AR150&200 Quick Start Guide(03) (1)

8/17/2019 AR150&200 Quick Start Guide(03) (1)

1/42

Huawei AR150&200 Series Enterprise Routers

Quick Start Guide

Issue 03

Date 2012-06-10

HUAWEI TECHNOLOGIES CO., LTD.


2/42

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice

The purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within the

purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd. Address: Huawei Industrial Base

Bantian, LonggangShenzhen 518129People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Issue 03 (2012-06-10) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

i

http://www.huawei.com/


3/42

About This Document

Intended AudienceThis document provides an overall description of the AR150/200, details about each chassis and

board, cables available to the device, lists of components and basic configuration.

This document is intended for:

l Network planning engineersl Hardware installation engineersl Commissioning engineersl On-site maintenance engineersl System maintenance engineers

Symbol ConventionsThe symbols that may be found in this document are defined as follows.

Symbol Description

DANGER

Indicates a hazard with a high level of risk, which if notavoided, will result in death or serious injury.

WARNING

Indicates a hazard with a medium or low level of risk, whichif not avoided, could result in minor or moderate injury.

CAUTION

Indicates a potentially hazardous situation, which if notavoided, could result in equipment damage, data loss,

performance degradation, or unexpected results.

TIP Indicates a tip that may help you solve a problem or savetime.

NOTE Provides additional information to emphasize or supplementimportant points of the main text.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide About This Document


ii


4/42

Change HistoryChanges between document issues are cumulative. Therefore, the latest document issue containsall the changes in previous issues.

Changes in Issue 03 (2012-06-10)

Based on 02 (2012-04-20), this issue has the following updates:

l AR156l AR158E

Changes in Issue 02 (2012-04-20)

Based on 01 (2011-12-30), this issue has the following updates:

lThe power outage survival description is added to the rear panel of AR207V&AR207V-P.

l AR207G-HSPA+7.

Changes in Issue 01 (2011-12-30)Initial commercial release.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide About This Document


iii


5/42

Contents

About This Document.....................................................................................................................ii

1 AR150/200 Overview.....................................................................................................................11.1 Naming Rule.......................................................................................................................................................2

1.2 Device Structure.................................................................................................................................................31.3 Indicator Description..........................................................................................................................................6

1.4 Physical Specifications.....................................................................................................................................11

2 Product Installation.....................................................................................................................132.1 Ins tallation Preparations...................................................................................................................................14

2.2 Installing the Device.........................................................................................................................................15

2.3 Connecting the Device......................................................................................................................................20

2.4 Powering on the Device....................................................................................................................................23

3 Logging In to the Router............................................................................................................253.1 Logging In to the Router Through the Web Network Management System....................................................26

3.2 Logging In to the Router Through the Console Port........................................................................................27

3.3 Logging In to the Router Using Telnet.............................................................................................................29

4 Connecting to the Internet.........................................................................................................304.1 Going On line Using a Static IP Address..........................................................................................................31

4.2 Going On line Using a Dynamic IP Address.....................................................................................................33

5 How to Obtai n Documentation and Technical Support......................................................36

6 FAQs..... ..........................................................................................................................................37

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide Contents


iv


6/42

1 AR150/200 OverviewAbout This Chapter

This section describes the naming rule, appearance and structure, indicators, and physicalspecifications of the AR150/200.

1.1 Naming RuleThis section describes the meanings of the AR150/200 names.

1.2 Device StructureThis section describes the structure of the AR150/200.

1.3 Indicator DescriptionThis section describes the indicators on the AR150/200 front panel.

1.4 Physical SpecificationsThis section describes the physical specifications and system configuration of the AR150/200.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 1 AR150/200 Overview


1


7/42

1.1 Naming Rule

This section describes the meanings of the AR150/200 names.Figure 1-1 shows the AR150/200 naming rule.

Figure 1-1 AR150/200 naming rule

AR B1 B2 B3 B4 C1 -D1Example:

AR 207 V - P AR 207 G - HSPA+7

12

Table 1-1 explains the AR150/200 naming rule.

Table 1-1 AR150/200 naming rule

Field DescriptionB1 0 (AR150/200): indicates a low-end case-shaped product.

B2 B2: Indicates the hardware difference. Selected from 1 and 2. A larger value indicates higher performance.

