1

TECHNICAL MANUAL - AlphaAnnounce

AlphaAnnounce PA System 2007 TYP 3 - HAV

2

Table of Contents

Table of Contents ....................................................................................................... 2

Key to numbers ......................................................................................................... 3

Module 1 – ................................................................................................................ 4

Module 1 ................................................................................................................... 5

Module 1 ................................................................................................................... 6

Module 2 and 3 .......................................................................................................... 7

Module 4 and 5 .......................................................................................................... 8

Module 6 ................................................................................................................... 9

Module 7 and 8 ......................................................................................................... 10

Module 9 and 10 ....................................................................................................... 11

Module 11 and 12 ..................................................................................................... 12

Module 13 and 14 ..................................................................................................... 13

3

Key to numbers

Module Description

1 Alarm call master panel

2 100 V Relay card

3 100 V / Signal Relay card

4 Amplifier monitoring

5 100V Relay card / General Alarm

6 Digital I/O card

7 Telephone interface / external control input

8 DAC Digital Announce Card

9 230V power supply / Battery switch

10 Back-up microphone

11 Back-up push button panel

12 DAC Digital Announce Card for the back-up system

13 Digital power amplifier 100V - 250 W / 500 W

14 Digital power amplifier 100V - 250 W / 500 W

4

Module 1 – Alarm call master panel (System status)

PC RS232 - PC connection for programming purpose

SYS Err. - General alarm. There is a system error

BUS act. - Data bus active. Data transfer is taking place

DSP1 - Led is on when microphone panel 1 is connected and ready to use

- Led blinks when microphone panel 1 is not connected or defective

DSP2 - Led is on when microphone panel 2 is connected and ready to use

- Led blinks when microphone panel 2 is not connected or defective

DSP3 - Led is on when microphone panel 3 is connected and ready to use

- Led blinks when microphone panel 3 is not connected or defective

DSP4 - Led is on when microphone panel 4 is connected and ready to use

- Led blinks when microphone panel 4 is not connected or defective

DSP5 - Led is on when microphone panel 5 is connected and ready to use

- Led blinks when microphone panel is not connected or defective

DSP6 - Led is on when microphone panel 6 is connected and ready to use

- Led blinks when microphone panel 6 is not connected or defective

5

Module 1 – Alarm call signal control ( Programme - Music)

Input 1 - Led is on when music input 1 is active

Input 2 - Led is on when music input 2 is active

Input 3 - Led is on when music input 3 is active

IN1 - Volume / Level music input 1

IN2 - Volume / Level music input 2

IN3 - Volume / Level music input 3

Level - Master volume of all music signals

LF - Low frequency – increase / decrease 80Hz +/- 12 dB

HF - High frequency – increase / decrease 8,000Hz +/- 12 dB

Level[dB] - Sound level indicator

6

Module 1 - Alarm call signal control – (Call / Alarm)

Level - Volume level adjustment of announcement

This control has no purpose for alarm signals from the DAC (module 8)

The volume of the alarm signal can be adjusted via the DAC (module 8)

LF - Low frequency - increase / decrease 80Hz +/- 12 dB

HF - High frequency - increase / decrease 8,000Hz +/- 12 dB

Level[dB] - Sound level indicator

ACTIVE - Led is on if one of the microphone panels is active or if there is an alarm

7

Module 2 and 3 – Relay card (Module 2 en 3)

Module 2

Rel. active LED 1 - LED on: Zone 1 active

Rel. active LED 2 - LED on: Zone 2 active

Rel. active LED 3 - LED on: Zone 3 active

Rel. active LED 4 - LED on: Zone 4 active

Rel. active LED 5 - LED on: Zone 5 active

Rel. active LED 6 - LED on: Zone 6 active

Module 3

Rel. active LED 1 - LED on: Zone 7 active

Rel. active LED 2 - LED on: Zone 8 active

Rel. active LED 3 - LED on: Alarm 1 active

Rel. active LED 4 - LED on: Alarm 2 active

Rel. active LED 5 - LED on: Alarm 3 active

Rel. active LED 6 - LED on: Alarm output active

8

Module 4 and 5 - Amplifier monitor (Module 4) – Relay card (Module 5)

