Upload
quantumautomation
View
388
Download
3
Embed Size (px)
Citation preview
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com4
As a leading supplier of terminalblocks for over 17 years, Altech con-tinues to expand the line with themost competitively priced blocks inthe business. Whatever your needsfrom simple wire terminations tosophisticated electronic functions wehave standard and miniature DIN Railmounted terminal blocks to meetthem. Available as individual terminalblocks or in custom-made assem-blies, look to Altech for the followingfunctions, and more.
• Feed-through•Disconnect•High current•Multi-level•Ground• Fuse• Integrated electronics, standardand custom
When you are competing in the globalmarketplace, you need world-classcapabilities. Altech DIN Rail compo-nents put those capabilities at your fin-gertips. Altech’s level of quality meetsor exceeds every national and interna-tional standard for performance andsafety.
DINRAILTERMINAL BLOCKS
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 5
SCREW CLAMP TERMINAL BLOCKAltech terminal blocks feature screw clamps for maximum wiring efficiency and reliability. The blocks are suppliedwith open clamps, ready to accept wires. No special wire preparation or wire lugs are required. Simply strip thewire, insert and tighten the screw to the torque for gas-tight, vibration resistant, solid connections.
The screw clamp design uses a tin-plated, solid copper orsolid brass current bar with grooved serration, a steel cageclamp and screws. As the clamp is tightened, the wire ispressed firmly against the current bar, ensuring positive con-nections every time. The steel parts are zinc plated andchromate passivated for maximum resistance against oxida-tion.
When applying tightening torques, use our straight bladescrewdriver to fit the screw hole guides located in the ter-minal block housings.
THE DIN CONCEPTThe heart of the Altech philosophy is the standardized DIN Rail and snap-on terminal block. The DIN Rail makes possi-ble a compact, organized arrangement of terminal blocks and other DIN Rail mount components. This gives more thanjust the appearance of quality; it saves time and space, enhances design capabilities and provides a centralized con-nect-disconnect area where external and/or internal wiring can be connected quickly and efficiently. At the same time,the DIN concept allows designers to take advantage of constant advances in terminal block technology. Altech DINRail components do more than terminate wires. They distribute power and ground, protect against overloads and per-form a host of other sophisticated functions. Whatever the application: control systems, instrumentation, automa-tion—DIN Rail terminal blocks can help you create it and keep it as up-to-date as tomorrow.
ATEX APPROVEDTERMINAL BLOCKSMany of Altech terminal blocks are AEx eII Ex eII ATEX* approved. They can be used in potentially explosive applications whichmay occur in chemical and petrochemical industry. These terminals can be used in Class 1, Zones 0, 1 and 2 hazardous locations.These terminal blocks comply to EN 500019.The ATEX Directive besides taking into account the electrical sources of explosion, also considering potentially explosive concentrations of gas,vapor or mist along with dust in the air. The ATEX Directive identities two groups of equipment as per EN 50014.
Group 1 where the equipment is intended for use in mining applications.Group 2 where the equipment is intended for all situations other than mines.These groups are further classified into Zones. Zones are areas where there is risk of flammable material being released in the atmosphere.These zones describe the probability of a flammable material being released to atmosphere in explosive concentrations.Zone 0 is the highest risk zone where an explosive atmosphere is expected to exist continuously or for very long periods of time.Zone 1 is an area where an explosive atmosphere is expected to exist for short periods of time, but during a year the accumulation of suchevents is not in excess of 10000 hours.Zone 2 is an area where an explosive concentration of flammable material is not expected and should it be released it will only exist for a veryshort period of time and where the accumulation of events over a year does not exceed much in excess of 10 hours.*CERT #TUV 06 ATEX 2968U
CUSTOM ASSEMBLIESThe beauty of the DIN Rail concept is its convenience; the unsurpassed ease with which many different components and devicescan be mounted on the same rail.
Altech has made things even easier by making it possible for you to order custom designed assemblies with a single part numberor, for that matter, your own drawing number. No need to order amultitude of parts, no more unwanted inventories of bulk-pack-aged accessories.
Send Altech your drawings or specifications, and our experi-enced staff will build, mark and ship your assembly, ready forinstallation. Our on-staff engineers will also assist you in review-ing your drawings.
SPECIFICATIONS
Material Polyamide 6.6Specific Gravity 1.14 - 1.15Upper LimitTemperature 105°C*Lower LimitTemperature - 50°CVolume Resistivity 1012Ω cmSurface Resistivity 1010ΩDielectric Strength 400KV/cmFlammability (UL 94) V2 Grade*
HOUSINGSThe metal parts of Altech terminal blocks are housed in precision-molded, self-extinguishing polyamide 6.6 material for maximumdielectric strength, electrical insulation and temperature resistance. Standard features on all housings include funnel-shaped wireentry openings and screwdriver guides.
SPRING CLAMP CONNECTIONThe spring clamp series terminal blocks offer a time saving alter-native to the popular screw clamp connection.
The pre-stressed spring is opened using a tool (screw driver) so theconductor can be inserted into the insertion space through an open-ing in the spring leg. The conductor is pulled against the current barunder spring force when the tool is removed.
A high contact force is acheived by the design of the spring clampsystem. The design delivers a secure and reliable connection forany application.
Use screwdriverto open spring
Wire islocked in
Wire isinserted
AEx eII Ex eII
* All blocks are availablewith 130°C material,VO grade, on request.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com6
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 7
Red
Grey
Color BlocksGray is the standard color, however a choice of red, yellow, blue, black, white, biege, orange and greenare available. Color blocks are ideal for defining circuits and simplifying wiring.
Yellow Blue Black White Biege Orange Green Dk. Brown
COLOR BLOCKSGray is the standard color, however a choice of red, yellow,blue, black, white, biege, orange and green are available. Colorblocks are ideal for defining circuits and simplifying wiring.
Last, but not least, the indispensable extras. End Stops prevent terminal blocks and other components from sliding laterally on therail. End Plates close off the last terminal in a row of terminals. Isolation Partitions provide visual separation of terminal groups andensure electrical isolation between adjacent terminals of different potentials. A wide selection of insulated and uninsulated fer-rules is offered for your applications and whenever stranded flexible wires must be terminated.
Finally, Altech’s carefully chosen, top-quality tools make wire preparation and connection fast, easy and efficient. Our selectionincludes insulated and uninsulated screwdrivers, wire strippers and hand, power and semi-automatic crimpers.
ACCESSORIESAltech offers a comprehensive array of DIN Rail accessories, carefully crafted to enhance your design capabilities and to put thecrucial finishing touch on your designs.
Internal and External Jumpers are available in standard 2, 3, 4 and 10 pole assemblies for interconnection to distribute potentialswithin terminal block assemblies.
Marking Tags make DIN Rail assemblies easier to wire and facilitate troubleshooting. Altech’s extensive terminal block marking sys-tem includes standard or custom imprinted snap-on tags in a variety of sizes for circuit identification. The Altech marking systemoffers two different versions of marking systems for printing of accessories.
DIN Rails are internationally standardized and available in 35mm, 32mm, and 15mm sizes, with or without perforations.
To help with your selection, the appropriate rail size for each terminal block is listed in the ordering information on each page.Additional selection and ordering information for DIN Rails can be found in the Accessories Section.
CTS2.5U-N CTS4U-NAltech “U” Series Universal RailMounting Standard ScrewClamp Feed through terminalsare the most versatile terminalsfor wire-to-wire connection incontrol, automation, instrumen-tation and power distributionapplications. A special designfeature on the flexible footenables easy mounting and dis-mounting from the DIN Rail withthe help of a screwdriver.
The terminals with AEx eIIEx eII can be used in apotentially explosive atmos-phere which may occur inchemical and petrochemicalindustry.These terminals canbe used in Class 1, Zone 0, 1& 2 hazardous locations.These terminal blocks com-ply to En 500019.
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
Separator Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
5mm
45 x 43mm
9mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross connect.
22-12 AWG 0.5-2.5 sq.mm 22-14 AWG
600V 800V 600V
25A 24A 20A
7 lb-in 0.4 Nm 7 lb-in
Cat. No. Std. Pk.
CTS2.5U-N 50
EP2.5/4UN 50
PP2.5/4UN 50
SP2.5/4UN 100
CA702 50CA802 50
CA721/2 100CA721/3 50CA721/4 50CA721/10 10CA721/100 10
CA741/2 100CA741/3 50CA741/4 50CA741/10 10CA741/100 10
CA703/01 100CA704/01 100CA705/01 100CA731/10 100—CA731/100 10
CA 707/S/Q/01 100
CA717/2 100CA717/3 100CA717/4 100CA717/10 25
MT5 100MT6F 10
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
6 mm
45 x 43 mm
9 mm
Polyamide 6.6
2screwclamps&1tappedholeforcrossconnect.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 800 V 600 V
35/40 A* 32 A 35/40A*
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CTS4U-N 50
EP2.5/4UN 50
PP2.5/4UN 50
SP2.5/4UN 100
CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 10
CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA713/2 100CA713/3 100CA713/4 50CA713/10 25
MT6 100MT6F 10
* 35A with one No. 10 AWG and40A with two No. 12 AWG wires.
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com8
E220514
AEx eIIEx eII
AEx eIIEx eII
Feed-Through
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 9
E220514
CTS16U
12 mm
47 x 43 mm
16 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross connect.
22-6 AWG 2.5-16 sq.mm 20-4 AWG
600 V 800 V 600 V
70 A 76 A 85 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CTS16U 50
SP6/10U 100
CA702 50CA802 50
CA751/2 50CA751/3 50CA751/4 50CA751/10 10
CA761/2 50CA761/3 50CA761/4 50CA761/10 10
CA703/8 100CA704/8 100CA705/8 100CA739/10 100
CA707/S/Q/5 100
MT12 100MT6F 10
CTS6U CTS10U CTS25U
8 mm
47 x 43 mm
12 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross connect.
22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 750 V 600 V
50 A 41 A 50 A
9 lb-in 0.8 Nm 14 lb-in
Cat. No. Std. Pk.
CTS6U 50
EP6/10U 50
PP6/10U 50
SP6/10U 100
CA702 50CA802 50
CA723/2 100CA723/3 50CA723/4 50CA723/10 10
CA743/2 100CA743/3 50CA743/4 50CA743/10 10
CA703/2 100CA704/2 100CA705/2 100CA733/10 100
CA707/S/Q/1 100
CA710/2 100CA710/3 100CA710/4 100CA710/10 25
MT8 100MT6F 10
10 mm
47 x 43 mm
12 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross connect.
22-6 AWG 1.5-10 sq.mm 16-6 AWG
600 V 750 V 600 V
65 A 57 A 65 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CTS10U 50
EP6/10U 50
PP6/10U 50
SP6/10U 100
CA702 50CA802 50
CA724/2 100CA724/3 50CA724/4 50CA724/10 10
CA744/2 100CA744/3 50CA744/4 50CA744/10 10
CA703/3 100CA704/3 100CA705/3 100CA734/10 100
CA707/S/Q/1 100
CA718/2 100CA718/3 50CA718/4 50CA718/10 25
MT10 100MT6F 10
12 mm
56 x 49 mm
18 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross connect.
12-2 AWG 6-25 sq.mm 14-2 AWG
600 V 800 V 600 V
115 A 101 A 115 A
25 lb-in 2.0 Nm 25 lb-in
Cat. No. Std. Pk.
CTS25U 50
EP25U
PP25UN 50
CA702 50CA802 50
CA725/2 50CA725/3 25CA725/4 25CA725/10 10
CA745/2 50CA745/3 25CA745/4 25CA745/10 10
CA703/4 100CA704/4 100CA705/4 100CA735/10 100
CA707/S/Q/2 100
MT12 100MT6F 10
AEx eIIEx eII
AEx eIIEx eII
AEx eIIEx eII
Feed-Through
E220514 E220514 E220514
CTS95U
25 mm
90 x 83 mm
24 mm
Polyamide 6.6
2 screw clamp connections
2-4/0 AWG 25-95 sq.mm 2-4/0 AWG
600V 1000 V 600 V
230 A 232 A 230 A
160 lb-in 18.2 Nm 160 lb-in
Cat. No. Std. Pk.
CTS95U 10
CA202 50CA102 50
MT25 100MT6F 10
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com10
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering info.refer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve& Screw
ExternalJumper
MarkingTags
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
CTS50U
20.5 mm
75.5 x 71 mm
22 mm
Polyamide 6.6
2 screw clamp connections
6-2/0 AWG 16-50 sq.mm 6-2/0 AWG
600V 1000 V 600 V
150 A 150 A 150 A
60 lb-in 6.8 Nm 60 lb-in
Cat. No. Std. Pk.
CTS50U 10
CA202 50CA102 50
MT20 100MT6F 10
CTS35UN
Feed-Through
16 mm
58 x 52.5 mm
18 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross
2-12 AWG 4-35 sq.mm 2-12 AWG
600 V 750 V 600 V
130 A 125 A 130 A
25 lb-in 2.5 Nm 25 lb-in
Cat. No. Std. Pk.
CTS35UN 50
PP35UN 50
CA702 50CA802 50
CA771/2 50CA771/3 25CA771/4 25CA771/10 10
CA781/2 50CA781/3 25CA781/4 25CA781/10 10
CA703/10 100CA704/10 100CA705/10 100CA770/10 100
CA707/S/Q/2 100
MT16 100MT6F 10
CTS35U
15 mm
58 x 52.5 mm
18 mm
Polyamide 6.6
2 screw clamps & 1 tapped hole for cross
8-2 AWG 10-35 sq.mm 8-2 AWG
600 V 750 V 600 V
145 A 125 A 145 A
25 lb-in 2.5 Nm 25 lb-in
Cat. No. Std. Pk.
CTS35U 50
PP35U 50
CA702 50CA802 50
CA726/2 50CA726/3 25CA726/4 25CA726/10 10
CA746/2 50CA746/3 25CA746/4 25CA746/10 10
CA703/5 100CA704/5 100CA705/5 100CA736/10 100
CA707/S/Q/2 100
MT15 100MT6F 10
AEx eIIEx eII
E220514 E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 11
CMC1-2 CMC2-2Connect multiple wires to a singleterminal block and eliminate relia-bility problems encountered whenconnecting two wires into a singleclamp.Two versions are available.
Type CMC1-2 features a singlescrew-cage clamp for 22-10 AWGwires on one side and two clampson the other side for 22-10 AWGwires.
Type CMC2-2 has two identicalclamps for 22-10 AWG wires onboth sides.
6 mm
51.5 x 65 mm
9 mm
Polyamide 6.6
4screwclamps&2tappedholesforcrossconnection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 650 V 600 V
35 A 32 A 35 A
7 lb-in. 0.5 Nm 7 lb-in.
Cat. No. Std. Pk.
CMC2-2 50
EPCMC2-2 50
CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA713/2 100CA713/3 100CA713/4 50CA713/10 25
MT6 100
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Separator Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
6 mm
47 x 46.5 mm
9 mm
Polyamide 6.6
3screwclamps&1tappedholeforcrossconnection
22-10AWG 0.5-4 sq.mm 22-10 AWG
600 V 650 V 600 V
35 A 32 A 35 A
7 lb-in. 0.5 Nm 7 lb-in.
Cat. No. Std. Pk.
CMC1-2 100
EPCMC1-2 50
CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA713/2 100CA713/3 100CA713/4 50CA713/10 25
MT6 100
Feed-Through Multi-Connection
E220514 E220514
CDL4U CDL4U(I.S)Altech double level terminalsare the answer to high wiringdensity problems posed by cer-tain unavoidable wiring arrange-ments. Double level terminalshave the following advantages:
• Double wiring density avail-able without extension ofmounting rails.
• Interconnection/shorting canbe done at both levels.
• Marking/identification bymarking tags possible atboth levels.
CDL4U(I.S) internally shorteddouble level terminals are usefulfor distribution applications byusing shorting links at lower lev-els.
6 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps & 2 tapped holes for cross connection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300V 400 V 600 V
35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U 100
EPCDL4U 50
SPCDL4U 100
CA702 50CA802 50
CA727/2 100CA727/3 50CA727/4 50CA727/10 10
CA747/2 100CA747/3 50CA747/4 50CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 50CA714/10 25
MT2 100
6 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps & 1 tapped hole for cross connection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300 V 400 V 600 V
35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(I.S) 100
EPCDL4U 50
SPCDL4U 100
CA702 50CA802 50
CA727/2 100CA727/3 50CA727/4 50CA727/10 10
CA747/2 100CA747/3 50CA747/4 50CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 50CA714/10 25
MT2 100
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com12
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Separator Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
Marking Tags
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
Feed-Through Double Level
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 13
ODL4UAltech Offset Double LevelTerminals, which provide a sep-arate connection at two levels.In ODL, the top level is offsetfrom the bottom level by halfthe thickness of the terminal.
This offset provides betteraccessibility to the screws onthe lower level.
*It is recommended to use endplates at both ends of assem-bled ODL terminal sets for flatalignment to enable effectiveuse of end stops.
6 mm
63 x 68 mm
9 mm
Polyamide 6.6
4screwclamps&2tappedholesforcrossconnection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 630 V 600 V
35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
ODL4U 50
EPODL4U 50EP1ODL4U 50
CA702 50CA802 50
CA727/2 10CA727/3 10CA727/4 10CA727/10 10
CA747/2 100CA747/3 50CA747/4 50CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 50CA714/10 25
MT6 100
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
FrontBack
Feed-Through Offset Double Level
E220514
CTL2.5U-H CTL2.5U
6 mm
67 x 61 mm
9 mm
Polyamide 6.6
4Screwclamps&3 tappedholes for cross connect.
22-12 AWG 0.5-2.5 sq.mm 22-12 AWG
300 V 500 V 300 V
25 A 24 A 25 A
4.5 lb-in 0.4 Nm 4.5 lb-in
Cat. No. Std. Pk.
CTL2.5U-H 50
EPCTL2.5U-H 50
CA202 50CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
6 mm
67 x 84 mm
9 mm
Polyamide 6.6
6Screwclamps&3 tappedholes for cross connect.
22-12 AWG 0.5-2.5 sq.mm 22-12 AWG
300 V 500 V 300 V
25 A 24 A 25 A
4.5 lb-in 0.4 Nm 4.5 lb-in
Cat. No. Std. Pk.
CTL2.5U 50
EPCTL2.5U 50
CA202 50CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
For applications with extremespace constraints. Only 6mm(.236”) wide, with three sepa-rate feed-through levels.Jumpers can be used toreduce field wiring.
They can also be used in con-trol systems where sensorsand actuator applications areinvolved.
The top level of CTL2.5UH ter-minal block provide connectingpoints for signal while middleand bottom level provide con-necting points are used forpositive and negative poten-tial.
In applications where switch-ing indication is required,choice of CTL2.5UHL andCTL2.5UL terminal blocks withbuilt-in electronic componentsare available.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com14
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags
2 pole3 pole4 pole10 pole100 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
Feed-Through Triple Level
CDLG2.5 CTLG2.5
6 mm
50 x 71 mm
9 mm
Polyamide 6.6
5 Screw clamps & 2 tapped holes for cross connect.
24-12 AWG
300 V
24 A
7 lb-in
Cat. No. Std. Pk. CDLG2.5 50
EPCDLG2.5 50
CA202 50CA702 50CA802 50
CA627/2 100CA627/3 50CA627/4 50CA627/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA611/S/Q 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
6 mm
62 x 87.5 mm
9 mm
Polyamide 6.6
7 Screw clamps & 1 tapped holes for cross connect.
24-12 AWG
300 V
24 A
7 lb-in
Cat. No. Std. Pk. CTLG2.5 50
EPCTLG2.5 50
CA202 50CA702 50CA802 50
CA627/2 100 CA627/3 50 CA627/4 50 CA627/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA611/S/Q 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
The CDLG2.5 is a double leveland the CTLG2.5 is a triplelevel terminal block with anadditional connection point forearthing (Grounding) cables.
This separate connection pointis appropriately identified bythe green-yellow imprint on itstop.
The triple level terminal blockis an ideal choice for motor,sensor, actuator and initiatorconnections.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
Marking Tags
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
Double & Triple
with Ground
Terminal Blocks
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 15
* Add required voltage to part number as suffix;i.e. CTL2.5U(L)/24 for 24V DC
CTL2.5U-H(L)* CTL2.5U(L)*
6 mm
67 x 61 mm
9 mm
Polyamide 6.6
4Screwclamps&2 tappedholes for cross connect.
12V, 24V, 48V, 110V DC
22-12 AWG 0.5-2.5 sq.mm 22-12 AWG
300 V 500 V 300 V
25 A 24 A 25 A
4.5 lb-in 0.4 Nm 4.5 lb-in
Cat. No. Std. Pk.
CTL2.5U-H(L)* 50
EPCTL2.5U-H 50
CA202 50CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
6 mm
67 x 84 mm
9 mm
Polyamide 6.6
6Screwclamps&2 tappedholes for cross connect.
12V, 24V, 48V, 110V DC
22-12 AWG 0.5-2.5 sq.mm 22-12 AWG
300 V 500 V 300 V
25 A 24 A 25 A
4.5 lb-in 0.4 Nm 4.5 lb-in
Cat. No. Std. Pk.
CTL2.5U(L)* 50
EPCTL2.5U 50
CA202 50CA702 50CA802 50
CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA707/S/Q/01 100
CA715/2 100CA715/3 100CA715/4 100CA715/10 50
MT2 100
Ideal for sensor applications.See Altech’s Inductive Proximity Sensor catalog
for ordering information.
E220514 E220514
Feed-Through Triple Level
CGT4N
6 mm
45.4 x 54.2 mm
9 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
7 lb-in 0.8 Nm 7 lb-in
Cat. No. Std. Pk.
CGT4N 50
MT6 100
CGT4UUse ground blocks instead of groundingstuds and wire lugs to terminate groundwires, saving installation and wiring time.
Ground blocks clamp mechanically onto theDIN Rail by tightening the center mountingscrew, making a reliable electrical connec-tion between the cage clamp terminals andthe DIN Rail.The rail serves as a busbar andautomatically distributes ground potentialto all other ground terminals on the samerail.
Ground blocks can also be usedas end stops, preventing other terminalblocks and components from moving later-ally on the DIN Rail.
They are supplied with a standardgreen/yellow housing for easy identificationand accept standard marking tags.
CGT4U, CGT10U and CGT35U can bemounted on both DIN 32mm and DIN35mm rails.
CGT4N, CGT6N and CGT16N can be mount-ed on 35mm DIN rail and have the same topouter profile as the feed through blocks(CTS4U-N, CTS2.5U-N, CTS6U, CTS10U andCTS16U).
• High density• Screw-cage clamp• Special clamping foot• Polyamide 6.6• Color: green/yellow
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Torque
Other Approvals
Terminal Block
DIN Railfor ordering informationrefer to page 70
End Plate
MarkingTags(MTType)
6 mm
48 x 43 mm
9 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CGT4U 50
EPCGT4U 100
MT6 100
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com16
Assembly for single phase3 wire circuits.
AEx eIIEx eII
Ground Blocks
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 17
AEx eII Ex eII
CGT6N
8 mm
47 x 54.5 mm
12 mm
Polyamide 6.6
2 screw clamps
22-8 AWG 1.5-6 sq.mm 22-8 AWG
14 lb-in 0.8 Nm 14 lb-in
Cat. No. Std. Pk. CGT6N 50
MT8 100
E220514
CGT10U
10 mm
50 x 45 mm
12 mm
Polyamide 6.6
2 screw clamps
22-6 AWG 1.5-10 sq.mm 16-8 AWG
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk. CGT10U 50
MT10 100
E220514
AEx eII Ex eII
CGT10N
10 mm
50 x 45 mm
12 mm
Polyamide 6.6
2 screw clamps
22-6 AWG 1.5-10 sq.mm 16-8 AWG
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk. CGT10N 50
MT10 100
CGT16N
12 mm
47 x 43 mm
16 mm
Polyamide 6.6
2 screw clamps
20-4 AWG 2.5-16 sq.mm 20-4 AWG
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk. CGT16N 50
MT10 100
E220514
CGT35U
16 mm
61.5 x 58 mm
18 mm
Polyamide 6.6
2 screw clamps
8-2 AWG 10-35 sq.mm 8.2 AWG
25 lb-in 2.5 Nm 25 lb-in
Cat. No. Std. Pk. CGT35N 20
MT15 100
E220514
Ground Blocks
➀ UL recognition in progress.
➀UL
CSFL4U CSFL4U(L)*Altech fuse terminals are alsoavailable with light indication -CSFL4U(L). A specially designedbuilt-in circuit gives light indica-tion in the event of fuse blow out.Thus, fault in a circuit can be eas-ily located.
However, an application of suchterminals must take into consid-eration residual current flow.
DDFL4U - Double Level FuseTerminal with fuse link on the toplevel has a separate feed throughterminal at the lower level. Thiseliminates use of an additionalfeed through terminal.
In DDFL4U(E), specially designedbuilt in circuit gives light indica-tion in the event of a fuse blowout at the top level. The terminalprovides separate feed throughconnection possibility at thelower level.
DDFL4U(LR): This is a modifiedversion of DDFL4U(E) terminalwhere in two equipotential con-nection points are available onboth ends of the terminal.
Important:The disconnecting device is notsuitable for interrupting load. Thesupply must be switched off beforeoperating the slide link/lever.
† Fuses are sold separatelyAltech, see pages 23-24.
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBar
Shorting Sleeve & Screw
ExternalJumper
Marking Tags (MT Type)(MT Type on Lever)
2 pole3 pole4 pole10 pole
8 mm
43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 22-10 AWG
600 V 600 V
6.3 A 10 A
7 lb-in 7 lb-in
Cat. No. Std.
CSFL4U(L)* 50
EPCSFL4U 50
PPCSFL4U 50
CA702 50 CA802 50
CA711/2 100CA711/3 100CA711/4 50CA711/10 20
MT8 100 MT2 100
8 mm
43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 22-10 AWG
600 V 600 V
6.3 A 10 A
7 lb-in 7 lb-in
Cat. No. Std. Pk.
CSFL4U 100
EPCSFL4U 50
PPCSFL4U 50
CA702 50CA802 50
CA711/2 100CA711/3 100CA711/4 50CA711/10 20
MT8 100MT2 100
* Add required voltage to part numberas a suffix. i.e. CSFL4U(L)/24 for 24V AC/DC.
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
E220514 E220514
† Fuse not included. † Fuse not included.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com18
24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC, 300V AC
Fuse Blocks, 5 x 20 and 5 x 25 mm
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 19
CSFL6U
8 mm
60 x 43 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25 mm
22-8 AWG 1.5-6 sq.mm 22-8 AWG
300 V 500 V 300 V
10 A 6.3 A 10 A
14 lb-in 0.8 Nm 14 lb-in
Cat. No. Std. Pk.
CSFL6U 50
EPCSFL6U 50
CA702 50CA802 50
CA710/2 100CA710/3 100CA710/4 100CA710/10 25
MT8 100MT6 100
E220514
† Fuse not included.
8 mm
66 x 88 mm
9.5 mm
Polyamide 6.6
4 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
DDFL4U(E)* 20
EPDDFL4U 20
CA702 50CA802 50
CA729/2 100CA729/3 50CA729/4 50CA729/10 10
CA749/2 100CA749/3 50CA749/4 50CA749/10 10
CA703/6 100CA704/6 100CA705/6 100CA737/10 100
CA707/S/Q/3 100
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC
8 mm
66 x 88 mm
9.5 mm
Polyamide 6.6
4 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
DDFL4U 20
EPDDFL4U 20
CA702 50CA802 50
CA729/2 100CA729/3 50CA729/4 50CA729/10 10
CA749/2 100CA749/3 50CA749/4 50CA749/10 10
CA703/6 100CA704/6 100CA705/6 100CA737/10 100
CA707/S/Q/3 100
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
DDFL4U DDFL4U(E)*
E220514 E220514
† Fuse not included. † Fuse not included.
8 mm
66 x 88 mm
9.5 mm
Polyamide 6.6
4 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
DDFL4ULR 20
EPDDFL4U 20
CA702 50CA802 50CA202 50
CA730/2 100CA730/3 50CA730/4 50CA730/10 10
CA740/2 100CA740/3 50CA740/4 50CA740/10 10
CA703/7 100CA704/7 100CA705/7 100CA738/10 100
CA707/S/Q/8 100
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
DDFL4ULR
E220514
† Fuse not included.
Fuse Blocks, 5 x 20 and 5 x 25 mm
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBar
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
Top LevelBottom Level
DDFL4U(LR): This is a modifiedversion of DDFL4U(E) terminalwhere in two equipotential con-nection points are available onboth ends of the terminal.
CAFL4U(L) is equipped with aLED for blown fuse indication.CAFL4U(N) is equipped with aneon bulb for same application.
Important:The disconnecting device is notsuitable for interrupting load. Thesupply must be switched offbefore operating the slidelink/lever.
† Fuses are sold separatelyAltech, see pages 23-24.
* Add required voltage to partnumber as suffix, i.e.DDFL4U(E)/24 for 24V AC/DC
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com20
8 mm
66 x 88 mm
9.5 mm
Polyamide 6.6
4 screw clamps
Ø5x20, Ø5x25 mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
DDFL4U(E)LR* 20
EPDDFL4U 20
CA702 50CA802 50CA202 50
CA730/2 100CA730/3 50CA730/4 50CA730/10 10
CA740/2 100CA740/3 50CA740/4 50CA740/10 10
CA703/7 100CA704/7 100CA705/7 100CA738/10 100
CA707/S/Q/8 100
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC
DDFL4U(E)LR*
E220514
† Fuse not included.
