Aruba ACMP 6.3 Aruba Certified Mobility Professional 6.3 ... · It guided me step by step through the course. After studying for a month using it I achieved the highest in the whole

Testkings.ACMP_6.3.165 questions

Number: ACMP_6.3Passing Score: 800Time Limit: 120 minFile Version: 4.6

http://www.gratisexam.com/

Aruba ACMP_6.3

Aruba Certified Mobility Professional 6.3

My problem had solved because the products of it was very reliable

This dumps is valid and awesome, I passed by just 2 days practice.

A questions are all in the dump file and there is the additional question

It was one and only which took me towards the biggest success without finding too much issues or worries in any way.

It guided me step by step through the course. After studying for a month using it I achieved the highest in the whole city

Exam A

QUESTION 1Which of the following Aruba controllers is able to provide IEEE 802.3af? (Choose two)

A. 3200B. 620C. 650D. 6000 with M3E. 7000

Correct Answer: BCSection: (none)Explanation

Explanation/Reference:Explanation:

QUESTION 2What is the maximum number of remote APs supported by a 3600 controller?

A. 512B. 1024C. 128D. 256E. 2048

Correct Answer: ASection: (none)Explanation

Explanation/Reference:correct answer.

QUESTION 3What is the first role a user is given when a user associates to an open WLAN?


A. The guest post authentication roleB. The initial role in the captive portal profileC. The role in the server group profileD. The initial role in the AAA profileE. The initial role in the 802.1x profile

Correct Answer: DSection: (none)Explanation


QUESTION 4Which of the following could be used to set a user's post-authentication role or VLAN association? (Choose two)

A. AAA default role for authentication methodB. Server Derivation RuleC. Vendor Specific AttributesD. AP Derivation RuleE. The Global AAA profile



QUESTION 5

Which describe "roles" as used on Aruba Mobility Controllers? (Choose two)

A. Roles are assigned to users.B. Roles are applied to interfaces.C. Policies are built from roles.D. A user can belong to only one role at a time.E. Roles are a set of authentication rules

Correct Answer: ADSection: (none)Explanation


Real 8Aruba ACMP_6.3 Exam

QUESTION 6Which netdestination aliases are built into the controller? (Choose three)

A. logonB. anyC. userD. guestE. localip

Correct Answer: BCESection: (none)Explanation

Explanation/Reference:properly answered.

QUESTION 7What are aliases used for?


A. Improve controller performanceB. Simplify the configuration processC. Tie IP addresses to portsD. Assign rules to policiesE. Assign policies to roles

Correct Answer: BSection: (none)Explanation


QUESTION 8Which of the following firewall rules allows a user to initiate an ICMP session to other devices? (Choose two)

A. localip any svc-icmp permitB. user any svc-icmp permitC. user user svc-icmp permitD. any any svc-icmp permitE. mswitch any svc-icmp permit

Correct Answer: BDSection: (none)Explanation

Explanation/Reference:Real 9Aruba ACMP_6.3 Exam

Explanation:

QUESTION 9The Aruba Policy Enforcement Firewall (PEF-NG) module supports destination network address translation (dst-nat).

Which is the default use of this statement in an Aruba controller configuration?

A. Source the IP addresses of users to specific IP addressB. Redirect HTTP sessions to Captive PortalC. Redirect Access Points to another Aruba controllerD. Provide a telnet connection to the controllerE. Redirect a SSH session to terminate on the controller



QUESTION 10The Aruba Policy Enforcement Firewall (PEF) module supports source network address translation (src-nat).

Which is a use of this statement in an Aruba configuration?

A. Provide a single source IP address for users in a roleB. Redirect Captive Portal HTTP sessionsC. Redirect Access Points to another Aruba controllerD. Provide IP addresses to clientsE. Redirects clients to Aruba Firewall



QUESTION 11

The network administrator wishes to terminate the VPN encryption on the Aruba controller.

Real 10Aruba ACMP_6.3 ExamWhen writing a firewall rule to accomplish the task of automatically moving the VPN traffic for the wireless clients from a third party VPN concentrator to an Arubacontroller, which action needs to be configured in the rule?

A. redirect to IPSec GroupB. source NATC. destination NATD. redirect to tunnelE. redirect to GRE

Correct Answer: CSection: (none)Explanation


QUESTION 12Review the following truncated output from an Aruba controller for this item.

(example) #show rights logon

access-list List

----------------

Position Name Location

-------- ---- --------

1 logon-control

2 captiveportal

logon-control

-------------

Priority Source Destination Service Action

-------- ------ ----------- ------- ------

1 user any udp 68 deny

2 any any svc-icmp permit

3 any any svc-dns permit

Real 11Aruba ACMP_6.3 Exam4 any any svc-dhcp permit

5 any any svc-natt permit

captiveportal

-------------

Priority Source Destination Service Action

-------- ------ ----------- ------- ------

1 user controller svc-https dst-nat 8081

2 user any svc-http dst-nat 8080

3 user any svc-https dst-nat 8081

4 user any svc-http-proxy1 dst-nat 8088



Based on the above output from an Aruba controller, an unauthenticated user assigned to the logon role attempts to start an http session to IP address172.16.43.170.

What will happen?

A. the user's traffic will be passed to the IP address because of the policy statement:

user any svc-http dst-nat 8080B. the user's traffic will be passed to the IP address because of the policy statement:

user any svc-https dst-nat 8081C. the user's traffic will be passed to the IP address because of the policy statement:

user any svc-http-proxy1 dst-nat 8088D. the user will not reach the IP address because of the policy statement:

user any svc-http dst-nat 8080E. the user will not reach the IP address because of the implicit deny any any at the end of the policy.



QUESTION 13View the Server group screen shot above.


A company has provisioned the same VAP, AAA and SSID profiles at both its Miami and NY offices. This Server Group is applied for 802.1x authentication at bothlocations. The user's credentials are only found in the Miami Radius server "RadiusMiami". There is no Radius synchronization and both servers are reachable.What happens when the user attempts to authenticate?

A. The controller recognizes the users Domain and sends the authentication request directly to RadiusMiami.B. The request is initially sent to RadiusNY1 then RadiusNY1 redirects the controller to send the authentication request to RadiusMiamiC. RadiusNY1 receives the request and returns a deny. No other action is taken.D. RadiusNY1 receives the request and returns a deny. The authentication request will then be sent to RadiusMiami.E. The RadiusNY1 sends the request to RadiusMiami that replies to the controller



QUESTION 14View the Server group and User Roles screen shots above.

A user associated to an SSID with 802.1x using this server group. RadiusNY returned a standard radius attribute of filter-Id with a value of "employee". The userwas placed in the guest Role.

What statements below are correct? (Choose two)

A. The user was placed in the 802.1x authentication default Role guestB. The user was placed in the initial Role guestC. Role derivation failed because roles are case sensitiveD. Role derivation failed because the incorrect operation "value-of" was usedE. 802.1x authentication failed so the user was automatically placed in the guest Role

Correct Answer: ACSection: (none)Explanation


QUESTION 15View the Server group and User Roles screen shots above.


A user associated to an SSID with 802.1x using this server group. RadiusNY returned a standard radius attribute of filter-Id with a value of "employee".

What Role will the user get?