B3 B3: Indicates the product level, ranging from 0 to 5.l AR150: fixed as 5.l AR200: fixed as 0.

B4 B4 Indicates the fixed upstream interface.

l 1: FEl 6: ADSL-Bl 7: ADSL-Al 8: G.SHDSL

C1 C1: Composed of one to four upper-case letters, indicating value-added functions.l W: WLANl V: Voicel G: 3G

l E: Enhanced edition



2


8/42

Field Description

D1 D1: Indicates the function differences.l A: AC power supply (Default configurations can be omitted)

l D: DC power supplyl HSPA+7: WCDMAl P: PoE

1.2 Device StructureThis section describes the structure of the AR150/200.

Figure 1-2 and Figure 1-3 show the AR150/200 models.

Figure 1-2 AR150 models

1 2 4 53

76

8

1

2

4 53

76

8

1

2

4 5

76

3 8

1

2

4 5

76

3 8

AR150 Series

ProductSeries Model

WANPort

LANPort

Appearance Remark

AR151

1 FE 4 FE

AR157

4 FE1ADSL2+

AnnexA/M

4 FE

4 FE

AR

156

AR158E

1ADSL2+

AnnexB

1G.SHDSL

ATM andEFM

modes



3


9/42

Figure 1-3 AR200 non-3G models

ProductSeries Model

WANPort

LANPort

Appearance Remark

AR201

1 FE 8 FE

AR206

AR207

8 FE

AR

207V8 FE

AR207V-P

8 FE

AR208E

8 FE

AR200 Series

1 2 4 53

76

1

2

4 53

76

1

2

4 53

76

1

2

4 53

76

9 10

1

2

4 53

76

9 10 11

1

2

4 53

76

8 FE

1G.SHDSL

ATM andEFM

modes

1ADSL2+

AnnexA/M

1ADSL2+

AnnexA/M

Voiceports:

4FXS+1FXOSurvivable remote

sitetelephony

(SRST)

Voiceports:

4FXS+1FXPoE

Survivableremote

sitetelephony

(SRST)

1ADSL2+

AnnexB

1ADSL2+

AnnexA/M

8

8

8

8

8

8



4


10/42

Figure 1-4 AR200 3G models

13

1 4 53

2 6 7

12

13

AR200 Series

ProductSeries Model

WANPort

LANPort

Appearance Remark

1ADSL2+

AnnexA/M

AR207G

-HSP A+7

8 FE

1: CON/AUX port 2: WAN port

l AR151, AR201: FEl AR156, AR157, AR206,

AR207, AR207V,AR207V-P, AR207G-HSPA+7: ADSL

l AR158E, AR208E:G.SHDSL

3: LAN FE port

l AR151, AR156, AR157,AR158E: 4 FE ports

l AR201. AR206, AR207,AR207V, AR207V-P,AR208E, AR207G-HSPA+7: 8 FE ports

NOTE

FE0 can be used as a WAN port

so that double WAN ports can be provided.

4: RESET

CAUTION

The Reset button is used for resetting the device manually.l Press and hold down:

Restore the FactorySettings.

l Press: Reset the system.

Resetting the device will causeservice interruption; therefore,confirm the action before youreset the device.

5: DC power jack

NOTE

The AR150/200 is powered by a12 V external power adapter .

6: Silkscreen

7: Ground screw 8: cable retention clip 9: Four FXS ports

10: FXO port 11: PoE port 12: SIM card slot

13: 3G antenna

Table 1-2 describes the attributes of G.SHDSL interfaces.



5


11/42

Table 1-2 Attributes of G.SHDSL interfaces

Attribute Description

Standards compliance G.991.2 Annex A and Annex B

Transmission rate 5.696 Mbit/s per pair

Transmission distance 3 km

1.3 Indicator DescriptionThis section describes the indicators on the AR150/200 front panel.

IndicatorsThe indicators on the AR150/200 front panels vary according to the product models. Table1-3 lists the indicator differences.