Fuse Blocks, 5 x 20 and 5 x 25 mm
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 21
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBar
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
Top LevelBottom Level
CAFL4U
9 mm
50 x 72 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø1/4x1 in., Ø1/4x11/4 in.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
16 A 6.3 A 16 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CAFL4U 25
EPCAFL4U 50
CA702 50CA802 50
CA716/2 50CA716/3 50CA716/4 50CA716/10 25
MT9 100
CAFL4U(L)* CAFL4U(N)
9 mm
50 x 72 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø1/4x1 in., Ø1/4x11/4 in.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
16 A 6.3 A 16 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CAFL4U(L)* 25
EPCAFL4U 50
CA702 50CA802 50
CA716/2 100CA716/3 50CA716/4 50CA716/10 20
MT9 100
9 mm
50 x 72 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø1/4x1 in., Ø1/4x11/4 in.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
16 A 6.3 A 16 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CAFL4U(N) 25
EPCAFL4U 50
CA702 50CA802 50
CA716/2 100CA716/3 50CA716/4 50CA716/10 20
MT9 100
24VAC/DC,48VAC/DC,110VAC/DC, 220VAC,300VAC
110-220VAC/DC,300VAC
E220514 E220514 E220514
† Fuse not included. † Fuse not included. † Fuse not included.
Fuse Blocks, 1/4 x 1 and 1/4 x 11/4 in.
1 POLE 2 POLE 3 POLEThe main characteristics offuse disconnectors are:
• Compliance with IEC60947-1, IEC 60947-3
• UL508 recognized• Plastic parts are made ofmaterial resistant to hightemperatures
• All contact surfaces aresilver plated
• Mounting on standard DIN35 mm rail (DIN EN60715).
• Available up to 4 pole• For all sizes a version withelectronic indicator isavailable. There are twotechnical types of indicator:
L (LED) with built in LEDdiode which blinks after thefuse-link operates. The inter-nal circuit resistance is 2M,thus the total dissipation isminimal. The indicator iscapable of operating in con-ditions of open circuit withminimum capacitance be-tween connection cables.Operating voltage rangespans from 50V to 690V ACand DC.
I (NEON) with neon lamp,which is constantly lit afterthe fuse-link operates. Theinternal circuit resistance is570k, thus it is necessary thatthe circuit be closed in orderfor the indicator to function.The operational voltagerange is 100 V to 750 V AC.
* Fuses are sold separatelyAltech, see pages 23-24.
79 mm (3.11 in.)64.5 mm (2.54 in.)
47.5 mm (1.87 in.)4 mm (0.16 in.)
B
81m
m(3
.19
in.)
37 mm (1.46 in.) Dimension for B:1 Pole 17.5mm1 Pole + Neutral 35mm2 Pole 35mm3 Pole 52.5mm3 Pole + Neutral 70mm
17.5 mm
77 x 63.5 mm
11 mm
Aculon ®
2 screw clamps
Ø10 x 38 mm
24-4 AWG 1.5-25sq.mm 24-4 AWG
690 V 400 V** 690 V
32A 32A** 32A
31 lb-in 2-2.5 Nm 31 lb-in
Cat. No. Std. Pk.
CB1038-1 1CB1038-1/L 1CB1038-1/I 1
CA702 50CA802 50
TerminalWidth (B)
Height x Length
Stripping Length
Insulation Material
Type of Connection
Fusion Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Terminal BlockIndicator:NoneLEDNeon
DIN Railfor ordering informa-tionrefer to page 70
End Stopfor ordering informationrefer to page 72
E212627
35 mm
77 x 63.5 mm
11 mm
Aculon ®
2 screw clamps
Ø10 x 38 mm
24-4 AWG 1.5-25sq.mm 24-4 AWG
690 V 400 V** 690 V
32A 32A** 32A
31 lb-in 2-2.5 Nm 31 lb-in
Cat. No. Std. Pk.
CB1038-2 1CB1038-1/L 1CB1038-2/I 1
CA702 50CA802 50
E212627
52.5 mm
77 x 63.5 mm
11 mm
Aculon ®
2 screw clamps
Ø10 x 38 mm
24-4 AWG 1.5-25sq.mm 24-4 AWG
690 V 400 V** 690 V
32A 32A** 32A
31 lb-in 2-2.5 Nm 31 lb-in
Cat. No. Std. Pk.
CB1038-3 1CB1038-3/L 1CB1038-3/I 1
CA702 50CA802 50
E212627
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com22
Fuse Blocks, 10 x 38 mm
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 23
38 mm(1.5 in.)
Ø10.3 mm(0.4 in.)
6 mm(0.24 in.)
6 mm(0.24 in.)
10.5 mm(0.4 in.)
10.5 mm(0.4 in.)
10x38
Operating PowerIn Cat. No. I2-value Dissipation Std. Pk.(A) (A’s) (W)
1 2645126 1.6 1 102 2645127 8 1.8 104 2645128 8 1.1 106 2645129 25 1.6 108 2645130 39 1.8 10
10 2645131 66 2.1 1012 2645132 87 3.1 1016 2645133 166 4.4 1020 2645134 280 5.8 1025 2645135 580 6.8 1030 2645136 1.010 8.2 10
10x38
10x38
10x38
6 2625005 30 1.5 108 2625006 50 2 10
10 2625007 70 2.5 1012 2625008 120 3 1016 2625009 150 3.5 1020 2625011 260 4.8 1025 2625013 290 6 1032 2625015 600 7.5 10
** 6-25A (700V DC/ breaking capacity ––--- 50kA)32A (400V DC/ breaking capacity ––--- 50kA)
Operating PowerIn Cat. No. I2-value Dissipation Std. Pk.(A) (A’s) (W)
Rated Current/RatedVoltate Cat. No. Std. Pk.
0.5A 2620017 101A 2620000 102A 2620001 104A 2620003 106A 2620005 108A 2620006 1010A 2620007 1012A 2620008 1016A 2620009 1020A 2620011 1025A 2620013 1032A* 2620015 10
*400V
Rated Current/RatedVoltate Cat. No. Std. Pk.
0.5A 2621017 101A 2621000 102A 2621001 104A 2621003 106A 2621005 108A 2621006 1010A 2621007 1012A 2621008 1016A 2621009 1020A 2621011 1025A 2621013 1032A* 2621015 10
*400V
Cylinder Fuses are typically used inindustrial applications to protect electri-cal devices such as motors, drives, etc.
They are available in four sizes with acurrent range from 1 to 125 Amps.Cylinder Fuses have metal caps at bothends, and a porcelain fuse body.
OPERATING CLASSES
gL/gG - Line ProtectionSlow, typically used for distribution cir-cuits or resistive loads.
Typical Markings: gL/gG
aM - Motor ProtectionFast acting short circuit protection,but slow acting overload protection.
Typical Marking: aM
aR - Semiconductor Protection
Partial range, short circuit protectionfor devices such as diodes, SCRs. etc.
Typical Markings: Ultra Rapid™,Sitor™, Silcu™, Protister™, Recticur™,Ultra Quick™, aR
gR - Semiconductor Protection
Full range, short circuit protection fordevices such as diodes, SCRs. etc.
Typical Markings: Ultra Rapid™,Sitor™, Silcu™, Protister™, Recticur™,Ultra Quick™, gR
Note:Other fuse sizes and fuse holdersare available. Please refer to theAltech European Fuse catalog formore information.
gL/gG - Line ProtectionStandard: IEC 20269-4-1and IEC60269-1
Rated Voltage: 500V
aM - Motor ProtectionStandard: IEC 20269-4-1and IEC60269-1
Rated Voltage: 500V
aR - Semiconductor ProtectionStandard: IEC 60269-4-1Breaking Capacity: ~200 kARated Voltage: ~600V**
gR - Semiconductor ProtectionStandard: IEC 60269-4-1Breaking Capacity: ~200 kARated Voltage: ~690V
Certified for 700V
Fuses
Voltage 250V AC/DCDIN 41662 DIN 41571-2 DIN 41661IEC-127-2/III IEC-127-2/II
Cat. No.Slow Medium Fast
0.02M5x20M0.032M5x20M
0.05M5x20T4 0.05M5x20M 0.05M5x20F4
0.063M5x20M0.08M5x20T4 0.08M5x20M0.1M5x20T4 0.1M5x20M 0.1M5x20F4
0.125M5x20T4 0.125M5x20M 0.125M5x20F4
0.16M5x20T4 0.16M5x20M 0.16M5x20F4
0.2M5x20T4 0.2M5x20M 0.2M5x20F4
0.25M5x20T4 0.25M5x20M 0.25M5x20F4
0.315M5x20T4 0.315M5x20M 0.315M5x20F4
0.4M5x20T4 0.4M5x20M 0.4M5x20F4
0.5M5x20T4 0.5M5x20M 0.5M5x20F4
0.63M5x20T4 0.63M5x20M 0.63M5x20F4
0.7M5x20T4 0.7M5x20M 0.7M5x20F4
0.8M5x20T4 0.8M5x20M 0.8M5x20F4
1.0M5x20T4 1.0M5x20M 1.0M5x20F4
1.25M5x20T4 1.25M5x20M 1.25M5x20F4
1.4M5x20T4 1.4M5x20M1.6M5x20T4 1.6M5x20M 1.6M5x20F4
2.0M5x20T4 2.0M5x20M 2.0M5x20F4
2.5M5x20T4 2.5M5x20M 2.5M5x20F4
3.15M5x20T4 3.15M5x20M 3.15M5x20F4
4.0M5x20T4 4.0M5x20M 4.0M5x20F4
5.0M5x20T4 5.0M5x20M 5.0M5x20F4
6.3M5x20T4 6.3M5x20M 6.3M5x20F4
8.0M5x20T1 8.0M5x20M 8.0M5x20F1
10.0M5x20T1 10.0M5x20M 10.0M5x20F1
12.5M5x20T1 12.5M5x20M1 12.5M5x20F1
16.0M5x20T1 16.0M5x20M1 16.0M5x20F1
20.0M5x20T1 20.0M5x20M1 20.0M5x20F1
Std. Pk. 10
Voltage 250V AC/DC
Cat. No.Slow Fast
0.032M6.3x32T0.04M6.3x32T0.05M6.3x32T4 0.05M6.3x32F0.063M6.3x32T4 0.063M6.3x32F0.08M6.3x32T4 0.08M6.3x32F0.1M6.3x32T4 0.1M6.3x32F0.125M6.3x32T4 0.125M6.3x32F0.16M6.3x32T4 0.16M6.3x32F0.2M6.3x32T4 0.2M6.3x32F0.25M6.3x32T4 0.25M6.3x32F0.315M6.3x32T4 0.315M6.3x32F
0.4M6.3x32T4 0.4M6.3x32F0.5M6.3x32T4 0.5M6.3x32F0.63M6.3x32T4 0.63M6.3x32F0.7M6.3x32T4 0.7M6.3x32F0.8M6.3x32T4 0.8M6.3x32F1.0M6.3x32T4 1.0M6.3x32F4
1.25M6.3x32T4 1.25M6.3x32F4
1.6M6.3x32T4 1.6M6.3x32F4
2.0M6.3x32T4 2.0M6.3x32F4
2.5M6.3x32T4 2.5M6.3x32F2,4
3.15M6.3x32T4 3.15M6.3x32F2,4
4.0M6.3x32T4 4.0M6.3x32F2,4
5.0M6.3x32T4 5.0M6.3x32F3,4
6.3M6.3x32T4 6.3M6.3x32F3,4
7.0M6.3x32T4 7.0M6.3x32F3
8.0M6.3x32T4 8.0M6.3x32F3
10.0M6.3x32T4 10.0M6.3x32F3
12.5M6.3x32T4 12.5M6.3x32F3
16.0M6.3x32T4 16.0M6.3x32F3
20.0M6.3x32T4 20.0M6.3x32F3
Std. Pk. 10
Voltage 250V AC/DCDIN 41571-2
Cat. No.Medium
0.032M5x25M0.04M5x25M0.05M5x25M0.063M5x25M0.08M5x25M0.1M5x25M0.125M5x25M0.16M5x25M0.2M5x25M0.25M5x25M0.315M5x25M
0.4M5x25M0.5M5x25M0.63M5x25M0.8M5x25M
1.0M5x25M1.25M5x25M1.6M5x25M
2.0M5x25M2.5M5x25M
3.15M5x25M4.0M5x25M5.0M5x25M6.3M5x25M
8.0M5x25M1
10.0M5x25M1
16.0M5x25M1
Std. Pk. 10
Miniature Fuses are typicallyused to protect electronicdevices, laboratory and meas-urement instruments, stereos,TV’s,VCR’s etc.They are availablein four sizes with a current rangeof 20mA to 20 Amps. MiniatureFuses are manufactured accord-ing to VDE 0820 part 1, VDE 0820part 2, IEC publication 127, CEEpublication 4 and actual DINstandards.
The 5x20, 5x25 fuses can be usedin the CSFL4U series terminalblocks. The 6.3x32 fuse can beused in the CAFL4U series termi-nal blocks.
Operating Class:Slow,Typical Marking: “T”Medium,Typical Marking: “M”Fast,Typical Marking: “F”
1 Not standard rating.2 Rated Voltage 150V.3 Rated Voltage 60V.4 UL recognized version
available upon request.
5 X 20 5 X 25 6.3 X 32 (1/4” X 1-1/4”)
Current
20mA32mA40mA50mA63mA80mA
100mA125mA160mA200mA250mA315mA
400mA500mA630mA700mA800mA
1.0A1.25A1.4A1.6A2.0A2.5A
3.15A4.0A5.0A6.3A7.0A8.0A
10.0A12.5A16.0A20.0A
upon request upon request
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com24
Miniature Fuses
Altech’s increasingly popular industrialenclosures keep you well covered with theirhigh quality and attractive design.
All at Very Competitive Prices!And many available for immediate delivery.
Customization available!
Illustrated are just a few of the applications for our enclosures.
Rustproof• Polycarbonate/Polystyrene enclosures will
last indefinitely without corrosionVisibility
• Components and devices are fully visiblethrough transparent covers, whilecompletely protected and insulated
Impact Resistant• Non-metallic enclosures
withstand bumps andblows, they will not dent
Maintenance Free• Surface finish does not
deteriorate and requiresno special painting orrefinishing
Chemical resistant• Resist weak and
strong acids andalkali
Lightweight• Non-metallic
enclosures weighsignificantly less thanmetal, simplifyinghandling
Flexibility• Enclosures can be
easily customized
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 25
CDTTU CDTTU-SH
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBar
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
2 pole3 pole4 pole10 pole
8 mm
57 x 63 mm
12 mm
Polyamide 6.6
2 screw clamps
16-8 AWG 1.5-6 sq.mm 16-8 AWG
600 V 800 V 600 V
41 A 41 A 41 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CDTTU 50
EPCDTTU 50
CA702 50CA802 50
CA710/2 100CA710/3 100CA710/4 100CA710/10 25
MT8 100
Disconnect and test terminals arean ideal choice for measuringcontrol and regulatory circuits.The terminals provide a clearfunctional advantage for deviceshaving utility instruments andassociated transformers.
Five versions of disconnect andtest terminals are available:
• CDTTU - disconnection isachieved by means of a slidelink operated with a screw driver.
• CDTTU-SH - disconnect and testterminals are ideal for use incurrent transformer applicationswhen it is mandatory to keep thesecondary side shorted at anypoint while taking currentmeasurements.
• CKT4U - disconnection isachieved by lifting theknife contact lever.
• CSDL4U - hinged disconnectionand testing terminal,incorporates a connecting link inplace of the fuse link.
• CSDL6U - hinged disconnectblock for 8 AWG size wires.
• DDDL4U - double leveldisconnect terminal with hingeddisconnect in upper level.
Specially designed socket headscrews act as test/monitoringpoints in both CDTTU, CDTTU-SHand CKT4U.
Important: The disconnectingdevice is not suitable for interrupt-ing load. The supply must beswitched off before operating theslide link/lever.
16 mm
57 x 63 mm
12 mm
Polyamide 6.6
4 screw clamps
16-8 AWG 1.5-6 sq.mm 16-8 AWG
300 V 300 V 300 V
10 A 10 A 10 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CDTTU-SH 50
EPCDTTU 50
CA702 50CA802 50
CA710/2 100CA710/3 100CA710/4 100CA710/10 25
MT8 100
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com26
Disconnect
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 27
CKT4U CSDL4U DDDL4U
8 mm
43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
14 A 6.3 A 14 A
7 lb-in 0.8 Nm 7 lb-in
Cat. No. Std. Pk.
CSDL4U 100
EPCSFL4U 50
PPCSFL4U 50
CA702 50CA802 50
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
8 mm
66 x 88 mm
9.5 mm
Polyamide 6.6
4 screw clamps
22-10 AWG 22-10 AWG
300 V 300 V
14 / 35 A 14 / 35 A
7 lb-in 7 lb-in
Cat. No. Std. Pk.
DDDL4U 20
EPDDFL4U 20
CA702 50CA802 50
CA729/2 100CA729/3 50CA729/4 50CA729/10 10
CA749/2 100CA749/3 50CA749/4 50CA749/10 10
CA703/6 100CA704/6 100CA705/6 100CA737/10 100
CA707/S/Q/3 100
CA711/2 100CA711/3 100CA711/4 50CA711/10 25
MT8 100MT2 100
6 mm
46 x 46.3 mm
9 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 800 V 600 V
16 A 16 A 16 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CKT4U 50
EPCKT4U 50
CA702 50CA802 50
CA713/2 100CA713/3 100CA713/4 50CA713/10 25
MT6 100
CSDL6U
8 mm
60 x 43 mm
9.5 mm
Polyamide 6.6
2 screw clamps
22-8 AWG 1.5-6 sq.mm 22-8 AWG
300 V 500 V 300 V
10 A 6.3 A 10 A
14 lb-in 0.8 Nm 14 lb-in
Cat. No. Std. Pk.
CSDL6U 50
EPCSFL6U 50
CA702 50CA802 50
CA710/2 100CA710/3 50CA710/4 50CA710/10 25
MT8 100
E220514 E220514 E220514
Disconnect
CDB4/x CDB4/x(1)Altech CDB Compact Distribu-tion Blocks are an ideal choicefor a simplified distribution sys-tem. A lug/bolt secures theincoming cable and the screwclamp design of the block pro-vides the outgoing connec-tions. These provide easy con-nect points and ensure perfectcontinuity for distribution. Aprotective shield effectivelyshrouds the incoming connec-tion.
Application Information:Sum of outgoing currents oneither side of center should notexceed half the maximum per-missible incoming current.
Sum of total outgoing currentsshould not exceed maximumpermissible incoming current.
Connection for higher outgoingcurrents should be donethrough the terminal nearest tothe incoming connection.
TerminalWidth
Height &Width
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
MarkingTags (MTType)
Warning Label
6 mm
45 x 43 mm
9 mm
Polyamide 6.6
10-8 AWG 6-16 sq.mm 10-8 AWG22-12 AWG 0.5-4 sq.mm 22-10 AWG
600 V 800 V 600 V
50 A 50 A25 A 32 A 35 A
26 lb-in 2.0 Nm 26 lb-in7 lb-in 0.5 Nm 7 lb-in
Cat.No. HxWxL (mm) Outputs Std.Pk.
CDB4/1 45 x 43 x 43.8 4 10CDB4/2 45 x 43 x 55.8 8 10CDB4/3 45 x 43 x 67.8 12 10CDB4/4 45 x 43 x 80 16 5CDB4/5 45 x 43 x 96 20 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT6 100
InputOutput
InputMax. Individual Output
InputOutput
1 Lug/ M5 bolt connection for ring lugScrew clamp connection
InputOutput
6 mm
45 x 43 mm
9 mm
Polyamide 6.6
10-8 AWG 6-16 sq.mm 10-8 AWG22-12 AWG 0.5-4 sq.mm 22-10 AWG
600 V 800 V 600 V
50 A 50 A25 A 32 A 35 A
26 lb-in 2.0 Nm 26 lb-in7 lb-in 0.5 Nm 7 lb-in
Cat.No. HxWxL (mm) Outputs Std.Pk
CDB4/2(1) 45 x 43 x 52 4 10CDB4/3(1) 45 x 43 x 58 6 10CDB4/4(1) 45 x 43 x 64 8 5CDB4/5(1) 45 x 43 x 70 10 5CDB4/6(1) 45 x 43 x 76 12 5CDB4/10(1)45 x 43 x 100 20 5CDB4/11(1)45 x 43 x 106 22 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT6 100
1 Lug M5 /bolt connection for ring lugScrew clamp connection
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com28
Distribution Block
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 29
CDB25/x
12 mm
56 x 49 mm
18 mm
Polyamide 6.6
6-2/0 AWG 10-50 sq.mm 6-2/0 AWG12-2 AWG 6-25 sq.mm 12-2 AWG
600 V 800 V 600 V
150 A 150 A75 A 101 A 75 A
53 lb-in 6.0 Nm 53 lb-in14 lb-in 2 Nm 14 lb-in
Cat. No. H x W x L (mm) Outputs Std.Pk
CDB25/2 56 x 49 x 88 8 10CDB25/3 56 x 49 x 112 12 10CDB25/4 56 x 49 x 136 16 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT12 100
CDB6/x CDB10/x
8 mm
43 x 47 mm
12 mm
Polyamide 6.6
10-2 AWG 6-25 sq.mm 10-2 AWG22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 800 V 600 V
100 A 100 A50 A 41 A 50 A
25 lb-in 3.0 Nm 35 lb-in9 lb-in 0.8 Nm 14 lb-in
Cat. No. H x W x L (mm) Outputs Std.Pk
CDB6/2 43 x 47 x 64 8 10CDB6/3 43 x 47 x 80 12 10CDB6/4 43 x 47 x 96 16 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT8 100
SWL6 100
1 Lug/ M6 bolt connection for ring lugScrew clamp connection
10 mm
43 x 47 mm
12 mm
Polyamide 6.6
8-1/0 AWG 10-35 sq.mm 8-1/0 AWG22-6 AWG 1.5-10 sq.mm 22-6 AWG
600 V 800 V 600 V
125 A 130 A65 A 57 A 65 A
53 lb-in 6.0 Nm 53 lb-in14 lb-in 1.2 Nm 14 lb-in
Cat. No. H x W x L (mm) Outputs Std.Pk
CDB10/2 43 x 47 x 72 8 10CDB10/3 43 x 47 x 92 12 10CDB10/4 43 x 47 x 112 16 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT10 100
1 Lug/ M8 bolt connection for ring lugScrew clamp connection
1 Lug/ M8 bolt connection for ring lugScrew clamp connection
E220514 E220514 E220514
Distribution Block
Terminal Width
Height & Width
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Marking Tags (MT Type)
Warning Label
InputOutput
InputMax. Individual Output
InputOutput
InputOutput
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com30
CMDB4/X
6 mm
45 x 43 mm
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 800 V 600 V
30 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. H x W x L Outputs Std.(mm) Pk.
CMDB4/2 45 x 43 x 13.5 4 10CMDB4/3 45 x 43 x 19.5 6 10CMDB4/4 45 x 43 x 25.5 8 5CMDB4/10 45 x 43 x 61.5 20 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT6 100
Screw clamp connection
CMDB10/X
10 mm
43 x 47 mm
12 mm
Polyamide 6.6
22-6 AWG 1.5-10 sq.mm 20-6 AWG
600 V 800 V 600 V
65 A 57 A 65 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. H x W x L Outputs Std.(mm) Pk.
CMDB10/2 43 x 48 x 21.5 4 10CMDB10/3 43 x 48 x 31.5 6 10CMDB10/4 43 x 48 x 41.5 8 10CMDB10/10 43 x 48 x 101.5 20 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT10 100
Screw clamp connection
CMDB6/X
8 mm
43 x 47 mm
12 mm
Polyamide 6.6
22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 800 V 600 V
50 A 41 A 50 A
9 lb-in 0.8 Nm 14 lb-in
Cat. No. H x W x L Outputs Std.(mm) Pk.
CMDB6/2 43 x 48 x 17.5 4 10CMDB6/3 43 x 48 x 25.5 6 10CMDB6/4 43 x 48 x 33.5 8 10CMDB6/10 43 x 48 x 81.5 20 5
Cat. No. Std. Pk.
CA702 50CA802 50
MT8 100
SWL6 100
Screw clamp connection
CMDB blocks are the modifiedversion of CDB terminal blockswithout central incoming ter-minal connections.
Distribution Block
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 31
CONNECTOR TO TERMINALBLOCK MODULESCompact and reliable connections betweenhigh density connectors and high qualityscrew-cage clamp terminal blocks; DIN Railmountable
PLUGGABLESLIMLINE RELAYSNeed Text
DIODE MODULES &COMPONENT CARRIERSAdd additional components to build circuitsand diode modules mounted on 35 or32mm DIN Rails.
MONITORING PROTECTIONMODULESSpecial purpose components connected toscrew-cage clamp terminal blocks; DIN Railmountable.
POWER SUPPLIESBasic and High Performance Series. DINRail mountable units are available with 12or 24VDC output, 15 to 60 Watts and reg-ulated outputs.
SOLID STATE I/O MODULESInput/Output Modules (both AC and DC)provided on a DIN mountable module.Bussed and isolated versions available.
RELAY MODULESTraditional relay modules from 1-16 chan-nels. Available in several voltages (AC &DC), isolated or bussed systems. DIN Railmounted.
SAFETY RELAY MODULESForce-guided contact modules available in1-16 channels, 12 and 24VDC coils andisolated or bussed systems. All mountableon 32 or 35mm DIN Rails.
CUSTOM MODULESAltech provides quick turn-key customdesigns and competitive solutions.
GENERAL PURPOSE/INTERFACE RELAYSA selection of DIN Rail mountable generalpurpose relays available for up to 12 A @250 Volts.
MOUNTING TRACKSDIN Rail or panel mount mounting trackssecure standard or custom printed circuitboards in control panels or cabinets.
I/O MODULE CARRIERSAccepts industry standard I/O modules.LED indicator and fuse protection includedon carrier.
We have a full line of standard and customInterface Modules and Power Supplies.
Contact AltechToday to learn more!
Part Number:
Approvals
Current Rating
Voltage Rating
SCCR
No. of InputsWire RangeTorque
ScrewTypeNo. of Outputs
Wire RangeTorqueWire RangeTorque
ScrewTypeOptionalMarkingTag**(for DB16and DB35)
Dimensions:
DB16*
80A 80A
600V AC 690V AC
10kA
1 18-4 AWG 6-16mm2
13.5lb.-in. 1.5Nm
Pozi Drive 26 6
(2x)8-4 AWG (2x)6-16mm2
13.5lb.-in. 1.5Nm(4x)14-10 AWG (4x)2.5-6mm2
7.2lb.-in. 0.8NmPozi Drive 2
MT2**
38049
80A 80A
600V AC 690V AC
100kA
1 18-4 AWG 6-16mm2
13.5lb.-in. 1.5Nm
Pozi Drive 26 6
(2x)8-4 AWG (2x)6-16mm2
13.5lb.-in. 1.5Nm(4x)14-10 AWG (4x)2.5-6mm2
7.2lb.-in. 0.8NmPozi Drive 2
DB35*
115A 125A
600V AC 690V AC
10kA
1 18-2 AWG 10-35mm2
31lb.-in. 3.5Nm
Pozi Drive 26 6
14-6 AWG 2.5-16mm2
17.5lb.-in. 2Nm
Pozi Drive 2
MT2**
38041
115A 125A
600V AC 690V AC
100kA
1 18-2 AWG 10-35mm2
13.5lb.-in. 3.5Nm
Pozi Drive 26 6
14-6 AWG 2.5-16mm2
17.5lb.-in. 2Nm
Pozi Drive 2
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com32
DB16• Quick mountingand wiring
• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DINRail mountable modulardevices (height 95mm,depth 44.5mm)
• Accessories increase thenumber of outputs withonly one input (appliesonly to 38041 and 38032)
• No caps to open / remove• Material
Housing: PolyamideMetal Body: Brass
Fork Type Busbar38045
38041
UL File E220514 UL File E98082 UL File E220514 UL File E98082
Accessories: ForkType BusbarPart No: 38045 to jump 2 Blocks
38046 to jump 8 Blockscan be cut
38041
38049 DB35 38041
One Phase Power Distribution Block
* Available in colors. Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 33
43 mm(1.69 in)
38.5 mm(1.52 in)
45 mm(1.77 in)
58m
m(2
.28
in)
5.2 mm(0.20 in)
17.4 mm(0.69 in)
13.8 mm(0.54 in)
19.9 mm(0.78 in)
5.2 mm(0.20 in)
71m
m(2
.80
in)
43 mm(1.69 in)
38.5 mm(1.52 in)
45 mm(1.77 in)
58m
m(2
.28
in)
5.2 mm(0.20 in)
17.4 mm(0.69 in)
13.8 mm(0.54 in)
19.9 mm(0.78 in)
5.2 mm(0.20 in)
71m
m(2
.80
in)
38032
38032
160A 160A
600V AC 690V AC
100kA
1 18-2/0AWG 10-70mm2
35.5lb.-in. 4NmHex 5
6 614-6 AWG 2.5-16mm2
17.5lb.-in. 2NmHex 3
38076
Part Number:
Approvals
Current Rating
Voltage Rating
SCCR
No. of InputsWire RangeTorque
ScrewTypeNo. of Outputs
Wire RangeTorque
ScrewType
Dimensions:
38076
115A 125A
600V AC 690V AC
100kA
1 18-2 AWG 10-35mm2
53lb.-in. 6NmHex 4
10 1014-4 AWG 2.5-16mm2
26.5lb.-in. 3NmHex 3
38074
38074
175A 175A
600V AC 690V AC
100kA
1 16-2/0AWG 16-70mm2
53lb.-in. 6NmHex 5
10 1014-4 AWG 2.5-16mm2
26.5lb.-in. 3NmHex 3
Copper Jumper Bar3803221
38032
UL File E98082 UL File E98082 UL File E98082
Accessories: Copper Jumper Bar(6x15 mm)
Part No: 3803221 for 2 Blocks3803231 for 3 Blocks3803241 for 4 Blockscan be cut
38032
One Phase Power Distribution Block
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com34
38020 38019
Part Number:
Approvals
Current Rating
Voltage Rating
SCCR
No. of InputsWire RangeTorque
ScrewTypeNo. of Outputs
Wire RangeTorqueWire RangeTorqueWire RangeTorque
ScrewType
Dimensions:
38020 38019
230A 250A 310A 400A
600V AC 690V AC 600V AC 690V AC
100kA 100kA
1 1 1 12-4/0AWG 35-120mm2 3/0-350mcm 95-185mm2
170lb.-in. 19Nm 230lb.-in. 25NmHex 6 Hex 8
11 11 11 11(2x) 14-2AWG (2x) 2.5-35mm2 (2x) 14-2AWG (2x) 2.5-35mm2
31lb.-in. 3.5Nm 31lb.-in. 3.5Nm(5x) 14-6AWG (5x) 2.5-16mm2 (5x) 14-6AWG (5x) 2.5-16mm2
17.5lb.-in. 2Nm 17.5lb.-in. 2Nm(4x) 14-8AWG (4x) 2.5-10mm2 (4x) 14-8AWG (4x) 2.5-10mm2
17.5lb.-in. 2Nm 17.5lb.-in. 2Nmstandard screwdriver standard screwdriver
UL File E98082 UL File E98082
• Quick mounting and wiring• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DIN Railmountable modular devices(height 95mm, depth 44.5mm)
• Accessories increase thenumber of outputs with onlyone input.