A. The User will get the Emp RoleB. The User will get the 802.1x authentication default RoleC. The User will get the employee RoleD. The User will get the Employee RoleE. The User will get the initial Role



QUESTION 16Which profiles are required in an AP Group to enable an SSID with VLAN 1, WPA2 and LMSIP? (Choose three)

A. Virtual-AP profileB. WLAN profileC. 802.1x authentication profileD. AP System ProfileE. SSID Profile

Correct Answer: ADESection: (none)Explanation


Explanation:

QUESTION 17A user connected to a Captive Portal VAP successfully. When the user opens their browser and tries to access their homepage, they get redirected as expected toanother URL on the Aruba Controller. However, they see an error message that web authentication has been disabled. What might be a cause of this?

A. Captive Portal has not been assigned in the SSID profile.

B. The Captive portal profile has not been assigned to the AAA profile.C. A server group has not been assigned to the captive portal profile.D. An initial role has not been assigned to the AAA profile.E. The Captive portal profile has not been assigned to the initial role.

Correct Answer: ESection: (none)Explanation

Explanation/Reference:real answer.

QUESTION 18Which of the following will accept named VLANs as a parameter? (Choose three)


A. Virtual AP profileB. User derivation rule for a single VLANC. Server derivation rule for a single VLAND. Server derivation rule for a VLAN PoolE. Access VLAN for a VLAN Pool

Correct Answer: ABCSection: (none)Explanation


QUESTION 19A customer has a remote AP deployment, where each remote AP has an IPSEC VPN tunnel with L2TP to the controller. 1 of the remote APs is stuck in the usertable and hasn't yet transitioned to the AP active table in the controller. The customer suspects that the AP is not setting up its VPN connection successfully. Which

of the following commands might be useful in troubleshooting this? (Choose three)


A. Logging level debugging security process localdbB. Logging level debugging security process l2tpC. Logging level debugging security process dot1xD. Logging level debugging security process cryptoE. Logging level debugging security process vpn

Correct Answer: ABDSection: (none)Explanation


QUESTION 20The screen captures below show the 802.1X authentication profile and AAA profile settings for a VAP.

If machine authentication fails and user authentication passes, which role will be assigned?


A. employeeB. guestC. contractorD. logonE. no role is assigned



QUESTION 21The screen captures above show the 802.1X authentication profile and AAA profile settings for a VAP.

Real 22Aruba ACMP_6.3 ExamIf machine authentication passes and user authentication fails, which role will be assigned?

A. employeeB. guestC. contractorD. logonE. no role is assigned



QUESTION 22

The screen captures above show the 802.1X authentication profile and AAA profile settings for a VAP.

Real 23Aruba ACMP_6.3 ExamIf machine authentication fails and user authentication fails, which role will be assigned?

A. EmployeeB. GuestC. Captive PortalD. LogonE. No role will be assigned



QUESTION 23

What can NOT be configured from the Aruba controller configuration wizards?

A. Controller IPB. Boot PartitionC. User firewall policy.D. User derivation rules.E. Radius Servers


Explanation/Reference:good answer.

QUESTION 24An administrator is setting up a factory default controller. No new AP groups were created. When adding a WLAN SSID in the Campus WLAN wizard what APgroup is available?

A. The air-monitors AP groupB. The logon AP groupC. The default AP groupD. The initial AP groupE. The Spectrum AP group




QUESTION 25The reusable Aruba Controller wizards are accessible in what way?

A. Only on startup through the CLI

B. Through the CLI, after the initial CLI wizard has been completedC. In the Web UI under maintenance.D. In the Web UI under configuration.E. Must be initialized from CLI first.



QUESTION 26The Contrtoller wizard enables which of the following controller clock configurations? (Choose three)


A. NTP to a time serverB. Set time zoneC. Daylight savings timeD. Only GMT can be configuredE. Manual configuration of date and time

Correct Answer: ABESection: (none)Explanation


QUESTION 27When configuring ports in the Controller wizard, which of the following are NOT configuration options? (Choose two)

A. Inter-VLAN routingB. SpeedC. TrustedD. LACPE. Trunk




QUESTION 28By default, which CLI based remote access method is enabled on Aruba controllers?

A. RSHB. TelnetC. SSHD. Telnet and SSHE. Telnet, SSH and RSH


Explanation/Reference:appropriate answer.

QUESTION 29An Aruba controller can be accessed with which CLI based remote access methods? (Choose two)

A. RSHB. TelnetC. SSH

D. SFTPE. SCP



QUESTION 30As an admin/root user, what other type of role-based management users can be created on Aruba controllers?

A. Auditing-compliance userB. AirWave management userC. Reporting Generation userD. Guest provisioning user


E. Maintenance user



QUESTION 31Which log type should be enabled to troubleshoot IPSec authentication issues on Aruba Controllers?

A. Security LogsB. Management LogsC. Wireless LogsD. IDS LogsE. System Logs

Correct Answer: ASection: (none)

Explanation

Explanation/Reference:fine answer.

QUESTION 32Exhibit:


Real 28Aruba ACMP_6.3 ExamReferring to the above screen capture, if an administrator desires to change a specific AP into a Spectrum Monitor without assigning the AP to a new group, whichmenus could be used?

A. Network > ControllerB. Wireless > AP ConfigurationC. Wireless > AP InstallationD. Advanced Services > WirelessE. Wizards > WIP Wizard



QUESTION 33A customer forgot all passwords for a controller. What method could you use to reset the passwords?

A. Telnet to the controller and login to the password recovery accountB. SSH to the controller and login to the password recovery accountC. Connect directly to the serial console and login to the password recovery accountD. Interrupt the boot process at CP-boot and select password recoveryE. Open the controller and press the reset switch



QUESTION 34With CPSec disabled, which tunnel protocol is used between APs and Controllers in an Aruba environment?


A. Basic IPB. GREC. IPinIPD. Mobile IPE. IPSec




QUESTION 35In an Aruba controller based system, the L3 mobility tunnel exists between the home agent and which other element?

A. the default gatewayB. the remote APC. the foreign agentD. the mobile nodeE. the foreign switch


Explanation/Reference:

Explanation:

QUESTION 36When an 802.11 client roams what device decides when to move the client to another AP?

A. Aruba APB. Aruba controllerC. ClientD. Radius ServerE. Router


Explanation/Reference:actual answer.

QUESTION 37Exhibit:


The above diagram has one master and three local controllers. AP1 GRE terminates on controller Local 1. All controllers are configured with the wireless userVLAN 201. A wireless user associates with AP 1. Only L2 mobility is enabled.

Which elements will know about this association?

A. Local 1 onlyB. Local 1 and the MasterC. Local 1 and Local 2 and the MasterD. Local 1 and AP1E. All Controllers

Correct Answer: BSection: (none)

Explanation


QUESTION 38Which command will show all client association history?

A. Aruba-6000# show mobile trail current (ip address)B. Aruba-6000# show ip mobile trail (ip address)C. Aruba-6000# show ap client status (mac address)D. Aruba-6000# show current client ip (ip address)E. Aruba-6000# show client ip (ip address) mobility




QUESTION 39With CPSec enabled, which tunnel protocol is used between APs and Controllers in an Aruba environment?

