APPROVAL OF - TEEAM · APPROVAL OF ELECTRICAL EUIPMENT Information Booklet 4 PREFACE This Information Booklet serves as a guide on the procedure of applying for the Certificateof

APPROVAL OF ELECTRICAL EQUIPMENT

(ELECTRICITY REGULATION 1994)

Information Booklet2016 Edition

FIRST PUBLISHED [2005]SECOND EDITION [2010]THIRD EDITION [2012]FOURTH EDITION [2014]FIFTH EDITION [2016]

© All rights reserved. Reproduction of all or any part of this publication via electronic, mechanical, recording or other medium is strictly prohibited without written consent from the Energy Commission.

PUBLISHED BY:SURUHANJAYA TENAGA (ENERGY COMMISSION)

No. 12, Jalan Tun Hussein, Precinct 2, 62100 Putrajaya, MalaysiaTel : (03) 8870 8500 Fax : (03) 8888 8637Toll Free Number: 1-800-2222-78 (ST)www.st.gov.my

ISBN : 978-967-12023-8-8ST Publication No. : ST(P) 13/09/2016

PRINTED IN MALAYSIA

Information Booklet APPROVAL OF ELECTRICAL EQUIPMENT

3

Chapter

Preface1 Introduction2 Who Should be Concerned with this Booklet3 Key Regulations to Note4 PartiesthatNeedtoApplyforCertificateofApproval(CoA)5 List of Regulated Electrical Equipment 5a. Requirements for Manufacturers & Importers to Comply with Minimum Energy Performance Standards (MEPS)6 ApplicationforCertificateofApprovalforElectricalEquipment 6.1 New Application for CoA (Import / Manufacturer) 6.2 Renewal of Application for CoA (Import / Manufacturer) 6.3 Application of CoA for Exhibition7 Application for Release Letter (RL)8 Regulatory Requirement Related to National Differences9 LabellingorCertificationMark

Appendixes

A ApplicationforCertificateofRegistration(COR)toManufacture/ImportB Application for New CoAC Application for Renewal of CoAD Application for CoA for ExhibitionE Application for Release Letter (RL) on Electrical EquipmentF SampleofCertificateofRegistrationtoManufacturer/ImporterasFormV1G Sample of CoA for importer (new, renewal or exhibitor) as Form VH Sample of CoA for manufacturer (new or renewal) as Form WI Sample of COR as Conformity Assessment Body as Form U1 J Acceptable and Non-acceptable 2-pin Mains Plug

Page

4567

161730

32333638404146

53545658596162636465

CONTENTS

APPROVAL OF ELECTRICAL EQUIPMENT Information Booklet

4

PREFACE

ThisInformationBookletservesasaguideontheprocedureofapplyingfortheCertificateofApproval (CoA) to manufacture, import, display, sell or advertise any electrical equipment prescribed under sub regulation 97(1) of the Electricity Regulations 1994 and other related regulatory requirements therein. It can be downloaded from the website www.st.gov.my.

The Energy Commission (the Commission) expressly disclaim all liability to any person in respect of any statement in or omission from this Information Booklet to the extent permitted by the law and nothing contained in this Information Booklet should be taken as constituting any amendment to the Electricity Supply Act 1990 [Act 447] or the ElectricityRegulations1994.Intheeventofanyconflict,Act447ortheRegulationsshallatall times take precedence. This Information Booklet should not, therefore be regarded as or substitute for familiarising yourself with Act 447 or the Regulations, or where necessary, obtaining specificadviceforyourindividualposition.

The Commission reserves the right to amend and introduce new requirements to the aforementioned procedures of obtaining a CoA.

Our address is:

Energy Commission Malaysia No. 12, Jalan Tun Hussein Precinct 2 62100, Putrajaya.

Toll Free Number : 1-800-2222-78 Telephone : 03-8870 8500 Fax : 03-8888 8637

www.st.gov.my


5

CHAPTER 1

INTRODUCTION

Why CoA is required?

The objective for the issuance of CoA under the Electricity Regulations 1994 is to ensure that all activities to manufacture, import, display, sale or advertisement of:

(a) any domestic equipment;(b) any low voltage equipment which is usually sold directly to the general public; or(c) any low voltage equipment which does not require special skills in its operation,

meetsthespecifiedsafetyandefficientuseofelectricityrequirements.

Consumers’ interests in the use of electrical equipment shall be protected through the determination of the equipment being :-

(a) compatible to Malaysian electricity supply system;(b) complying to standards; (c) tested by accredited laboratory;(d) labelled with SIRIM-ST’s label.

Therefore,bycomplyingwiththespecifiedminimumrequirementsriskofaccidentssuchasfire, electric shock, explosion, radiation and other hazardswhich could result in injuries ordeathstohumansandordamagestopropertiescanbeminimizedoravoided.


6

CHAPTER 2

WHO SHOULD BE CONCERNED WITHTHIS BOOKLET

Consumers

In line with the safety requirements as well as to safeguard consumer’s interests and to ensuretheefficientuseofelectricity,consumersshouldonlypurchase:

(a) any domestic equipment;(b) any low voltage equipment which is usually sold directly to the general public; or(c) any low voltage equipment which does not require special skills in its operation,

whichhavebeenapprovedbytheCommissionandaffixedwithapredeterminedlabel.

Manufacturers, Importers, Exhibitors, Sellers and Advertisers

Manufacturers, importers, exhibitors, sellers and advertisers of any electrical equipment prescribed under sub regulation 97(1), of the Electricity Regulations 1994 must ensure that theirobligationsunderthesaidRegulationsarefulfilled.

This Information Booklet is to assist manufacturers, importers, exhibitors, sellers and advertisersinunderstandingandfulfillingtherequirementsandproceduresforobtainingtheCoA and other related regulatory requirements determined by the Energy Commission.


7

CHAPTER 3

KEY REGULATIONS TO NOTE

Reference to Electricity Regulations 1994;

Requirement to apply for CoAAmendment of Subject to regulations 97C, 97D, 97E and 101A, no person shall Regulation 97 manufacture, import, display, sell or advertise -

(a) any domestic equipment; (b) any low voltage equipment which is usually sold directly to the

general public; or (c) any low voltage equipment which does not require special skills in

its operation, unless the equipment is approved by the Commission.

Recognition of foreign conformity assessment bodyRegulation 97 (A) (1) For the purposes of certifying any equipment under regulation 97,

the Commission shall give a recognition to a foreign conformity assessment body, in a manner that may be determined by the Commission.

Provided that, the foreign conformity assessment body shall be recognised, registered or licensed by the relevant authority in the country in which the foreign conformity assessment body carries on its business.

(2) The Commission shall cease to recognise the foreign conformity assessment body under subregulation (1), if the recognition, registration or licence granted to the foreign conformity assessment body is revoked by the relevant authority.

(3) All test reports, certificates, records or technical files produced by a foreign conformity assessment body in accordance with these Regulations shall be recognised as valid and subsisting for the purposes of this Part, without prejudice to any further testing or assessment to be done to them as the Commission deems necessary.

Registration of local conformity assessment bodyRegulation 97 (B) (1) For the purposes of certifying any equipment under regulation

97, a local conformity assessment body shall apply to be registered with the Commission, in a manner that may be determined by the Commission.

Provided that, the local conformity assessment body has been accredited by the accreditation authority.


8

(2) A local conformity assessment body who is register as conformity assessment body as set out in Form U1 of the First Schedule (as in Appendix I).

(3) A Certificate of Registration issued under subregulation (2) shall be valid for not less than one year and not exceeding three years from the date of issue or renewal of such certificate.

Registration of manufacturer and importer Regulation 97 (C) (1) Any person who manufactures or imports any equipment

under regulation 97 shall apply to be registered with the Commission, in a manner that may be determined by the Commission.

(2) A manufacturer or importer who is registered under subregulation (1) shall be issued with a Certificate of Registration to manufacture or import as set out in Form V1 of the First Schedule (as in Appendix F).

(3) A Certificate of Registration issued under subregulation (2) shall be valid for not less than one year and not exceeding fiveyearsfromthedateofissueorrenewalofsuchcertificate.

Submission of test report or Certificate of Conformity by manufacturerRegulation97(D) (1) Any manufacturer issued with a Certificate of Registration

under regulation 97C shall submit to the Commission- a. a test report as to the equipment’s conformity with the safety

standards as recognised by the Commission; or b. a Certificate of Conformity issued by a local conformity

assessment body.

(2) A test report under subregulation (1) shall be issued by a testing laboratory accredited by the accreditation authority and the test report shall be valid for not less than one year and not exceedingfiveyearsfromthedateofthereport.

(3) ACertificateofConformityundersubregulation(1)shallbevalid for not less than one year and not exceeding three years from the dateofthecertificate.

(4) Uponexpiryofa test reportorCertificateofConformity,as the case may be, the manufacturer shall submit a new test report or Certificate of Conformity to the Commission in accordance with this regulation.

(5) A manufacturer who submits a test report or Certificate of Conformity under this regulation shall ensure that such test report orCertificateofConformityhasavalidityperiodofnotlessthanone year before the expiry date.


9

Submission of test report or Certificate of Conformity by importer.Regulation97(E) (1) Any importer issued with a Certificate of Registration under

regulation 97 shall submit to the Commission:- a. a test report as to the equipment’s conformity with the safety

standards as recognised by the Commission; or b. a Certificate of Conformity issued by a foreign conformity

assessment body recognised by the Commission under regulation 97A.

(2) A test report under subregulation (1) shall be issued by a testing laboratory recognised by the Commission and the report shall be valid for not less than one year and not exceedingfiveyearsfromthedateofthereport.

(3) A Certificate of Conformity under subregulation (1) shall be valid for not less than one year and not exceeding three years fromthedateofthecertificate.

(4) Uponexpiryofa test reportor theCertificateofConformity,as the case may be, the importer shall submit a new test report or Certificate of Conformity to the Commission in accordance with this regulation.

(5) An importer who submits a test report or Certificate of Conformity under this regulation shall ensure that such test report or Certificate of Conformity has a validity period of not less than one year before the expiry date.

Duties to keep technical files of equipment, etc.Regulation97(F) (1) AmanufacturerorimporterissuedwithaCertificateofRegistra-

tionunderregulation97Cshallkeepallfilesofanyequipmentis-suedtogetherwithatestreportorCertificateofConformity,asthecase may be, for not less than ten years after the last equipment has left the production line.

(2) A testing laboratory accredited by the accreditation authority, shall keepall technicalfilesofanyequipment issued togetherwithatest report for not less than six years after the expiry of that test report.

(3) AlocalconformityassessmentbodyshallkeepalltechincalfilesofanyequipmentissuedwithaCertificateofConformintyfornotlessthansixyearsaftertheexpiryofthevalidityoftheCertificateof Conformity.

Marking or labelling of approved equipmentRegulation 98 Where an equipment has been approved for manufacture, import,

display, sale or advertisement by the Commission, the person to whom a Certificate of Approval has been is sued under regulation 97 may be required by the Commission to mark or


10

label the equipment and he shall do so in the manner to be determined by the Commission.

Samples of equipment to be delivered to CommissionRegulation99 (1) Any application for a Certificate ofApproval of any equipment

referred to in regulation 97 shall be made to the Commission in the manner to be determined by the Commission.

(2) The applicant shall deliver to the Commission samples of the equipment in subregulation (1) and such other information in connection therewith, including drawings, photographs, pamphlets and technical literature, as the Commission may require.

(3) Asampledeliveredshallhaveattachedoraffixedtheretoalabelbearing the following particulars:

a. the full name of the applicant; b. the nature of the equipment; c. theenergyefficiencyoftheequipment;and d. the catalogue or type number of the manufacturer, or any

other means of identifying the equipment

(4) The Commission shall not be liable for any loss or damage caused to any equipment delivered under subregulation (2).

Test and modification before approvalRegulation 100 (1) The Commission may cause one or more samples of the

equipment in regulations 99 to be examined and tested.

(2) Where the Commission considers that the equipment examined and tested in subregulation (1) is likely to cause danger, the person applying for approval thereof shall modify or alter the equipment to suit the Commission’s requirements before submitting any further samples thereof.

Submission for test and seizure of dangerous equipmentRegulation 101 (1) The Commission may at any time by notice in writing require

a person who manufactures, imports sells and advertises any equipmenttodeliver,withinsuchtimeasmaybespecifiedinthenotice, samples of the equipment for an examination and a test thereof.

(2) If any equipment is, in the opinion of the Commission, unsafe or dangerous or likely to become unsafe or dangerous to use, the Commission may prohibit the manufacture, import, display, advertisement or sale of the equipment and may direct the person in subregulation (1) to withdraw immediately all the equipment fromuse or sale andwhere necessarymay seize and removesuch equipment.


