Upload
api-26013089
View
1.106
Download
1
Embed Size (px)
Citation preview
Icom’s flagship model
+40dBm 3rd order interceptpoint (in the HF bands)
Two completely independent receiver circuits
Four 32-bit DSP units and 24-bit AD/DA converters
Digital IF filter
200W output power and highlystable transmitter
+40dBm IP3 (3rd order Intercept Point)
Icom’s considerable analog RF circuitexperience combined with cutting-edgedigital technology results in an astonishing110dB receiver dynamic range and a+40dBm IP3 in the HF bands. A first inHam radio! To achieve this superior receiv-er performance, Icom’s engineering teamcompletely re-engineered the whole ana-log circuit and matched it to the DSP units.
Two completely independent receiver circuitsThe dual receiver allows you to receive twodifferent bands simultaneously in differentmodes, with each receiver not causing anyadverse affect to the other one.
Quad processingThe IC-7800 incorporates four independent,32-bit DSP units and 24-bit AD/DA convert-ers. By having four independent DSP units,the radio will respond to operator changesin an instant, as each DSP unit has a dedi-cated function. While there is one for eachreceiver, there is a DSP unit for transmit aswell as a DSP unit for the Spectrum Scope.
Digital IF filterIcom’s digital IF filters give you performancethat is not possible with crystal or mechani-cal filters. This allows the operator to adjustfilter shaping (sharp or soft), filter bandwidth,and center frequency characteristics, with-out missing the action. Multiple filter memo-ries store the last used filter settings byusing operation mode.
Ultra high stability OCXO unitThe IC-7800 uses the OCXO (Oven ControlCrystal Oscillator) unit which is stable to with-in ±0.05ppm at 0˚C to 50˚C. This specifica-tion means that even on the 50MHz band,frequency error is less than 2.5Hz!
200W output powerThe newly designed push-pull poweramplifiers using power MOS-FETs work on48V DC. They provide a powerful 200Woutput power at full duty cycle. An effectivecooling system maintains internal tempera-tures within asafe rangeand preventsthermal run-away.
Real time spectrum scopeDue to the DSP unit for the scope, the IC-7800’s spectrum scope provides excellentsensitivity, with 80dB of dynamic range.While the scope rivals many of today’scommercial test sets, there are 7 steps,ranging from ±2.5kHz to ±250kHz. This isup to 500kHz of spectrum!
7-inch wide color TFT LCDAn active matrix 7-inch (800×400 pixel) TFTcolor display was selected for the IC-7800. This large display shows main, sub-bandfrequencies, including various settings, andoperating conditions, as well as the spec-trum scope, S-meter, and RTTY/PSK31decoded messages. The “virtual” S-metershows high quality, analog-looking needleswings that are smooth and accurate.
Other outstanding features• DSP controlled CW keying waveformshaping • Multi-function electronic keyerwith adjustable keying speed, dot-dash ratioand paddle polarity • AGC volume knob forfine tuning of the AGC time constant • 3-step manual notch filter • Microphoneequalizer and adjustable transmit band-width • Built-in RTTY and PSK31 modulatorand demodulator • Pre-amplifier and mixercircuit dedicated for 50MHz band • Highquality digital voice memory • 64MB CFmemory card for storing various personalsettings • Digital twin PBT eliminates inter-ference from adjacent signals • 16-stepnoise reduction • 4 antenna connectors withautomatic antenna selector • Triple bandstacking register • Automatic antenna tuner• Twin peak audio filter for RTTY operation• Message memory for CW, RTTY andPSK31 operations • 101 memory channels
Filter preset screen.
PA Unit and heat sink
Dynamic range characteristics (in 14MHz band)
Au
dio
ou
tpu
t level
Input level at the antenna connector [dBm]
IP3 (3rd order Intercept Point)
3dB
[dB]
50
40
30
20
10
0
Sensitivity3rd order Intermodulation
Noise floor level
Dynamic range
110dB
+40dBm
Two roofing filters
BPF unit
DIGI-SEL unit
Example of spectrumscope centered on thereceiving frequency.
Example of fixedspectrum scoperange.
AGC loop managementThe digital IF filter, manual notch filter etc.are adopted in the AGC loop, and controlledby the DSP. This system removes blockingby extremely strong adjacent signals in outof filter passbands, even very weak signalsbetween crowded strong signals can beclearly extracted from the noise.
Eight-channel RTTY TX memoryThe built-in RTTY demodulator anddecoder allow you to check the callsign ofthe station on the air instantly. The‘756PROIII has 8 channels of RTTYtransmit memory. You can edit and sendup to a 62 character message for eachmemory channel without a PC or otherexternal unit.
Other features[Antenna and receiver] • Built-in autoantenna tuner • 2 TX/RX antenna connec-tors and RX antenna connector • 30kHz–60MHz general coverage* (*Some frequency ranges are not guaranteed)• Built-in RX attenuator (6/12/18dB) • Twinpeak audio filter • Dual watch • Digital twinPBT • Manual notch • Auto notch filter[Transmitter] • Tx monitor function • Toneencoder • VOX operation • All mode powercontrol • External Control for VoiceMemory and Memory Keyer[CW mode] • CW Wave form controlled bythe DSP • Multi-function electronic keyerincludes adjustable keying speed anddot/dash ratio, polarity, bug keyer • Continuously adjustable CW pitch controlfrom 300–900Hz • Double key jacks (Frontand rear) • Full break-in (QSK) • CW reverse[Operation] • 2 clocks shows local andUTC time • Screen saver • Set modemenu for speedy setting • Analog and dig-ital meter indicates relative output power,SWR, ALC level and compression level • Memory pad stores up to 5 or 10 operat-ing frequencies and modes • Quick splitfunction • RF gain and squelch control • ±9.999kHz Adjustable RIT and ∂TX • 1Hz step tuning and display • 101 mem-ory channels with 10-character channelname • Optional Voice synthesizerannounces the operating frequency, modeand signal strength in English • Program,memory, select memory, ∂f scans • Autotuning step function • Dial lock
+30dBm IP3*Using receiver design techniques intro-duced in the IC-7800, Icom’s engineeringteam focused on producing a distortion-free, high-dynamic-range. To achieve thisgoal, Icom used higher-grade componentsin vital receiver sections of the ‘756PROIII.* Under the condition of receive frequency 14.2MHz,
input frequencies 14.3MHz and 14.4MHz, Pre-ampOFF, mode USB BW: 2.4kHz
Two newly designed preamplifiersTo minimize distortion and maximizedynamic range, the ‘756PROIII preampli-fiers use the same basic circuit design asthe IC-7800 preamplifiers. Preamp-1 is anoiseless feedback design, with push-pullamplifiers. Preamp-2 uses bipolar transis-tors for higher gain. It is ideal for usingseparate low-efficiency receiving anten-nas such as small loops or Beverages.
455k
Hz
36kH
z
3Lo
ManualNOTCH
IFFilter
DET
AGC
AGCDSPD/A
D/AA/D AF
+30dBm IP3
Two newly designed preamplifiers
Real time spectrum scopewith mini scope function
Real time spectrum scope withmini scope functionThe real time spectrum scope is now anindispensable tool for top performing HFradios. The ‘756PROIII’s spectrum scopeadds a mini scope function. The miniscope allows you to monitor the scopescreen while you use other functionmenus. For exam-ple, you can moni-tor the scopescreen even whileyou are changingthe IF filter shapeand passbandwidth.
Adjustable SSB transmit BWWith the flexible DSP-based waveformshaping, you can tailor your transmit audioquality to suit your operating style. TheSSB transmit bandwidth is selectable from100, 300 and 500Hz at the high-passedge, and 2500, 2700 and 2900Hz at thelow-pass edge respectively. 3 types ofhigh and low combinations can be storedin the memory.
