ASO EENT SHED MODEL: 30372…Absco Industries Assembly Instruction Manual ASO EENT SHED MODEL: 30372 3.00mW x 3.66mD x 2.10mH Model: 30372RK 19/09/18 1.4 1 Download the Absco Sheds

Absco Industries Assembly Instruction Manual

ABSCO REGENT SHEDMODEL: 30372RK3.00mW x 3.66mD x 2.10mH

Model: 30372RK 19/09/18 1.4 1

Download the Absco Sheds Assembly App for instructional videos

MANU FA CT UREDIN A US TR ALIA

SNAPTiTEAssemb ly

AU: 1800 029 701N Z: 0800 466 444

[email protected]

When laying concrete slab, ensure there is a rebated edge 25mm deep around the perimeter. This will help water egress from the base of the shed.

For construction in non-cyclonic areasWind rating: N2 as per AS4055-2012

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017

CONCRETE SLAB

2360mm1620mm

FRONT: 2.26mSIDE: 1.52mHEIGHT: 1.95m

We thank you for choosing an Australian madeshed. For further assistance please visit our detailed

instructional video library atHttp://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to benumber ONE, so please let us know what you think

of our instructions. Feedback makes us [email protected]

CONCRETE

REBATED EDGEBOTTOM CHANNEL

CONCRETE SLAB

75mm WIDE REBATE

100mm

WHEN LAYING YOUR CONCRETESLAB, ENSURE THERE IS A

REBATED EDGE 25mm DEEPAROUND THE PERIMETER

THIS WILL HELP WATER EGRESSFROM THE BASE OF THE SHED

Absco IndustriesPremier Shed Model: 23151GK

PAGE 01

CONCRETE SLAB

3100mm

3760mm



Model: 30372RK 19/09/18 1.4 2

GENERAL INSTRUCTIONS

• Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details.

• Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages.

SITE PREPARATION

• The site for the shed must be level. An uneven surface may result in misalignment of parts.

• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately illustrated on “FINAL CONSTRUCTION” page.

TOOLS REQUIRED

SAFETY NOTES

• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.

• Do not erect your shed in windy conditions.

• Ensure that the shed is securely anchored to a solid foundation immediately after construction is completed.

• It is highly recommended to erect the shed with two or more people.

RECOMMENDED

3mm

dril

l bit

10m

m d

rill b

itm

etal

/mas

onr

y



Model: 30372RK 19/09/18 1.4 3

COMPONENT PACKING LIST

Check off all components.

COMPONENTDESCRIPTION

PARTNo. CHECK COMPONENT

DESCRIPTIONPART

No. CHECKQTY QTY

2

8

2

2

6

2

4

1

1

2

STEEL SHEET1785mm X 711mm 34A


STEEL SHEET1725mm X 773mm A

STEEL SHEET1725mm X 773mm B

GABLE L/HL=1475mm 16L

GABLE R/HL=1475mm 16R

13ABRACEL: 393mm

97DL1 RIDGEBEAM

1

L = 1866.5mm

97DRRIDGEBEAM

ZARSP1 RIDGE BEAM JOINERL: 450mm

L = 1866.5mm

1785mm X 773mm 30ASTEEL SHEET


STEEL SHEET1546mm X 773mm 44L

STEEL SHEET1546mm X 773mm 44R


2 2



Model: 30372RK 19/09/18 1.4 4


1 479ACHANNELL = 1568mm

58ACHANNEL WITH HINGESL = 1725mm

58BCHANNELL = 1725mm

58CCHANNELL = 773mm

77AL

55CL

77BL

81BL

81LL

62BL

55CR

1

1

1

1

2

2

1

1

1

1

2

2

CHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1866.5mm

CHANNELL = 1866.5mm

77BR

81BR

81LR

62BR

77ARCHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1496.5mm

CHANNELL = 1866.5mm

CHANNELL = 1866.5mm



DESCRIPTIONPART

No. CHECKQTY QTY

81KL2 2CHANNELL = 1829.5mm

81KRCHANNELL = 1829.5mm

62AL2 2CHANNELL = 1829.5mm

62ARCHANNELL = 1829.5mm

58C

58B58A

79A

77AL

JOIN>>

55CLJOIN>>

77BL

JOIN>>

81BLJOIN>>

81LL

JOIN>>

62BLJOIN>>

81KLJOIN>>

62ALJOIN>>

62AR

JOIN>>

81KR

JOIN>>

62BR

JOIN>>

81LR

JOIN>>

81BR

JOIN>>

77BR

JOIN>>

55CR

JOIN>>

77AR

JOIN>>

12



Model: 30372RK 19/09/18 1.4 5


1

12A2DOORSTRAPL: 6.5"