A. EAPB. SSHC. IPinIPD. Mobile IPE. IPSec



QUESTION 40By default, how long will an AP scan a single channel when ARM is enabled?

A. 80 millisecondsB. 90 millisecondsC. 100 millisecondsD. 110 millisecondsE. 200 milliseconds



QUESTION 41Which actions does ARM (Adaptive Radio Management) perform? (Choose two)

A. Allows controllers to provision the AP Radio typeB. Allows controllers to provision the best channel for APsC. Allows controllers to provision the best power setting for APsD. Allows controllers to provision allowed Radio bands Real 32

Aruba ACMP_6.3 ExamE. Allows controllers to provision lower power when unauthorized APs are detected


Explanation/Reference:reliable answer

QUESTION 42Which of the following metrics does the ARM feature use to calculate the optimal channel and power level for Access Points? (Choose two)

A. RF Spectrum IndexB. Priority Index

C. Interference IndexD. Coverage IndexE. Frequency Index

Correct Answer: CDSection: (none)Explanation


QUESTION 43How does the ARM Band Steering feature encourage 5GHz capable clients to move/connect to the 5GHz radios of Aruba APs?

A. ARM suppresses the probe response on the 2.4 GHz radioB. ARM utilizes third party software on the wireless clientsC. Current Wi-Fi chipset firmware supports this by defaultD. It's not possible the move clients to 5GHz radios when they can see both 2.4 and 5GHz APsE. ARM disables the 2.4Ghz radio for the specified client



QUESTION 44Which of the statements below are TRUE regarding ARM's Spectrum Load Balancing feature? (Choose two)


A. Available only on 5GHz radiosB. Disabled by defaultC. Balances client load across available channels/APsD. Enabled by defaultE. Available only on 2.4GHz radios



QUESTION 45What is the function of Band Steering?

A. Balancing clients across APs on different channels within the same bandB. Encourages clients, 5GHz capable, to connect on the 5GHz spectrumC. Coordinate access to the same channel across multiple APsD. Enables selection of 20 vs. 40 MHz mode of operation per bandE. Enables acceptable coverage index on both the "b/g" and "a" spectrums



QUESTION 46What are the Airtime Allocation Policy options for Airtime Fairness? (Choose three)

A. Default AccessB. Priority AccessC. Fair AccessD. Preferred AccessE. Distributed Access

Correct Answer: ACDSection: (none)Explanation

Explanation/Reference:right answer.

QUESTION 47Which of the following statements is true of Spectrum Mode?


A. No licenses are required to run an AP in Spectrum modeB. Spectrum mode can only be configured for one AP at a timeC. An AP can be in spectrum mode for both 2.4 and 5G bands at the same timeD. An AP can be placed in Spectrum Mode via the Spectrum ProfileE. Spectrum mode can be configured from the GUI under AP installation



QUESTION 48Which ARM feature addresses the issue of sticky clients by moving clients to associate to APs with better 802.11 signal quality?

A. Co-Channel interference mitigationB. Airtime FairnessC. ClientMatchD. Coordinated access to a single channelE. Band Steering



QUESTION 49Aruba Client Match does NOT use which of the following parameters to determine the best AP for a client connection? (Choose two)

A. Device typeB. LocationC. Signal to Noise RatioD. Access Point loadE. Spectrum Analysis



QUESTION 50Real 35Aruba ACMP_6.3 ExamWhich settings cannot be modified directly from a local controller?

A. Port VLAN settingB. Switch Time ZoneC. Port trustedD. RolesE. SNMP Enable Trap Generation


Explanation/Reference:properly answered.

QUESTION 51Masters communicate configuration information with locals using which tunnel type?

A. GREB. IP in IPC. Provision Tunnel ProtocolD. IPSecE. PPTP



QUESTION 52In the above screen capture:


The administrator notes that most of the configuration options are grayed out and have no action.

What is the cause of the problem?

A. attempting to make global changes on a Master ControllerB. attempting to make global changes on a Local ControllerC. this change can only be performed via the CLID. does not have the correct software license

E. there is an error in the configuration



QUESTION 53Exhibit:


Referring to the above screen capture, on which Controller can you create a vlan?

A. Controller 10.1.11.100 onlyB. Controller 10.1.11.101 and 10.254.1.3 onlyC. All three ControllersD. None of the ControllersE. Controller 10.254.1.101 only



QUESTION 54Exhibit:

Referring to the above screen capture, on which controller can you add an administrative user and assign a controller management role?

A. Controller 10.1.11.100 onlyB. Controller 10.1.11.101 and 10.254.1.3 onlyC. All three ControllersD. Must be done in the RADIUS serverE. Controller 10.254.1.101 only




QUESTION 55

Refer to the above screen capture.

By default, which controller's internal database will be used for user authentication?

A. Controller 10.1.11.100 onlyB. Controller 10.1.11.101 and 10.254.1.3 onlyC. All three ControllersD. You can't tell from this screenE. The Controller with the user session



QUESTION 56Real 44Aruba ACMP_6.3 ExamHow many Aruba controllers can be added to a single mobility domain?

A. 64 controllers of any typeB. 128 controllers supporting 2000 usersC. 256 controllers with no more than 1024 subnetsD. Controllers supporting up to 6000 AP'sE. There is no controller limit



QUESTION 57In a master-local controller scenario, where is the mobility domain defined?

A. the AP groupB. the master controllerC. the local controllerD. the master and the local controllersE. the master and the local controllers where roaming is needed


Explanation/Reference:genuine answer.

QUESTION 58A university has 2 departments. Department 1 has its own mobility domain with one controller. Department 2 has multiple controllers configured in a seconddomain. The university is planning on offering a new application and needs users to be able to roam between both mobility domains.

What is the best way to accomplish this?

A. The 2 existing domains should be left as they are. A 3rd mobility domain should then be created and all 3 controllers need to be added to itB. Merge the controllers into the same mobility domainC. The IP subnets of all controllers need to be configured to matchD. This cannot be accomplishedE. Create a new domain between a department 1 controller and one of the department 2 controllers


Correct Answer: BSection: (none)

Explanation


QUESTION 59A port firewall policy is applied to a trunk port that denies controller access. An "allow all" Vlan firewall policy is applied to VLAN 33 on the same port. A userconnected to VLAN 33 on that port attempts to gain access to the controller. Which of the following statements is true?

A. The Port policy is applied, therefore no controller accessB. The Vlan policy is applied, then the port policy, therefore no controller accessC. The Vlan policy is applied, therefore access to the controller is allowedD. You cannot place a firewall policy on a Ports Vlan when the Port already has a policy, therefore no controller accessE. When locally connected to a controller's port you always have controller access



QUESTION 60An access port has been placed in trusted mode. The Vlan on the port is in Untrusted mode.Which of the following statements is true?

A. The traffic is trusted since the port is trustedB. The traffic is untrusted since the VLAN is untrustedC. This is an invalid configuration, both must be set the sameD. You cannot set Vlans as trusted or untrustedE. Only traffic from that specific port is trusted, all other traffic is untrusted



QUESTION 61A wired device is connected to an untrusted port on a controller. How can a role be assigned to the device?