32-bit floating point DSP & 24-bit AD/DA convertersThe heart of the ‘756PROIII is the provencombination of the 32-bit floating pointDSP and 24-bit AD/DA converters. Thispowerful combination supports the manydigital processing features of the‘756PROIII.
Sharp and soft filter shapesSelect an appropriate filter shape, depend-ing on your operating style or band condi-tions. Independent SSB and CW filters giveyou the flexibility you want while listening tothe signal.Preamp-1 Preamp-2RF stage & Preamplifiers
Mini scope screen
32-bit DSP technologyThe IC-746PRO/7400 covers HF, 50MHzand 144MHz bands with full IF DSP capa-bility. The combination of the 32-bit DSPand 24-bit AD/DA converter is comparableto the IC-756PROIII, providing flexible sig-nal enhancing, superior interferencereduction and other advanced digital fea-tures in all bands. Clear signals withoutdistortion are realized in any signal condi-tions.
IF filter shapes You will never have to purchase optionalfilters, with over 51 different filter widths,just dial in the width you want. Then selectwhether you want a sharp or soft filtershape for SSB and CW modes.
RTTY demodulator and decoderThe built-in RTTY demodulator and decoderreads baudot RTTY signals on the screenwithout turning on your PC or other gear. TheRTTY tuning indica-tor helps critical tun-ing. The Twin Peakfilter removes inter-fering QRM givingyou a more accuratedecoded message.
Other features• Large, multi-function LCD • Digital twinPBT • DSP controlled AGC loop • 108DTCS and 50 CTCSS codes standard • Built-in Automatic antenna tuner • Memo-pad • 4-channel memory keyer with 50characters • FM narrow capability • Tripleband stacking register • Quick split • VSCfunction • Optional voice synthesizer
32-bit DSP with 24-bit AD/DAconverter
51 types of passband width, soft and sharp filter shapes
100W output on all HF, 50MHzand 144MHz bands
Simple, straight forward operation with keypad
General coverage receive withsuperior performance
Optional DSP capability
Simple operationThe IC-718 is equipped with a minimumnumber of buttons and controls for simplefeature selectability. The 10-key pad on thefront panel allows direct entry of an operatingfrequency, or a memory channel number.The auto tuning step function is activatedwhen turning the dial quickly and helps quicktuning. The band stacking register is conve-nient when changing operating bands.
Front mounted loud speakerThe IC-718 has the speaker mounted onthe front panel. With the speaker facing theoperator, audio sounds can be clearly heardwithout impediment during operation.
Optional DSP capability, UT-106The optional DSPunit gives you noisereduction and autonotch filter functionsfor extra receiverperformance.
General coverage receiverThe IC-718 has 0.03–29.999999MHz*general coverage receive capability. *Guaranteed range: 0.5–29.999999 MHz
Other features• Built-in electronic keyer • Combinedsquelch and RF gain control • 101 memo-ry channels • CW full break-in • Built-inmicrophone compressor • Preamplifierand attenuator • IF shift interference rejec-tion • 1Hz tuning • Digital S/RF meter• VOX function for hands-free operation• Optional automatic antenna tuner
Optional UT-106
RTTY decode screen
HF/VHF/UHF ALL MODE TRANSCEIVER
Covers all HF, 6m, 2m and70cm bands
Clean, stable and powerfuloutput power
Built-in DSP capability (Optional depending on version)
HF to 70cm band coveragewith 100W* output The IC-706MKIIG covers from HF band to430/440MHz band. Of course, all modeoperation (SSB, CW, RTTY, AM and FM) ispossible and a full 100W of output poweris available for HF and 6m operation; 50Wfor 144MHz and 20W for 430/440MHzoperation.(* HF, 50MHz band only)
DSP features with UT-106DSP capabilities are available*. Theseinclude noise reduction and auto notchfunctions. Superior receive quality in yourshack, vehicle or during DX’peditions.* UT-106 DSP unit required for some versions.
Compact with detachable panelWith an optional separation cable, OPC-581/OPC-587, the detachable front panelallows easy installation in your shack or ina wide variety of mobile applications.
High stability transmitterMOS-FET power amplifiers in the PA unitprovide stable, high quality output with lowIMD and low spurious emissions even dur-ing full duty cycle and extended operation.
Other features• Built-in tone squelch functions • Automaticrepeater function • Simple band scope func-tion • Narrow FM capability • Up to 3 selec-table passband widths with optional filters• Built-in electronic keyer • IF shift interfer-ence rejection • Continuously adjustable RFoutput • Adjustable SSB carrier point • Optional automatic antenna tuner
IF DSP — First in the class
Two-point MNF attenuates more than 70dB
2.5 inch color TFT display
IF DSP — first in this classDigital IF filter, manual notch filter, digitaltwin PBT, AGC loop management, digitalnoise reduction and more. The latest digi-tal features are incorporated in this com-pact radio from two DSP chips that deliversuperior processing performance. Ofcourse, those digital features work on allham bands, from HF, 50, 144MHz to the430/440MHz band.
2-point MNF (Manual notch filter)Pull out the weak signals in crowded bandconditions with Icom’s new two-point MNF(manual notch filter). Apply 70 dB of rejectionto two signals at once! Notch width isadjustable – wide, middle and narrow – andan auto-tuning notch filter is available, too.
2.5 inch color TFT displayThe 2.5 inch color TFT display presentsnumbers and indicators in bright, concen-trated colors for easy recognition. You canchoose from 3 background colors and 2font styles to suit your preference. Thevideo output jack allows you to view a mag-nified display on a TV or external monitor*.* 3.5(d) mm monaural cable is required.
Other outstanding features• 35W output in 70cm band • ±0.5 ppm highstability crystal unit • 8 direct access but-tons for user friendly operation • Digitalvoice recorder for transmit and receive • Built-in RTTY demodulator • Remote con-trol microphone, HM-151 • Fixed mode andcenter mode band scope • Multi functionmeter and SWR graphic display • Frontpanel separation with optional separationcable • Built-in voice synthesizer
is equipped with equivalent features forreceiving as the main band such as AF vol-ume and RF-gain/squelch control knobs.
Satellite communicationThe optional AG-2400 converts a 2.4GHzsatellite downlink signal to a 144MHz signal.Coupled with thesatellite mode of theIC-910H, the USmode and LS (UX-910 required) modesatellite operation isready for use.
Other features• Continuously adjustable Tx output power• Optional UX-910 for 1200MHz bandoperation • Sweep function • IF shift func-tion • Up to 2 optional DSP units can beinstalled • FM-narrow mode receivable • CTCSS tone encoder/decoder • 9600bpsPACKET capability • Memory pad function• Optional CW narrow filter
Maximum portable convenienceThe IC-703 is designed for outdoor, portableoperation. The optional battery pack, BP-228 provides 5W output power* and 7hours* operating time. All the necessaryequipment including an antenna, can bepacked in the optional multi-bag LC-156.* 2W in AM mode. Tx:Rx:Stand-by=0.5:0.5:9 in SSB mode.
Built-in automatic antenna tuner The built-in antennatuner covers from1.8MHz to 54MHz.Ideal for moving aboutduring portable opera-tion. Latch relays usedin the antenna tunergreatly reduce thepower consumption.
DSP capabilitiesThe built-in DSP unit provides noisereduction and auto notch functions. * UT-106 DSP unit required for some versions.
