Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
AM\905004EN.doc PE491.113v02-00
EN United in diversity EN
EUROPEAN PARLIAMENT 2009 - 2014
Committee on the Environment, Public Health and Food Safety
2011/0409(COD)
12.6.2012
AMENDMENTS95 - 143
Draft reportMiroslav Ouzký(PE487.891v02-00)
Proposal for a Regulation of the European Parliament and of the Council on the sound level of motor vehicles
Proposal for a regulation(COM(2011)0856 – C7-0487/2011 – 2011/0409(COD))
PE491.113v02-00 2/67 AM\905004EN.doc
EN
AM_Com_LegReport
AM\905004EN.doc 3/67 PE491.113v02-00
EN
Amendment 95Françoise Grossetête, Salvatore Tatarella
Proposal for a regulationAnnex I – point 5.2.2. a (new)
Text proposed by the Commission Amendment
5.2.2.a The limit values set forth in the table in Annex III apply with a reasonable tolerance margin during measurement.
Or. en
Justification
The current provisions in all noise regulations allow a tolerance for production.
Amendment 96Judith A. Merkies, Nessa Childers, Minodora Cliveta, Toine Manders, Andres Perello Rodriguez
Proposal for a regulationAnnex I Appendix 2 a (new)
Text proposed by the Commission Amendment
Appendix 2a Type approval values from vehicle and test data:1.Elements of capsulation1.1 Elements of noise encapsulation as defined by the vehicle manufacturer2. Noise level of moving vehicle:Test result (Lurban): dB(A)Test result (Lwot): dB(A)Test result (Lcruise): dB(A)kP – factor:
PE491.113v02-00 4/67 AM\905004EN.doc
EN
3. Noise level of stationary vehicle:Position and orientation of microphone (according to figure 2 in Appendix 1 of Annex II)Test result for stationary test: dB(A)
Or. en
Justification
Monitoring and reporting of EU type approval certificate.
Amendment 97Judith A. Merkies, Nessa Childers, Minodora Cliveta, Patrizia Toia, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 2.2.
Text proposed by the Commission Amendment
Compliance of the acoustic measurement instrumentation shall be verified by the existence of a valid certificate of compliance. Those certificates shall be deemed to be valid if certification of compliance with the standards was conducted within the previous 12-month period for the sound calibration device and within the previous 24 month period for the instrumentation system. All compliance testing must be conducted by a laboratory, which is authorized to perform calibrations traceable to the appropriate standards.
Compliance of the acoustic measurement instrumentation shall be verified by the existence of a valid certificate of compliance. Those certificates shall be deemed to be valid if certification of compliance with the standards was conducted within the previous 12-month period for the sound calibration device and instrumentation system. All compliance testing must be conducted by a laboratory, which is authorized to perform calibrations traceable to the appropriate standards.
Or. en
Justification
It is anomalous checks on sound instrumentation systems are only conducted every 2 years whilst those of sound calibration devices occur annually. This anomaly could lead to errors in sound instrumentation systems leading to incorrect measurements being conducted during tests. Device and instrumentation system calibration should be should be conducted together.
AM\905004EN.doc 5/67 PE491.113v02-00
EN
Amendment 98Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.1. – paragraph 4
Text proposed by the Commission Amendment
The meteorological instrumentation should be positioned adjacent to the test area at a height of 1.2 m ± 0.02 m. The measurements shall be made when the ambient air temperature is between +5 °C and +40 °C.
The meteorological instrumentation should be positioned adjacent to the test area at a height of 1.2 m ± 0.02 m. The measurements shall be made when the ambient air temperature is between +5 °C and +25 °C.
Or. en
Justification
Vehicles emit less noise at higher ambient meteorological temperatures. The lower range of values will reduce gains by vehicle manufactures artificially lower test results.
Amendment 99Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.1. – paragraph 7
Text proposed by the Commission Amendment
Any noise peak which appears to be unrelated to the characteristics of the general noise level of the vehicle shall be ignored in taking the readings.
deleted
Or. en
Justification
All noise peak should be considered in readings.
PE491.113v02-00 6/67 AM\905004EN.doc
EN
Amendment 100Gilles Pargneaux
Proposal for a regulationAnnex II – point 3.1. – paragraph 7
Text proposed by the Commission Amendment
Any noise peak which appears to be unrelated to the characteristics of the general noise level of the vehicle shall be ignored in taking the readings.
deleted
Or. fr
Justification
All noise peaks should be taken into account when readings are taken.
Amendment 101Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Toine Manders, Marita Ulvskog, Asa Westlund, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.1. – paragraph 9
Text proposed by the Commission Amendment
The background noise (including any wind noise) shall be at least 10 dB below the A-weighted noise pressure level produced by the vehicle under test. If the difference between the ambient noise and the measured noise is between 10 and 15 dB(A), the appropriate correction must be subtracted from the readings on the noise-level meter in order to calculate the test results, as in the following table:
The background noise (including any wind noise) shall be at least 15dB below the A-weighted noise pressure level produced by the vehicle under test.
1/ In conformity with Annex VII to this Regulation.
Or. en
AM\905004EN.doc 7/67 PE491.113v02-00
EN
Justification
The amendment is designed to reduce flexibility in the test and reducing gains by manufactures.
Amendment 102Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Toine Manders, Marita Ulvskog, Asa Westlund, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.1. – table
Text proposed by the Commission
Difference between ambient noise and noise to be measured dB(A)
10 11 12 13 14 15
Correction dB(A) 0.5 0.4 0.3 0.2 0.1 0.0
Amendment
deleted
Or. en
Justification
The amendment is designed to reduce flexibility in the test and reducing gains by manufactures.
Amendment 103Christofer Fjellner
Proposal for a regulationAnnex II – point 3.2.1. – introductory part
Text proposed by the Commission Amendment
3.2.1. The vehicle tested shall be selected in a way so that all vehicles of the same type which are put on the market fulfil the requirements of this Regulation.
3.2.1. The vehicle tested shall be representative of vehicles to be put on the market as specified by the manufacturer.
Or. en
PE491.113v02-00 8/67 AM\905004EN.doc
EN
Justification
The current provisions in all noise regulations allow a tolerance for production.
Amendment 104Françoise Grossetête
Proposal for a regulationAnnex II – point 3.2.1. a (new)
Text proposed by the Commission Amendment
3.2.1a. The vehicle tested shall be representative of vehicles to be put on the market, as specified by the manufacturer.
Or. en
Justification
Selection of vehicles for the test shall be done in a way to enable a practicable choice for testing. The proposed text will require manufacturer to select the loudest vehicle within a family for the type test, which is very often for practical reasons not possible. The obligation of the manufacturer to ensure that any vehicle put on the market satisfies the specifications of the Regulation is done in article 5 point 1.
Amendment 105Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.2.1. – table – row 4 'Vehicle category N2, N3 – paragraph 1
Text proposed by the Commission Amendment
Extra loading to reach the test mass of the vehicle shall be placed above the driven rear axle(s). The extra loading is limited to 75 per cent of the maximum mass allowed for the rear axle. The test mass must be achieved with a tolerance of ± 5 per cent.
Extra loading to reach the test mass of the vehicle shall be placed above the driven rear axle(s). The extra loading is limited to 75 per cent of the maximum mass allowed for the rear axle.
AM\905004EN.doc 9/67 PE491.113v02-00
EN
Or. en
Justification
The test mass should not have any tolerance.
Amendment 106Satu Hassi
Proposal for a regulationAnnex II – point 3.2.2.
Text proposed by the Commission Amendment
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. 2/ The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall represent the tyres with the highest sound emission of that type identified by manufacturersand shall be recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. 2/ The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
Or. en
Amendment 107Miroslav Ouzký, Salvatore Tatarella, Martin Callanan
Proposal for a regulationAnnex II - point 3.2.2.
Text proposed by the Commission Amendment
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The
PE491.113v02-00 10/67 AM\905004EN.doc
EN
tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. 2/ The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. 2/ The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have legal tread depth.
Or. en
Amendment 108Toine Manders
Proposal for a regulationAnnex II – point 3.2.2.
Text proposed by the Commission Amendment
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall be representative for the axle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have a tread depth of at least 80 per cent of the full tread depth.
Or. en
AM\905004EN.doc 11/67 PE491.113v02-00
EN
Justification
The aim of the new test method is to simulate real urban traffic. The tread depth of the tyres and the tyre designation should be that typically used in traffic. The UNECE Recommendation is for a minimum tread depth of 80% of the full tread depth. The test should take into account that trucks use different tyre designations on front and rear axles. Furthermore the mandatory monitoring procedure for this new Regulation between 2007 and 2010 was based on tyres representative for the axle.
Amendment 109
Sabine Wils
Proposal for a regulationAnnex II – point 3.2.2.
Text proposed by the Commission Amendment
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
3.2.2. Tyre rolling sound emissions are laid down in Regulation (EC) No 661/2009 on the general safety of motor vehicles. The tyres to be used for the test shall represent the tyres with the loudest noise emission of that type identified by manufacturers for the vehicle and shall be selected by the vehicle manufacturer and recorded in Appendix 3 to Annex I of this Regulation. They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle. The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least legal tread depth.
Or. en
Justification
According to the principles of Regulation (EC) No 692/2008. The amendment is designed to ensure that all vehicles comply with standards and reduces gains of the test by manufacturers.