• No caps to open or remove• Material
Housing: PolyamideMetal Body: Brass
One Phase Power Distribution Block
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 35
38075 38073
Part Number:
Approvals
Current Rating
Voltage Rating
SCCR
No. of InputsWire RangeTorque
ScrewTypeNo. of Outputs
Wire RangeTorque
ScrewType
Dimensions:
38075 38073
115A 115A 175A 175A
600V AC 690V AC 600V AC 690V AC
100kA 100kA
3x1 3x1 3x1 3x18-2AWG 10-35mm2 8-2/0AWG 10-70mm2
31lb.-in. 3.5Nm 35.5lb.-in. 4NmHex 4 Hex 5
3x6 3x6 3x6 3x614-4AWG 2.5-16mm2 14-4AWG 2.5-16mm2
17.5lb.-in. 2Nm 17.5 lb.-in. 2NmHex 3 Hex 3
3 Pole 3 Pole
• Quick mounting and wiring• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DIN Railmountable modular devices
• Same compact size forboth ratings
• No caps to open or remove• Material
Housing: PolyamideMetal Body: Brass
UL File E98082 UL File E98082
Three Phase Power Distribution Block
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com36
• Quick mountingand wiring
• IP20 Finger Safe• DIN Rail or Panel Mount• No caps to open or remove• Material
Housing: PolyamideMetal Body: Aluminum
38064 38057
Part Number:
Approvals
Current Rating
Voltage Rating
No. of InputsWire RangeTorque
ScrewTypeNo. of Outputs
Wire RangeTorque
ScrewType
Dimensions:
38064
175A 175A
600V AC 690V AC
1 114-1AWG 2.5mm2-50mm2
106.2lb.-in. 12NmHex 5
1 114-1AWG 2.5mm2-50mm2
106.2lb.-in. 12NmHex 5
38057
400A 400A
600V AC 690V AC
1 16AWG-400MCM 16mm2-185mm2
221lb.-in. 25NmHex 10
1 16AWG-400MCM 16mm2-185mm2
221lb.-in. 25NmHex 10
38059
800A 800A
600V AC 690V AC
2 23AWG-600MCM 25-300mm2
310lb.-in. 35NmHex 10
2 23AWG-600MCM 25-300mm2
310lb.-in. 35NmHex 10
59.6
mm
(2.3
5in)
25.4 mm(1.0 in)
50 mm(1.97 in)
72.3
mm
(2.8
5in)
34.7
mm
(1.3
7in)
43.2
mm
(1.7
0in)
39 mm [1.54 in]
7 mm[0.28 in]
145.
5m
m[5
.73
in]
7.5 mm[0.30 in]
124.
4m
m[4
.90
in]
12 mm [0.47 in]
7 mm [0.28 in]
80.5 mm [3.17 in]
53.5 mm[2.11 in]
145
mm
[5.7
1in
]
129
mm
[5.0
8in
]
72 mm [2.83 in]
80.5 mm [3.17 in]
38059
UL File E98082 UL File E98082 UL File E98082
Splicer Blocks
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 37
CTT2.5UK/J/T/E
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Current Carrying Material
Type of Connection
Wire Range
Voltage Rating
Current Rating
Torque
Terminal Block
End Plate
Isolation Plate
DIN Railfor ordering informationrefer to page 63
End Clamp
MarkingTags(MTType)
10 mm
45 x 43 mm
9 mm
Polyamide 6.6
*4 screw clamps
24-12 AWG
300 V
10 A
7 lb-in
Cat. No. Std. Pk.
CTT2.5UK 50CTT2.5UJ 50CTT2.5UT 50CTT2.5UE 50
EP2.5/4UN 50
PP2.5/4UN 50
CA802 100CA702 100
CA509/K5
Altech thermocouple terminalblocks are designed for use intemperature measuring circuits.
The current carrying part of theterminal blocks have the samematerial (according to DIN437134and DIN43714) which is used forcompensating cables in the tem-perature measurement circuit (upto 200°C).
The terminal block is marked forthe respective type of thermocou-ple which enables easy identifica-tion for wiring.
*• CTT2.5UK ‘K’ type -Chromel (NiCr)Alumel (NiAl)
• CTT2.5UJ ‘J’ type -Iron (Fe)Constantan (CuNi)
• CTT2.5UT ‘T’ type -Copper (Cu)Constantan (CuNi)
• CTT2.5UE ‘E’ type -Chromel (NiCr)Constantan (CuNi)
Thermocouple(Sensor)
MeasuringInstrument
ThermocoupleTerminal Block
ThermocoupleTerminal Block
ReferenceJunction
Compensating Cable Supply Cable
Thermocouple Blocks
Diode Specifications
Diode 1N 4007
Diode Reverse Voltage 1000 V
Diode Current 1 A
1
3 4
C
2
1
3 4C
2
1
3 4C
2
D1
D2
D3
CDL4U(E)D1/D2 CDL4U(E)D3
6 mm
54 x 55.5 mm
300 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)D3 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/2 100CA705/3 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
6 mm
54 x 55.5 mm
300 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)D1 100CDL4U(E)D2 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/2 100CA705/3 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
With arc suppression circuit forcontactors and solenoid valves - DC
Diode circuit forreverse polarity protection
Altech offers different types ofterminals incorporating elec-tronic components for signalconverting, circuit protectionand status indication. Based oncustomer requirements, special-ly assembled terminals areoffered.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com38
TerminalWidth
Height x Length
Terminal Voltage
Stripping Length
Insulation Material
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
CurrentBars
Shorting Sleeve & Screw
MarkingTags
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
Indicator/ Diode Circuit
1
3 C
C
C
C
+4
2
1
3 -4
2
1
+3C C
C C
+4
2
1 2
+3 +4
1
3 +4
2
C
1
3 +4C
C
2
DD3DD1
DD2 DD4
D4 DD5
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 39
6 mm
54 x 55.5 mm
300 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)DD3 100CDL4U(E)DD4 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
6 mm
54 x 55.5 mm
300 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)DD1 100CDL4U(E)DD2 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
CDL4U(E)DD1/DD2 CDL4U(E)DD3/DD4
Diode circuit for lamp testing Diode circuit for lamp testing
6 mm
54 x 55.5 mm
12V~/24 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)DD5 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
6 mm
54 x 55.5 mm
12V~/24 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)D4 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
CDL4U(E)D4 CDL4U(E)DD5
Diode circuit for lamp testing withLED series resistance
Diode circuit for lamp testing withLED series resistance
E220514 E220514 E220514 E220514
Indicator/ Diode Circuit
CDL4U(E)N1 CDL4U(E)LD5* CDL4U(E)LD3*
6 mm
54 x 55.5 mm
24 V~, 48 V~, 120V~, 220V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)LD5* 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
6 mm
54 x 55.5 mm
110 V~ to 220 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)N1 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
AC voltage indicator with neon lamp
6 mm
54 x 55.5 mm
12 V~, 24 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)LD3* 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
AC/ DC voltage indicator with LEDAC voltage indicator with LED
1
3 4
2 1
3 4C +3 +4
+1
N1 LD5 LD3
* Add required voltage to part number as a suffix i.e. CDL4U(E)LD5/110 is for 110V.
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com40
TerminalWidth
Height x Length
Terminal Voltage
Stripping Length
Insulation Material
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
CurrentBars
Shorting Sleeve & Screw
MarkingTags
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
Indicator/ Diode Circuit
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 41
+1
-3 -4
-1
+3 +4
+1
-3
C
C
-4
-1
+3 +4
-1
+3 +4
C
L1LD1
LD2
6 mm
54 x 55.5 mm
24 V–
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)LD1 50CDL4U(E)LD2 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
6 mm
54 x 55.5 mm
24V~, 48 V~
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)LD4* 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
CDL4U(E)LD4* CDL4U(E)LD1/LD2
AC/ DC voltage indicator with LED
6 mm
54 x 55.5 mm
6 V–, 24 V–, 60 V–
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(E)L1* 50CDL4U(E)L2* 50
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
CDL4U(E)L1/L2* CDL4U(O)
DC voltage indicator with LED Electronic Component CarrierDC voltage indicator with LED
6 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 400 V 600 V
25 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CDL4U(O) 100
EPCDL4U 50
CA702 50CA802 50
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
MT2 100
L2
E220514 E220514 E220514 E220514
Indicator/ Diode Circuit
* Add required voltage to part number as a suffix i.e. CDL4U(E)LD5/110 is for 110V.
CDL4U(E)LA CDL4U(E)3LA
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Wire Range
Voltage Rating
Nominal Discharge Current
Peak Current
ResponseTime
Nominal Current
Capacitance
Application
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
MarkingTags (MTType)
12 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps
22-10 AWG
75, 90, 240, 600, 1000 V DC
20 KA (8/20µs)
–
100 ns
10A
<1.5 pf
For coarse line protection ofmeasuring, distributing or datacommunication interfaces.
Cat. No. Std. Pk.
CDL4U(E)LA75V 20CDL4U(E)LA90V 20CDL4U(E)LA230V 20CDL4U(E)LA600V 20CDL4U(E)LA1000V 20
EPCDL4U 50
CA702 50CA802 50
MT2 100
18 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps
22-10 AWG
90, 250, 350, 450 V DC
10 KA (8/20µs)
–
100 ns
5A
<1.0 pf
For simultaneous protection of linesagainst transversal (line/line) andlongitudinal (line/earth) surge.
Cat. No. Std. Pk.
CDL4U(E)3LA90V 20CDL4U(E)3LA230V 20CDL4U(E)3LA350V 20CDL4U(E)3LA600V 20
EPCDL4U 50
CA702 50CA802 50
MT2 100
Lightning Arrestor 3 Pole Lightning Arrestor
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com42
In applications where circuitprotection against transientovervoltage is required, AltechSurge Suppressor TerminalBlocks with built-in electroniccomponents are recommended.
These terminals are designed toprotect a single line against alongitudinal (line / earth) surge,thereby protecting distributionand inputs.
Note:CDL4U(E)SDU - For D.C.Application
CDL4U(E)SDB - For A.C.Application
A - Anode
K - Cathode
* Add required voltage topart number as a suffixi.e. CDL4U(E)LA/75 is for 75V.
Surge Suppressor
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 43
SDBSDUA SDUK
CDL4U(E)MOV1 CDL4U(E)SD CDL4U(E)RC
12 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps
22-10 AWG
12-48V DC / 12-160V AC**
1.5 KA
–
1 ns DC / 5 ns AC
10A
–
For fine protection of data interfaces, sen-sors, contacts, etc.
Cat. No. Std. Pk.
CDL4U(E)SDUA15V 20CDL4U(E)SDUA24V 20CDL4U(E)SDUA48V 20CDL4U(E)SDUK15V 20CDL4U(E)SDUK24V 20CDL4U(E)SDUK48V 20CDL4U(E)SDB15V 20CDL4U(E)SDB24V 20CDL4U(E)SDB48V 20CDL4U(E)SDB160V 20
EPCDL4U 50
CA702 50CA802 50
MT2 100
18 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps
22-10 AWG
250 V AC / 330 V DC
20A
–
–
10A
0.1 µf or 0.22 µf2
For protection of DC solenoid valvesand contactors
Cat. No. Std. Pk.
CDL4U(E)RC0.1 20CDL4U(E)RC0.22 20
EPCDL4U 50
CA702 50CA802 50
MT2 100
12 mm
54 x 55.5 mm
9 mm
Polyamide 6.6
4 screw clamps
22-10 AWG
130 V AC*
–
2kA-6.5kA (8/20µs)
<25ns
10A
100-20,000 pf
For protection from voltagesurge, spikes
Cat. No. Std. Pk.
CDL4U(E)MOV30V 20CDL4U(E)MOV60V 20CDL4U(E)MOV75V 20CDL4U(E)MOV130V 20CDL4U(E)MOV275V 20CDL4U(E)MOV460V 20CDL4U(E)MOV510V 20CDL4U(E)MOV625V 20CDL4U(E)MOV680V 20
EPCDL4U 50
CA702 50CA802 50
MT2 100
MOV Suppressor Diode RC Circuit
1 A fuse block is recommended to protect MOV terminals by disconnecting the faulted varistor. See pages 18-21 for fuse blocks.* Other voltages available upon request. Call Altech for voltage selection.** Phase to Phase / Phase to ground.
Surge Suppressor
CMT4For wire-to-wire connecting incontrol, automation, instrumen-tation and power distributionapplications.
Altech “miniature” terminalblocks offer tremendous spaceadvantage as demanded by cer-tain wiring configurations.
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
6 mm
29 x 27 mm
9 mm
Polyamide 6.6
2 screw clamps & 1 tapped holefor cross connection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300 V 400 V 300 V
35 A 32 A 35 A
6 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CMT4 100
EPCMT4 50
PPCMT4 50
CA602 100
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA747/2 100CA747/3 100CA747/4 100CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 100CA714/10 20
MT2 100
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com44
CGMT4
6 mm
28.5 x 27 mm
9 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
32A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CGMT4 50
MT2 100
E220514
AEx eIIEx eII
Mini Feed-Through 15mm
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 45
Certain electrical and control sys-tems require protection by fuses.The terminal has a hinged carrierthat has a specially designedspace for a cartridge type glassfuse of size Ø5 x 20 or Ø5 x 25mm. The fuse can be engaged ordisengaged by the movement ofthe carrier.
Altech fuse terminals are alsoavailable with light indication -CSFL 4U (L). A specially de-signedbuilt-in circuit gives light indica-tion in the event of fuse blow out.
† Fuses are sold separatelyAltech, see pages 23-24.
*Add required voltage to part number as a suffix, i.e. CSFL4U(L)/24 for 24V DC
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
Marking Tags (MT Type)(MT Type on Lever)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
CSFL4U CSFL4U(L)*
8 mm 43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25mm
22-10 AWG 22-10 AWG
600 V 600 V
6.3 A 10 A
7 lb-in 7 lb-in
Cat. No. Std. Pk. CSFL4U 100
EPCSFL4U 50
PPCSFL4U 50
CA602 100
CA711/2 100 CA711/3 50 CA711/4 50 CA711/10 20
MT8 100 MT2 100
8 mm 43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25mm
22-10 AWG 22-10 AWG
600 V 600 V
6.3 A 10 A
7 lb-in 7 lb-in
Cat. No. Std. Pk. CSFL4U(L)* 100
EPCSFL4U 50
PPCSFL4U 50
CA602 100
CA711/2 100 CA711/3 50 CA711/4 50 CA711/10 20
MT8 100 MT2 100
E220514 E220514
† Fuse not included. † Fuse not included.
Mini Feed-Through Fuse Block, 5 x 20 and 5 x 25 mm
24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC, 300V AC
EPCMB4
CMB4For use when space constraintsrequire extremely compactsolutions and internal jumpingis required.
Individual components can beused to build your own assem-blies. Just snap the requirednumber of terminal block com-ponents together and place aMounting Section on each end.
The CMB4 accepts internaljumpers and standard markingtags.
• Extremely compact andcost effective
• High density• Screw-cage clamp• Internal jumping provision• Polyamide 6.6• Standard color: gray
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
Mounting Section
Separator Plate
Mounting Screw*
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
6 mm
28 x 27 mm
9 mm
Polyamide 6.6
2screwclamps&1 tappedhole for cross connect.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300 V 400 V 300 V
35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CMB4 100
EPCMB4 50
SPCMB4 100
Any length M3 screw may be used.
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA747/2 100CA747/3 100CA747/4 100CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 100CA714/10 20
MT2 100
Dimensions mm (in.)CMB4
Mounting SectionEPCMB4
No. of HoleCat No. Poles Width (a) Spacing (b)CMB4/2 2 26 (1.02) 19 (0.75)CMB4/3 3 32 (1.26) 25 (0.98)CMB4/4 4 38 (1.50) 31 (1.22)CMB4/5 5 44 (1.73) 37 (1.46)CMB4/6 6 50 (1.97) 43 (1.69)CMB4/7 7 56 (2.20) 49 (1.93)CMB4/8 8 62 (2.44) 55 (2.17)CMB4/9 9 68 (2.68) 61 (2.40)CMB4/10 10 74 (2.91) 67 (2.64)CMB4/11 11 80 (3.15) 73 (2.87)CMB4/12 12 86 (3.39) 79 (3.11)CMB4/13 13 92 (3.62) 85 (3.35)CMB4/14 14 98 (3.86) 91 (3.58)CMB4/15 15 104 (4.09) 97 (3.82)CMB4/16 16 110 (4.33) 103 (4.06)CMB4/17 17 116 (4.57) 109 (4.29)CMB4/18 18 122 (4.80) 115 (4.53)CMB4/19 19 128 (5.04) 121 (4.76)CMB4/20 20 134 (5.28) 127 (5.00)CMB4/21 21 140 (5.51) 133 (5.24)CMB4/22 22 146 (5.75) 139 (5.47)CMB4/23 23 152 (5.98) 145 (5.71)CMB4/24 24 158 (6.22) 151 (5.94)
ba
* Any length M3 screw may be used.
Preassembled blocks arealso available for quickand easy installations.See Dimensions below.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com46
Mini Feed-Through Panel Mount
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 47
CENC4 CENC16 CENC35A quick reliable solution forground, neutral or low volt-age distribution applica-tions. The Busbar Systemconsists of a busbar, busbarsupports, and screw clampterminals for terminatingwires
NEB 10 (10 x 3 mm) andNEB 6 (6 x 6 mm), tin platedcopper busbars are avail-able in one meter lengths.Both have a 140A currentcarrying capacity.
NES plastic support withfixing screws for holding 10x 3 & 6 x 6 busbar makesplacing of busbar an easytask. Busbars up to 200 mmlength should be supportedat ends by two busbar sup-ports. For busbars exceed-ing 200 mm length, it is rec-ommended to provide inter-mediate busbar support.Easy to operate CENCclamp secures wire to thebusbar.
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Current Rating*
Torque
Other Approvals
Terminal Block**
Busbar(10 x 3 mm)
Busbar(6 x 6 mm)
Plastic Supportwith Fixing Screw
End Clamp/Bus barsupport for rail mounting
MarkingTags(MTType)
7.5 mm 9.8 mm 14.5 mm
30 x 23.3 mm 36 x 23.3 mm 45 x 27.3 mm
12 mm 16 mm 16 mm
Polyamide 6.6 Polyamide 6.6 Polyamide 6.6
1 screw clamp connection 1 screw clamp connection 1 screw clamp connection
22-10 AWG 0.5-6 sq.mm 22-12 AWG 10-4 AWG 6-16 sq.mm 10-6 AWG 8-2 AWG 10-35 sq.mm 8-2 AWG
35 A 41 A 80 A 76 A 125 A 125 A
14 lb-in 0.8 Nm 14 lb-in 14 lb-in 2.0 Nm 17.5 lb-in 25 lb-in 2.5 Nm 25 lb-in
Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
CENC4 50 CENC16 50 CENC35 50
NEB10 1 m NEB10 1 m NEB10 1 m
NEB6 1 m NEB6 1 m NEB6 1 m
NES 50 NES 50 NES 50
CA202 50 CA202 50 CA202 50
MT5 100 MT6 100 MT6 100
* 140A current carrying capacity of busbar should be takeninto account while connecting loads.
** Consult for other available colors.
E220514 E220514 E220514
Busbar System
CSTSN4U CSTSN5U
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Protective Coverfor covering
Protective Coverin Length
Insulated RemovableJumpers
Insulated PermanentJumpers
MarkingTags (MTType)
2Terminal3Terminal
100 mm200 mm300 mm
2 way3 way4 way
2 way3 way4 way
17 mm
39.5 x 50 mm
12 mm
Polyamide 6.6
2 screw connectionfor M4 ring/fork lugs
22-6 AWG 1.5-10 sq.mm 22-6 AWG
600 V 800 V 600 V
65 A 57 A 65 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CSTSN4U 100
EPCSTSN5U 50
CA702 50CA802 50
CSTSPC1 100CSTSPC1-1 100
CSTSPC1-2 10CSTSPC1-3 10CSTSPC1-4 10
CA514/1-2 100CA514/1-3 50CA514/1-4 50
CA514/3-2 100CA514/3-3 50CA514/3-4 50
MT2 100
Altech DIN rail mounting StudType Terminal Blocks are pre-ferred for the connections thatare subjected to very severevibrations.
The wire is crimped to a ring /fork type lug and is screwed onto the flat current bar in termi-nal.The range includes terminalblocks for wires of size 22-4AWG.
Jumpering can be achievedwith the aid of externaljumpers. The jumpers are insu-lated to make them shock proof.The terminal blocks have mark-er holding recess to accommo-date MT type marking tags.
It is recommended to use pro-tective covers in transparentplastic because assemblies ofthese terminals blocks are notfully covered.
17 mm
39.5 x 50 mm
12 mm
Polyamide 6.6
2 screw connectionfor M5 ring/fork lugs
22-4 AWG 1.5-16 sq.mm 22-4 AWG
600 V 800 V 600 V
80 A 76 A 80 A
17.5 lb-in 2.0 Nm 17.5 lb-in
Cat. No. Std. Pk.
CSTSN5U 100
EPCSTSN5U 50
CA702 50CA802 50
CSTSPC1 100CSTSPC1-1 100
CSTSPC1-2 10CSTSPC1-3 10CSTSPC1-4 10
CA514/1-2 100CA514/1-3 50CA514/1-4 50
CA514/3-2 100CA514/3-3 50CA514/3-4 50
MT2 100
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com48
E220514 E220514
Stud Type Block
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 49
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Protective Coverfor covering
Protective Coverin Length
Insulated RemovableJumpers
Insulated PermanentJumpers
MarkingTags (MTType)
2Terminal3Terminal
100 mm200 mm300 mm
2 way3 way4 way
2 way3 way4 way
CSTSB4U CSTSB5U
17 mm
39.5 x 50 mm
12 mm
Polyamide 6.6
2 screw connectionfor M4 ring/fork lugs
22-6 AWG 1.5-10 sq.mm 22-6 AWG
600 V 800 V 600 V
65 A 57 A 65 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
CSTSB4U 100
EPCSTN5U 50
CA702 50CA802 50
CSTSPC1 100CSTSPC1-1 100
CSTSPC1-2 10CSTSPC1-3 10CSTSPC1-4 10
CA514/1-2 100CA514/1-3 50CA514/1-4 50
CA514/3-2 100CA514/3-3 50CA514/3-4 50
MT2 100
17 mm
39.5 x 50 mm
12 mm
Polyamide 6.6
2 screw connectionfor M5 ring/fork lugs
22-4 AWG 1.5-16 sq.mm 22-4 AWG
600 V 800 V 600 V
80 A 76 A 80 A
17.5 lb-in 2.0 Nm 17.5 lb-in
Cat. No. Std. Pk.
CSTSB5U 100
EPCSTN5U 50
CA702 50CA802 50
CSTSPC1 100CSTSPC1-1 100
CSTSPC1-2 10CSTSPC1-3 10CSTSPC1-4 10
CA514/1-2 100CA514/1-3 50CA514/1-4 50
CA514/3-2 100CA514/3-3 50CA514/3-4 50
MT2 100
E220514 E220514
Stud Type Block
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
Stud Size / Operated by
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering info.refer to page 72
RemovableShorting Link
Insulated RemovableShorting Link
PermanantShorting Link
Insulated PermanentJumpers
Marking Tags (K Type)
2 way3 way4 way
2 way3 way4 way
2 way3 way4 way
2 way3 way4 way
11 mm
50.5 x 46 mm
10 mm
Polyamide 6.6
2 stud flat connection
M4 / Screwdriver
22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 800 V 600 V
50 A 41 A 50 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
STH4 100
EPSTH4 50
CA702 100CA802 50
CA512/13-2 100CA512/13-3 50CA512/13-4 50
CA514/13-2 100CA514/13-3 50CA514/13-4 50
CA512/14-2 100CA512/14-3 50CA512/14-4 50
CA514/14-2 100CA514/14-3 50CA514/14-4 50
CA509/K10 100
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com50
STH4
11 mm
50.5 x 86 mm
10 mm
Polyamide 6.6
2 stud flat connection
M4 / Screwdriver
22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 800 V 600 V
50 A 41 A 35 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
STH4DT 100
EPSTH4DT 50
CA702 100CA802 50
CA512/13-2 100CA512/13-3 50CA512/13-4 50
CA514/13-2 100CA514/13-3 50CA514/13-4 50
CA512/14-2 100CA512/14-3 50CA512/14-4 50
CA514/14-2 100CA514/14-3 50CA514/14-4 50
CA509/K10 100
STH4DT
22 mm
50.5 x 86 mm
10 mm
Polyamide 6.6
2 stud flat connection
M4 / Screwdriver
22-8 AWG 1.5-6 sq.mm 22-8 AWG
600 V 800 V 300 V
10 A 10 A 25 A
14 lb-in 1.2 Nm 14 lb-in
Cat. No. Std. Pk.
STH4DTSH 100
EPSTH4DT 50
CA702 100CA802 50
CA512/13-2 100CA512/13-3 50CA512/13-4 50
CA514/13-2 100CA514/13-3 50CA514/13-4 50
CA512/14-2 100CA512/14-3 50CA512/14-4 50
CA514/14-2 100CA514/14-3 50CA514/14-4 50
CA509/K10 100
STH4DTSHSTH Series TerminalBlocks are preferred forapplication where the con-nections are subjected tosevere vibration. The wireis crimped to a ring / forklug and is screwed on tothe flat current bar of theTerminal Block. The hingedcarrier should be lifted toinsert the lugs and thenfastened to complete theconnection.
By virtue of the hingeddesign, the TerminalBlocks apart from shroud-ing the live parts, provid-ing IP 20 (Finger Safe) pro-tection, saves consider-able time in wiring.
Two Lugs can be connect-ed to the Terminal, withoutsacrificing the safety ofthe Terminal Block.
STH4DT Disconnect & TestTerminal Block is used formeasuring, control andregulatory circuits. Theyprovide a clear functionaladvantage for deviceshaving utility instrumentsand associated transform-ers.
Socket Headed Screws actas test monitoring pointon either side of theTerminal Block. Discon-nection is achieved bymeans of a slide link oper-ated with a Screw Driver.
STH4DTSH Terminal Blockhas 2 STH4DT TerminalBlock shorted to achieveswitchable cross connec-tion (on one side).
Note: The disconnectingdevice is not suitable forinterrupting load. The sup-ply must be switched offbefore operating the slidelink / moving the hingedcarrier.
Hinge Type Stud Block
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 51
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Protective Cover
Marker Holder
InternalJumper
MarkingTags (KType)
2 way3 way4 way
25 mm
62 x 113 mm
18 mm / M6
Polyamide 6.6
2 bolts for connection
8-2 AWG 16-35 sq.mm 8-2 AWG
600 V 1000 V 600 V
130 A 125 A 130 A
27 lb-in 3.0 Nm 27 lb-in
Cat. No. Std. Pk.
PTB35 100
CA702 100CA102 50CA202 50
PSPTB35 40
MHPTB35 40
CA703/9 10CA704/9 10CA705/9 10
CA509/K9 100
PTB35
25 mm
65 x 169 mm
18 mm / M6
Polyamide 6.6
2 bolts for connection
8-2 AWG 16-35 sq.mm 8-2 AWG
600 V 1000 V 600 V
130 A 125 A 130 A
27 lb-in 3.0 Nm 27 lb-in
Cat. No. Std. Pk.
