AN

CHORING

D

OWELING

AN

CHORING

D

OWELING

ULTRABOND® HS-1CCHigh StrengthEpoxy Adhesive

GENERAL USES & APPLICATIONS

• Anchor in dry, water saturated, water-filled and submerged hammer drilled holes

• Suitable for core drilled installations in dry or water saturated concrete

• Muliple anchor types: threaded rod, rebar & internally threaded inserts

• OSHA Table 1 compliant drilling/cleaning method using Milwaukee Tool hollow vacuum bit system

www.atcepoxy.com 1.800.892.1880

ADVANTAGES & FEATURES

• IAPMO ER-591 evaluation report for use in cracked and uncracked normal weight and lightweight concrete

• Code Compliant in cartridge and bulk dispensing systems, IBC/IRC: 2018, 2015, 2012 & 2009

• Highest elevated temperature resistance of any ICC-ES AC308 and ACI 355.4 assessed anchoring epoxy on the market, up to 205 °F (96 °C) under short term loading conditions

• Made in the USA

STANDARDS & APPROVALSCODE COMPLIANT:IAPMO UES ER-591

IBC/IRC 2018, 2015, 2012 & 2009Florida Building Code 2017 & 2014

City of Los Angeles - Report Pending

Drinking Water System Components NSF/ANSI 61 & 372

AASHTO M235 / ASTM C881-15Type I, II, IV & V Grade 3 Class A, B & C

Nationally Department of Transportation (DOT)Approved or Pending

HIGHEST PERFORMINGANCHORING EPOXY

− PERIOD −

ER-591

The first and only Code Compliant anchoring adhesive approved for

bulk dispensing systems!

ATC Hilti ITW DeWalt

ER-591 ESR-3814 ESR-4057 ESR-2508 ESR-4046 ESR-3298

Threaded Rod, Rebar & Internally Threaded Inserts

Fast Full Cure @ 75 °F in 7 hours or less

Dry, Damp, Water-Filled and Submerged Holes

Concrete Gray Color

Highest Average Bond Strength

NSF / ANSI 61 & 372Drinking Water & Lead Free

Core-Drilled Holes (SD)

Cartridge & BulkCode Compliant

Highest Temperature Epoxy = 205 °F

Pure110+

Convenient 1:1 Mix Ratio

SET-3G

ICC AC308 & ACI 355.4 Tested and Assessed

ULTRABONDHS-1CC

RE 500 V3

Simpson

SET-XPRedhead

C6+

No Hole Cleaningw/Vacuum Drill Bits

Competitive Advantages

www.atcepoxy.com 1.800.892.1880Rev 112018

THE CHOICE IS CLEAR

Hilti is a registered trademark of Hilti Aktiengesellschaft Corporation | Simpson, SET-XP & SET-3G are registered trademarks of Simpson Strong-Tie Company, Inc. ITW Red Head is a registered trademark of Illinois Tool Works, Inc. | Pure110+ & DeWalt are trademarks of Stanley Black & Decker

Data Sources for Products in Illustrated Graphs: ER-591, Issued August 2018 | ESR-3298, Reissued July 2018 | ESR-3814, Revised May 2018 ESR-3577, Revised February 2018 | ESR-4046, Reissued September 2018 | ESR-4057, Issued April 2018 | ESR-2508, Reissued July 2018

For complete product information, please refer to the product TDS at www.atcepoxy.com.

BOND STRENGTH IN DRY CRACKED CONCRETE, THREADED ROD, 176 °F+ SHORT TERM

TEMPERATURE*, WITH SUSTAINED LOAD AND PERIODIC INSPECTION

HS-1CC Pure110+ RE 500 V3C6+

(2k Polymer)SET-3G

11.5% 41.5% 0.375 1,245 882 880 453 1,11710.7% 43.1% 0.625 1,245 882 870 453 1,1250.5% 22.7% 0.875 1,055 882 860 453 1,050

19.7% 38.3% 1.25 1,120 882 810 453 936

HS-1CC 13%Pure110+ 0%RE 500 V3 0%C6+ (2KP) 27%C6+ (2:1) 4%SET-3G 0%SET-XP 42%

HS-1CC 130 to 180 Max Temp:Pure110+ 140 to 176RE 500 V3 130 to 176C6+ (2KP) 130 to 176C6+ (2:1) 142 to 165SET-3G 160 to 176

SET-XP

Cracked Dry Concrete, Threaded Rod, Periodic Inspection, With Sustained Load, 176F+ Short Term

* Note: ITW C6+ (new 2:1) is limited to a maximum short term temperature of only 165 °F, and Simpson SET-XP is limited to a maximum short term temperature of only 150 °F, therefore neither meet the performance characteristics necessary in order to compare in this chart to the higher temperature performing products.

