

(1 left, 1 right)

9819Motor guard

9630.030 ballstud

washer

x2

x3

x2

x3

There’s also a 75T 48P Spur Gear

(#9650)included for stock

motors use!!

!

!


:: Rear End Build - Bag E-EE - Step 1


Set nut flush with top shaft.

See page 18 for gear mesh, and slipper clutch

setting instructions!

!

!!

7487Anti-squat shim

(2 degrees)

9621Hinge pin, rear inner

9582Rear B4 a-arms (1 left, 1 right)

96452-56x1/8

bhcs

66295-40

locknut

9739Slipper spring

9818Rear chassis

plate

7487Rear arm

mount(3.0 degree)

7486V2 slipper

washer

x2

x2

x2

Compress spring first.

!

92695-40x1/2

fhcs

92695-40x1/2

fhcs

x2 x4

10:: Rear End Build - Bag E-EE - Step 3



6277Ballstud .30silver, long

96445-40x9/16

shcs74134-40x3/4

bhcs

9564Rear chassis

brace

96435-40x7/16

shcs

96435-40x7/16

shcs

69224-40x1/2

fhcs

7488Rear ballast

weight

31286FT ballstud

washer, aluminum

(1mm)

x2

x2

x2

x2

x2

x2

x2

6272Dust cover

foam

1781FT aluminum

shock bushing, short

x2

x2

#1596thread lock

Use inside hole in chassis brace!

!

11:: Rear End Build - Bag E-EE - Step 6

:: CVA and Turnbuckles Build - Bag F-FF - Step 1


Build x2 (right and left side)

1 drop!CA glue not

included

Align the gap in the pin retainer

to be opposite of the CVA pin.

!

#1597ca glue

Build x2

39773/16x3/8bearing

9864FT aluminum

hub ( 0˚)


locknut

6272Dust cover

foam

7933Crush tube

3981Ballstud, .20black, short

9917Aluminum

hub A, carbon

7935.187x.196bearing

73683/16 axle

shim

Left Side

7381CVA coupler

7996CVA pinretainer

9755CVA axle

rear

9672CVA bone

7381CVA cross

pin

#6588

black grease

62884-40x1/4

bhcs

x2

69244-40x3/8

shcs69154-40x5/8

fhcs

x2

x2

12:: CVA and Turnbuckles Build - Bag F-FF - Step 3


:: Shocks Build - Bag G-GG - Step 1

73691/16

roll pins

989012mm aluminumclamping wheel hex, buggy rear




1/16roll pins

12mm aluminumclamping wheel hex, buggy rear

Orient the notch to the left

throughout the car. It indicates

which end has the left hand threads!

!

9130812mm shock

piston (1.6 front)(1.6 rear)

9130521x3 TiN

shock shaft (front)

9130627.5x3 TiN shock shaft

(rear)

62991/8 E-clip

62991/8 E-clip

4187Nylon spacer,

(.030)

Racers Tip:

Use a marker over the numbers on the pistons to

make them easily visible!

!

Front:3 spacers

Rear:2 spacers

98982-56x3/16

shcs9645

2-56x1/8bhcs

31286FT ballstud

washer, aluminum

(1mm)

9622Hinge pin,rear outer

9630.030 ballstud

washer

Rear Camber Turnbuckle1.28” (32.25mm)

7230ball cup(large)

14062.00”

turnbuckle

x2

13:: Shocks Build - Bag G-GG - Step 2



1777FT shock pivot ball

1777Shock eyelet

#1105green slime

9129912x23mm

shock bodies (front)

9130112x31mm

shock bodies (rear)

91309Shock hat bushing

91309Shock spacer

5407O-ring

31327VCS3 shock bottom cap

31327VCS3 shock bottom cap

o-ring

9130912mm shock cap o-ring

x2

x2

#1105green slime

Racers Tip:

Lightly rub shock oil on the o-ring before installation!

Racers Tip:

Coating the o-rings with green slime

(#1105) helps seal & reduce o-ring

swell! Green slime not included in kit!

!

!

x49130312mm

shock cap

Step 9-10Step 8Step 6-7Step 4-5

Front Shock: 30 wt

Rear Shock: 30 wt

Step 2-3

31510M2x4mm

bhcs

91309Shock cap

o-ring

x4

x4Shock Bleeding Steps:1. Before assembly, get each bleed

screw and thread it 1-2 turns into the shock cap. This will make installation easier when you are bleeding your shocks.

2. Pull shock shaft down.3. Fill shock body 3/4 full with silicone

shock fluid.4. Slowly move the shock shaft up and

down to remove air from under the piston.

5. Wait for bubbles to come to surface.6. Fill shock body to top with silicone

shock fluid.7. Place a drop of oil in the cap and on

cap threads.8. Install cap (without bleed screw) and

tighten completely.9. Slowly compress shaft all the way to

bleed excess silicone shock fluid out the hole in the cap (use rag around-shock to catch excess fluid).

10. Install M2x4mm button head screw until snug while shaft is fully com-pressed.

Shock oil#5422Sh

ock oil

#5422

x4x4

9131012mm shock spring cup

(5mm offset)

9132612mm front spring, Black

(3.00lb)

9133712mm rear

spring, white (2.10lb)

9130412mm

threaded collar

9130412mm

threaded collar o-ring

x4

x4Front: 4mm

Rear: 7mm

Build x2 front and x2 rear shocks

Racers Tip:

Use your finger to rub shock oil on the o-ring for

smoother adjustment!

!

!

!

14:: Shocks Build - Bag G-GG - Step 5

:: Electronics Build - Bag H-HH - Step 1


Offset the servo horn by 5-10 degrees

(approximately one notch)! (approximately one notch)!

Use outside hole in

front arm!

!Use outside

hole in front arm!

!

Offset the servo horn by 5-10 degrees

(approximately one notch)(approximately one notch)

9170Servo link

7337Gold

washer

89007Servo horn

ring


6272Dust cover

foam

9180Servohorn

1779FT Servo mount

x4

x2

x2x2

x2

7336Servo

spacers

69174-40x3/8

bhcs

62924-40x3/8

fhcs

Servo not included!