PTB35SH 100
CA702 100CA102 50CA202 50
CA703/9 10CA704/9 10CA705/9 10
CA509/K9 100
PTB35SHPTB seriesTerminal Blocks are pre-ferred for application using wiresof large cross section. The Wire iscrimped to a ring / fork lug and isscrewed on to the flat current barof the Terminal Block. Speciallydesigned Mounting Feet holds theTerminal Block rigidly on to theMounting Rail.
Two Lugs of 35 sq.mm can be con-nected to theTerminal Block, with-out sacrificing the safety of theTerminal Block. Hinged ProtectiveCover makes the Terminal Blockshock proof (finger safe) and hasmarker recess to accept markingtag.
TheTerminal Blocks can be stackedtogether by pressing the adjacentTerminal Blocks firmly*. InPTB35SH series Terminal Blocks,adjacent terminals can be shortedby removing a thin wall partitionand using 2/3/4 way shorting link.
Optional Marker Holder MHPTB35can be used for installing markingtags on the Terminal Blocks with-out protective covers.
* M3 Screw of desired length withnut can be used optionally tosecure the stack.
Marker Holder
Power Block
➀ UL recognition in progress.
➀UL ➀UL
CSC6T1-2
8 mm
45 x 94 mm
15 mm
Polyamide 6.6
3 spring clamps & 2 slots for interconnection
22-8 AWG 0.5-6 sq.mm. 22-8 AWG
600V 800V 600V
50A 41A 50A
Cat. No. Std. Pk.
CSC6T1-2 50
EPCSC6T1-2 50
CA702 50CA802 50
CA801/3 100CA801/3-3 100
CA901/3 100
MT8 100MT6F 100
ADL2.5
5 mm
50 x 79.5 mm
14 mm
Polyamide 6.6
4 spring clamps & 4 slots for interconnection
22-12 AWG 2.5 sq.mm. 22-12 AWG
300V 800V 300V
20A 24A 25A
Cat. No. Std. Pk.
ADL2.5 50
EPADL2.5 50
CA702 50CA802 50
CA801/1 100CA801/1-3 100
CA901/1 100
MT5 100MT6F 100
CSC4T2-2
6 mm
42 x 105 mm
13 mm
Polyamide 6.6
4 spring clamps & 2 slots for interconnection
22-12 AWG 0.5-4 sq.mm. 22-12 AWG
600V 800V 600V
25A 32A 25A
Cat. No. Std. Pk.
CSC4T2-2 50
EPCSC4T2-2 50
CA702 50CA802 50
CA801/2 100CA801/2-3 100
CA901/2 100
MT6 100MT6F 100
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Jumpers AdjacentAlternate
Push in typewire jumper
MarkingTags(MTType)
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com54
Feed-Through & Multi-Connection Spring Clamp
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 55
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Tyoe of fuse used
LED Voltage
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Insulated Jumper(2 pole)
MarkingTags(MTType)
ASF4Altech offers ‘Screwless’ SpringClamp FuseTerminal Blocks.
The terminal has a moving typehinged carrier that has speciallydesigned space for cartridgetype glass fuse of size Ø 5 x 20or Ø 5 x 25 mm.The fuse can beengaged or disengaged by themovement of the carrier.
Cross connection is possiblewith specially designed push-intype jumpers.
8 mm
60 x 86 mm
16 mm
Polyamide 6.6
2 spring clamps & 2 slots for interconnection
Ø5x20, Ø5x25 mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A
Cat. No. Std. Pk.
ASF4 100
EPASF4 50
CA702 50CA802 50
CA801/7 100
MT8 100
ASF4(L)*
8 mm
60 x 86 mm
16 mm
Polyamide 6.6
2 spring clamps & 2 slots for interconnection
Ø5x20, Ø5x25 mm
24V AC/DC, 48V AC/DC110V AC/DC, 220V AC
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 6.3 A
Cat. No. Std. Pk.
ASF4(L)* 100
EPASF4 50
CA702 50CA802 50
CA801/7 100
MT8 100
*Add required voltage to part number as a suffix. i.e. ASF4(L)/24 for 24V AC/DC.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Fuse Spring Clamp, 5 x 20 and 5 x 25mm
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
DIN Railfor ordering informationrefer to page 70
MarkingTags(MTType)
CSCG2.5T CSCG4TAltech offers ‘Screwless’ SpringClamp GroundTerminal Blocks.Specially designed alloy feethelps in achieving very lowcontact resistance and vibrationproof grounding.
CSCG series terminals can bemounted on Din 35 rail alongwith other terminal blocks ofCSC series. The terminal blockprofile matches with that ofCSC terminal block of samewire size.
Special features of CSCG termi-nal blocks are:
• Vibration proof grounding
• Very low contactresistance because ofspecial alloy feet
• Drop-on groundingconnection
• Spring clamp to acceptsolid and stranded wire
5 mm
36 x 58 mm
15 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
800 V
24 A
Cat. No. Std. Pk.
CSCG2.5T 100
MT5 100
6 mm
42 x 65 mm
13 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-12 AWG 0.5-4 sq.mm 22-12 AWG
800 V
32 A
Cat. No. Std. Pk.
CSCG4T 100
MT6 100
*E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com56
Ground Spring Clamp
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 57
CSCG6T
8 mm
45 x 72 mm
15 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-8 AWG 0.5-6 sq.mm 22-8 AWG
800 V
41 A
Cat. No. Std. Pk.
CSCG6T 50
MT8 100
CSCG10T CSCG16T
10 mm
50 x 75 mm
18 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
16-6 AWG 1.5-10 sq.mm 16-6 AWG
800 V
57 A
Cat. No. Std. Pk.
CSCG10T 50
MT10 100
E220514
12 mm
58 x 82 mm
20 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
16-6 AWG 1.5-16 sq.mm 16-6 AWG
800 V
76 A
Cat. No. Std. Pk.
CSCG10T 50
MT12 100
Ground Spring Clamp
➀ UL recognition in progress.
➀UL ➀UL
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com58
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
Partition Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Jumpers Adjacent
Jumpers Alternate
Push in typewire jumper
Step DownJumper
MarkingTags(KType)
These Terminal Bocks arean ideal choice for compactjunction boxes having limi-tations of space and height.
A major advantage ofAngular Terminal Blocksover the top wire entryTerminal Blocks is that theirprofile remains the sameacross the entire range ofFeed Through, MultipleConnection, Ground andGround Multiple Connec-tionTerminal Blocks.
The other advantagesinclude: Angular entry ofwires saving in conductorlength, marking / identifica-tion facility on the center(top) of the block,Multiplication of connec-tions through bridging.
Step Down shorting linksare used for shorting springclamp Terminal Blocks ofdifferent sizes. For moredetails refer to page 77.
AS2.5
5 mm
42 x 54 mm
16 mm
Polyamide 6.6
2 spring clamps& 2 slots for interconnection
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
600V 800 V 600 V
25 A 24 A 25 A
Cat. No. Std. Pk.
AS2.5 100
EPAS2.5 50
CA702 50CA802 50
CA801/1 100
CA801/1-3 100
CA901/1 100
CA901/5 100CA901/6 100
MT5 100MT6F 10
E220514
AS4
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
2 spring clamps& 2 slots for interconnection
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
600V 800 V 600 V
35 A 32 A 35 A
Cat. No. Std. Pk.
AS4 100
EPAS4 50
CA702 50CA802 50
CA801/2 100
CA801/2-3 100
CA901/2 100
CA901/4 100CA901/6 100
MT6 100MT6F 10
Angular Feed-Through Spring Clamp
➀ UL recognition in progress.
➀UL
seepage 78
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 59
AS6
8 mm
48 x 74 mm
15 mm
Polyamide 6.6
2 spring clamps& 2 slots for interconnection
22-8 AWG 0.5-6 sq.mm. 22-8 AWG
600V 800 V 600 V
50 A 41 A 50 A
Cat. No. Std. Pk.
AS6 50
EPAS6 50
CA702 50CA802 50
CA801/3 100
CA801/3-3 100
CA901/3 100
CA901/4 100CA901/5 100
MT8 100MT6F 10
AS2.5/3
5 mm
42 x 54 mm
12 mm
Polyamide 6.6
3 spring clamps& 2 slots for interconnection
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
600V 800 V 600 V
25A 24 A 25 A
Cat. No. Std. Pk.
AS2.5/3 100
EPAS2.5 50
CA702 50CA802 50
CA801/1 100
CA801/1-3 100
CA901/1 100
CA901/5 100CA901/6 100
MT5 100MT6F 10
E220514
AS2.5/4
5 mm
42 x 54 mm
12 mm
Polyamide 6.6
4 spring clamp connection
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
600V 800 V 600 V
25 A 24 A 25 A
Cat. No. Std. Pk.
AS2.5/4 100
EPAS2.5 50
CA702 50CA802 50
MT5 100MT6F 10
E220514
Angular Feed-Through Spring Clamp
➀ UL recognition in progress.
➀UL
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com60
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
Partition Plate
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
Jumpers Adjacent
Jumpers Alternate
Push in typewire jumper
Step DownJumper
MarkingTags(KType)
AS4/3
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
3 spring clamps& 2 slots for interconnection
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
600V 800 V 600 V
35 A 32 A 35 A
Cat. No. Std. Pk.
AS4/3 100
EPAS4 50
CA702 50CA802 50
CA801/2 100
CA801/2-3 100
CA901/2 100
CA901/4 100CA901/6 100
MT6 100MT6F 10
AS4/4
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
4 spring clamp connection
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
600V 800 V 600 V
35 A 32 A 35 A
Cat. No. Std. Pk.
AS4/4 100
EPAS4 50
CA702 50CA802 50
MT6 100MT6F 10
AS6/3
8 mm
42 x 74 mm
15 mm
Polyamide 6.6
3 spring clamps& 2 slots for interconnection
22-8 AWG 0.5-6 sq.mm. 22-8 AWG
600V 800 V 600 V
50 A 41 A 50 A
Cat. No. Std. Pk.
AS6/3 50
EPAS6 50
CA702 50CA802 50
CA801/3 100
CA801/3-3 100
CA901/3 100
CA901/4 100CA901/6 100
MT8 100MT6F 10
Angular Feed-Through Spring Clamp
➀ UL recognition in progress.
➀UL ➀UL ➀UL
seepage 78
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 61
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
Marking Tags
Besides having angularwire entry, these TerminalBlocks have speciallydesigned alloy feet whichhelp in achieving very lowcontact resistance andvibration proof groundingwith DIN rails. They aregreen / yellow colorcoded as per industrystandards.
AGT2.5
5 mm
42 x 54 mm
16 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
800 V 600 V
24 A
Cat. No. Std. Pk.
AGT2.5 100
EPAS2.5 50
MT5 100
E220514
AGT4
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
800 V 800 V
32 A
Cat. No. Std. Pk.
AGT4 100
EPAS4 50
MT6 100
Angular Ground / Earth Spring Clamp
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com62
Terminal Width
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Plate
DIN Railfor ordering informationrefer to page 70
Marking Tags(K Type)
AGT6
8 mm
48 x 74 mm
15 mm
Polyamide 6.6
2 spring clamp connection,grounding through alloy feet
22-8 AWG 0.5-6 sq.mm. 22-8 AWG
800 V 800 V
41 A
Cat. No. Std. Pk.
AGT6 50
EPAS6 50
MT8 100
AGT2.5/3
5 mm
42 x 54 mm
12 mm
Polyamide 6.6
3 spring clamp connection,grounding through alloy feet
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
800 V 600 V
24 A
Cat. No. Std. Pk.
AGT2.5/3 100
EPAS2.5 50
MT5 100
E220514
AGT2.5/4
5 mm
42 x 54 mm
12 mm
Polyamide 6.6
4 spring clamp connection,grounding through alloy feet
22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG
800 V
24 A
Cat. No. Std. Pk.
AGT2.5/4 100
EPAS2.5 50
MT5 100
E220514
Angular Ground / Earth Spring Clamp
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 63
AGT4/3
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
3 spring clamp connection,grounding through alloy feet
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
800 V 800 V
32 A
Cat. No. Std. Pk.
AGT4/3 50
EPAS4 50
MT6 100
AGT4/4
6 mm
42 x 61.5 mm
14 mm
Polyamide 6.6
4 spring clamp connection,grounding through alloy feet
22-10 AWG 0.5-4 sq.mm. 22-10 AWG
800 V 800 V
32 A
Cat. No. Std. Pk.
AGT4/4 50
EPAS4 50
MT6 100
AGT6/3
8 mm
48 x 74 mm
15 mm
Polyamide 6.6
3 spring clamp connection,grounding through alloy feet
22-12 AWG 0.5-2.5 sq.mm. 22-8 AWG
800 V 800 V
41 A
Cat. No. Std. Pk.
AGT6/3 50
EPAS6 50
MT8 100
Angular Ground / Earth Spring Clamp
E220514 E220514E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com64
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Section(set of left and right)
Insulated Jumper(2 pole)
OperatingTool
MarkingTags(MTType)
5 mm
27 x 35 mm
14 mm
Polyamide 6.6
2 spring clamp connections
22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
600 V 750 V 600 V
20 A 24 A 20 A
Cat. No. Std. Pk.
CSCP2.5T 100
EPCSCP2.5T 25
CA803/1 100
SCA2-5 1
MT4 100
10 mm
27 x 35 mm
14 mm
Polyamide 6.6
4 spring clamp connections
22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
600 V 750 V 600 V
20 A 24 A 20 A
Cat. No. Std. Pk.
CSCP2.5T2 100
EPCSCP2.5T 25
CA803/1 100
SCA2-5 1
MT3 100
Altech “screwless” springclamp panel mount termi-nal blocks are an excellentsolution for extremelycompact wiring applica-tions.
These terminal blocks are“add-on” type and can becombined to form multi-pole assemblies. Thestacked assembly is fittedwith mounting end sec-tions on both ends foreasy installation on to thepanel.
The terminal has markerholding recessess on threesides to accept markingtags. Cross connection canbe achieved with the aid ofinsulated jumpers.
The CSCP2.5T2 panelmount terminal blockshave two connectionpoints on each side all withthe same potential.The ter-minals provide possibilityof further multiplicationthrough jumpering.
CSCP2.5T
EPCSCP2.5T
CSCP2.5T2EPCSCP2.5TCOLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Panel Mount Spring ClampCSCP2.5T CSCP2.5T2
CMT4For wire-to-wire connecting incontrol, automation, instrumen-tation and power distributionapplications.
Altech “miniature” terminalblocks offer tremendous spaceadvantage as demanded by cer-tain wiring configurations.
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
6 mm
29 x 27 mm
9 mm
Polyamide 6.6
2 screw clamps & 1 tapped holefor cross connection
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300 V 400 V 300 V
35 A 32 A 35 A
6 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CMT4 100
EPCMT4 50
PPCMT4 50
CA602 100
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA747/2 100CA747/3 100CA747/4 100CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 100CA714/10 20
MT2 100
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com44
CGMT4
6 mm
28.5 x 27 mm
9 mm
Polyamide 6.6
2 screw clamps
22-10 AWG 0.5-4 sq.mm 22-10 AWG
32A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CGMT4 50
MT2 100
E220514
AEx eIIEx eII
Mini Feed-Through 15mm
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 45
Certain electrical and control sys-tems require protection by fuses.The terminal has a hinged carrierthat has a specially designedspace for a cartridge type glassfuse of size Ø5 x 20 or Ø5 x 25mm. The fuse can be engaged ordisengaged by the movement ofthe carrier.
Altech fuse terminals are alsoavailable with light indication -CSFL 4U (L). A specially de-signedbuilt-in circuit gives light indica-tion in the event of fuse blow out.
† Fuses are sold separatelyAltech, see pages 23-24.
*Add required voltage topart number as a suffix, i.e.CSFL4U(L)/24 for 24V DC
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
LED Voltage
Type of Fuse Used
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
End Plate
Isolation Partition
DIN Railfor ordering informationrefer to page 70
End Stopfor ordering informationrefer to page 72
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)(MTType on Lever)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
CSFL4U CSFL4U(L)*
8 mm
43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 8 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CSFL4U 100
EPCSFL4U 50
PPCSFL4U 50
CA602 100
CA711/2 100CA711/3 50CA711/4 50CA711/10 20
MT8 100MT2 100
8 mm
43 x 58 mm
9.5 mm
Polyamide 6.6
2 screw clamps
Ø5x20, Ø5x25mm
22-10 AWG 0.5-4 sq.mm 22-10 AWG
600 V 500 V 600 V
6.3 A 6.3 A 8 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CSFL4U(L)* 100
EPCSFL4U 50
PPCSFL4U 50
CA602 100
CA711/2 100CA711/3 50CA711/4 50CA711/10 20
MT8 100MT2 100
E220514 E220514
† Fuse not included. † Fuse not included.
Mini Feed-Through Fuse Block, 5 x 20 and 5 x 25 mm
24VAC/DC,48VAC/DC,110VAC/DC, 220VAC,300VAC
EPCMB4
CMB4For use when space constraintsrequire extremely compactsolutions and internal jumpingis required.
Individual components can beused to build your own assem-blies. Just snap the requirednumber of terminal block com-ponents together and place aMounting Section on each end.
The CMB4 accepts internaljumpers and standard markingtags.
• Extremely compact andcost effective
• High density• Screw-cage clamp• Internal jumping provision• Polyamide 6.6• Standard color: gray
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
Terminal Block
Mounting Section
Separator Plate
Mounting Screw*
InternalJumper
InsulatedInternalJumper
CurrentBars
Shorting Sleeve & Screw
ExternalJumper
MarkingTags (MTType)
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
2 pole3 pole4 pole10 pole
10 pole (breakable)100 pole
2 pole3 pole4 pole10 pole
6 mm
28 x 27 mm
9 mm
Polyamide 6.6
2screwclamps&1 tappedhole for cross connect.
22-10 AWG 0.5-4 sq.mm 22-10 AWG
300 V 400 V 300 V
35 A 32 A 35 A
7 lb-in 0.5 Nm 7 lb-in
Cat. No. Std. Pk.
CMB4 100
EPCMB4 50
SPCMB4 100
Any length M3 screw may be used.
CA727/2 100CA727/3 100CA727/4 100CA727/10 10
CA747/2 100CA747/3 100CA747/4 100CA747/10 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10
CA607/S/Q 100
CA714/2 100CA714/3 100CA714/4 100CA714/10 20
MT2 100
Dimensions mm (in.)CMB4
Mounting SectionEPCMB4
No. of HoleCat No. Poles Width (a) Spacing (b)CMB4/2 2 26 (1.02) 19 (0.75)CMB4/3 3 32 (1.26) 25 (0.98)CMB4/4 4 38 (1.50) 31 (1.22)CMB4/5 5 44 (1.73) 37 (1.46)CMB4/6 6 50 (1.97) 43 (1.69)CMB4/7 7 56 (2.20) 49 (1.93)CMB4/8 8 62 (2.44) 55 (2.17)CMB4/9 9 68 (2.68) 61 (2.40)CMB4/10 10 74 (2.91) 67 (2.64)CMB4/11 11 80 (3.15) 73 (2.87)CMB4/12 12 86 (3.39) 79 (3.11)CMB4/13 13 92 (3.62) 85 (3.35)CMB4/14 14 98 (3.86) 91 (3.58)CMB4/15 15 104 (4.09) 97 (3.82)CMB4/16 16 110 (4.33) 103 (4.06)CMB4/17 17 116 (4.57) 109 (4.29)CMB4/18 18 122 (4.80) 115 (4.53)CMB4/19 19 128 (5.04) 121 (4.76)CMB4/20 20 134 (5.28) 127 (5.00)CMB4/21 21 140 (5.51) 133 (5.24)CMB4/22 22 146 (5.75) 139 (5.47)CMB4/23 23 152 (5.98) 145 (5.71)CMB4/24 24 158 (6.22) 151 (5.94)
ba
* Any length M3 screw may be used.
Preassembled blocks arealso available for quickand easy installations.See Dimensions below.
COLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com46
Mini Feed-Through Panel Mount
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com64
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Voltage Rating
Current Rating
Other Approvals
Terminal Block
End Section(set of left and right)
Insulated Jumper(2 pole)
OperatingTool
MarkingTags(MTType)
5 mm
27 x 35 mm
14 mm
Polyamide 6.6
2 spring clamp connections
22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
600 V 750 V 600 V
20 A 24 A 20 A
Cat. No. Std. Pk.
CSCP2.5T 100
EPCSCP2.5T 25
CA803/1 100
SCA2-5 1
MT4 100
10 mm
27 x 35 mm
14 mm
Polyamide 6.6
4 spring clamp connections
22-14 AWG 0.5-2.5 sq.mm 22-14 AWG
600 V 750 V 600 V
20 A 24 A 20 A
Cat. No. Std. Pk.
CSCP2.5T2 100
EPCSCP2.5T 25
CA803/1 100
SCA2-5 1
MT3 100
Altech “screwless” springclamp panel mount termi-nal blocks are an excellentsolution for extremelycompact wiring applica-tions.
These terminal blocks are“add-on” type and can becombined to form multi-pole assemblies. Thestacked assembly is fittedwith mounting end sec-tions on both ends foreasy installation on to thepanel.
The terminal has markerholding recessess on threesides to accept markingtags. Cross connection canbe achieved with the aid ofinsulated jumpers.
The CSCP2.5T2 panelmount terminal blockshave two connectionpoints on each side all withthe same potential.The ter-minals provide possibilityof further multiplicationthrough jumpering.
CSCP2.5T
EPCSCP2.5T
CSCP2.5T2EPCSCP2.5TCOLOR BLOCKS(other than grey standard)
When ordering please addcolor suffix to Cat. No.
Example: CTS2.5U-N/R
Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB
E220514 E220514
Panel Mount Spring ClampCSCP2.5T CSCP2.5T2
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 65
High Temperature Ceramic EuroBlocks™
CB16CB4 CB6
W1
T T T
C2 W3
C3
D1
D2
W3
TT
HH
D1
D2
H
W2
H
W2
H
Dimensions mm
Note: All dimensions are shown in mm, to convert to inches please divide by 25.4.
Suitable for use in high tem-perature applications up to600°C (1112°F). Applicationsinclude hot melt glue guns,furnaces, heaters, processequipment and machinery.Terminal blocks are offeredwith mounting holes for panelmounting or free floatingapplications.
• Compact, space saving• Tubular screw clamp• Free float or panel mount• Temperature range:-40°C (-40°F) to600°C (1112°F)
• Standard color: white• MaterialHousing: SteatiteClamp: BrassScrews: Zinc plated steel
Ceramic
22-10 AWG 20-10 AWG
300V 300V
40 A 30 A
Cat. No. Std. Pk.
CB6/1 50
CB6/2H 50
CB6/3H 50
Insulation Material
Approvals
Wire Range
Voltage Rating
Current Rating
No. of Poles
1 (free floating)2 (free floating)2 (with mounting holes)3 (free floating)3 (with mounting holes)
Ceramic
20-6 AWG 18-6 AWG
300V 300V
76 A 65 A
Cat. No. Std. Pk.
CB16/2H 50
CB16/3H 50
Ceramic
24-12 AWG 24-12 AWG
300V 300V
30 A 20 A
Cat. No. Std. Pk.
CB4/1 50CB4/2 50CB4/2H 50CB4/3 50CB4/3H 50
W T H C D1 D2 Fixing StrippingScrew Length
CB4/1 1 POLE 23 11 18.5 * 6CB4/2 2 POLE 23 18 18.5 * 6CB4/2H 2 POLE 23 24 18.5 14.6 6 3.5 M3X16 6CB4/3 3 POLE 25 25 18.5 * 6CB4/3H 3 POLE 25.4 36 18.5 13 6 3.5 M3X16 6
CB6/1 1 POLE 25 12 19.5 * 6CB6/2H 2 POLE 25.5 26 19.5 12.6 6 M3X16 6CB6/3H 3 POLE 25.5 41 19.5 15 6 M3X16 6
CB16/2H 2 POLE 28 31 23.2 16.5 6 3.5 M3X20 8.5CB16/3H 3 POLE 27.5 48 23.2 17 6 3.5 M3X20 8.5
1 Pole 2 Pole 2 Pole withmounting hole
3 Pole 3 Pole withmounting hole
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 47
CENC4 CENC16 CENC35A quick reliable solution forground, neutral or low volt-age distribution applica-tions. The Busbar Systemconsists of a busbar, busbarsupports, and screw clampterminals for terminatingwires
NEB 10 (10 x 3 mm) andNEB 6 (6 x 6 mm), tin platedcopper busbars are avail-able in one meter lengths.Both have a 140A currentcarrying capacity.
NES plastic support withfixing screws for holding 10x 3 & 6 x 6 busbar makesplacing of busbar an easytask. Busbars up to 200 mmlength should be supportedat ends by two busbar sup-ports. For busbars exceed-ing 200 mm length, it is rec-ommended to provide inter-mediate busbar support.Easy to operate CENCclamp secures wire to thebusbar.
TerminalWidth
Height x Length
Stripping Length
Insulation Material
Type of Connection
Approvals
Wire Range
Current Rating*
Torque
Other Approvals
Terminal Block**
Busbar(10 x 3 mm)
Busbar(6 x 6 mm)
Plastic Supportwith Fixing Screw
End Clamp/Bus barsupport for rail mounting
MarkingTags(MTType)
7.5 mm 9.8 mm 14.5 mm
30 x 23.3 mm 36 x 23.3 mm 45 x 27.3 mm
12 mm 16 mm 16 mm
Polyamide 6.6 Polyamide 6.6 Polyamide 6.6
1 screw clamp connection 1 screw clamp connection 1 screw clamp connection
22-10 AWG 0.5-6 sq.mm 22-12 AWG 10-4 AWG 6-16 sq.mm 10-6 AWG 8-2 AWG 10-35 sq.mm 8-2 AWG
35 A 41 A 80 A 76 A 125 A 125 A
14 lb-in 0.8 Nm 14 lb-in 14 lb-in 2.0 Nm 17.5 lb-in 25 lb-in 2.5 Nm 25 lb-in
Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
CENC4 50 CENC16 50 CENC35 50
NEB10 1 m NEB10 1 m NEB10 1 m
NEB6 1 m NEB6 1 m NEB6 1 m
NES 50 NES 50 NES 50
CA202 50 CA202 50 CA202 50
MT5 100 MT6 100 MT6 100
* 140A current carrying capacity of busbar should be takeninto account while connecting loads.
** Consult for other available colors.
E220514 E220514 E220514
Busbar System
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 65
High Temperature Ceramic EuroBlocks™
CB16CB4 CB6
W1
T T T
C2 W3
C3
D1
D2
W3
TT
HH
D1
D2
H
W2
H
W2
H
Dimensions mm
Note: All dimensions are shown in mm, to convert to inches please divide by 25.4.
Suitable for use in high tem-perature applications up to600°C (1112°F). Applicationsinclude hot melt glue guns,furnaces, heaters, processequipment and machinery.Terminal blocks are offeredwith mounting holes for panelmounting or free floatingapplications.
• Compact, space saving• Tubular screw clamp• Free float or panel mount• Temperature range:-40°C (-40°F) to600°C (1112°F)
• Standard color: white• MaterialHousing: SteatiteClamp: BrassScrews: Zinc plated steel
Ceramic
22-10 AWG 20-10 AWG
300V 300V
40 A 30 A
Cat. No. Std. Pk.
CB6/1 50
CB6/2H 50
CB6/3H 50
Insulation Material
Approvals
Wire Range
Voltage Rating
Current Rating
No. of Poles
1 (free floating)2 (free floating)2 (with mounting holes)3 (free floating)3 (with mounting holes)
Ceramic
20-6 AWG 18-6 AWG
300V 300V
76 A 65 A
Cat. No. Std. Pk.
CB16/2H 50
CB16/3H 50
Ceramic
24-12 AWG 24-12 AWG
300V 300V
30 A 20 A
Cat. No. Std. Pk.
CB4/1 50CB4/2 50CB4/2H 50CB4/3 50CB4/3H 50
W T H C D1 D2 Fixing StrippingScrew Length
CB4/1 1 POLE 23 11 18.5 * 6CB4/2 2 POLE 23 18 18.5 * 6CB4/2H 2 POLE 23 24 18.5 14.6 6 3.5 M3X16 6CB4/3 3 POLE 25 25 18.5 * 6CB4/3H 3 POLE 25.4 36 18.5 13 6 3.5 M3X16 6
CB6/1 1 POLE 25 12 19.5 * 6CB6/2H 2 POLE 25.5 26 19.5 12.6 6 M3X16 6CB6/3H 3 POLE 25.5 41 19.5 15 6 M3X16 6
CB16/2H 2 POLE 28 31 23.2 16.5 6 3.5 M3X20 8.5CB16/3H 3 POLE 27.5 48 23.2 17 6 3.5 M3X20 8.5
1 Pole 2 Pole 2 Pole withmounting hole
3 Pole 3 Pole withmounting hole
E220514 E220514 E220514
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com80
Marking Systems
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 81
Marking Systems
• Identifiers for connectors, wires, cables and equipment• Cable ties, shrink tubing, labels and signs of different
sizes and materials, as well as customer-specific items.• Size: 14.9”x7.5”x1.77”• Weight: 6.6 lbs.
SCRIBERVS 210Scriber VS210
TThe VS200 base unit is a stand-aloneplotting system with an integral keyboardand display screen. The marker fixture,plotter pen, and the memory cassettehave to be inserted in the base unit tomake it operational. The base unit comesin an aluminum carrying case andincludes the memory cassette and thepower supply. A manual is available inEnglish and Spanish.
