Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Environmentally SafeLow VOC formula withno odor.
DurableDoes not shrink,crack, or peel
HomeGuard Polymer Sealant is an adhesive/sealant based on STP-E Polymer chemistry. HomeGuard Polymer Sealant is waterproof and may be applied from 0° to 140° to damp or dry surfaces. Odor free, paintable with water based paints in one hour a�er application. Will not shrink, crack or peel. Contains no isocyanates or solvents. Our low VOC formula meets American and European safety and environmental regulations rgarding the emission of volatile organic compounds (VOCs). Available in 10.1 oz. cartridges.
HomeGuard Polymer Sealant can be used to seal windows, doors, column joints, gutters, vents and ducts, roofs, crown molding and trim, siding and most areas where a sealant is needed. It can also be used to produce a highly durable, waterproof, seamless, elastometric flashing membrane aroundwindows and doors. HomeGuard Polymer Sealant as an adhesive has a superior bond to most substrates, including porous and non-porous surfaces.
R
R
R
R
OX Engineered Products22260 Haggerty Road Suite 365Northville, MI 48167p. 1.800.345.8881f. 248.289.9955oxep.com
ApplicationsCan be applied intemperatures aslow as 0 F
R
Basic Visual Screening Pass No surface cracks, bond loss, staining or vehicle bleed Hardness (Shore “A” Hardness) Pass 5 lbs/inch (>90%cohesion) Slump PASS > 0.1 in Pass >0.1 in
Vehicle Migration Pass No vehicle migration from compound edge
Low Temperature Flexibility Pass No cracks or adhesion loss
Water Resistance Pass No voids, cracks, separation, or breakdown
Racking Pass No cohesion loss or loss of adhesion
AAMA 800-10 TEST RESULTS AAMA 800-10 Requirement
Technical Data for HomeGuard Polymer Sealant
• Low VOC formula
• Can be applied from 0 F -140 F • Waterproof - apply to dry, damp or wet surfaces
• 12 cartridges/box with detachable 4” nozzles
Attributes
• No odor
• Does not shrink, crack or peel
• Paintable with latex based paints
• Shelf Life: 12- months; stored 40 F - 80 F
o o
o o
®HomeGuard Polymer Sealant was tested in accordance with AAMA 800-10, voluntry specifications and test methods for sealants, to determine compliance wtih AAMA 800.3-10 specification for narrow joint seam sealers, Type 1.
Compatible with all Ox Flashing Products & contributes to HomeGuard Systems warranties® ®
R
InstallationTemporarily secure flap withHomeGuard Seam Tape. Tack W.R.B. flap temporarily with sheathing tape and fold flap over head flashing.
Apply a continuous bead ofHomeGuard Polymer Sealant caulk behind the top and side window flanges only
HomeGuard Flexible Butyl Flashing or HomeGuard 9” Flashing 1/4” Sill dam underflashing R.O. + 12”Extend up side jamb 6”
Arctic FlashHead flashing R.O. +2xwidth of flashing +2”
Arctic FlashR.O. +2x width of flashing – 1”
Titan or HomeGuardHousewrap
A. HomeGuard Flexible Butyl Flashing, Titan Butyl Flashing, Arctic Flash or HomeGuard RA-plus Flashing
B.
HomeGuard Polymer Sealant
C.
Arctic-Flash, Titan Butyl Flashing or HomeGuard RA-Plus Flashing
D.
Arctic-Flash, Titan Butyl Flashing or HomeGuard RA-Plus Flashing
HomeGuard Polymer Sealant page 1HomeGuard Polymer Sealant Page 2r