11

(3) The Commission shall not be liable for any loss or damage causedtoanyequipmentdeliveredorseizedandremovedunder subregulation (1) or (2), as the case may be.

Efficient use of electricity by equipmentRegulation101A (1) For the purpose of efficient use of electricity, prior to an

applicationforaCertificateofApprovalunderregulation97,anyperson who manufactures, imports, sells or offers for sale or lease any equipment under that regulation, shall ensure that such equipment meets the energy performance testing standards, the minimum energy performance standards and the efficiency ratings as set out in the Fourth Schedule.

(2) For the purposes of subregulation (1), a manufacturer or an importer of such equipment shall submit an energy performance testing report in accordance with regulation 101B.

(3) Any equipment thatmeets all the requirements of efficient use of electricity under subregulation (1) shall be affixed with an efficiency rating label in such form and manner as may be determined by the Commission.

Energy performance testing reportRegulation 101B (1) An energy performance testing report under subregulation

101A(2) shall be submitted to the Commission, in a manner that may be determined by the Commission.

(2) An energy performance testing report referred in subregulation (1) shall be valid for not less than one year and notexceedingfiveyearsfromthedateofthereport.

(3) Upon expiry of an energy performance testing report, a manufacturer or an importer shall submit a new energy performance testing report to the Commission in accordance with this regulation.

(4) A manufacturer or an importer who submits an energy performance testing report under this regulation shall ensure that such test report has a validity period of not less than one year before the expiry date.

Submission for test and seizure for the purpose of efficient use of electricityRegulation 101C (1) The Commission may, at any time, by notice in writing, require

any person who manufactures, imports, sells or offers for sale or lease such equipment as referred to in regulation 101A, to deliver, within such period as may be specified in the notice, samples of the equipment for an examination and a test.

(2) If, in the opinion of the Commission, any equipment which does not fulfill the requirements of efficient use of electricity under regulation 101A, the Commission may prohibit the


12

manufacturing, importing, selling or offering for sale or lease of the equipment and may direct the person referred to in subregulation (1) to withdraw or recall within the stipulated period, all the equipment from manufacturing, importing, selling or offering for sale or lease and where necessary, may seizeandremovesuchequipment.

(3) The Commission shall not be liable for any loss or damage caused in the delivery or seizure and removal of equipment under subregulation (1) or (2), as the case may be.

Renewal of Certificate of RegistrationRegulation102 The renewal of any Certificate of Registration issued under regulation 97B and 97C shall be made not less than fourteen days beforethedateofexpiryoftheCertificate.

Transfer of Certificate of RegistrationRegulation103 (1) NoCertificate of Registration issued under regulation 97B and

97Cshall be transferredby theholder of theCertificate toany other person except with the written permission of the Commission.

(2) The holder of any Certificate of Registration issued under regulation 97B and 97C shall obtain approval from the Commission in writing for any change of name or address in connection with the business and the Certificate shall beamended or replaced without payment of any fee.

Cancellation of Certificate of RegistrationRegulation104 (1) The Commission may cancel a Certificate of Registration

issued under regulation 97B and 97C if – a. theholderoftheCertificateceasestocarryonthebusiness

in respect of which he is registered; b. theholderoftheCertificatehasbeenadjudicatedabankrupt; c. the company goes into liquidation; d. the holder of the Certificate or his servant or agent

contravenes or fails to comply with any provisions of the Act or these Regulations; or

e. the holder of the Certificate has obtained the Certificate by making or causing to be made any false or fraudulent declaration,certificationorrepresentation,eitherinwritingorotherwise.

(2) WhereaCertificateofRegistrationiscancelledbytheCommission pursuanttosubregulation(1),theCertificateshallbereturnedtotheCommission by the person, towhom theCertificatewasissued,withinfourteendaysofthepersonbeingnotifiedinwritingof the cancellation.


13

Removal from and reinstatement to the Register of Certificate of RegistrationRegulation 105 (1) There shall be removed from the Register the name and other

particulars of anypersonwhoseCertificateofRegistrationwas issued under regulation 97B and 97C –

a. where he has failed to renewhisCertificate ofRegistration by the date of expiry thereof; or

b. wherehisCertificateofRegistrationhasbeencancelledunderregulation 104.

(2) A person whose name has been removed from the Register under subregulation (1) may appeal, within thirty days of the removal from the Register, for reinstatement and the Commission, upon receipt of satisfactory evidence or reasons for his reinstatement, may register him again.

(3) The person referred to in subregulation (2) who feels aggrieved by the decision of the Commission not to reinstate him may apply to the Minister for re-consideration of the matter.

(4) The application under subregulation (3) shall be made in writing within twenty-one days from the date of the decision of the Commission and shall contain the grounds of grievance.

(5) The decision of the Minister on the matter referred to him undersubregulation(3)shallbefinal.

Renewal of CoARegulation106 Renewal of a Certificate of Approval issued under regulation 97 shall be made not less than 14 days before the date of expiry of the Certificate.

Transfer of CoARegulation107 (1) NoCertificate ofApproval issued under regulation 97, shall be

transferred by the holder of theCertificate to any other person except with the written permission of the Commission.

(2) Theholder of aCertificate ofApproval issuedunder regulation 97, shall obtain approval from the Commission in writing for any change of name or address in connection with the business and the Certificate shall be amended or replaced without payment of any fee.

Cancellation of CoARegulation108 (1) TheCommissionmaycancelaCertificateofApproval issuedin

respect of any equipment referred to in regulation 97 if- a. the equipment is found to be unsafe for use upon any

examination or test thereof; b. thepersontowhomtheCertificatewasissued,usesit fora


14

purpose different from that for which it was issued or in a manner calculated to mislead or deceive the public;

c. the person has contravened or failed to comply with any of the provisions of the Act or these Regulations; or

d. the holder of theCertificate has obtained theCertificate by making or causing to be made any false or fraudulent declaration, certification or representation, either in writing or otherwise

(2) Where a Certificate of Approval is cancelled by the Commission pursuanttosubregulation(1),theCertificateshallbereturnedto theCommissionbythepersontowhomtheCertificatewasissued withinfourteendaysofthepersonbeingnotifiedinwritingofthe cancellation.

Removal from and Reinstatement Approval to the Register of CoARegulation 109 (1) There shall be removed from the Register the name and other

particulars or any person whose Certificate of Approval was issued under regulation 97—

a. wherehehas failed to renewhisCertificate ofApproval by the date of expiry thereof; or

b. wherehisCertificateofApproval hasbeencancelledunder regulation 108.

(2) A person whose name has been removed from the Register under subregulation (1) may appeal, within 30 days of the removal from the Register, for reinstatement and the Commission, upon receipt of satisfactory evidence or reasons for his reinstatement, may register him again.

(3) The person referred to in subregulation (2) who feels aggrieved by the decision of the Commission not to reinstate him, may apply to the Minister for re-consideration of the matter.

(4) The application under subregulation (3) shall be made in writing within twenty-one days from the date of the decision of the Commission and shall contain the grounds of grievance.

(5) The decision of the Minister on the matter referred to him undersubregulation(3)shallbefinal.

Market surveillanceRegulation 109A (1) The Commission may, from time to time, carry out market

surveillance to determine if any equipment referred to in regulation 97 is safe and is affixed with a label in accordance with regulation 98 or an efficiency rating label, or both, as the case may be.

(2) Whoever, intentionally or knowingly- a. removes, withdraws or assists in the removal or withdrawal


15

of any equipment, which is not labelled in accordance with regulation 98 or which does not bear an efficiency rating label, or both, as the case may be, from any premises in ordertoobstructorhindertheCommission,itsauthorisedofficers or agents from exercising any of its powers; or

b. harbours, keeps, conceals, or is in the possession of any equipment which is not labelled in accordance with regulation 98orwhichdoesnotbearanefficiencyratinglabel,orboth,as the case may be, with the intention to sell or offer for sale, Commits an offence.

Savings and transitional provision (1) Any existing local conformity assessment body already in

operation before the coming into operation of these Regulations, shall apply to be registered with the Commission within a period of six months from the date of coming into operation of these Regulations.

(2) Upon coming into operation of these Regulations, any manufacturer or importer shall apply to be registered with the Commission in accordance with regulation 97C, within a peri-od of one year from the date of coming into operation of these Regulations.

(3) Any existing equipment which had been manufactured, imported, sold or offered for sale or lease before the coming into operation of these Regulations shall be required to comply with regulation 101A, within one year from the date of coming into operation of these Regulations.

Offences and PenaltySection 37(1), Any person who tampers with or adjusts any installation or part Electricity Supply thereof or manufactures or imports or sells any equipment so as to (Amendment) cause or to be likely to cause danger to human life or limb or injury Act 2015 to any equipment or other property shall be guilty of an offence and for each such offence shall, on conviction, be liable to a fine not exceeding RM1,000,000 or to imprisonment for a term not exceeding 10 years or to both.

Regulation 122, Unless otherwise made an offence under the Act, a person who contravenesElectricity or fails to comply with any of the provisions of these Regulations shall Regulation1994 beguiltyofanoffenceandshall,onconviction,beliabletoafinenot exceeding RM5,000 or to imprisonment for a term not exceeding 1 year or to both.


16

CHAPTER 4

PARTIES THAT NEED TO APPLY FOR CERTIFICATE OF APPROVAL (CoA)

ImportersImporters of electrical equipment under sub regulation 97(1) of the Electricity Regulations 1994 are required to apply for the CoA from the Commission. An importer shall be a Malaysian company registered with the Companies Commission of Malaysia.

ManufacturersManufacturers who manufacture electrical equipment under regulation 97(1) of the Electricity Regulations 1994 are required to apply for the CoA.

ExhibitorsExhibitors who display electrical equipment under sub regulation 97(1) of the Electricity Regulations 1994 are also required to apply for the CoA.

Sellers and AdvertisersSellers and advertisers of electrical equipment are required to apply for the CoA and to ensure that the electrical equipment to be sold or advertised are in accordance with sub regulation 97(1), 97(2) and 98 of the Electricity Regulations 1994.


17

CHAPTER 5

LIST OF REGULATED ELECTRICAL EQUIPMENTNote: Regulated Electrical Equipment are to be tested to the specified standards. Equipment that are tested and certified to the same standards of later revisions are also acceptable.

No

1

Category

PLUG TOP/PLUG

Description of Regulated Equipment

(a) Plug •makesadetachable connectionbetweenthe contactsofasocket-outlet andtheconductorsofa flexiblecord; •hasinsulatingsleeveson thelineandneutralplug pinsforinsertionintoa socket-outlet;and •hasamaximumratingof 15A;

(b) Coupler •isforattachmenttoa flexiblecord;and •makesadetachable connectionbetweenthe conductorsofthecordand thepinsorcontactsof anylowvoltageappliance orequipmentofatype intendedorgenerallyused forhouseholdapplications

(c) Adaptor •extendssupplyfroma socket-outlet; •incorporatesoneormore integralsocket-outlets; and •hasinsulatingsleeveson thelineandneutralplug pins.

(d) Connector •Connectingdevicesforthe connectionoftwoormore electricalcopper conductors.

Detail of Equipment

FlatNon-RewirableTwoPolePlugwithsup-plycord(max.2.5A)

13AFusedPlug

15 A Plug

ApplianceCoupler

InterconnectionCoupler

Adaptor(Multiways)

IntegratedAdaptor

TravelAdaptor

ElectricalConnector (connectingdevice)

Connectingdevicewithscrewtypeclampingunit

Connectingdevicewithscrew-lesstype clampingunit

StandardsNationalStandard

MS1578:2003

MS589-1:2011

MS1577:2003

MSIEC60320-1:2010

MSIEC60320-1:2010MSIEC60320-2-2:2011

MS589-3:2012

MS1144:1998

NocorrespondingMSNocorrespondingMS

MSIEC60998-1:2005

MSIEC60998-1:2005MSIEC60998-2-1:2005

MSIEC60998-1:2005MSIEC60998-2-2:2005

EquivalentInternational

Standard

BSEN50075:1991

BS1363:PT.1:1995+A1,A2,A3

Nocorrespond-inginternationalstandard

IEC60320-1:2007

IEC60320-1:2007IEC60320-2-2:1998

BS1363PT.3:1995+A1,A2,A3

BS5733:2010

IEC60884-1:2006IEC60884-2-5:1995

IEC60998-1:2002

IEC60998-1:2002IEC60998-2-1:2002

IEC60998-1:2002IEC60998-2-2:2005


18

Standards

NationalStandard


Standard

No Category Description of Regulated Equipment

Detail of Equipment

2

3

4

•isanair-breakswitch; •isforconnectiontothe wiringofanelectric installation; •isprimarilyformounting onaverticalsurface •ismanuallyopenedand manuallyclosed;and •hasaratingupto63A.

