Upload
jocastillo
View
231
Download
0
Embed Size (px)
Citation preview
8/10/2019 Assemble 1683
1/32
CR600/CR500 (MS-1683) Assembly Guide
1LCD MODULE ASSY
2UPPER CASE ASSY
3LOWER CASE ASSY
4ASSEMBLE UPPER CASE AND LOWER CASE
5KEYBOARD
6THERMAL-KITCPUDRAM AND WLAN MODULE
7ODD MODULE
8HDD MODULE
9BOTTOM DOOR ASSY
10BATTERY PACK
8/10/2019 Assemble 1683
2/32
CR600/CR500
MS-1683AssemblyGuide
1 LCD MODULE ASSY
1.1Assemble the MIC Module as left picture show
Component P/N Qty
MIC Module S34-2100910-K03 1
1.2Assemble the WIRELESS L-Antenna board to
the LCD cover fixed position as left picture shows.
Component P/N QtyL-Antenna S79-1800K80-J51 1
1.3Assemble the WIRELESS R-Antenna board to
the LCD cover fixed position as left picture shows.
Component P/N Qty
R-Antenna S79-1800K70-J51 1
LCD Cover 307-682A211-Y31 1
8/10/2019 Assemble 1683
3/32
CR600/CR500
MS-1683AssemblyGuide
1 LCD MODULE ASSY
1.4Assemble the 8 screws (M2*3mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Display Module S1J-A42G002-S02 1
LCD BRACKET-L E2M-6810211-A89 1
LCD BRACKET-R E2M-6810111-A89 1
Screw E43-1203003-H29 8
1.5 Connect the Coaxial CableCamera Cable
in the direction of the arrow in the picture;
1.6Assemble CMOS Camera Module follow the
instruction as left picture shows.
AttentionDont assemble the CMOS Camera
Module with too strong force avoid damage the
module.
8/10/2019 Assemble 1683
4/32
CR600/CR500
MS-1683AssemblyGuide
1 LCD MODULE ASSY
1.7Connect LVDS Cable to Display Module and
fix the cable with black tape;
Component P/N Qty
LVDS Cable K19-3028001-H39 1
1.8Assemble the display module to LCD cover;
1.9Assemble the 2 screws (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
;
Component P/N Qty
Screw E43-1255007-H29 2
8/10/2019 Assemble 1683
5/32
8/10/2019 Assemble 1683
6/32
CR600/CR500
MS-1683AssemblyGuide
1 LCD MODULE ASSY
1.13When assemble the LCD bezel, should begin
from the two sides, then the upside to downside
assemble the 4screws (M2.5*5mm).;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
LCD Bezel 307-681B211-Y31 1
1.14Assemble the 8 cover rubber
Component P/N Qty
UP Rubber E2Y-6810111-Y40 4
DOWN Rubber E2Y-6740611-Y40 4
8/10/2019 Assemble 1683
7/32
CR600/CR500
MS-1683AssemblyGuide
2UPPER CASE ASSY
2.1Insert the T/P module FFC according to
direction of left pic shows; then close the
connector that stabilize the T/P cable,;
Component P/N Qty
FFC Cable(To MB) K1C-1012040-J36 1
2.2Assemble the Touchpad Module to Upper
Case fixed position,
Component P/N Qty
Touchpad Module S78-3700360-SD2 1
Upper Case 307-682C111-TC7 1
8/10/2019 Assemble 1683
8/32
CR600/CR500
MS-1683AssemblyGuide
3LOWER CASE ASSY
3.1Assemble the RJ11 to Lower case;
Component P/N Qty
RJ11 CABLE K10-3002131-V03 1
3.2Assemble the Speaker module to lower case
then lock the 4 screws (M2*3mm),;
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 4
Speaker Module S33-A020310-F33 1
Lower Case 307-681D221-Y31 1
8/10/2019 Assemble 1683
9/32
CR600/CR500
MS-1683AssemblyGuide
3LOWER CASE ASSY
3.3Assemble the B/T module;
Component P/N Qty
Bluetooth Module 605-6837D-160 1
Main Board 607-16821-01S 1
3.4Assemble the main board to Lower case; then
Lock the 1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
8/10/2019 Assemble 1683
10/32
CR600/CR500
MS-1683AssemblyGuide
3LOWER CASE ASSY
3.5Assemble the USB board, then lock the
1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
USB board 607-1682A-01S 1
Screw E43-1255007-H29 1
3.6Assemble the USB board cable as left pic
shows:
Component P/N Qty
USB board FPC K1C-1012039-J36 1
8/10/2019 Assemble 1683
11/32
CR600/CR500
MS-1683AssemblyGuide
4ASSEMBLE UPPER CASE AND LOWER CASE
4.1Assemble the 4 screws (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
4.2Assemble 8 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 8
4.3Assemble 5 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 5
8/10/2019 Assemble 1683
12/32
CR600/CR500
MS-1683AssemblyGuide
4ASSEMBLE UPPER CASE AND LOWER CASE
4.4Connect the LVDS cable as pic shows:
4.5Connect the Touchpad cable.