Amendment 110Salvatore Tatarella, Miroslav Ouzký, Françoise Grossetête
PE491.113v02-00 12/67 AM\905004EN.doc
EN
Proposal for a regulationAnnex II – point 3.2.2. – footnote 2/
Text proposed by the Commission Amendment
2/ Given that the tyre contribution foroverall sound emission is significant, regard must be had for existing regulatory provisions concerning tyre/road sound emissions Traction tyres, snow tyres and special-use tyres shall be excluded during type-approval- and conformity of production measurements at the request of the manufacturer in accordance with UNECE Regulation No. 117 (OJ L 231, 29.8.2008, p. 19).
2/ Given that the tyre contribution for overall sound emission is significant, regard must be had for existing regulatory provisions concerning tyre/road sound emissions. Traction tyres, snow tyres and special-use tyres shall be excluded during type-approval- and conformity of production measurements at the request of the manufacturer in accordance with UNECE regulation No. 117.
Or. en
Justification
The mention of OJ L 231 29.8.2008 should be deleted as it is an outdated reference.
Amendment 111Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point – 3.2.4.
Text proposed by the Commission Amendment
3.2.4. If the vehicle is fitted with more than two-wheel drive it shall be tested in the drive which is intended for normal use.
3.2.4. If the vehicle is fitted with more than two-wheel drive, it should be tested with the maximum number of driven wheels.
Or. en
Justification
Should the car be fitted with more than two-wheel drive, four-wheel drive, it should be tested in four-wheel drive mode.
AM\905004EN.doc 13/67 PE491.113v02-00
EN
Amendment 112
Sabine Wils
Proposal for a regulationAnnex II – point – 3.2.4.
Text proposed by the Commission Amendment
3.2.4. If the vehicle is fitted with more than two-wheel drive it shall be tested in the drive which is intended for normal use.
3.2.4. If the vehicle is fitted with more than two-wheel drive, it should be tested with the maximum number of driven wheels.
Or. en
Justification
Should the car be fitted with more than two-wheel drive, four-wheel drive, it should be tested in four-wheel drive mode.
Amendment 113Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Pavel Poc, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 3.2.6 a (new)
Text proposed by the Commission Amendment
3.2.6a. Testing shall be representative of real world noise emissions, by correcting limit values for trucks by -1 dB(A) to account for ultra-quiet tyres used in the test but never used on the road.
Or. en
Justification
Test should be representative of real-world drive conditions, test results affected by the use of silent tyres should be accounted for.
PE491.113v02-00 14/67 AM\905004EN.doc
EN
Amendment 114Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 4.1.2.1. – paragraph 1
Text proposed by the Commission Amendment
The path of the centreline of the vehicle shall follow line CC' as closely as possible throughout the entire test, from the approach to line AA' until the rear of the vehicle passes line BB'. If the vehicle is fitted with more than two-wheel drive, test it in the drive selection which is intended for normal road use.
The path of the centreline of the vehicle shall follow line CC' as closely as possible throughout the entire test, from the approach to line AA' until the rear of the vehicle passes line BB'. If the vehicle is fitted with more than two-wheel drive, it should be tested with the maximum number of driven wheels.
Or. en
Justification
Should the car be fitted with more than two-wheel drive, four-wheel drive, it should be tested in four-wheel drive mode.
Amendment 115Anja Weisgerber
Proposal for a regulationAnnex II – Number 4.1.2.1.4.1. – paragraph 1 – points a - c
Text proposed by the Commission Amendment
(a) If one specific gear ratio gives an acceleration in a tolerance band of � 5 % of the reference acceleration awot ref, not exceeding 3,0 m/s2, test with that gear ratio.
(b) If none of the gear ratios give the required acceleration, then choose a gear ratio i, with an acceleration higher and a gear ratio i + 1, with an acceleration lower than the reference acceleration. If the acceleration value in gear ratio i does not exceed 3,0 m/s2, use both gear ratios for the test. The weighting ratio in relation to
(a) If one specific gear ratio gives an acceleration in a tolerance band of � 5 % of the reference acceleration awot ref, not exceeding 2,0 m/s2, test with that gear ratio.
(b) If none of the gear ratios give the required acceleration, then choose a gear ratio i, with an acceleration higher and a gear ratio i + 1, with an acceleration lower than the reference acceleration. If the acceleration value in gear ratio i does not exceed 2,0 m/s2, use both gear ratios for the test. The weighting ratio in relation to
AM\905004EN.doc 15/67 PE491.113v02-00
EN
the reference acceleration awot ref is calculated by: k = (awot ref –awot (i+1)) / (awot (i) – awot (i+1))(c) if the acceleration value of gear ratio i exceeds 3.0 m/s2, the first gear ratio shall be used that gives an acceleration below 3.0 m/s2 unless gear ratio i + 1 provides acceleration less than aurban. In this case, two gears, i and i + 1 shall be used, including the gear i with acceleration exceeding 3.0 m/s2. The achieved acceleration is then used for the calculation of the part power factor kP instead of awot ref.
the reference acceleration awot ref is calculated by: k = (awot ref –awot (i+1)) / (awot (i) – awot (i+1)) (c) if the acceleration value of gear ratio i exceeds 2,0 m/s2, the first gear ratio shall be used that gives an acceleration below 2,0 m/s2 unless gear ratio i + 1 provides acceleration less than aurban. In this case, two gears, i and i + 1 shall be used, including the gear i with acceleration exceeding 2.0 m/s2. The achieved acceleration is then used for the calculation of the part power factor kP instead of awot ref.
Or. de
Justification
In order to simulate real urban traffic, the maximum acceleration should be set at 2.0 m/s2.
Amendment 116Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Patrizia Toia, Andres Perello Rodriguez
Proposal for a regulationAnnex II – point 4.1.2.2. – paragraph 1
Text proposed by the Commission Amendment
The path of the centreline of the vehicle shall follow line CC' as closely as possible throughout the entire test, from the approach to line AA' until the rear of the vehicle passes line BB'. The test shall be conducted without a trailer or semi-trailer. If a trailer is not readily separable from the towing vehicle, the trailer shall not be taken into consideration when assessing the crossing of line BB'. If the vehicle incorporates equipment such as a concrete mixer, a compressor, etc, this equipment shall not be in operation during the test. The test mass of the vehicle shall be
The path of the centreline of the vehicle shall follow line CC' as closely as possible throughout the entire test, from the approach to line AA' until the rear of the vehicle passes line BB'. The test shall be conducted without a trailer or semi-trailer. The test shall be conducted without a trailer or semi-trailer. If a trailer is not readily separable from the towing vehicle, the trailer shall not be taken into consideration when assessing the crossing of line BB'. If the vehicle incorporates equipment such as a concrete mixer this equipment shall not be in operation during
PE491.113v02-00 16/67 AM\905004EN.doc
EN
according to the table set out in point 3.2.1. the test. The test mass of the vehicle shall be according to the table set out in point 3.2.1.
Or. en
Justification
Compressors are used for air brakes and are therefore an intrinsic part of the vehicle. Noise from compressors should not therefore be excluded from noise measurements to ensure these are representative of real-world drive conditions, therefore including compressors.
Amendment 117Gilles Pargneaux
Proposal for a regulationAnnex III – paragraph 1 – introductory part
Text proposed by the Commission Amendment
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits and shall not exceed 90 dB(A) under any driving conditions, with a maximum speed of 130 km/h, in accordance with Annex VIII:
Or. fr
Justification
The regulation should ensure that excessively high noise emissions are ruled out during both hard and gentle acceleration. Relevant provisions should enable the competent authorities to take action that has an immediate impact on traffic.
Amendment 118Gilles Pargneaux
Proposal for a regulationAnnex III – column 2 – line 6
Text proposed by the Commission Amendment
no of seats < 9 no of seats ≤9; ≤ 125kW/tonne and
AM\905004EN.doc 17/67 PE491.113v02-00
EN
maximum 1900cc
Or. fr
Justification
The new standards proposed by the Commission can be achieved, but only over a longer period. Two extra years will be required before European vehicles emit a noise level similar to that of an electric vehicle.
Amendment 119Gilles Pargneaux
Proposal for a regulationAnnex III – column 5 – line 6
Text proposed by the Commission Amendment
68 70
Or. fr
Justification
The new standards proposed by the Commission can be achieved, but only over a longer period. Two extra years will be required before European vehicles emit a noise level similar to that of an electric vehicle.
Amendment 120Gilles Pargneaux
Proposal for a regulationAnnex III – column 6 – line 6
Text proposed by the Commission Amendment
69 71
Or. fr
Justification
The new standards proposed by the Commission can be achieved, but only over a longer period. Two extra years will be required before European vehicles emit a noise level similar to that of an electric vehicle.
PE491.113v02-00 18/67 AM\905004EN.doc
EN
Amendment 121Gilles Pargneaux
Proposal for a regulationAnnex III – limit values – column 2 – line 7
Text proposed by the Commission Amendment
no of seats < 9power to mass ratio > 150 kW/ton
no of seats ≤9;power to mass ratio > 125 kW/ton and minimum 1901 cc
Or. fr
Justification
The new standards proposed by the Commission can be achieved, but only over a longer period. Two extra years will be required before European vehicles emit a noise level similar to that of an electric vehicle.