(2) SocketOutlet •isforfixingatapointat whichfixedwiring terminates; •providesadetachable connectionwiththepins ofaplug; •hastwo,orthreecontacts; •andhasamaximumrating of15A; •withswitchandwithout switchsocketoutlet.

(b) Portable Adevicecomprisinga flexiblecableorcord attachedtoareelso constructedthattheflexible cablemaybecompletely woundontothereel,and providedwithaplugand oneormoresocketoutlets.

(a) LampHolder Holdstubularfluorescent lampbutdoesnotinclude: Alampholderwhichby designisrestrictedto specificappliances.

SWITCH AND DIMMER

SOCKET OUTLET

FLUORES-CENT LAM-PHOLDER / STARTER HOLDER

Connectingdevicewithinsulation-piercing clampingunits

Twist-onconnectingdevice

Connectingboxes

GeneralPurposeSwitch

DoorBell&Chime

ElectronicSwitch

Remote-controlSwitch

TimeDelaySwitch

CookerControlUnit

ElectricShaverSocketOutlet

13ASwitch&unswitchsocketoutlet

15Asocketoutlet&Plug

Portable2pinsocketoutletclassII

Portablecablereel

Lampholderfortubularfluorescentlamp

MSIEC60998-1:2005MSIEC60998-2-3:2005

MSIEC60998-1:2005MSIEC60998-2-4:2005

MS1873:2005MS1873-22:2006

MSIEC60669-1:2012

MSIEC61558-1:2005MSIEC61558-2-8:2007

MSIEC60669-1:2012MSIEC60669-2-1:2012

MSIEC60669-1:2012MSIEC60669-2-2:2012

MSIEC60669-1:2012MSIEC60669-2-3:2012

NocorrespondingMS

MSIEC61558-1:2005MSIEC61558-2-5:2006

MS589-2:2011

MS1577:2003

MS1579:2003

MS1141:2006

MSIEC60400:2006

IEC60998-1:2002IEC60998-2-3:2002

IEC60998-1:2002IEC60998-2-4:2002

IEC60670-1:2002IEC60670-22:2002

IEC60669-1:2007

IEC61558-1:2009IEC61558-2-8:2010

IEC60669-1:2007IEC60669-2-1:2009

IEC60669-1:2007IEC60669-2-2:2006

IEC60669-1:2007IEC60669-2-3:2006

BS4177:1992

IEC61558-1:2009IEC61558-2-5:2010

BS1363:PT2:1995+A1,A2,A3



IEC61242:2008withmodification

IEC60400:2004


19

Standards

NationalStandard


Standard


Detail of Equipment

5

6

7

CEILING ROSE

BAYONET CAP and MULTIWAYS ADAPTOR

LAMP FITTING

(b) StarterHolder toholdaglowstarter butdoesnotinclude: astarterholderwhichby designisrestrictedto specificappliances.

•aterminalforconnection toalampholderviaa cable.

•EdisonScrewLampholder lampholderswithEdison screwthreadE14,E27and E40,designedforholding andconnectingtothe supplyoflamps.

•holdsabayonetcaplamp, bayonetcapadaptor

butdoesnotinclude: •alampholder,whichby design,isrestrictedto specificappliances •alampholderwhichisfor incorporationinan industrialequipment

(a) Luminaires •providesillumination;

•incorporateelectriclight sourcesforoperationfrom supplyvoltageupto 1000V.

(b) GlowStarter •isforstartingpreheattype fluorescentlamps;

•isaglow-starttype;and •hasanenclosureof insulatingmaterial •holdsalightsourceor bulb.

Starterholderfortubularfluorescentlamp

CeilingRose

EdisonScrewLampholder

BayonetcapLampholder

BayonetLampAdaptor

FixedgeneralpurposeLuminaires(excludingTube/Bulb),

BattenLuminaires (excludingTube/Bulb),

Luminarieswithself- ballastedfluorescentlamp.

RecessedLuminaires(excludingTube/Bulb)

Glow-starterfortubularfluorescent

MSIEC60400:2006

MS770:1982

MSIEC60238:2008

NocorrespondingMS

MS769:1982withIEC61184:2008

MSIEC60598-1:2012MSIEC60598-2-1:1997

MSIEC60598-1:2012MSIEC60598-2-2:1998

MSIEC60155:1996

IEC60400:2004

BS67:1987

IEC60238:2004

IEC61184:2008+A1

IEC61184:2008withMS769:1982

IEC60598-1:2008IEC60598-2-1:1987

IEC60598-1:2008IEC60598-2-2:2011

IEC60155:2006


20

Standards

NationalStandard


Standard


Detail of Equipment

8

9

CAPACITOR for FLUORES-CENT LAMP

BALLAST / CONTROL GEAR / DRIVER FOR LAMP

(c)Self-ballastedCompact FluorescentLamp(CFL) • Lampwhichcannotbe dismantledwithout beingpermanently damaged,providedwith • alampcapincorperating alightsourceandany elementsneccessaryfor startingandstable operationofthelight source.

(d)LEDLighting

• isusedtogetherwitha ballastinalampcircuit.

(a)Ballast • isforcontrollingthe magnitudeofcurrent flowingthroughthe dischargepathofa fluorescentlamp,

• isoftheindependentor built-intypeintended forusewithluminaires (portableorfixed);or

• isoftheintegraltype suchthatitformsanon- replaceablepartofa fluorescentlamp/ballast combination;or

• isoftheadaptortype suchthatitallowsthe

withEdisonscreworbayonetcaps

Lampcontrolgear:Particularrequirementsford.c.ora.c.supplyelectroniccontrolgearforLEDmodules

Lampholder(ConnectorsforLED-modules)

LEDModulesforgeneral Lighting(eg.doublecappedself-ballastedLEDLamp)

Self-ballastedsinglecappedLED-lampsforgenerallightingservicesbyvoltage>50V

Capacitorsforusein tubularfluorescentlampsandothercircuits.

MagneticBallastfor tabularfluorescentlamp

ElectronicBallastforfluorescentlamp

MSIEC60968:2006MSIEC60969:2006

MSIEC61347-1:2012MSIEC61347-2-13:2012

MSIEC60838-1:2008MSIEC60838-2-2:2008

MSIEC62031:2011withMSIEC60061-1:2005

MSIEC62560:2012

MSIEC61048:2006MSIEC61049:1999

MSIEC61347-1:2012MSIEC61347-2-8:2003MS141PT.2:1993+A1

MSIEC61347-1:2012MSIEC61347-2-3:2003MSIEC60929:2008withMSIEC61000-3-2:2003

IEC60968:1999IEC60969:2001

IEC61347-1:2010IEC61347-2-13:2006

IEC60838-1:2004IEC60838-2-2:2006

IEC62031:2008+A1,A2withIEC60061-1:2005

orIEC62776:2014

IEC62560:2011

IEC61048:2006IEC61049:1991

IEC61347-1:2010IEC61347-2-8:2000IEC60921:2004withmodification

IEC61347-1:2010IEC61347-2-3:2000IEC60929:2011withIEC61000-3-2:2009


21

10

CIRCUIT BREAKER including AC CURRENT OPERATED EARTH LEAK-AGE CIRCUIT BREAKER and MINIATURE CIRCUIT BREAKER

insertionofafluorescent lampintotheballastby theuser;

butdoesnotinclude: •aballastwhichis incorporatedinluminaires certifiedforcompliance withtherequirementsfor electricalequipmentwith increasedsafetytype protection(Exe)forusein hazardouslocations.

b)ControlGear Generalsafetyforlamp controlgearforuseondc supplyupto250Vandor acsupplyupto1000V

(a) ResidualCurrentDevice (RCD) •isolatesorinitiatesa trippingsignaltoisolate alow-voltagesupplyto protectedcircuits, socket-outletsor equipmentintheevent ofacurrentflowtoearth whichexceedsa pre-determinedlevel;

•hasaratedresidualcurrent lessthan300mAfor devicesintendedfor connectiontofixedwiring or10mAforotherdevices; and •hasaratedloadcurrent notexceeding125Afor devicesintendedfor connectiontofixedwiring or20Aforotherdevices.

butdoesnotinclude:- •adeviceintendedto beusedwithaparticular circuit-breakerotherthan •aminiatureovercurrent circuit-breaker;or •adeviceintendedto protectanelectricity supplyauthority distributionsystem.(b) Fuse •isanenclosedair-break

ControlGear

ResidualCurrentCircuitBreaker(RCCB)

ResidualCurrentBreakerwithOvercurrentProtec-tion(RCBO)

MiniatureCircuitBreaker(MCB)foracsupply

MSIEC61347-1:2012

MSIEC61008-1:2012MSIEC61008-2-1:2003orMSIEC61008-1:2012MSIEC61008-2-2:2003

MSIEC61009-1:2012MSIEC61009-2-1:2003orMSIEC61009-1:2012MSIEC61009-2-2:2003

MSIEC60898-1:2007

IEC61347-1:2010

IEC61008-1:2010IEC61008-2-1:1990orIEC61008-1:2010IEC61008-2-2:1990

IEC61009-1:2010IEC61009-2-1:1991orIEC61009-1:2010IEC61009-2-2:1991

IEC60898-1:2003

Standards

NationalStandard


Standard


Detail of Equipment


22

11 PORTABLE LUMINAIRE LAMP

switch; •opensalowvoltage circuitautomaticallyunder pre-determinedconditions ofover-current; •hasanominalratingnot exceeding125Aandhas acurrentbreakingcapacity ofupto10kA. •isbythefusionofoneor moreofitsspecially designedand proportionedcomponents, opensthecircuitinwhich itisinsertedandbreaks thecurrentwhenthis exceedsagivenvaluefor asufficienttime.Thefuse comprisesallthepartsthat formthecompletedevice.

•isahouseholdtype; providesilluminationorfor decorativepurposes, produceslight; •isfittedwithasupply flexiblecord,anappliance inletsocketorapower supplyunitwithintegral pinsforinsertionintoa socketoutlet; •isforstandingonatableor floor,orisfittedwitha clamporsimilarfor attachmenttoverticalor horizontalsurfaces; •isforusewithtungsten filament,tubular fluorescentorother dischargelamps;and •isconstructedtorepresent amodel,personoranimal andislikelytobetreated byachildasatoy;or •hasmetalpartswhichare requiredtobeearthed ordoubleinsulatedfrom liveparts(excludinglive partsofanallinsulated lampholder) •isforinspectionpurposes usingillumination; •holdsalightsourceor bulb;and •ishandheld; butdoesnotinclude •handlampwitha

MiniatureCircuitBreaker(MCB)forac&dcsupply

FuseBase&Carrierupto32A

Fuse/FuseLinkupto63A

Switchfuseupto63A.

StandingLampwithdetachableornon- detachablemainssupplyflexiblecord,

StandingLamp&adaptor,

Tablelampwithdetach-ableornon-detachablemainssupplyflexiblecord,

TableLamp&adaptor,

PortableLEDLamp

NightLampintegralwithdirectinplug.

HandLamp&adaptor,

MSIEC60898-2:2007

MSIEC60269-1:2011MSIEC60296-2:2011

MSIEC60269-2:2011MSIEC60269-3:2011

MSIEC60947-1:2010MSIEC60947-3:2010

MSIEC60598-1:2012MSIEC60598-2-4:2003

MSIEC60598-1:2012MSIEC60598-2-12:2010

MSIEC60598-1:2012MSIEC60598-2-8:2006

IEC60898-2:2003

IEC60269-1:2006IEC60269-2:2006

IEC60269-2:2006IEC60269-3:2010

IEC60947-1:2007IEC60947-3:2008

IEC60598-1:2008IEC60598-2-4:1997

IEC60598-1:2008IEC60598-2-12:2006

IEC60598-1:2008IEC60598-2-8:2007

Standards

NationalStandard


Standard


Detail of Equipment


23

Standards

NationalStandard


Standard


Detail of Equipment

12

13

KETTLE including HEATING ELEMENTS IF SUPPLIED SEPARATELY

KITCHEN MACHINE

magnificationfacility. •isahouseholdtype; isportable; •hasacapacitynot exceeding10L;and •heatsliquidfor: >humidifyingroomair;or >hotbeverage;or >cookingpurpose

•isahouseholdtype; •isforthepreparationof foodbymechanical means;or •isforopeningcans;or •isforsharpeningofknives

WarmingPlate

DeepFryer

HeatingLiquidssuchas:Coffee/TeaMaker,FoodSteamer,EggBoiler,Jug,SlowCooker,SteamBoat,Kettle,Airpot,BottleWarmer,Sterillizer.