14A2 CAP GABLEL: 170mm 1 ASSEMBLY

INSTRUCTIONS



DESCRIPTIONPART

No. CHECKQTY QTY

INSTRUCTIONS & FITTINGS PACKET

4

4

1

2 89AJAMB L= 1785mm

90AJAMB L= 1568mm

91AJAMB L= 1120mm

89CJAMB L= 1725mm

87BLIP TRIM L= 1546mm

CSJ12 CHANNEL JOINERL= 200mm

Part No. Here

Part No. Here

Part No. Here

Part No. Here

87B

CSJ

DOORPADBOLT

HASP23

SELF TAPPING SCREWSPACKET CONTAINING 2201

DOORPADBOLT

3/16 COUNTERSUNKSCREWS & NUTS12

3/16 ROUND HEADBOLTS & NYLOCK NUTS8 3.2 x 8mm

BLIND POP RIVETS12

PSTKDBL - DOUBLE DOOR FITTINGS PACK

PACK12P - SCREW PACK 12

PACK12PSCREW PACK 121

PHILLIPS DRIVER BIT3mm DRILL BIT DRILL FAST038

FAST007FAST006

10 16mm TEKSCREWS FAST014

11

11

SELF TAPPING SCREWSPACKET CONTAINING 100

PSTKDBLDBL DOOR FITTINGS PACK



Model: 30372RK 19/09/18 1.4 7

SNAPTiTE ASSEMBLY GUIDE

The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners.

To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.

Each perimeter channel must fi nish fl ush with the edges of the sheets. Simply tap the channel along the sheets until each end is neatly fl ush. If you need to remove channels from the panels, slide it off from the side.

Channel locks the shed panel into position without the need for screws!

FASTENING SYMBOLS

Secure channel to sheeting by SNAPTiTE fastening method.

Join components together with one screw at this location only, as some channels have extra holes that are not required for this model of shed.

Do not join components together at this location yet, as the screws may obstruct further assembly of the other components.

Join components together by pre-drill-ing the holes fi rst. Use one component as template to mark where the holes are and drill with a 3mm drill bit.

3mm pop rivet

4mm nut and bolt set.

DSNAPT TEi



Model: 30372RK 19/09/18 1.4 8

Guide on Joining Spliced ChannelsThe text marked on all parts must be shown on the same side as each other

Step 1.Position the channels and the CSJ joiner so the centre of the CSJ is in line with the end of each channel to be joiner together.

Step 2.Join the fi rst channel to the CSJ by inserting the centre of the CSJ, on an angle, to the end of the channel where the JOIN>> text is marked.

Push down one side of the CSJ until you hear a ‘click’.

Step 3.Join the second channel to the CSJ by positioning the <<JOIN of the channel at the centre of the CSJ, on an angle. Push the CSJ into the channel until you hear a ‘click’.

Finished Channel.The joined channels should now look like the picture with the CSJ positioned equally inside of the joined channels.

Drill out holes with 3mm drill bit in CSJ to match the holes in channel and secure with the screws supplied.These may have to be temporarily removed during assembly.

= =

JOIN>> <<JOIN

CSJ

=

=

JOIN>> J

==

JOIN>> SJ

= =

JOIN>><<JOIN

= =

JOIN>> <<JOIN

Finished Spliced Channel

Channel

Push

20mm 15mm

CSJ.

...



Model: 30372RK 19/09/18 1.4 9

PRE-ASSEMBLY OF SPLICED CHANNELS

NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them.

