Page 1 of 3

AP 1552 ORDERING GUIDE:Updated on September 6, 2011

AP1552 AT A GLANCE

1552E (External Antennas)

1552H (Hazardous Location)

1552C (Cable Backhaul)

1552I (Integrated Antennas)

Antennas External External Integrated Integrated

CleanAir Yes Yes Yes Yes

ClientLink Yes Yes Yes Yes

Fiber SFP Yes Yes - -

PoE Out Port 1802.3af (e.g. for video)

Yes Yes - -

Cable Modem- DOCSIS 3.0- EuroDOCSIS 3.0

- - Yes -

Haz-LocationClass1 Div2/Zone 2

- Yes - -

Battery Backup Option Yes - - -

Power Options AC, DC, PoE2 AC, DC, PoE2 40-90 VACPower over Cable

AC, DC

Note 1- Power over Ethernet. When AP1552E/H is powered via PoE, the PoE-Out port is not active.Note 2- PoE-in is NOT 802.3af & would not work with PoE 802.3af-capable Ethernet switch. Requires dedicated Power-Injector (AIR-PWRINJ1500-2=)

Page 2 of 3

AP 1552 ORDERING GUIDE:Updated on September 6, 2011

AP1552E(External Antennas)

AP1552H(Hazardous Location)

AP1552C(Cable Backhaul)

AP1552I(Integrated Antennas) COMMENTS

Step 1. Select the Product ID (PID) AIR-CAP1552E-x-K9 AIR-CAP1552H-x-K9 AIR-CAP1552C-x-K9 AIR-CAP1552I-x-K9

Step2. - Determine the "x" Regulatory Domain - Determine Product Country Availability

AIR-CAP1552E-A-K9AIR-CAP1552E-C-K9AIR-CAP1552E-E-K9AIR-CAP1552E-K-K9AIR-CAP1552E-M-K9AIR-CAP1552E-N-K9AIR-CAP1552E-Q-K9AIR-CAP1552E-R-K9AIR-CAP1552E-S-K9AIR-CAP1552E-T-K9

AIR-CAP1552H-A-K9

AIR-CAP1552H-E-K9

AIR-CAP1552H-M-K9AIR-CAP1552H-N-K9

AIR-CAP1552H-S-K9

AIR-CAP1552C-A-K9

AIR-CAP1552C-E-K9

AIR-CAP1552C-N-K9AIR-CAP1552C-Q-K9

AIR-CAP1552I-A-K9

AIR-CAP1552I-E-K9AIR-CAP1552I-K-K9

AIR-CAP1552I-N-K9

1. Go to Table 3 (802.11abgn Mesh Access Points) of the Wireless LAN Compliance Status URL: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html#wp90062292. Look for name of country (Column 1) where this product will be deployed. 3. Ensure that the AP product & model-of-interest is available in said country by looking at checked cross box (Country/Product model)4. Replace "x" in PID of "Step 1" with "Regulatory Domain" letter of said country which is found in column 2 of Table 3.5. Log-On Ordering Tool (http://www.cisco.com/web/ordering/root/index.html) & enter PID.6. If product in desired country is not available, do NOT enter the order; it will be held up & not ....shipped. Contact your Cisco Acccount Manager.

Step 3. Select SW load version S155W8K9-12423JA S155W8K9-12423JA S155W8K9-12423JA S155W8K9-12423JA- To Date there is only one SW load available. This applies to all the AP1550 models.- SW is an option under the AP selection in the Configuration tool (at $0 charge).

Step 4. Order 3x Antennas per AP (if applicable)

AIR-ANT2547V-N AIR-ANT2547V-N n/aAntenna Integrated in AP

n/aAntenna Integrated in AP

- Currently the only configurable antenna available for the AP1552 is the (AIR-ANT2547V-N)- Ant. can also be ordered as a spare (AIR-ANT2547V-N=) (spares denoted by "=" at end of PID)- Typically when item is ordered as an "option" it is shipped in same box as AP.- Typically when item is ordered as a "spare" it is shipped in a separte box from the AP.- Three (3) of these antennas are needed for each of AP1552E or AP1552H- For AP1552C & AP1552I Antenna integrated into AP. No additional antennas needed.

Step 5. Order Mounting Kit AIR-ACCPMK1550= AIR-ACCPMK1550= AIR-ACCSMK1550= AIR-ACCPMK1550=

- The Wall/Pole-Mount-Kit (PMK) works on the AP1552E, AP1552H, and AP1552I- The PMK is ordered as a "Spare" (not as an option) and is shipped separately from the AP.- Do not use the older (AIR-ACCPMK1500=) or (AIR-ACCPMK1520=) PMK with the AP1552E/H/I.- The AP1552C inlcudes a "Strand Mount Kit" (SMK) "option" at $0 charge with the AP1552C- The AP1552C SMK "option" must be selected as part of the AP1552C config. when ordering.- The AP1552C SMK "option" is shipped in the same box as the AP1552C unit.- The AP1552C SMK can also be ordered as a spare for an additional charge (AIR-ACCSMK1550=)

Step 6. Select Powering Option - Note: some APs can be powered by more than one method (PoE, AC, DC)Step 6.1. If PoE, Select PoE-Injector AIR-PWRINJ1500-2= AIR-PWRINJ1500-2= n/a n/a - Note: The CAT5 cable is not sourced by Cisco.