Multi-purposecooker

WaterDispenser/Filter

WaterDispenser-Hot

WaterDispenser-Cold

WaterDispenser–HotandCold

BuiltinHob

Blender,Chopper,FoodProcessor,JuiceExtractor,Grinder,Mixer.

MSIEC60335-1:2013MSIEC60335-2-12:2014

MSIEC60335-1:2013MSIEC60335-2-13:2006

MSIEC60335-1:2013MSIEC60335-2-15:2004

MSIEC60335-1:2013MSIEC60335-2-9:2014MSIEC60335-2-13:2006MSIEC60335-2-15:2004

MSIEC60335-1:2005

MSIEC60335-1:2005MSIEC60335-2-15:2004

MSIEC60335-1:2005MS1597-2-24:2005

MSIEC60335-1:2005MSIEC60335-2-15:2004MS1597-2-24:2005

MSIEC60335-1:2013MSIEC60335-2-36:2014

MSIEC60335-1:2013MSIEC60335-2-14:2014

IEC60335-1:2006IEC60335-2-12:2002

IEC60335-1:2006IEC60335-2-13:2004

IEC60335-1:2006IEC60335-2-15:2002

IEC60335-1:2006IEC60335-2-9:2008IEC60335-2-13:2004IEC60335-2-15:2002

IEC60335-1:2004

IEC60335-1:2004IEC60335-2-15:2002

IEC60335-1:2004IEC60335-2-24:2010

IEC60335-1:2004IEC60335-2-15:2002IEC60335-2-24:2010

IEC60335-1:2006IEC60335-2-36:2008

IEC60335-1:2006IEC60335-2-14:2002


24

Standards

NationalStandard


Standard


Detail of Equipment

14

15

16

17

18

TOASTER / OVEN (Cooking Appliance)

RICE COOKER

REFRIGERA-TOR

IMMERSION WATER HEATER

WATER HEATER including HEATING ELEMENTS IF SUPPLIED SEPARATELY

•isahouseholdtype;and •isfortoastingbreador similarfood; •isforcookingorwarming foodbyelectricalenergy; •appliesheattofood,liquid orothersubstancesina chamberbymeansof high-frequencyelectro- magneticradiation.

•isahouseholdtype;and •isusedforcookingrice

•isahouseholdtype;and •coolsandstoresfood.

Butdoesnotinclude– •atype,promoted exclusivelytoindustry/ commercialsector.

•isahouseholdtype; •isforheatingliquidin whichitmaybeimmersed; and •isselfcontained; andincludes– •aquariumtypeimmersion heaters

(a) Storage •isforheatingandstorage ofwaterforbathing, washingorsimilar purposes; •incorporatesaheating element;and •hasastoragecapacitynot lessthan4.5Lornotmore than680L.

(b) Instantaneous •isforheatingwater; •isoftheinstantaneous type;and •incorporateslivepartsin contactwithwater.

StationaryElectricOven,InductionHob.

BreadMaker,BreadToaster,PortableOven,InductionCooker,Grill,SandwichMaker/WaffleMaker,Roaster.

MicrowaveOven

RiceCooker

Refrigerator,Freezer,Minibar.

FixedImmersionHeater

PortableImmersionHeater

StorageWaterHeater

InstantaneousWaterHeater

MSIEC60335-1:2013MSIEC60335-2-6:2014

MSIEC60335-1:2013MSIEC60335-2-9:2014

MSIEC60335-1:2013MSIEC60335-2-25:2014

MSIEC60335-1:2013MSIEC60335-2-15:2004

MSIEC60335-1:2013MS1597:Part2-24:2005

MSIEC60335-1:2013MSIEC60335-2-73:2014

MSIEC60335-1:2013MSIEC60335-2-74:2010

MSIEC60335-1:2013MS1597-2-21:2011

MSIEC60335-1:2013MS1597-2-35:2010

IEC60335-1:2006IEC60335-2-6:2005

IEC60335-1:2006IEC60335-2-9:2008

IEC60335-1:2006IEC60335-2-25:2010

IEC60335-1:2006IEC60335-2-15:2002

IEC60335-1:2006IEC60335-2-24:2005withmodification

IEC60335-1:2006IEC60335-2-73:2009

IEC60335-1:2006IEC60335-2-74:2006




25

Standards

NationalStandard


Standard


Detail of Equipment

19

20

21

WASHING MACHINE

FAN

HAND OPERATED HAIR DRYER/ HAIRCARE/ SKIN CARE

•isahouseholdtype;and •isusedforwashing/drying clothes.

butdoesnotinclude- •atype,promoted exclusivelytoindustry/ commercialsector.

•householdtype; •forwashingandrising dishes.

•isahouseholdtype; •hasaprimaryfunctionof movingairinitsvicinity; and •isselfcontained;

•isahouseholdtypeora commercialhand-held type;and •isfordrying,stylingorthe caringofhumanhair.

WashingMachinewithdryer

WashingMachinewithseparatespincontainer

TumblerDryers

ClothDryers(onracklocated)

DishWasherandotherutensils.

Moving-louverfan,Ceilingfan,Autofan,Pedestalfan,Tablefan,Wallfan&appliestotheirseparateregulatorsandwithblade. Ventilatingfan,Decorativefan&appliestotheirseparateregulatorsandfanwithoutblade.

RangeHood

CleaningAppliances(eg.AirPurifier)

Humidifiers(eg.AirCooler)

HairDryer,HairStylingSet,HandDryer,IonicFacialSteamerorsimilartoit.

MSIEC60335-1:2013MS1597:Part2-7:2005

MSIEC60335-1:2013MSIEC60335-2-4:2007MS1597:Part2-7:2005

MSIEC60335-1:2013MSIEC60335-2-11:2014

MSIEC60335-1:2013MSIEC60335-2-43:2014

MSIEC60335-1:2013MS1597-2-5:2005

MSIEC60335-1:2013MS1597-2-80:2010MS1220:2010

MSIEC60335-1:2013MS1597-2-80:2010

MSIEC60335-1:2013MSIEC60335-2-31:2014

MSIEC60335-1:2013MSIEC60335-2-65:2014

MSIEC60335-1:2013MSIEC60335-2-98:2014

MSIEC60335-1:2013MSIEC60335-2-23:2007


IEC60335-1:2008IEC60335-2-4:2004IEC60335-2-7:2003withmodification

IEC60335-1:2006IEC60335-2-11:2012

IEC60335-1:2006IEC60335-2-43:2008


IEC60335-1:2006IEC60335-2-80:2004withmodificationforceilingfanonlyIEC60879:1986withmodification

IEC60335-1:2006IEC60335-2-80:2004withmodificationforceilingfanonly

IEC60335-1:2006IEC60335-2-31:2009

IEC60335-1:2006IEC60335-2-65:2008

IEC60335-1:2006IEC60335-2-98:2008

IEC60335-1:2006IEC60335-2-23:2005


26

Standards

NationalStandard


Standard


Detail of Equipment

22

23

24

25

26

27

IRON

SHAVER

VAPORISER

VACUUM CLEANER

HI-FIDELITY SET

VIDEO and VISUAL DIS-PLAY UNIT

•isahouseholdtype; •isforsmootheningor pressingfabricbythe applicationofheator steam;

•ishandheldexceptforany separatesteamgenerator; andincludes: •anyassociatedequipment •isahouseholdtype;and •shaves,cutsortrims humanhair.

•isahouseholdtype;and •Purposeasairfresheners andinsectrepellers.

•isahouseholdtype; •portable;and •removesdust,dirtor moistureandthelikefrom floorcoveringsbysuction; or •removesgardenrefuse fromlawnsorpathsand thelikebysuction. butdoesnotinclude- •atype,promoted exclusivelytoindustry/ commercialsectors.

•isahouseholdtype; •isforreproductionof sound,withlittle distortion,connectedto thesupplymainsasthe onlyenergysource, intendedfordomesticand similargeneralindooruse witharatedsupplyvoltage notexceeding250volts rms. •Anelectronicdevice forreproductionofaudio/ video,connectedtothe supplymains,either directlyorindirectlyand intendedfordomesticand similargeneralindooruse

•isforhouseholduse; •isforreceivingand displayinginformation

Iron

FabricSteamer

Shaver,

HairClippers.

MosquitoMattVapor,AromaVapor(eg.AirFreshener).

VacuumCleaner,

WaterSuctionCleaning.

Sub-woofer,Amplifier,CassettePlayer,Equalizer/Mixer,Hi-FiSystem,Karaoke,PASystem,PortableHi-FiSystem,PortableRadioCassette,Player/Recorder,Radio,RadioAlarm,Tuner/Receiver,Turntables/RecordPlayers,CompactDiscPlayer,Audio/VideoRecorderupto4channels.

Electronicappliancessuchas:LCD,

MSIEC60335-1:2013MSIEC60335-2-3:2006

MSIEC60335-1:2013MSIEC60335-2-85:2014

MSIEC60335-1:2013MSIEC60335-2-8:2002

MSIEC60335-1:2013MSIEC60335-2-101:2014

MSIEC60335-1:2013MSIEC60335-2-2:2006

MSIEC60065:2007

MSIEC60065:2007

IEC60335-1:2006IEC60335-2-3:2005

IEC60335-1:2006IEC60335-2-85:2008

IEC60335-1:2006IEC60335-2-8:1992+A1

IEC60335-1:2006IEC60335-2-101:2008

IEC60335-1:2006IEC60335-2-2:2004

IEC60065:2005orIEC62368-1:2014

IEC60065:2005orIEC62368-1:2014


27

Standards

NationalStandard


Standard


Detail of Equipment

28

29

30

31

32

AUDIO and VIDEO PLAYER UNIT

MASSAGER

AIR CONDI-TIONER(Cooling Capacity of 32,000 Btu/hr & below)

CHRISTMAS LIGHT

DOMESTIC POWER TOOLS (Por-table Type)

fromatransmittingstation orlocalsource •isforthedisplayofpublic orsubscriptiontelevision broadcasts.

•isahouseholdtype; •isforvideorecordingand playbackorfor playbackonly,connected tothesupplymainseither directlyorindirectlyand intendedfordomesticand similargeneralindooruse.

•Isahouseholdtype.

•Aelectricalassemblyto providedeliveryof conditionedairtoan enclosedspace,roomor zone,includingan electricallyoperated refrigerationsystemfor coolingandpossibly dehumidifyingtheair.

•isfordecorative, displayorillumination purposes;andconsistsof– -lampsorlampholders interconnectedbyflexible cordoflessthan2.5mm² cross-sectionalarea;or -lampswithinaflexible enclosure; andincludes–anyintegral powersupplyorcontrol device.

•isformachining,drilling, sawing,orsurface preparation;and •maybeentirelysupported byhandduringoperation.

butdoesnotinclude- •atool,portabletype, promotedexclusively totheindustry/ commercialsector.

LED, Plasma,CRT,andsimilartoit.

VCD,LaserDisc,VideoCassetteRecorder,DVD,VideoRewinder,ChildrenVideoGame.

FootMassagers,MassageBed,MassageChair,MassagePads,HandheldMassagers,MassageBelts.

SplitAir-conditioner,PortableAir-conditioner,CeilingAir-conditioner

LightingChain,RopeLight,Decorative/FestiveLight.

Drill(Drillbitsizeupto15mm)

Grinder(upto100mm)

Sander(upto300W)

CircularSawandcircularknife(CuttingBladeup

MSIEC60065:2007

MSIEC60335-1:2013MSIEC60335-2-32:2014

MSIEC60335-1:2013MS1597-2-40:2005

MSIEC60598-1:2012MSIEC60598-2-20:2013

MSIEC60745-1:2010MSIEC60745-2-1:2011

MSIEC60745-1:2010MSIEC60745-2-3:2010

MSIEC60745-1:2010MSIEC60745-2-4:2011

MSIEC60745-1:2010MSIEC60745-2-5:2010

IEC60065:2005or

IEC62368-1:2014

IEC60335-1:2006IEC60335-2-32:2008


IEC60598-1:2008IEC60598-2-20:2010

IEC60745-1:2006IEC60745-2-1:2006+A1

IEC60745-1:2006IEC60745-2-3:2006

IEC60745-1:2006IEC60745-2-4:2006

IEC60745-1:2006IEC60745-2-5:2006


28

Standards

NationalStandard


Standard


Detail of Equipment

33 ADAPTER / CHARGER

•isahouseholdtype;and •isforstitchingfabricor othermaterial

•isfortheapplicationor removalofsolder;and •ishandheld;

butdoesnotinclude- •asolderingiron promotedexclusivelyto industry

•isahouseholdtype; •isforchargingbatteries otherthanthoseofthe automotivetype; •isselfcontained; •isforchargingoneor morebatteriesforusein otherequipment; •isforchargingbatteryfor useinmobilephone/PDA. •isimportedormanufactured separately(detachable).