Table 1-3 Indicator differences

Difference Description

WAN port silkscreen l AR151 and AR201: WAN FEl AR156, AR157, AR206, AR207, AR207V, AR207V-P, and

AR207G-HSPA+7: ADSLl

AR158E, AR208E: G.SHDSLLAN ports l AR151,AR156, AR157 and AR158E: Four, numbered LAN0

to LAN3l AR201, AR206, AR207, AR207V, AR207V-P, AR208E, and

AR207G-HSPA+7: Eight, numbered LAN0 to LAN7

Voice port indicator l AR207V and AR207V-P: Five, numbered FXS0 to FXS3,FXO

l Other models: None

3G port indicator l An AR207G-HSPA+7 provides three indicators thatindicating 3G, 2G, and WWAN.

l Other models of the AR150/200 provide no 3G port indicator.



6


12/42

Indicator DescriptionNOTE

l The front panels of AR151, AR156, AR157 and AR158E are the same except for the WAN portindicator silkscreen. Figure 1-5 shows the AR158E appearance.

l Compared with AR207V, AR207V-P has a PoE port indicator. Figure 1-6 shows the AR207V-Pappearance.

l The front panels of AR201, AR206, AR207, and AR208E are the same except for the WAN portindicator silkscreen. Figure 1-7 shows the AR208E appearance.

Figure 1-5 AR158E front panel

2 3 4 5 6 7 8

10

Figure 1-6 AR207V-P front panel

2 3 4 5 6 7 8

10

91



7


13/42

Figure 1-7 AR208E front panel

2 3 4 5 6 7 8

10

Figure 1-8 describes indicators on the AR207G-HSPA+7 front panel.

Figure 1-8 Indicators on the AR207G-HSPA+7 front panel

2 3 4 5 6 7 8

10

11 12 13

Table 1-4 Indicator description

Number

Indicator Color Description

1 PoE Green If the indicator is steady on, the PoE power supplyis normal.

If the indicator is off, no PoE power supply isavailable.



8


14/42


15/42

Number

Indicator Color Description

If the indicator blinks green, the LAN port istransmitting or receiving data.

If the indicator is off, no link is connected to theLAN port.

9 FXS0-FXS3 Green If the indicator is steady on, the FXS channel is being occupied by a call.

If the indicator is off, the FXS channel is idle.

FXO Green If the indicator is steady on, the FXO channel is being occupied by a call.

If the indicator is off, the FXO channel is idle.

10 USB port N/A

11 3G Green If the indicator is steady on, the 3G signal strengthis high.

If the indicator blinks once every 2s, the 3G signalstrength is poor.

If the indicator blinks once every 0.25s, the 3Gsignal strength is medium.

12 2G Green If the indicator is steady on, the 2G signal strengthis high.

If the indicator blinks once every 2s, the 2G signalstrength is poor.

If the indicator blinks once every 0.25s, the 2Gsignal strength is medium.

13 WWAN Green If the indicator is steady on, the 3G or 2G servicehas been connected or activated.

If the indicator is blinking, 3G or 2G service datais being transmitted or received on the port.

If the indicator is off, the 3G or 2G service hasnot been connected or activated.

NOTE

l Number 1: Only AR207V-P has this indicator.

l Number 7: The WAN port indicators have different silkscreens (such as WAN FE, ADSL, andG.SHDSL).

l Number 8: FE0 can be used as a WAN port so that double WAN ports can be provided.

l Number 9: Only the AR207V and AR207V-P provide this indicator.

l Numbers 11, 12 and 13: Only the AR207G-HSPA+7 provides these indicators.



10


16/42

1.4 Physical SpecificationsThis section describes the physical specifications and system configuration of the AR150/200.

Table 1-5 Physical specifications

Item Description

Dimensions (width x depth x height) Without rack-mounting ears installed: 300.0 mm x216.4 mm x 44.0 mm

With rack-mounting ears installed: 482.6 mm x216.4 mm x 44.0 mm

Maximum power consumption l AR151: 11.6Wl

AR156: 16.1Wl AR157: 15.2Wl AR158E: 14.7Wl AR201: 12.3Wl AR206: 16.1Wl AR207: 16.1Wl AR207V: 22.8Wl AR207V-P: 22.6Wl AR208E: 14.7W