The VS 200 can be used to produce labelsof all types, with its fixture changeable ina matter of seconds.
The Vario VS 200 makes labeling easy. Themenu-driven program guides you quicklyand easily through all the steps.
It can be used at any time and in anyplace. Easily transported in its specialcase, the battery-operated (battery packsold separately) VS 200 can be operatedprecisely where you need it. The spaciouscase provides enough room for the exten-sive accessories.
Plotter VP 500
The VP 500 base unit is an auxiliary plotterand has to be connected to a PC via a par-allel port or USB connection. It is a highspeed plotting device and enables plottingof different markers in one setting. Themarker fixture and the plotter pen have tobe inserted before commencing the plot-ting operation. The base unit is primarilycontrolled through a PC with the help ofVario Sign software. Manual available inEnglish and Spanish.
The special design of the VP 500 enables itto hold different markers from variousmanufacturers at the same time. It is alsopossible to write on relatively large mark-ers with a maximum height 14 mm.
Fixtures
Fixtures are required for alignment ofmarkers with respect to the plotter pen.Different marker fixtures can be mountedon the plotter bed of the VP 500 at thesame time thereby reducing set up times.Fixtures for different markers from variousmanufacturers like Altech, Allen Bradley,Connectwell, ContaClip, Entrelec,Weidmuller, Phoenix Contact, PTR,Wieland, Wago, Murrplastik, Partex, SESSterling, etc. are available. For more infor-mation on ordering fixtures please contactAltech.
BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxxMEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000
Ordering Information
CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008
VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx ** See page 85.
Fixtures &MemoryCassette
Battery Pack Plotter Pen,Ink Cartridge
Fixtures Plotter Pen,Ink Cartridge
Vario Sign
PLOTTERVP 500CMPS 500 PLOTTER PACKAGE
• Identifiers for connectors, wires, cablesand equipment
• Cable ties, shrink tubing, labels and signsof different sizes and materials, as well ascustomer-specific items.
• Size: 26”x18”x4.9”
• CMPS plotter• Size: 17”x18”x4.9”• Tag Sizes: MT2, MT3, MT4, MT5, MT6,
MT8, MT9, MT10, MT12, MT15, MT20, MT25• CMPS software with cable• 2 fixtures for tags MT5-MT15
(MT9 sold separately)• 1 fixture for tags MT2 and MT25• 2 disposable pens
Ordering Information
Engraver VE500
The engraving unit was specificallydesigned to be used with the VP500 amdCMPS 500 plotters. Changing back andforth between the pen-plotter and theengraver is easy. The engraver is meantto engrave plastic signs on double sidedmaterial, pre-cut or blank sheets, for leg-end plates, push button inlays, etc. Theengraver is programmed by the VarioSignsoftware for ease of use and design flexi-bility.
Engraving Needles
These engraving needles are to be usedwith the VE500 engraver. They have a 15°angle and are available in 6 tip widths oras a complete set.
Vacuum Cleaner Bag
Replacement bags for the VE500engraver’s vacuum cleaner
ENGRAVERVE500
VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040
Ordering Information
VACUUM CLEANER BAG
VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000
Ordering Information
ENGRAVING NEEDLE
Product Width Order No.Engraving Needle 0.20mm 35010003Engraving Needle 0.30mm 35010002Engraving Needle 0.40mm 35010001Engraving Needle 0.50mm 35010000Engraving Needle 0.70mm 35010004Engraving Needle 1.00mm 35010005Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm) 35010006Engraving Needle(0.20 mm cutter stainless steel) 35012033
Ordering Information
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com82
Marking Systems
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 83
Marking Systems Accessories
Plotter PensThese “tubular-nib” pens are suitable forVario Scriber VS 200, Vario Plotter VP 500 andall current labeling and identification systemswith HP penholders. They are available in sixtip widths identified by body color - 0.18 mm,0.25 mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00mm; ink cartridge not supplied with pen.Special variants for other systems are avail-able on request. Specially designed pre-filledfelt-tip pens are available in a set of 4 colors(black, blue, red and green) and 2 sizes - 0.3and 0.7 mm.
Ink CartridgesThese are easy to insert “tubular-nib” pencartridges containing special black ink suit-able for marking, identifying and labeling vari-ous plastics. It is fast drying, smudge-proof,fade resistant, and resistant to chemicalswhen used on suitable plastic materials.
Disposable PensThe disposable pens use the same special inkas used in the ink cartridges. They deliver thesame outstanding durability and print qualityas the standard plotter pens with the conven-ience of a disposable pen. These pre-filledpens allow for fast, efficient and cost effectiveprinting without refilling ink or cleaning. Theyare available in two tip widths, 0.25 mm and0.35 mm.
Hand PensThe hand pens use the same special ink, asused in cartridges, and delivers the same out-standing durability and print quality. They areused for additional identification and speciallabeling tasks and are available in four tipwidths of 0.25mm, 0.35mm, 0.50 mm, and 0.70mm. No ink included. Must order part35100006.
Cleaning UnitIt is an easy-to-use cleaning unit developedspecially for EK Pens. The cleaning unitenables the pens to be rinsed thoroughlywhile preventing skin contact with cleaningfluid or ink. The cleaning unit can be used forup to ten cleaning cycles. The necessary pre-cautions must be taken when disposing ofcleaning fluid, the cleaning unit can bereused.
Pen CleanerThis cleaning solution comes in easy to han-dle cartridges and is used in conjunction withthe cleaning unit. A standard pack consists oftwo pen cleaner cartridges. Cleaning can beperformed on standard refillable pens only.
AdapterThis adapter allows the user of Sharpie™Ultra Fine felt tip pens instead of standardplotter pens.
Product Color Width Order No.
EK Plotter Pen black 0.18 mm 35001018
EK Plotter Pen black 0.25 mm 35001025
EK Plotter Pen black 0.35 mm 35001035
EK Plotter Pen black 0.50 mm 35001050
EK Plotter Pen black 0.70 mm 35001070
EK Plotter Pen black 1.00 mm 35001100
EK Ink Cartridge
(5 pieces, Black, 1 ml. each) black 35100006
EK Disposable Plotter Pen black 0.25 mm 35003025
EK Disposable Plotter Pen black 0.35 mm 35003035
EK Disposable Plotter Pen-ED* black 0.18 mm 35003118
EK Disposable Plotter Pen-ED* black 0.25 mm 35003125
EK Disposable Plotter Pen-ED* black 0.35 mm 35003135
EK Disposable Plotter Pen-ED* red 0.18 mm 35003218
EK Disposable Plotter Pen-ED* red 0.25 mm 35003225
EK Disposable Plotter Pen-ED* red 0.35 mm 35003235
EK Disposable Plotter Pen-ED* green 0.18 mm 35003318
EK Disposable Plotter Pen-ED* green 0.25 mm 35003325
EK Disposable Plotter Pen-ED* green 0.35 mm 35003335
EK Disposable Plotter Pen-ED* blue 0.18 mm 35003418
EK Disposable Plotter Pen-ED* blue 0.25 mm 35003425
EK Disposable Plotter Pen-ED* blue 0.35 mm 35003435
EK Hand Pen black 0.25 mm 35002025
EK Hand Pen black 0.35 mm 35002035
EK Hand Pen black 0.50 mm 35002050
EK Hand Pen black 0.70 mm 35002070
EK Cleaning Unit (empty) 35100009
EK Pen Cleaner (2 pieces, 2x10 ml.) 35100008
EK Cleaning Set 35100010
(includes cleaning unit and pen cleaner)
Adapter for an Utra Fine Sharpie™ 35000501
*Not for imprinting on polycarbonate material.
“tubular-nib” pens,6 sizes for black ink
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com84
Marking Systems Accessories
DisposablePen
ReÞllablePens
Pen Stand
Refrigerate pens whennot in use for long
periods of time.
Recovery and Storage StandThis stand is designed to keep the plotter pen in anupright position, when not used with the markingsystem.
The upright position allows the plotter pen to recoverand to be properly stored. It is recommended tostore plotter pens that will be idle for a few hours in adry and cool location, preferably in the refrigerator.
The recovery and storage stand accommodates easystorage and handling.
Call Altech for your free recovery and storage stand.
Cat. No. 35000100
Plotter Pen Handling and CarePlotter Pen Handling and Care
1
2
Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that isrequired for marking plastic material within the control and automation industry. Due to these special properties of the ink, theseplotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-teamplotter pen in tip top shape.
Suction Ball
Pen CleaningCLEANING UNITIt is an easy-to-use cleaning unit developed specially for reÞllable pens. The cleaning unit enablesthe pens to be rinsed thoroughly while preventing skin contact with cleaning ßuid or ink. Thecleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be takenwhen disposing of cleaning ßuid, the cleaning unit can be reused.
PEN CLEANERThis cleaning solution comes in easy to handle cartridges and is used in conjunction with thecleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performedon standard reÞllable pens only.
Cleaning Set Cat. No. 35100010
3
The "suction ball" is a helpful tool to bring a slightly cloggeddisposable or reÞllable plotter pen back to life.
The suction can unclog a slightly clogged plotter pen from thevacuum created within the "ball".
This additional tool can be very helpful in addition to the alreadyavailable cleaning kit (Cat. No. 35100010) for the reÞllable plotterpens.
5 replacement tips are included with each suction ball.
Cat. No. 35100013
Description Part No.
AltechAltech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 34902081Altech MT 5 - MT 15 34902001Altech Group marker G1, G2, G4 34902080
ABB / EntrelecABB Entrelec universal - RC/RCT quarter size 34902063ABB Entrelec RC 510A, 610A, 810A 34902114ABB Entrelec RC 510B, 610B, 810B” 34902102ABB Entrelec RB-RBP 5-12 34902086ABB Entrelec BA 5-50 34902100ABB Entrelec PIB 34902101ABB Entrelec RCCV 34902038ABB Entrelec BS / ILS / ILS-H 34902106Set of sticky pads ( 8 pcs) for RC/RCT 34910000
Allen Bradley /WoertzAllen Bradley UniversalW4 SERIES OLD ABWORTZ & S.S. 34902046Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal (M5X8) 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001
Conta ClipSB5, SB6 BSTR10.12 34902002SB8/10 34902003
PhoenixPhoenix Contact ZBM 34902039Phoenix Contact ZB 34902047Phoenix Contact ZBFM 34902049Phoenix Contact ZBF, ZBN 34900050Phoenix Contact BNZ 34902051Phoenix Contact BN-ZB 34902052Phoenix Contact SS-ZB 34902053Phoenix Contact LBHZ 34902054Phoenix Contact PAB 34902055Phoenix Contact GPE 34902071Phoenix Contact GPE 34902106
WagoWAGOWMB 4/4,2/5 34902041WAGOWSB 4 34902074WAGOWSB 5/5,2 34902075WAGOWSB mini 34902076WAGO Group marker carrier 34902078WAGO Marking Strip 34902087WAGO Marker tags 34902094WAGOWTB 34902096WAGOWCB 34902097WAGOWMB inline 34902098WAGO 210-345 34902106Set of sticky pads (12 pcs) forTop Job (Marking Strip) 34910002
Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001
WielandWieland Universal 34902043Wieland BZ/WKF 1,5 04.243.2053.0 34902047Wieland BZ/WKF 1,5/10 Z4.243.2053.0 34902049Wieland Steierform 6 x 15, 10 x 20 34902106
VE500 and CMPS 500 Engraving Fixtures
EK-TEAMUniversal engraving and plot support plate half size (A4) 34902106Universal engraving and plot support plate full size (A3) 34902107Universal engraving and plot support plate 30x100 ninefold 34902115Universal engraving and plot support plate 60x100 fourfold 34902116Universal engraving and plot support plate 90x100 threefold 34902117
CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLEContact Altech for Pricing (not in Price Book)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 85
Marking Systems VP500 and CMPS 500 Fixtures
To put the finishing touch on yourapplication, we offer an extensiveselection of useful accessories tobuild and install DIN Rail terminalblock assemblies and to facilitatefactory and field wiring.
Accessories include end stops, endplates and partitions. Also offeredare DIN Rails, ferrules, jumpersand more. From design to commis-sioning and operation, Altechaccessories help you do the jobbetter.
We’ve tried to make the selectionof accessories as easy as possible.The most common accessories arelisted together with their orderinginformation on each terminal blockpage in this catalog.
Terminal BlockAccessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com66
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 67
ACCESORIESAltech accessories add the finishing touches to your terminalblock assemblies. End Stops prevent terminal blocks or othercomponents and devices from moving laterally on the rail.
End Plates close off the last terminal in a series, a vital func-tion, since sectional terminal blocks are supplied with one sideopen. Isolation partitions provide visual separation of terminalgroups, as well as electrical isolation between terminals of dif-ferent potentials.
INTERCONNECTIONIn addition, Altech offers a wide choice of both Internal andExternal Jumpers to minimize wiring time and reduce installa-tion cost. Available in standard 2, 3, 4 and 10 pole configura-tions, or custom multipole jumpers. Our internal jumpers screwdirectly into terminal block busbars.
External jumpers are available in straight-comb styles. Theymay be used for terminal blocks without internal jumpering pro-visions or in combination with internal jumpers.
MOUNTINGDIN Mounting Rails are internationally standardized and avail-able in 35mm, 32mm and 15mm sizes, with or without perfora-tions. These also accommodate a wide variety of control com-ponents such as circuit breakers, timers, motor starters, relays,switches, etc. The 15mm rail with miniature blocks is usedwhen space is at a premium.
MARKINGTAGSMarking Tags make DIN Rail assemblies easier to wireand facilitate troubleshooting. Altech’s extensive termi-nal block marking system includes standard or customprinted push on tags in a variety of sizes for circuitidentification.
Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com68
AltechTERMINAL BLOCKACCESORIES Isolation Partition
Separator Plate
Internal Jumper
End Plate
End Stop
DIN 35 mmMounting Rail
DIN 35-15 mmMounting Rail
DIN 32 mmMounting Rail
Isolated Internal Jumper
Shorting Screw
Shorting Sleeve
Current Bar
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 69
End Stop
MarkingTag
External Jumper
Support Bracket
SampleTerminal Block Assemblyshowing all accessories
48mm(1.89in)
M6 18mm(.71in)
Ø7mm (.28in)
60mm (2.36in)
74mm (2.91in)74mm(2.98 in.)
52mm(2.05 in.)
M6
18mm(.71in.)
H
Slot 6x15mm(.24x.59 in.)
Ø6mm(.24 in.)
DIN35 DIN35
Type
PerforatedSteel
UnperforatedSteel
Cat. No. Length Std. Pk.
2511120 2m 202511120/1M 1m 40
2511110 2m 202511110/1M 1m 40
Type
PerforatedSteel
UnperforatedSteel
Cat. No. Length Std. Pk.
CA701-15/S-2M 2m 10CA701-15/S 1m 20
CA701-15-2M 2m 10CA701-15 1m 20
DIN Mounting RailsAltech DIN Rails comply with DIN50045, 50022 and 50035 Standards.DIN Rails have been acceptedthroughout the world, allowing thedesigner to mount a wide variety ofcontrol components, devices, termi-nal blocks, etc. on the same rail. Theuse of DIN Rails enhances designcapabilities, saves space and reduceslabor.
Standard rails are made of steel withzinc plating and chromate passivationand are available in various configu-rations.
DIN Rails are available in 35mm (7.5and 15mm deep), 32mm and 15mmwidths and are supplied in 1 m (3'3")and 2 m (6’6”) lengths. Upon requestthey can be cut to custom lengths andpunched with holes or perforations.
• 35mm, 32mm, 15mm• Perforated or unperforated• Rail material is steel with electrolyt-ic zinc plating
CA603 TSTWSupport BracketsSupport Brackets elevate DIN Railsaway from the panel to facilitatecomponent mounting and toincrease wiring access. Angled brack-ets tilt the rail by 35° to improve visi-bility. Straight brackets are availablein three heights for optimum posi-tioning of the rail.
Brackets mount with 2 screws to anypanel or flat surface and have tappedcenter holes for rail mounting.Bracket material is steel, zinc platedyellow chromated.
Height
1“2”3”
Cat. No. Std. Pk. CA603 25
Suitable for all mounting rails
Cat. No. Std. Pk.
CA703 25CA803 25CA903 25
Complete with rail mounting hardware:including one screw & one locknut
35 mm x7.5 mm deep
35 mm x15 mm deep
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com70
18 18
Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 71
DIN32 DIN15
MH2.5
Type
PerforatedSteel
UnperforatedSteel
Cat. No. Length Std. Pk.
2511160 2m 102511160/1M 1m 20
2511150 2m 102511150/1M 1m 20
Type
PerforatedSteel
Cat. No. Length Std. Pk.
CA601/S 1m 50
35 mm x15 mm deep
15 mm x5.5 mm deep
18
Cat. No. Jumper for Std. Pk.
MH2.5 CTS2.5U-N 1
MH4
Cat. No. Jumper for Std. Pk.
MH4 CTS4U-N 1
Mounting HandleMounting handle is used for mounting10 terminal blocks on a DIN rail, thussaving consideral time. Speciallydesigned pins in the mounting handlegrips the terminal blocks when pressedagainst entry.
Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com72
End StopsEnd Stops prevent terminalblocks and other DIN Rail mountcomponents and devices frommoving laterally on the rail.Theyare available in polyamide 6.6and metal configurations for35mm, 32mm, and 15mm DINrails. CA102 and CA202 are largeendstops for heavy duty appli-cations. CA103 is a screwlessendstop and snaps on to theDIN rail.
Spacer / SeparatorCASP is a DIN Rail mountablespacer generally used for circuitseparation.
DIN RailMounting FootCMTB-35 is used to assemblecomponents on a DIN rail.Comes with pre-punched holes.
• Support bracket for DIN railmounting parts
• Hole Qty x dia., 4x4.3mm,2x5.5mm
CA602CA702 CA802
Material:Polyamide 6.6
DimensionsH x L xW:20 x 28 x 8 mm
Cat. No. Std. Pk.
CA602 50
Suitable for:15 mmDIN Rails
Material:Polyamide 6.6
DimensionsH x L xW:34 x 44 x 9 mm
Cat. No. Std. Pk.
CA702 50
Suitable for:32 and 35 mm
DIN Rails
CA102 CA202
Material:Polyamide 6.6
DimensionsH x L xW:46 x 50 x 9 mm
Cat. No. Std. Pk.
CA102 50
Suitable for:32 and 35 mm
DIN Rails
Material:Polyamide 6.6
DimensionsH x L xW:44.5 x 50 x 9.5 mm
Cat. No. Std. Pk.
CA202 50
Suitable for:35 mmDIN Rails
Material:Polyamide 6.6
DimensionsH x L xW:32 x 45 x 8 mm
Cat. No. Std. Pk.
CA802 50
Suitable for:35 mmDIN Rails
Material:Steel
DimensionsH x L xW:25 x 22.5 x 11.5 mm
Cat. No. Std. Pk.
CA502 50
Suitable for:32 mmDIN Rails
Material:Steel
DimensionsH x L xW:27 x 39.5 x 16 mm
Cat. No. Std. Pk.
CA302 50
Suitable for:35x7.5mmDIN Rails
Material:Polyamide
DimensionsH x L xW:41 x 35 x 6 mm
Cat. No. Std. Pk.
CA103 50
Suitable for:35 mmDIN Rails
Material:Steel
DimensionsH x L xW:27 x 39.5 x 16 mm
Cat. No. Std. Pk.
CA402 50
Suitable for:35x15 mmDIN Rails
Material:Polyamide 6.6
DimensionsH x L xW:54 x 55.5 x 6 mm
Cat. No. Std. Pk.
CDL4USP 50
Suitable for:All
DIN Rails
Material:Polyamide 6.6
DimensionsH x L xW:
18 x 58 x 18 mm
Cat. No. Std. Pk.
CMTB-35 50
Suitable for:Mounting Foot for35 mm DIN rails
Material:Polyamide 6.6
DimensionsH x L xW:29 x 43 x 8 mm
Cat. No. Std. Pk.
CASP 50
Suitable for:All
DIN Rails
CASP
CA502CA302 CA402CA103
CMTB-35 CDL4USP
Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 73
Group IdentificationGMH6, GMH7 & GMH8
To be mounted directly on Din Rails (GMH6 & GMH7). Asticker / paper needs to be inserted in the slot which iscovered by a transparent plastic sheet.
Terminal Block Accessories
Group Marker,shown imprinted andattached to CA 702.Blank and customprinting available.Cat. No. MTG1
END PLATESEnd PlatesEnd plates are used tocover the open side of sec-tional DIN Rail mount ter-minal blocks. They shouldbe used at the end of anassembly of identical termi-nal blocks or wheneverthere is a change in thephysical size of the terminalblock.
• Material: polyamide 6.6• Standard color: gray
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com74
Cat. No. Std. Dimensions Suitable for:Pk. (H x L xW)
EP2.5/4UN 50 32 x 39 x 1.5 CTS2.5UN/4UN/CTT2.5UK/T/J/EEP6/10U 50 31 x 42.5 x 1.5 CTS6U/CTS10UEP25U 50 40 x 48 x 2 CTS25UEP35 50 43 x 50 x 1.5 CTS35UEPCMC1-2 50 35.5 x 46.5 x 2.5 CMC1-2EPCMC2-2 50 40.5 x 65 x 2.5 CMC2-2EPCDL4U 50 43 x 55 x 2.4 CDL4U/CDL4U(I.S)/ CDL4U(E) SeriesEPODL4U 50 49 x 68 x 5.5 ODL4U/ODL4UA(Front Side)EP1ODL4U 50 24 x 68 x 3 ODL4U/ODL4UA(Back Side)EPCTL2.5U 50 55.5 x 84 x 1.5 CTL2.5U/2.5UL/2.5U(I.S)EPCTL2.5UH 50 55.5 x 61 x 1.5 CTL2.5UH/2.5UH(L)/2.5UH(I.S)D2EPCMT4 50 22.5 x 27 x 1.5 CMT4/CMT4S/CMT4SUEPCMB4 50 27 x 27 x 7 CMB4EPCSFL4U 50 28 x 55.5 x 1.6 CSFL4U/4U(L)/CSDL4UEPCSFL6U 50 42.5 x 36 x 1.5 CSFL6U/CSDL6UEPCAFL4U 25 32 x 72 x 1.5 CAFL4U/4UL/4UNEPDDFL4U 25 49 x 87.6 x 3 DDFL4U/4ULR/4U(E)/4U(E)LREPCDTTU 50 41 x 63 x 3 CDTTU/CDTTUSHEPCKT4U 50 30.5 x 46.5 x 2.5 CKT4UEPCGT4U 50 40.5 x 43 x1 CGT4UEPCTC4U 50 34.5 x 47 x 2.5 CTC4UEPCSTSN5U 50 31 x 50 x 1.5 CSTSN4U/N5U/N6U/B4U/B5UEPSTH4 50 39.5 x 46 x 1.5 STH4EPSTH4DT 50 37.5 x 86 x 1.5 STH4DT / STH4DTSHEPCSC2.5T 50 23 x 58 x 1.5 CSC2.5T/CSCG2.5TEPCSC4T 50 28 x 65 x 1.5 CSC4T/CSCG4TEPCSC6T 50 32 x 72 x 2 CSC6T/CSCG6TEPCSC10T 50 37.5 x 75 x 1.5 CSC10T/CSCG10TEPCSC16T 50 82 x 38 x 1.5 CSC16T/CSCG16TEPCSCP2.5T(L&R) 25 27.5 x 35 x 5 CSCP2.5T/CSCP2.5T2EPCSC2.5T1-2 50 27 x 74 x 1.5 CSC2.5T1-2EPCSC2.5T2-2 50 25 x 90 x 1.5 CSC2.5T2-2/CSC2.5T/4(E)D3EPCSC4T1-2 50 28.5 x 84.5 x 1.5 CSC4T1-2EPCSC4T2-2 50 28.5 x 105 x 1.5 CSC4T2-2EPCSC6T1-2 50 94 x 30 x 1.5 CSC6T1-2EPAS2.5 50 35 x 54 x 1.5 AS2.5, 2.5/3, 2.5/4, AGT2.5, 2.5/3, 2.5/4EPAS4 50 27.5 x 61 x 1.5 AS4, 4/3, 4/4, AGT4, 4/3, 4/4EPAS6 50 33.5 x 74 x 1.5 AS6, 6/3, AGT6, 6/3EPASF4 50 37 x 86 x 1.5 ASF4/ASF4LEPADL2.5 50 43.5 x 80 x 1.5 ADL2.5/ADL2.5(E)D1/D2
Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 75
PARTITIONSIsolation PartitionsIsolation partitions provideseparation between termi-nal blocks with differentpotentials. When used forDC power applications,voltages of up to ± 600V DCcan be used on either sideof the isolation partition.They also provide visualseparation between groupsof blocks.
• Material: polyamide 6.6• Standard color: gray
Separator PlatesUsed for electrical separa-tion of adjacent jumpers.They can be inserted afterthe terminal blocks havebeen assembled on DINrail. There is no loss ofwidth.
Protective Cover /Side Holding Plates
For protection against dust andshock, transparent protectivecover can be installed abovethe terminal block assemblywith the aid of side/holdingplates. The side holding platescan be fitted on 35 mm and 32mm Din rails. These platesshould be backed by standardend stops.
SEPARATOR PLATES
CTSPC CSP1
150 mm
For all Rail MountingTerminals Mounting Accessoriesfor CTSPC
Assmebled Block installedwith Protective Cover
Cat. No. Std. Dimensions Suitable for:Pk. (H x L xW)
PP2.5/4UN 50 37 x 44 x 1.6 CTS2.5UN/4UN/CTT2.5UK/T/J/EPP6/10U 50 37.5 x 56.5 x 1.5 CTS6U/CTS10UPP25U 50 46.5 x 62 x 1.5 CTS25UPP25UN 50 42.5 x 62 x 1 CTS25UNPP35U 50 50 x 64.5 x 1.5 CTS35UPP35UN 50 50 x 64.5 x 1 CTS35UNPPCMT4 50 32.5 x 37 x 1.6 CMT4/CMT4S/CMT4SUPPCSFL4U 50 42.5 x 62 x 1.5 CSFL4U/4U(L)/CSDL4UPPCSC2.5T 50 28 x 58.7 x 1.5 CSC2.5T/CSCG2.5TPPCSC4T 50 33 x 65 x 1.5 CSC4T/CSCG4TPPCSC6T 50 36.5 x 72 x 2 CSC6T/CSCG6T
Cat. No. Std. Dimensions Suitable for:Pk. (H x L xW)
SP2.5/4UN 100 17.5 x 17.4 x 1.4 CTS2.5UN/4UN/CTT2.5UK/T/J/ESP6/10U 100 15.4 x 16.2 x 1.5 CTS6U/CTS10U/16USPCDL4U 100 15.4 x 16.2 x 1.6 CDL4U/CDL4U(I.S)/ CDL4U(E) SeriesSPCMB4 100 14.5 x 12 x 1.5 CMB4
Terminal Block Accessories
INTERNAL JUMPER
1 Internal Jumpering System notavailable.
2 100 pole strip can be broken down toany number of poles desired.
Jumpering SystemThe jumpering systems bus poten-tials between terminal blocks, reduc-ing wiring time. Adjacent blocks orselective terminal blocks within anassembly can be easily interconnect-ed, leaving terminal clamps free forwiring. Purchase complete assem-blies, which are ready for installation,or select individual components tocreate custom or extra long jumpers.Jumper ampacity is lower than therated current of the respective termi-nal blocks, therefore, applied currentmust not exceed the maximum cur-rent value of the block. Internaljumpers may be used in combinationwith external jumpers to achieveadditional jumpering possibilities.
Internal Jumper AssembliesInternal Jumper Assemblies consist of aCurrent Bar, Shorting Sleeves andscrews.They install easily into the centerof the terminal block and connect to thecurrent bar. They are available as stan-dard 2, 3, 4 or 10 pole assemblies andare ready for immediate installation.Insulated internal jumpers provide shockprotection when installed on terminalblock assemblies.
External JumperExternal Jumpers bus potentialsbetween terminal blocks, reducingwiring time. Adjacent or selectedblocks within an assembly can beeasily interconnected. Jumper polesmay be removed for selectivejumpering. Jumpers are insulatedand available in 2, 3, 4 and 10 poleversions.They are made of tin platedbrass/copper.
Current BarsCurrent Bars are offered to createcustom jumper assemblies forincreased number of poles or customjumpers. Select the current bar withthe required number of poles, or fieldcut them to the required length.Theyare made of tin or nickel plated cop-per or brass.
Shorting Sleeves & ScrewsShorting Sleeves & Screws ensurereliable and mechanically safe elec-trical connections between currentbars and the terminal block currentbars. One shorting sleeve is requiredfor each jumpered terminal.They aremade of nickel plated brass.
Cat. No. Torque Std. Pk.
CA721/2 0.4 Nm 100CA721/3 100CA721/4 100CA721/10 10CA721/100 10
CA722/2 0.4 Nm 100CA722/3 100CA722/4 100CA722/10 10CA722/100 10
CA723/2 0.5 Nm 100CA723/3 50CA723/4 50CA723/10 10
CA724/2 0.5 Nm 100CA724/3 50CA724/4 50CA724/10 10
CA751/2 0.8 Nm 50CA751/3 50CA751/4 50CA751/10 10
CA725/2 0.8 Nm 50CA725/3 20CA725/4 20CA725/10 10
CA726/2 0.8 Nm 50CA726/3 20CA726/4 20CA726/10 10
CA771/2 0.8 NM 50CA771/3 20CA771/4 20CA771/10 10
CA727/2 0.4 Nm 100CA727/3 100CA727/4 100CA727/10 10
CA729/2 0.5 Nm 100CA729/3 50CA729/4 50CA729/10 10
CA722/2 0.4 Nm 100CA722/3 50CA722/4 50CA722/10 20CA722/100 20
INSULATED INTERNAL JUMPER
Cat. No. Torque Std. Pk.