Amendment 122Thomas Ulmer
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex III
Limit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:Vehicle category
Description of vehicle category
Limit values
expressed in dB(A)
[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
AM\905004EN.doc 19/67 PE491.113v02-00
EN
Phase 1 valid from
[2 years after publication]
Phase 2 valid from
[5 years after publication]
Phase 3 valid from
[7 years after publication]
General Off-road *
General Off-road *
General Off-road *
M Vehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
M1 no of seats < 9;
power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2 no of seats > 9; mass < 2 tons
72 72 70 70 70 70
M2 no of seats > 9; 2 tons < mass < 3.5 tons
73 74 71 72 71 72
M2 no of seats > 9; 3.5 tons < mass < 5 tons;
rated engine power < 150 kW
74 75 72 73 72 73
M2 no of seats > 9; 3.5 tons < mass < 5 tons;
rated engine power > 150 kW
76 78 74 76 74 76
M3 no of seats > 9; mass > 5 tons;
rated engine power < 150 kW
75 76 73 74 73 74
M3 no of seats > 9; mass > 5 tons;
rated engine power > 150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69
N1 2 tons < mass < 3.5 tons
72 73 70 71 70 71
N2 3.5 tons < mass <12 tons;
rated engine power < 75 kW
74 75 72 73 72 73
PE491.113v02-00 20/67 AM\905004EN.doc
EN
N2 3.5 tons < mass <12 tons;
75 < rated engine power < 150 kW
75 76 73 74 73 74
N2 3.5 tons < mass <12 tons;
rated engine power > 150 kW
77 79 75 77 75 77
N3 mass > 12 tons;
75 < rated engine power < 150 kW
77 78 75 76 75 76
N3 mass > 12 tons;
rated engine power > 150 kW
80 82 78 80 78 80
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
AM\905004EN.doc 21/67 PE491.113v02-00
EN
Amendment
Limit values, category and transitional provisions for ECE R51.03,new vehicle types
Stage 1 Stage 2 Stage 3
2 yearsafter entry into force of ECER51.03 Limit [dB(A)]
4 yearsafter stage 1
Limit [dB(A)]
6 yearsafter stage 1
Limit [dB(A)]
4 yearsafter stage 2
Limit [dB(A)]
6 years after stage 2
Limit [dB(A)]
PMR ≤ 120 kW/tM1 120 < PMR ≤ 160 kW/t PMR > 160 kW/t
727375
70-74
-71-
687073
---
GVW ≤ 2.5 toM2 2.5 to < GVW ≤ 3.5 to GVW > 3.5 to GVW
727475
7072-
--73
6971-
--71
P ≤ 180 kWM3 180 < P ≤ 250 kW P > 250 kW
767880
---
747878
---
737676
GVW ≤ 2.5 toN1 2.5 to < GVW ≤ 3.5 to
7274
7072
--
6871
--
PE491.113v02-00 22/67 AM\905004EN.doc
EN
P ≤ 150 kWN2 P > 150 kW
7778
--
7577
--
7275
P ≤ 250 kWN3 P > 250 kW
8182
--
7981
--
7779
Off-Road vehicles "G" for all categories +1 dB(A) for stage 1, wading depth 50cm, hill climbing ability 30% as additional requirement for M1GOff-Road vehicles "G" for all category N3, M3 +2 dB(A) for stage 2 and later, all other categories +1 dB(A) for stage 2 and later
Rounding and measurement uncertainty in accordance to R51.02
Or. en
AM\905004EN.doc 23/67 PE491.113v02-00
EN
Justification
Economic Commission for Europe - Regulation R51 (ECE-R51) should be amended with the implementation of a new test method and additional sound emission provisions (ASEP). The new test method should be introduced with new limit values. An environmental benefit should be reached with a 3 step approach of limit values. Transitional provisions shall reflect the vehicle manufacturers need to product redesign in accordance to usual product cycles.
Amendment 123Britta Reimers
Proposal for a regulationAnnexe III
Text proposed by the Commission
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category Description of vehicle category
Limit valuesexpressed in dB(A)[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from
[2 years after publication]
Phase 2 valid from
[5 years after publication]
Phase 3 valid from [7 years after publication]
General
Off-road *
General
Off-road *
General
Off-road *
M Vehicles used for the carriage of
PE491.113v02-00 24/67 AM\905004EN.doc
EN
passengers
M1 no of seats < 9 70 71** 68 69*
* 68 69**
M1no of seats < 9; power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2 no of seats > 9; mass < 2 tons 72 72 70 70 70 70
M2no of seats > 9; 2 tons < mass <3.5 tons 73 74 71 72 71 72
M2
no of seats > 9; 3.5 tons < mass <5 tons; rated engine power < 150 kW
74 75 72 73 72 73
M2
no of seats > 9; 3.5 tons < mass <5 tons; rated engine power > 150 kW
76 78 74 76 74 76
M3no of seats > 9; mass > 5 tons; rated engine power < 150 kW
75 76 73 74 73 74
M3no of seats > 9; mass > 5 tons; rated engine power > 150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69
N1 2 tons < mass < 3.5 tons 72 73 70 71 70 71
N23.5 tons < mass < 12 tons; rated engine power < 75 kW
74 75 72 73 72 73
N23.5 tons < mass < 12 tons; 75 < rated engine power < 150 kW
75 76 73 74 73 74
N23.5 tons < mass < 12 tons; rated engine power > 150 kW
77 79 75 77 75 77
N3mass > 12 tons; 75 < rated engine power < 150 kW
77 78 75 76 75 76
N3mass > 12 tons; rated engine power > 150 kW
80 82 78 80 78 80
AM\905004EN.doc 25/67 PE491.113v02-00
EN
*Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
**For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
Amendment by Parliament
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II and rounded to the nearest integer shall not exceed the following limits:
Vehicle Category
Description of vehicle category General limit values 1) for new vehicle types expressed in decibel (A)Phase 1 valid from2 years after entry into force
Phase 2 valid from6 years afterentry into force *
M1 Power-Mass-Ratio ≤ 120 kW/t 72 70
120 < Power-Mass-Ratio ≤ 150 kW/t 73 71
Power-Mass-Ratio > 150 kW/t 75 74
M2 Gross Vehicle Weight ≤ 2.5 to 72 71
2.5 to < Gross Vehicle Weight ≤ 3.5 to 74 73
N1 Gross Vehicle Weight ≤ 2.5 to; Cap < 660ccm; PMR(GVW)<35 kW/t
74 73
Gross Vehicle Weight ≤ 2.5 to 72 71
2.5 to < Gross Vehicle Weight ≤ 3.5 to 74 73
VehicleCategory
Description of vehicle category General limit values 1) for new vehicle types expressed in decibel(A)Phase 1 valid from3 years afterentry into force
Phase 2 valid from8 years afterentry into force
M2 Gross Vehicle Weight > 3.5 to ; Rated Power ≤ 135 kW
75 74
PE491.113v02-00 26/67 AM\905004EN.doc
EN
Gross Vehicle Weight > 3.5 to ; Rated Power > 135 kW
76 75
M3 2) Rated Power ≤ 135 kW 76 75
135 < Rated Power ≤ 250 kW 79 78M3 2) Rated Power > 250 kW 80 79
N2 Rated Power ≤ 135 kW 78 76Rated Power > 135 kW 79 78
N3 Rated Power ≤ 135 kW 79 78
135 < Rated Power ≤ 250 kW 81 80Rated Power > 250 kW 82 81
* For vehicles of category M1/N1 and M2 < 3.5 t, the transitional period for sale and entry into service of new vehicles is 2 years
1) The limit values shall be increased by +2dB for a vehicle of class M3 and N3 and +1 dB for any other vehicle, if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
2) The limit values shall be increased by +2dB for a vehicle of class M2 or M3, if the vehicle is equipped with a positive ignition engine with a rated engine speed greater than 3.500 rpm
Or. en
Justification
As the European Regulation on vehicle noise has a direct impact on the worldwide UN-ECE Regulation R51 it is important to consider limit values, vehicles classes and time lines which are compatible to the technologies in all markets that apply and want to apply to Regulation ECE R51. This will avoid a dis-harmonization of the markets and allow manufacturer an easy access to the global market.