l AR207G-HSPA+7: 17.1W

Weight 2.2 kg

Operating temperature 0°C-40°C

Relative humidity 5% RH to 90% RH, non-condensing

Altitude 0 m-3000 m

AC inputvoltage

Rated voltage 100 V AC-240 V AC, 50/60 Hz

Maximum voltagerange

90 V AC-264 V AC, 47/63 Hz

Table 1-6 System configuration

Model Processor Memory Flash Memory

AR151 2-core: 533 MHz 512 MB 512 MB

AR156 2-core: 533 MHz 512 MB 512 MB

AR157 2-core: 533 MHz 512 MB 512 MB

AR158E 2-core: 533 MHz 512 MB 512 MB



11


17/42

Model Processor Memory Flash Memory

AR201 2-core: 533 MHz 512 MB 512 MB

AR206 2-core: 533 MHz 512 MB 512 MB

AR207 2-core: 533 MHz 512 MB 512 MB

AR207V 2-core: 533 MHz 512 MB 512 MB

AR207V-P 2-core: 533 MHz 512 MB 512 MB

AR208E 2-core: 533 MHz 512 MB 512 MB

AR207G-HSPA+7 2-core: 533 MHz 512 MB 512 MB



12


18/42

2 Product InstallationAbout This Chapter

This section describes the method of installing and connectingAR150/200 series products.

2.1 Installation PreparationsThis section lists the tools and accessories for installing the AR150/200.

2.2 Installing the DeviceThis section describes AR150/200 installation scenarios and installation methods.

2.3 Connecting the DeviceThis section describes how to connect AR150/200 series products.

2.4 Powering on the DeviceThis section provides the checklist used t o check the AR150/200 before powering on it.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 2 Product Installation


13


19/42

2.1 Installation PreparationsThis section lists the tools and accessories for installing the AR150/200.

Tools

Claw hammer Utility knife COAX crimping tool

Diagonal pliers RJ45 crimping tool Wire stripper

Network cable tester Multimeter Measuring tape

Ladder Hammer drill Vacuum cleaner

ESD wrist strap Level Floating nut mounting bar

Flat-head screwdriver Philips screwdriver Marker pen

Accessories

Rubber pad Floating nut M4 screw: fixes brackets tochassis

M6 screw: fixes chassis intocabinet Bracket Ground cable

Remote Antenna



14


20/42

2.2 Installing the DeviceThis section describes AR150/200 installation scenarios and installation methods.

NOTE

The installation scenarios and installation methods of all AR150/200 series products are the same. Thissection uses AR207G-HSPA+7 as an example.

The antenna interfaces on a AR207G-HSPA+7 can connect to whip antennas and remote antennas.l Whip antennas are directly installed on an AR router and are recommended when a router is desk

installed or wall mounted.l Indoor remote antennas have a 3 m long feed line. Indoor remote antennas are recommended when

an AR router is installed in a cabinet or rack, Indoor remote antennas need to be ordered separatelyif needed.

Placing Chassis on the Desk1. Before placing the AR150/200 on the desk, attach rubber pads onto each of the four recessed

corner areas on the bottom of the chassis.

2. AR207G-HSPA+7 needs two whip antennas, which must be vertical to the desktop. (Onlyapplies to 3G models).



15


21/42

Wall-Mounting the Chassis

CAUTIONl When wall-mounting the AR150/200, do not attach rubber pads to the chassis. If the rubber

pads have been attached, remove them.l It is inconvenient to connect ground cables and network cables after mounting the

AR150/200 chassis on the wall. Therefore, it is recommended that you connect cables beforemounting the chassis on the wall. If the chassis has been mounted on the wall, hold the chassiswhen connecting cables, preventing it from being detached from the wall. For the method of connecting cables, see 2.3 Connecting the Device .

l When connecting cables, do not make the front plastic panel of the chassis touch the groundto avoid damage.

l

It is recommended that you wall-mount the AR150/200 with its front panel (with indicators)facing up and its rear panel (with interfaces) facing down.l Use a ladder when mounting the chassis on the wall.

1. Use the template on the last page to mark the location for the two mounting screws and theupper, left, and right edges of the chassis on the wall.

2. The diameter of the mounting screws is 4 mm. Choose an appropriate drill bit accordingto the diameter of the mounting screws. Hammer the hollow wall anchors into the drilledholes. Screw the mounting screws into the wall anchors using a screwdriver. Leave thescrews protruding 2 mm from the wall.



16


22/42

3. Mount the chassis by aligning the mounting brackets on the back of the AR150/200 usingmounting screws. Install the antennas of the 3G model downwards and vertical to theground.