CA741/2 0.4 Nm 100CA741/3 100CA741/4 100CA741/10 10CA741/100 10
CA742/2 0.4 Nm 100CA742/3 100CA742/4 100CA742/10 10CA742/100 10
CA743/2 0.5 Nm 100CA743/3 50CA743/4 50CA743/10 10
CA744/2 0.5 Nm 100CA744/3 50CA744/4 50CA744/10 10
CA761/2 0.8 Nm 50CA761/3 50CA761/4 50CA761/10 10
CA745/2 0.8 Nm 50CA745/3 20CA745/4 20CA745/10 10
CA746/2 0.8 Nm 50CA746/3 20CA746/4 20CA746/10 10
CA781/2 0.8 NM 50CA781/3 20CA781/4 20CA781/10 10
CA747/2 0.4 Nm 100CA747/3 100CA747/4 100CA747/10 10
CA749/2 0.5 Nm 100CA749/3 50CA749/4 50CA749/10 10
Terminal Series Poles
CTS2.5UN 234101002
CTS4UN 2CMC1-2 3CMC2-2 4CTS4UTM 10CKT4U 1002
10 (breakable)
CTS6U 2CDTTU1 3CDTTU-SH1 4CSDL6U1 100CSFL6U1
CTS10U 23410
CTS16U 23410
CTS25U 23410
CTS35U 23410
CTS35UN* 23410
CMT4 2CMT4S 3CMB4 4CDL4U 10CDL4U(I.S) 1002
ODL4U 10 (breakable)CDL4UTM
DDFL4U 2DDFL4U(E) 3DDDL4U 4CSFL4U1 10CSFL4U(L)1CSDL4U
CAFL4U 2CAFL4U(L)1 3
410
CTL2.5U 2CTL2.5UH 3CTL2.5UL 4CTL2.5UHL 10CTL2.5U(I.S) 1002
10 (breakable)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com76
Screw Clamp Terminal Block Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 77
EXTERNAL JUMPER
Cat. No. Torque Std. Pk.
CA717/2 0.4 Nm 100CA717/3 100CA717/4 100CA717/10 20
CA713/2 0.5 Nm 100CA713/3 100CA713/4 100CA713/10 20
CA710/2 0.8 Nm 100CA710/3 50CA710/4 50CA710/10 20
CA718/2 0.8 Nm 100CA718/3 50CA718/4 50CA718/10 20
CA714/2 0.5 Nm 100CA714/3 100CA714/4 100CA714/10 20
CA711/2 0.8 Nm 100CA711/3 50CA711/4 50CA711/10 20
CA716/2 0.8 Nm 50CA716/3 50CA716/4 50CA716/10 20
CA715/2 0.4 Nm 100CA715/3 100CA715/4 100CA715/10 20
CURRENT BAR
Cat. No. Std. Pk.
CA703/01 100CA704/01 100CA705/01 100CA731/10 100CA731/100 10
CA703/1 100CA704/1 100CA705/1 100CA732/10 10CA732/100 100
CA703/2 100CA704/2 100CA705/2 100CA733/10 100
CA703/3 100CA704/3 100CA705/3 100CA734/10 100
CA703/8 100CA704/8 100CA705/8 100CA739/10 100
CA703/4 100CA704/4 100CA705/4 100CA735/10 100
CA703/5 100CA704/5 100CA705/5 100CA736/10 100
CA703/10 100CA704/10 100CA705/10 100CA770/10 100
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/100 10CA732/10-A 100
CA703/6 100CA704/6 100CA705/6 100CA737/10 100
CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/100 10CA732/10-A 100
SHORTING SLEEVE & SCREWS
Cat. No. Torque Std. Pk.
CA707/S/Q/01 0.4 Nm 100
CA707/S/Q/01 0.4 Nm 100
CA707/S/Q/1 0.5 Nm 100
CA707/S/Q/1 0.5 Nm 100
CA707/S/Q/5 0.8 Nm 100
CA707/S/Q/2 0.8 Nm 100
CA707/S/Q/2 0.8 Nm 100
CA707/S/Q/2 0.8 Nm 100
CA707/S/Q 0.4 Nm 100
CA707/S/Q/3 0.5 Nm 100
CA707/S/Q/01 0.4 Nm 100
Screw Clamp Terminal Block Accessories
Cat. No. Std. Pk.
CA801/1 100CA801/2 100CA801/3 100CA801/4 100CA801/1 100CA801/1 100CA801/2 100CA801/2 100CA801/3 100CA803/1 100CA803/1 100CA801/1 100CA801/7 100
Terminal
CSC2.5TCSC4TCSC6TCSC10TCSC2.5T1-2CSC2.5T2-2CSC4T1-2CSC4T2-2CSC6T1-2CSCP2.5TCSCP2.5T2ADL2.5ASF4
Cat. No. Std. Pk.
CA801/1-3 100CA801/2-3 100CA801/3-3 100
CA801/1-3 100CA801/1-3 100CA801/2-3 100CA801/2-3 100CA801/3-3 100
CA801/1-3 100
Cat. No. Std. Pk.
CA901/1 100CA901/2 100CA901/3 100
CA901/1 100CA901/1 100CA901/2 100CA901/2 100CA901/3 100
CA901/1 100
Wire Type Jumper For adjacent jumperingFor alternate jumpering
ADJACENT JUMPERALTERNATE JUMPER WIRETYPE JUMPER
Step DownJumpersUsed for jumperingdifferent size blocks.
Terminal
CSC6T –CSC4T
CSC6T –CSC2.5T
CSC4T –CSC2.5T
Cat. No. Std. Pk.
CA901/4 100
CA901/5 100
CA901/6 100
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com78
Spring Clamp Accessories
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 79
Terminal Block Accessories
Cat. Std. Pk. DimsNo. Strips Tags H W
MT2 10 100 4.9 5.8
MT3 20 100 5.0 10.0
MT4 10 100 5.0 4.8
MT5 10 100 9.4 4.5
MT6 10 100 9.4 5.5
MT8 10 100 10.4 7.3
MT9 10 100 10.3 8.7
MT9F 10 10 10.3 90.0
MT10 20 100 10.4 9.4
MT12 20 100 10.4 11.3
MT15 20 100 10.4 14.3
MT20 20 100 4.9 20
MT25 20 100 4.9 25
Cat. Std. Pk. DimsNo. Strips Tags H W
MT2/V 10 100 4.9 5.8
MT3/V 20 100 5.0 10.0
MT4/V 10 100 5.0 4.8
MT5/V 10 100 9.4 4.5
MT6/V 10 100 9.4 5.5
MT8/V 10 100 10.4 7.3
MT9/V 10 100 10.3 8.7
MT9F/V 10 10 10.3 90.0
MT10/V 20 100 10.4 9.4
MT12/V 20 100 10.4 11.3
MT15/V 20 100 10.4 14.3
MT20/V 20 100 4.9 20
MT25/V 20 100 4.9 25
Cat. Std. Pk. DimsNo. Strips Tags H W
MT2/H 10 100 4.9 5.8
MT3/H 20 100 5.0 10.0
MT4/H 10 100 5.0 4.8
MT5/H 10 100 9.4 4.5
MT6/H 10 100 9.4 5.5
MT8/H 10 100 10.4 7.3
MT9/H 10 100 10.3 8.7
MT9F/H 10 10 10.3 90.0
MT10/H 20 100 10.4 9.4
MT12/H 20 100 10.4 11.3
MT15/H 20 100 10.4 14.3
MT20/H 20 100 4.9 20
MT25/H 20 100 4.9 25
Consecutive Digits(Specify decade)Nos. 1-10, 11-20, etc. up to 100 *Nos. 101-110, etc. up to 999 *
Consecutive Digits(Specify decade)Nos. 1-10, 11-20, etc. up to 100Nos. 101-110, etc. up to 999
Identical Characters(Specify digits, characters)Nos. 1, 2, 3 etc. up to 999 *Characters A, B.up to Z,
Symbols +, -, *
Group Marker,shown imprinted andattached to CA 702.Blank and customprinting available.Cat. No. MTG1
BLANK MARKINGTAGSMarking TagsThe cost effective MTmarking system providesquick and accurate identifi-cation. MT Push-OnMarking Tags fit all AltechDIN Rail mount and panelmount terminal blocks.They can be inserted indi-vidually or as strips of 10tags on terminal blockassemblies for quick andeasy marking.
MT Marking Tags are sup-plied blank for custommarking or they can beordered with a horizontalor vertical imprint. Thestandard tag color is whitewith black imprint. Tagscan be ordered with up to3 characters each. Imprintscan be either consecutiveor identical characters. MTtags, catalog numbersMT2-MT8 are supplied inpacks of identical strips, 10tags per strip. Catalognumbers MT10-MT15 aresupplied in packs of identi-cal strips, 5 tags per strip.
Group marker MTG1 isused for group identifica-tion and can be fixed onthe end stop CA702.
When ordering specifystrip marking as a suffix;i.e. MT2/H-1-10.
Warning Labels
These 5 position warninglabels can be mounted ontop of 8 mm TerminalBlocks. Besides givingvisual identification, it alsomakes an entire DIN RailTerminal Block assemblycompletely shock proof.SWL6 warning labels aresuitable for CTS6U,CMDB6 and CDB6 seriesTerminal Blocks.
VERTICAL MARKINGTAGSHORIZONTAL MARKINGTAGS
Material:Polyamide 6.6
DimensionsH x L xW:
4 x 39.5 x 27 mm
Cat. No. Std. Pk.
SWL6 50
Suitable for: All DIN Rails
SWL6
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com80
Marking Systems
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 81
Marking Systems
• Identifiers for connectors, wires, cables and equipment• Cable ties, shrink tubing, labels and signs of different
sizes and materials, as well as customer-specific items.• Size: 14.9”x7.5”x1.77”• Weight: 6.6 lbs.
SCRIBERVS 210Scriber VS210
TThe VS200 base unit is a stand-aloneplotting system with an integral keyboardand display screen. The marker fixture,plotter pen, and the memory cassettehave to be inserted in the base unit tomake it operational. The base unit comesin an aluminum carrying case andincludes the memory cassette and thepower supply. A manual is available inEnglish and Spanish.
The VS 200 can be used to produce labelsof all types, with its fixture changeable ina matter of seconds.
The Vario VS 200 makes labeling easy. Themenu-driven program guides you quicklyand easily through all the steps.
It can be used at any time and in anyplace. Easily transported in its specialcase, the battery-operated (battery packsold separately) VS 200 can be operatedprecisely where you need it. The spaciouscase provides enough room for the exten-sive accessories.
Plotter VP 500
The VP 500 base unit is an auxiliary plotterand has to be connected to a PC via a par-allel port or USB connection. It is a highspeed plotting device and enables plottingof different markers in one setting. Themarker fixture and the plotter pen have tobe inserted before commencing the plot-ting operation. The base unit is primarilycontrolled through a PC with the help ofVario Sign software. Manual available inEnglish and Spanish.
The special design of the VP 500 enables itto hold different markers from variousmanufacturers at the same time. It is alsopossible to write on relatively large mark-ers with a maximum height 14 mm.
Fixtures
Fixtures are required for alignment ofmarkers with respect to the plotter pen.Different marker fixtures can be mountedon the plotter bed of the VP 500 at thesame time thereby reducing set up times.Fixtures for different markers from variousmanufacturers like Altech, Allen Bradley,Connectwell, ContaClip, Entrelec,Weidmuller, Phoenix Contact, PTR,Wieland, Wago, Murrplastik, Partex, SESSterling, etc. are available. For more infor-mation on ordering fixtures please contactAltech.
BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxxMEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000
Ordering Information
CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008
VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx ** See page 85.
Fixtures &MemoryCassette
Battery Pack Plotter Pen,Ink Cartridge
Fixtures Plotter Pen,Ink Cartridge
Vario Sign
PLOTTERVP 500CMPS 500 PLOTTER PACKAGE
• Identifiers for connectors, wires, cablesand equipment
• Cable ties, shrink tubing, labels and signsof different sizes and materials, as well ascustomer-specific items.
• Size: 26”x18”x4.9”
• CMPS plotter• Size: 17”x18”x4.9”• Tag Sizes: MT2, MT3, MT4, MT5, MT6,
MT8, MT9, MT10, MT12, MT15, MT20, MT25• CMPS software with cable• 2 fixtures for tags MT5-MT15
(MT9 sold separately)• 1 fixture for tags MT2 and MT25• 2 disposable pens
Ordering Information
Engraver VE500
The engraving unit was specificallydesigned to be used with the VP500 amdCMPS 500 plotters. Changing back andforth between the pen-plotter and theengraver is easy. The engraver is meantto engrave plastic signs on double sidedmaterial, pre-cut or blank sheets, for leg-end plates, push button inlays, etc. Theengraver is programmed by the VarioSignsoftware for ease of use and design flexi-bility.
Engraving Needles
These engraving needles are to be usedwith the VE500 engraver. They have a 15°angle and are available in 6 tip widths oras a complete set.
Vacuum Cleaner Bag
Replacement bags for the VE500engraver’s vacuum cleaner
ENGRAVERVE500
VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040
Ordering Information
VACUUM CLEANER BAG
VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000
Ordering Information
ENGRAVING NEEDLE
Product Width Order No.Engraving Needle 0.20mm 35010003Engraving Needle 0.30mm 35010002Engraving Needle 0.40mm 35010001Engraving Needle 0.50mm 35010000Engraving Needle 0.70mm 35010004Engraving Needle 1.00mm 35010005Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm) 35010006Engraving Needle(0.20 mm cutter stainless steel) 35012033
Ordering Information
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com82
Marking Systems
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 83
Marking Systems Accessories
Plotter PensThese “tubular-nib” pens are suitable for VarioScriber VS 200, Vario Plotter VP 500 and all cur-rent labeling and identification systems withHP penholders. They are available in six tipwidths identified by body color - 0.18 mm, 0.25mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00 mm;ink cartridge not supplied with pen. Specialvariants for other systems are available onrequest. Specially designed pre-filled felt-tippens are available in a set of 4 colors (black,blue, red and green) and 2 sizes - 0.3 and 0.7mm.
Ink CartridgesThese are easy to insert “tubular-nib” pen car-tridges containing special black ink suitable formarking, identifying and labeling various plas-tics. It is fast drying, smudge-proof, fade resist-ant, and resistant to chemicals when used onsuitable plastic materials.
Disposable PensThe disposable pens use the same special inkas used in the ink cartridges. They deliver thesame outstanding durability and print quality asthe standard plotter pens with the convenienceof a disposable pen. These pre-filled pensallow for fast, efficient and cost effective print-ing without refilling ink or cleaning. They areavailable in two tip widths, 0.25 mm and 0.35mm.
Hand PensThe hand pens use the same special ink, asused in cartridges, and delivers the same out-standing durability and print quality. They areused for additional identification and speciallabeling tasks and are available in four tipwidths of 0.25mm, 0.35mm, 0.50 mm, and 0.70mm. No ink included. Must order part 35100006.
Cleaning UnitIt is an easy-to-use cleaning unit developedspecially for EK Pens. The cleaning unitenables the pens to be rinsed thoroughly whilepreventing skin contact with cleaning fluid orink. The cleaning unit can be used for up to tencleaning cycles. The necessary precautionsmust be taken when disposing of cleaning fluid,the cleaning unit can be reused.
Pen CleanerThis cleaning solution comes in easy to handlecartridges and is used in conjunction with thecleaning unit. A standard pack consists of twopen cleaner cartridges. Cleaning can be per-formed on standard refillable pens only.
AdapterThis adapter allows the user of Sharpie™ UltraFine felt tip pens instead of standard plotterpens.
Product Width Order No.
EK Plotter Pen 0.18 mm 35001018
EK Plotter Pen 0.25 mm 35001025
EK Plotter Pen 0.35 mm 35001035
EK Plotter Pen 0.50 mm 35001050
EK Plotter Pen 0.70 mm 35001070
EK Plotter Pen 1.00 mm 35001100
EK Ink Cartridge
(5 pieces, Black, 1 ml. each) 35100006
EK Felt-tip Pen-Set (white tip) 0.30 mm 35000005
EK Felt-tip Pen-Set (yellow tip) 0.70 mm 35000010
EK Disposable Plotter Pen 0.25 mm 35003025
EK Disposable Plotter Pen 0.35 mm 35003035
EK Hand Pen 0.25 mm 35002025
EK Hand Pen 0.35 mm 35002035
EK Hand Pen 0.50 mm 35002050
EK Hand Pen 0.70 mm 35002070
EK Cleaning Unit (empty) 35100009
EK Pen Cleaner (2 pieces, 2x10 ml.) 35100008
EK Cleaning Set 35100010
(includes cleaning unit and pen cleaner)
Adapter for an Utra Fine Sharpie™ 35000501
“tubular-nib” pens,6 sizes for black ink
felt-tip pens,2 sizes, 4 colors
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com84
Marking Systems Accessories
DisposablePen
ReÞllablePens
Pen Stand
Refrigerate pens whennot in use for long
periods of time.
Recovery and Storage StandThis stand is designed to keep the plotter pen in anupright position, when not used with the markingsystem.
The upright position allows the plotter pen to recoverand to be properly stored. It is recommended tostore plotter pens that will be idle for a few hours in adry and cool location, preferably in the refrigerator.
The recovery and storage stand accommodates easystorage and handling.
Call Altech for your free recovery and storage stand.
Cat. No. 35000100
Plotter Pen Handling and CarePlotter Pen Handling and Care
1
2
Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that isrequired for marking plastic material within the control and automation industry. Due to these special properties of the ink, theseplotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-teamplotter pen in tip top shape.
Suction Ball
Pen CleaningCLEANING UNITIt is an easy-to-use cleaning unit developed specially for reÞllable pens. The cleaning unit enablesthe pens to be rinsed thoroughly while preventing skin contact with cleaning ßuid or ink. Thecleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be takenwhen disposing of cleaning ßuid, the cleaning unit can be reused.
PEN CLEANERThis cleaning solution comes in easy to handle cartridges and is used in conjunction with thecleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performedon standard reÞllable pens only.
Cleaning Set Cat. No. 35100010
3
The "suction ball" is a helpful tool to bring a slightly cloggeddisposable or reÞllable plotter pen back to life.
The suction can unclog a slightly clogged plotter pen from thevacuum created within the "ball".
This additional tool can be very helpful in addition to the alreadyavailable cleaning kit (Cat. No. 35100010) for the reÞllable plotterpens.
5 replacement tips are included with each suction ball.
Cat. No. 35100013
Description Part No.
AltechAltech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 34902081Altech MT 5 - MT 15 34902001Altech Group marker G1, G2, G4 34902080
ABB / EntrelecABB Entrelec universal - RC/RCT quarter size 34902063ABB Entrelec RC 510A, 610A, 810A 34902114ABB Entrelec RC 510B, 610B, 810B” 34902102ABB Entrelec RB-RBP 5-12 34902086ABB Entrelec BA 5-50 34902100ABB Entrelec PIB 34902101ABB Entrelec RCCV 34902038ABB Entrelec BS / ILS / ILS-H 34902106Set of sticky pads ( 8 pcs) for RC/RCT 34910000
Allen Bradley /WoertzAllen Bradley UniversalW4 SERIES OLD ABWORTZ & S.S. 34902046Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal (M5X8) 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001
Conta ClipSB5, SB6 BSTR10.12 34902002SB8/10 34902003
PhoenixPhoenix Contact ZBM 34902039Phoenix Contact ZB 34902047Phoenix Contact ZBFM 34902049Phoenix Contact ZBF, ZBN 34900050Phoenix Contact BNZ 34902051Phoenix Contact BN-ZB 34902052Phoenix Contact SS-ZB 34902053Phoenix Contact LBHZ 34902054Phoenix Contact PAB 34902055Phoenix Contact GPE 34902071Phoenix Contact GPE 34902106
WagoWAGOWMB 4/4,2/5 34902041WAGOWSB 4 34902074WAGOWSB 5/5,2 34902075WAGOWSB mini 34902076WAGO Group marker carrier 34902078WAGO Marking Strip 34902087WAGO Marker tags 34902094WAGOWTB 34902096WAGOWCB 34902097WAGOWMB inline 34902098WAGO 210-345 34902106Set of sticky pads (12 pcs) forTop Job (Marking Strip) 34910002
Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001
WielandWieland Universal 34902043Wieland BZ/WKF 1,5 04.243.2053.0 34902047Wieland BZ/WKF 1,5/10 Z4.243.2053.0 34902049Wieland Steierform 6 x 15, 10 x 20 34902106
VE500 and CMPS 500 Engraving Fixtures
EK-TEAMUniversal engraving and plot support plate half size (A4) 34902106Universal engraving and plot support plate full size (A3) 34902107Universal engraving and plot support plate 30x100 ninefold 34902115Universal engraving and plot support plate 60x100 fourfold 34902116Universal engraving and plot support plate 90x100 threefold 34902117
CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLEContact Altech for Pricing (not in Price Book)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 85
Marking Systems VP500 and CMPS 500 Fixtures
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com86
Printed Circuit BoardWidth
TrackType High Guide (HG)
MTGTK1 73 ± 1mm (2.9 ± 0.05 in.)MTGTK2 110 ± 1mm (4.3 ± 0.05 in.)
MountingTrack Extrusion"Cut-to-Size" Formula
Extrusion Length = Printed CircuitBoard Length – 4.5mm (.175 in.)
Sizing Information
Narrow MountingTrackExtrusion and Components
Cat. No. Std. Pk.
MTGTK1/1M 5MTGTK1 5MTGTK1/1M/G 5MTGTK1/G 5
EPDR1 100EPDR1/G 100
MTGF1 100MTGF1/G 100
EPDP1 100EPDP1/G 100
EPS 200
MT2 100
1.100 1
MountingTrack1 meter, grey2 meter, grey1 meter, green*2 meter, green*
Accessories
DIN Rail Mount End Section, greyDIN Rail Mount End Section, green*
DIN Rail Mounting Foot, greyDIN Rail Mounting Foot, green*
Panel Mount End Section, greyPanel Mount End Section, green*
DIN Rail / Panel Mount End SectionScrews #4x1/2”, Phillips Pan head(2 required per end section)
MarkingTags
DIN Rail Mounting Kit(2x EPDR, 2x MTGF, 4x EPS)
MTGF1
EPDR1
EPS
MTGTK1
For PC BoardWidths 73mm (2.9 in.)
W
L
Mount standard or custom printed circuitboards in Mounting Tracks which can beconveniently DIN rail or panel mounted inyour control panel or cabinet. These are thesame tracks used for Altech interface mod-ules. We now make them available to you tohouse and protect your custom boards, etc.Tracks are easily cut to size or can beordered precut to specific lengths. They areeasily assembled from standard componentsand snap onto 35mm DIN rail or can be panelmounted.
Each track has two sets of printed circuitboard guides to accept two alternate boardwidths.
End Sections hold printed circuit boardssecurely in place and keep out foreignobjects.
MOUNTINGWhen mounting extrusions on DIN rail, ordertwo or more DIN Rail mounting feet. Thesefeet slide into grooves on the extrusion. Thenattach two DIN Rail Mount End Sectionswith help of EPS screws.
To panel mount, order two Panel Mount EndSections (and EPS screws), each with anintegral mounting flange with a 6 x 8mm (.24x .32 in.) hole slot.
If desired, tracks can be direct mountedusing double sided tape. Order two DIN railmount end sections (and EPS screws).
• Standard Lengths: 1m (3'-3") or 2m (6'-6")• Track Material: PVC• Temperature Limit:
Short Term - 80˚C (176˚F)Continuous - 70˚C (158˚F)
• End Section, Foot Material: Polyamide• Preassembled, Precut Lengths Available• Tracks Accept Standard MT2 Marking Tags
* Green color available on request.Contact Altech for more information.
PCB Mounting Tracks
PanelMount
DIN RailMount
PanelMount
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 87
aAlso applies for DIN Rail Mount Unit
Wide MountingTrackExtrusion and Components
Cat. No. Std. Pk.
MTGTK2/1M 5MTGTK2 5MTGTK2/1M/G 5MTGTK2/G 5
EPDR2 100EPDR2/G 100
MTGF2 100MTGF2/G 100
EPDP2 100EPDP2/G 100
EPS 200
MT2 100
For PC BoardWidths 110mm (4.9 in.)
W
LEPDP2
MTGTK2
PCB Mounting Tracks
DIN RailMount
73
69
16
84
2
3515
15
82
PCB MOUNTINGTRACK (73 mm)
DIN RAIL MOUNTING FOOT (73mm)
11.4
110
16
119
2
3515
15
117
PCB MOUNTINGTRACK (110 mm)
DIN RAIL MOUNTING FOOT (110mm)
11.4
Narrow Mounting Track
Wide Mounting Track
MTGF1
EPS
WALL MOUNT DIN RAIL MOUNTPANEL MOUNT
36.5 x 61.5 x 50
10 mm
Thermoplastic
3 screw clamps
125 V
15 A
Cat. No. Std. Pk.
PMRBU 1PMRGR 1PMRBA 1
SEALGASK 1
58.5 x 84 x 53.5
10 mm
Thermoplastic
3 screw clamps
125 V
15 A
Cat. No. Std. Pk.
DMRBU 1DMRGR 1DMRBA 1
SEALGASK 1
50 x 71 x 53.5
10 mm
Thermoplastic
3 screw clamps
125 V
15 A
Cat. No. Std. Pk.
WMRBU 1WMRGR 1WMRBA 1
SEALGASK 1
Features:
• DIN Rail, Panel Mount
orWall Mount
• Rating: 15A/125V AC
• Finger Protection: IP54
• Available in 3 colors.
External Dimension (HxWxL mm)
Stripping Length
Insulation Material
Type of Connection
Approvals*
Voltage Rating
Current Rating
Complete Kit:
BlueGrayBlack
Optional AccessorySealing Gasket
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com88
aAlso applies for DIN Rail Mount Unit
E154664 E154664 E154664
Receptacles
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 89
PANEL MOUNT
WALL MOUNT
DIN RAIL MOUNT
Wiring ofReceptacles1
1
1
1Optional Sealing Gasket for wet environments.
Receptacles
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com90
Altech’s Eurostrips are safe, econom-ical and meet worldwide standards.They are a cost-effective alternativeto barrier strips that require labor-intensive wire lugs and they reducethe number of electrical connectionsin circuits.
Eurostrips feature tubular screwclamps, wire protectors, and areready for immediate wire hookup.Eurostrips are ideal in small spaces,which means more room for othercomponents or reduced enclosuresize. Free float or mount them ontoany panel. They are available ineasy-to-cut 12-pole strips or pre-cut.
Feed-Through Eurostrips are suppliedwith wire protectors. Offered withflat bases or standoff feet, they aremolded of self-extinguishingpolyamide. Custom imprinting andmarking plates are available.
EUROSTRIPS®
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 91
EASY MOUNTING SAVESINSTALLATION TIMEEurostrips are mounted quickly in pan-els. Use standard screws or mountingpins, offered as accessories in this sec-tion, or leave them free floating to com-pletely eliminate mounting.
EASYCONNECTION SAVESMONEYWhat could be easier? Simply strip thewire insulation, insert the wire andtighten the screw to achieve a gas-tight,electrically efficient connection—everytime. Wire lugs are eliminated, savingmaterial cost and installation time.
EASY MODIFICATION REDUCESINVENTORYOffered in easy-to-cut 12-pole strips, theycan also be ordered precut with the requirednumber of poles. Polyamide housing canbe cut with a utility knife or hacksaw,providing flexibility to meet changingneeds. Because standard 12 pole stripscan be so easily cut to the required num-ber of poles, stocking is simplified andinventory is minimized.
RELIABLE CONNECTIONEVERY TIMEThe basis for the Eurostrip’s reliable con-nection is a precision machined tubularscrew clamp insert made from highlyconductive copper alloy which is nickelplated for maximum corrosion resist-ance. The clamping screw material is
high strength steel toprevent screw headbreakage or threaddamage. This providestrouble free opera-
tion. Screws areelectrogalva-
nized and bluechro-mated to provide cor-
rosion resistance. Optional nickel platedbrass screws may be ordered for highlycorrosive environments or marine appli-cations.
Standard Eurostrips feature stainlesssteel wire protectors. Unlike wire pro-tectors found in many competitive prod-ucts which use copper alloy materials,stainless steel has superior memorycharacteristics. Accordingly, the wireprotector will return to its original posi-tion even after repeated use. Thismeans trouble-free wire insertion andquicker reconnections.
HOUSINGSEurostrip housings are injection moldedfrom self-extinguishing polyamide 66/6,V-O molding material, possessing highdielectric strength and excellent electri-cal insulation and temperature resist-ance. Each housing has been speciallydesigned to provide creepage and clear-ance distances to achieve ratings up to600V. Choose low profile, flat basehousings for minimum clearance appli-cations (300V) or housings with mount-ing feet for maximum voltage isolation(600V).