Amendment 124Anja Weisgerber
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex IIILimit values
AM\905004EN.doc 27/67 PE491.113v02-00
EN
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category
Description of vehicle category
Limit valuesexpressed in dB(A)
[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from [2 years after publication]
Phase 2 valid from [5 years after publication]
Phase 3 valid from [7 years after publication]
General Off-road * General Off-road
* General Off-road *
MVehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
M1
no of seats < 9; power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2no of seats > 9; mass < 2 tons 72 72 70 70 70 70
M2
no of seats > 9; 2tons < mass < 3.5 tons
73 74 71 72 71 72
M2
no of seats > 9; 3.5tons < mass < 5 tons;rated engine power < 150 kW
74 75 72 73 72 73
M2
no of seats > 9; 3.5tons < mass < 5 tons; rated engine power > 150 kW
76 78 74 76 74 76
M3
no of seats > 9; mass > 5 tons; rated engine power < 150 kW
75 76 73 74 73 74
M3
no of seats > 9; mass > 5 tons; rated engine power > 150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of
PE491.113v02-00 28/67 AM\905004EN.doc
EN
goodsN1 mass < 2 tons 71 71 69 69 69 69
N12 tons < mass < 3.5 tons 72 73 70 71 70 71
N2
3.5 tons < mass <12 tons; rated engine power < 75 kW
74 75 72 73 72 73
N2
3.5 tons < mass <12 tons; 75 < rated engine power < 150 kW
75 76 73 74 73 74
N2
3.5 tons < mass <12 tons; rated engine power > 150 kW
77 79 75 77 75 77
N3
mass > 12 tons; 75 < rated engine power < 150 kW
77 78 75 76 75 76
N3
mass > 12 tons; rated engine power > 150 kW
80 82 78 80 78 80
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
Amendment
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle
category
Description of vehicle category
Limit valuesexpressed in dB(A)
[decibels(A)]
Limit values for Type-approval of
new vehicle types****
Limit values for Type-approval of
new vehicle types****
Limit values for Type-approval of
new vehicle types****
Limit values for
Type-approval of new vehicle
types*****
AM\905004EN.doc 29/67 PE491.113v02-00
EN
Phase 1 valid from [2 years after publication] ********
Phase 2 valid from [6 years after publication] ********
Phase 3 valid from [10 years after publication]
Phase 4 valid from [14 years after publication] ******
General Off-road * General Off-
road * General Off-road *
General ***
Vehicles used for the carriage of passengersand goods *******
M1
no of seats < 9;power to mass ratio < 120 kW/ton
72 73 ** 71 72** 71 72** 67
M1
no of seats < 9;120 kW/ton <power to mass ratio < 160 kW/ton
73 74 72 73 71 72 68
M1
no of seats < 9; power to mass ratio > 160 kW/ton
75 76 74 75 73 74 70
M2
no of seats > 9; mass < 2,5 tons; rated engine power < 75kW
71 72 69 70 69 70 68
M2
no of seats > 9;mass < 2,5 tons; rated engine power >75 kW
72 73 70 71 70 71 69
M2
no of seats > 9; 2,5 tons < mass < 3.5 tons
74 75 72 73 71 72 70
M2no of seats > 9; mass > 3.5 tons 76 77 73 74 72 73 71
N1 mass < 2,5 tons 72 73 71 72 71 72 69
N12,5 tons < mass < 3.5 tons 73 74 73 74 72 73 69
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of
new vehicle
Limit values for
Type-
PE491.113v02-00 30/67 AM\905004EN.doc
EN
types**** approval of new vehicle
types*****
Phase 1 valid from [3 years after publication]
Phase 2 valid from [8 years after publication]
Phase 3 valid from
[12 years after publication]
Phase 4 valid from [16 years
after publication] ******
General Off-road * General Off-
road *Genera
lOff-
road *General
***
M3
no of seats > 9; mass > 5 tons; rated engine power < 100 kW
74 75 73 74 72 73 71
M3
no of seats > 9; mass > 5 tons; 100 kW < rated engine power <180 kW
76 77 74 75 73 74 72
M3
no of seats > 9; mass > 5 tons; 180 < rated engine power < 250 kW
78 79 78 79 76 77 75
M3
No of seats > 9; mass > 5 tons; rated engine power > 250 kW
80 81 79 80 78 79 77
N2
3.5 tons < mass < 12 tons; rated engine power < 75 kW
76 77 75 76 74 75 71
N2
3.5 tons < mass < 12 tons; 75 < rated engine power < 150 kW
76 77 76 77 73 74 72
N2
3.5 tons < mass < 12 tons; 150 < rated engine power
78 79 77 78 77 78 74
N3mass > 12 tons; rated engine 76 77 75 76 75 76 72
AM\905004EN.doc 31/67 PE491.113v02-00
EN
power < 100 kW
N3
mass > 12 tons; 100 < rated engine power < 150 kW
79 80 78 79 77 78 75
N3
mass > 12 tons; 150 < rated engine power < 250 kW
81 82 80 81 79 80 77
N3
mass > 12 tons; rated engine power > 250 kW
82 83 81 82 80 81 79
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
*** For off-road vehicles the general limit values are increased by + 1 dB(A)**** Transitional period for first registration of new vehicles: 2 years after entry into force of
the applicable phase***** Transitional period for first registration of new vehicles: 3 years after entry into force of
the applicable phase****** The Commission shall carry out a detailed study to validate Phase 4 with respect to the
technical feasibility of the noise limits proposed, once Phase 3 is introduced. In case of a positive evaluation, Phase 4 shall be applied four years after publication of the Commission study.
******* M1 Special purpose vehicles:Wheelchair accessible vehicles (as defined in Paragraph 5.5 of Annex II to Directive 2007/46/EC) and armoured vehicles (as defined in Part A 5.2 Annex II to Directive 2007/46/EC), modification in the exhaust system pipe work is permitted without any further test provided all the original emission control devices including particulate filters (if any) are retained. If a new test is required, an extra 2dB(A) above the applicable limit shall be allowed.
******** For vehicles produced in small series according to section 1 of Part A of Annex XII to Directive 2007/46/EC the applicable date for phase 1 and phase 2 are delayed by two years.
Or. en
Justification
In order to increase the health benefits and to enhance legal certainty, long-term noise limit values should be established. The vehicle categories should be updated to the latest technical standards. These adaptations should make it possible to define ambitious noise limit values and to optimize the overall noise reduction. Further differentiating the vehicle categories enables us to establish more
PE491.113v02-00 32/67 AM\905004EN.doc
EN
ambitious noise limit values for vehicles with lower engine power and more realistic noise limit values for vehicles with higher engine power. The Regulation should reflect the differences in development and production of passenger cars and heavy duty vehicles. Accordingly, different phases for passenger cars and commercial vehicles shall be established.
Amendment 125Salvatore Tatarella, Miroslav Ouzký, Thomas Ulmer, Martin Callanan, Françoise GrossetêteProposal for a regulationAnnex III
Text proposed by the CommissionAnnex III
Limit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category
Description of vehicle category Limit values expressed in dB(A) [decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from [2 years after publication]
Phase 2 valid from [5 years after publication]
Phase 3 valid from
[7 years after publication]
GeneralOff-road *
General Off-road * General Off-road *
M Vehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
M1
no of seats < 9;power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2no of seats > 9; mass < 2 tons 72 72 70 70 70 70
M2 no of seats > 9; 2 tons < 73 74 71 72 71 72
AM\905004EN.doc 33/67 PE491.113v02-00
EN
mass < 3.5 tons
M2
no of seats > 9; 3.5 tons < mass < 5 tons; rated engine power < 150 kW
74 75 72 73 72 73
M2
no of seats > 9; 3.5 tons < mass < 5 tons; rated engine power >150 kW
76 78 74 76 74 76
M3
no of seats > 9; mass > 5 tons; rated engine power < 150 kW
75 76 73 74 73 74
M3
no of seats > 9; mass > 5 tons;
rated engine power >150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69N1 2 tons < mass < 3.5 tons 72 73 70 71 70 71
N2
3.5 tons < mass < 12 tons;
rated engine power < 75kW
74 75 72 73 72 73
N2
3.5 tons < mass < 12 tons;
75 < rated engine power < 150 kW
75 76 73 74 73 74
N2
3.5 tons < mass < 12 tons; rated engine power >150 kW
77 79 75 77 75 77
N3
mass > 12 tons; 75 < rated engine power < 150 kW
77 78 75 76 75 76
N3mass > 12 tons; rated engine power >
80 82 78 80 78 80
PE491.113v02-00 34/67 AM\905004EN.doc
EN
150 kW
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
AmendmentAnnex III
Limit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle Category
Description of vehicle category Limit values expressed in dB(A) [decibels (A)]
Limit values for Type-approvalof new vehicles types
Limit values for Type-approvalof new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from(1 year after publication)
Phase 2 valid from(6 years after publication)
Phase 3 valid from(8 years after publication)
General Off-road General Off-
road General Off-road
M Vehicles used for the carriage of passengers
M1 no of seats ≤ 9; ≤ 125 kW/ton 72 74*** 70 73*** 70 73***
M1no of seats ≤ 9; 125kW/ton < power to mass ratio ≤ 150kW/ton
73 75*** 71 74*** 71 74***
M1no of seats ≤ 9;power to mass ratio > 150kW/ton
75 74 74
M1 no of seats ≤ 4 including driver; Power to mass ratio >
77 / 76 / 76 /
AM\905004EN.doc 35/67 PE491.113v02-00
EN
200kw/ton; R point of the driver seat < 450 mm from ground
M2 no of seats > 9; mass ≤ 2.5tons 72 72 70 70 70 70
M2 no of seats > 9; 2.5 tons < mass ≤ 3,5 tons 74 75 72 73 72 73
M2no of seats > 9; 3,5 tons < mass ≤ 5 tons; rated engine power < 150kW
76 77 75 76 75 76
M2no of seats > 9; 3,5 tons < mass ≤ 5 tons; rated engine power ≥ 150kW
77 78 76 77 76 77
M3 no of seats > 9; mass > 5 tons; rated engine power ≤ 180kW 76 77 75 76 75 76
M3no of seats > 9; mass > 5 tons;180 kW < rated engine power ≤ 250kW
79 80 78 79 78 79
M3 no of seats > 9; mass > 5 tons; rated engine power > 250kW 80 81 79 80 79 80
N Vehicles used for the carriage of goods
N1 mass ≤ 2.5 tons 72 74 70 72 70 72
N1 2.5 tons < mass ≤ 3,5 tons 74 75 72 73 72 73
N2 3,5 tons < mass ≤ 12 tons;rated engine power < 150kW 77 78 76 77 76 77
N2 3,5 tons < mass ≤ 12 tons;rated engine power ≥150kW 78 79 77 78 77 78
N3 mass > 12 tons;rated engine power ≤180kW 79 80 78 79 78 79
N3mass > 12 tons;180 < rated engine power ≤250kW
81 82 80 81 80 81
N3 mass > 12 tons;rated engine power >250 kW 82 83 81 82 81 82
PE491.113v02-00 36/67 AM\905004EN.doc
EN
*** For M1 vehicles if the vehicle complies with the relevant definition for off-road vehicles according to article A.4 of Annex II of EU Directive 2006/46/EC and in addition have a wading depth exceeding 500 mm and a hill climbing capability of 35°.