4. Connect the power adapter. Place the power adapter on a nearby horizontal surface, but donot hang it under the equipment.



17


23/42

Installing the Chassis in a Cabinet or Rack

CAUTION

l When installing the AR150/200 in a cabinet or rack, do not attach rubber pads to the chassis.If the rubber pads have been attached, remove them.

l The guide rails or trays are not necessary for the installation in a cabinet or rack because theAR150/200 chassis can be fixed by rack-mounting brackets. Customers need to buy the rack-mounting brackets.

l It is recommended that you install the AR150/200 with its front panel (providing indicators)facing inside and its rear panel (providing interfaces) facing outside. The rack-mounting

brackets are installed at the sides of the rear panel (providing interfaces) facing outside.l Ensure that the air exhaust vent is not obstructed in any way. Otherwise, the chassis may

overheat.

1. Install two rack-mounting brackets. It is recommended that you install the rack-mounting brackets close to the rear panel (providing interfaces). Install two rack-mounting brackets.It is recommended that you install the rack-mounting brackets close to the rear panel(providing interfaces).



18


24/42

2. Install two floating nuts on each side of the rack. The AR150/200 chassis is 1 U high. Themounting holes located on the rack-mounting brackets will be fixed to two mounting holeson the rack.

Floating nutmounting bar

3. Raise and hold the chassis by hands and move the chassis into the cabinet. Insert the panelscrews into the below floating nuts and keep a 2 mm space between the screws and mounting

bar. Insert the rack-mounting ear pre-installation holes into the space. Fix panel screws intotwo floating nuts and keep 2 mm space between the screw and mounting rail. Raise and

hold the chassis and move the chassis into the cabinet or rack, and place mounting holesof rack-mounting brackets into the space between the floating nut and panel screw.

2mm

4. Hold the chassis with one hand while using the other hand to secure the lower panel screwand then the upper one with a screwdriver.



19


25/42

5. You are advised to install antennas on top of the cabinet or chassis vertical to the ground.This step applies only to 3G models. Install the remote antenna on the 3G main interface.It is recommended that you place the antenna on the top of the cabinet or rack and is in thedirection vertical to the ground. This step is applicable to 3G models.

Remote Antenna

2.3 Connecting the DeviceThis section describes how to connect AR150/200 series products.

AR150/200 series of non-3G models have the same connection modes. The AR207V is used asan example.



20


26/42

Figure 2-1 AR207V connection

4

1

2

5

6

a b

1 2 3

4 5 6

7 8 9

* 0 #

3

AR150/200 series of 3G models have the same connection modes. The AR207G-HSPA+7 isused as an example.



21


27/42

Figure 2-2 AR207G-HSPA+7 connection

7

7

8

1: Console cable

l The 8-pin RJ45 connector is inserted into the console port (CON/AUX port) of theAR150/200.

l The DB9 male connector is connected to the maintenance terminal, such as a computer.

2: WAN port cable that connects the AR150/200 to the upper-layer network

l On an AR151 or AR201, the WAN port is an FE port, which connects to an network cablewith RJ45 connectors.

l On an AR156, AR157, AR206, AR207, AR207V, AR207V-P or AR207G-HSPA+7, theWAN port is an ADSL port, which connects to a cable with RJ11 connectors.

l On an AR158E or AR208E, the WAN port is a G.SHDSL port, which connects to a cablewith RJ45 connectors.

3: Voice port cable, which is connected to a telephone with a telephone line (RJ11 connectors).



22


28/42

4: LAN port cable, which is connected to a computer with a network cable (RJ45 connectors).

5: Ground cable. The M4 connector is connected to the AR150/200 and the M6 connector isconnected to ground. The cable is in yellow and green.

l When the AR150/200 is placed on the desktop or installed in a cabinet/rack, the groundcable is connected facing downwards, as shown in Figure 2-1 a. The ground cable cannotinterfere with other devices in the cabinet/rack.

l When the AR150/200 is wall mounted, the ground cable is connected facing left, as shownin Figure 2-1 b.

6: external power adapter, which is connected to the AC power supply to output DC power tothe device.

Power adapter output power:l

AR150 & AR200 series: 36 WNOTE

The AC power cable must be secured using a latch.

7: A whip antenna, which is installed on a 3G interface to transmit and receive 3G signals.