Join together 24 x channel sections using 12 x channel joiners (Part CSJ)

=

=

=

=

=

1 X 77BR

2993mm

1 x 77A

1 x 77B

1 x 55C

2 x 62B

1 x 81B

81BR

81BL

62BL

62BR

55CR

55CL

77AR

1 X 77AR1 X 77AL

1 X 77BL

1 X 55CR1 X 55CL

2 X 62BR2 X 62BL

1 X 81BR1 X 81BL

=

2 X 81LR

2 x 81L

81LR

81LL

2 X 81LL

3733mm

77BL

77BR

77AL

= 2 x 62A

62AL

62AR

2 X 62AR2 X 62AL

=

2 X 81KR

2 x 81K

81KR

81KL

2 X 81KL

3659mm



Model: 30372RK 19/09/18 1.4 10

Tek screw driver bit

Push

Guide on Joining a Spliced Ridge BeamFollow these three steps to assemble a ridge beam.

Step 1.Place two ridge beams as shown and push them together. Slide the cap of one under the other.

NOTE.There is a 50mm overlap of the ridge caps when the beams are in position.

Step 2.Use the ZARSP to connect at the centre of the two ridge beams. Be sure it is pushed in fully.

Step 3.Turn over the ridge beam. Measure 250mm from the middle along the centre of one ridge beam, mark spacings of 50mm. Fasten with a Tek screw at each marking.

Repeat to the other side of the ridge beam assembly.

TIP: Predrilling each hole with the 3mm drill bit makes it easier to fasten.

50mm225mm

ZARSP

Finished Spliced Ridge Beam

FinishedSpliced Ridge Beam

ZARSP

Ridge Beam

Self drilling Tek screw



Model: 30372RK 19/09/18 1.4 11

PRE-ASSEMBLY OF SPLICED RIDGE BEAM

.

.

1x 97DL 1x 97DR

= 1x 97D

3733mm Overall length

ZARSP

225mm

97DL

97DR

16mm

16mm



Model: 30372RK 19/09/18 1.4 12

OVERVIEW OF ROOF COMPONENTS

OV

ER

VIE

W O

F R

OO

F C

OM

PO

NE

NTS

44R

45A

45A

45A

44L

44R

45A

45A

45A

44L

81L

87B

14A

87B

97D

81L

62B

87B

87B



Model: 30372RK 19/09/18 1.4 13

OVERVIEW OF WALL COMPONENTS

OV

ER

VIE

W O

F W

ALL

CO

MP

ON

EN

TS

32A

31A

31A

31A

32A

81K

91A 91

A

89A

90A

34A

A

B

34A

55C

79A

89A

22A

62A

77B

16R

81B

30A

13A

31A

31A

30A

32A

31A

31A

31A

32A

62A

16R

77A

13A

16L

81K

16L



Model: 30372RK 19/09/18 1.4 14

REAR PANEL ASSEMBLY

1x required.

30A

31A

31A

30A

81B

SNAPT

TEi

SNAPT TEi

77B



Model: 30372RK 19/09/18 1.4 15

ROOF PANEL ASSEMBLY

2x required.

Fit 81L to edge of sheet with pre-punched holes.

44L

45A

45A

45A

44R

87B

81L

62B

SNAPT TEi

SNAPT TEi

87B



Model: 30372RK 19/09/18 1.4 16

SIDE PANEL ASSEMBLY

2x required.

62A

81K

SNAPT TEi

SNAPT TEi

SMALL PAN

SMALL PAN

32A

31A

31A

31A 32A



Model: 30372RK 19/09/18 1.4 17

FRONT PANEL ASSEMBLY

89A

89A

34A1x required.

34A

77A

90A

79A

55C

SNAPT TEi

SNAPT TE

i

SNAPT TEi

SNAPT TEi



Model: 30372RK 19/09/18 1.4 18

DOOR PANEL ASSEMBLY

58C

58C

58C

12A

58C

58A

58A

A

B

89C

58B

A

B

SNAPT TEi

SNAPT TEi

SNAPT TEi

SNAPT TEi

Vertical door channels are installed in the opposite orientation compared to the horizontal door channels.

Four hole set for padbolt connection.

Short fl ange of channel

Long fl ange of channel

D

D

D

D

D

D

D

D

1x required.