Step 6.2. If AC, Select Power-Cable-Option (select only one of the three options)

AIR-CORD-R3P-40NA=AIR-CORD-R3P-40UE=AIR-PWR-ST-LT-R3P=

n/a n/aAIR-CORD-R3P-40NA=AIR-CORD-R3P-40UE=AIR-PWR-ST-LT-R3P=

(AIR-CORD-R3P-40NA=) AC power cord, 40 ft. (12.2 m) with North American plug termination(AIR-CORD-R3P-40UE=) AC power cord, 40 ft (12.2 m) with European unterminated end(AIR-PWR-ST-LT-R3P=) AC Power cord, 4 ft (1.2 m), connects to Street-Light power

Step 6.3. Select Battery Backup AIR-1520-BATT-6AH= n/a n/a n/a - Battery Backup Option. Do NOT use the (AIR-1520-BATT-6AH=) Battery with the AP1552H

Step 7. Select Fiber-Backhaul Option- Fiber or Ethernet backhaul needs to only be used on the Root Access Point (RAP)- Fiber Backhaul is not needed if AP is using Ethernet backhaul (RAP) or Mesh backhaul (MAP).

Step 7.1. Order REEL Installation Kit AIR-1520-FIB-REEL= AIR-1520-FIB-REEL= n/a n/a- REEL kit is optional but recommended. Used to wrap & guide extra fiber inside AP unit- Items 7.1 & 7.2 replace older (GLC-FE-100BX-URGD=) that inlcuded REEL kit & a 100BASE SFP

Step 7.2. Select Fiber SFP (select only one of the two options)

GLC-SX-MM-RGD=GLC-LX-SM-RGD=

GLC-SX-MM-RGD=GLC-LX-SM-RGD= n/a n/a

(GLC-SX-MM-RGD=) 1000BaseSX multi-mode Rugged SFP(GLC-LX-SM-RGD=) 1000BaseLX single-mode Rugged SFP (long reach)

Step 8. PMK Installation Tool AIR-BAND-INST-TL= AIR-BAND-INST-TL= n/a AIR-BAND-INST-TL=- This Pole-Mount-Kit (PMK) Installation Tool is to firmly install the PMK band around the pole.- Only one is needed per installation crew.

* n/a: Not Applicable

Additional Useful Sources of information on the Aironet 1550 Series:- Main Page: http://www.cisco.com/en/US/products/ps11451/index.html- Data Sheet: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps11451/data_sheet_c78-641373.html- Install & Upgrade Guides: http://www.cisco.com/en/US/products/ps11451/prod_installation_guides_list.html- Country Compliance (Table 3): http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html#wp9006229

PIDs above this row are Unique to AP1550 Series / PIDs Below this row apply to both AP1520 & AP1550 Series

4Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

Step 1: Select AP typeAIR-CAP1552E-x-K9AIR-CAP1552H-x-K9AIR-CAP1552C-x-K9AIR-CAP1552I-x-K9

Step 3 Select SW Option 1Option1: S155W8K9-12423JA

Step 2 Select Regulatory Domain “x”AIR-CAP1552E-A-K9 AIR-CAP1552E-N-K9AIR-CAP1552E-C-K9 AIR-CAP1552E-Q-K9AIR-CAP1552E-E-K9 AIR-CAP1552E-R-K9AIR-CAP1552E-K-K9 AIR-CAP1552E-S-K9AIR-CAP1552E-M-K9 AIR-CAP1552E-T-K9

See Table 3 of: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html

Step 4 Select Antenna Option 1Option1: AIR-ANT2547V-N (x3) option

AIR-ANT2547V-N= (x3) spare

Step 5 Order Wall/Pole/Street-light Mounting KitWall/Pole-Mount-Kit: AIR-ACCPMK1550=

NOTES:- Product ID (PID) ending with an “=“ sign indicates that

item is ordered as a “Spare” rather than as an “Option”

- Options are usually shipped in the same package with the AP or are already installed inside the AP before shipping.

1. Only one SW & Antenna options are available at this time

Step 6 Select Powering OptionPoE Injector: AIR-PWRINJ1500-2=

AC Cable: AIR-CORD-R3P-40NA=

AIR-CORD-R3P-40UE=

AIR-PWR-ST-LT-R3P=

Battery backup: AIR-1520-BATT-6AH=

Step 7 Select Fiber Backhaul OptionReel Kit: AIR-1520-FIB-REEL=

Fiber SFP: GLC-SX-MM-RGD=

GLC-LX-SM-RGD=

Step 8 Order Mounting Kit Installation-ToolInstall Tool: AIR-BAND-INST-TL=

5Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

Step 1: Select AP typeAIR-CAP1552E-x-K9AIR-CAP1552H-x-K9AIR-CAP1552C-x-K9AIR-CAP1552I-x-K9

