Upload
denbe-santos
View
248
Download
1
Embed Size (px)
Citation preview
7/29/2019 Armored Riot Control
1/12
Based on a Ford
F-750
ARMORED RIOT CONTROL WATER CANNON TRUCK
7/29/2019 Armored Riot Control
2/12
Page 1Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
Engine:
Transmission:
Power:
Tires:
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51
Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
FORD F-750 (Basic Specs)
5.9 L. Cummins Diesel
5-Speed Automatic
215 HP @2300 RPM 520 lb/ft @1600RPMTires:
Goodyear 10R22.5 With Run Flat Inserts
Height:
Length:
Wheelbase:
Width:
117 in. (298 cm.)
312 in. (792 cm.)
158 in. (401 cm.)
93 in. (236 cm.)
http://www.alpineco.com/mailto:[email protected]:[email protected]:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
3/12
Page 2Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
ARMOR SPECIFICATIONS
Protection on all sides to Level A10
Protection against high power rifles such as: 7.62x39, 5.56x45, .03-06 and 7.62x51 rounds
OPAQUE (AR 500 Steel): 0.50 in thick
TRANSPARENT (Glass/Polycarbonate): 55 mm thick
Seating- two seats up front, bench seating for 4 in rear, 2" padded seat and backs
Special LED Red and Blue lights
White LED dome lights for the Interior
Armored Dual battery compartment
Running boards with grab handles
Rear door opening 6', 8" long and 33" wide
Insulation on all walls and ceiling (2")
Recording equipment for all cameras
Under seat compartments
3 Outside storage cabinets
Removable Plow Control
Revolving Water Cannon
Revolving Camera on rooftop
2 Gun Ports on each side of the front cabin
P/A System with siren
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51
Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
http://www.alpineco.com/mailto:[email protected]:[email protected]:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
4/12
Page 3Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
INSTRUCTIONS
Operations of Stryker
Using the remote control, turn on the light by depressing the on/off button
With the 4-way arrows on the remote control, rotate your light to the desired location.
Depending upon conditions, the wireless remote may be used up to 100 feet from the Stryker.
The speed of the light rotation can be controlled by depressing the fast/slow button one timeand by depressing it again to restore the original speed.
The spotlight should not be turned on when the snap on lens (rockguard) is attached.
BULB REPLACEMENT
The GolightStryker utilizes a Philips9011 bulb
IMPORTANT INFORMATION
This GolightStryker is a radio transmitter and receiver operating at 433mhz. Whenever the light
is on, the internally mounted antenna sends out and receives radio frequency (RF) energy.
PROGRAMMABLE REMOTE INSTRUCTIONS
The GolightStryker is controlled with a programmable remote with 6561 different channels.This feature allows you freedom to change the channel
selection, & the receiver relearns the new selection.
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51
Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
GO LIGHTS
* Click here to view PDF link
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/go-light-stryker_inst.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/go-light-stryker_inst.pdfmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
5/12
Page 4Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
RED
BLUE STROBE LIGHTS
Double, Red/Blue Strobe, Lighter Plug-in. The RVM directional warning device combines the best
warning signal & easiest installation
Inside the dashboard the ON/OFF Strobe Lights Button
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51
Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
RED/BLUE LIGHTS
http://www.alpineco.com/mailto:[email protected]:[email protected]:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
6/12Page 5Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
TOUCH PAD PLOW CONTROL
Plow Is made out of 1/4'" armor steel.
Intuitive design with large illuminated raised rubber indicator arrows for ease of use.
Convenient indicator lights make it simple to see the status of the plow.
Only Up and Down Arrows.
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
PLOW CONTROLS
http://www.alpineco.com/mailto:[email protected]:[email protected]:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
7/12Page 6Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
PUBLIC ADRESS SYSTEM WITH MULTI-MODE SIREN
Two manual functions allow for additional siren tone choices when you need it the most.
PTT (push to talk) switch on microphone overrides all siren functions.
Combination On/Off and horn ring transfer switch.
Pre-wired unidirectional microphone.
Optional plug-in microphone with volume control knob.