A. An initial Role can be assigned directly to the VLANB. Roles are assigned to devices connected to a trusted portC. A default Role can be directly assigned to an untrusted portD. Adding a wired AAA profile to a VLAN on the untrusted portE. The Role assigned to the untrusted port



QUESTION 62A port on a controller has been configured as untrusted. No wired access AAA profile or Global AAA profile is configured. When a user connects to that port whichof the following statements is true?

A. Since there is no wired access AAA profile, only port policies will be appliedB. The user will fall into the default wired access AAA profile and will be given the initial role.C. Since there is no wired access AAA profile or Global AAA profile the user will be given the logon role.D. When configuring the port as untrusted, an error message of "no wired access AAA profile exists" Therefore this is an invalid configuration.E. the user is denied all access automatically because no wired access AAA or Global AAA profile is assigned.


Explanation/Reference:actual answer.

QUESTION 63Which method can APs use to discover a controller?

A. DHCPB. Dynamic DNS (DDNS)C. PnPD. PAPIE. HTTPS




QUESTION 64Which of the following configurations can accept a VLAN pool? (Choose two)

A. Trunk native VLANB. Virtual AP profileC. User RoleD. Server derived roleE. FW Policies



QUESTION 65What does Aruba Layer 3 redundancy require to operate?

A. LMS-IPB. Backup LMS-IPC. VRRP

D. Backup AP groupE. ARM




QUESTION 66Exhibit:


In the diagram provided for this question, the client laptop is associated with the Aruba AP. The Aruba controller is configured to perform L2 switching for this SSID.

What will be the client laptop default gateway?

A. AB. B

C. CD. DE. E



QUESTION 67Real 54Aruba ACMP_6.3 ExamIn the diagram provided for this question, the Aruba controller terminates one end of a GRE tunnel that carries wireless user traffic.

Where does the other end terminate?

A. AB. BC. CD. DE. A or B



QUESTION 68In the above diagram, the system shows two Aruba access points and a wired user.


Which VLAN(s) do NOT need to be configured on link A between the L2 switch and router to support the wireless users?

A. 101 and 102B. 101 and 103C. 102 and 103D. only 101E. only 103

Correct Answer: A

Section: (none)Explanation


QUESTION 69In the above diagram, the system shows two Aruba access points.


Which VLANs must be configured on trunk link D between the router and Aruba controller to support wireless users when the controller is provisioned for L2operations?

A. 10, 101 and 102B. 101 and 102C. 101, 102 and 103D. 10, 101,102 and 103E. 10 and 103



QUESTION 70Exhibit:


Referring to the diagram provided for this question, if the Aruba controller is configured to perform L3 switching, what will be the wireless client laptop defaultgateway?

A. A

B. BC. CD. DE. E


Explanation/Reference:answer is suitable .

QUESTION 71When configuring Captive Portal, which protocols are supported when accessing the Captive Portal? (Choose two)

A. HTTPSB. VPNC. HTTPD. TELNETE. SSH




QUESTION 72When the controller is configured for Captive Portal and the user is only required to provide an email address for authentication, which option is configured in theGUI?

A. enable terminationB. enable guest logonC. enable user logonD. eap method

E. disable CP Login



QUESTION 73A user logged in with the Captive Portal settings shown in the above screen capture.


What does the user need to do to logout?

A. wait 30 minutes then logoutB. wait 60 minutes then logoutC. click Logout on the browser screenD. he cannot logoutE. wait 10 seconds for redirect



QUESTION 74Screenshots of the Captive Portal authentication profile and server group of a guest network are displayed above.


How was the user authenticated?

A. with a radius server called Radius01B. with the Internal databaseC. with a radius server called InternalD. with another form of authenticationE. user wasn't authenticated against any server




QUESTION 75Where should mobility domains be enabled in a network with 1 master, 1 backup master and 5 local controllers?

A. Only on the master controllerB. All the local controllers in the networkC. All the controllers where the client is allowed to roamD. Master and backup masterE. Only on the backup master



QUESTION 76What are two different methods of configuring AP redundancy between 2 local controllers? (Choose two)


A. Fast-FailoverB. Configure the locals as remote nodesC. Use named VLANSD. LMS and Backup LMS IPE. AP Redundancy can only be configured between a Master and Local


Explanation/Reference:sophisticated answer.

QUESTION 77

An Aruba 650 controller is functioning as a standby Master. How many APs can it control while in standby mode?

A. 0B. 16C. 24D. 128E. 256



Explanation:

QUESTION 78Aruba pair of 3200XM controllers are licensed to their maximum and are configured as a VRRP pair. Each controller terminates 24 APs. One of the controllers fails.How many of the APs from the failed controller can fail over to the remaining controller?

A. 8B. 16C. 32D. 48E. 96



QUESTION 79Which protocol does the Aruba controller utilize for controller redundancy?

A. HSRP

B. VRRPC. VPND. GREE. IP-IP



QUESTION 80With Fast-Failover disabled, to which IP address should the Aruba AP terminate its GRE tunnel for layer 2 controller redundancy to work and to support failover ofaccess points?

A. VRRP IP addressB. management IP of an Aruba controllerC. management IP of the backup Aruba controller


D. HSRP IP addressE. Loopback IP address of backup Aruba controller



QUESTION 81When an Aruba 6000 controller has two M3 modules installed, for which uses may the modules be used? (Choose two)

A. hot standby operationsB. VRRP backupC. higher AP density per switch chassisD. Active-Active masters

E. Active-Active master-backup



QUESTION 82Referring to the diagram provided for this question, an employee brought an unauthorized AP from home and attached the LAN port to the cubicle Ethernet port. AllAruba APs and AMs as well as the employee AP are in VLAN 80 and within RF range of each other. No traffic from the wired or wireless network has passedthrough the unauthorized AP yet, but the AP began wireless broadcasts.


How will the Aruba system initially classify the employee's non-Aruba AP?

A. a valid APB. an AMC. a Rogue APD. an interfering APE. a known interfering AP



QUESTION 83Referring to the diagram provided for this question, an employee brought an unauthorized AP from home and attached it to the cubicle Ethernet port as shown inthe diagram. The APs are in VLANs as shown in the diagram. Only AP1 is within RF range.


How will the Aruba controller classify this AP?

A. an APB. an AMC. a Rogue APD. an Interfering APE. a workstation



QUESTION 84Referring to the diagram provided for this question, an employee brought an unauthorized AP from home, but did not attach it to the LAN infrastructure. The APsare in the VLANs as shown in the diagram. Only AP1 is within RF range of the employee AP.


By default, how will the Aruba system classify the employee's AP?

A. an APB. an AMC. a Rogue APD. an Interfering APE. a valid workstation



QUESTION 85What can an AM do that an AP cannot do?

A. Detect rogue APsB. Detect an AP failureC. Scans all channels in under 1 minuteD. Detect interfering APsE. Scan all valid channels



Explanation:

QUESTION 86(group8) #show ap active

Active AP Table

---------------

Name Group IP Address 11g Clients 11g Ch/EIRP/MaxEIRP 11a Clients 11a Ch/EIRP/MaxEIRP

---- ----- ---------- --------- ------------------- ----------- -------------------

AP1 building1 10.1.80.150 0 AM 0 AM

AP2 building1 10.1.80.151 0 AM 0 AM

A user called technical support because they cannot see any of their APs in building one. You perform the "show" command as illustrated above.