Servo screwnot included!

6472Shock

mount nut

x2

69254-40x1/2

shcs

x2

Use inside hole in

rear arm!

!

69274-40x3/4

shcs

x2

6472Shock

mount nut

x2

Leave a 2mm gap!

!

See page 17 for correct servo spacing on the

servo chart!!

15:: Electronics Build - Bag H-HH - Step 3



6338Antenna

tube & cap

38625-40x1/8set screw

Receiver / Servo tapenot included!

ESC/ Servo tapenot included!

Pinion / Setscrewnot included!

Motor not included!

7461Gear cover

(clear)

7461Gear cover

button

6936Washer #4aluminum

62854-40x1/4

shcs

31532M3x8mm

bhcs

x2

x2

x2

See page 18 for gear mesh setting

instructions!!

16:: Electronics Build - Bag H-HH - Step 6

:: Wheels / Tires and Body - Bag I - Step 2


69538-32

LP steellocknut

x2

Tires / Insertsnot included!

Tires / Insertsnot included!

#1597

ca glue #1597

ca glue

x29696Buggy rear wheel hex,

yellow

9638B4+8mm

battery strap, carbon

9691Buggy front wheel hex,

yellow

x2

Carefully apply tire adhesive to the tire bead on

both sides.Do one side at a time, allow it to

dry before gluing the other side!

!

x269528-32

locknut, steel

17874-40x1/2set screw

1787FT battery

strap thumb screws

9238Foam

battery spacer

x2x2 x2

x2

Batterynot included!

17:: Wheels / Tires and Body - Bag I - Step 3


:: Servo Chart

Painting Tips:Body : Your B4.2 FT comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush) the paint to the inside of the body (prefferably dark colors first, lighter colors last).

NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don’t, you candestroy the plastic body!!!!).

After painting, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna!

Steering Servo ChartAssociated

* Not all servo’s are listed* Make sure servo linkage clears the servo through full travel in both directions. Use #7336 servo spacers to adjust the servos position (to make the steering link as straight as possible)

XP-1015, XP-1313 F

F

F

A

A

H

H

J

J

J

# 9180servo arm

94102

HS-5625MG, HS-5645MG, HS645MG

Z4750, Z2750

Z250, Z550

S9204, S9250, S9450

S9404

94257, 94258, 94357, 94358, 94452, 94453, 94755

HS-965, HS-985MG, HS-5965, HS-5985MG

PS-401, PS-2001, PS-2004, PS-2015, PS-2173, PS-2174, PS-2123, PS-2143, PS-2144

Airtronics

Airtronics

Hitec

Hitec

JR

JR

Futaba

Futaba

KO

x29587Wing shims

69294-40x3/8

shcs(w/hole)

x26332Body clips

*Racers Tip:Instead of using the included body clips (#6332) and the #6929 SHCS for the top

plate to install your body, you can use hook and loop tape

on the inside of the body, and the sides of the chassis to

keep your body in place!

!

18:: Tuning TipsTips for Beginners:

Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.

Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.

When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions.

Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without binding to prevent poor and/or inconsistent handling.

Motor Maintenance:

Brushed motors require frequent maintenance to keep performance levels at their maximum. Between runs and after letting the motor cool completely, inspect the brushes to ensure that they are moving freely in their holders. Remove the springs and slide the brushes in and out of their holders checking for any resistance or rough spots. If found, remove the brush and carefully wipe it clean. Removing buildup will allow the brush to slide freely and create maximum contact with the commutator resulting in maximum power output.After every 3-5 runs, remove the brushes from their holders and inspect the tips for wear or burning. If there is noticeable wear (less than 75% of the brush remaining), it is best to cut the commutator and replace the brushes with a new pair. If the tips become a burned blue color, the lubricant in the brush has been burned away and new brushes should be installed.Occasionally, the motor should be cleaned with a soft brush to prevent dirt build up around the brush hood area and ball bearings. At this time, it is a good idea to add one drop of bushing / bearing oil to each bushing or ball bearing.

If using a brushless motor, please refer to the motor manufacturer’s guidelines for proper maintenance.

Slipper Clutch:

The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.

Motor Gearing:

Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information. Team Associated is not responsible for motor damage due to improper gearing. * These gearings are for use with advanced timing speed control settings!

Set The Gear Mesh:

You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again. A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.

27T Reedy Stock19T Reedy Super Stock

17.5 Reedy Sonic Brushless *17.5 Reedy Sonic Brushless

13.5 Reedy Sonic Brushless *13.5 Reedy Sonic Brushless10.5 Reedy Sonic Brushless9.5 Reedy Sonic Brushless8.5 Reedy Sonic Brushless7.5 Reedy Sonic Brushless6.5 Reedy Sonic Brushless

3300kV Brushless3900kV Brushless4900kV Brushless6100kV Brushless

232223322230242322212121211918

818178758175818181818181818181

9.16:19.57:18.82:16.09:19.57:16.50:18.78:19.15:19.57:1

10.03:110.03:110.03:110.03:111.08:111.70:1

Motor Pinion Spur FDRB4.2 Gear Ratio Chart (Internal Gear Ratio 2.60:1)

19:: Tuning Tips (cont.)Front Camber Links:

Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Longer camber links are typically used on high grip tracks and shorter links tend to work better on medium-grip loose tracks.

*Raise or lower the ball end by adding

or subtracting washers here

!

Caster:

Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin leans rearward at the top. The supplied 30° caster blocks (#7922) are recommended in most cases. For less corner entry steering and more exit steering, try the optional 25° blocks (#7919).

Rear Camber Link:

Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the rear chassis brace. Shortening the camber link (or lowering the ball end) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ball end) will give the rear more roll and more cornering grip. Longer camber links are typically used on high grip tracks, while shorter links tend to work better on medium grip loose tracks. The kit setting is the best compromise of cornering grip and acceleration.

Wheelbase Adjustment:

You have three options for rear hub spacing, Forward, Middle, & Back. The kit setting provides the most rear traction, and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to the Middle or Back position. This can also make the car handle better in 180° turns.