Adjustable preset microphone volume.
Adjustable preset radio repeat volume.
Input polarity protection.
Output short circuit protection.
External spade-type fuse.
Bi-polarity horn/ring control activation.
"Aux Enable" activates
Siren tones via input (slide switch, power controls or relay-to-ground connection).
Quick disconnect plug for ease of service or replacement.
Adjustable bail bracket allows the mounting of the siren in a variety of positions.
Complements all Whelen's under dash products.
Backward compatible to the original 295HF100 and
WS2100 Series connector.
Optional 24 volt DC model available, contact factory.
DIMENSIONS
Height: 63mmx Width: 152mmx Depth: 138mm
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
CONTROL BOX
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/pa-system.pdfmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
8/12Page 7Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
COLOR CCD IR BULLET CAMERA #1, #3, #4
Camera #1 Right Side
Camera #3 Left Side
Camera #4 Rear View
Night Vision, High Resolution
COLOR CCD IR BULLET CAMERA #2
Camera #2 Front View
Mini 10x weatherproof PTZ Camera
WTX-1200A KEYBOARD CONTROLS
Pan/Tilt Operating Di : 4,000ft (1,092m)
on 24 AWG wire
3-Axis, vector solving, with twisting,
return-to-center head
THIN FILM TRANSISTOR (TFT)
LIQUID CRYSTAL DISPLAY (LCD) MONITOR
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
CAMERA SYSTEM
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/bullet-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/mini-ptz-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/control-joystick.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/control-joystick.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/mini-ptz-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/bullet-camera.pdfmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
9/12Page 8Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
WATER CANNON
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/8494-Sidewinder-Instructions.pdfmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
10/12Page 9Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
CONTROL BOX
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
11/12Page 10Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
HOW TO OPERATE WATER CANNON CONTROLS
1.
Turn on Button on Box Control
2. Lower pressure
3. Start Engine Pump
4. Hold button to add pressure till desired distance and pressure shows
5. Use joystick to move cannon
6.
To use Dye Push trigger on joystick
7.
Push Button to Spread/Fan Effect on Nozzle
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
CONTROL BOX
1
2
3
4
5
6
7
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlhttp://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlmailto:[email protected]://www.alpineco.com/7/29/2019 Armored Riot Control
12/12Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]
COMPOSITE RUN FLAT (CRF) INSTALLATION
Ensure the CRF properly fits the wheel before mounting the tire
Clean wheel and install metal valve supplied.
Use a soft cloth or brush to apply supplied lubricant to evenly inside crown of the tire, around entire circumference.
With flanges and washers facing up, position CRF arcs against wheel and confirm they are properly mated to wheel profile.
Install bolts to ensure CRF is secure to the wheel drop center. Bolts should be tightened to 30 +/- 5 ft.lbs
If needed place the steel mounting rods in the holes on each side of the CRF joint.
Slip adjustment band over rods and pull outward to bring arcs together.
Attempt to rotate CRF around wheel to assure it is snug.
For additional tightness, unfasten set screw on washer, rotate one or both washers 180 as needed. Re-install set screw.
INSTALLATION IN TIRE
Insert arcs into the tire with the flanges and washers facing up.
Apply supplied loctite to one bolt. Connect arcs loosely with one bolt
Fit inboard tire bead on wheel and allow CRF to move into wheels drop center
With outboard tire bead above the wheel flange, place steel mounting rods vertically in holes on each side of CRF joint.
Rotate CRF until the joint is centered over the valve
Slip adjustment band over mounting rods. Laterally spread the rods at top closing the CRF.
Apply loctite on the remaining bolt and tighten ALL bolts to 30 +/- 5 ft.lbs
Secure mechanical lock over all connection bolts. Attached with #2 phillips head screw driver.
Mount outer tire bead and inflate to manufacturers recommended pressure for load carried.
Page 11
Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)
to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds
ARMORED RIOT CONTROL / WATER CANNON TRUCK
RUN FLAT INSTALLATION
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/HutchinsonCRFInstall.pdfmailto:[email protected]://www.alpineco.com/