A.C.-D.C.Adapters •Adevicetosupplya.c.or d.c.powersupplyfroman a.c.ord.c.source,eitherby

to160mm)

Spraygunfornon-flammableliquid(upto100bars)

JigandSabreSaw(upto60mm)

Planer(upto500W)

Trimmer(upto300W)HedgetrimmerandGrassshears(upto750W)

Routerandtrimmer(upto500W)

HighPressureCleaner

SewingMachine

PortableHeatingToolsuchas:SolderingGun,SolderingIron,HeatGun,HotAirFirelighters,Gluegun.

PortableBatteryCharger(upto12V)

AdapterforITEquip-ment(upto20V)

Generalelectrical appliancesElectronicIsolating

MSIEC60745-1:2010MSIEC60745-2-7:2005

MSIEC60745-1:2010MSIEC60745-2-11:2011

MSIEC60745-1:2011MSIEC60745-2-14:2011

MSIEC60745-1:2010MSIEC60745-2-15:2011

MSIEC60745-1:2010MSIEC60745-2-17:2012

MSIEC60335-1:2013MSIEC60335-2-79:2007

MSIEC60335-1:2013MSIEC60335-2-28:2003

MSIEC60335-1:2013MSIEC60335-2-45:2003

MSIEC60335-1:2013MSIEC60335-2-29:2005

MSIEC60950-1:2007

MSIEC61558-1:2005MSIEC61558-2-6:2005

IEC60745-1:2006IEC60745-2-7:1989

IEC60745-1:2006IEC60745-2-11:2006

IEC60745-1:2006IEC60745-2-14:2006

IEC60745-1:2006IEC60745-2-15:2006

IEC60745-1:2006IEC60745-2-17:2010

IEC60335-1:2006IEC60335-2-79:2005

IEC60335-1:2006IEC60335-2-28:2002

IEC60335-1:2006IEC60335-2-45:2002

IEC60335-1:2006IEC60335-2-29:2002+A1

IEC60950-1:2005orIEC62368-1:2014

IEC61558-1:1998IEC61558-2-6:2009


29

Standards

NationalStandard


Standard


Detail of Equipment

34 WIRE / CABLE/ CORD (non-armoured) 0.5mm² to 35mm²

itselforaspartofan accessory,fordomesticand similargeneralindooruse

•isunscreenedand flexible; •isdesignedforuseatlow voltage; •consistsoftwoorthree elastomerorPVCinsulated coresofmultistrand construction; •hasacross-sectional areaofeachconductor from0.5mm²not exceeding35mm²

Transformer

Switchingmodepowersupply

Electrictoys

Audiovideoequipment

IT&Officeproducts

Shavers

Polyvinylchloride(PVC)Insulatedflexiblecordandcable

Rubberinsulatedcordandflexiblecables

PVC-insulatedcable(non-armoured)forelec-tricpowerandsupply:-non-sheathed

PVC-insulatedcable(non-armoured)forelec-tricpowerandsupply:-sheathed

MSIEC61558-1:2005MSIEC61558-2-17:2007

MSIEC61558-1:2005MSIEC61558-2-7:2007;

MSIEC60065:2007

MSIEC60950-1:2007

MSIEC60335-1:2013MSIEC60335-2-8:2002

MS2112-5:2009

MS140:1987orMS2127-4

MS2112-3:2009

MS2112-4:2009

IEC61558-1:1998IEC61558-2-17:2009

IEC61558-1:2009IEC61558-2-7:2007

IEC60065:2005orIEC62368-1:2014

IEC60950-1:2005orIEC62368-1:2014

IEC60335-1:2006IEC60335-2-8:2000

BSEN50525-2-11:2011orIEC60227-5:2011

BSEN50525-2-11-2011IEC60245-1:2008IEC60245-4:2011

IEC60227-3:1997

IEC60227-4:1997


30

1.

2.

3.

4.

5.

CHAPTER 5A

LIST OF REGULATED ELECTRICAL EQUIPMENT THAT ARE TO BE TESTED TO THE SPECIFIED MINIMUM ENERGY PERFORMANCE STANDARDS (MEPS)

MEPS Value Efficiency RatingsNo Equipment Type of Equipment

MEPS Standards

Refrigerator

Air Conditioner

Television

Domestic Fan

Lighting

(a) one-door

(a) two-door

Singlesplitwallmountedairconditionercapacityupto25,000Btu/h

Thetypeof televisionareofthefollowinglistandofsizeuptoorequalto70inches:

(a)plasma

(b)liquidcrystal display(LCD)

(c)lightemitting diode(LED)

(d)cathoderay tube(CRT)

(a)wall

(b)desk

(c)pedestal

(d)ceiling

(a)fluorescent

(Doublecap fluorescent)

MS2595:2014

MS2597:2014

MS2576:2014

MS2574:2014

MS2598:2014

2Star

2Star

2Star

2Star

TubularFluorescent:

T8 18-31 70 ≥31 80 T5 ≥14<15 75 ≥15 80

Type (W) MEPS (lm/W)

RefertoStandard

RefertoStandard

RefertoStandard

RefertoStandard

NIL


31

MEPS Value Efficiency RatingsNo Equipment Type of Equipment

MEPS Standards

(b)Selfballasted singlecapped [compact fluorescent lamp(CFL)

c)Singlecapped fluorescent lamp(non- integrated compact fluorescentlamp) &circular fluorescentlamp

d)Selfbalasted lightemitting diode(LED)

(e)incandescent

MS2598:2014

MS2598:2014

MS2598:2014

MS2598:2014

Compactfluorescentlamp(CFL):

Lightemittingdiode(LED):

incandescent:

<9 46 ≥9<15 52 ≥15<25 55 ≥25 62

Lamp MEPS rating(W) (lm/W)

<10 46 ≥10<19 55 ≥19<27 59 ≥27 70

Lamp MEPS rating(W) (lm/W)

G13 75 GU10 50 E27/B22d 60 E14 60

LampCap MEPS Type (lm/W)

Incandsescent 20Lamp**

Type MEPS (lm/W)

**The Minimum Energy Performance Standards (MEPS) value for incandescent lamp shall not apply for the following use: a. components in electrical appliances; b. medical and lab equipment; c. internal decoration, shows and exhibition; d. safety and signaling; e. conservation of animals and as repellant for insects; f. heating and testing; g. cleanliness and health; h. beauty treatment; i. lamps that cannot be directly replaced with other type of lamp; and j. incandescent lamp for other purposes deemed suitable by the Commission to be excluded.

NIL


32

CHAPTER 6

APPLICATION FOR CERTIFICATE OF APPROVAL FOR ELECTRICAL EQUIPMENT

ELECTRICAL EQUIPMENT

In improving its delivery services, the Energy Commission (ST) has developed an online sys-tem for application ofCertificate ofApproval (CoA) for the importation andmanufacture ofhousehold electrical equipment. Effective 1st October 2010, all applications are done online via e-Permit system operated by DagangNet Technologies Sdn. Bhd. (DagangNet).

To import household electrical equipment, applicants or their local agents need to register with DagangNet. Once registered, applicants can proceed to apply electronically. Applicants are re-quiredtoapplyfortheCertificateofRegistrationtoManufacture/ImportbeforehecanproceedwiththeCertificateofApproval(CoA)application.STwillissuetheCoAifapplicationsareinorder (test report and all required documents submitted and fees paid to ST).

e-Permit is available at http://epermit.dagangnet.com as follows:-

E-Permit screen

TheprocessofCoAsapplicationisasshowninthefollowingflow-chart:-


33

6.1 NEW Application for CoA (Import/Manufacture)

ApplicantregisterswithDagangnet

ApplyCoR

CoRIssued

AttachTypeTestReportforMEPS(PerformanceTest

Report)

ApplicationRejected

Yes

Yes

No

No

No

No

Yes

Yes

OnlineapplicationthroughePermit.

Applicantfills-upinformationsuchas:- • Nameofelectricalequipment • Brand • ModelApplicant can refer to Trader Module User Guide

AttachedTypetestreport[fortestreportaccreditedbyAPLAC/ILACneedtogetapprovalfromDSMpriortoapplication submission]

RegisteredwithST

MEPSProducts

CorrectInformationgiven

ProcessFeeRM30.00

Paid

CoR = Certificate of Registration to Manufacture/Import (see Appendix A)DSM = Department of Standard Malaysia


34

No

Yes

No

Yes

Complete

Paid

EnergyCommission(ST)evaluatesbasedon: • ValidityofTypetestreport > SIRIMQAS;or > labsunderSAMMbyDSM;or > labsunderIECEECBScheme;or > labsaccreditedbyAPLACMRA;or > labsaccreditedbyILACMRA;or > labslistedunderASEANEEMRA. • NationalDeviation

CoAFees:-

• SinglephaseRM220.00 • ThreephaseRM330.00

CoA issued

Applicationre-submitted


35

Yes

Yes

PassedPassedFailedFailedConsignmentor

PCSPCS

MEPSProducts

i.STissueslettertoapplicantasto: •informthecancellationofCoA •equipmenttobesentto countryoforiginordestroyedii.CustomswillbeinformedofthecancellationofCoA

EquipmentaffixedwithSIRIM-STLabel

EquipmentaffixedwithSIRIM-STLabel&**EELabel

**TheartworkforEElabelcanbe obtainedbyEC;PleaserefertoChapter8andChapter9fordetails.

Equipmentshallbesentfor ConsignmentTestorPCSbySIRIM

EquipmentshallenterPCSbySIRIM

SIRIMinformST

Importer Manufacturer

Applicanttore-apply

*Please refer details explanation in Appendix B


36

6.2 RENEWAL Application for COA (Import/Manufacture)

RegisteredApplicant

ApplyCoR

RenewalofCoRissued

ValidityofMEPStypetest

report

Yes

Yes

No

No

No

NO

Yes

Yes

Onlineapplicationthroughe-Permit.Documentsrequiredare:- • ProofofpurchaseofSIRIMLabel;and/or • PCSApplicantcanrefertoTraderModuleUserGuide

EnergyCommission(ST)evaluatesbasedonvalidityof:- • ProofofpurchaseofSIRIMLabel;and/or • PCS • ValidityofTypetestreport

CoRstillvalid

MEPSProducts

Complete

Applicanttore-submit

RENEWALofCoAFees:-• SinglephaseRM110.00• ThreephaseRM220.00

Paid

CoR = Certificate of Registration to Manufacturer/Importer (See Appendix A)


37

Yes

Yes

PassedPassedFailed FailedConsignmentor

PCSPCS

MEPSProducts

i.STissueslettertoapplicantto: •informthecancellationofCoA •sendequipmenttocountryof originordestroyedii.CustomswillbeinformedonthecancellationofCoA

EquipmentaffixedwithSIRIM-STLabel

EquipmentaffixedwithSIRIM-STLabel&**EELabel

**TheartworkforEElabelcanbe obtainedbyEC;PleaserefertoChapter8andChapter9fordetails.

*PleasereferdetailsexplanationinAppendix C

Equipmentshallbesentfor ConsignmentTestorPCSbySIRIM

Equipmentshallre-enterPCSbySIRIM

RENEWED CoA issued

SIRIMinformST

Importer Manufacturer

Applicantsre-apply


38

6.3 Application for CoA for EXHIBITION purposes

ApplicanttoregisterwithDagangNet

ApplyCoR

CoRissued

Yes

No

No

No

Yes

Yes

Onlineapplicationthroughe-Permit.Applicantfill-upinformationonitemsrelatedtoexhibitionsuchas:- • Nameofelectricalequipment • Name • Placeandaddress • Date • DurationApplicantcanrefertoTraderModuleUserGuide

RegisteredwithST

CorrectInformation

ProcessFeeRM30.00

Paid

CoR = Certificate of Registration to Manufacturer/Importer (see Appendix A)

ApplicationRejected

Applicantre-applies


39

EnergyCommission(ST)evaluatesbasedon: • Invoice;and • AirWayBill(AWB);or • BillofLading(BL).

CoAforEXHIBITIONFeeRM220.00

Complete

Paid

CoA EXHIBITION issued

Equipmentapprovedisintendedtobedisplayedonly.Itshouldbe:-

• NOTtobesold,installedor used; • Re-exported(returnedto countryoforigin).