Rear Camber:

Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.

Anti-Roll Bars:

The optional #9635 rear anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks (try the gold bar). The silver and black anti-roll bars are typically used on medium-grip loose tracks.

Ride Height:

Ride height is the distance from the ground to the bottom of the chassis.The standard front ride height setting is with the front arms level (reffered to as “arms level”) or 24mm (Ride Height Gauge #1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right arms appear to be level.

The rear ride height setting you should use most often is with the outdrive, driveshaft, and axles all on the same imaginary horizontal line (reffered to as “bones level”) or 24mm (Ride Height Gauge#1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right driveshafts appear to be level.

Front Camber:

Camber describes the angle at which the tire and wheel rides when looked at from the front. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Positive camber, where the top of the tire is leaning out, is not recommended.

*Testing camber with camber gauge

!

*Raise or lower the ball end by

adding or subtracting

washers here

*Spacers to the rear will place hubs for-ward, shortening the wheelbase

*Front arms should be in a straight line when ride height is set at “arms level”

*CVA bones should be in a straight line when ride height is set at “CVA bones

level”

!

!

!

!

*Spacers to the rear

20:: Shocks

:: Shock Springs

:: Ball Differential

:: Shock Oil

177741875407629931327315109129991301913039130491305913069130891309913109131491316

4 ea.12812

2 ea.6222211

4 ea.1

4 ea.22

913259132691327913289132991330913319133291333913349133591336913379133891339913409134191342913439134491345

Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.11111

5420542154225423542454255426542754285429543054315432543354345435543654375438

2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.

65736574657565816582658976647666767798529853

261

121212111

FT Blue Aluminum Shock Pivot Ball with Eyelet.030 Nylon WasherRed O-RingsE-ClipVCS3 Shock Bottom Cap and O-RingM2 x 4mm BHCS12X23mm FT Shock Bodies (front)12X31mm FT Shock Bodies (rear)12MM Shock Cap12MM Threaded Collar and O-Ring21X3mm TiN Shock Shaft (front)27.5X3mm TiN Shock Shaft (rear)12MM Shock Pistons, (1.5, 1.6, 1.7)12MM Shock Rebuild Kit12MM Shock Spring Cups (+0mm, +5mm, +9mm)12MM Shock (B4/B44 Front)12MM Shock (B4/B44 Rear)

12MM Front SPRING BRN 2.8512MM Front SPRING BLK 3.00 - Kit12MM Front SPRING GRN 3.1512MM Front SPRING WHT 3.3012MM Front SPRING GRY 3.4512MM Front SPRING BLU 3.6012MM Front SPRING YLW 3.7512MM Front SPRING RED 3.9012MM Front SPRING ORN 4.0512MM Front SPRING PRL 4.2012MM Rear SPRING BLK 1.9012MM Rear SPRING GRN 2.0012MM Rear SPRING WHT 2.10 - Kit12MM Rear SPRING GRY 2.2012MM Rear SPRING BLU 2.3012MM Rear SPRING YLW 2.4012mm Big Bore Front Soft Spring Kit12mm Big Bore Front Medium Spring Kit12mm Big Bore Front Hard Spring Kit12mm Big Bore Rear Soft Spring Kit12mm Big Bore Rear Medium Spring Kit

10 Weight Silicone Shock Oil20 Weight Silicone Shock Oil30 Weight Silicone Shock Oil40 Weight Silicone Shock Oil22.5 Weight Silicone Shock Oil80 Weight Silicone Shock Oil27.5 Weight Silicone Shock Oil15 Weight Silicone Shock Oil25 Weight Silicone Shock Oil35 Weight Silicone Shock Oil45 Weight Silicone Shock Oil55 Weight Silicone Shock Oil32.5 Weight Silicone Shock Oil37.5 Weight Silicone Shock Oil42.5 Weight Silicone Shock Oil50 Weight Silicone Shock Oil60 Weight Silicone Shock Oil70 Weight Silicone Shock Oil47.5 Weight Silicone Shock Oil

Diff Thrust Washer & BoltPrecision Diff Thrust Balls, 5/64”Locking T-Nut, Diff Thrust Bolt, & Cover3/32” Carbide Diff BallsDiff Thrust SpringBall Bearing, 5/32 x 5/16” unflangedDiff Gear 52TDiff Drive Rings, 2.60:1B4 / T4 / GT Diff Rebuild KitSC10 Ball Diff OutdrivesSC10 Complete Ball Differential

6299

6299

91304

91304

91310

31327

31327

5407

5407

91303

91309

91309

91309

31510

9130591306

9129991301

4187

1777

1777

91308

6575

9853

6582

9852

7666

6589

6581

7664

6589

7666

9852

6573

6573

6574

6575

6575

21:: Slipper Clutch

:: Optional Gear Differential

:: Differential Fluids

6285662974617485748696039649965096519652965397399117591176911779117891179

126121211111111211

982798289829983098319888

5450545154525453545454555456545754585459

111

Pr.12

1111111111

Complete Gear DiffDiff Gear and Cover SetGear Diff Rebuild KitGear Diff OutdrivesGear Diff O-Ring Set0.5mm Gear Diff Shim

Silicone Diff Fluid 1,000CSTSilicone Diff Fluid 2,000CSTSilicone Diff Fluid 3,000CSTSilicone Diff Fluid 5,000CSTSilicone Diff Fluid 7,000CSTSilicone Diff Fluid 10,000CSTSilicone Diff Fluid 20,000CSTSilicone Diff Fluid 30,000CSTSilicone Diff Fluid 60,000CSTSilicone Diff Fluid 100,000CST

4-40 x 1/4” SHCS5-40 Diff Locking NutMolded Gear Cover, ClearFT V2 Slipper HubsFT V2 Slipper Spring and WasherSlipper Pad72T 48P Spur Gear75T 48P Spur Gear81T 48P Spur Gear (Kit)78T 48P Spur Gear84T 48P Spur GearSlipper SpringFT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outer

