Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
ARCH 3691 Advanced Design &
Building Information Modeling
CREATING DIAMOND SHAPED PANELS (CHIPS OUTSULATION)
Manipulating existing panels and arraying them along the facade of your building.
Professor Paul C. King, RA, AIA, ARA [email protected] [email protected]
MEISHA GUILD [email protected]
1.25
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Open up a new curtain wall family
CREATING DIAMOND SHAPED PANELS
A.
B.
C. D.
E.
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Manipulating/Editing panels
CREATING DIAMOND SHAPED PANELS
NOTE: REMEMBER TO SET PLANE TO MATCH THE DIRECTION YOU’RE DRAWING IN
Use reference lines to create a center line across the panel. (Reference lines are green)
Create center point
Create perpendicular lines across panel
Line tool Point tool
A.
B.
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Create vertical line from center point
CREATING DIAMOND SHAPED PANELS
Set vertical plane Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
A. B.
C.
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Repeat vertical line and arc steps
CREATING DIAMOND SHAPED PANELS
NOTE: TRY TO GET THE 2 ARCS AS CLOSE TO THE CORNER AS POSSIBLE
You should have 3 arcs in total, all going in the same direction
A.
B.
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Create new form w/ Mass
CREATING DIAMOND SHAPED PANELS
NOTE: THE PANEL IS CREATED WITH TWO PARTS
A. Select center arc and one of the smaller corner arcs, then click create form
B. The first half of the panel is now created Now create the other half by selecting the center arc and the other smaller arc
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second
half of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Load panel into project
A. Now that the panel is created, you can load it into your project
B. Choose the project that you want the panel to be loaded into.
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to suggest
the direction/orientation of the panel on the wall
Prof. Paul C. King Copyright © 2013
ARCH 3691
Advanced Design & Building Information
Modeling
Applying panels to walls A. After loading the panel into your project you can apply it to your walls. Go to components and select your panel
B. Select four points on your wall to orient your panel in the direction you wish.
4 points
C. Copy panels across your wall
Open up a new curtain wall family
Project Browser Open Family Curtain panel by pattern Rhomboid surface
Manipulating/Editing panels Use reference lines to
create perpendicular lines across the panel
Create center point
Create a vertical reference line from center point
Create an arc using corner points and the vertical line as the height of the arc
Repeat vertical line and arc steps on opposite ends of the panel.
Create new form w/ mass Select arcs for first half of
mass Select arcs for second half
of mass Load panel into project
Applying panels to walls
• Components • Select panel • Click four points to
suggest the direction/orientation of the panel on the wall