Other features• Standard ±0.5ppm high stability TCXO • Detachable controller with optional sepa-ration cables, OPC-581/OPC-587 • Frontand rear microphone jacks • RIT, VOX,noise blanker and speech compressorstandard • 9600bps data terminal • 3-channel memory keyer • RTTY (FSK)mode available • Key backlighting
Built-in automatic antenna tuner for portable operation
Optional multi-bag, battery pack for field use
Built-in DSP Capabilities(Optional depending on version)
100W output on 2m band & 75W output on 70cm band
Simultaneously works two bands
Excellent support for satellitemode and PACKET operation
Built-in antenna tuner
100W of stable output power A powerful 100W* of output power is pro-vided by the power amplifier circuit. Thecombination of the aluminum die-castchassis ensures stable output. * 75W on 430/440MHz and 10W on 1200MHz band
Simultaneously works two bandsThe IC-910H can receive two bands simul-taneously in different modes. The sub-band
Optional AG-2400
Optional LC-156
Digital Voice + 950 bps data*The ID-800H can transmit and receive D-STAR format digital voice and 950 bpsdata communication, simultaneously. TheDigital features of the ID-800H are com-patible with IC-2200H, IC-V82 and IC-U82radios with the optional UT-118 installed.In addition, analog FM mode is also avail-able. * Theoretical value.
Digital Voice + 950bps data capability
GPS coordination
Calling by callsign
128kbps data and 4.8kbps digital voice communication
PC remote control software
Useful callsign functions
4.8kbps DV (digital voice) modeand 128kbps DD (data) mode*The ID-1 has three modes — analog FM,digital voice and data mode operation. Thebuilt-in AMBE® vocoder chip provides digi-tally modulated clear sound as well as128kbps wireless data transmission. In DDmode operation, you can use various inter-net applications wirelessly by connecting toa PC with Ethernet and USB cables. * Theoretical value.
PC remote controller suppliedThe PC controller software is supplied withthe ID-1. When the ID-1 is connected to aPC, most functions of the ID-1 can be con-trolled from the PC screen. The controllersoftware is convenient for editing memorychannels, writing short data messages,and checking received call records, etc.
Useful callsign functionsThe ID-1 embeds your own and the calledstation’s callsign in your digital modetransmission. The calling station’s callsignis displayed on the receiving station and anewly received callsign can be automati-cally stored in the memory. Of course, CQcall is also possible.
Other Features• Digital callsign squelch (DSQL) and digi-tal code squelch (CSQL) • Short data mes-sage in DV mode • Automatic FrequencyControl (AFC) function for FM and DV mode• S-meter squelch • Programmed, memoryand select mode scan • Break-in commu-nication • Enhanced Monitor Request(EMR) function • Auto repeater function forFM mode* • Stand-by beep* Depending on version.
GPS Coordination dataWhen an external GPS receiver (NMEA0183 format) is connected to the ID-800H,yours and other station’s position informa-tion can be exchanged and shown on thedisplay. When the receiving side is con-nected to a PC*, map plotting is possible.Supported data formats are GLL, GGA,RMC, GSA and VTG sentences. * Map plotting software required (Not suppliedby Icom ).
Calling by callsignIn the digital voice mode, your callsign andthe calling station’s callsign (or CQ mes-sage) are included in each transmission.The callsign squelch allows you to choosean incoming call selected by the callsign.Also, received callsigns are automaticallystored in the memory.
Other Features• Powerful 55W/50W (VHF/UHF) outputpower • Total 512 alphanumeric memorychannels • Wideband receiver • Amber,green and yellow, triple color LCD illumi-nation • CTCSS, DTCS tone • 16 DTMFmemory channels • Detachable front panel
V/V, U/U simultaneous receivecapabilityThe IC-2720H/2725E is a unique dual bandmobile, providing VHF/VHF, UHF/UHFsimultaneous receive capability. Simpletouch of a button changes the transmitband. In addition, its wideband receivercovers from 118–549 and 810–999MHz*,you will be able to listen to almost anycommunications!* Receiver range differs depending on version.
Independent controls for each bandThe IC-2720H/2725E provides separatetuning, volume, squelch knobs and func-tion buttons for the left and right sidebands. A wide LCD display shows bothband settings in an easy to read side byside format. Also, listen to both bandsindependently through separate left andright band audio jacks.
Compact, remote controllerThe combination bracket, MB-85 or the con-troller bracket, MB-84 is supplied as stan-dard, depending on version. The MB-85allows mounting of the controller on themain unit. The MB-84 offers the flexibilityof mounting the controller, while placingthe main unit in an out-of-the-way location.
Other Features• 50W/35W (VHF/UHF) output power • Total212 memory channels • Built-in 50 CTCSS,104×2 DTCS tones • 9600bps packet dataterminal • Sub band auto mute function • 14DTMF memory channels • Microphonejacks are located on both the controllerand the main unit • Weather alert* • Autorepeater function* * Depending on version.
55W/50W (VHF/UHF) output powerIndividual MOS-FET power amplifier mod-ules supply the power for Icom’s mostpowerful analog dual band mobile with55W/50W (VHF/UHF). Stable power forlong distance communications.
Wideband receiverThe IC-208H/E208 wideband receivercovers 118–173, 230–549 and 810–999
MHz* as standard. Listen to your AmateurVHF/UHF bands, as well as aviation,marine, weather and other utility commu-nications in a compact mobile package. * Receiver range differs depending on version.
Detachable front panelThe 3.5m (11.5ft) separation cable, OPC-600/R, is supplied with the radio allowingthe compact remote control head* to beinstalled almost anywhere. * 111(W)×40(H)×26.3(D) mm; 43⁄8×19⁄16×11⁄32 in.
500 alphanumeric memory channelsWith this much memory, you can fill yourIC-208H/E208 with your favorite frequen-cies and operation settings such as outputpower, tone, and more! Then name eachmemory channel with up to 6 charactersfor quick channel identification.
Other Features• Easy to manage bank link scan system • Amber, green and yellow, triple color LCDillumination • 50 CTCSS, 104×2 DTCSencoder/ decoder • Pocket beep and tonescan • 16 DTMF memory channels •9600bps packet data terminal
Powerful output power55W/50W (VHF/UHF)
Wideband receiver(Depending on version)
Compact, detachable front panelwith separation cable
V/V, U/U simultaneous receive capability
Wideband receiver(Depending on version)
Flexible installation with compact remote controller
75W of output powerThe combination of Icom’s one piece, die-cast aluminum chassis and MOS-FETpower amplifier gives you a powerful 75Woutput power. Your communications willget through.
Dynamic Memory Scan (DMS)With 200 alphanumeric memory channels,Icom’s exclusive DMS system gives you
flexibility over your scanning lists neveroffered before in a 2m mobile, fully cus-tomizable into 10 banks.
HM-133V, remote control microphoneThe backlit HM-133V*, gives you control ofyour IC-V8000 in the palm of your hand.The Icom exclusive “Hot keys” (F1/F2)memorize the transceiver full settings. Asif switching between two separate radios,all operating frequencies, tone settings aswell as the display color, fan speed, andset mode settings are memorized. * Optional for some versions.
Other Features• Front mounted speaker • Amber andgreen backlit LCD • Built-in 50 CTCSS and104×2 DTCS tones • Pocket beep andtone scan • Rugged construction • Standard DTMF encoder • OptionalDTMF decoder, UT-108 • 10dB squelchattenuator • Weather channel with weath-er alert* • FM narrow switchable capabili-ty* • Cloning capability from PC orbetween radios (* Depending on version)
Stable 65W output power
Optional digital unit, UT-118
User-friendly interface anddurable construction
Unbeatable 75W output power with efficient cooling fan
Total 200 memory channels with 10 memory banks
Remote control microphone, HM-133V
65W* of output powerA MOS-FET power amplifier provides65W* of stable output power. A one piece,aluminum chassis helps to keep the trans-ceiver cool and provides durable long-last-ing construction. (* Depending on version.)
Optional digital unit, UT-118The optional UT-118 provides D-STAR for-mat digital voice and data communication
at 4.8kbps, compatible with ID-800H andUT-118 installed IC-V82. When connectedto an external GPS receiver*, positioninformation can be exchanged with otherstations. (* NMEA 0183 output and RS-232Cinterface are required.)