7486

97396629

7485

7461

6285 6285

7461

91179

91176

91177

91177

91178

9603

9651

:: Turnbuckles and Servo Mounts1406177939816272629269177230733673379170918089007

226

2866

1214111

FT Blue Titanium Turnbuckles, 2.00”FT Servo Mount, blueBallstud .20” Black, shortFoam Ballend Dust Covers4-40 x 3/8” FHCS4-40 x 3/8” BHCSBallups, LargeSteering Servo Mount Kit.250 x .125 x .015” WasherSteering Servo LinkServo Horns, MoldedSteering Servo Ring, blue

91709180

1779

17796292

6917

6917

6917

6917

73367337

7337

7336

6292

39816272

9170

9170

89007

9830

9828

9828

9828

9828

9888

9829

9829

9888

9829

9829

7230

1406

9829

9829

9831

9831

9831

9831

9831

9830

9830

9830

:: Front Bulkhead / Steering

:: Front Shock Tower

:: Rear Shock Tower

39713981627262766332691769226929956696409659

967989229

17806272627764726924956831286

91311

4284461

4ea

6

178163326472691574139572958796439644

464661166

FT Shock Bushing, standard (blue)Foam Ballend Dust CoversBallstud .30 Silver (short)4-40/5-40 Plastic Nut4-40 x 3/8” SHCSB4 Front Shock TowerFT Ballstud Washer, aluminum(1mm, 2mm)4-40 x 7/8 BHCS

FT Shock Bushings, short, (blue)Body Clips4-40/5-40 Plastic Nut4-40 x 5/8” FHCS4-40 x 3/4 BHCSB4 Rear Shock TowerB4 / T4 Wing Mount / Shim Set5-40 x 7/16” SHCS 5-40 x 9/16” SHCS

.125 x .250 x .109“ BearingsBallstud .20 Black, shortFoam Ball end Dust CoversBallstud .20” Silver (short)Body Clip, Large4-40 X 3/8” BHCS4-40 x 1/2” FHCS4-40 x 3/8” SHCS w/holeB4 / T4 Top PlateB4 / T4 Steering Bolt, left & rightB4 / T4 Steering Set. Includes Rack,Bellcrank, Servo Saver, Steering BraceB4/T4 Aluminum Bellcrank SetBlue Countersunk Washers

22

9566

69226922

6922

89229

6332

6332

6332

6332

6929 6272

6272

91311

913119568

6277

6277

31286

31286

6924

6924

6924

6924

1780

1780

1781

1781

6472

6472

6472

6472

9587

95879587

9587

9572

9643

9643

9644

9644

7413

6915

6915

7413

6272

6272

6272

9640

9640

9659

3971

3971

3971 3971

6276

9679

9679

9659

3981

3981

9659

6917

6917

89229

89229

46

2866664111

110

23 :: Front Arm

:: Rear Arm

39773983444962726277692569537369749679229578962196229645988098829891

989831286

265

28466421

Pr.118

Pr.62

64ea

39773981627262886925695273687369738179337935958296229630964596729677975598649890

989899173123731286

26

28666

144122

Pr.1

10821222

622

4ea

Ball Bearing 3/16” x 3/8”Ballstud .30” Black (short)4-40 x 3/16 Aluminum LocknutFoam Ballend Dust CoversBallstud .30 Silver (short)4-40 X 1/2” SHCS8-32 Low Profile Locknut, steel1/16” Universal Roll PinsB4 Front Axle, hexCaster Block, (left & right) 30 degFront A-Arm B4Inner Hinge Pin SetOuter Hinge Pin Set2-56 x 1/8” BHCSSteering Block, Hex C-Clip, 3/16”12mm Aluminum Clamping Wheel Hex, Buggy Front2-56 x 3/16 SHCSFT Ballstud Washer, aluminum(1mm, 2mm)

Ball Bearing 3/16 x 3/8”Ballstud .20” Black (short)Foam Ballend Dust Cover4-40 X 1/4” BHCS4-40 x 1/2” SHCS8-32 Locking Nut, Steel3/16” Axle Shims1/16” Axle Roll PinsCVD Rebuild KitAxle Spacer Crush TubesBearing, .187 x .50 x .196B4 Rear A-Arms (left & right)B4 Outer Hinge Pin SetBallstud Washer2-56 x 1/8” BHCSFT CVA Bone, B4FT CVA Set, B4CVA Axle, RearFT Aluminum Hub, 0.0 deg12mm Aluminum Clamping Wheel Hex, Buggy Rear2-56 x 3/16 SHCSFT Aluminum Hub A, carbonCVA Pin Retaining ClipAluminum Ballstud Washer(1mm & 2mm)

79227922

9622

9622

9622

9621

9645

9645

9645

9645

6925

6925

9582

9578

7496

9882

6272

6272

6272

3981

6277

31286

9880

31286

3977 3977

3977

96306288

9917

7933

7935 7369

6952

9890

9898

9864

6953

9898

9891

7369

3983

4449

4449

4449

97557368

7381

7381

9672

31237

24:: Battery Strap

:: Transmission

178792389638

111

1770397769136919692269246925692869369360936195759601960296309826983231532

12666666101111110126

FT Battery Strap Thumbscrews SetFoam Battery Spacers, SetBattery Strap B4, Carbon Fiber

FT Milled Motor Plate, blueBall Bearing, 3/16” x 3/8“4-40 x 1 1/4” SHCS4-40 X 5/16” BHCS4-40 X 1/2” FHCS4-40 X 3/8” SHCS4-40 x 1/2” SHCS4-40 x 1” SHCS#4 Washer, aluminumIdler Gear, moldedIdler Gear ShaftRear Motor GuardB4/T4 Top ShaftB4/T4 Top Shaft SpacerBallstud WasherTransmission Case for Gear Diff (left & right)Ball Bearing, 10 x 16mmM3 x 8mm BHCS

:: Pinion Gears8253825482558256825782588259826082618263826482658266826782688269827082718272

1111111111111111111

16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear 26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear33T 48P Pinion Gear34T 48P Pinion Gear35T 48P Pinion Gear