Remark Limits for N3 only if "Normal Tyres" are allowed to be used for the test
Or. en
Justification
The Commission’s categorisation is mainly based on 70/157/EEC from 1970. It does not take into account the evolution of the vehicle market in the last decades and is not applicable for the future. A new better categorisation must take into account customer demands for an increased diversification of products. The lead time proposed by the Commission is too short and will lead to a premature termination of many vehicle types in production. For stage 1 the vehicle manufacturers will have to modify 23-89% of their fleet and for stage 2 between 75-100% of their remaining products. This will cause unpredictable losses. The amendment proposes a first step affecting already about 10-30% of the vehicle fleet, followed by a second step affecting another 20-40% depending on the proposed subcategories. This is technically feasible and affordable.
The limit values proposed for cars are based on the test requirements of 2 m/s2, the same as during the monitoring period. The Commission in its proposal has changed this test condition to 3 m/s2. The Parliament is encouraged to return to the original test condition. If this is not the case the limits in the table above shall be increased by +1 dB(A).
The limit values propose for heavy commercial vehicles are set to 82 dB(A), 81 dB(A) and 80 dB(A) in stage 1, effecting already 17-28% of all vehicles, based on the ACEA study with 159 analysed data files, corrected to the use of normal tyres. The lower limit values proposed by the Commission are based on the Venoliva study, where only 100 data files were analysed even if it was known that the manufacturers sent at least 159 data files. Already in 2010 ACEA aposed to this. The final Venoliva study from 2011stated that 179 data files have been in the data base but again only 100 data files were used for the analysis.
Amendment 126Holger Krahmer
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle Description of Limit values expressed in dB(A)
AM\905004EN.doc 37/67 PE491.113v02-00
EN
category vehicle category
Limit values for Type-approval of new
vehicle types
Limit values for Type-approval of new vehicle
types
Limit values for registration, sale
and entry into service of new
vehiclesPhase 1 valid from
[2 years after publication]
Phase 2 valid from [5 years after publication]
Phase 3 valid from [7 years after publication]
General Off-road * General Off-road * General
Off-road
*
MVehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
M1no of seats < 9;power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2no of seats > 9;mass < 2 tons 72 72 70 70 70 70
M2no of seats > 9; 2 tons < mass < 3.5 tons
73 74 71 72 71 72
M2
no of seats > 9; tons < mass < 5 tons;rated engine power < 150 kW
74 75 72 73 72 73
M2
no of seats > 9; tons < mass < 5 tons;rated engine power > 150 kW
76 78 74 76 74 76
M3
no of seats > 9;mass > 5 tons;rated engine power < 150 kW
75 76 73 74 73 74
M3
no of seats > 9;mass > 5 tons;rated engine power > 150 kW
77 79 75 77 75 77
NVehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69
N12 tons < mass < 3.5 tons 72 73 70 71 70 71
N2
tons < mass < 12 tons;rated engine power < 75 kW
74 75 72 73 72 73
N2
tons < mass < 12 tons;75 < rated engine power < 150 kW
75 76 73 74 73 74
N2
tons < mass < 12 tons;rated engine power > 150 kW
77 79 75 77 75 77
N3mass > 12 tons;75 < rated engine power < 150 kW
77 78 75 76 75 76
N3mass > 12 tons;rated engine power > 150 kW
80 82 78 80 78 80
PE491.113v02-00 38/67 AM\905004EN.doc
EN
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
Amendment
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II and rounded up to the next whole number shall not exceed the following limits:
General limit values 1) for new vehicle types, expressed in decibels (A)Vehicle category
Description of vehicle category Phase 1 valid from 2 years after publication
Phase 2 valid from 6 years after publication
Phase 3*** valid from 10 years after publication
power to mass ratio > 120 kW/ton 71 70 68M1
2)
120< PMR < 150 kW/t 72 71 69
PMR > 150 kW/t 74 73 72maximum permissible laden weight < 2,5 t; rated engine power < 75 kW/t
71 70 69
M2maximum permissible laden weight < 2,5 t; rated engine power < 75 kW/t
72 71 70
2,5 t < maximum permissible laden weight < 3,5 t;
74 73 71
N1 maximum permissible laden weight < 2,5 t;
72 71 69
2,5 t < maximum permissible laden weight < 3,5 t;
74 73 70
General limit values 1) for new vehicle types, expressed indecibels (A)
Vehicle category
Description of vehicle category
Phase 1 valid from 3 years after entry into force
Phase 2 valid from 8 years after entry into force
Phase 3*** valid from 12 years after entry into force**
M2
maximum permissible laden weight > 3,5 t;Rated engine power < 150 kW
76 74 72
AM\905004EN.doc 39/67 PE491.113v02-00
EN
maximum permissible laden weight > 3,5 t;Rated engine power > 150 kW
77 75 73
M3 Rated engine power < 100 kW
74 73 71
100 < Rated engine power< 150 kW
76 75 73
150 < Rated engine power< 250 kW
79 78 76
Rated engine power > 250 kW
80 79 78
Rated engine power < 75 kW
76 75 73
N2 75 < Rated engine power< 150 kW
77 76 74
Rated engine power > 150 kW
78 77 75
Rated engine power < 100 kW
76 75 73
N3 100 < Rated engine power< 150 kW
79 78 76
150 < Rated engine power< 250 kW
81 80 78
Rated engine power > 250 kW
82 81 80
* For vehicles in categories M1/N1 and M2 < 3.5 t the transitional period for purchase and entry into service of new vehicles shall be two years.
** For all vehicles the transitional period for purchase and entry into service of new vehicles shall be three years.
*** Immediately after the previous phase, the Commission shall conduct a study in order to assess the feasibility of this phase. If the assessment is positive, this phase shall apply for a period of four years from the publication of the relevant study.
1) The limit values shall be increased by +2dB for vehicles in categories M3 and N3 and by +1 dB for all other vehicles if the vehicle meets the relevant definition for off-road vehicles pursuant to Annex II, Section A, Number 4, of Directive 2007/46/EC.
2) The limit values shall be increased by +1dB for vehicles in category M1 if the vehicles are equipped with tyres from categories C1D or C1E in accordance with the definition in Annex II, Section A, of Regulation (EC) No 661/2009.
PE491.113v02-00 40/67 AM\905004EN.doc
EN
Or. de
Justification
In order to strike a balance between the industry’s need to retain its development cycles and legal security, and in order to achieve the requisite degree of health protection, the phases have been adjusted. Phase 3 in particular sets ambitious objectives. In addition, the vehicle categories have been brought into line with the latest technological standards. A more detailed breakdown of the vehicle categories makes it possible to set more realistic noise limit values. The periods are compatible with typical production cycles and are different for light and heavy commercial vehicles.