Step 3 Select SW Option 1Option1: S155W8K9-12423JA

Step 2 Select Regulatory Domain “x”AIR-CAP1552H-A-K9 AIR-CAP1552H-N-K9AIR-CAP1552H-E-K9 AIR-CAP1552H-S-K9AIR-CAP1552H-M-K9

See Table 3 of: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html

Step 4 Select Antenna Option 1Option1: AIR-ANT2547V-N (x3) option

AIR-ANT2547V-N= (x3) spare

Step 5 Order Wall/Pole/Street-light Mounting KitWall/Pole-Mount-Kit: AIR-ACCPMK1550=

NOTES:- Product ID (PID) ending with an “=“ sign indicates that

item is ordered as a “Spare” rather than as an “Option”

- Options are shipped in the same package with the AP or are already installed inside the AP before shipping.

- Not available in Australia nor in Brazil (IECEx)

1. Only one SW & Antenna option are available at this time

2. AC Cable is un-terminated & is provided by the installer. This is the most commonly used powering option.

3. Battery option is NOT available on the AP1552H

Step 6 Select Powering OptionPoE Injector: AIR-PWRINJ1500-2=

AC Cable: n/a2

Battery: n/a3

Step 7 Select Fiber Backhaul OptionReel Kit: AIR-1520-FIB-REEL=

Fiber SFP: GLC-SX-MM-RGD=

GLC-LX-SM-RGD=

Step 8 Order Mounting Kit Installation-ToolInstall Tool: AIR-BAND-INST-TL=

6Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

Step 1: Select AP typeAIR-CAP1552E-x-K9AIR-CAP1552H-x-K9AIR-CAP1552C-x-K9AIR-CAP1552I-x-K9

Step 3 Select SW Option 1

Option1: S155W8K9-12423JA

Step 2 Select Regulatory Domain “x”AIR-CAP1552C-A-K9 AIR-CAP1552C-N-K9AIR-CAP1552C-E-K9 AIR-CAP1552C-Q-K9

See Table 3 of: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html

Step 4 Select Antenna Option 2n/a

Step 5 Order Strand Mounting Kit 3Strand-Mount-Kit: AIR-ACCSMK1550=

NOTES:- Product ID (PID) ending with an “=“ sign indicates that

item is ordered as a “Spare” rather than as an “Option”

- Options are shipped in the same package with the AP or are already installed inside the AP before shipping.

1. Only one SW option is available at this time

2. Antennas Integrated (Built-in)

3. Strand-Mount-Kit is at ($0) when ordered as an option with the AP1552C.

4. Power-over-Cable. No powering option is needed.

5. Backhaul-over-cable. No fiber backhaul option is available.

6. Tool is standard screw/nut installation equipment

Step 6 Select Powering Option 4

n/a

Step 7 Select Fiber Backhaul Option 5

n/a

Step 8 Order Strand Mount Kit Installation-Tool 6

n/a

7Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

Step 1: Select AP typeAIR-CAP1552E-x-K9AIR-CAP1552H-x-K9AIR-CAP1552C-x-K9AIR-CAP1552I-x-K9

Step 3 Select SW Option 1Option1: S155W8K9-12423JA

Step 2 Select Regulatory Domain “x”AIR-CAP1552I-A-K9 AIR-CAP1552I-K-K9AIR-CAP1552I-E-K9 AIR-CAP1552I-N-K9

See Table 3 of: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a.html

Step 4 Select Antenna Option 2n/a

Step 5 Order Wall/Pole/Street-light Mounting KitWall/Pole-Mount-Kit: AIR-ACCPMK1550=

NOTES:- Product ID (PID) ending with an “=“ sign indicates that

item is ordered as a “Spare” rather than as an “Option”

- Options are shipped in the same package with the AP or are already installed inside the AP before shipping.

1. Only one SW option is available at this time

2. Antennas Integrated (Built-in)

3. PoE option/ Power-Injector is NOT available on AP1552I

4. Battery option is NOT available on the AP1552I

5. Fiber option is NOT available on the AP1552I

Step 7 Select Fiber Backhaul Optionn/a5

Step 8 Order Mounting Kit Installation-ToolInstall Tool: AIR-BAND-INST-TL=

Step 6 Select Powering OptionPower Injectors:n/a3

AC Cable: AIR-CORD-R3P-40NA=

AIR-CORD-R3P-40UE=

AIR-PWR-ST-LT-R3P=

Battery: n/a4

8Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

1- Check 802.11abgn_Mesh_Access_Points section (Table 3); the Wireless LAN Compliance Status for the most up-to-date country compliance.http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps430_Products_Data_Sheet.html

9Cisco Confidential © 2011 Cisco and/or its affiliates. All rights reserved.

Additional Useful Sources of information on the Aironet 1550 Series:

- AP1550 Series Home Page: http://www.cisco.com/en/US/products/ps11451/index.html

- Data Sheet: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps11451/data_sheet_c78-641373.html

- Install & Upgrade Guides:http://www.cisco.com/en/US/products/ps11451/prod_installation_guides_list.html

- Country Compliance (Table 3):http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps430_Products_Data_Sheet.htm