8: A SIM card, which is installed in the SIM card slot of a device to allow the device to connectto a 3G network.

2.4 Powering on the DeviceThis section provides the checklist used to check the AR150/200 before powering on it.

Checklist

No. Item Method

1 The power cables and ground cables are copper wires, andare not spliced or damaged. The cables are safelyconnected and in compliance with standards.

View

2 The power cables and ground cables are connected safely.The spring washers of the ground cable terminals are onthe flat washer.

View

3 All signal cables to be deployed pass the continuity check. Measure

4 No signal cables are near the cabinet's heat vents. View

5 The bent part of signal cables cannot be too tight. View

6 The cables in the cabinet are not crossed and the cablesoutside the cabinet are bundled.

View

7 Both ends of signal cables are clearly labeled and the labeltext is in the same direction.

View



23


29/42

No. Item Method

8 Newly added devices will not cause a loop on the network.For example, a newly added device cannot be connectedto another device using two links.

View thenetworkingdiagram

Checking the AR150/200 After Power-onNOTE

l After powering on the AR150/200, view the PWR and SYS indicators. All the AR150/200 series havethe same PWR indicators and SYS indicators.

l For details about the indicators on AR150/200, see 1.3 Indicator Description .

CAUTION

Do not frequently power on and off the device.

21

After powering on the AR150/200, check the following indicators.

No. Silkscreen Status

1 PWR If the indicator is green, the system power supply is normal.

2 SYS If the indicator blinks green once every 2s (0.5 Hz), the systemis running properly.



24


30/42

3 Logging In to the RouterAbout This Chapter

After the router is powered on, you can log in to the router.

3.1 Logging In to the Router Through the Web Network Management SystemThis section describes how to log in to the router through the web network management system.

3.2 Logging In to the Router Through the Console PortThis section describes how to log in to the router through the console port.

3.3 Logging In to the Router Using Telnet

This section describes how to log in to the router using Telnet.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 3 Logging In to the Router


25


31/42


32/42

3.2 Logging In to the Router Through the Console PortThis section describes how to log in to the router through the console port.

Procedure

Step 1 Connect the router to a PC using a Console Cable. Connect the RJ45 connector of the cable tothe console port of the router, and connect the DB9 connector to the serial port of the PC.

Step 2 Run the terminal emulation program on the PC. For example, to open the HyperTerminal of Windows XP on the PC, choose Start > Programs > Accessories > Communications >HyperTerminal . Enter the name of the new connection in the Name text box and click OK , asshown in Figure 3-2 .

Figure 3-2 Creating a connection

Step 3 Select the console port used and click OK , as shown in Figure 3-3 .



27


33/42

Figure 3-3 Selecting the console port

Step 4 Click Restore Defaults and click OK , as shown in Figure 3-4 .

Figure 3-4 Setting communication parameters



28


34/42

Step 5 Press Enter on the subsequent dialog boxes until the command line prompt of the user view,such as , is displayed.

You can run commands to configure the router. Enter a question mark (?) to see a list of availablecommands.

----End

3.3 Logging In to the Router Using TelnetThis section describes how to log in to the router using Telnet.

Procedure

Step 1 Connect a PC to any LAN port of the router with a network cable.

Step 2 Configure an IP address for the PC. The IP address must be on the network segment192.168.1.0/24, but cannot be 192.168.1.1.

After the configuration is complete, run the ping 192.168.1.1 command on the PC to check whether the router can be pinged successfully. If the ping operation succeeds, the connectionhas been set up successfully. If the ping operation fails, the connection failed to be established.Check whether the network cable is working properly. If not, replace the network cable.

Step 3 Access the command line window on the PC. For example, if the PC runs Windows XP, chooseStart > Run and enter cmd in the displayed dialog box.

Step 4 Run the telnet 192.168.1.1 command to log in to the router.

Step 5 Enter the default user name and password admin . If the user interface is displayed, you loggedin successfully.

When you log in for the first time, the following information is displayed:

Username: admin

Password:

----End



29


35/42

4 Connecting to the InternetAbout This Chapter

This section describes how to enable users to connect to the Internet through the router.

Select the network access mode based on the link type of uplink physical interfaces.

4.1 Going Online Using a Static IP AddressThis section describes how to go online using a static IP address allocated by a carrier.