4.6Assemble the modem, then lock the 2
screws(M2*3mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
MODEM S52-2801180-C59 1
Screw E43-1203003-H29 2
8/10/2019 Assemble 1683
13/32
CR600/CR500
MS-1683AssemblyGuide
4ASSEMBLE UPPER CASE AND LOWER CASE
4.7Assemble the 4 screws(M2.5*5mm) that
stabilize the LCD hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
4.8 Assemble the 2 screws(M2*3mm) that
stabilize the hinge Cap
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 2
8/10/2019 Assemble 1683
14/32
CR600/CR500
MS-1683AssemblyGuide
4ASSEMBLE UPPER CASE AND LOWER CASE
4.9Assemble Launch board according to the
direction that pic shows;
4.10Assemble the 2 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Launch board 607-1682B-01S 1
Screw E43-1203003-H29 2
8/10/2019 Assemble 1683
15/32
CR600/CR500
MS-1683AssemblyGuide
5KEYBOARD
5.1Insert the cable; close connector according to
the direction as pic shows;
Component P/N Qty
Keyboard S1N-3UUS1B1-C54 1
5.2Assemble the 5 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 5
5.3Assemble the Hinge Cover;
Component P/N Qty
Hinge Cover 307-682E221-Y31 1
8/10/2019 Assemble 1683
16/32
8/10/2019 Assemble 1683
17/32
CR600/CR500
MS-1683AssemblyGuide
6THERMAL-KITCPUDRAM AND WLAN MODULE
6.4Assemble CPU Moduleas below, Close the CPU
Slot with Screw Driver.
.
Component P/N Qty
CPU A09-21201G6-I06 1
6.5: Assemble the Fansink and FAN cable, after
that lock the 5 screws (M2.5*5mm).
Attentionthe screw driver torque is 2.0-2.2Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 5
Fansink E32-0800220-F05 1
2
5
1
4
3
8/10/2019 Assemble 1683
18/32
CR600/CR500
MS-1683AssemblyGuide
7ODD MODULE
7.1Assemble ODD Bezel as below.
Component P/N Qty
ODD Bezel E2P-681F211-Y31 1
7.2Assemble ODD Bracket as below, then lock 2pcs
M2*3mm Screws
Component P/N Qty
Screw E43-1203003-H29 2
ODD Bracket E2M-6510211-Y28 1
ODD Module S7D-2270015-H44 1
8/10/2019 Assemble 1683
19/32
CR600/CR500
MS-1683AssemblyGuide
7ODD MODULE
7.3Assemble the ODD Module according to the
direction as pic shows;
7.4Assemble the 1 screw(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 1
8/10/2019 Assemble 1683
20/32
CR600/CR500
MS-1683AssemblyGuide
8HDD MODULE
8.1Assemble the HDD bracket;
Component P/N Qty
HDD Bracket 307-6810111-A89 1
HDD Module S71-2425521-W36 1
8.2Assemble the 2 screws(M3*3.5mm) that
stabilize the bracket;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1303501-H29 2
8/10/2019 Assemble 1683
21/32
CR600/CR500
MS-1683AssemblyGuide
8HDD MODULE
8.3Assemble the HDD Module according to the
direction as pic shows;
8.4Assemble the 2 screws(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 2
8/10/2019 Assemble 1683
22/32
CR600/CR500
MS-1683AssemblyGuide
9BOTTOM DOOR ASSY
9.1Assemble the Bottom door, then lock the 4
screws (M2.5*5mm).
.
Attention: the screw driver touque is: 2.0-2.5Kgf-cm
Component P/N Qty
Bottom door 307-681J211-Y31 1
Screw E43-1255007-H29 4
8/10/2019 Assemble 1683
23/32
CR600/CR500
MS-1683AssemblyGuide
10BATTERY PACK
10.1Release the Release button and assemble
Battery Pack in the direction of arrow in the left
picture.
Component P/N Qty
Battery Pack S9N-2062200-CE1 1
10.2Shift Unlock button to lock Battery Pack.
8/10/2019 Assemble 1683
24/32
CR600/CR500MS-1683screws specification
Photo Screw specification Label
(M2.5*L5MM)black
(M2*L3MM)white
(M3*L3.5MM) white
8/10/2019 Assemble 1683
25/32
CR600/CR500MS-1683screws specification
BOTTOM DOOR ASSY total 19pcs screws,
specification
Photo Screw specification label
(M2.5*L5MM) black
8/10/2019 Assemble 1683
26/32
CR600/CR500MS-1683screws specification
2THERMAL-KIT 5pcs screws
specification
Photo Screw specification label
(M2.5*L5MM) black
4
5
3
8/10/2019 Assemble 1683
27/32
CR600/CR500MS-1683screws specification
3WIRELESS CARD and HDD ASSY total 5pcs screws,
specification
Photo Screw specification label
(M3*L3.5MM) white
(M2*L3MM)white
8/10/2019 Assemble 1683
28/32
CR600/CR500MS-1683screws specification
4UPCASE ASSY total 4pcs screws ,
specification
Photo Screw specification Label
(M2.5*L5MM) black
8/10/2019 Assemble 1683
29/32
CR600/CR500MS-1683screws specification
5LCD BEZEL total 4pcs screws,
specification
Photo Screw specification label
(M2.5*L5MM) black
8/10/2019 Assemble 1683
30/32
CR600/CR500MS-1683screws specification
6LCD MODULE ASSY total 16pcs screws ,
specification
Photo Screw specification label
(M2.5*L5MM) black
(M2*L3MM)white
8/10/2019 Assemble 1683
31/32
CR600/CR500MS-1683screws specification
8NB total 1pcs screw
specification
Photo Screw specification label
(M2.5*L5MM) black
8/10/2019 Assemble 1683
32/32
CR600/CR500MS-1683screws specification
9LOWER CASE total 4pcs screws
specification
Photo Screw specification label
(M2*L3MM)white