What can you conclude about these two APs from this output?

A. the GRE for the APs terminate on two different controllers: 10.1.80.150 and 10.1.80.151B. the system will not function because there is no building1 group definedC. the building1 APs will not accept any user connectionsD. the user needs to configure his client to use the b/g bandE. the user needs to configure his client to use the a band



QUESTION 87Exhibit:


Based on the above screen capture for Interfering APs, what can you conclude?

A. The APs must be connected to the Aruba network.B. The APs are classified as interfering because they are all transmitting on channel 6.C. There must not be any evidence that the APs are attached to the wired corporate network.D. These APs are classified as interfering because they are not Aruba APs.E. They are classified as interfering because they are running in g mode.



QUESTION 88

As illustrated in the above diagram and screen capture, a wireless hacker injects messages into your network to detach a client from your Aruba AP.

Real 69Aruba ACMP_6.3 ExamWhat action should you take to identify and prevent the Intruder from connecting to your system? (Choose two)

A. Enable Detect disconnect Station AttackB. Enable Spoofed Deauth BlacklistC. Take no action as there is no protection against this form of attackD. Take no action as the Aruba system ignores this attack because it is against the clientE. Enable Detect EAP rate Anomaly

Correct Answer: ABSection: (none)Explanation


QUESTION 89(group8) #show ap arm history ap-name AP1

Interface :wifi0

ARM History

-----------

Time of Change Old Channel New Channel Old Power New Power Reason

-------------- ----------- ----------- --------- --------- ------

2010-10-28 07:58:53 157+ 149+ 21 21 I

2010-10-28 07:52:06 149+ 157+ 21 21 M

2010-10-28 07:16:59 157+ 149+ 21 21 I

Interface :wifi1

ARM History

-----------

Time of Change Old Channel New Channel Old Power New Power Reason

-------------- ----------- ----------- --------- --------- ------

2010-10-28 08:52:53 6 1 21 21 I

Referring to the output above. What can you conclude about AP1?


A. This device is scanning channels.B. This device is unstable because the channel assignment changed.C. The device changed channels recently.D. The device changed channels and power levels recently.E. The device is transmitting at maximum power levels.



QUESTION 90An Aruba controller is configured with the correct IP address and gateway information and is connected to the corporate LAN via a core layer 2 switch. ControlPlane Security is not enabled on the network. An access point is provisioned with AP name and group and connected to a different Layer 2 switch on the corporateLAN that has IP connectivity to the core layer 2 switch. The AP powers on and layer 2 connects to the network, but the wireless radios do not power on.

Which could cause this condition? (Choose two)

A. the layer 2 switches have ACLs that block GRE trafficB. the layer 2 switches are configured to block IPSec trafficC. a DHCP server is not configured for the segment to which the AP is connectedD. the AP's mac address needs to be configured in the Aruba controller whitelist.E. the AP and controller are in different subnets



QUESTION 91In the diagram provided for this question, four buildings are identified on a college campus. Most of the wireless LAN traffic will be from students accessing theinternet.


According to Aruba best practices, which building is the best location to install the Aruba mobility controller?

A. data centerB. dormitoryC. server farmD. libraryE. 3rd party site



QUESTION 92Referring to the diagram provided for this question, representing an office wireless LAN deployment, there will be approximately 250 users in the offices section ofthe building. All Switches are setup as L3 routers.


According to Aruba best practice, which network device is the best choice for the wireless clients' default gateway?

A. device 'A'B. device 'B'C. device 'C'D. device 'D'E. device 'C or D'

Correct Answer: B


Explanation/Reference:exact answer.

QUESTION 93One hundred (100) additional APs were deployed in an existing network. But some APs are not able to connect to the lms-ip address, even though all of the APsbelong to the same AP group. Which of the following are NOT potential causes? (Choose two)


A. The problem APs are not getting an IP address.B. The problem APs have the wrong lms-ip address setting.C. There is a firewall between the problem APs and the controller blocking PAPI.D. The controller does not support that many APs in a single AP-Group.E. There are not enough AP licenses to support the additional quantity of APs.


Correct Answer: BDSection: (none)Explanation


QUESTION 94IEEE 802.11r provides support for which of the following:

A. radio measurements within a WLANB. radio measurement within an ESSC. fast roaming within an ESS

D. fast roaming within a BSSE. roaming across controllers



QUESTION 95If a Remote AP (RAP) is attempting to contact a controller that is behind a NAT device what protocol must be allowed through the NAT/Firewall?

A. PAPIB. NATTC. IPSecD. SSHE. GRE



QUESTION 96Which of the following are NOT valid RAP forwarding modes? (Choose two)

A. TunnelB. BridgeC. Split-TunnelD. Backup


E. Standard

Correct Answer: DESection: (none)

Explanation


QUESTION 97Which of the following are valid RAP operating modes?

A. Always, Backup, Standard, PersistentB. Always, Backup, Tunnel, PersistentC. Always, Hotel-Connect, Tunnel, StandardD. Backup, Hotel-Connect, Standard, PersistentE. Backup, Normal, Tunnel, Always


Explanation/Reference:best asnwer.

QUESTION 98When configuring split tunnel mode on a Remote AP (RAP) where is the routing function for the split tunnel defined?

A. On the IP routing tab in the configuration screen.B. On the AP provisioning screen.C. In the RAP static routing tablesD. In the Firewall policyE. In the RAP whitelist



QUESTION 99When does a RAP's backup SSID begin broadcasting?

A. When the GRE tunnel to the controller is established.B. When the IPSec tunnel to the controller is established.


C. When the controller cannot be reached with PAPID. When bridging is required for guest users.E. When the controller cannot be reached with SSL



QUESTION 100A Remote AP provisioned in "Split-Tunnel" Forwarding mode has which characteristic?

A. Local traffic first goes to the controller and is then spilt back to the local network.B. Traffic is IPSec encrypted before it is sent to the controller.C. The user role must have a "Permit" statement in order to locally bridge the traffic.D. The user role must have a "route dst-nat" statement to locally bridge the traffic.E. The RAP uses PAPI to send data traffic to the controller.



QUESTION 101A Remote AP was properly functioning before losing it's internet connection and now cannot communicate with the controller. What SSID is the AP broadcasting?

A. The SSID in Operational mode Always and Forwarding mode BackupB. The SSID in Operational mode Split Tunnel and Forwarding mode BridgeC. The SSID in Operational mode Always and Forwarding mode Tunnel

D. The SSID in Operational mode Standard and Forwarding mode TunnelE. The SSID in Operational mode Persistent and Forwarding mode Bridge



QUESTION 102A Remote AP provisioned with an SSID in "Bridged" forwarding mode has which one of the following characteristics?


A. The client obtains its IP address from the controller.B. The client's default gateway must be the controller.C. The client traffic is forwarded through a GRE tunnel to the controller.D. The client's default gateway may be the Access Point or a local gateway.E. The client's authentication must be 802.1X.



QUESTION 103An AP 105 was converted into a RAP. The RAP can authenticate its IPSec tunnel to a controller using which of the following methods? (Choose two)

A. 802.1X/EAP authenticationB. Captive Portal authenticationC. IP address authenticationD. Username/Password authentication.E. Certificate/MAC address authentication.