PleasereferdetailsexplanationinAppendix D

Applicationtobe

re-submitNo

No

Yes

Yes


40

CHAPTER 7

APPLICATION FOR RELEASE LETTER (RL)

ApplicantstoregisterwithDagangNet

Yes

No

No

No

No

Yes

Yes

Yes

Onlineapplicationthroughe-Permit.

ApplicanttochoosetypeofRL:- • RegulatedEquipment > FactoryResearch > QualityResearch > SpecificPurpose > Transit > ImportComponentforLocalMarket > ImportComponentfor100%Export > Re-workandRe-export > Concert • Non-RegulatedEquipmentApplicant can refer to Trader Module User Guide

Registered

CorrectInformation

EnergyCommission(ST)evaluatesbasedoneachtypeofRLoneachrequirementasinAppendix E.

RL issued

Complete

Comply

ApplicationRejected

PleasereferdetailsexplanationinAppendix E

ApplicationRejected

Applicantre-apply


41

No Items Requirements

1.

2.

NominalVoltagesandFrequency

VoltagesandFrequencyMarkingforRegulatedEquipment

a) NominalVoltageEffective 1st Jan 2008, nominal voltage for lowvoltage supply inMalaysia is230/400V (+10%, -6%) inaccordancewithMS IEC60038.Thedetailsofvoltagesandvariationsareasbelow:-

b) NominalFrequencyNominal frequency for lowvoltage supply voltage inMalaysia is al-lowedtofluctuateat±1%from50Hz.

Inlinewith(a)above,theelectricalequipmenttobeusedinMalaysiashallbedesigned tooperateat thecountry’snominalvoltageandfrequencyasfollows:

a)VoltageSingle-phaseequipmentshallberated/markedat230Vor240V.Iftheequipmentisratedwithmultipleorarangeofvoltages,voltagerangeof230V(+10%,-6%)shallbeincluded.

Three-phaseequipmentshallberated/markedat400Vor415V.Iftheequipmentisratedwithmultipleorarangeofvoltages,voltagerangeof400V(+10%,-6%)shallbeincluded.

Nominal Percentage of Voltage Voltage Variations (%) Variations (V) (V) + - Min. Max.Until 31/12/2007

Singlephase,1Ø 240 5 10 226 252

Threephase,3Ø 415 5 10 373.5 436

Commencing on 1/1/2008

Singlephase,1Ø 230 10 6 216 253

Threephase,3Ø 400 10 6 376 440

CHAPTER 8

REGULATORY REQUIREMENTS RELATED TO NATIONAL DIFFERENCES


42


3.

4.

TestingVoltageandFrequencyonElectri-calEquip-ment

Powersupplycordandmainplugrequire-ments

b)FrequencyProductshallberated/markedat50Hzandtestingshallbeconductedat50Hz(±1%).Iftheproductismarkedwith50/60Hzor50-60Hzthentestingshallbeconductedeitherat50Hzor60Hz,whicheverismoreunfavourable.

TypeTestReportforEquipmentThetestshallbeconductedbytheConformityAssessmentBody(CAB)atvoltagevariationsasinthetablebelow:

Singlephase,1Ø – 240V±6% : (225.6–254.4)V

Threephase,3Ø – 415V±6% : (390.1–439.9)V

Singlephase,1Ø – 230V±10% : (207–253)V

Threephase,3Ø – 400V±10% : (360–440)V

a) Voltage•Single-phaseequipmentTestingshallbeconductedbasedon230V(+10%,-10%)or240V(+6%,-6%)andotherrelevantvoltages,whenevertheequipmentismarkedwithmultipleorarangeofvoltages.

•Three-phaseequipmentTestingshallbeconductedbasedon400V(+10%,-10%)or415V(+6%,-6%),andotherrelevantvoltages,whenevertheequipmentismarkedwithmultipleorarangeofvoltages.

b)FrequencyTestingshallbeconductedeitherat50Hzor60Hz,whicheverismoreunfavourable.

Appliancesshallbefittedwithasuitableandappropriatelyapprovedpower supply cord andmainsplug. Both are regulated equipmentandmustbeapprovedbytheregulatorybodybeforeitcanbeusedwiththeappliances.a) ThePowerSupplyCordshallbecertifiedto:-

• MS2112-5orBSEN50525-2-11orIEC60227-5(PVCinsulated-flexiblecables/cords);or

• MS140orMS2127-4orIEC60245-1&IEC60245-4(Rubberin-sulated-flexiblecables/cords)

b) ThemainsPlugtobeusedinMalaysiashallbeasfollows:• 13AfusedplugcomplyingwithMS589-1orBS1363:PT.1;• 15AplugscomplyingwithMS1577;• 2.5A,250V,flatnon-rewireabletwo-poleplugwithcordforthe

connectionofclassIIequipmentcomplywithMS1578orBSEN50075.


43


5.

6.

ClassIandClassIIEquipment

RegulatedEnergyEfficiency(EE)Fansforper-formance

OnlyClassIwithsymbolasinFigure1andClassIIwithsymbolasinFigure2areallowedtobeusedinMalaysia.

Figure 1:ClassIFigure 2:ClassII

Class0andClass01appliancesasdefinedinMSIEC60335seriesorIEC60335seriesareNOTALLOWEDtobeusedinMalaysia.

a) Regulatedminimumenergyefficiencystandardsforelectricalfansnamelyceilingfans,wallfans,tablefans,pedestalfansandboxfanswhichusebladesareasfollows:

Minimum Co-efficient No Typeoffans ofperformance (COP) (m3/min/W)

1. CeilingFan 2.58 (1200mm/48inch–1500mm/60inch)

2. PedestalFan 1.01 (250mm/10inch–400mm/16inch)

3. Table/DeskFan 1.01 (250mm/10inch–400mm/16inch)

4. WallFan 1.01 (250mm/10inch–400mm/16inch)

5. BoxFan 0.5 (250mm/10inch–350mm/14inch)

Where, COP=AirDelivery(m3/min)InputWattage(W)

The test method used to determine COP is in accordance with MS 1220:2010 or IEC 60879:1986 with modification.

TheacceptablevalueofCOPmustbeatleastorabovethestatedvalueshown.

Note: Value of COP for No.1,2,3 & 4 are included in the MEPS requirements.


44

7. ComponentusedforFluorescentLampFitting


b) SuspensionSystemforElectricCeilingFans. Electricceilingfansmustbeprovidedwithaspecialwireasasec-

ondary suspension system. The testmethodused to check thatthe secondary suspension system of the electric ceiling fan hasadequatemechanicalstrengthisinaccordancewithMS1597:Part2-80orIEC60335-2-80withmodificationforceilingfanonly.

Standards for Fluorescent LampFitting areMS IEC60598-2-1or IEC60598-2-1(forfixedluminaries)andMSIEC60598-2-2orIEC60598-2-2(forrecessedluminaries).Componentssuchasglowstarter,starterholder,lampholder,capacitor,connectingdevice,ballastandinternalwiringareusedaspartofthefitting.Thus,thecomponentsusedforbothstandardsmentionedshallcomplytothefollowingstandards:

Components Standards

Glow-Starters MSIEC60155orIEC60155

Starterholder MSIEC60400orIEC60400

Lampholders MSIEC60400orIEC60400

Capacitors MSIEC61048orIEC61048 &MSIEC61049orIEC61049

Connecting MSIEC60998(Series)orIEC60998(Series)devices

Magnetic/ Safetytest:conventional MSIEC61347-1orIEC61347-1Ballast +MSIEC61347-2-8orIEC61347-2-8 and Performancetest: MSIEC141PT.2orIEC60921withmodification

Note : Ballast Watt Loss shall not be more than 6W for all fluorescent lamps ballast.

Electronic Safetytest:Ballast MSIEC61347-1orIEC61347-1 +MSIEC61347-2-3orIEC61347-2-3 and Performancetest: MSIEC60929withMSIEC61000-3-2 orIEC60929withIEC61000-3-2

InternalWiring MS 2112-3 or IEC 60227-3, MS 2112-4 or IEC60227-4

The insulatingmaterialof internalwiringmustbe capable of withstanding the maximum temperature to which it is subjected (heat resistance).


45

8.

9.

10.

11.

Manufacturingrequirements

Importingrequirements

ClimateConditions

RequirementsforMEPS

a) Manufactured regulated equipment shall participate in ProductCertificationScheme(PCS)bySIRIMandelectricalequipmentshallbeaffixedwithlabelissuedbySIRIMorbearSIRIMCertificationMark(un-derLabelLicensingProgramme).ThesampleofSIRIMlabelandSIRIMCertificationMarkcanbereferredinChapter9.

b)Manufacturersofproductssuchastelevision,refrigerator,domesticfanandairconditioner,mustalsoaffixtheEnergyEfficiencyLabelontotheproductsbeforeitcanbesoldtothecustomer.ThesampleofEn-ergyEfficiency(EE)labelisshowninFigure6inChapter9.

a) Imported regulated electrical equipment shall undergo Consign-mentTestconductedbySIRIMorparticipateinProductCertificationScheme(PCS)bySIRIM.

ElectricalequipmentwhichpassestheConsignmentTestshallbeaf-fixedwiththelabelsissuedbySIRIM.ThesampleofSIRIMlabelcanbereferredinChapter9.

ElectricalequipmentwhichfailstheConsignmentTestneedtobesenttothecountryoforiginorshallbedestroyed.

Electricalequipmentshallbeconstructedtobeusedwithpowersup-plycordandpowerplugwhichcomplywithMalaysia’srequirementsandstandards.

TherequirementsandstandardsofPowersupplycordandpowerplugarestatedasinitemNo.4above.

b)Importersofproductssuchastelevision,refrigerator,domesticfanandairconditioner,mustalsoaffixtheEnergyEfficiencyLabelontotheproductsbeforeitcanbesoldtothecustomer.ThesamplesofEnergyEfficiency(EE)labelareshowninFigure6inChapter9.

Apparatus to be used inMalaysia shall be subjected to tests undertropicalconditionsasspecifiedintherelatedstandards.

TomeettherequirementsoftheMEPS,theperformancecriteriawhentestedusingtherelevanttestingstandardshastobemet.Thetesting standards and performance criteria have been set as prescribed inChapter5A.



46

CHAPTER 9

LABELLING OR CERTIFICATION MARKA. Objective and rationale

Labelingormarkingof regulatedelectrical equipmentwill enable consumers todifferentiatebetween the approved and non-approved regulated electrical equipment. It also serves as adeterrentandameanstocheckfornon-approvedregulatedelectricalequipmentinthemarket.

B. Labeling or Marking

AllregulatedelectricalequipmentapprovedbytheCommissionmustbelabeledormarkedinaccor-dancewithregulation98oftheElectricityRegulations1994andshallbedoneinthemannerwhichhasbeendeterminedbytheCommissionasbelow:

i) Sticker Type TherearetwotypesofSIRIM-STlabelwhichshallbeaffixedontheequipment.

a) SIRIM-STlabel(BATCH) ImporterwhohaspassedConsignmentTestshallpurchaseSIRIM-STlabelandaffixon

eachofequipment.TheWordBATCHprintedonthe labelshowsthat the importedequipmentgonethroughBATCHConsignmentTest.Sampleofthelabelisasshownbelow:

NewSIRIM-STLabel OldSIRIM-STLabel (effective01-01-2015)

Figure 3:SIRIM-STlabelforImported

b) SIRIM-STlabel LocalmanufacturerandimporterwhohaveenteredPCSshallpurchaseSIRIM-STlabel

andaffixoneachequipment.Sampleofthelabelisasshownbelow:

NewSIRIM-STLabel OldSIRIM-STLabel (effective01-01-2015)

Figure 4:SIRIM-STlabelforLocallyManufacturedandImportedEquipment

BATCH


47

ii) Embossed Type

a) Formanufacturer or importerwhich participated in SIRIM-ST Label LicensingProgrammed,theymayusetheSIRIMCertificationMarkasshowninFigure5below.

SIRIMCERTIFIEDTOYY:XXXX

CERTIFICATIONNO:xxxxxxxx

SIRIM-STLabelLicensingProgramme

Figure 5:SIRIMCertificationMark

b) For small regulated electrical equipment such as lampholder, starterholder, glowstarterandcable1,SIRIMCertificationMarkshallbeembossintheirproducts.

Themanufacturer, importer, exhibitor, seller or advertiser is responsible to ensure that theregulated electrical equipment is affixed with appropriate label or SIRIM Certification Markwhicheverisapplicable.TheCommissionwillconductsurveillance/enforcementfromtimetotimeonmanufacturers’orimporters’premisesanddistributors’outlets.

