INSTALLATION INSTRUCTIONS FOR PART 99-7872

99-7872

APPLICATIONS

Honda Fit 2007-2008

KIT FEATURES

• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Mount Units Provision• Painted To Match Factory Dash

99-7872=Gray

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

A

Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket Set

1-800-221-0932 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION

www.metraonline.com

B D

E

C

F

WIRING AND ANTENNA CONNECTIONS (Sold Separately)Harness:• 70-1722 - Honda harness 2006-upAntenna Adapter:• 40-HD10 - Honda antenna adapter

2005-up

TOOLS REQUIRED:

Dash Disassembly- Honda Fit 2007-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2

Kit Assembly- Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TABLE OF CONTENTS

99-7872

*Note: Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWEREnhance your installation and fabrication skills byenrolling in the most recognized and respectedmobile electronics school in our industry.Log onto www.installerinstitute.com or call800-354-6782 for more information and take steps toward a better tomorrow.

99-7872 DASH DISASSEMBLY

HONDA FIT 2007-2008A

B

C

1

1

Unclip the (3) a/c control cablesbehind glove box. (Figure A)

Disconnect the negative battery terminal to prevent an accidentalshort circuit.

3

Squeeze sides of glove box then pullout and let hang to access cablesbehind it.

2

Remove (2) 8 MM bolts securing center panel then unclip, unplug and remove entire assembly including climate controls. (Figure C)NOTE: These bolts are accessed from underneath the climate controls. Figure C shows assembly alreadyremoved to show bolt location.

5

Remove (1) Phillips screw from thepanel on the bottom of the a/c controls then unclip and removethe panel. (Figure B)

4

Continue to kit assembly.

99-7872 DASH DISASSEMBLY

HONDA FIT 2007-2008D

PASSENGER AIRBAG

TUNEFOLDER

SEEK SKIP

CLOCK

A/C

E

F

REMOVERETAINING CLIPS

7

Unclip and remove the A/C & RearDefroster switches and the PassengerAir Bag Off Light and set them asidefor use during kit assembly. (Figure D)

Remove (8) Phillips screws securingthe climate control to the back of thefactory center panel. Remove climatecontrols and set aside for use duringkit assembly. (Figure E)

6

Remove the (7) metal retaining clipsfrom the factory center panel and setthem aside for use during kit assem-bly. (Figure F)

8

Continue to kit assembly.

2

3

99-7872 KIT PREPARATION

KIT PREPARATIONA

B

PASSENGER AIRBAG A/C

C

ATTACHRETAINING CLIPS

1

Attach the (7) retaining clips to theradio housing in the same location asremoved from the factory centerpanel. (Figure C)

Secure the climate controls into theradio housing using the factory hard-ware. (Figure A)

3

Snap the A/C & Rear Defroster switch-es and the Passenger Air Bag OffLight into the radio housing. (Figure B)

2

Continue to kit assembly.

99-7872 KIT ASSEMBLY

4

A

B

C

DIN MOUNT RADIO PROVISION WITH POCKET

Slide the DIN cage into the radio hous-ing and secure by bending the metallocking tabs outward. (Figure A)

1

Slide the aftermarket radio into the DINcage and until it snaps into place.(Figure B)

2

Snap the pocket into the radio housing.(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7872 KIT ASSEMBLY

5

A

B

C

ISO MOUNT RADIO PROVISION WITH POCKET

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)

1

Slide the radio into the radio housinguntil it snaps into place. (Figure B)

2

Snap the trim plate onto the front ofthe Radio Housing. (Figure B)

3

Snap the Pocket into the radio housing. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

99-7872 KIT ASSEMBLY

6

DOUBLE DIN RADIO PROVISION

Cut and remove the center bar fromthe radio housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)

2

Slide the Double DIN radio into theDDIN bracket/radio housing assemblyand secure the radio to the assemblyusing the screws supplied with theradio. (Figure C)

3

Snap the Double DIN trim plate ontothe front of the radio/housing assem-bly. (Figure C)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

C

99-7872 KIT ASSEMBLY

7

STACKED ISO MOUNT UNITS PROVISION

Cut and remove the center bar fromthe radio housing. (Figure A)

1

Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)

2

Slide the stacked ISO mount units intothe bracket/housing assembly andsecure the units to the assembly usingthe screws supplied with the units.(Figure C)

3

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

C

Snap the Double DIN trim-plate ontothe front of the radio/housing assem-bly. (Figure C)

4

99-7872 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

8

NOTES

9

99-7872

99-7872 INSTRUCTIONS

1-800-221-0932

REV. 05/12/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7872

www.metraonline.com