Simple operationThe large tuning dial provides easy accessto active channels even without looking atthe front panel. Secondary functions areeasily recalled by holding the buttons.
CTCSS and DTCS operationThe IC-2200H contains 50 CTCSS and104×2 DTCS encode/decode plus tonescan functions. The “pocket beep” featuregives you an audible and visual indicatorof an incoming call.
And more…• Total 207 alphanumeric memory channel• 24 DTMF autodial memories • DTMFcode squelch and pager function withoptional DTMF decoder, UT-108 • 10dBsquelch attenuator • Weather channelwith weather alert function (U.S.A. versiononly) • FM narrow mode (Depending on ver-sion)
With optional UT-118
VHF/UHF DUAL BAND FM TRANSCEIVERS
VHF/UHF MULTIBAND FM TRANSCEIVERS
VHF/UHF DUAL BAND FM TRANSCEIVER
6W powerful output for both 144 and 430(440) MHz bands*1
MIL standard durable construction
Built-in tone squelch with tonescan and pocket beep functions
Other Features• Large, easy-to-push PTT switch • 50 CTCSS toneencoder/decoder with pocket beep and tone scanfunctions • Optional HM-75A, microphone for simpleremote control • Thumb-touch lock switch • Channelindication • 9 DTMF memories with up to 16 digitseach • Auto power saver with selectable duty • multi-ple scans provide versatile signal detection • Autopower off • Auto repeater function*2 • LCD backlightwith timer*1 Typical; with 13.5V DC. *2 Depending on version
Ultra compact, light weight body—47(W)×81(H)×28(D)mm, 160g*1
Mini-power dual bander with wideband receive capability
20 hours*2 of operating time with slim battery pack
5W output power on 50, 144, and 430(440)MHz band
Wideband receiver— 495kHz to 999.990MHz*1 —
555 alphanumeric memory with18 memory banks
Other features• Up to 5–6 hours*2 of operating time with suppliedLithium-Ion battery pack • 104×2 DTCS or 50 CTCSScodes • Compact body with splash resistance(Equivalent to IPX4) • 10 DTMF memories • Morse codesynthesizer • High speed scanning • 13 scanningmodes • Antenna tip replaceable for 50MHz band • PC Programmable • Backlit LCD • Green, orangeand yellow selectable backlit keypad color *1 Receiver range differs from depending on version.*2 Tx:Rx:Stand-by=1:1:8
Other features• Simple operation and stylish design • Built-in 50CTCSS and 104×2 DTCS tones • 1000 regular mem-ory channels with 6-characters alphanumeric naming• 18 memory banks (Max. 100 Ch per bank) • Bank linkscan • Auto memory write scan • Auto power off • Large backlit LCD • Rapid charger, BC-164 is sup-plied • Weather channel with weather alert*3 • 10dBattenuator • Priority watch with priority beep *1 127/32×33/16×13/32 in; Projections are not included, 5.6oz; includingbattery pack and antenna. *2 Tx:Rx:Stand-by=5:5:90 *3 Dependingon version.
144MHz 430(440)MHz
VHF AND UHF TRANSCEIVERS
5.5W (typ.) of powerful outputpower with supplied battery pack
MIL grade tough construction
Reversible up/down buttons and rotary selector
Other features• 16 button keypad for easy to access functions• Built-in 50 CTCSS and 104×2 DTCS tones withpocket beep and tone scan functions • 100 memorychannels with 5-characters alphanumeric naming • 5 DTMF memory channels • Optional, UT-108DTMF decoder • Fast scanning speed 40 channelsper second (Program scan only) • Auto squelch delay• PC programmable • Backlit LCD • Normal andreverse semi-duplex setting • Long and short, autosquelch delay
7W output power on 144MHz 5W for 430(440) MHz
Optional UT-118 provides D-STARformat digital voice and data
200 alphanumeric memorieswith 10 memory banks
Other features• 104×2 DTCS or 50 CTCSS tone codes • Weatherchannel receive with weather alert*1 • Automaticrepeater function*2 • 16 DTMF memories • Durableconstruction and simple operation • Backlit LCD • Reversible control knob and up/down buttonsassignment • PC Programmable • Optional UT-108DTMF decoder • Power save function • Variousscanning functions including program, memory, skip,priority and tone scan • FM narrow mode capability*1 IC-V82 USA version only, *2 USA version only
With optional UT-118
AH-703Covers 7, 14, 21, 28, 50MHz bands.
AH-703Covers 7, 14, 21, 28, 50MHz bands.
AH-2bCovers 7–54MHz.AH-2bCovers 7–54MHz.
ANTENNA ELEMENTSLINEAR AMPLIFIER
CT-17 LC-156
CI-V CONVERTER
OPTIONS FOR DESKTOP & PORTABLE TRANSCEIVERS
IC-PW1/EUROPS-12513.8V/25A
: Applicable : Not applicable
MULTI-BAG
HM-36 HM-103 HM-151*1
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
MODEL NAME HM-12
HAND MICROPHONESSM-6 SM-20
DESKTOP MICROPHONES
(Use with OPC-589)
(Use with OPC-589)
(Use with OPC-589)
SP-10 SP-21
SP-23
SP-20
EXTERNAL SPEAKERS
appr
ox. 2
4.5
m; 8
0.3
ft
30 m; 98.4 ft
AH-710MODEL NAME AH-4Matches 3.5–54MHz bands.
AT-180
ANTENNA TUNERS FOLDED DIPOLE ANTENNA
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
(Use with OPC-599)
(Use with OPC-599)
(Use with OPC-599)
DC POWER SUPPLY
*2
(Use with OPC-1248)
FL-100500Hz/–6dBFL-101250Hz/–6dBFL-1032.8kHz/–6dBFL-2231.9kHz/–6dBFL-232350Hz/–6dB
FL-52A500Hz/–6dBFL-53A250Hz/–6dBFL-2221.8kHz/–6dBFL-2573.3kHz/–6dB
FL-132500Hz/–6dB(for Main band)FL-133500Hz/–6dB(for Sub band)
FILTERS
(Up to two filters)
(One of these filters)
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
MODEL NAME
HIGH STABILITY CRYSTAL UNITS
(CR-338 installed)
CR-293Frequency sta-bility: ±0.5ppm
CR-338Frequency sta-bility: ±0.5ppm
DSP UNITVOICE SYNTHESIZERUT-102 UT-106
(Installed depending on version)
(Installed depending on version)
(Installed depending on version)
(Up to two units)
CR-282Frequency sta-bility: ±0.5ppm
(One of these filters)
FILTERS
EXTERNAL SPEAKERS
*1 For exclusive use with IC-7000 only.*2 When used with a compact mobile type antenna, the IC-703 may receive switching noise from the PS-125.
OPTIONS FOR DESKTOP & PORTABLE TRANSCEIVERS
: Applicable : Not applicable
AG-25144MHz. Notavailable forEU countries
AG-35430MHz. Notavailable forEU countries
OPC-5813.5m;11.5ftOPC-5875.0m;16.4ft
OPC-14433.5m;11.5ftOPC-14445.0m;16.4ft
MODEL NAME OPC-5898-pin connectormicrophone to8-pin modular
OPC-59913-pin ACCsocket to 7-, 8-pin ACC sockets
OPC-59813-pin ACC longcable for AT-1807.0m;22ft
OPC-12483-pin DC cable to6-pin connector.
MIC ADAPTER CABLE ADAPTER CABLEACC CABLEOPC-742Connectioncable betweentransceiver andAT-180 with2m/70cm linearamplifier.
ACC 13-PIN CABLE POWER SUPPLY ADAPTER
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
BP-2289.6V/2800mAh(Ni-Cd)
MB-23MODEL NAME MB-72 MB-106 IC-MB5 MB-62 MB-63 MB-105
MB-65
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
(Use with MB-63)
(Use with MB-105)
(Use with MB-63)
UX-910AG-2400Converts 2400–2402MHz to144 –146MHz.