C. WheretoaffixSIRIM-STlabelorSIRIMCertificationMark

TheSIRIM-STlabelorSIRIMCertificationMarkshallbeaffixedontheregulatedelectricalequipmentitselfinalegiblemanner.TheSIRIM-STlabelshallnotbeaffixedonthepackaging.

D. Requirement for Energy Efficiency (MEPS) Labelling

Productssuchastelevision,refrigerator,domesticfanandairconditionerarerequiredtoaffixwithEnergyEfficiencylabelbeforeitcanbesoldtotheconsumer.ThelabelasintheenergyefficiencylabelingguidelineshallbefollowedinaccordancetothefollowingspecificationasshowninFigure6below:-

(i) FontSpecification(ii) ColourSpecification(iii) 2-Starratinguntil5-Starrating

1DetailsembossoncableareSIRIMCert.mark/labs,standards,saizofcable,manufacture’scompany.


48

Figure 6: EnergyEfficiencyLabellingGuideline

D1. Size of EE label and requirement to display on the product

ManufacturerandImporterthathaveobtainCoArequiredtoprintouttheEElabelbyreferringtoEnergyCommissionguidelines.EELabellingguidelinesforMEPSproductsareasbelow:-

a) Air Conditioner• Sizeforairconditionersenergyefficiencylabelis9cm(width)X13.5cm(height).• Calculationguidelineshownasbelow:-

Colourspecification

height

width

A = Annual Energy Consumption (kWh) =

For Non-Inverter type:-365x8xPowerinput measured from the test report (kW)

For Inverter type:-365x8x(0.4xFull load power input measured (kW) + 0.6xHalf load power input measured (kW), from test report)

B = Energy consumption per year for the lowest 2-star rating model =

365x8x(Tested cooling capasity(kW) / EER lowers 2-star model)

Tested cooling capacity (W) = From test report EER lowers 2-star model =

9.56 Btu/hW(Cooling capacity <4.5kW) in W/W=(9.56x0.2931)=2.80 8.03 Btu/hW (4.5 kW < Cooling capacity <7.1 kW) in W/W = (8.03x0.2931)=2.35

Thus,B = 365x8x(Tested cooling capacity (kW) / 2.80) for Cooling capacity <4.5 kW

or

B = 365x8x(Tested cooling capacity (kW) / 2.35) for Cooling capacity <7.1 kW

Percerntage energy saving compared to the lowest 2-stars rating model =

100% - ((100x (A/B))


49

b) Domestic Fan• Sizeforfan’senergyefficiencylabelis4cm(width)X6cm(height).• Calculationguidelineshownasbelow:-

*Forceilingfan,theEElabelcanbelabelledonthe packaging.

Labelaffixed

Labelaffixed

A = Annual Energy Consumpion (kWh) =

365x8xPower input measured from the test report(kW)

B = Energy consumption per year for the lowest 2-star rating model (kWh) =

365x8x(Tested air delivery capacity (m3/min) COPLowest

2-stars model)1000

Tested air delivery capacity (m3/min)= From test report COPLowest 2-stars model=

2.58m3/minW(Ceiling fan)

1.01m3/minW(Pedestal, Wall and Desk fan)

Thus,B (kWh) = 65x8x(Tested air delivery capacity (m3/min) / 2.58)

1000 for Ceiling fan

or

B (kWh) = 65x8x(Tested air delivery capacity (m3/min) / 1.01)

1000

for Pedestal, Wall and desk fan

Percentage energy saving compared to the lowest 2-Stars rating model =

100% - ((100 x (A/B))


50

c) Refrigerator• Sizeforrefrigerator’senergyefficiencylabelis8cm(width)X12cm(height).• Calculationguidelinesshownasbelow:-

d) Television• Sizefortelevision’senergyefficiencylabelis7cm(width)X11cm(height).• Calculationguidelinesshownasbelow:-

Labelaffixed

e) Lighting• Declaredlumenperwatt(efficacy)andtestinghoursshallbeavailableatpackagingofthe individualproduct.

Labelaffixed

Annual Energy Consumption (kWh) = From test report

Annual Energy Consumption (kWh) = 365x Energy consumption per day in kWh (from test report)


100% - ((100x(EEFLowers 2-star model/EEFTested))

Where:-

EEFLowers 2-star model = 0.0016 x (Screen area,cm2) + 8.8

EEFTested = From test report


100% - ((100x(EEFLowers 2-star model/EEFTested))

Where:-

EEFLowers 2-star model = 1.028Vadjusted - 47.475 (1 door)

EEFLowers 2-star model = 0.307Vadjusted + 89.625 (2 door)

EEFTested = From test report


51

• ForLightEmittingDiode(LED)Lamps: 1) TheLumensmaintenancewillbecarriedoutevery1,000hoursuntilthecompletion of6,000hours.Aninterimreportwillbeissuedaftercompletingthefirst1,000hours. The interim report can be used for CoA application.The testwill be continued to completethe6,000hours.Afinalfulltestreportwillthenbeissuedtosupersedethe interimreport.

2) OncetheCoAhasbeen issued, theapplicant is requiredtostatetheEfficacyvalue ontothepackagingoftheproducttogetherwiththenumberofhourstheLEDhas beentestedasperexamplebelow:

i)Aftercompletingfirst1,000hourstest i)Aftercompletingfirst1,000hourstest

3) Iftheproductfailsafterthefirst1,000hoursbeforecompletingthe6,000hours,the testingbodyisrequiredtoinformEnergyCommissionofsuchfailure.TheEnergy

CommissionwillthennotapprovetheapplicationfortherenewaloftheCoA.

Efficacy Value: 55 Im/W

This product has been tested up to 1000 hours

Efficacy Value: 55 Im/W

This product has been tested up to 6000 hours


52

APPENDIxES


53

Appendix A

APPLICATION FOR CERTIFICATE OF REGISTRATION (CoR) TO MANUFACTURE / IMPORT

A. Application Procedure

1) Applicantswho require applying forCertificate of Approval (CoA) shall register asregistered manufacturer/importer with the Energy Commission.

2) Applicant has to ensure their registration as registered manufacturer/importer is valid prior to apply for CoA.

3) Registration can be made through e-DIK system http://edik.st.gov.my. The Energy CommissionwillissuethesuccessfulapplicantwithaCertificateofRegistration(CoR)to Manufacture/Import.

4) A CoR shall be valid for not less than 1 year and not exceeding 5 years from the date of issue or renewal.

5) Renewal of CoR shall be made within two (2) months before the expiry date and not less than 14 days before the expiry date.

6) Application for Renewal of CoR received less than 14 days before the expiry date will automatically be rejected. In this case applicant needs to apply for a new CoR.

7) Registered manufacturer/importer will be issued with Form V1 Certificate of Registration to Manufacture/Import as in Appendix F.

B. Documents Required

DocumentsrequiredforCertificateofRegistrationtomanufactureandimportareasfollows:

(i) Business Registration with Companies Commission of Malaysia (under Business Registration Act)

• CertificateofBusinessRegistration(FormD)andothersbusinessinformation;

or

(ii) CertificateofPrivateCompanyIncorporation(Form9) • Form 9, Form 24, Form 49 or latest form of Annual Return of a Company

C. Annual Fee

No Fee Imposed.


54

Appendix B

APPLICATIONFORCERTIFICATEOFAPPROVAL(CoA)TOMANUFACTURE,IMPORT, DISPLAYORADVERTISEELECTRICALEQUIPMENT.


1) Applicant is required to apply for Certificate of Approval (CoA) through e-Permithttp://epermit.dagangnet.com.

2) ApplicantshallrefertoDagangNetTechnologiesSdnBhdfordetailsononlineregistrationsattollfree1-300-133-133.

3) ApplicantisrequiredtoapplyforCertificateofRegistrationpriortohim/herapplyingforCoA.

4) DetailsforapplicationtobearegisteredManufacturer/ImporterareasinAppendix A.5) Applicantshallcompletetheapplicationbyprovidingallinformationcorrectlyandattach

allrequireddocuments.6) InformationsuchasNameofElectricalEquipment,BrandandModelshallnotbecorrector

elseapplicationwillberejected.7) Detailed steps on application procedures are available at e-Permit website on Trader

ModuleUserGuide.8) TechnicaldocumentsrequiredforCoAtomanufactureandimportareasfollows:

• TypeTestReportvalidityperiodnotexceedfive(5)yearsfromthedateoftestingandshallnotlessthan12monthfromthedateofCoAapplicationorasprescribedbytheCommission;

• Listofcomponents;• Instructionmanual;• Technicalspecificationandcatalogue;and• Sampleoftheproduct,ifrequested.

9) ApplicantshallpayRM30.00asprocessingfee.

B. Type Test Report

(i) TypeTestReportsthatarerecognisedbytheCommissionshallbeproducedbyanyofthefollowinglaboratories:-

1) SIRIMQASInternationalSdn.Bhd.(SIRIM),Malaysia;or2) Laboratories under Laboratory Accreditation Scheme of Malaysia (SAMM) by

DepartmentofStandardsMalaysia(DSM)recognisedbyEnergyCommission;or3) Laboratoriesunder the IECEECBScheme.The listof the laboratories is available

fromthewebsitehttp:// www.cbscheme.org.TheCBtestreportneedstobeaccompaniedbyaCBtestcertificate;or

4) Laboratories (in the scope of its accreditation)which are accredited by theaccreditationbodythathavesignedtheAsiaPacificLaboratoryAccreditationCooperation(APLAC)MRA–http://www.aplac.org.ThetestreportneedstobeaccompaniedwithaconformationletterfromtheDSM;or


55

5) Laboratories (inthescopeof itsaccreditation)whichareaccreditedbytheaccreditationbodythathavesignedthe InternationalLaboratoryAccreditationCooperation(ILAC)MRA–http://www.ilac.org.ThetestreportneedstobeaccompaniedwithaconformationletterfromtheDSM;or

6) Laboratories(inthescopeofitsaccreditation)listedasDesignatedTestingLabora-tory(DTL)underASEANSectoralMutualRecognitionAgreementforElectricalandElectronicEquipment(ASEANEEEMRA);

(ii) Foritems(3),(4),(5)and(6),testingshouldincludethenationaldeviationinMalaysia.TherequirementsofnationaldeviationareasinChapter8.

(iii) TestreportmustbeineitherEnglishorMalaysianlanguage.

C. Annual Fee for New ApplicationAnannualfeeofRM220.00forsinglephaseandRM330.00forthreephaseshallbepaiduponapproval of the CoA as per Second Schedule, Part XIII, Regulation 97(4), Electricity(Amendment)Regulations2014.

D. Requirement For ManufactureElectrical equipment that has been approved formanufacturing shall participate in SIRIM’sProductCertificationScheme (PCS). The electrical equipment shall be affixedwith a labelissuedbySIRIMorbeartheSIRIMCertificationMark.

E. Requirement For ImporterElectricalequipmentthathasbeenapprovedfor import intoMalaysiashallcomplywiththeconsignmenttestbySIRIMforeachbatchorparticipateinSIRIM’sPCSwithinthevalidityperiodoftheCoA.Theelectricalequipmentshallbeaffixedwith labels issuedbySIRIMorbeartheSIRIMCertificationMark.ElectricalequipmentwhichfailedtheConsignmentTestneedtobesentbacktothecountryoforiginorshallbedestroyed.Electrical equipment shall be constructedwith power supply cord andpower plugwhichcomplywithMalaysianrequirementsandstandards.

The requirements and standards of Power Supply Cords and Power Plugs are as stated in Chapter8,No.4.


56

Appendix C

RENEWALOFCERTIFICATEOFAPPROVAL(CoA)TOMANUFACTURE,IMPORT,DISPLAYORADVERTISEELECTRICALEQUIPMENT

RenewalofCoAshallbemadenot less than14daysbefore itsexpirydateas requiredunderregulation106ofElectricalRegulations1994.


1) Applicant (registeredManufacturer / Importer) is required to apply for Renewal of CoAthroughe-Permit.

2) ApplicantwhosepreviousCertificateofRegistrationhasexpiredisrequiredtore-applywithproceduresasinAppendix A.

3) AllapprovedCoAwillbedisplayedate-PermitandapplicantsmayrenewCoAbyselectingthepreviousJobNumberorApplicationID.

4) Applicantshallcompletehis/herapplicationbyprovidingall informationcorrectlyandattachingallrequireddocuments.

5) Unwantedmodelsshallbedeleted/removedfrome-PermitbeforesubmittingtherenewalapplicationforCoAtoEnergyCommission(ST).

6) Applicationwillberejected ifunwantedmodelsareNOTremovedfrome-Permit. InthiscaseapplicantneedstoapplyforanewCoA.