Correct Answer: DE



QUESTION 104Which of the following describes a Remote AP provisioned in "Split-Tunnel" Forwarding mode?


A. Local user traffic first goes to the controller and is then spilt back to the local network.B. All data and control traffic goes to the controller unsecured.C. The user role must have a "Permit" statement in order to locally bridge the traffic.D. The user role must have a "route src-nat" statement to locally bridge the traffic.E. The RAP uses PAPI to send data traffic to the controller.


Explanation/Reference:selected answer is accurate.

QUESTION 105A Remote AP provisioned in "Split-Tunnel" Forwarding mode has which of the following

Real 80Aruba ACMP_6.3 Examcharacteristics?

A. Local traffic first goes to the controller and is then spilt back to the local network.B. User Traffic is CPSec encrypted before it is sent to the controller.

C. The user role must have a "Permit" statement in order to locally bridge the traffic.D. The user role must have a "permit dst-nat" statement to locally bridge the traffic.E. The RAP uses UDP 4500 to send traffic to the controller.



QUESTION 106What is the purpose of Mesh Clusters?

A. To separate Mesh points from Mesh Portals.B. To ensure that mesh APs with the same VAPs are not in the same cluster.C. To define a group of mesh APs that create mesh links with each other.D. To cluster mesh APs of the same model together.E. To enable mesh APs to join the nearest mesh portal cluster.



QUESTION 107A company purchased an indoor mesh deployment using the 620 controller and the AP 105 models, where 5 APs will be deployed on a floor to provide wirelessinternet access for users. Users may open VPN tunnels using software clients over the wireless network to a 3rd party VPN concentrator overseas. The companywants to limit wireless user access to TCP traffic locally and VPN traffic overseas.

In addition to the base AOS, which licenses will be necessary for this deployment?

A. VPN, PEF-NGB. AP Capacity, PEF-NGC. AP Capacity, PEF-NG, VPND. AP Capacity

E. PEF-NG, PEF-VReal 81Aruba ACMP_6.3 Exam


Explanation/Reference:appropriate answer.

QUESTION 108When deploying Remote Mesh Portals, what is one of the purposes of the Mesh Private VLAN?

A. To separate wireless user traffic coming from mesh networks from non-mesh networksB. To tag mesh wireless user traffic on a particular APC. To allow Mesh Points to form private vlan networks with certain usersD. To tag control plane traffic from Mesh points to the controllerE. To tag clients high priority traffic



QUESTION 109How does an Aruba infrastructure calculate a wireless device's location?

A. GPSB. RF FingerprintingC. RSSI triangulationD. TDOAE. LBS


Explanation/Reference:Real 82

QUESTION 110Which dual radio access point models support concurrent operations in the 2.4Ghz band as well as the 5Ghz band? (Choose three)

A. AP-92B. AP-93C. AP-105D. AP-224E. AP-135

Correct Answer: CDESection: (none)Explanation



QUESTION 111Which of the following APs do NOT support dual radio operations? (Choose two)

A. AP 93B. AP 105C. RAP 3WND. AP 224E. AP 135



QUESTION 112Centralized licensing is not in use on an Aruba based network which has a Master and three local controllers. No APs terminate on the Master controller. Roles andFirewall policies need to be created and applied, hence PEF-NG license is required

On which controller should the license be installed?

A. Only the master controller since role and firewall policies are created here.B. Only the local controllers since firewall policies are applied hereC. The master and all three local controllersD. This isn't the correct license for this purpose, use PEF-VPN licenseE. This is not needed because PEF-NG is part of base OS



QUESTION 113What information do you need to generate a feature license key for an Aruba controller?

A. The controller's MAC address and the feature description.B. Controller's MAC address and the certificate numberC. Controller's Serial Number and the feature descriptionD. Controller's Serial Number and the certificate number Real 3

Aruba ACMP_6.3 ExamE. Controller's MAC address and Serial Number



QUESTION 114What are the PEF-NG license limits based on?

A. Number of APsB. One license per controllerC. Number of usersD. Number of local controllersE. Master Controller total user count


Explanation/Reference:suitable answer.

QUESTION 115Which of the following licenses are consumed by Mesh APs advertising an SSIDs?

A. AP licenseB. Mesh licenseC. PEF-V licenseD. No license is requiredE. RAP License



QUESTION 116The permanent licenses on the controller will be deleted with the use of which command?

A. Delete licenseB. Write eraseC. Licenses cannot be deleted once activated


D. Write erase all

E. Reboot delete all



QUESTION 117A network administrator wants to terminate VPN sessions on a local controller in the DMZ. Which statement is true about the PEF-VPN license?

A. It is only applied to the master controllerB. It is only applied to the DMZ controller.C. It is based on the number of APsD. One license is needed on the master and the DMZ localE. It is distributed by the license server as needed



QUESTION 118Which of the following parameters can be specified in a rule for AP classification? (Choose three)


A. SSID of an APB. Number of clients connected to an AP.C. SNR of an AP.

D. Operating mode of an APE. Discovering APs

Correct Answer: ACESection: (none)Explanation


QUESTION 119Which of the following functions can be configured in the Controller WIP wizard? (Choose three)

A. Configure APs as Air MonitorsB. Configure rules for AP classification.C. Configure preset levels for intrusion detectionD. Blacklisting Rules for clientsE. Identify encryption method used in your network.

Correct Answer: BCESection: (none)Explanation


QUESTION 120A client device associates with an SSID provisioned with 802.1X authentication. The client is set

Real 71Aruba ACMP_6.3 Examfor PEAP authentication. EAP termination (AAA Fastconnect) is disabled on the controller. But the client continuously cycles through the authentication process.Which of the following could cause this? (Choose two)

A. The client is provisioned with the wrong EAP type.B. The client has an expired or revoked server certificate.C. The DHCP server is not enabled.D. The VLAN is missing for the SSID.E. The controller does not support PEAP in this mode.



QUESTION 121A client device associates with an SSID provisioned with 802.1X authentication. The client is set for LEAP authentication. EAP termination (AAA Fastconnect) isenabled on the controller. But the client continuously cycles through the authentication process. Which of the following could cause this?

A. The Radius server is rejecting the client credentials.B. The client has an expired or revoked server certificate.C. The DHCP server is not enabled.D. The VLAN is missing for the SSID.E. The controller does not support LEAP in this mode.


Explanation/Reference:accurate answer.

QUESTION 122A client attaches to a secure jack interface set to untrusted. But when the client tries to access the captive portal page, the following message appears, "WebAuthentication is not enabled." What might be wrong?

A. The client has the browser provisioned with proxy settings.B. The controller port needs to be set to trusted.C. A "aaa" profile needs to be selected on the Wired Access page.D. A Captive Portal profile needs to be assigned to the initial role.E. Web Authentication cannot be used in this way.


Correct Answer: DSection: (none)

Explanation


QUESTION 123Which command, when executed on a master controller, will show the APs connected to all controllers?

A. show stm connectivityB. show ap activeC. show ap databaseD. show ap bss-tableE. show ap controller-lms



QUESTION 124Which of the following commands is most useful in showing the traffic of an individual user?