MODEL NAME
IC-7800IC-756PROΙΙΙΙΙΙIC-746PRO, IC-7400IC-718IC-7000IC-706MKΙΙΙΙGIC-703IC-910H
1200MHz BAND UNIT
BC-155A/D
BATTERY PACK CHARGER CARRYING HANDLES MOBILE MOUNTING BRACKETS CONTROLLER BRACKET
MOUNTING BASES SEPARATION CABLES
WATERPROOF PREAMPLIFIERS DOWN CONVERTEROPC-025A20A cableOPC-025D30A cableOPC-12294A cableOPC-145730A cable
OPC-63920A cable withNoise FilterOPC-1457R30A cable withNoise Filter
For Europe versions
DC POWER CABLES
(Use OPC-025D)
(Use OPC-025A)
(Use OPC-1457)
(Use OPC-1457R)
(Use OPC-025D)
(Use OPC-1229)
(Use OPC-025D)
(Use OPC-639)
(Use OPC-025D)
OPTIONS FOR MOBILE TRANSCEIVERS
: Applicable : Not applicable
CONTROLLER BRACKETS MOUNTING BASE
MODEL NAME MB-58 MB-84 MB-65HM-133/Vw/DTMF keypad
HM-154Tw/DTMF keypad
HM-154
HAND MICROPHONES
(Use HM-133V)
(Use HM-133V)
(Use HM-133)
(Use HM-133)
(Use HM-133)
ID-1ID-800HIC-2720H, IC-2725EIC-208H, IC-E208IC-V8000IC-2200H
DC POWER CABLES
MODEL NAME OPC-600/R3.5m: 11.5ftOPC-601/R7.0m: 23ft
OPC-5898-pin connectormicrophone to8-pin modular
OPC-1384For PC, GPSconnection
SP-22SP-10OPC-4415.0m: 16.4ft
OPC-4405.0m: 16.4ft
MB-85 OPC-3477.0m: 23ftOPC-11323.0m: 9.8ft
OPC-11563.5m: 11.5ftwith modularcable
COMBINATION BRACKET
ID-1ID-800HIC-2720H, IC-2725EIC-208H, IC-E208IC-V8000IC-2200H
MODEL NAME OPC-474Between trans-ceivers
CS-208CS-2200HCS-2720CS-D800CS-V8000
UT-108 OPC-478UTransceiver to PCUSB cable
OPC-478Transceiver to PCRS-232C cable
(Use CS-2200H)
(Use CS-V8000)
(Use CS-208)
(Use CS-2720)
(Use CS-D800)
ID-1ID-800HIC-2720H, IC-2725EIC-208H, IC-E208IC-V8000IC-2200H
(Use with MB-58)
(Use with MB-58)
(Use with MB-84)
UT-118
SEPARATION CABLES SPEAKER CABLE MICROHONE CABLE MIC ADAPTER CABLE DATA CABLERC-24
CONTROLLEREXTERNAL SPEAKERS
DTMF DECODER UNIT DIGITAL UNIT CLONING CABLES CLONING SOFTWARE
(D-STAR ready)
(D-STAR ready)
(Use with BC-119N)
(Use with BC-119N)
OPTIONS FOR HANDHELD TRANSCEIVERS
CIGARETTE LIGHTER CABLES
CIGARETTE LIGHTER CABLES DC POWER CABLE
CHARGER ADAPTERS
OPC-254L
CP-12Lw/noise filter
CP-21LRw/noise filter
CP-19Rw/noise filter
(Use with BC-119N)
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME
AD-56 AD-94 AD-101
SPEAKER-MICROPHONESHM-46/L HM-54 HM-75A HM-131 HM-158L
: Applicable : Not applicable
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME BP-170AA(LR6)×4 cells
BP-1739.6V/650mAh(Ni-Cd)
BP-1807.2V/600mAh(Ni-Cd)
BP-1714.8V/700mAh(Ni-Cd)
BP-1724.8V/950mAh(Ni-Cd)
BP-208NAA(LR6)×6 cells
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME BP-222N7.2V/600mAh(Ni-Cd)
BP-2177.4V/1300mAh(Li-Ion)
BP-2433.7V/1800mAh(Li-Ion)
BP-210N7.2V/1650mAh(Ni-MH)
BC-110A/D/V/AR/DR 12V/200mA
WALL CHARGER
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME
BC-119NRapid charger
BC-139Rapid chargerIncludes AC adapter.
BC-144NRapid charger
BC-164Rapid charger
BC-146Regular charger
(Use with AD-56+BC-145)
(Use with AD-101+BC-145)
(Use with AD-94+BC-145)
(Use with BC-147)
(Use with BC-147)
(Use with BC-145)
(Use with BC-145L)
(Use with BC-145)
BP-209N7.2V/1100mAh(Ni-Cd)
BP-216AA(LR6)×2 cells
AC ADAPTERS
(Use with BC-146)
(Use with BC-164)
(Use with BC-144N or BC-119N)
(Use with BC-146)
(Use with BC-164)
(Use with OPC-782)
(Use HM-46)
(Use HM-46)
(Use HM-46L)
(Use with BC-144N or BC-119N)
BC-14516V/1A
BC-145L16V/1A
BC-14712V/200mA
(Use with BC-119N)
BP-211N7.4V/1800mAh(Li-Ion)*1
BATTERY CASES BATTERY PACKS
BATTERY PACKS DESKTOP CHARGERS
*1 Charge with BC-119N + AD-101.
(Use HM-128 with OPC-782)
(Use HM-128L)
EARPHONE-MICROPHONESHM-128/L HM-153P
HS-95Behind-the-headtype
HS-97Throat microphonetype
: Applicable : Not applicable
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME
OPTIONS FOR HANDHELD TRANSCEIVERS
CLONING SOFTWARE
IC-T90A, IC-E90IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME
ANTENNASCS-P7CS-T7CS-T90ACS-V8CS-V82
FA-1443BFA-B2EFA-B270CFA-B70CFA-S270CFA-S6270D
(Use FA-B2E)
(Use FA-1443B/B270C)
(Use FA-B2E/B70C)
(Use FA-S270C)
(Use FA-S6270D)
(Use CS-V8)
(Use CS-V82)
(Use CS-T7)
(Use CS-P7)
(Use CS-T90A)
AD-92SMABNC type antennaconnector
ANTENNA ADAPTER
MB-96FFixed type
(Use with MB-83 swivel joint)IC-T90A, IC-E90
IC-T7HIC-P7A, IC-E7IC-V82, IC-U82IC-V8, IC-T3H
MODEL NAME
(Use with BP-173/BP-180)
LC-137
CLONING CABLESOPC-478Transceiver to PCRS-232C cable
OPC-474Between transceivers.
UT-108 UT-118LC-152A LC-161
(Use with BP-170/171/172)
LC-136
MB-103Alligator type.
BELT CLIPSMB-86Swivel type.
MB-83Swivel type.
OPC-782
MB-96NSwivel type. MB-86swivel joint supplied.
VS-1L
VOX/PTT CASE
(Use with VS-1L)
(Use with VS-1L)
OPC-478UTransceiver to PCUSB cable
HS-94Earhook type withboom microphone
(Use with VS-1L)
PLUG ADAPTER CABLESP-13
(Use with OPC-782)
EARPHONEHS-85
HEADSETS
BELT CLIPS LEATHER BELT HANGERS CARRYING CASES DTMF DECODER UNIT DIGITAL UNIT
SPECIFICATIONS
IC-756PROIII IC-746PROIC-7400IC-7800
All stated specifications are subject to change without notice or obligation.The LCD display may have cosmetic imperfections that appear as small or dark spots. This is not a malfunction or defect, but a normal characteristic of LCD displays.