7) RenewalofCoAshallbemadewithintwo(2)monthsbeforetheexpirydateandnotlessthan14daysbeforetheexpirydate.

8) Application for Renewal of CoA received less than14daysbefore the expirydatewillautomaticallyberejected.InthiscaseapplicantneedstoapplyforanewCoA.

B. Technical documents required are: 1) LatesttestreportfromtestinglaboratoriesrecognisedbytheCommission.2) TypeTestReportvalidityperiodnotexceedfive(5)yearsfromthedateoftestingandshall

notlessthan12monthfromthedateofCoAapplicationorasprescribedbytheCommission;3) InthecaseofrenewalapplicationforCoAtoimport,theproofofpurchaseofSIRIM’slabel

fortheperiodofimportingandconsignmentinvoiceorcopyofconsignmenttestreportissuedbySIRIMarerequired.

4) InthecaseofrenewalapplicationforCoAtomanufacture,theproofofpurchaseofSIRIM’slabelorcopyofvalidProductCertificationlicenseissuedbySIRIMarerequired.

C. Annual Fee for Renewal of CoAAnannualfeeofRM110.00forsinglephaseandRM220.00forthreephaseproductsshallbepaiduponapprovaloftheCoA.

D. Requirement For ManufactureThemanufacturerofElectricalequipmentthathasbeenapprovedformanufactureshallalsorenewhisSIRIM’sPCS.TheelectricalequipmentshallbeaffixedwithlabelsissuedbySIRIMorbeartheSIRIMCertificationMark.

E. Requirement For ImportingElectricalequipmentthathasbeenapprovedforimportintoMalaysiashallcomplywiththecon-signmenttestbySIRIM’sforeverybatchorparticipateinSIRIM’sPCSwithinthevalidityperiod


57

oftheCoA.TheelectricalequipmentshallbeaffixedwithlabelsissuedbySIRIMorbearSIRIMCertificationMark.ElectricalequipmentwhichfailstheConsignmentTestneedtobesentbacktothecountryoforiginorshallbedestroyed.Electrical equipment shall be constructed with power supply cord and power plug which complywithMalaysia’srequirementsandstandards.TherequirementsandstandardsofPowerSupplyCordandPowerPlugareasstatedinChapter8,No.4.


58

Appendix D

APPLICATIONFORCERTIFICATEOFAPPROVAL(CoA)FOREXHIBITIONPURPOSES


1) Applicant is required to apply for a CoA for Exhibition through e-Permit http://epermit.dagangnet.com.

2) ApplicantisrequiredtoapplyforCertificateofRegistrationpriortohim/herapplyingforCoA.

3) Details for applications to be registered Manufacturer/Importer can be referred in Appendix A.

4) Applicantshallcompleteapplicationbyprovidingall informationcorrectlyandattachallrequireddocuments.

5) InformationsuchasNameofElectricalEquipment,BrandandModelshallbecorrectorelseapplicationwillberejected.

6) Detailed steps on application procedures are available at e-Permit website on TraderModuleUserGuide.

7) TechnicaldocumentsrequiredforCoAforExhibitionpurposesare: i) ACoverlettertospecify: Name,place,address,exhibitiondateandlengthofexhibitionorofferletterto participateintherelatedexhibition. ii) TheInvoiceandAirWayBill(AWB)forimportationbyairorBillofLading(BL)for

importationbyseashouldbemadeavailable.8) ApplicantshallpayRM30.00asprocessingfee.

B. Exhibition Fee

ExhibitionFeeofRM220.00shallbepaiduponapprovaloftheCoA.

C. Requirement for CoA for Exhibition Purposes

Equipmentapprovedisintendedtobedisplayedonly.Itshallbe:-• NOTtobesold,installedorused;• re-exportedorreturnedtocountryoforiginafterexhibition.


59

Appendix E

APPLICATIONFORRELEASELETTER(RL)


1) TheEnergyCommission(ST)willissueaReleaseLettertoCustomsasblanketapprovalforexemption fromCertificateofApproval (CoA) for importationofST’s regulatedelectricalequipment.

2) Release Letter is applicable for Special Purpose, Concert, Factory Research,QualityResearch, Re-Work and Re-Export, Imported Components used for EquipmentManufacturedfor100%ExportorLocalMarketandTransit.

3) Fornon-regulatedequipment,applicantmayrequestReleaseLetterforCustomsclearancepurposes.

4) ApplicationofReleaseLettershallbeapplythroughe-Permitathttp://epermit.dagangnet.com

5) Applicant shall complete applicationbyprovidingall information correctly andattachrequireddocuments.

6) InformationsuchasNameofElectricalEquipment,BrandandModelshallbecorrectorelseapplicationwillberejected.

B. Fee for Release Letter

ThereisnofeeimposedforReleaseLetter.

C. Technical Documents Required

1. Regulated Equipment for CoA Exemption i) SpecificPurpose-OilRig,Tanker,SIRIMTest,ElectricFenceEtc.

• Coverlettertospecifythepurposeofimport,nameandaddressofuseraswellasplaceofuse,

• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) forimportationviaseashouldbemadeavailable.

• AllapplicationsaresubjectedtoEnergyCommission’sapproval.

ii) Concert• Theimportedequipmentshallnotbesold,advertisedandexhibitedandmustbe

re-exportedaftertheconcert.• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) for

importationviaseashouldbemadeavailable.• Equipmentcatalogueshouldalsobemadeavailable.

iii) FactoryResearch• The imported sample shall not be sold, advertised or exhibited and the sample

mustbedisposedaftertheendoftheresearch.• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) for


60

importationviaseashouldbemadeavailable.• Amaximumof 10 units permodel is allowed for factory research. A copy of

manufacturinglicenseshouldalsobemadeavailable

iv) QualityResearch• The imported sample shall not be sold, advertised or exhibited and the sample

mustbedisposedafterendofresearch.• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) for

importationviaseashouldbemadeavailable.• Amaximumof4unitspermodelisallowedforqualityormarketresearch.

v) RepairAndRe-Export• Theimportedsampleshallnotbesold,advertised,exhibitedandthesamplemust

bere-exportedafterrepair• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) for

importationviaseashouldbemadeavailable.• Exportinvoiceasproofthatthemanufacturedequipmenthasbeenre-exported;• Manufacturinglicenseshouldbemadeavailable.

vi) ImportedComponentsUsedForEquipmentManufacturedFor100%Export• Letterofconfirmationthatthecompletedequipmentwillbefullexported.• AcopyofLicenseofManufacturingWarehouse(LMW)manufacturinglicensewith

relatedappendicesortaxexemptionletterfromtheMinistryofFinance/MIDAortaxexemptionletterfromtheRoyalMalaysianCustomsDepartment.

vii) ImportedComponentsUsedForEquipmentManufacturedForLocalMarket• AcopyofCoAtoManufactureforequipmentwhichuses importedcomponents;

and• Test reports as proof that the components to be imported are required for the

equipmenttobemanufactured.

viii) TransitPurposes• Coverlettershouldspecify: a. nameandaddressofBondedCustomsWarehousewhereimportedequipment

willbeplaced,includingthenameandtelephonenumberoftheofficertobecontacted;and

b. equipmentwill100%re-exportedtotherelatedcountry.Thecountryshouldbenamed.

• InvoiceandAirWayBill (AWB) for importationviaairorBillofLading(BL) forimportationviaseashouldbemadeavailable

2. Non-Regulatedequipment • Equipmentcatalogue; • Testreport;and/or • Sampleifrequired


61

FORM V1(regulation 97C)

ELECTRICITY SUPPLY ACT 1990

CERTIFICATE OF REGISTRATION TO MANUFACTURE/ TO IMPORT*

TheEnergyCommissionherebycertifiesinpursuanceofsection4(k)oftheElectricitySupplyAct1990

that ……………………………………………………………….........................…………………………………

at ……………………………………………...........................................................………………………….

hassatisfiedtherequirementsoftheActandtheRegulationsmadethereunder.

TheEnergyCommissioncertifiesthattheabove-mentioned

…………………………………………………...…hasbeenregisteredandthisCertificateofRegistration

shall be valid for a period of ………. years(s) from the date of issue stated below.

Date of issue: …..............

Place: …......................

….........................…………….

Energy Commission

__________________________________________________________________________________

* Delete wherever appropriate

** Not less than one year and not more than five years.”.

Appendix F


62

FORM V(regulation 97)


CERTIFICATE OF APPROVAL

Inaccordancewithregulation97oftheElectricityRegulations1994,thisCertificateisissuedto............................…………………………………………………………………………….………….................

(name of importer)

at……………………………………………………..........................................................................................(address)

and approval is given to

Import display1 sell advertise *

the equipment, the description of which are set out below direct from ………….................…...……………………………………………………............................................................................................................

(name and country of manufacturer)

and the equipment is in compliance with:(a) Standard:...............................

(b) Type Test Report No: .......................................for a period of one year from the date of issue/renewal* shown hereunder subject to the following conditions:

(state)

Date of issue/renewal*: ....…………….…....... Expiry Date: ...……………...........Approval No:....................…………………..... Fee RM: ………………................

Description of Equipment

Equipment :.................................Trade Name:.................………………..............Type/Model:..............................………………..

SpecificationOfEquipmentVoltage..........……………………......Volts Power ......……………....... wattsFrequency........…………………......HzCurrent.......……………......Amp

.......................………….....Energy Commission

__________________________________________________________________________________1. Equipment approved is intended to be displayed only and not to be sold, installed or used. * Delete whichever is not applicable.

Appendix G


63

FORM W(regulation 97)


CERTIFICATE OF APPROVAL

Inaccordancewithregulation97oftheElectricityRegulations1994,thisCertificateisissuedto…………………………………………………………………………………….………….................

(name of holder’s company)

at…………………………………………………..................................................…………………(address)

and approval is given to-

manufacture display 1 sell advertise *

the equipment, the description of which is set out below direct from ….........................................................…. ………………………………….........................................................................................................…

(name of manufacturer)

……………………………………………………......................................................……..................…………(address of manufacturer)

and the equipment is in compliance with :(a) Standard:...............................

(b) Type Test Report No: .......................................for a period of one year from the date of issue/renewal* shown hereunder subject to the following conditions:

(state)

Date of issue/renewal*: ....………………...... Expiry Date:....………………….......Approval No:........................………………... Fee RM:........……………………......

Description of EquipmentEquipment :.................................Trade Name:.................................Type/Model:.................................

Specification Of EquipmentVoltage.......…………………..........Volts Power ....………………......... wattsFrequency....…………………........HzCurrent.....…………………….....Amp

..............…………..............Energy Commission

__________________________________________________________________________________1. Equipment approved is intended to be displayed only and not to be sold, installed or used. * Delete whichever is not applicable.

Appendix H


64

FORM U1(regulation 97B)


CERTIFICATE OF REGISTRATION AS CONFORMITY ASSESSMENT BODY

TheEnergyCommissionherebycertifiesinpursuanceofsection4(l)oftheElectricitySupplyAct1990

that ……………………………….............…………………………………………………………………............

at ………………………………………..……...........................................................……………………..........

hassatisfiedtherequirementsoftheActandtheRegulationsmadethereunder.

The Energy Commission certifies that the above-mentioned

………………………………………………………… has been registered and this Certificate of

Registration shall be valid for a period of ………................................... year(s) from the date of issue

stated below.

Date of issue: …..............

Place: …......................

….........................…………….

Energy Commission

__________________________________________________________________________________

* Not less than one year and not more than three years.”;

Appendix I


65

Appendix J

ACCEPTABLE AND NON-ACCEPTABLE 2-PIN MAINS PLUG

SOURCE: CEE 7: 1963 Standard Sheet XVI IEC 83: 1975 Standard C5NOTES: This plug is available in two profiles (see page 9) Version l : round plug Version ll : Flat plug, with insulating collar Intended to be fitted to class ll (double insulated) appliances 2.5 A, 250 V Two pole - no earth contact

OTHERRATINGS: NoneOUTLINE:Version ll :

TYPICAL PLUG:

ACCEPTABLE

SOURCE: CEE 7: 1963 Standard Sheet XVlI IEC 83: 1975 Standard C5

NOTES: Intended to be fitted to class ll (double insulated) appliances 2.5 A, 250 V Two pole - no earth contact

OTHERRATINGS: NoneOUTLINE:

TYPICAL PLUG:

UNACCEPTABLE

19.0

19.0

19.0

19.0

0.5

19.0

10mm

ACCEPTABLEANDNON-ACCEPTABLE2-PINMAINSPLUG

ACCEPTABLEANDNON-ACCEPTABLE2-PINMAINSPLUG