Amendment 127
Sabine Wils
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle categor
y
Description of vehicle category
Limit valuesexpressed in dB(A)
[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of
new vehicles
Phase 1 valid from
[2 years after publication]
Phase 2 valid from
[5 years after publication]
Phase 3 valid from
[7 years after publication]
General Off-road *
General Off-road *
General Off-road *
M Vehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
AM\905004EN.doc 41/67 PE491.113v02-00
EN
M1 no of seats < 9; power to mass ratio >
150 kW/ton
71 71 69 69 69 69
M2 no of seats > 9; mass < 2 tons
72 72 70 70 70 70
M2 no of seats > 9; 2 tons < mass < 3.5 tons
73 74 71 72 71 72
M2 no of seats > 9; 3.5 tons < mass < 5 tons;
rated engine power < 150 kW
74 75 72 73 72 73
M2 no of seats > 9; 3.5 tons < mass < 5 tons;
rated engine power >150 kW
76 78 74 76 74 76
M3 no of seats > 9; mass > 5 tons;
rated engine power < 150 kW
75 76 73 74 73 74
M3 no of seats > 9; mass > 5 tons;
rated engine power >150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69N1 2 tons < mass < 3.5
tons72 73 70 71 70 71
N2 3.5 tons < mass < 12 tons;
rated engine power < 75 kW
74 75 72 73 72 73
N2 3.5 tons < mass < 12 tons;
75 < rated engine power < 150 kW
75 76 73 74 73 74
N2 3.5 tons < mass < 12 tons;
rated engine power >
77 79 75 77 75 77
PE491.113v02-00 42/67 AM\905004EN.doc
EN
150 kW
N3 mass > 12 tons; 75 < rated engine power < 150 kW
77 78 75 76 75 76
N3 mass > 12 tons;
rated engine power >150 kW
80 82 78 80 78 80
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
Amendment by Parliament
Annex IIILimit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category
Description of vehicle category
Limit valuesexpressed in dB(A)
[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from
[1 years after publication]
Phase 2 valid from
[2 years after publication]
Phase 3 valid from
[4 years after publication]
Phase 4 valid from [6 years after publication]
Phase 5 valid from [8 years after publication]
General General General General General
M Vehicles used for the carriage
AM\905004EN.doc 43/67 PE491.113v02-00
EN
of passengers
M1**
no of seats < 9
power to mass ratio < 150 kW/ton
70 68 68 66 66
M1**
no of seats < 9
power to mass ratio > 150 kW/ton
71 69 69 67 67
M2
no of seats > 9
maximum mass < 2,5tons
72 70 70 68 68
M2
no of seats > 92.5 tons < maximum mass < 3,5 tons
73 71 71 69 69
M2
no of seats > 9
3.5 tons < maximum mass < 5 tons
74 72 72 70 70
M3
no of seats > 9
maximum mass > 5 tons
rated engine power < 250 kW
75 73 73 71 71
M3
no of seats > 9
maximum mass > 5 tons
rated engine power > 250 kW
77 75 75 73 73
NVehicles used for the carriage of goods
N1** maximum mass < 2.5
71 69 69 67 67
PE491.113v02-00 44/67 AM\905004EN.doc
EN
tons
N1**
2.5 tons < maximum mass < 3.5 tons
72 70 70 68 68
N2
3.5 tons < maximum mass < 12 tons
rated engine power < 150 kW
75 73 73 71 71
N2
3.5 tons < mass < 12 tons rated engine power > 150 kW
77 75 75 73 73
N3
maximum mass > 12 tons
rated engine power < 250 kW
76 74 74 72 72
N3***
maximum mass > 12 tons
rated engine power > 250kW
78 76 76 74 74
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 and N1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
*** All limit values for N3 vehicles have been lowered by 1dB (A) to take account of the change of instructions for the tyres in the test method B
**** For off-road vehicles all limit values are 1dB (A) lower
Or. en
AM\905004EN.doc 45/67 PE491.113v02-00
EN
Amendment 128Toine Manders, Satu Hassi
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex III
Vehicle category
Description of vehicle category
Limit valuesexpressed in dB(A)[decibels(A)]Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from [2 years after publication]
Phase 2 valid from [5 years after publication]
Phase 3 valid from [7 years after publication]
General Off-road *
General Off-road *
General Off-road *
M Vehicles used for the carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**M1 no of seats < 9;
power to mass ratio > 150 kW/ton
71 71 69 69 69 69
M2 no of seats > 9; mass < 2 tons
72 72 70 70 70 70
M2 no of seats > 9; 2tons < mass < 3.5tons
73 74 71 72 71 72
M2 no of seats > 9; 3.5 tons < mass < 5 tons; rated engine power < 150 kW
74 75 72 73 72 73
M2 no of seats > 9; 3.5tons < mass < 5 tons; rated engine power > 150 kW
76 78 74 76 74 76
M3 no of seats > 9; mass > 5 tons;
75 76 73 74 73 74
PE491.113v02-00 46/67 AM\905004EN.doc
EN
rated engine power < 150 kW
M3 no of seats > 9; mass > 5 tons; rated engine power > 150 kW
77 79 75 77 75 77
N Vehicles used for the carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69N1 2 tons < mass < 3.5
tons72 73 70 71 70 71
N2 3.5 tons < mass <12 tons; rated engine power < 75 kW
74 75 72 73 72 73
N2 3.5 tons < mass <12 tons; 75 < rated engine power < 150 kW
75 76 73 74 73 74
N2 3.5 tons < mass <12 tons; rated engine power > 150 kW
77 79 75 77 75 77
N3 mass > 12 tons; 75 < rated engine power < 150 kW
77 78 75 76 75 76
N3 mass > 12 tons; rated engine power > 150 kW
80 82 78 80 78 80
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
Vehicle category
Description of vehicle category
Limit values
expressed in dB(A)
Amendments by Parliament
AM\905004EN.doc 47/67 PE491.113v02-00
EN
[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Phase 1 valid from [2 years after publication]
Phase 2 valid from [5 years after publication]
M Vehicles used for the carriage of passengers
M1 no of seats < 9 68 67
M1
no of seats < 9; power to mass ratio > 150 kW/ton
71 69
M2no of seats > 9; mass < 3.5tons 73 71
M2
no of seats > 9; 3.5 tons < mass < 5 tons;
rated engine power < 150 kW
74 72
M2
no of seats > 9; 3.5 tons < mass < 5 tons; rated engine power > 150 kW
76 74
M3
no of seats > 9; mass > 5 tons; rated engine power < 150 kW
75 73
M3
no of seats > 9; mass > 5 tons;
rated engine power > 150 kW
77 75
N Vehicles used for the carriage of goods
N1 mass < 2,5 tons 68 67
N1 2,5 tons < mass < 3.5 tons 70 68
PE491.113v02-00 48/67 AM\905004EN.doc
EN
N2
3.5 tons < mass < 12 tons; rated engine power < 150kW
75 73
N2
3.5 tons < mass < 12 tons;
rated engine power > 150 kW
77 75
N3
mass > 12 tons; rated engine power < 150 kW
77 75
N3
mass > 12 tons;
rated engine power > 150 kW
79 77
* For all vehicles the limit values shall be increased by 1 dB(A) if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For all vehicle categories the transitional period for sale and entry into service of new vehicles is 2 years.
Or. en
Justification
Noise is a severe damage of health. Studies show that source abatement is cost efficient and silent vehicles on silent tyres are most cost effective. This approach is also based on the “polluter pays principle” which is fair and balanced. This proposal is ambitious to limit noise damage, but also realistic to enable the industry to adapt. As obliged by the Safety Regulation (2009/661) more silent tyres are demanded, also for new vehicles. This means new vehicles will be more silent, also in the approval test. Low noise technology for cars is already in the market. 63% of the cars fulfil the first phase of the Commission proposal. With the tyre noise demands coming into force by November 2012, this will even be more: 95%. This means that the first Commission phase is already dealt with and can be skipped. The Commission second phase is adequate and even a third step is feasible. Already more than 20% of the vehicles is substantial more silent than the second requirement of the Commission. Cars which fulfil the new second step are already on the market now. So the technology is available. For trucks, limit values have to be corrected for a change in the measurement method. In Geneva, the method has been changed (silent tyres allowed instead of noisy traction tyres). Trucks also will become more silent in type approval measurements. The first step is fulfilled.Noisy traction tyres have been replaced by more silent steering tyres, giving a 1 a 2 dB lower measured result. This is confirmed by the limit proposal from Japan in UNECE/GRB (ECE-TRANS-WP29-GRB-55-inf01e and inf10e). The feasibility of the final step of 77 dB(A) from the Japanese
AM\905004EN.doc 49/67 PE491.113v02-00
EN
proposal is confirmed by a recent study, where the encapsulation technology of 1990 was combined with the silent engines of 2012, giving a noise emission of 77 dB(A).
The limit values of M1, N1 and N3 vehicles have been lowered compared to the Commission's proposal. With regard to M1 and N1 vehicles, because more silent tyres will become available as from 1 November 2012 due to EC directive 2009/661. For N3, vehicles because the measurement method has been changed, giving lower test results (noisy traction tyres have been replaced by more silent steering tyres).
The vehicles categories, the off road allowance and the transitional provisions have been rationalized and simplified.
In order to ensure the appropriate balance between the need to maintain industrial development cycles and legal certainty and to achieve the necessary public health benefits, four phases have been established. Phases 3 and 4 in particular set ambitious targets. The vehicle categories have also been updated to the latest technical standards. The further differentiation of these vehicle categories enables more realistic noise limit values. The time periods are compatible to typical production cycles and are different for light duty and heavy duty vehicles.