Tx: 1.8, 3.5, 7, 10, 14, 18, 21, 24, 28, 50, 144MHz bands
Rx: 30kHz–60MHz, 108–174MHz*1
*1 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, AM, FM
±7ppm (From 1 min. to 60 min. after power ON)
23A at 13.8V DC
13.8V DC ±15%
SO-239 × 3 (2 for HF/50MHz and1 for 144MHz bands; 50Ω)
102(99 regular, 2 scan edges and 1 call)
287×120×316.5 mm;115⁄16×423⁄32×1215⁄32 in
9.0kg; 19.8lb
SSB, CW, RTTY, FM: 5–100WAM: 5–40W
Less than –50dB (HF)Less than –60dB (50/144MHz)
More than 40dB
More than 55dB
8-pin connector (600Ω)
SSB, CW, RTTY, FM (2.4kHz):1.8–29.999MHz 0.16µV50–54MHz 0.13µV144–148MHz 0.11µV
AM: 0.5–1.8MHz 13µV(6kHz) 1.8–29.999MHz 2.0µV
50–54MHz 1.0µV144–148MHz 1.0µV
FM: 28–29.999MHz 0.5µV(15kHz) 50–54MHz 0.25µV
144–148MHz 0.18µV
SSB: 2.4kHz/–6dB(2.4kHz) 3.2kHz/–40dB
3.6kHz/–60dB4.3kHz/–80dB
CW: 500Hz/–6dB(500Hz) 700Hz/–60dBRTTY: 360Hz/–6dB(350Hz) 650Hz/–60dBAM: 6.0kHz/–6dB(6kHz) 15.0kHz/–60dBFM: 12kHz/–6dB(15kHz) 20kHz/–60dB
*variable between 50Hz and 3.6kHz
More than 70dB (HF, 50MHz bands)More than 60dB (144MHz band)(Except IF point on 50MHz band)
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Tx: 1.8, 3.5, 5*1, 7, 10, 14, 18, 21, 24, 28, 50MHz bands
Rx: 30kHz–60MHz*2
*1 Depending on version.*2 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, AM, FM
±0.5ppm(–10˚C to +50˚C; +14˚F to +122˚F )
23A at 13.8V DC
13.8V DC ±15%
SO-239 × 2 + phono [(RCA) 50Ω]
101 (99 regular, 2 scan edges)
340×111×285 mm;133⁄8×43⁄8×117⁄32 in
9.6kg; 21.2lb
SSB, CW, RTTY, FM: 5–100WAM: 5–40W
Less than –50dB (HF)Less than –60dB (50MHz)
More than 40dB
More than 55dB
8-pin connector (600Ω)
SSB, CW, RTTY (2.4kHz):1.8–29.999MHz 0.16µV50–54MHz 0.13µV
AM: 0.5–1.799MHz 13µV(6kHz) 1.8–29.999MHz 2.0µV
50–54MHz 1.0µVFM: 28–29.999MHz 0.5µV(15kHz) 50–54MHz 0.32µV
SSB, RTTY: 2.4kHz/–6dB(2.4kHz) 3.2kHz/–40dB
3.6kHz/–60dB4.3kHz/–80dB
CW: 500Hz/–6dB(500Hz) 700Hz/–60dBAM: 6.0kHz/–6dB(6kHz) 15kHz/–60dBFM: 12kHz/–6dB(15kHz) 20kHz/–60dB
*variable between 50Hz and 3.6kHz
More than 70dB
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Tx: 137kHz*1, 1.8, 3.5, 5*1, 7, 10, 14, 18, 21, 24, 28, 50MHz bands
Rx:30kHz–60MHz*2
*1 Depending on version.*2 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, PSK31, AM, FM
±0.05ppm (0˚C to +50˚C; +32˚F to +122˚F, after warm up)
800VA
85–265V AC
SO-239 × 4 + BNC × 2 (50Ω)
101 (99 regular, 2 scan edges)
424×149×435 mm;1611⁄16×57⁄8×171⁄8 in
25kg; 55lb
SSB, CW, RTTY, PSK31, FM: 5–200WAM: 5–50W137kHz (CW): More than –20dBm
Less than –60dB (HF)Less than –70dB (50MHz)
More than 63dB
More than 80dB
8-pin connector (600Ω)
SSB, CW, RTTY, PSK31 (2.4kHz):0.1–1.799MHz 0.5µV1.8–29.999MHz 0.16µV50–54MHz 0.13µV
AM : 0.1–1.799MHz 6.3µV(6kHz) 1.8–29.999MHz 2.0µV
50–54MHz 1.0µVFM : 28–29.999MHz 0.5µV(15kHz) 50–54MHz 0.32µV
SSB 2.4kHz/–3dB(2.4kHz) 3.6kHz/–60dBCW 500Hz/–3dB(500Hz) 700Hz/–60dBRTTY, PSK31 360Hz/–6dB(350Hz) 650Hz/–60dBAM 6.0kHz/–3dB(6kHz) 15kHz/–60dBFM 12kHz/–6dB(15kHz) 20kHz/–60dB*variable between 50Hz and 3.6kHz
More than 70dB
More than 2.6W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω×2(for main and sub bands)
Tran
smit
ter
Rec
eive
r
Frequency coverage(Differs according to version)
Modes
Frequency stability
Maximum current drain
Power supply requirement
Antenna connector
Number of memory channels
Dimensions (W×H×D) ; Projections are not included.
Weight (approx.)
Output power
Spurious emissions
Carrier suppression
Unwanted sideband
Microphone connector
Sensitivity (typical)Preamp ONSSB, CW, RTTY, AM: at 10dB S/NFM, WFM: at 12dB SINAD
Selectivity
Spurious and image rejection
AF power at 10% distortion with an 8Ω load
External speaker connector
IC-718
Tx: 1.8, 3.5, 7, 10, 14, 18, 21,24, 28MHz bands
Rx: 30kHz–29.999MHz*1
*1 Guaranteed range 0.5–29.999MHz.
USB, LSB, CW, RTTY, AM
Less than ±200Hz (From 1 min.to 60 min. after power ON)
20A at 13.8V DC
13.8V DC ±15%
SO-239 (50Ω)
101 (99 regular, 2 scan edges)
240×95×239mm;97⁄16×33⁄4×913⁄32in
3.8kg; 8.4lb
SSB, CW, RTTY: 2–100WAM: 2–40W
Less than –50dB
More than 40dB
More than 50dB
8-pin connector (600Ω)
SSB, CW, RTTY1.8–29.999MHz 0.16µV
AM: 0.5–1.799MHz 13µV1.8–29.999MHz 2.0µV
SSB, CW, RTTY:2.1kHz/–6dB4.5kHz/–60dB
AM: 6.0kHz/–6dB20kHz/–40dB
More than 70dB(1.8–29.999MHz)
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Gen
eral
DESKTOP TRANSCEIVERS
SPECIFICATIONSG
ener
alTr
ansm
itte
rR
ecei
ver
IC-706MKIIG IC-703 IC-910H
All stated specifications are subject to change without notice or obligation.