Model: 30372RK 19/09/18 1.4 19

DOOR PANEL ASSEMBLY

Nuts and bolts may be used instead of pop rivets by drilling out hinge holes using a 4mm drill bit. Both are supplied.

The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and secure with screws.

91A

91A

A

B



Model: 30372RK 19/09/18 1.4 21

PANEL CONSTRUCTION

NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. The base channels are not pre-punched.

Pre-punched channel to match ridge beam holes

Side wall channels fit into the notched rear wall channels.

Pre-punched holes in roof panel to

this side

for connection to fro

nt and rear walls.

Orient panel so channel (62B) goes into ridge beam

Channel (81L) this end

97D

D

D

D

D

D

D

D

D

D

D

D

D

D

DD

DDD

D

D

DD

D

DDD

D



Model: 30372RK 19/09/18 1.4 22

INSIDE VIEW OF FIXING

INSIDE VIEW OF FRONT WALL

OUTSIDE VIEW

37mm

ROOR OVERHANGSALL WALL PANELSBY 37mm

13A

Secure ridge beam to gable sections with two screws at each end. Secure each roof panel with one screw in each corner only at this stage

After attaching both roof panels to walls as shown above, fit one regent brace to the ridge beam and front wall as shown. You will have to remove and replace existing screws at fixing locations. Repeat this procedure for the rear wall regent brace



Model: 30372RK 19/09/18 1.4 23

FINAL CONSTRUCTION

Each anchor consists of one nut, bolt, M10 dynabolt and steel angle.Drill a 10mm hole into the wall sheet.Drill a 10mm hole into the concrete.

Bolt and Nut*M10 4.6/S

Steel Angle*35 x 35 x 3

M10 Dynabolt*

* Denotes hot dip galvanised fi nish

Wall Sheet

Slab

14A

Bend the top and bottom flanges as shown, then hook the bottom flanges under the top channel and screw top to the ridge beam with two screws.

ANCHORING OF SHED

Location of 16concrete anchors

250

250

250

250

1000

1000

700

700

640

640

640

640

640

640

640

640

640

640

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

DD

D

D

DD

D



Model: 30372RK 19/09/18 1.4 24

Absco Gable Roof Shed Notes

• 1.G This instruction manual shall be read in conjunction with other consultants drawings, specifi cations and written instructions provided by Absco and/or their representatives.

• 2.G The drawings provided herein are for installation and structural engineering purposes only.

• If discrepancies are discovered within the documentation provided, these shall be brought to the attention of Absco and written approvals obtained prior to commencing the affected section of work.

• 3.G If in doubt ask.

• 4.G Until approvals from the local authorities are obtained, commencement of construction from these drawings shall not commence.

• 5.G Unless varied by the project specifi cation, all materials and workmanship shall be undertaken in accordance with the relevant Australian standards and the by-laws and ordinances of the relevant building authorities.

• 6.G All dimensions indicated in these drawings shall be verifi ed on site by the installation contractor. Scaling of drawings shall not be undertaken.

• 7.G Prior to commencing works on site, the contractor shall verify the position of all services in the area to ensure that the construction does not interfere with any of those services.

• 8.G During installation on site the shed structures shall be maintained in a stable condition with no part becoming overstressed or permanently deformed.

• 9.G In circumstances where the shed has been installed in a manner which is inconsistent with the installation manual, structural certifi cation shall be void.

• 10.G The structural components detailed within this installation manual have been designed for the following loads in accordance with AS/NZS1170 based on a Class 10a, Type 2 structure:

• Roof Live Load: 0.25 kPa uniformly distributed or 1.1 kN concentrated as per AS/NZS1170.1

• Wind Load: Classifi cation N2, Non-Cyclonic to AS4055 where Vu = 40 m/s, Vs = 26 m/s

Windward wall Cpe = 0.7

Leeward Wall Cp,e = -0.3 to -0.5 as applicable based on shed geometry

Side Wall Cp,e = -0.5 to -0.65 as applicable based on shed geometry

Roof Cp,e = -0.5 to -1.3 depending on wind direction

6-12 Activity St, Acacia Ridge QLD 4110PO Box 119, Acacia Ridge QLD 4110

AU: 1800 029 701N Z: 0800 466 444

[email protected]

General



Model: 30372RK 19/09/18 1.4 25

Absco Gable Roof Shed Notes

• 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 2312-2002.