A. show datapath session tableB. show acl hitsC. show rightsD. show firewallE. show traffic client



QUESTION 125When direct consoled to an AP, what is the command sequence to factory default the AP and re- bootstrap?

A. setenv bootstat initB. setenv master init, bootC. purge, save, bootD. init, save, bootE. print, purge, boot


Explanation/Reference:perfectly answered.

QUESTION 126What settings need to be changed on a factory default AP in order for it to use ADP to discover the Aruba Controller?

A. DNS of the controllerB. Static routeC. AP groupD. enable multicastE. no changes needed




QUESTION 127As illustrated in the above diagram, a company has two campus locations and a building headquarters all located in different cities.

Following best practices, what would be the best way to construct mobility domains for the company?

A. Buildings (1, 2) in one domain and Buildings (3, 4, 5, 6) in one domainB. Buildings (1, 2) in one domain, Building (3) in one domain, and Buildings (4, 5, 6) in one domainC. Buildings (1, 2, 4, 5, 6) in one domain and Building (3) in one domainD. Buildings (1, 2, 3, 4, 5, 6) in one domainE. Buildings (1) in one domain building (4) in one domain



QUESTION 128When APs boot up, in which order do they discover a controller?

A. DNS, DHCP, ADP multicast, ADP unicast, staticB. static, DNS, DHCP, ADP broadcast, ADP multicastC. static, DHCP, ADP multicast, ADP broadcast, DNSD. static, DHCP, DNS, ADP multicast, ADP broadcastE. DNS, static, ADP multicast, ADP broadcast



QUESTION 129An AP is not communicating with the controller. Upon investigation you find that the AP is not discovering its controller through DNS. Instead, it received a DHCPreply with option 43 specifying the SIP server's IP address. How do you resolve this problem?

A. Statically configure the AP to ignore Option 43B. Remove the option 43 configuration on the DHCP serverC. Statically configure the AP to only use DNS resolution and not other dynamic discovery methodsD. After failing option 43 the AP should have proceeded with ADP, therefore the AP is faulty and needs to be replacedE. The AP should be purged



QUESTION 130How is an AP redirected to a Local controller after DNS resolution returns the Master's IP address?

A. Master looks at the AP-Group and CONTROLLER-IP attributesB. Master looks at the AP-Group and LMS-IP attributesC. In the AP-provisioning screen, the LMS-IP attribute must be setD. The AP must be statically configured to find the local controllerE. In the AP-provisioning screen, set the CONTROLLER-IP attribute Real 48

Aruba ACMP_6.3 Exam



QUESTION 131An AP was configured and assigned to an AP group then powered off for over a week. When the AP is redeployed, what previous configuration will it retain?

A. It's AP name and AP GroupB. It's Serial NumberC. The controller's IP addressD. After a few days all configurations are lostE. The controller IP address and the AP Group


Explanation/Reference:correct answer.

QUESTION 132A 3600 controller has 64 PEF-NG license, 128 AP licenses and 1 RFProtect license. How many AP's can terminate on the controller?


A. 1 Campus APsB. 64 Campus APsC. 128 Remote APsD. 256 Remote APsE. 512 Remote APs



QUESTION 133A 3200 controller has 16 AP licenses,16 PEF-NG licenses, 16 RFProtect licenses. There are 10 Campus APs terminating on the controller. How many remote AP'scan terminate on the controller?

A. 6Real 49Aruba ACMP_6.3 Exam

B. 12C. 16D. 24E. 32



Explanation:

QUESTION 134Centralized licensing is not enabled in a network of 1 Master and 2 Local controllers, what should be the license count on all controllers to terminate 8 APs on eachLocal controller and support Local redundancy?

A. 16 AP license on all controllersB. 8 AP license on Master and 16 AP license on both localsC. 8 AP license on all controllersD. 1 AP license on Master and 16 AP license on both localsE. 16 AP licenses on the Locals



QUESTION 135An 7240 controller is Licensed for 560 APs. The controller has 500 Campus APs terminating on the controller. How many Remote APs can terminate on thiscontroller?

A. 12B. 24C. 48D. 60E. 120


Explanation/Reference:best answer.

QUESTION 136Real 50Aruba ACMP_6.3 Exam

An Aruba Controller is configured with VLAN 1,5, 200, and 4095. All VLANs have IP addresses assigned. Which is the default management VLAN on the Arubacontroller?

A. VLAN 5B. VLAN 1C. VLAN 200D. None, it must be definedE. VLAN 4095



QUESTION 137Which of the following statements is true?

A. Aruba Campus APs must be physically attached to the Aruba Controller.B. Aruba Campus APs must be in the same broadcast domain as the Controller.C. Aruba Campus APs can be in different subnets from the Controller.D. Aruba Campus APs must be physically attached to the same Layer 3 switch.E. Aruba Campus APs can be connected directly to the public internet.



QUESTION 138Exhibit:


Referring to the diagram provided for this question, in which locations must you define the new data VLANs for wireless client traffic? (Choose two)

A. in all L2 switches where an Aruba AP is physically connectedB. in all APs and the L2 switches to which they are connectedC. in the Aruba controller and the router it's connected to in an L2 deploymentD. in the routers and switches where the APs are physically connectedE. only on the Aruba controller in an L3 deployment

Correct Answer: CESection: (none)Explanation


QUESTION 139A controller is provisioned in L3 Mode for Wireless Users. What must be configured on the controller to enable DHCP requests to an external DHCP server?

A. an IP helper commandB. the IP address of the DNS serverC. the IP address of the APsD. the subnet address of the DHCP serverE. the DHCP server IPSEC Key




QUESTION 140Which parameter(s) does a Master controller use to determine where a provisioned AP should terminate its GRE tunnel?

A. the IP address of the APB. the MAC address of the APC. the IP address of the switch nearest to the APD. the name and group settings of the APE. the VLAN the AP is attached to



QUESTION 141What is the best practice regarding licensing for a backup master to support Master Redundancy in a network without centralized licensing?

A. Backup master only requires the AP licenseB. Supported limits and installed licenses should be the same on primary master and backup MasterC. Licenses are pushed from the primary to the backup Master along with the configuration

D. The Backup Master does not require licenses to support master redundancyE. On the backup only one license of each typeis needed.



QUESTION 142Which of the following licenses can be included in the licensing pool for centralized licensing? (Choose three)


A. Factory default licensesB. PEFNG licenseC. Evaluation licensesD. RFProtect licenseE. PEFV license

Correct Answer: BCDSection: (none)Explanation


QUESTION 143By default Centralized licensing messages between master controllers are sent _______________.

A. In the clear unencryptedB. Using CPSecC. Using IPSec site to site VPN tunnelsD. Encrypted using GREE. PAPI

Correct Answer: A


Explanation/Reference:reliable answer.

QUESTION 144Which of the following will occur if a master license server fails with no standby server present? (Choose two)

A. Local controllers licenses will continue to be valid for 30 daysB. Local controllers will immediately remove all installed licensesC. No licenses will be sent to any new controllers that come onlineD. All licenses go back into the pool for redistributionE. A Local Controller elects itself master license server



QUESTION 145Real 6Aruba ACMP_6.3 ExamWhich may be applied directly to an VLAN interface? (Choose three)


A. Access List (ACL)B. Firewall PolicyC. RolesD. AAA profiles

E. RF Plan Map

Correct Answer: ABDSection: (none)Explanation


QUESTION 146When creating a firewall rule on an Aruba controller, which parameter is optional?