ACCESSORIESExternal jumpers bus potentialsbetween poles on Eurostrips, eliminat-ing wire jumpers and reducing wiringtime. Isolation partition increases clear-ance between adjacent poles and pro-vides visual separation for more effi-cient wiring. Mounting pins simplifyinstallation and mounting of Eurostrips.Simply drill the mounting hole, positionand install the pin from underneath thepanel. When correct position isreached, pin will retain terminal topanel.
Identify circuits and reduce wiring mis-takes with marking plates. Order platesimprinted or blank. Position under or ontop of a Eurostrip housing.
Imprinting Eurostrips reduces wiringerrors and helps to identify circuits. UseImprinting to mark individual poleswhen high quantities are involved orcustom imprints are required.
Eurostrips®
FEED-THROUGH FLAT BASEPanel Mount
For wire-to-wire connections inHVAC, appliance, equipment,power distribution and otherindustrial applications withstrict budget and space require-ments. Easy to use double rowterminal strips are a cost-effec-tive alternative to barrier stripsor other types of terminalblocks. Simply strip the wire,insert and tighten the screw.Eurostrips feature tubular screwclamps, with wire protectors,and recessed metal parts for fin-ger protection. The stainlesssteel wire protectors exhibitexcellent memory and the mosteffective connection.
Eurostrips described on this andthe following page are availablewith a flat base for minimumclearance applications.They canbe panel mounted or left to freefloat. Offered in easy-to-cutstandard 12-pole strips, they canalso be ordered precut with therequired number of poles.
• Tubular screw clamp• Panel mount or free float• Housing material:
- Polyamide 66/6- V-O flammability
• Color: opaque white• Marking plates or factoryimprinted application
10 mm
3.6 mm
6 mm
2.5-4 mm2 24-10 AWG
400V 300 V
10 A 30 A
0.8 Nm 7.0 lb-in
Cat. No. Std. Pk.
HE4WPR/02 100HE4WPR/03 100HE4WPR/04 100HE4WPR/05 100HE4WPR/06 50HE4WPR/07 50HE4WPR/08 50HE4WPR/09 50HE4WPR/10 50HE4WPR/11 50HE4WPR/12 50
8 mm
3 mm
5 mm
1-2.5 mm2 24-12 AWG
400 V 300 V
6 A 20 A
0.5 Nm 4.4 lb-in
Cat. No. Std. Pk.
HE1WPR/02 100HE1WPR/03 100HE1WPR/04 100HE1WPR/05 100HE1WPR/06 50HE1WPR/07 50HE1WPR/08 50HE1WPR/09 50HE1WPR/10 50HE1WPR/11 50HE1WPR/12 50
HE1 HE4
Pole Spacing
Mounting Hole Diameter
Stripping Length
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
No. of Poles
23456789101112
Flat base with wire protector Flat base with wire protector
Dimensions mm
A = 8.0 H = Ø2.8B = M2.6 I = 2.8C = 5.2 J = 6.5D = 2.8 K = 6.5E = Ø3 L = 94 (12 pole)F = Ø5 M = 12.2G = 8.0 N = 16.2
Dimensions mm
A = 10.0 H = Ø3.6B = M3 I = 3.2C = 6.4 J = 8.5D = 3.5 K = 7.9E = Ø3.6 L = 117 (12 pole)F = Ø5.7 M = 14.9G = 10.0 N = 20.0
E211022 E211022
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com92
Eurostrips®
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 93
12 mm
4.2 mm
7 mm
4-6 mm2 20-10 AWG
400V 300 V
16 A 40 A
0.8 Nm 7.0 lb-in
Cat. No. Std. Pk.
HE6WPR/02 100HE6WPR/03 100HE6WPR/04 100HE6WPR/05 100HE6WPR/06 50HE6WPR/07 50HE6WPR/08 50HE6WPR/09 50HE6WPR/10 25HE6WPR/11 25HE6WPR/12 25
HE6
Flat base with wire protector
Dimensions mm
A = 12.0 H = Ø4.1B = M3.5 I = 4.0C = 7.7 J = 9.5D = 4.3 K = 8.9E = Ø4.2 L = 140 (12 pole)F = Ø6.3 M = 16.8G = 12.0 N = 22.6
15 mm
4.3 / 5.7 mm
8.5 mm
6-10 mm2 18-8 AWG
400V 300 V
25 A 50 A
1.2 Nm 10.6 lb-in
Cat. No. Std. Pk.
HE10WPR/02 50HE10WPR/03 50HE10WPR/04 50HE10WPR/05 50HE10WPR/06 25HE10WPR/07 25HE10WPR/08 25HE10WPR/09 25HE10WPR/10 10HE10WPR/11 10HE10WPR/12 10
HE10
Flat base with wire protector
Dimensions mm
A = 15.0 H = Ø5.0B = M4 I = 4.8C = 9.3 J = 11.3D = 5.7 K = 11.6E = Ø4.3/5.7 L = 175 (12 pole)F = Ø8.2 M = 21.9G = 15.0 N = 25.1
15 mm
4.3 / 5.7 mm
8.5 mm
10-16 mm2 18-6 AWG
400 V 300 V
35-63 A 63 A
2.0 Nm 17.7 lb-in
Cat. No. Std. Pk.
HE16WPR/02 50HE16WPR/03 50HE16WPR/04 50HE16WPR/05 50HE16WPR/06 25HE16WPR/07 25HE16WPR/08 25HE16WPR/09 25HE16WPR/10 10HE16WPR/11 10HE16WPR/12 10
HE16
Flat base with wire protector
Dimensions mm
A = 15.0 H = Ø5.6B = M5 I = 4.8C = 9.3 J = 11.3D = 5.7 K = 11.6E = Ø4.3/5.7 L = 175 (12 pole)F = Ø8.2 M = 21.9G = 15.0 N = 25.1
E211022 E211022 E211022
Eurostrips®
Dimensions mm
A = 8.0 I = 6.6B = M2.6 J = 6.5C = 5.2 K = 10.3D = 2.8 L = 94 (12 pole)E = Ø3 M = 16F = Ø5 N = 16.2G = 8.0 O = 10.1H = Ø2.8
Dimensions mm
A = 10.0 I = 6.7B = M3 J = 8.5C = 6.4 K = 12.1D = 3.5 L = 117 (12 pole)E = Ø3.6 M = 19.1F = Ø5.7 N = 20G = 10.0 O = 14.0H = Ø3.6
FEED-THROUGHSTANDOFF FEETPanel Mount
For wire-to-wire connections inHVAC, appliance, equipment,power distribution and otherindustrial applications withrestricted budget and spacerequirements.
Easy to use feed-through termi-nal strips are a cost-effectivealternative to barrier strips orother types of terminal blocks.Simply strip the wire, insert, andtighten the screw. Eurostripsfeature tubular screw clamps,with wire protectors, andrecessed metal parts for fingerprotection. The stainless steelwire protectors exhibit excellentmemory and the most effectiveconnection.
Eurostrips described on this andthe preceeding page are avail-able with standoff feet forincreased wiring efficiency.Theycan be panel mounted or left tofree float. Offered in easy-to-cut12-pole strips, they can also beordered precut with therequired number of poles.
• Tubular screw clamp• Panel mount or free float• Housing material:
- Polyamide 66/6- V-O flammability
• Color: opaque white• Marking plates orfactory imprinted
10 mm
3.6 mm
6 mm
2.5-4 mm2 24-10 AWG
400 V 600 V
10 A 30 A
0.8 Nm 7.0 lb-in
Cat. No. Std. Pk.
HE4HNWPR/02 100HE4HNWPR/03 100HE4HNWPR/04 100HE4HNWPR/05 100HE4HNWPR/06 50HE4HNWPR/07 50HE4HNWPR/08 50HE4HNWPR/09 50HE4HNWPR/10 50HE4HNWPR/11 50HE4HNWPR/12 50
HE1H HE4HN
Pole Spacing
Mounting Hole Diameter
Stripping Length
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
No. of Poles
23456789101112
Standoff feet with wire protector Standoff feet with wire protector
8 mm
3 mm
5 mm
1-2.5 mm2 24-12 AWG
400 V 600 V
6 A 20 A
0.5 Nm 4.4 lb-in
Cat. No. Std. Pk.
HE1HWPR/02 100HE1HWPR/03 100HE1HWPR/04 100HE1HWPR/05 100HE1HWPR/06 50HE1HWPR/07 50HE1HWPR/08 50HE1HWPR/09 50HE1HWPR/10 50HE1HWPR/11 50HE1HWPR/12 50
E211022 E211022
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com94
Eurostrips®
Dimensions mm
A = 12.0 I = 9B = M3.5 J = 9.6C = 7.7 K = 13.9D = 4.3 L = 140 (12 pole)E = Ø4.2 M = 21.8F = Ø6.3 N = 22.6G = 12.0 O = 15H = Ø4.1
Dimensions mm
A = 15.0 I = 10.7B = M5 J = 11.3C = 9.3 K = 17.5D = 5.7 L = 175 (12 pole)E = Ø4.3/5.7 M = 27.8F = Ø8.2 N = 25.1G = 15.0 O = 16H = Ø5.6
Dimensions mm
A = 15.0 I = 10.7B = M4 J = 11.3C = 9.3 K = 17.5D = 5.7 L = 175 (12 pole)E = Ø4.3/5.7 M = 27.8F = Ø8.2 N = 25.1G = 15.0 O = 16H = Ø5.0
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 95
15 mm
4.3/5.7 mm
8.5 mm
10-16 mm2 18-6 AWG
400 V 600 V
35-63 A 63 A
2.0 Nm 17.7 lb-in
Cat. No. Std. Pk.
HE16HWPR/02 40HE16HWPR/03 40HE16HWPR/04 40HE16HWPR/05 40HE16HWPR/06 20HE16HWPR/07 20HE16HWPR/08 20HE16HWPR/09 10HE16HWPR/10 10HE16HWPR/11 10HE16HWPR/12 10
12 mm
4.2 mm
7 mm
4-6 mm2 20-10 AWG
400 V 600 V
16 A 40 A
0.8 Nm 7.0 lb-in
Cat. No. Std. Pk.
HE6HWPR/02 100HE6HWPR/03 100HE6HWPR/04 100HE6HWPR/05 100HE6HWPR/06 50HE6HWPR/07 50HE6HWPR/08 50HE6HWPR/09 50HE6HWPR/10 25HE6HWPR/11 25HE6HWPR/12 25
HE6H HE10H
Standoff feet with wire protector Standoff feet with wire protector
15 mm
4.3/5.7 mm
8.5 mm
6-10 mm2 18-8 AWG
400 V 600 V
25 A 50 A
1.2 Nm 10.6 lb-in
Cat. No. Std. Pk.
HE10HWPR/02 40HE10HWPR/03 40HE10HWPR/04 40HE10HWPR/05 40HE10HWPR/06 20HE10HWPR/07 20HE10HWPR/08 20HE10HWPR/09 10HE10HWPR/10 10HE10HWPR/11 10HE10HWPR/12 10
HE16H
Standoff feet with wire protector
E211022 E211022 E211022
Eurostrips®
PLUGGABLEPanel Mount
For wire-to-wire connections inHVAC, appliance, equipment,power and other distributionapplications. Pluggable Euro-strips® speed and simplifyreplacement of subassemblies,etc. They reduce downtime andmisconnections.
Two-piece pluggable terminalstrips feature tubular screwclamps, with recessed metalparts for finger protection. Aspring loaded contact preventsinadvertant unplugging.
The headers and plugs are avail-able with flat base or standofffeet and can be panel mountedor free float. Offered in easy-tocut 12-pole strips, they can alsobe orderd precut with therequired number of poles.
• Tubular Screw Clamp• Panel Mount or Free Float• Housing material:
- Polyamide 66/6- V-O flammability
• Color: OpaqueWhite
10 mm
3.5 mm
3.6 mm
2.5-4mm2 24-10AWG
400V 300V
10A 20A
0.8Nm 7.2lb
Cat. No. Std. Pk.
HE42BU/02 100HE42BU/03 100HE42BU/04 100HE42BU/05 100HE42BU/06 50HE42BU/07 50HE42BU/08 50HE42BU/09 50HE42BU/10 50HE42BU/11 50HE42BU/12 50
HE42ST HE42BU
Pole Spacing
Mounting Hole Diameter
Stripping Length
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
No. of Poles
23456789101112
A
N LEø E D C
RM
IK
ø
P Q
J O G F
B
HDimensions mmA = 10.0 J = 15.2B = M3 K = 7.9C = 6.4 L = 117D = 3.6 M = 14.9E = Ø3.5 N = 34.4F = Ø5.7 O = 9.2G = 10.0 P = 20H = Ø3.5 Q = 14.4I = 3.2 R = 7
10 mm
3.5 mm
3.6 mm
2.5-4mm2 24-10AWG
400V 300V
10A 20A
0.8Nm 7.2lb
Cat. No. Std. Pk.
HE42ST/02 100HE42ST/03 100HE42ST/04 100HE42ST/05 100HE42ST/06 50HE42ST/07 50HE42ST/08 50HE42ST/09 50HE42ST/10 50HE42ST/11 50HE42ST/12 50
FLAT BASE
E211022 E211022
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com96
Eurostrips®
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 97
Dimensions mmA = 10.0 J = 15.2B = M3 K = 11.5C = 6.4 L = 117D = 3.6 M = 18.5E = Ø3.5 N = 34.4F = Ø5.7 O = 9.2G = 10.0 P = 20H = Ø3.5 Q = 14.4I = 6.8 R = 7
10 mm
3.5 mm
3.6 mm
2.5-4mm2 24-10AWG
400V 600V
10A 20A
0.8Nm 7.2lb
Cat. No. Std. Pk.
HE42SBU/02 100HE42SBU/03 100HE42SBU/04 100HE42SBU/05 100HE42SBU/06 50HE42SBU/07 50HE42SBU/08 50HE42SBU/09 50HE42SBU/10 50HE42SBU/11 50HE42SBU/12 50
HE42SST HE42SBU
10 mm
3.5 mm
3.6 mm
2.5-4mm2 24-10AWG
400V 600V
10A 20A
0.8Nm 7.2lb
Cat. No. Std. Pk.
HE42SST/02 100HE42SST/03 100HE42SST/04 100HE42SST/05 100HE42SST/06 50HE42SST/07 50HE42SST/08 50HE42SST/09 50HE42SST/10 50HE42SST/11 50HE42SST/12 50
STANDOFFFEET
E211022 E211022
A
N LEø E D C
RM
IK
ø
P Q
J O G F
B
H
Eurostrips®
Pole Spacing
Mounting Hole Diameter
Stripping Length
Approvals
Wire Range
Voltage Rating
Current Rating
Torque
Other Approvals
No. of Poles
23456789101112
Isolation Partition
Eurostrip
Thickness
Ordering Information
KA46
HE4HN, HE6H
3.4 mm (.134 in.)
Cat. No. Std. Pk.
HEP4/6H 5
EXTERNAL JUMPERSAccessories
Convenient options that facilitateinstallation and wire termination.
External Jumpers
Bus potentials between poleson Eurostrip Terminal Stripsreducing wiring time and elim-inating wire jumpers.
Jumper Pole positions may beremoved to provide selectivejumpering. When using exter-nal jumpers, the terminal'srated cross section is usuallyreduced one wire size. Forjumper maximum current rat-ings, refer to the correspon-ding Eurostrip IEC/VDE currentrating.
• Material: copper alloy,nickel plated
• Insulation: polyamide 6.6• Color: black.
Isolation Partitions
Isolation Partition KA providesseparation between adjacentpoles of different potentials on600V Eurostrips with standofffeet. Visual separationbetween poles is also provid-ed by an isolation partition,assisting circuit identificationand increasing wiring efficien-cy
• Material: polyamide 6.6• Color: black
ISOLATION PARTITION
External Jumper
Eurostrip
Pole Spacing
Ordering Information
HCL8 HCL10 HCL12 HCL15
HE1 HE4 HE6 HE10, HE16
8mm (.315) 10 mm (.394 in.) 12 mm (.472) 15 mm (.591 in.)
Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.
HCL8-2 100 HCL10-2 100 HCL12-2 100 HCL15-2 100HCL8-3 100 HCL10-3 100 HCL12-3 100 HCL15-3 100HCL8-4 100 HCL10-4 100 HCL12-4 100 HCL15-4 100HCL8-12 25 HCL10-12 25 HCL12-12 25 HCL15-12 25
2 pole3 pole4 pole12 pole
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com98
Eurostrips®
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 99
H IL
W
Ø
Accessories
Convenient options that facilitateinstallation and wire termination.
Mounting Pins
Speed panel mounting ofEurostrips with MountingPins. Simply match drill clear-ance hole in panel, positionEurostrip and install MountingPin through hole and intomounting hole in Eurostriphousing. Once pin passesbeyond Eurostrip housing, itautomatically expands, secur-ing housing to panel. Use twoor more mounting pins perEurostrip.
• Material: polycarbonate• Color: gray.
Marking Plates
Install Marking Plate MPunder or on top of Eurostriphousing to identify individualpole positions to increasewiring efficiency, save instal-lation time and facilitate wirehook-up, system modificationand trouble shooting. Selectblank marking plate for handmarking or imprinted.
• Material: self-extinguishingPVC
• Color: white with blackimprint.
Imprinting
Mark individual pole positionsto save installation time andfacilitate wire hook-up, sys-tem modification and troubleshooting. Choose turret mark-ing for optimum identifica-tion.To order imprinting spec-ify consecutive, identical orcustom character imprints.
• Imprints: rub-resistant,black ink.
• Set up fee applies
• 1000 piece minimum
Mounting Pins
Eurostrip
Panel Thickness
Ordering Information
H4 H6
HE4HN HE6H
0.5-1.5 mm 0.8-1.8 mm
Cat. No. Std. Pk. Cat. No. Std. Pk.
H4 50 H6 50
MARKING PLATES
Eurostrip HE4, HE4HN HE6, HE6H HE10, HE10H, HE16, HE16H
Ordering Information Cat.No. Desc. Std. Pk Cat.No. Desc. Std. Pk. Cat.No. Desc. Std. Pk.
BS24E Blank 25 BS60E Blank 25 BS1016E Blank 25BS24EM1-12 No. 1-12 25 BS60EM1-12 No. 1-12 25 BS1016EM1-12 No. 1-12 25BS24EM13-24 No. 13-24 25 BS60EM13-24 No. 13-24 25 BS1016EM13-24 No. 13-24 25
IMPRINTING
Imprint
MarkingInstruction
Ordering Example
Turret Location
Consecutive, imprint 1 through 12,Turret Location
Cat. No. Std. Pk.
HE4WPR/12i1-12 1000
Turret Location
Dimensions mm (in.)Mounting Pin Insertion Panel WidthPin Type Height (H) Length (IL) Hole Dia. (W)H4 21 12.6 4.2 8.5H6 24 14.7 5.2 11
Eurostrips®
MOUNTING PINS
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 105
InsulatedIndustry Standard
Ferrules insure reliable elec-trical connections when ter-minating stranded flexiblewire in terminal blocks, cir-cuit breakers or other con-trol devices. Insulated fer-rules prevent conductorbreakage due to bending,wire stress or vibrationwhile facilitating wire inser-tion into the terminal clamp.
Altech’s standard insulatedferrules are color coded byconductor size for conven-ient identification.
To ensure efficient ferrulecrimping, always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 98.)
• Sleeve: polypropylene• Tube: tin-plated copper
AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.
(mm2) Color Type No. mm (in.) A B C D Pk.*
24 (.25) Lt. Blue H0.25/6 2620.0 6.0(.24) 10.0 (.39) 6.0 (.24) 1.2 (.05) 2.3 (.09) 500/100
24 (.25) Lt. Blue H0.25/8 2621.0 8.0(.31) 12.0 (.47) 8.0 (.31) 1.2 (.05) 2.3 (.09) 500/100
22 (.34) Turquoise H0.34/6 2622.0 6.0(.24) 10.0 (.39) 6.0 (.24) 1.2 (.05) 2.5 (.10) 500/100
22 (.34) Turquoise H0.34/8 2623.0 8.0(.31) 12.0 (.47) 8.0 (.31) 1.2 (.05) 2.5 (.10) 500/100
20 (.50) Orange H0.50/6 2397.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.3 (.05) 2.8 (.11) 500/100
20 (.50) Orange H0.50/8 2201.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.3 (.05) 2.8 (.11) 500/100
18 (.75) White H0.75/6 2398.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.5 (.06) 3.3 (.13) 500/100
18 (.75) White H0.75/8 2202.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.5 (.06) 3.3 (.13) 500/100
18 (1.00) Yellow H1.00/6 2399.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.7 (.07) 3.5 (.14) 500/100
18 (1.00) Yellow H1.00/8 2203.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.7 (.07) 3.5 (.14) 500/100
16 (1.50) Red H1.50/8 2204.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.0 (.08) 4.0 (.16) 500/100
16 (1.50) Red H1.50/10 2400.0 10.0(.39) 16.0 (.63) 10.0 (.39) 2.0 (.08) 4.0 (.16) 500/100
16 (1.50) Red H1.50/18 2205.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.0 (.08) 4.0 (.16) 500/100
14 (2.50) Blue H2.50/8 2206.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.5 (.10) 4.7 (.19) 500/100
14 (2.50) Blue H2.50/12 2401.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.5 (.10) 4.7 (.19) 500/100
14 (2.50) Blue H2.50/18 2207.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.5 (.10) 4.7 (.19) 500/100
12 (4.00) Gray H4.00/10 2208.0 10.0(.39) 17.0 (.67) 10.0 (.39) 3.2 (.13) 5.4 (.21) 500/100
12 (4.00) Gray H4.00/12 2402.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.2 (.13) 5.4 (.21) 500/100
12 (4.00) Gray H4.00/18 2209.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.2 (.13) 5.4 (.21) 100
10 (6.00) Black H6.00/12 2210.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.9 (.15) 6.9 (.27) 100
10 (6.00) Black H6.00/18 2211.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.9 (.15) 6.9 (.27) 100
8 (10.00) Ivory H10.0/12 2212.0 12.0(.47) 22.0 (.87) 12.0 (.47) 4.9 (.19) 8.4 (.33) 100
8 (10.00) Ivory H10.0/18 2213.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 4.9 (.19) 8.4 (.33) 100
6 (16.00) Green H16.0/12 2214.0 12.0(.47) 24.0 (.94) 12.0 (.47) 6.2 (.24) 9.6 (.38) 100
6 (16.00) Green H16.0/18 2215.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 6.2 (.24) 9.6 (.38) 100
4 (25.00) Brown H25.0/18 2267.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 7.7 (.30) 12.0(.47) 50
4 (25.00) Brown H25.0/22 2272.0 22.0(.87) 36.0 (1.42) 22.0 (.87) 7.7 (.30) 12.0(.47) 50
2 (35.00) Beige H35.0/18 2276.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 8.7 (.34) 13.5(.53) 50
2 (35.00) Beige H35.0/25 2390.0 25.0(.98) 39.0 (1.54) 25.0 (.98) 8.7 (.34) 13.5(.53) 50
1 (50.00) Olive H50.0/20 2500.0 20.0(.79) 36.0 (1.42) 20.0 (.79) 10.9(.43) 16.0(.63) 50
2/0 (70.00) Yellow H70.0/21 2786.0 20.0(.79) 37.0 (1.46) 20.0 (.79) 13.4(.53) 17.0(.67) 25
3/0 (95.00) Red H95.0/25 2787.0 25.0(.98) 44.0 (1.73) 25.0 (.98) 15.4(.61) 19.0(.75) 25
4/0 (120.00) Blue H120.0/27 2788.0 27.0(1.06) 48.0 (1.89) 27.0 (1.06) 17.6(.69) 22.4(.88) 25
250MCM(150.0)Yellow H150.0/27 2789.0 32.0(1.26) 58.0 (2.28) 32.0 (1.26) 20.5(.81) 25.0(.98) 25
INDUSTRY STANDARD FERRULES
* Different standard packs are available as shown. To order the desired standard pack, please use the quantity required as a suffix to the cat. no.Example for 100 standard pack: Type H0.25/6, Cat. No. 2620.0/100
CRIMPER SELECTORGUIDESee page 109.
Ferrules
CSA Std C22.2 No. 65-93 - Wire ConnectorsCSA Std C22.2 No. 188-M1983 - Splicing Wire and Cable ConnectorsANSI/UL Std No. 486A - Wire Connectors and Soldering Lugs for Use with Copper ConductorsANSI/UL Std No. 486C - Splicing Wire Connectors220672
Tested According To:
InsulatedDIN Standard
Ferrules insure reliableelectrical connectionswhen terminating strand-ed flexible wire in termi-nal blocks, circuit breakersor other control devices.
Insulated ferrules preventconductor breakage dueto bending, wire stress orvibration while facilitatingwire insertion into the ter-minal clamp.
Altech’s DIN standard fer-rules are in compliancewith DIN requirements,making them ideal forexport applications. Theyalso have a specified colorcode convention that dif-fers from the color codeused for Altech’s industrystandard ferrules.
To ensure efficient ferrulecrimping, always selectthe smallest ferrule diam-eter that fits the wire anduse only professionalcrimping tools. (Pleaserefer to the orderingpages and the CrimperSelector Guide on page98.)
• Sleeve: polypropylene• Tube: tin plated copper
AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.
(mm2) Color Type No. mm (in.) A B C D Pk.*
20 (.50) White H0.50/6 2863.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.3 (.05) 2.8 (.11) 500/100
20 (.50) White H0.50/8 2864.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.3 (.05) 2.8 (.11) 500/100
20 (.50) White H0.50/10 2865.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.3 (.05) 2.8 (.11) 500/100
18 (.75) Gray H0.75/6 2866.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.5 (.06) 3.3 (.13) 500/100
18 (.75) Gray H0.75/8 2867.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.5 (.06) 3.3 (.13) 500/100
18 (.75) Gray H0.75/10 2868.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.5 (.06) 3.3 (.13) 500/100
18 (.75) Gray H0.75/12 2869.0 12.0(.47) 18.0 (.71) 12.0 (.47) 1.5 (.06) 3.3 (.13) 500/100
18 (1.00) Red H1.00/6 2870.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.7 (.07) 3.5 (.14) 500/100
18 (1.00) Red H1.00/8 2871.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.7 (.07) 3.5 (.14) 500/100
18 (1.00) Red H1.00/10 2872.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.7 (.07) 3.5 (.14) 500/100
18 (1.00) Red H1.00/12 2840.0 12.0(.47) 18.0 (.71) 12.0 (.47) 1.7 (.07) 3.5 (.14) 500/100
16 (1.50) Black H1.50/8 2841.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.0 (.08) 4.0 (.16) 500/100
16 (1.50) Black H1.50/10 2842.0 10.0(.39) 16.0 (.63) 10.0 (.39) 2.0 (.08) 4.0 (.16) 500/100
16 (1.50) Black H1.50/12 2843.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.0 (.08) 4.0 (.16) 500/100
16 (1.50) Black H1.50/18 2844.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.0 (.08) 4.0 (.16) 500/100
14 (2.50) Blue H2.50/8 2845.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.5 (.10) 4.7 (.19) 500/100
14 (2.50) Blue H2.50/12 2846.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.5 (.10) 4.7 (.19) 500/100
14 (2.50) Blue H2.50/18 2847.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.5 (.10) 4.7 (.19) 500/100
12 (4.00) Gray H4.00/10 2848.0 10.0(.39) 17.0 (.71) 10.0 (.39) 3.2 (.13) 5.4 (.21) 500/100
12 (4.00) Gray H4.00/12 2849.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.2 (.13) 5.4 (.21) 500/100
12 (4.00) Gray H4.00/18 2850.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.2 (.13) 5.4 (.21) 100
10 (6.00) Yellow H6.00/12 2851.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.9 (.16) 6.9 (.27) 100
10 (6.00) Yellow H6.00/18 2852.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.9 (.16) 6.9 (.27) 100
8 (10.00) Red H10.00/12 2853.0 12.0(.47) 22.0 (.87) 12.0 (.47) 4.9 (.20) 8.4 (.33) 100
8 (10.00) Red H10.00/18 2854.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 4.9 (.20) 8.4 (.33) 100
6 (16.00) Blue H16.00/12 2855.0 12.0(.47) 24.0 (.87) 12.0 (.47) 6.2 (.24) 9.6 (.38) 100
6 (16.00) Blue H16.00/18 2856.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 6.2 (.24) 9.6 (.38) 100
4 (25.00) Yellow H25.00/18 2857.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 7.7 (.30) 12.0(.47) 50
4 (25.00) Yellow H25.00/22 2858.0 22.0(.87) 36.0 (1.5) 22.0 (.87) 7.7 (.30) 12.0(.47) 50
2 (35.00) Red H35.00/18 2859.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 8.7 (.34) 13.5(.53) 50
2(35.00) Red H35.00/25 2860.0 25.0(.98) 39.0 (1.54) 25.0 (.98) 8.7 (.34) 13.5(.53) 50
1 (50.00) Blue H50.00/20 2861.0 20.0(.79) 36.0 (1.5) 20.0 (.79) 10.9(.43) 16.0(.63) 50
DIN STANDARD FERRULES
* Different standard packs are available as shown. To order the desired standard pack, please use the quantity required as a suffix to the cat. no.Example for 100 standard pack: Type H0.50/6, Cat. No. 2863.0/100
CRIMPER SELECTORGUIDESee page 109.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com106
Ferrules
CSA Std C22.2 No. 65-93 - Wire ConnectorsCSA Std C22.2 No. 188-M1983 - Splicing Wire and Cable ConnectorsANSI/UL Std No. 486A - Wire Connectors and Soldering Lugs for Use with Copper ConductorsANSI/UL Std No. 486C - Splicing Wire Connectors220672
Tested According To:
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 107
UninsulatedFerrules insure reliable elec-trical connections when ter-minating stranded flexiblewire in terminal blocks, cir-cuit breakers or other con-trol devices.