% Better than Hilti RE

500 V3

Anchor Size

180F with sust. Load

176F with sust. Load

176F with sust. Load

% Better than Simpson SET-

3G

Only Publish 1 Temperature Range(capped at 150F)

12%27%31%46%15%17%

176F with sust. Load

Reductions Due to Sustained Load

Reductions Due to Short Term Elevated Temperature

Temp Range A to B/C

176F with sust. Load

0

200

400

600

800

1,000

1,200

1,400

0.375 0.625 0.875 1.25

Bond

Str

engt

h (p

si)

Threaded Rod Diameter (inch)

Bond Strength in Dry Cracked Concrete, Threaded Rod, 176 °F+ Short Term

Temperature*, with Sustained Load and Periodic Inspection

HS-1CC

Pure110+

RE 500 V3

C6+ (old 1:1)

SET-3G

HS-1CC

Pure 110+

RE 500 V3

SET-3G

C6+ (old 1:1)

C6+ (new 2:1)

SET-XP

* Note: ITW C6+ (new 2:1) is limited to a maximum short term temperature of only 165 °F, and Simpson SET-XP is limited to a maximum short term temperature of only 150 °F, therefore neither meet the performance characteristics necessary in order to compare in this chart to the higher temperature performing products.

BOND STRENGTH IN DRY UNCRACKED CONCRETE, THREADED ROD, ≤ 160 °F SHORT TERMTEMPERATURE, NO SUSTAINED LOAD

AND PERIODIC INSPECTION

HS-1CC Pure110+ RE 500 V3C6+

(2k Polymer)C6+

(New 2:1)SET-3G SET-XP

16.2% 20.6% 0.375 2,870 1,829 2,380 1,350 2,470 2,192 1,33014.3% 19.7% 0.625 2,645 1,671 2,210 1,350 2,315 2,162 1,83012.0% 18.6% 0.875 2,420 1,567 2,040 1,350 2,160 1,967 1,5257.8% 16.2% 1.25 2,080 1,479 1,790 1,350 1,930 1,672 1,070

ReferencesComments

ESR-3298ESR-3814ESR-3577 27% increase without sustained loadESR-4046 4% increase without sustained loadESR-4057ESR-2508 42% increase without sustained load

160F w/o sust. Load% Better

than Hilti RE 500 V3

Uncracked Dry Concrete, Threaded Rod, Periodic Inspection, No Sustained Load, ≤ 160F Short Term

% Better than ITW C6+

Anchor Size

150F w/o sust. Load

140F w/o sust. Load

130F w/o sust. Load

Revised February 2018 ITW C6+ (2KP formula)Revised Sept. 6th, 2017 ITW C6+ (new 2:1 formula)Issued April 2018 Simpson SET-3G No difference in sustained vs. no sustainedRevised February 2018 Simpson SET-XP

150F w/o sust. Load

Revised February 2018 DeWalt Pure110+ No difference in sustained vs. no sustainedRevised December 2017 Hilti RE 500 V3 No difference in sustained vs. no sustained

130F w/o sust. Load

142F w/o sust. Load

0

500

1,000

1,500

2,000

2,500

3,000

0.375 0.625 0.875 1.25

Bond

Str

engt

h (p

si)

Threaded Rod Diameter (inch)

Bond Strength in Dry Uncracked Concrete, Threaded Rod, ≤ 160 °F Short Term

Temperature, No Sustained Load and Periodic Inspection

HS-1CC

Pure110+

RE 500 V3

C6+ (old 1:1)

C6+ (new 2:1)

SET-3G

SET-XP

ULTRABOND®HS-1CCER-591

RE 500 V3ESR-3814

SET-3GESR-4057

SET-XPESR-2508

RedheadC6+

ESR-4046Pure 110+ESR-3298

HS-1CC

Pure 110+

RE 500 V3

SET-3G

C6+ (old 1:1)

7 hours