A. DestinationB. ServiceC. SourceD. LogE. Action



QUESTION 147An administrator creates a WLAN with an unmodified default AAA profile. What is the default role the user is placed in?

A. default-logonB. logonC. guest-logonD. default-apE. AP-Role



Explanation:


QUESTION 148An Aruba based network has a Master and four local controllers deployed. But one of the locals, a new installation, is not seen by the Master. What might bewrong? (Choose two)

A. PAPI is not enabled on the local controller.B. The master controller can only support three local controllers.C. IPSec is blocked by the internal network between the local and the master controllers.


D. The passphrase does not match on the master and local controllers.E. GRE is blocked between the master and local controllers.



QUESTION 149Exhibit:


Referring to the above screen capture, on which controller can you modify APs configuration to enable ARM?

A. Controller 10.1.11.100 onlyB. Controller 10.1.11.101 and 10.254.1.3 onlyC. All three ControllersD. None of the ControllersE. On Controllers where ARM is enabled



QUESTION 150With CPSec disabled, Aruba access points are Layer 3 connected to controllers using which protocol?

A. 802.1qB. LWAPPC. PPTPD. GREE. HTTPs



QUESTION 151With CPSec disabled, which encryption protocol does a tunnel mode campus AP use on client traffic?

A. TKIP and AESB. It is provisioned by the AdministratorC. WEP and AESD. WEP, TKIP, and AES

E. No encryption is used




QUESTION 152In a campus environment, where are encryption keys sent or stored when users roam between tunneled mode APs on the same controller using 802.1X?

A. sent to the new AP via GREB. sent to the new AP via IPSecC. stored on the controllerD. stored on the RADIUS serverE. original AP sends keys to new AP



QUESTION 153In the diagram provided for this question, the wireless user's laptop is associated with an Aruba AP in tunnel forwarding mode. The AP terminates on the localcontroller.

When the client transmits, where will the 802.11 headers be removed?


A. APB. L2 SwitchC. RouterD. ControllerE. Internet


Explanation/Reference:answer i supdated.

QUESTION 154When configuring a server group containing 3 servers, a customer chooses 'fail through mode'. What other configuration option has to be enabled on the controllerfor this to work with 802.1x authentication?

A. Machine authenticationB. EAP TerminationC. Server group fall through modeD. MAC authenticationE. Round robin or top down mode



QUESTION 155A campus AP has been provisioned with a VAP in bridge forwarding and standard operation modes. Which of the following authentication types are supported?(Choose two)

A. 802.1X authenticationB. Open System authenticationC. Local authenticationD. Captive portal authenticationE. VPN authentication



Explanation:


QUESTION 156Which method is NOT supported to provision an Aruba campus AP?

A. Telnet directly to APB. SSH to the AP's controllerC. Web interface to the AP's controllerD. Console to APE. CLI on controller



QUESTION 157Refer to the following configuration segment for this item.

Real 12Aruba ACMP_6.3 Examip access-list session anewone

user network 172.16.1.0 255.255.255.0 any permit

user host 172.16.1.1 any deny

user any any permit

An administrator wants users to have access to all destinations except 172.16.1.1. Based on the above Aruba Mobility Controller configuration segment, whichstatements best describe this policy? (Choose two)

A. The rule user host 172.16.1.1 any deny is redundant because of the implicit deny all at the end.B. The rule user network 172.16.1.0 255.255.255.0 any permit is redundant.C. The two rules user network 172.16.1.0 255.255.255.0 any permit and user host 172.16.1.1 any deny need to be re-sequenced.

D. The last statement user any any permit is not requiredE. The last statement should be any any any deny



QUESTION 158Refer to the following configuration segment for this item.

netdestination "internal"

no invert

network 172.16.43.0 255.255.255.0 position 1

range 172.16.11.0 172.16.11.16 position 2

!

ip access-list session "My-Policy"

alias "user" alias "internal" service_any permit queue low

!

A user frame is evaluated against this firewall policy with the following attributes:

Real 13Aruba ACMP_6.3 ExamSource IP: 172.17.49.3 Destination IP: 10.100.86.37 Destination Port: 80

Referring to the above file segment, how will the frame be handled by this firewall policy?

A. The frame will be dropped because of the implicit deny all at the end of the netdestination definition.B. The frame will be dropped because of the implicit deny all at the end of the firewall policy.C. The frame will be forwarded because of the implicit permit all at the end of the firewall policy.D. The frame will be passed because there is no service specified in the firewall policy.

E. The frame will be dropped because there is no service specified in the firewall policy.



QUESTION 159ip access-list session anewone


user any any permit

host 10.1.1.1 host 10.2.2.2 any deny

A user sends a frame with the following attributes:

Source IP: 10.1.1.1 Destination IP: 10.2.2.2 Destination Port: 25

Based on the above Mobility Controller configuration file segment, what will this policy do with the user frame?

A. The frame is discarded because of the implicit deny all at the end of the policy.B. The frame is discarded because of the statement:

user host 10.1.1.1 host 10.2.2.2 deny.C. The frame is accepted because of the statement:

user any any permit.D. The frame is accepted because of the statement:

user network 10.1.1.0 255.255.255.0 any permit.E. This is not a valid policy.



Explanation:

QUESTION 160ip access-list session anewone


user host 10.1.1.1 any deny

user any any permit

Referring to the above portion of a Mobility Controller configuration file, what can you conclude? (Choose two)

A. This is a session firewall policy.B. This is an extended Access Control List (ACL).C. Any traffic going to destination 10.1.1.1 will be denied.D. Any traffic going to destination 10.2.2.2 will be denied.E. Any traffic going to destination 172.16.100.100 will be permitted.

Correct Answer: AESection: (none)Explanation


QUESTION 161Which of these are NOT a client attribute that can be configured in user derivation rules?

A. MAC addressB. DHCP option valueC. BSSIDD. Filter IDE. encryption



QUESTION 162Real 15Aruba ACMP_6.3 ExamWhat are the types of user derivation rules that can be applied to a user? (Choose two)

A. SSIDB. MACC. VLAND. RoleE. AP



QUESTION 163Which is a Device Specific Attribute that can be evaluated in a user derivation rule?

A. user login nameB. authentication serverC. location by AP NameD. controller Loopback addressE. controller IP



QUESTION 164

Which match condition can be used by a server derivation rule? (Choose two)

A. greater thanB. less thanC. inverse ofD. containsE. equals

Correct Answer: DESection: (none)Explanation


QUESTION 165Real 16Aruba ACMP_6.3 ExamAn administrator wants to assign a VLAN to a user based upon the authentication process using Vendor Specific Attributes (VSA). Where are Aruba VendorSpecific Attribute (VSA) values provisioned?

A. controllerB. clientC. RADIUS serverD. Internal user databaseE. Option 60 of DHCP reply




Documents

Aruba ACMP 6.3 Aruba Certified Mobility Professional 6.3 ... · It guided me step by step through the course. After studying for a month using it I achieved the highest in the whole