*1 An optional UX-910, 1200MHz band unit is required for 1200MHz operation. *2 Guaranteed range 144–148, 430–450MHz
U.S.A. version:Tx: 144–148, 430–450,
1240–1300*1 MHzRx: 136–174*2, 420–480*2,
1240–1320*1 MHzEurope version:
Tx/Rx: 144–146, 430–4401240–1300*1 MHz
USB, LSB, CW, FM, FM-N(FM-N is not available in 1200MHz band)
±3ppm(–10˚C to +60˚C; +14˚F to +140˚F)
23A at 13.8V DC
13.8V DC ±15%
144MHz SO-239 (50Ω)430 (440) MHz Type-N (50Ω)1200*1MHz Type-N (50Ω)
328*1 (99 regular, 6 scan edges and 1 call for each band plus 10 satellite memories)
241×94×239mm;91⁄2×311⁄16×913⁄32in
4.5kg; 9.9lb (IC-910H)850g; 1.9lb (UX-910)
144MHz 5–100W430 (440) MHz 5–75W1200MHz*1 1–10W
Less than –60dB (144/430MHz)Less than –50dB (1200MHz*1)
More than 40dB
More than 40dB
8-pin connector (600Ω)
SSB, CW: 0.11µVFM: 0.18µV
SSB, CW: 2.3kHz/–6dB4.2kHz/–60dB
FM: 15kHz/–6dB30kHz/–60dB
FM-N: 6.0kHz/–6dB18kHz/–60dB
More than 60dB (144/430MHz band)More than 50dB (1200MHz band*1)
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω × 2(for Main and Sub bands)
Tx: 1.8, 3.5, 5*1, 7, 10, 14, 18, 21, 24, 28, 50*1 MHz bands
Rx:30kHz–60MHz*2
*1 Depending on version.*2 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, AM, FM
±0.5ppm(0˚C to +50˚C; +32˚F to +122˚F)3.0A typical at 13.8V DC (10W)2.0A typical at 9.6V DC (5W)
9–15.8V DC
SO-239 (50Ω)
105(99 regular and 6 scan edges )
167×58×200mm;69⁄16×29⁄32×77⁄8in
2.0kg; 4.4lb
SSB, CW, RTTY, FM: at 13.8V DC 0.1–10Wat 9.6V DC 0.1–5W
AM: at 13.8V DC 0.1–4Wat 9.6V DC 0.1–2W
Less than –50dB (HF)Less than –60dB (50MHz)
More than 40dB
More than 50dB
8-pin modular (600Ω)
SSB, CW:1.8–29.999MHz 0.16µV50–54MHz 0.13µV
AM: 0.5–1.8MHz 13µV1.8–29.999MHz 2.0µV50–54MHz 1.0µV
FM: 28–29.7MHz 0.5µV50–54MHz 0.25µV
SSB, CW: 2.4kHz/–6dB(2.4kHz) 4.0kHz/–60dBAM, FM-N: 9.0kHz/–6dB(6kHz) 20kHz/–50dBFM: 15kHz/–6dB(15kHz) 30kHz/–50dB
More than 70dB (HF)More than 65dB
(50MHz band; except IF point)
More than 1.0W (at 13.8V DC)More than 0.5W (at 9.6V DC)
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Tx: 1.8, 3.5, 7, 10, 14, 18, 21, 24, 28, 50, 144, 430(440)MHz bands
Rx:30kHz–199.999, 400–470MHz*1
*1 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, AM,FM, WFM* (*Rx only)
±7ppm (From 1 min. to 60 min. after power ON)
20A at 13.8V DC
13.8V DC ±15%
SO-239 × 2 (for HF/50MHz and 144/430(440)MHz bands: 50Ω)
107(99 regular, 6 scan edges and 2 call)
167×58×200mm;69⁄16×29⁄32×77⁄8in
2.45kg; 5.4lb
SSB, CW, RTTY, FM:1.8–50MHz 5–100W 144MHz 5–50W430(440)MHz 2–20W
AM: 1.8–50MHz 2–40W144MHz 2–20W430(440)MHz 2–8W
–50dB typical (HF)Less than –60dB (other bands)
More than 40dB
More than 50dB
8-pin modular (600Ω)
SSB, CW:1.8–29.995MHz 0.15µV50–54MHz 0.12µV144/430(440)MHz0.11µV
AM: 0.5–1.8MHz 13µV1.8–29.995MHz 2.0µV50–54MHz 1.0µV144/430(440)MHz1.0µV
FM: 28–29.7MHz 0.5µV50–54MHz 0.25µV144/430(440)MHz0.18µV
WFM: 76–108MHz 10µV
SSB, CW, RTTY: 2.4kHz/–6dB4.8kHz/–60dB
AM, FM-N: 8.0kHz/–6dB30kHz/–36dB
FM: 12kHz/–6dB30kHz/–50dB
More than 70dB (HF)More than 65dB (other bands;except IF point on 50MHz band)
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
IC-7000
Tx: 1.8, 3.5, 5*1, 7, 10, 14, 18, 21, 24, 28, 50, 144, 430(440)MHz bandsRx:30kHz–199.999, 400–470MHz*2
*1 Depending on version.*2 Some frequency ranges are not guaranteed.
USB, LSB, CW, RTTY, PSK31,AM, FM, WFM* (*Rx only)
±0.5ppm(0˚C to +50˚C; +32˚F to +122˚F)
22A at 13.8V DC
13.8V DC ±15%
SO-239 × 2 (for HF/50MHz and 144/430(440)MHz bands: 50Ω)
503(495 regular, 6 scan edges and 2 call)
167×58×180mm;69⁄16×29⁄32×73⁄32in
2.3kg; 5.1lb
SSB, CW, RTTY, FM:1.8–50MHz 2–100W 144MHz 2–50W430(440)MHz 2–35W
AM: 1.8–50MHz 1–40W144MHz 2–20W430(440)MHz 2–14W
Less than –50dB (HF)Less than –60dB (other bands)
More than 50dB
More than 50dB
8-pin modular (600Ω)
SSB, CW:1.8–29.999MHz 0.15µV50–54MHz 0.12µV144/430(440)MHz0.11µV
AM: 0.5–1.8MHz 4.0µV1.8–29.999MHz 2.0µV50–54MHz 1.0µV144/430(440)MHz1.0µV
FM: 28–29.7MHz 0.5µV50–54MHz 0.25µV144/430(440)MHz0.18µV
WFM: 76–108MHz 10µVSSB: 2.4kHz/–6dB(2.4kHz) 3.6kHz/–60dBCW: 500Hz/–6dB(500Hz) 900Hz/–60dBRTTY: 360Hz/–6dB(350Hz) 650Hz/–60dBAM: 6.0kHz/–6dB(6kHz) 15kHz/–60dBFM: 12kHz/–6dB(15kHz) 20kHz/–60dB
More than 70dB (HF)More than 65dB (other bands;
except 1⁄2 IF point on 50MHz, IF point 144MHz band)
More than 2.0W
2-conductor 3.5 (d) mm (1⁄8″)/8Ω
Frequency coverage(Differs according to version)
Modes
Frequency stability
Maximum current drain
Power supply requirement
Antenna connector
Number of memory channels
Dimensions (W×H×D) ; Projections are not included.
Weight (approx.)
Output power
Spurious emissions
Carrier suppression
Unwanted sideband
Microphone connector
Sensitivity (typical)Preamp ONSSB, CW, RTTY, AM: at 10dB S/NFM, WFM: at 12dB SINAD
Selectivity
Spurious and image rejection (except IF)
AF power at 10% distortion with an 8Ω load
External speaker connector
DESKTOP AND PORTABLE TRANSCEIVERS
SPECIFICATIONS
MOBILE TRANSCEIVERS
HANDHELD TRANSCEIVERS
IC-2720HIC-2725E
IC-208HIC-E208 IC-V8000 IC-2200H
IC-T90AIC-E90 IC-T7H IC-T3H
IC-V8
Applicable U.S. Military Specifications
All stated specifications are subject to change without notice or obligation.
*1 Guaranteed range 144–148 and 440–450MHz. Cellular blocked. *2 Guaranteed range 144–146 and 430–440MHz. *3 Guaranteed range 144–148MHz. *4 Guaranteed range 144–146MHz.
*1 Guaranteed range 144–148MHz. *2 Guaranteed range 440–450MHz. *3 Cellular blocked. *4 Guaranteed range 144–146MHz. *5 Guaranteed range 430–440MHz.