1787

1787

1787

1787

9638

9238

69196919

9575

69226922

6924

9832

9832

9361

9602

9601

9360

3977

39779826

9826

6925 6928

6928

6913

9630

9630

9630

1770

6924

31532

31532 6936

6936

9238

25:: Chassis

38624334627262776338691574877488926995629563956496219637964396459665981831286

68

28416116111416811

4ea

5-40 x 1/8” Set Screw2-56 x 5/16” BHCSFoam Ballend Dust CoverBallstud .30” Silver (long)Antenna Tube & Cap (black)4-40 X 5/8” FHCSArm Mounts 2.5, 3, 3.5, 4 deg SetBallast Weight5-40 x 1/2” FHCSFront BumperB4 / T4 / GT2 Front BulkheadRR / FR Hinge BraceB4 Inner Hinge Pin SetB4 +8mm Chassis5-40 x 7/16” SHCS 2-56 x 1/8” BHCSFT Hinge Pin Brace, blueB4/T4/SC10 Arm Mount / Chassis PlateAluminum Ballstud Washer(1mm & 2mm)

:: Wheels9690969196959696

2222

Buggy Front Wheel, hex, whiteBuggy Front Wheel, hex, yellowBuggy Rear Wheel Hex, whiteBuggy Rear Wheel Hex, yellow

3862

6338

9818

9645

9621

9621

7487

7487

7488

9269 9269

9637

69156915

6915

6915

9562

9563

4334

9665

6272

6272

9564

31286

6277

6277

31286

9643

9643

96969691

Not includedin Kit!

Not includedin Kit!

26:: Factory Team and Option Parts140614091585165417341735173617701777177817791780178117873971690669376943738174857486748779227990956195659567956995739577957995839586959295939594959795989599

9600B96239635

9655966596729673967796799739975597899795979697979798979998649865986698679872991731237312869117591176911779117891179

Pr.Pr.Pr.41046141

Pr.44

Pr.42661

Pr.11

Pr.111111

Pr.Pr.Pr.1

Pr.Pr.1

Pr.Pr.11

Pr.1

11

Pr.Pr.Pr.11

Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.1

Pr.Pr.

4ea.11211

FT Ti Turnbuckle, 2.00” (blue)FT Ti Turnbuckle, 1” (sway bar) (blue)FT B4 Aluminum Trailing AxleFT Solid Axle PinsFT Blue Body Clip, 4 long, 6 shortFT Blue Body Clip, longFT Blue Body Clip, shortFT Milled Aluminum Motor Plate, (blue)Blue Aluminum Shock Ball Ends with EyeletsFT Milled Aluminum Motor Plate, (black)FT Servo Mounts, blue aluminumFT Blue Alum. Threaded Shock Bushings (standard)FT Blue Alum. Threaded Shock Bushings (short)FT Battery Strap Thumb ScrewsSteering Rack BearingsBall Bearing, PTFE Sealed 3/16 x 3/8”FT 4-40 Aluminum Locknuts (blue)FT 8-32 Aluminum Locknuts (blue)CVD Rebuild KitFT V2 Slipper HubsFT V2 Slipper Spring and WasherArm Mount Set (2.5, 3, 3.5, 4 deg)Caster Block 30 deg, (left & right)Aluminum Front BulkheadB4 Chassis Carbon, short chassisChassis Brace, Hinge Pin Brace, CarbonTop Plate, CarbonFront Shock Tower B4 CarbonRear Shock Tower Carbon B4Steering Blocks, Inline (B4 req. #9623)Front A-Arm B4 CarbonRear A-Arm B4 CarbonBattery Strap Carbon, B4 (short chassis)Caster Block 20 deg, (left & right)FT Caster Block, 30 deg, (left & right)Battery Strap Woven Carbon, B4 (short chassis)CVD Axle Bones, B4CVD Axles, B4 / T4CVD Set, B4FT Aluminum Motor Plate (blue)FT B4 Front Inline Axle (req. #9577)B4 / T4 Sway Bar Kit. Includes color coded bars,soft (black), med (silver), hard (gold)B4 Full Carbon Set, (short chassis)FT B4 / T4 Aluminum Hinge Pin BraceFT CVA Bone, B4B4 Shiny CVD DogboneFT CVA Set, B4B4/T4 Aluminum Bellcrank SetSlipper SpringCVA Axle, Rear (B44, B4, T4, SC10)FT Titanium Front Axles, SC10 / B4Ti Nitride Ballstuds 4-40 x 0.20” LongTi Nitride Ballstuds 4-40 x 0.30” LongTi Nitride Ballstuds 4-40 x 0.40” LongTi Nitride Ballstuds 4-40 x 0.20” ShortTi Nitride Ballstuds 4-40 x 0.30” ShortFT Aluminum Hub, 0 degFT Aluminum Hub, 0.5 degFT Aluminum Hub, 1 degFT Aluminum Hub, 1.5 degFT Aluminum Hub Tower SetAluminum Hub A, CarbonCVA Pin Retaining ClipFT Ballstud Washer, aluminum (1mm, 2mm)FT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outer

:: Body and Decals

:: XP Electronics

:: Reedy Accessories

9614965896759676969297729790979197929782

291072912529126291412914229143291662916729209292102921129212292142921529216292172921829221

1111111111

111111111111111111

604605606607654655656658659660661663664716959960961962972973974975978979980981982992

1111111111111111111111111111

B4 Clear Body & WingB4 Decal SheetB4 Painted Body, Flames, Blue BackgrouondB4 Painted Body, Flames, Red BackgroundB4 Vortex Body + Wings Set, clearHigh Downforce Wing 6.5”B4.1 RTR Body, Blue, with spoiler (Kit, B4.1)B4.1 RTR Body, Green, with spoiler (Kit, B4.1)B4.1 Body Clear, with spoilerB4.2 Decal Sheet

S1903 Metal Gear SetS1903MG ServoS2008MG ServoXP SC450-BL Brushless ESCXP ESC Fan OptionXP SC700-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313 / DS1015Accessory Pack, DS1313 / DS1015TRS 403-SSi ReceiverXP2G 2.4GHz Radio SystemXP3G 2.4GHz Radio SystemXP TRS402-SSI ReceiverXP2-SSi 2.4GHz Radio SystemXP3SS 2.4GHz Radio System