Amendment 129Judith A. Merkies, Nessa Childers, Minodora Cliveta
Proposal for a regulationAnnex III
Text proposed by the Commission
Annex III
Limit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category
Description of vehicle
category
Limit values
expressed in dB(A)[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of
new vehicles
Phase 1 valid from [2 years after publication]
Phase 2 valid from [5 years after publication]
Phase 3 valid from [7 years after publication]
PE491.113v02-00 50/67 AM\905004EN.doc
EN
General Off-road *
General Off-road *
General Off-road *
M Vehicles used for the
carriage of passengers
M1 no of seats < 9 70 71** 68 69** 68 69**
M1 no of seats <9;
power to mass ratio > 150
kW/ton
71 71 69 69 69 69
M2 no of seats > 9; mass < 2
tons
72 72 70 70 70 70
M2 no of seats > 9; 2 tons < mass < 3.5
tons
73 74 71 72 71 72
M2 no of seats > 9; 3.5 tons <
mass < 5 tons; rated engine power < 150
kW
74 75 72 73 72 73
M2 no of seats > 9; 3.5 tons <
mass < 5 tons; rated engine power > 150
kW
76 78 74 76 74 76
M3 no of seats > 9; mass > 5
tons;rated engine power < 150
kW
75 76 73 74 73 74
M3 no of seats > 9; mass > 5
tons; rated engine
77 79 75 77 75 77
AM\905004EN.doc 51/67 PE491.113v02-00
EN
power > 150 kW
N Vehicles used for the
carriage of goods
N1 mass < 2 tons 71 71 69 69 69 69N1 2 tons < mass
< 3.5 tons72 73 70 71 70 71
N2 3.5 tons < mass < 12
tons; rated engine power < 75
kW
74 75 72 73 72 73
N2 3.5 tons < mass < 12
tons; 75 < rated
engine power < 150 kW
75 76 73 74 73 74
N2 3.5 tons < mass < 12
tons; rated engine power > 150
kW
77 79 75 77 75 77
N3 mass > 12 tons;
75 < rated engine power
< 150 kW
77 78 75 76 75 76
N3 mass > 12 tons;
rated engine power > 150
kW
80 82 78 80 78 80
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
PE491.113v02-00 52/67 AM\905004EN.doc
EN
** For M1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
AM\905004EN.doc 53/67 PE491.113v02-00
EN
Amendments by Parliament
Annex III
Limit values
The sound level measured in accordance with the provisions of Annex II shall not exceed the following limits:
Vehicle category
Description of vehicle category
Limit values
expressed in dB(A)[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from [1 years after publication]
Phase 2 valid from [3 years after publication]
Phase 3 valid from
[5 years after publication]
Phase 4 valid from [8 years after publication]
Phase 5 valid from [10 years after publication]
General Off-road * General Off-road
*General
Off-road * General Off-
road * General Off-road *
M Vehicles used for the carriage of passengers
M1no of seats < 9
power to mass ratio < 150 kW/ton70 71** 68 69** 68 69** 66 67 66 67
PE491.113v02-00 54/67 AM\905004EN.doc
EN
M1no of seats < 9
power to mass ratio > 150 kW/ton71 71** 69 69** 69 69** 67 67** 67 67**
M2no of seats > 9
maximum mass < 2,5 tons72 72 70 71 70 71 68 69 68 69
M2
no of seats > 92.5 tons < maximum mass < 3,5 tons
73 74 71 72 71 72 69 70 69 70
M2no of seats > 9
3.5 tons < maximum mass < 5 tons 74 75 72 73 72 73 70 71 70 71
M3
no of seats > 9
maximum mass > 5 tonsrated engine power < 250 kW
75 76 73 74 73 74 71 72 71 72
M3
no of seats > 9maximum mass > 5 tons
rated engine power > 250 kW77 79 75 77 75 77 73 75 73 75
AM\905004EN.doc 55/67 PE491.113v02-00
EN
Vehicle category
Description of vehicle categoryLimit valuesexpressed in dB(A)[decibels(A)]
Limit values for Type-approval of new vehicle types
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Limit values for Type-approval of new vehicle types
Limit values for registration, sale and entry into service of new vehicles
Phase 1 valid from [1 years after publication]
Phase 2 valid from [3 years after publication]
Phase 3 valid from [5 years after publication]
Phase 4 valid from [8 years after publication]
Phase 5 valid from [10 years after publication]
General Off-road *
General
Off-road *
General
Off-road *
General
Off-road * General Off-road
*
N Vehicles used for the carriage of goods
N1 maximum mass < 2.5 tons 71 72** 69 70** 69 70** 67 68** 67 68**
N12.5 tons < maximum mass < 3.5 tons 72 73** 70 71** 70 71** 68 69** 68 69**
N2
3.5 tons < maximum mass < 12 tons
rated engine power < 150 kW75 76 73 74 73 74 71 72 71 72
N2 3.5 tons < mass < 12 tons 77 79 75 77 75 77 73 75 73 75
PE491.113v02-00 56/67 AM\905004EN.doc
EN
rated engine power > 150 kW
N3maximum mass > 12 tonsrated engine power < 250 kW
77 78 75 76 75 76 73 74 73 74
N3***maximum mass > 12 tons
rated engine power > 250 kW79 81 77 79 77 79 75 77 75 77
* Increased limit values shall only be valid if the vehicle complies with the relevant definition for off-road vehicles set out in point 4 of Section A of Annex II to EU Directive 2007/46/EC.
** For M1 and N1 vehicles the increased limit values for off-road vehicles are only valid if the maximum authorised mass > 2 tonnes.
*** All limit values for N3 vehicles have been lowered by 1dB (A) to take account of the change of instructions for the tyres in the test method B
Or. en
AM\905004EN.doc 57/67 PE491.113v02-00
EN
Amendment 130Karl-Heinz Florenz
Proposal for a regulationAnnex III, remark below table (new)
Text proposed by the Commission Amendment
And shall not exceed 90 dB(A) in any driving conditions, below a maximum speed of130 km/h, in accordance with Anne VIII.
Or. de
Justification
The aim of the regulation is to ensure that extreme vehicle noise emissions are ruled out.
Amendment 131
Judith A. Merkies, Nessa Childers, Minodora Cliveta, Kathleen van Brempt, Andres Perello Rodriguez
Proposal for a regulationAnnex III – point 1 – below table (new)
Text proposed by the Commission Amendment
And shall not exceed 90 dB(A) in any driving conditions, below a maximum speed of130 km/h, in accordance with Anne VIII.
Or. en
Justification
It is appropriate that the Regulation ensures extreme noise emissions under wide open or partial throttle conditions are precluded. Provisions should allow for straightforward enforcement in traffic by relevant authorities.
PE491.113v02-00 58/67 AM\905004EN.doc
EN
Amendment 132
Sabine Wils
Proposal for a regulationAnnex III – point 1 – below table (new)
Text proposed by the Commission Amendment
And shall not exceed 87 dB(A) in any driving conditions, below a maximum speed of 130 km/h, in accordance with Anne VIII.
Or. en
Justification
It is appropriate that the Regulation ensures extreme noise emissions under wide open or partial throttle conditions are precluded. Provisions should allow for straightforward enforcement in traffic by relevant authorities.
Amendment 133Françoise Grossetête
Proposal for a regulationAnnex VII – point 3.2.2. – paragraph 2 – introductory part –
Text proposed by the Commission Amendment
In addition to the requirements set out under points 1 to 3.2.2, the following requirements shall be fulfilled:
In addition to the requirements set out under points 1 to 3.2.1.4, the following recommendations are given, to be taken as requirements for newly-built test tracks:
Or. en
Justification
The Commission proposal provides a change in the specification for the construction of the test site. What is up to now a recommendation would become mandatory. With that change, any test track currently used in Europe would be subject for re-certifications as if newly built.
Amendment 134Salvatore Tatarella, Miroslav Ouzký
AM\905004EN.doc 59/67 PE491.113v02-00
EN
Proposal for a regulationAnnex VII – point 3.2.2 – paragraph 2 – introductory part
Text proposed by the Commission Amendment
In addition to the requirements set out under points 1 to 3.2.2, the followingrequirements shall be fulfilled:
In addition to the requirements set out under points 1 to 3.2.1.4, the following recommendations are given:
Or. en
Justification
The Commission proposal provides a change in the specification for the construction of the test site. What is up to now a recommendation for road builders to have a guideline how to make a test track, will become mandatory. This change was done without technical consultation and there is no explanation provided by the Commission about the background for that change. With that change, actually any test track that is used in Europe will be subject for re-certifications as if newly built. Nobody knows the impact of the change of the specifications and could force re-building of many test tracks. As already told there is a new ISO Standard available, which is assumed to substitute the actual test track definitions within a couple of year, it is recommended to stay with the actual specifications.
Amendment 135Salvatore Tatarella, Miroslav Ouzký
Proposal for a regulationAnnex VII – point 3.2.2 – paragraph 2 – introductory part
Text proposed by the Commission Amendment
In addition to the requirements set out under points 1 to 3.2.2, the following requirements shall be fulfilled:
In addition to the requirements set out under points 1 to 3.2.2, the following requirements of ISO 10844:2011 shall be fulfilled or a reference should be made to ISO 10844:1994 for a transitional period of 5 years:
Or. en
Justification
This requirement should be consistent with both Paragraph 1 of Annex VII of this Regulation and the work done by UNECE. The requirements set in this Paragraph from point (a) to (g) are taken from the ISO standard 10844:2011. However, this standard is not yet included in any UNECE
PE491.113v02-00 60/67 AM\905004EN.doc
EN
Regulation. It is therefore necessary to also make reference to the previous version of the ISO standard 10844:1994 for a transitional period of five years to both allow the UNECE to change its own regulations and for the testing facilities to introduce the changes demanded by the 2011 version of this standard.
Amendment 136Salvatore Tatarella, Miroslav Ouzký
Proposal for a regulationAnnex VII – point 2 – footnote 1
Text proposed by the Commission Amendment
1/ ISO10844:1994. 1/For the first five years after the entry into force of this Regulation, manufacturers may either use test tracks certified according to ISO 10844:1994 or ISO 10844:2011. After that date manufacturers shall use test tracks complying with ISO 10844:2011 only.
Or. en
Justification
ISO10844:1994 has been updated in March 2011 into the new ISO standard ISO10844:2011. However the new text has not yet been introduced in all UNECE regulations regarding vehicle and tyre testing facilities. For this reason, it is important to have a transition period between the two standards to give the opportunity to manufacturers to rebuild any track where needed and for UNECE to introduce the reference to the new standard in its own regulations.
Amendment 137
Judith A. Merkies, Nessa Childers, Minodora Cliveta, Andres Perello Rodriguez
Proposal for a regulationAnnex VII – point 4.3.
Text proposed by the Commission Amendment
4.3. For the purpose of this standard, texture depth measurements shall be made on at least 10 positions evenly spaced along the wheel tracks of the test strip and
4.3. For the purpose of this standard, texture depth measurements shall be made on at least 10 positions evenly spaced along the wheel tracks of the test strip and
AM\905004EN.doc 61/67 PE491.113v02-00
EN
the average value taken to compare with the specified minimum texture depth. See ISO 10844:1994 for the description of the procedure.
the average value taken to compare with the specified minimum texture depth. See ISO10844:2011 for the description of the procedure.