• 2.S All structural steelwork detailed within this installation manual shall be minimum Grade

• 550 for roll formed sections (including roof and wall sheeting) and Grade 250 for angle sections.

• 3.S All roof, and wall sheeting shall be minimum base metal thickness of 0.3mm

• 4.S All snaptite channels and jambs shall be minimum base metal thickness of 0.42mm

• 5.S All top hats shall be minimum base metal thickness of 1.0mm

• 6.S All screw fasteners shall be Phil Pan Head Zinc Plated #8 x 3/4” (STP0820)

• 7.S All bolt fasteners for anchoring shall be M10 minimum grade 4.6/S

• 8.S Installation of screw fasteners shall generally be undertaken in accordance with the relevant provisions of AS1562.

Steelwork

• 1.F The supporting slab foundation for the garden shed shall be of a minimum size indicated on the installation manual. The top surface of the formed slab shall be level and free of any irregularities which would inhibit the installation of the shed.

• 2.F The structural engineering design for the supporting slab foundation shall be undertaken by a suitably qualifi ed structural engineer. The design shall consider all relevent provision of AS3600 and AS2870.

• 3.F Between adjacent footings or excavations, the contractor installing the slab foundation shall not exceed a rise of 1 in a run of 2 in line of slope.

• 4.F Unless approved in writing by the slab foundation engineer, the limits of excavations near existing footings shall be in accordance with that indicated below.

Supporting Slab and Foundations

The contactor shall undertake investigatory localised excavations near existing footings to ascertain their depth prior to excavating adjacent to them. It is noted that excavating to a depth below that indicated above shall not be undertaken without the written approval from the engineer.



Model: 30372RK 19/09/18 1.4 26

Australia Product Warranty Against Defects

• Absco Sheds, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel.

• We are pleased to advise we warrant that the steel coating will not rust, crack, fl ake peel or blister for 30 years from date of purchase, when installed within Australia.

• This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of steel debris left from cutting, grinding or drilling operations) that has not been removed after building construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.

• This warranty covers any Absco product used for normal domestic use and installed in accordance with the installation instructions.

• The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.

• This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding padbolts).

• The warranty is limited to replacement and delivery of components and does not include any labour or installation costs. The benefi ts given by the warranty are in addition to your other rights and remedies under a law in relation to the goods or services to which the warranty relates.

• The warranty applies to the exclusion of all other representations, guarantees or warranties express or implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and is not transferable. You are entitled to a replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further information go to http://www.consumerlaw.gov.au

• Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of purchase here: www.absco.com.au/register_warranty.php

• In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details of the defect, including component part numbers, together with proof of purchase documentation (or on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim, the Customer Service Manager will contact you within three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making the claim.

THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110

PHONE: 1800 029 701 FAX: 07 3344 1191 EMAIL: [email protected]

Issued 01 January 2018



Model: 30372RK 19/09/18 1.4 27

Absco Sheds Storage Guidelines

• Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.

• Other weather conditions such as extreme heat and extreme cold, moist or dry air can infl uence the effects of concrete fl oor moisture and/or condensation on the underside of the roof sheets.

• Absco Sheds and storage units are primarily used for storage of garden equipment such as lawnmowers, wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the concrete fl oor on timber slats.

• Waterproof sealants may be used to offer further protection where required around joins and screw fi xings, as can rubber door seals and other products which are available from most hardware outlets.

• Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with water accumulating and being trapped inside the shed.

• Absco accepts no responsibility for water entry, fl oor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.

6-12 Activity St, Acacia Ridge QLD 4110PO Box 119, Acacia Ridge QLD 4110

AU: 1800 029 701N Z: 0800 466 444

[email protected]

Documents

ASO EENT SHED MODEL: 30372…Absco Industries Assembly Instruction Manual ASO EENT SHED MODEL: 30372 3.00mW x 3.66mD x 2.10mH Model: 30372RK 19/09/18 1.4 1 Download the Absco Sheds