526-S AC/DC 2S-6S LiPo/LiFe ChargerMotor Cooling Fans (2)Charge Harness 2S Saddle Pack 4mmCharge Harness 2S Standard Pack 4mm4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (10M)4.0mm plugs (30M)3.5mm plugs (3M, 3F)3.5mm plugs (10F)3.5mm plugs (10M)3.5mm plugs (30M)Reedy 09 Decal SetSonic 540/550 Sensor w/BearingSonic 540/550 Insulator Set (2 pcs.)Sonic 540/550 Timing Cap w/ScrewsSonic 540 Case Screws (3 pcs.)Sonic 540 Steel Bearing SetSonic 540 Ceramic Bearing Set540-SL/550-SL Steel Bearing Set540-SL/550-SL Ceramic Bearing SetFlat Sensor Wire 70mmFlat Sensor Wire 110mmFlat Sensor Wire 150mmFlat Sensor Wire 200mmFlat Sensor Wire 270mmSonic 540 Rotor Spacers

:: Reedy Motors and ESC’s

:: Reedy Batteries

908920921922923940941941S942943944945946947948949950951952954955956957958987

1111111111111111111111111

302303309601602628632633634637736738

111111111111

Replacement Rotor 540-SL540-SL Brushless Motor 3300kV540-SL Brushless Motor 3900kV540-SL Brushless Motor 4900kV540-SL Brushless Motor 6100kVSonic 540 21.5 Competition Brushless MotorSonic 540 17.5 Competition Brushless MotorSonic 540 17.5 Replacement StatorSonic 540 13.5 Competition Brushless MotorSonic 540 10.5 Competition Brushless MotorSonic 540 9.5 Competition Brushless MotorSonic 540 8.5 Competition Brushless MotorSonic 540 7.5 Competition Brushless MotorSonic 540 6.5 Competition Brushless MotorSonic 540 5.5 Competition Brushless MotorSonic 540 5.0 Competition Brushless MotorSonic 540 4.5 Competition Brushless MotorSonic 540 4.0 Competition Brushless MotorSonic 540 3.5 Competition Brushless MotorSonic 540 Stock Rotor 12.3 x 24.2 (7.25)Sonic 540 Stock Rotor 12.3 x 25.0 (7.25)Sonic 540 Stock Rotor 12.5 x 25.0 (7.25)Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)Sonic 540 Modified Rotor 13.0 x 25.3 (5.0)

AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable 7000mAh 65C 7.4v LiPo6500mAh 65C Competition 7.4V LiPo4100mAh 65C Competition 7.4V Shorty LiPo5500mAh 7.4V 60C LiPoTX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VWolfPack 5000mAh 25C 7.4V LiPoWolfPack 3800mAh Shorty 7.4V 25C

27

:: LRP Speed ControlsLRP80230LRP80250LRP80970

111

Spin Super BrushlessSpin Pro BrushlessFlow Works Team

:: LRP Chargers, Power Supply, BalancerLRP41281LRP41555LRP42103LRP42104LRP42105LRP42305LRP42306LRP43200LRP45050LRP45200LRP65800LRP65802LRP65803LRP65804LRP81801

111111111111111

Quadra Pro 2 ChargerPulsar Touch Competition ChargerLiPo Balance Board XHLiPo Balance Board FP/TP LiPo Balance Board PQPulsar Touch Temperature SensorPulsar Touch Sensor Wire SplitterLRP Competition 20A Power SupplyLRP 2in1 LiPo Guard + BECLiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mmSoldering Tip 1.2mmSoldering HandleLRP Speedo Updater Spec 2

:: LRP Brushless Motors / CombosLRP50430LRP50440LRP50450LRP50460LRP50480LRP50643LRP50644LRP50654LRP50664LRP50674LRP50684LRP50689LRP50694LRP50704LRP80741LRP80742LRP80743

11111111111111111

Vector K4 6.5 TurnVector K4 8.5 TurnVector K4 10.5 TurnVector K4 13.5 TurnVector K4 17.5 TurnVector X-20 10.5 TurnVector X-20 9.5 TurnVector X-20 8.5 TurnVector X-20 7.5 TurnVector X-20 6.5 TurnVector X-20 5.5 TurnVector X-20 5.0 TurnVector X-20 4.5 TurnVector X-20 4.0 TurnSpin Super / K4 17.5 Turn Spin Super / K4 13.5 TurnSpin Super / K4 10.5 Turn

:: LRP Misc.LRP50621LRP50622LRP50623 LRP50626LRP50632 LRP50634LRP50635LRP50636LRP50637LRP50638LRP50639LRP62415LRP80135LRP82512LRP82515LRP82520LRP82530LRP82531LRP819307LRP819310LRP819315LRP819320

1111111111111111111111

X-12 Optional Ceramic Ball BearingsX-12 Small Parts Set X-12 PreciSensor Unit X-12 Alum Rear Cover X-12 12.0mm Sintered RotorX-12 13.0mm Sintered RotorX-12 Stock Spec Rotor 12.45mmWorks Team X-12 12.0mm RotorWorks Team X-12 12.5mm RotorWorks Team X-12 13.0mm RotorX-12 Stock Spec 1S LiPo RotorLRP Logo Sticker SheetBEC Stabilizing Capacitor SXX Low Profile Fan 30mm Motor Fan/Clamp, GunmetalRadical Cooling Set, Blue SXX Power Cap 3.7-4.8V SXX Power Cap 6.0-7.4V70mm High Flex Sensor Wire100mm High Flex Sensor Wire150mm High Flex Sensor Wire200mm High Flex Sensor Wire

:: Lubes & Adhesives / Decals / Misc.1105159615976588659166366727

716717381638203834

1111112

11112

FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape

Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo Sticker

28:: Tools111114501541154215431544154515461547154815511553155415611562156315641565156715891590159216551656165716581659166016611662166316641665166616671668166916701671167216731674