Or. en
Justification
Regulation should be in line with the current ISO standards.
Amendment 138Salvatore Tatarella, Miroslav Ouzký, Martin Callanan
Proposal for a regulationAnnex VIII – point 2.3. – line 4 'Vehicle acceleration'
Text proposed by the Commission Amendment
Vehicle acceleration awot ASEP: awot ≤ 5,0 m/s2
Vehicle acceleration awot ASEP: awot ≤ 4,0 m/s2
Or. en
Justification
The acceleration rate required in the ASEP test as set out in the Commission proposal is unrepresentative of urban driving conditions. Also, the test becomes increasingly complex and difficult to repeat consistently at higher accelerations. The data set used for the ASEP does not derive from Method B data. In fact, method B and ASEP are not related therefore change to Method B does not need to be replicated in the ASEP test. Furthermore, a full impact assessment has not been carried out to account for the change from 4.0 to 5.0 m/s2.
Amendment 139Salvatore Tatarella, Miroslav Ouzký, Martin Callanan
Proposal for a regulationAnnex VIII – paragraph 2.4. –paragraph 3 (new)
Text proposed by the Commission Amendment
In order for the ASEP test to be representative and repeatable (to the Type
PE491.113v02-00 62/67 AM\905004EN.doc
EN
Approval Authority), the vehicles shall be tested using production gearbox calibration.
Or. en
Justification
Using the production gearbox calibration is necessary for the following reasons: As the gearbox has to be operated outside its ‘normal’ parameters, a calibration is required to ‘hold’ selected gears during the ASEP test; With regard to the above, a special calibration is not available for production cars. Conformity of Production is therefore not achievable; Non Linear acceleration: holding a high numeric gear and applying full power from low RPM (Revolution per Minute) can cause the engine RPM to ‘flair’. Flaring is caused by the torque converter slipping at low engine RPM.
Amendment 140Karl-Heinz Florenz
Proposal for a regulationAnnex VIII – point 4 – paragraph 3
Text proposed by the Commission Amendment
If the measured noise level at a point exceeds the limit, two additional measurements at the same point shall be carried out to verify the measurement uncertainty. The vehicle is still in compliance with ASEP, if the average of the three valid measurements at this specific point fulfils the specification.
If the measured noise level at a point exceeds the limit, two additional measurements at the same point shall be carried out to verify the measurement uncertainty. The vehicle is still in compliance with ASEP, if the average of the three valid measurements at this specific point fulfils the specification. The noise level may not exceed 90 dB(A) in any driving situation.
Or. de
Justification
The regulation should ensure that extreme noise emissions from motor vehicles are ruled out.
AM\905004EN.doc 63/67 PE491.113v02-00
EN
Amendment 141Holger Krahmer
Proposal for a regulationAnnex IX
Text proposed by the Commission
Annex IX
Measures ensuring the audibility of hybrid and electric vehicles
This Annex addresses Acoustic Vehicle Alerting System (AVAS) for hybrid electric and pure electric road transport vehicles (HEV and EV).
A Acoustic Vehicle Alerting System
1. Definition
Acoustic Vehicle Alerting System (AVAS) is a sound generating device designed to inform pedestrians and vulnerable road users.
2. System performance
If AVAS is installed on a vehicle, it shall fulfil the requirements referred to below.
3. Operation conditions
(a) Sound generation method
The AVAS shall automatically generate a sound in the minimum range of vehicle speed from start up to approximately 20 km/h and during reversing if applicable
for that vehicle category. Where the vehicle is equipped with an internal combustion engine that is in operation within the vehicle speed range defined
above, the AVAS may not need to generate a sound.For vehicles having a reversing sound warning device, it is not necessary for the
AVAS to generate a sound during backup.
(b) Pause switch
The AVAS may have a switch to stop its operation temporarily ("pause switch").If a pause switch is introduced, however, the vehicle should also be equipped with a device for indicating the pause state of the vehicle-approach informing device
to the driver in the driver's seat.The AVAS should remain capable of re-operating after stopped by a pause
switch.If fitted in the vehicle, a pause switch should be located in such a position that
the driver will find and manipulate it with ease.
(c) Attenuation
PE491.113v02-00 64/67 AM\905004EN.doc
EN
The AVAS sound level may be attenuated during periods of vehicle operation.
4. Sound type and volume
(a) The sound to be generated by the AVAS should be a continuous sound that provides information to the pedestrians and vulnerable road users of a vehicle in operation. However, the following and similar types of sounds are not acceptable:
(i) Siren, horn, chime, bell and emergency vehicle sounds (ii) Alarm sounds e.g. fire, theft, smoke alarms(iii) Intermittent sound
The following and similar types of sounds should be avoided:(iv) Melodious sounds, animal and insect sounds
(v) Sounds that confuse the identification of a vehicle and/or its operation (e.g. acceleration, deceleration etc.)
(b) The sound to be generated by the AVAS should be easily indicative of vehicle behaviour, for example, through the automatic variation of sound level or
characteristics in synchronization with vehicle speed.
(c) The sound level to be generated by the AVAS should not exceed the approximate sound level of a similar vehicle of the same category equipped with an internal combustion engine and operating under the same conditions.Environmental consideration:The development of the AVAS shall give consideration to the overall community
noise impact.
Amendment
deletedOr. de
JustificationWhere minimum requirements are concerned, impact assessments must be carried out and further findings obtained before rules can be adopted. Compliance with those rules must then be mandatory, not voluntary. What is more, they relate to transport safety and are out of place in environmental legislation.
Amendment 142Karl-Heinz Florenz
Proposal for a regulationAnnex IX – point 4
AM\905004EN.doc 65/67 PE491.113v02-00
EN
Text proposed by the CommissionAnnex IX
4. Sound type and volume(a) The sound to be generated by the AVAS should be a continuous sound that provides
information to the pedestrians and vulnerable road users of a vehicle in operation.However, the following and similar types of sounds are not acceptable:
(i) Siren, horn, chime, bell and emergency vehicle sounds(ii) Alarm sounds e.g. fire, theft, smoke alarms(iii) Intermittent sound
The following and similar types of sounds should be avoided:(iv) Melodious sounds, animal and insect sounds(v) Sounds that confuse the identification of a vehicle and/or its operation
(e.g. acceleration, deceleration etc.)(b) The sound to be generated by the AVAS should be easily indicative of vehicle
behaviour, for example, through the automatic variation of sound level or characteristics in synchronization with vehicle speed.
(c) The sound level to be generated by the AVAS should not exceed the approximate sound level of a similar vehicle of the same category equipped with an internal combustion engine and operating under the same conditions.Environmental consideration:The development of the AVAS shall give consideration to the overall community noise impact.
PE491.113v02-00 66/67 AM\905004EN.doc
EN
Amendment
Or. de
Amendment 143Salvatore Tatarella, Miroslav Ouzký, Francoise Grossetête
Proposal for a regulationAnnex X – point 5.2.1.1.
Text proposed by the Commission Amendment
5.2.1.1 The noise test of the silencing system and the replacement silencing system has to be executed with the same "normal" tyres as defined in paragraph 2.8. of UNECE Regulation No 117 (OJ L231, 29.8.2008 p. 19). The tests are not allowed to be done with "special use" tyres or
5.2.1.1 The noise test of the silencing system and the replacement silencing system has to be executed with the "normal" tyres as defined in paragraph 2.8 UNECE Regulation No. 117. The tests are not allowed to be done with "traction tyres", "special use" tyres or "snow" tyres
Annex IX
4. Sound type and volume(a) The sound to be generated by the AVAS should be a continuous sound that provides
information to the pedestrians and vulnerable road users of a vehicle in operation.However, the following and similar types of sounds are not acceptable:
(i) Siren, horn, chime, bell and emergency vehicle sounds(ii) Alarm sounds e.g. fire, theft, smoke alarms(iii) Intermittent sound
The following and similar types of sounds should be avoided:(iv) Melodious sounds, animal and insect sounds(v) Sounds that confuse the identification of a vehicle and/or its operation
(e.g. acceleration, deceleration etc.)(b) The sound to be generated by the AVAS must be easily indicative of vehicle
behaviour and direction of travel, for example, through the automatic variation of sound level or characteristics in synchronization with vehicle speed.
(c) The sound level to be generated by the AVAS may not exceed the approximate sound level of a similar vehicle of the same category equipped with an internal combustion engine and operating under the same conditions.Environmental consideration:The development of the AVAS shall give consideration to the overall community noise impact.
AM\905004EN.doc 67/67 PE491.113v02-00
EN
"snow" tyres as defined in paragraphs 2.9.and 2.10. of UNECE Regulation No 117. Such tyres could increase the noise level of the vehicle or would have a masking effect on the noise reduction performance comparison. The tyres may be of used condition but shall satisfy legal requirements for in-traffic use.
as defined in paragraphs 2.10, 2.11 and 2.12 of UNECE Regulation No 117.
Or. en
Justification
As for Annex II - paragraph 3 - point 3.2.2 of this regulation, the reference to the outdated version of UNECE 117 should be deleted. Furthermore, traction tyres should be added to this second paragraph to make it consistent with footnote 2 in Annex II - paragraph 3 - point 3.2.2 of this regulation. The paragraph numbers containing the definitions of traction tyres, special use tyres and snow tyres in UNECE Regulation No 117 should be updated accordingly.