Uninsulated ferrules pre-vent wire strands from fray-ing and breaking and areextremely cost effective.Their shorter lengths anduninsulated bodies offeradvantages when makingterminations in printed cir-cuit board terminal blocksand in other terminal blockswith smaller clamps or nar-row widths.
To ensure efficient ferrulecrimping, always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 109.)
• Tube: tin plated copper
AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.(mm2) Type No. mm (in.) A B C Pk.*
20 (.50) H0.50/6 2216.0 6.0 (.24) 6.0 (.24) 1.3 (.05) 2.1 (.08) 1000/100
18 (.75) H0.75/6 2217.0 6.0 (.24) 6.0 (.24) 1.5 (.06) 2.3 (.09) 1000/100
18 (.75) H0.75/10 2218.0 10.0 (.39) 10.0 (.39) 1.5 (.06) 2.3 (.09) 1000/100
18 (1.00) H1.00/6 2219.0 6.0 (.24) 6.0 (.24) 1.7 (.07) 2.5 (.10) 1000/100
18 (1.00) H1.00/10 2220.0 10.0(.39) 10.0 (.39) 1.7 (.07) 2.5 (.10) 1000/100
16 (1.50) H1.50/7 2221.0 7.0 (.28) 7.0 (.28) 2.3 (.09) 2.8 (.11) 1000/100
16 (1.50) H1.50/10 2222.0 10.0 (.39) 10.0 (.39) 2.3 (.09) 2.8 (.11) 1000/100
14 (2.50) H2.50/7 2223.0 7.0 (.28) 7.0 (.28) 2.5 (.10) 3.4 (.13) 1000/100
14 (2.50) H2.50/12 2224.0 12.0 (.47) 12.0 (.47) 2.5 (.10) 3.4 (.13) 1000/100
12 (4.00) H4.00/9 2225.0 9.0 (.35) 9.0 (.35) 3.2 (.13) 4.0 (.16) 1000/100
12 (4.00) H4.00/12 2226.0 12.0 (.47) 12.0 (.47) 3.2 (.13) 4.0 (.16) 1000/100
10 (6.00) H6.00/12 2227.0 12.0 (.47) 12.0 (.47) 3.9 (.15) 4.7 (.19) 500/100
10 (6.00) H6.00/15 2388.0 15.0 (.59) 15.0 (.59) 3.9 (.15) 4.7 (.19) 500/100
8 (10.00) H10.00/12 2228.0 12.0 (.47) 12.0 (.47) 4.9 (.19) 5.8 (.23) 500/100
8 (10.00) H10.00/15 2389.0 15.0 (.59) 15.0 (.59) 4.9 (.19) 5.8 (.23) 500/100
8 (10.00) H10.00/18 2229.0 18.0 (.71) 18.0 (.71) 4.9 (.19) 5.8 (.23) 500/100
6 (16.00) H16.00/12 2391.0 12.0 (.47) 12.0 (.47) 6.2 (.24) 7.5 (.30) 500/100
6 (16.00) H16.00/15 2392.0 15.0 (.59) 15.0 (.59) 6.2 (.24) 7.5 (.30) 500/100
6 (16.00) H16.00/18 2393.0 18.0 (.71) 18.0 (.71) 6.2 (.24) 7.5 (.30) 100
4 (25.00) H25.00/15 2394.0 15.0 (.59) 15.0 (.59) 7.7 (.30) 9.5 (.37) 500/100
4 (25.00) H25.00/18 2395.0 18.0 (.71) 18.0 (.71) 7.7 (.30) 9.5 (.37) 100
2 (35.00) H35.00/18 2396.0 18.0 (.71) 18.0 (.71) 8.7 (.34) 11.0 (.43) 100
1 (50.00) H50.00/32 2816.0 32.0 (1.26) 32.0 (1.26) 10.9 (.43) 13.0 (.51) 100
2/0 (70.00) H70.00/25 2790.0 25.0 (0.98) 25.0 (.98) 13.3 (.52) 15.0 (.59) 100
3/0 (95.00) H95.00/32 2791.0 32.0 (1.26) 32.0 (1.26) 15.3 (.60) 17.0 (.67) 50
4/0 (120.00) H120.00/32 2792.0 32.0 (1.26) 32.0 (1.26) 17.5 (.69) 19.0 (.75) 25
250MCM(150.00) H150.00/32 2793.0 32.0 (1.26) 32.0 (1.26) 19.5 (.77) 21.0 (.83) 25
350MCM(185.00) H185.00/32 2815.0 32.0 (1.26) 32.0 (1.26) 21.2 (.83) 23.5 (.93) 25
UNINSULATED FERRULES
* Different standard packs are available as shown. To order the desired standard pack, please use the quantity required as a suffix to the cat. no.Example for 100 standard pack: Type H0.50/6, Cat. No. 2216.0/100
CRIMPER SELECTORGUIDESee page 109.
Ferrules
CSA Std C22.2 No. 65-93 - Wire ConnectorsCSA Std C22.2 No. 188-M1983 - Splicing Wire and Cable ConnectorsANSI/UL Std No. 486A - Wire Connectors and Soldering Lugs for Use with Copper ConductorsANSI/UL Std No. 486C - Splicing Wire Connectors220672
Tested According To:
AB1-S
AB2-S
Dual WireInsulatedDual Wire Ferrules havelarger diameters and spe-cial shaped sleeves thataccept two conductors ofthe same or different size.They provide an efficientconnection of multiplewires in the same terminalclamp or simplify wirejumpering between termi-nal clamps. They are colorcoded with the same con-vention as the insulatedDIN standard ferrules.
To ensure efficient ferrulecrimping always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 109.)
• Sleeve: polypropylene• Tube: tin plated copper
INSULATED FERRULESAssortment BoxHandy Assortment Boxes forconvenient dispensing andstorage of Industry and DINStandard Insulated Ferrules.Types AB1-S and AB1-D areequipped with five differentferrule sizes. Types AB2-Sand AB2-D are equipped withfour different ferrule sizes.Contents of each box is list-ed. Dimensions for industryand DIN standard insulatedferrules are listed on pages106.
DUAL WIRE FERRULES
Wires x AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.(mm2) Color Type No. mm (in.) A B C D1 D2 Pk.*
2x20 (2x.50) White H2x0.50/8 2794.0 11.0 (.43) 14.6 (.57) 8.2 (.32) 1.7 (.07) 3.0 (.12) 5.0 (.20) 500/100
2x18 (2x.75) Gray H2x0.75/8 2775.0 11.0 (.43) 14.6 (.57) 8.2 (.32) 2.0 (.08) 3.0 (.12) 5.5 (.22) 500/100
2x18 (2x.75) Gray H2x0.75/10 2795.0 13.0 (.51) 16.4 (.65) 10.0 (.39) 2.0 (.08) 3.0 (.12) 5.5 (.22) 500/100
2x18 (2x1.0) Red H2x1.00/8 2776.0 11.0 (.43) 15.4 (.61) 8.2 (.32) 2.4 (.09) 3.2 (.13) 5.8 (.23) 500/100
2x18 (2x1.0) Red H2x1.00/18 2796.0 21.0 (.83) 25.2 (.99) 18.0 (.71) 2.4 (.09) 3.2 (.13) 5.8 (.23) 500/100
2x16 (2x1.5) Black H2x1.50/8 2777.0 12.0 (.47) 15.8 (.62) 8.2 (.32) 2.6 (.10) 3.6 (.14) 6.5 (.26) 500/100
2x16 (2x1.5) Black H2x1.50/12 2797.0 16.0 (.63) 19.6 (.77) 12.0 (.47) 2.6 (.10) 3.6 (.14) 6.5 (.26) 500/100
2x14 (2x2.5) Blue H2x2.50/10 2778.0 14.0 (.55) 18.5 (.73) 10.0 (.39) 3.3 (.13) 4.5 (.18) 8.0 (.31) 500/100
2x14 (2x2.5) Blue H2x2.50/12 2798.0 17.0 (.67) 20.5 (.80) 12.0 (.47) 3.3 (.13) 4.5 (.18) 8.0 (.31) 500/100
2x12 (2x4.0) Gray H2x4.00/12 2799.0 16.0 (.63) 22.0 (.87) 12.0 (.47) 3.9 (.15) 5.2 (.20) 9.0 (.35) 100
2x10 (2x6.0) Yellow H2x6.00/12 2800.0 18.0 (.71) 23.0 (.91) 12.0 (.47) 5.0 (.20) 6.2 (.24) 11.4 (.45) 100
2x8 (2x10.0) Red H2x10.00/12 2801.0 18.0 (.71) 24.0 (.94) 12.0 (.47) 6.2 (.24) 7.6 (.30) 13.4 (.53) 100
2X6 (2x16.0) Blue H2x16.00/16 2802.0 20.0 (.79) 29.0 (1.14) 16.0 (.63) 8.9 (.35) 9.5 (.37) 17.2 (.68) 100/50
Ferrule AWG Ferrule Ferrule Ferrule Std.Qty. (mm2) Type Cat. No. Color Type Cat. No. Pk.
AB1-S Industry Standard AB1-S 2884.9 150 20 (.50) H0.50/8 2201.0 Orange100 20 (.75) H0.75/8 2202.0 Whiite100 18 (1.00) H1.00/6 2399.0 Yellow100 16 (1.50) H1.50/8 2204.0 Red50 14 (2.50) H2.50/8 2206.0 Blue
AB2-S Industry Standard AB2-S 2885.9 150 12 (.4.0) H4.00/10 2208.0 Gray20 10 (6.0) H6.00/12 2210.0 Black20 8 (10.0) H10.00/12 2212.0 Ivory10 6 (16.0) H16.00/12 2214.0 Green
AB1-D DIN Standard AB1-D 2884.0 150 20 (.50) H0.50/6 2864.0 White100 20 (.75) H0.75/8 2867.0 Gray100 18 (1.0) H1.00/8 2871.0 Red100 16 (1.5) H1.50/8 2841.0 Black50 14 (2.5) H2.50/8 2845.0 Blue
AB2-D DIN Standard AB2-D 2885.0 150 12 (4.00) H4.00/10 2848.0 Gray20 10 (6.00) H6.00/12 2851.0 Yellow20 8 (10.00) H10.00/12 2853.0 Red10 6 (16.00) H16.00/12 2855.0 Blue
* Different standard packs are available for manyferrules. To order the desired standard pack, please use the quantity required as a suffix to the Cat. No.
Example: Type H2x0.50/0,Cat. No. 2794.0/100 for a standard pack of 100
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com108
Ferrules
CSA Std C22.2 No. 65-93 - Wire ConnectorsCSA Std C22.2 No. 188-M1983 - Splicing Wire and Cable ConnectorsANSI/UL Std No. 486A - Wire Connectors and Soldering Lugs for Use with Copper ConductorsANSI/UL Std No. 486C - Splicing Wire Connectors220672
Tested According To:
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com100
TOOLS &FERRULES
To help you do the best job possiblewhen using Altech’s terminal blocks,we put together a selection of usefultools to accomplish just that. Weoffer this as a service to our cus-tomers, since some of the specialtools we offer are hard to find.
Included in this tool selection arewire strippers to safely and quicklyremove insulation from wire andcable and to speed the wire prepara-tion process; semi-automatic andhand operated crimping tools forcrimping ferrules onto wire ends. Ourlarge selection of screwdriversinclude insulated and uninsulatedstraight blade, flat tip and Phillipstypes.
All tools are made from the highestquality steels for superior perform-ance and long life. The hand toolsare manufactured to exacting speci-fications and carefully heat treatedfor maximum strength and durability.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 101
Universal Ferrule CrimperFront Conductor EntryOne die crimps a wide range of insulated and uninsulated ferrulesizes.Three Universal Ferrule Crimpers are offered to crimp differentferrule and wire size ranges up to 16mm2 (6 AWG).
• Positive ratcheting with spring return•Trapezoidal crimp geometry• Comfort grip plastic handle• Hardened steel frame, matte black
Ferrule CrimperSide Conductor EntryIndividual crimp cavities conform to industry standard insulatedand uninsulated ferrules from 25-50mm2 (4-1 AWG).
• Positive ratcheting with spring return• Emergency release•Trapezoidal crimp geometry• Comfort grip plastic handle• Hardened steel frame, matte black
Universal Ferrule Crimper Universal Ferrule CrimperUniversal Ferrule Crimper
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
E110.000 26 - 10 0.14 - 6 1
Replacement Spring Set:185140008 Handle Spring Set318001002 Rachet Spring
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
E110.005 20 - 8 0.5 - 10 1
Replacement Spring Set:185140008 Handle Spring Set318001002 Rachet Spring
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
E110.010 8 - 6 10 - 16 1
Replacement Spring Set:185140008 Handle Spring Set318001002 Rachet Spring
Ferrule Crimper Ferrule CrimperFerrule Crimper
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
E110.015 4 - 2 25 - 35 1
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
E110.020 1 50 1
Part No. Wire/ Ferrule Std.AWG mm2 Pk.
22.030 2/0-250 70 - 150 1MCM
Crimper Tools
Altech's pneumatic crimping toolsspeed the crimping process of insulat-ed or uninsulated ferrules for a widerange of wire sizes up to 8 AWG.
Altech pneumatic crimpers are simpleand easy to use. Just install the ferruleover the end of the stripped wire andinsert it into either the front or side toolopening.Then touch the actuating leveror push the footswitch pedal to initiatethe crimp cycle. Once the head closes itwill automatically reopen after crimp-ing.The resulting crimp features a com-pact trapezoidal cross section which ismechanically very strong and providesa large surface to insure a highly effi-cient electrical contact.
Crimp ferrules efficiently and economi-cally. A unique dual crimping head pro-vides convenient front or side wireentry, allowing crimping from multiplepositions.This features makes crimpingin tight places simple.
Choose either lever actuated, handheld units or hands-free footswitchoperated table top models, in two basictool sizes. Hand held models feature aflexible coil air-hose with 1/4" NPTinterchange connector for quick hook-up with a standard push-to-connectcoupler.
The table top units also include a flexi-ble coil air hose to the footswitch and a1/4" NPT interchange located on thefootswitch for one hand push-to-con-nect supply hook-up. They feature asturdy metal base with integral tableclamp and dual storage trays for quickaccess to the ferrule supply. The airrelease port on the footswitch has beenquieted with a sintered bronze airsilencer. The footswitch has a metalframe and a tough fiberglass shroud.Its spring return pedal provides forshort actuating cycles.
Optional items for the hand heldcrimper include a counterbalance formaximum control and a magnetic hold-er for storage.
• Operates on 60 - 90 psi air supply• Crimp insulated and uninsulatedferrules
• Trapezoidal crimp geometry• Flexible coil air hose with 1/4"NPT interchange
• Metal tool body and base• Hardened steel crimp head
Wire/ Ferrule Size Tool Wt.Tool AWG mm2 Type Cat. No. g (lbs.) Std. Pk.
Hand Held Crimper with Actuating Lever ACT2.5-P 22.014 430 (.95) 1Crimp Insulated Ferrules 24-14 0.25-2.5and Uninsulated Ferrules
Hand Held Crimper with Actuating Lever ACT10-P 22.015 430 (.95) 1Crimp Insulated Ferrules 12-8 4.0-10.0and Uninsulated Ferrules
Table Top Crimper with Footswitch and Storage Trays ACT2.5-T 22.016 1000 (2.20) 1Crimp Insulated Ferrules 24-14 0.25-2.5and Uninsulated Ferrules
Table Top Crimper with Footswitch and Storage Trays ACT10-P 22.017 1000 (2.20) 1Crimp Insulated Ferrules 12-8 4.0-10.0and Uninsulated Ferrules
Magnetic Mounting Holder ACT-DXP 22.018 --- 1for hand held pneumatic crimpers
Counterbalance CT-DUP 22.019 --- 1for hand held pneumatic crimpers
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com102
Pneumatic Crimping Tool
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com98
Key:
ACT10-P
E110.015
E110.020
ACT2.5T-P 2
ACT10T-P
ACT2.5P 2
Wire SizeAWG Cr
imper Type
Ferrule Sizemm2
GFCF
CRIMPER STYLES
VISE MOUNTFERRULECRIMPER
C R I M P E R S E L E C T O R G U I D EFerrule and Wire Size by Crimper Type
E110.000
E110.005
E110.010
UNIVERSAL FERRULECRIMPER
PNEUMATIC FERRULECRIMPER
Use this Selector Guide to determine ferrule and wire sizes which can be crimped. Refer to ordering pages 94-97for additional selection and ordering information.
1. Determine the wire size(s) to be used.
2. Select the appropriate ferrule size(s).1
3. Based on the ferrule size, choose the crimper type appropriate for use. 4. Select the crimper style best suited for your application.
Dual Wire FerrulesE110.000 crimper covers 2x20 to 2x12 AWG dual wire ferrulesE110.010 crimper covers 2x10 to 2x8 AWG dual wire ferrulesE110.015 crimper covers 2x6 AWG dual wire ferrules
= Multi-Cavity RangeX = Individual Cavity
1 To insure efficient ferrule crimping, always select the smallest ferrule diameter that fits the wire.2 Insulated ferrule/wire size range is shown, uninsulated ferrule range is 16-14 AWG (1.50 - 2.5mm2).
26 .14
24 .25
22 .34
20 .50
20 .75
18 1.00
16 1.50
14 2.50
12 4.00
10 6.00
8 10.00
6 16.00
4 25.00
2 35.00
1 50.00
2/0 70.00
3/0 95.00
4/0 120.00
250MCM 150.00
X XX XX X
XX
XXXXX
99Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
CONVERSION TABLES
DEGREES CELSIUS VERSUS DEGREES FAHRENHEIT
°C °F °C °F °C °F °C °F °C °F °C °F °C °F °C °F °C °F
-80 -112.0 -20 –4.0 5 41.0 30 86.0 55 131.0 80 176.0 105 221.0 130 266.0 200 392-70 -94.0 -19 –2.2 6 42.8 31 87.8 56 132.8 81 177.8 106 222.8 131 267.8 210 410-60 -65.0 -18 –0.4 7 44.6 32 89.6 57 134.6 82 179.6 107 224.6 132 269.6 220 428-50 -58.0 -17 +1.4 8 46.4 33 91.4 58 136.4 83 181.4 108 226.4 133 271.4 230 446-45 -49.1 -16 3.2 9 48.2 34 93.2 59 138.2 84 183.2 109 228.2 134 273.2 240 464
-40 -40.0 -15 5.0 10 50.0 35 95.0 60 140.0 85 185.0 110 230.0 135 275.0 250 482-39 -38.2 -14 6.8 11 51.8 36 96.8 61 141.8 86 186.8 111 231.8 136 276.8 300 572-38 -36.4 -13 8.6 12 53.6 37 98.6 62 143.6 87 188.6 112 233.6 137 278.6 350 662-37 -34.6 -12 10.4 13 55.4 38 100.4 63 145.4 88 189.4 113 235.4 138 280.4 400 752-36 -32.8 -11 12.2 14 57.2 39 102.2 64 147.2 89 192.2 114 237.2 139 282.2 500 932
-35 -31.0 -10 14.0 15 59.0 40 104.0 65 149.0 90 194.0 115 239.0 140 284.0 600 1112-34 -29.2 -9 15.8 16 60.8 41 105.8 66 150.8 91 195.8 116 240.8 141 285.8 700 1292-33 -27.4 -8 17.6 17 62.6 42 107.6 67 152.6 92 197.6 117 242.6 142 287.6 800 1472-32 -25.6 -7 19.4 18 64.4 43 109.4 68 154.4 93 199.4 118 244.4 143 289.4 900 1652-31 -23.8 -6 21.2 19 66.2 44 111.2 69 156.2 94 201.2 119 246.2 144 291.2 1000 1832
-30 -22.0 -5 23.0 20 68.0 45 113.0 70 158.0 95 203.0 120 248.0 145 293.0 1100 2012-29 -22.0 -4 24.8 21 69.8 46 114.8 71 159.8 96 204.8 121 249.8 146 294.8 1200 2192-28 -18.4 -3 26.6 22 71.6 47 116.6 72 161.6 97 206.6 122 251.6 147 296.6 1300 2372-27 -16.6 -2 28.4 23 73.4 48 118.4 73 163.4 98 208.4 123 253.4 148 298.4 1400 2552-26 -14.8 -1 30.2 24 75.2 49 120.2 74 165.2 99 210.2 124 255.2 149 300.2 1500 2732
-25 -13.0 0 32.0 25 77.0 50 122.0 75 167.0 100 212.0 125 257.0 150 302.0 1600 2912-24 -11.2 1 33.8 26 78.8 51 123.8 76 168.8 101 213.8 126 258.8 160 320.0 1700 3092-23 -9.4 2 35.6 27 80.6 52 125.6 77 170.6 102 215.6 127 260.6 170 338.0 1800 3272-22 -7.6 3 37.4 28 82.4 53 127.4 78 172.4 103 217.4 128 262.4 180 356.0 1900 3452-21 -5.8 4 39.2 29 84.2 54 129.2 79 174.2 104 219.2 129 264.2 190 374.0 2000 3632
Conversion Formula °F = 9/5°C + 32° °C = 5/9(°F–32°)
Metric Cross- American Wire Gauge Metric Cross- American Wire GaugeSectional Areas a Sections Areas a
Cross-Sectional Equivalent AWG or MCM Cross-Sectional Equivalent AWG or MCMArea Metric Area Area Metric Areamm2 mm2 mm2 mm2
0.5190.6530.823
1.041.31
1.652.08
2.62
3.314.175.26
6.638.37
10.5513.3016.77
20 AWG1918
1716
1514
13
121110
98
765
21.1526.6733.63
85.03
107.20126.64152.00177.35202.71253.35
380.00
506.71
0.50
0.75
1.5
2.5
4.0
6.0
10.0
16.0
4 AWG32
3/0
4/0250 MCM300350400500
750
1000
25.0
35.0
50.0
70.0
95.0
120.0
150.0
185.0
240.0
300.0400.0
500.0625.0
aAs per IEC Publ. 228
Lengthinch [in.] x 25.4 =millimetersmillimeters [mm] x 0.03937 =inchesmeters [m] x 3.281 =feetmiles [mi] x 1.609 =kilometerskilometers [km] x 0.6214 =miles
TorqueNewtonmeter [Nm] x 0.738=lb-ftlb-ft x 1.356 =Nmlb-in x 0.113 =Nmoz-in x 0.0071 =Nm
Powerkilowatt [kW] x 1.341 =hphp x 0.7457 =kW
Moment of Inertia (WR2)lb-ft2 x 0.042 =kgm2
kilogrammeter2 23.720 =lb-ft2[kgm2]
Weight Mass and ForceNewton [N] x 0.2248 =poundkilogram [kg] x 2.205 =poundspound [lb] x 4.448 =Npound [lb] x 0.4536 =kg
67.432/0
53.48 1/0
42.41 1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com100
oooooooooooooooooooooooooooooooooooooooooooooooo
Total Length (3)
Internal Jumpers
External Jumpers (AQ)
??
?
?
?
?
?
? 6.3mm (.25 in.)
Ground Blk CGT4U 1 6 6
Feed Through CTS25U 1 12 12
End Plate EP25U 1 2 2
Feed Through CTS6U 2 8 16
End Plate EP6/10U 1 1.5 1.5
Feed Through CTS4U-N/R 1 6 6
Feed Through CTS4U-N/W 1 6 6
Feed Through CTS4U-N/BU 1 6 6
Feed Through CTS4U-N/BL 1 6 6
Feed Through CTS4U-N 5 6 30
Disconnect CKT4U 1 6 6
Fuse Block CSFL4U(L) 1 8 8
Double Level Block CDL4U 1 6 6
End Plate EPCDL4U 1 2.5 2.5
End Stop CA702 1 9 9
External Jumper 2P CA714/2 1 - -
Internal Jumper 3P CA722/3 1 - -
Push on Marker - -
123
125
22
67
89
13
45
3911
125
22
67
89
13
45
3911
163
173
Bill of Material
Component Cat. No. Qty. Width Ext.Description Ea. Width
(mm) (mm)
?
?
?
25mm(.98 in.)
a Other slot and hole configurations available, please consult Altech.b Based on standard 8 mm slots.
Mounting Centers (4)
Indicate the specific positions of all terminal blocks and accessories selected. Include terminal markings, external andinternal jumpers.
A = Total
••
EXAMPLE
Std. Slots a - 6.3 x 8mm(.25 x .32 in.)
Marking
?
?
25mm(.98 in.)
?
DIN Rail Ordering InformationCat. No. (3) Length (mm)
2511120 173
DIN Rail Length Calculation mm(1) Std. Mounting Allowance at Ends = 25mm x 2 50
(2) Total Width of Components = A 123
(3) Total Length (Rail) = (1) + (2) 173
(4) Mounting Centers = (3) – 10mm b 163
DIN RAIL ASSEMBLY WORKSHEET
Company: _______________________________________________
Address: ________________________________________________
_________________________________________________
Phone: (____)________________ FAX: (____) _________________
Contact:_________________________________________________
135 East Front St.
York, PA 17405
Doug Jones, EE
B.L. Products Company
717 555-8086 717 555-8087
CGT4U
CTS25U
EP25U
CTS6U
CTS6U
EP6/10U
CTS4U-N/R
CTS4U-N/W
CTS4U-N/BU
CTS4U-N/BL
CTS4U-N
CTS4U-N
CTS4U-N
CTS4U-N
CTS4U-N
CKT4U
CSFL4U(L)
CDL4U
EPCDL4U
CA702
101Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
oooooooooooooooooooooooooooooooooooooooooooooooo
Total Length (3)
Internal Jumpers (Q)
External Jumpers (AQ)
??
?
?
?
?
?
? 6.3mm (.25 in.)
Bill of Material
Component Cat. No. Qty. Width Ext.Description Ea. Width
(mm) (mm)
?
?
?
25mm(.98 in.)
a Other slot and hole configurations available, please consult Altech.b Based on standard 8 mm slots.
Mounting Centers (4)
Indicate the specific positions of all terminal blocks and accessories selected. Include terminal markings, external andinternal jumpers.
A = Total
Std. Slots a - 6.3 x 8mm(.25 x .32 in.)
Marking
?
?
25mm(.98 in.)
?
DIN Rail Ordering InformationCat. No. (3) Length (mm)
DIN Rail Length Calculation mm
DIN RAIL ASSEMBLY WORKSHEET
DIN Rail Length Calculation mm(1) Std. Mounting Allowance at Ends = 25mm x 2
(2) Total Width of Components = A
(3) Total Length (Rail) = (1) + (2)
(4) Mounting Centers = (3) – 10mm b
Company: _______________________________________________
Address: ________________________________________________
_________________________________________________
Phone: (____)________________ FAX: (____) _________________
Contact:_________________________________________________
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com102
IMPRINT SCHEDULE FOR CUSTOM MARKING TAGS*
Cat. No. Tag DimensionsHorizontal Imprint W x H MT 2/H- XX 4.9 x 5.8MT 3/H- XX 5.0 x 10.0 MT 4/H- XX 5.0 x 4.8MT 5/H- XX 9.4 x 4.5MT 6/H- XX 9.4 x 5.5MT 8/H- XX 10.4 x 7.3MT 9/H- XX 10.3 x 8.7MT 10/H- XX 10.4 x 9.4MT 12/H- XX 10.4 x 11.3MT 15/H- XX 10.4 x 14.3MT 20/H- XX 4.9 x 20MT 25/H- XX 4.9 x 25
Ordering Instructions
1) Indicate Tag Type (Use separate sheet for each Tag Typeordered).2) List imprint sequence for each strip. (Please use Typewriter)3) Indicate strip quantity for each strip.4) Indicate total strip quantity.5) Mail or FAX form with Purchase Order to Altech.
* SSEETT--UUPP FFEEEE AAPPPPLLIIEESS TTOO CCUUSSTTOOMM IIMMPPRRIINNTTSS..
A
B
C
D
E
F
G
H
I
J
1
Strip Qty.
A
B
C
D
E
F
G
H
I
J
2
Strip Qty.
A
B
C
D
E
F
G
H
I
J
3
Strip Qty.
A
B
C
D
E
F
G
H
I
J
4
Strip Qty.
A
B
C
D
E
F
G
H
I
J
5
Strip Qty.
A
B
C
D
E
F
G
H
I
J
6
Strip Qty.
Strip Qty.
A B C D E F G H I J
L
w
X917
233 HORIZONTALX917
240
X917
232
X917
241
A B C D E F G H I J
L
w
VERTICAL49T6019
49T6020
49T6027
49T6028
Cat. No. Tag DimensionsVertical Imprint W x H MT 2/V- XX 4.9 x 5.8MT 3/V- XX 5.0 x 10.0 MT 4/V- XX 5.0 x 4.8MT 5/V- XX 9.4 x 4.5MT 6/V- XX 9.4 x 5.5MT 8/V- XX 10.4 x 7.3MT 9/V- XX 10.3 x 8.7MT 10/V- XX 10.4 x 9.4MT 12/V- XX 10.4 x 11.3MT 15/V- XX 10.4 x 14.3MT 20/V- XX 4.9 x 20MT 25/V- XX 4.9 x 25
Company: _______________________________________________
Address: ________________________________________________
_________________________________________________
Phone: (____)________________ FAX: (____) _________________
Contact:_________________________________________________