4.2 Going Online Using a Dynamic IP AddressThis section describes how to go online using a dynamic IP address.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 4 Connecting to the Internet


30


36/42

4.1 Going Online Using a Static IP AddressThis section describes how to go online using a static IP address allocated by a carrier.

Networking RequirementsAs shown in Figure 4-1 , the carrier allocates fixed IP addresses to users for Internet access.Configure the Router using the web network management system so that LAN users can accessthe Internet.

Figure 4-1 Going online using a static IP address

Eth0/0/8

Router

Eth0/0/1I n t e r n e

tI n t e r n e t

I n t e r n e tI n t e r n e tLAN

Procedure

Step 1 Click Wizard in the navigation tree to open the following page.

Click Next to access the Configure the Broadband Connection page.

Step 2 Set broadband connection parameters.

Set Next to Static IP .

NOTE

The IP address, subnet mask, default gateway, and the primary DNS server are provided by the carrier.



31


37/42

Click Next to access the Configure the LAN page.

Step 3 Set LAN access parameters.NOTE

By default, Layer 2 Ethernet interfaces of the AR150 or AR200 join VLAN 1 and the IP address of VLANIF1 is 192.168.1.1/24.



32


38/42

Click Next to access the Finish Configuration Wizard page.

Step 4 Confirm the configurations.

View the configurations on the Finish Configuration Wizard page. To confirm theconfigurations, click Finish . To modify the configurations, click Previous . If you quit the wizardwithout clicking Finish , the configurations will not take effect.

----End

4.2 Going Online Using a Dynamic IP Address

This section describes how to go online using a dynamic IP address.

Networking RequirementsAs shown in Figure 4-2 , RouterA functions as the enterprise egress gateway. The uplink interface obtains a dynamic IP address to connect to the Internet. Configure RouterA using theweb network management system so that LAN users can access the Internet.



33


39/42


40/42

Click Next to access the Configure the LAN page.

Step 3 Set LAN access parameters.NOTE

By default, Layer 2 Ethernet interfaces of the AR150 or AR200 join VLAN 1 and the IP address of VLANIF1 is 192.168.1.1/24.

Click Next to access the Finish Configuration Wizard page.

Step 4 Confirm the configurations.

View the configurations on the Finish Configuration Wizard page. To confirm theconfigurations, click Finish . To modify the configurations, click Previous . If you quit the wizardwithout clicking Finish , the configurations will not take effect.

----End



35


41/42

5 How to Obtain Documentation andTechnical Support

This section describes how to obtain documentation and technical support.

Obtaining DocumentationVisit http://support.huawei.com and choose Data Communication > Product > Router >

Prodcut Type > Product Manual to obtain corresponding documentation.

NOTE

You can select different values of Product Type . For example, to query the AR200 documentation, selectAR150&200 .

The web site provides files in .pdf and .hdx format. You can view a single manual in web formatonline. Equipment users can browse the Hedex package after logging to the web site. Select therequired documentation.

It is recommended that you use the email address to request the equipment user name and password. If you have any questions, contact the Huawei technical personnel.

Obtaining Huawei Technical Support

If you have trouble in locating or rectifying fau lts during maintenance or troubleshooting byfollowing instructions in this document, contact the Huawei customer service center (CSC) for help.

l Email: [email protected]

You can also visit http://support.huawei.com , click Contact Us in the lower area of the page,and select the country to obtain contact information about Huawei local office.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 5 How to Obtain Documentation and Technical Support


36

http://support.huawei.com/supporthttp://support.huawei.com/supporthttp://support.huawei.com/support


42/42

6 FAQsThis section describes the frequently asked questions about the router.

How Do I Restore Factory Settings?Hold the RESET button for more than 5s.

CAUTION

The user-defined configurations will be lost when you restore factory settings.

What Are the Default Configurations?

The default configurations are as follows:

l The management IP address is 192.168.1.1/24, which is allocated to VLANIF 1. All LAN ports belong to VLAN 1.

l A super administrator is provided, which is a level-3 user with the user name and passwordas admin . You can log in as the admin user using Telnet.

Huawei AR150&200 Series Enterprise RoutersQuick Start Guide 6 FAQs

Documents

AR150&200 Quick Start Guide(03) (1)