1719173737183719372039876429695674947709

111111111111111111111111111111111111111111

11

1212121111

12

FT Turnbuckle WrenchFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT 8-Piece 1/4” Hex Drive SetFT 1/4” Hex Drive Handle, without tipsFT 1/4” Hex Drive .050” TipFT 1/4” Hex Drive 1/16” TipFT 1/4” Hex Drive 5/64” - 2.0mm TipFT 1/4” Hex Drive 3/32” TipFT 1/4” Hex Drive 1.5mm TipFT 1/4” Hex Drive 2.5mm TipFT 1/4” Hex Drive 3/16” Nut Driver TipFT 1/4” Hex Drive 1/4” Nut Driver TipFT 1/4” Hex Drive 11/32” Nut Driver TipFT 1/4” Hex Drive 5.5mm Nut Driver TipFT 1/4” Hex Drive 7.0mm Nut Driver TipFT 1/4” Hex Drive 8.0mm Nut Driver TipFT 1/4” Hex Drive 5/64” - 2.0mm Ball End TipFT 1/4” Hex Drive 3/32” Ball End TipFT 1/4” Hex Drive Standard Screwdriver TipFT 1/4” Hex Drive Phillips Screwdriver TipFT 1/4” Hex Drive 2.5mm Ball End TipFT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, SetV2 Stamped Multi-tool4 Inch Nylon Wire Ties

:: 1/18 Kits and RTR’s

:: 1/12, 1/10 Kits and RTR’s

201032011020115201182012120130

204240207023702970307034703770467047704870497050705270927093802080229039904090419050906230101301089000490005900069000790010

111111

11111111111111111111111111111

RC18B2 - RC18T2 Team KitRC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 RTR Brushless (ready-to-run)RC18LM RTR (ready-to-run)

Nitro TC3 RTR Plus (ready-to-run)FT 12R5.2 KitRC10T4.1 FT KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RS RTR, Lucas Oil (ready-to-run)SC10 RS RTR, Monster Energy (ready-to-run)SC10 RS RTR, Pro Comp (ready-to-run)SC10 RS RTR, Rockstar/Makita (ready-to-run)SC10 RS RTR, Hart and Huntington (ready-to-run)Quaifier Series - Pro Lite 4x4 RTR (ready-to-run)GT2 RS Truck Nitro RTR (ready-to-run)SC10GT RTR (ready-to-run)FT RC10R5 KitFT RC10R5.1 KitRC10B4.1 RTR 2.4GHz Brushless (ready-to-run)FT RC10B4.1 Worlds KitFT RC10B4.2 KitSC10B RS RTR (ready-to-run)FT B44.2 4WD Buggy KitTC4 Club Racer 4WD Touring Car Race RollerFT TC6.1 WC 4WD Touring Car KitSC10 4x4 KitSC10 4x4 Lucas Oil RTR (ready-to-run)SC10 4x4 Pro Comp RTR (ready-to-run)SC10 4x4 Rockstar/Makita RTR (ready-to-run)SC10 4x4 FT Kit

:: 1/8 Kits and RTR’s205012050220503

20504

8090580906809078090880912

80933

80934

111

1

11111

1

1

MGT 4.60 SE RTR (ready-to-run)MGT 8.0 Nitro RTR (ready-to-run)Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8.2 Nitro Buggy FT KitRC8.2e Electric Buggy FT KitRC8.2e Electric Buggy RTR (ready-to-run)RC8T Championship EditionRC8T-RS “Race Spec” Nitro Truggy RTR (ready-to-run)SC8.2e Short Course Race Truck, Rockstar/Makita Electric RTR (ready-to-run)SC8.2e Short Course Race Truck, Slick Mist ElectricRTR (ready-to-run)

29

:: ApparelSP35**SP36**SP37**SP38SP39

SP66**SP67**SP68**SP69**

SP70**SP71**SP73**SP74**SP75**SP76**SP77**SP78**SP79**SP411SSP411LSP413SSP413LSP417SP418

SP420**SP421SSP421LSP422SSP422LSP423SSP423LSP424SSP424L

715110684

111111111

111111111111111

Pr.1111111111

Reedy 09’ White T-Shirt (L, XL, 2XL)Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL)Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)Reedy Trucker HatReedy PatchStencil Blue T-Shirt (S, M, L, XL, 2-6XL)AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)AE Stencil Blue T-Shirt (M, L, XL, 2XL)AE 26 Time World Championship T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Associated Windbreaker (S, M, L, XL, 3XL)Associated Winter Jacket (S, M, L, XL, 2XL)AE Long Sleeve T-Shirt (S, M, L, XL, 2XL)AE White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Blue T-Shirt (S, M, L, XL, 2-6XL)AE Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL) AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)AE Hat 11’ Flat Bill Black S/MAE Hat 11’ Flat Bill Black L/XL26 Time World Championship Hat S/M26 Time World Championship Hat L/XL1/10 FT Motor BagFactory Team 1/10 Car Carrier BagAE Pit Gloves (M, L, XL)AE 2012 Hat, Black, Flat Bill, S/MAE 2012 Hat, Black, Flat Bill, L/XLAE 2012 Hat, Black, Curved Bill, S/MAE 2012 Hat, Black, Curved Bill, L/XLAE 2012 Hat, White, Flat Bill, S/MAE 2012 Hat, White, Flat Bill, L/XLAE 2012 Hat, White, Curved Bill, S/MAE 2012 Hat, White, Curved Bill, L/XLReedy 2009 Track BannerTeam Associated Track Banner

** Use part number plus the desired size when ordering!

:: Contact Information

Associated Electrics, Inc.26021 Commercentre Drive

Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com

http://www.RC10.comhttp://twitter/Team Associated

http://bit.ly/AEonFacebook

call: (949) 544-7500fax: (949) 544-7501

Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!

www.TeamAssociated.com. - www.RC10.com

30:: Notes

Ride Height:

I O

A CB

Driver: Date: Track: Event:Conditions: Indoor Outdoor Temp. Rev.1Setup Sheet

:: For more setups, visit RC10.com and click on “Setup Sheets”