Icom makes rugged products that have been tested to and passed the MIL-STD requirements and strict environmental standards for shock (MIL-810C, D, E and F) and vibration (MIL-810C, D, E and F).
IC-T90A (U.S.A.):Tx 50–53.995
144–148430–450*2
Rx 0.495–999.990*3
IC-E90 (Europe): Tx 50–52
144–146430–440
Rx 0.495–999.990
58×87×29mm;29⁄32×37⁄16×15⁄32in
280g; 9.9ozwith antenna and BP-217
5W, 0.5W at 8.0V DC
0.16µV typ.
(50, 144, 430 (440) MHz bands)
IC-P7A (U.S.A.):Tx 144–148
430–450*2
Rx 0.495–999.990*1*2*3
IC-E7 (Europe):Tx 144–146
430–440Rx 0.495–999.990*4*5
47×81×28mm;127⁄32×33⁄16×13⁄32in
160g; 5.6oz with antenna and BP-243
144MHz 1.5W, 0.1W430(440)MHz
1.0W, 0.1Wat 3.7V DC
Less than 0.18µV(144, 430 (440) MHz bands)
U.S.A. VersionTx 144–148
430–450*2
Rx 118–174*1
400–470*2
Europe VersionTx/Rx 144–146
430–440
57×122×29mm;21⁄4×413⁄16×15⁄16inwith BP-173/BP-180
320g; 11.3oz with antenna and BP-180
6.0W, 0.5Wat 13.5V DC
Less than 0.18µV
IC-V8 (U.S.A.): Tx 144–148 Rx 136–174*1
IC-T3H (Europe): Tx/Rx 144–146
54×132×35mm;21⁄8×53⁄16×13⁄8in
350g; 12.3oz with antenna and BP-222N
5.5W, 0.5Wat 7.2V DC
0.16µV typ.
IC-V82IC-U82
IC-V82 (U.S.A.): Tx 144–148 Rx 136–174*1
IC-V82 (Europe): Tx/Rx 144–146
IC-U82 (U.S.A.): Tx 420–450*2
Rx 400–479*2
IC-U82 (Europe): Tx/Rx 430–440
54×139×36.7mm;21⁄8×515⁄32×17⁄16in
390g; 13.8oz with antenna and BP-222N
IC-V82 (at 7.2V DC)7W, 4W, 0.5W
IC-U82 (at 7.2V DC)5W, 2W, 0.5W
0.16µV typ.
Frequency coverage
(Differs according
to version,
Unit: MHz)
Dimensions(W×H×D;
Proj. not included.)
Weight (approx.)
Outputpower
(typical values)
Sensitivity(at 12dB SINAD)
Frequency coverage
(Differs according
to version,
Unit: MHz)
Max. current drain
Dimensions(W×H×D;
Proj. not included.)
Weight (approx.)
Outputpower
(at 13.8V DC;
Differs according
to version)
Sensitivity(at 12dB SINAD)
IC-2720H (U.S.A.):Tx 144–148,
440–450Rx 118–549.995
810–999.990*1
IC-2725E (Europe):Tx/Rx 144–146,
430–440
VHF 12AUHF 11A
Main unit: 140×40×187 mm;51⁄2×19⁄16×73⁄8 in
Controller: 140×50×24.5 mm;51⁄2×131⁄32×31⁄32 in
Main unit: 1.25kg; 2.8lbController:150g; 5.3oz
144MHzHigh: 50WMid.: 15W (approx.)Low: 5W (approx.)
430(440)MHzHigh: 35WMid.: 15W (approx.)Low: 5W (approx.)
Less than 0.18µV(144, 430(440) MHz bands)
1240–1300
7A
Main unit: 141×40×165.8 mm;59⁄16×19⁄16×617⁄32 in
Controller: 150×50×49.5 mm;529⁄32×131⁄32×115⁄16 in
Main unit: 1.2kg; 2.6lbController:220g; 7.7oz
High: 10WLow: 1W (approx.)
DV Less than 0.35µVDD Less than 1.58µVFM Less than 0.18µV(DV, DD = at BER 1%)
IC-208H (U.S.A.):Tx 144–148, 440–450Rx 118–173.995, 230–
549.995, 810– 999.990*1
IC-E208 (Europe):Tx 144–146, 430–440Rx 118–173.995, 230–
549.995, 810–999.990*2
IC-E208 (Europe-1)Tx/Rx 144–146, 430–440
VHF 12AUHF 11.5A
141×40×185.4 mm;59⁄16×19⁄16×75⁄16 in
1.2kg; 2.65lb
144MHzHigh: 55WMid.: 15W (approx.)Low: 5W (approx.)
430(440)MHzHigh: 50WMid.: 15W (approx.)Low: 5W (approx.)
Less than 0.18µV(144, 430(440) MHz bands)
U.S.A. version :Tx 144–148, 440–450Rx 118–173.995,
230–549.995, 810– 999.990*1
VHF 12AUHF 12.5A
141×40×185.4 mm;59⁄16×19⁄16×75⁄16 in
1.2kg; 2.65lb
144MHzHigh: 55WMid.: 15W (approx.)Low: 5W (approx.)
430(440)MHzHigh: 50WMid.: 15W (approx.)Low: 5W (approx.)
DV Less than 0.35µVFM Less than 0.18µV(144, 430(440) MHz bands, DV, DD = at BER 1%)
U.S.A versionTx 144–148Rx 136–174*3
15A
150×50×150 mm;529⁄32×131⁄32×529⁄32 in
1.09kg; 2.2lb
High: 75WMid-Hi: 25W (approx.)Mid-Lo: 10W (approx.)Low: 5W (approx.)
0.15µV typ.
U.S.A. version:Tx 144–148Rx 118–174*3
Europe version:Tx 144–146Rx 118–174*4
Europe-1 version:Tx/Rx 144–146
15A
140×40×196 mm;51⁄2×19⁄16×723⁄32 in
1.25kg; 2.75lb
High: 65WMid-Hi: 25W (approx.)Mid-Lo: 10W (approx.)Low: 5W (approx.)
0.133µV typ.
ID-1 ID-800H
IC-P7AIC-E7
Some models have not been approved by the appropriate authorities in each country. These models may not be sold or leased, or be offered for sale or lease, until approval has been obtained.
!" !# $% !" !# Count on us!
&'
!& () *+,--) .( # /010(0 " $% " #+- -23 303/45 &&6677703 303
83& +9&-:& 1& 0 ; ;<-' = > ? # " !$% # " !#+- =23 03/45 &&6677703 03
(0,0*0 ! # /& 6 > ' 4'8-?& @A8 ! (& - ! " ## $% ! " ## +- -230&0/45 &&66777030&0
/& # 1 1&0 ,?& 8B! 5; /00 " $% " +- =23030/45 &&6677703030
C3 ' - - 4 , 'D3 ' E- , B- 8'% $ 3 " ! ! $% " ! ! +- 323= 303/45 &&6677703= 303
8 &0 ' > 3 E 0 # 1& 8:& '- @-- , 3- 1 #" # ! $% #" # !+- 32303/45 &&667770303
!( 4' +& B(3-' *7 C-' ! #" !$% ! #" +- 9 23030F/45 &&6677703030F
>-7' 8& G!! :7? ;-& ,080 @ , 8' !" #!!$% !" ##+- =233'03/45 &&66777033'03
H -3- '& I& 6'-
#6#J( B.6+E
A3 A30 " A1 # ' A1
3 &=3& 39 ' 3?0
!$ *0 ! 130 8:B 4'B B7 40080 ! " # ##$% ! " # +- -2303/45 &&667770303
8 5: 1-) E *0 H: ;:4' ' ;& 3& ,D: # 8 ! " # #6#6#$% ! " # #+- ID32ID303/45 &&667770ID303
1& D -' " $% " +- 3-23-030-/45 &&6677703-030-
99JS021I © 1997–2005 Icom Inc.