Front Suspension

Front Shocks

Electronics / Weight

DifferentialsDrivetrain

Front Tires

Race and Vehicle Comments

Other

Rear Tires

Track Info

Rear Suspension

Rear Shocks

Anti Roll Bar:

NoneBlack (soft)Silver (med)Gold (hard)

Rear Hub Carriers:0°0.5°1°1.5°

Spring: Piston:Shock Oil: Limiter:

Motor & Wind:Pinion: Spur Gear:Batteries:Battery Placement:Ballast Weight: Chassis Weight:

Slipper:2 Pads 3 Pads 4 PadsNotes:

Ball:Gear:Notes:

Tire:Compound:Insert: Wheel:

Qualify: Main: Finish: TQ:Comments:


Surface:DirtCarpetAstroMulti

Traction:LowMedHigh

Moisture:WetDampDry

Conditions:GroovedDustySmoothBumpyHard PackLoamy

Radio:Throttle / Brake e.p.a:Throttle / Brake expo:Servo: Steering Expo:ESC: ESC Settings:

Body Type:Wing Type: Wing Angle:


Washers:

Washers:

Washers:

Ride Height:

Aluminum Hub Tower:ABC

Caster Block Spacing:ForwardBack

Caster:

20°25°30°

1 2 3

1

1

2

2

I O

A CB D

Camber:

Inner Toe:

Anti-Squat:

Camber:

Toe:12 3 -1 -1

0 3°

2°

2mm1mm

2mm

Black

30wt

Thin pad back, thick pad front

Proline VortexVortex

30wt3

VTS

Stock Stock

2

White1.6 1.6

24mm

24mm

Wheelbase:LongMediumShort

Chassis BraceGround Flat:

Steering Rack:

FrontBack

32:: Hardware - 1:1 Scale View

Notes:

E-clip 1/8 (6299)

Clips

2-56x1/8 (9645)

2-56x5/16 (4334)

4-40x5/16 (6919)

4-40x3/8 (6917)

4-40x7/16 (2221)

4-40x3/4 (7413)

4-40x7/8 (91311)

3x8mm (31532)

Button Head (bhcs)

4-40 Aluminum Locknut (4449)

4-40 Plastic Nut (6472)

5-40 Diff Locknut (6629)

8-32 LP Steel Locknut (6953)

8-32 Steel Locknut (6952)

Nuts (lock/plain)

5/64 Diff Thrust Balls (6574)

3/32 Carbide Diff Balls (6581)

Diff Balls

Ballstuds

Black .20 Short (3981)

Black .30 Short (3983)

Silver .20 Short (6276)

Silver .30 Long (6277)

Silver .40 (6278)

.030 Ballstud Washer (9630)

.030 Nylon Spacer (4187)

Servo Mount Washer (7337)

#4 Washer (6936)

3/16 Axle Shim - Silver (7368)

FT Ballstud Washer, Aluminum(1mm and 2mm, 4 each) (31286)

Shims and Washers

4-40x3/8 (6292)

4-40x1/2 (6922)

4-40x5/8 (6915)

5-40x1/2 (9269)

Flat Head (fhcs)

Ball Bearings

Steering Rack Bearing (3971)

3/16x3/8 (3977)

3/16x1/2 RS (7935)

10 x 16mm (9832)

Cap Head (shcs)

2-56x 3/16 (9898)

4-40x1/4 (6285)

4-40x5/16” (6932)(4145, aluminum)

4-40x3/8 (6924)w/hole (6929)

4-40x1/2 (6925)

4-40x5/8 (6926)

4-40x3/4 (6927)

4-40x7/8 (7738)

4-40x1 (6928)

4-40x1 1/4 (6913)

4-40x1 3/4 (9833)

5-40x7/16 (9643)

5-40x9/16 (9644)

5-40x7/3/4 (9835)

Ride Height:

I O

A CB

Driver: Date: Track: Event:Conditions: Indoor Outdoor Temp. Rev.1Setup Sheet

:: For more setups, visit RC10.com and click on “Setup Sheets”

Front Suspension

Front Shocks

Electronics / Weight

DifferentialsDrivetrain

Front Tires

Race and Vehicle Comments

Other

Rear Tires

Track Info

Rear Suspension

Rear Shocks

Anti Roll Bar:

NoneBlack (soft)Silver (med)Gold (hard)

Rear Hub Carriers:0°0.5°1°1.5°


Motor & Wind:Pinion: Spur Gear:Batteries:Battery Placement:Ballast Weight: Chassis Weight:

Slipper:2 Pads 3 Pads 4 PadsNotes:

Ball:Gear:Notes:


Qualify: Main: Finish: TQ:Comments:


Surface:DirtCarpetAstroMulti

Traction:LowMedHigh

Moisture:WetDampDry

Conditions:GroovedDustySmoothBumpyHard PackLoamy

Radio:Throttle / Brake e.p.a:Throttle / Brake expo:Servo: Steering Expo:ESC: ESC Settings:

Body Type:Wing Type: Wing Angle:


Washers:

Washers:

Washers:

Ride Height:

Aluminum Hub Tower:ABC

Caster Block Spacing:ForwardBack

Caster:

20°25°30°

1 2 3

1

1

2

2

I O

A CB D

Camber:

Inner Toe:

Anti-Squat:

Camber:

Toe:12 3

Wheelbase:LongMediumShort

Chassis BraceGround Flat:

Steering Rack:

FrontBack

Associated Electrics, Inc.26021 Com

mercentre Dr.

Lake Forest, CA 92630 USAhttp://w

ww

.TeamAssociated.com

http://ww

w.RC10.com

http://twitter/Team

_Associatedhttp://bit.ly/AEonFacebook

call: (949) 544-7500 - fax: (949) 544-7501Check out the follow

ing web sites for all of our kits,

current products, new releases, setup help, tips, and racing info!

ww

w.Team

Associated.com. - w

ww

.RC10.com

Documents

Associated Electrics, Inc. Customer Service 26021 ...petitrc.com/setup/associated/setupb4/B4.2_Manual.pdf · maintaining your new RC10 B4.2. Please take a moment to read through this