Module 4

AMP1 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

AMP2 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

AMP3 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

AMP4 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

AMP5 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

AMP6 - Green LED on = Amplifier OK. Red LED on = Amplifier defective

Module 5

Rel. active LED 1 - Amplifier 1 defective. The back-up amplifier will take over

Rel. active LED 2 - Amplifier 2 defective. The back-up amplifier will take over

Rel. active LED 3 - Amplifier 3 defective. The back-up amplifier will take over

Rel. active LED 4 - Amplifier 4 defective. The back-up amplifier will take over

Rel. active LED 5 - Amplifier 5 defective. The back-up amplifier will take over

Rel. active LED 6 - Amplifier 6 defective. The back-up amplifier will take over

9

Module 6 - Digital I/O Card - DIO16MS

Output 1 –8 (Red Led)

• Output led 1 on Zone 1 activated by Master System (Module 1)

Output led 1 blinking Zone 1 activated by back-up System (Module 10&11)

• Output led 2 on Zone 2 activated by Master System (Module 1)

Output led 2 blinking Zone 2 activated by back-up System (Module 10&11)

• Output led 3 on Zone 3 activated by Master System (Module 1)

Output led 3 blinking Zone 3 activated by back-up System (Module 10&11)

• Output led 4 on Zone 4 activated by Master System (Module 1)

Output led 4 blinking Zone 4 activated by back-up System (Module 10&11)

• Output led 5 on Zone 5 activated by Master System (Module 1)

Output led 5 blinking Zone 5 activated by back-up System (Module 10&11)

• Output led 6 on Zone 6 activated by Master System (Module 1)

Output led 6 blinking Zone 6 activated by back-up System (Module 10&11)

• Output led 7 on Zone 7 activated by Master System (Module 1)

Output led 7 blinking Zone 7 activated by back-up System (Module 10&11)

• Output led 8 on Zone 8 activated by Master System (Module 1)

Output led 8 blinking Zone 8 activated by back-up System (Module 10&11)

• Output led 12 on System Error active

• Output led 15 on System in use

Input LED 1 on Error from back-up system active (Module 10&11)

Input LED 2 on The back-up system (Module 10&11) is in use

In-Output LED 16 blinking Digital I/O Card DIO16MS (Module 5) active – OK

10

Module 7 and 8 – Telephone interface / signal input (Module 7) - DAC (Module 8)

Module 7

Pwr.[data] Led Blinks during active data transmission and Power OK

Error Led On: System failure

C/A Preset Led On: External Call input on this module is active

Prg. Preset Not in use

Level 1 Volume adjustment of telephone announcements

Level 2 Not in use

Level 3 Not in use

Rs 232 PC Interface / (Only for service)

Module 8

Power[data] Led Blinks during active data transmission and Power OK

Play Led On: message is playing

Blinking: testing message

Error Led On: SD card error / failure

Level 1 Volume Alarm 1

Level 2 Volume Alarm 2

Level 3 Volume Alarm 3

Level 4 Volume pre-announcement tone

Level 5 Not in use

Level 6 Not in use

11

Module 9 and 10 – Power supply (Module 9) - back-up microphone (Module 10)

Module 9

P Led on Power OK

E Led on Power failure / No battery connected

S Led on Standby (Not in use)

Module 10

Back-up microphone. This microphone has priority over the Master system.

By pushing the call button an announcement can be made in all zones at once.

This function will remain when the Master system fails.

12

Module 11 and 12 - Back-up push button field (Module 11) - Back-up DAC (Module 12)

.

Module 11

Push button 1 Activates Alarm 1

Push button 2 Activates Alarm 2

Push button 3 Activates Alarm 3

Push button 4 Stops an active alarm.

The back-up system always has priority over the master system.

Module 12

Power[data] Led On: Power OK

Play Led On: Message is playing

Blinking: Testing message

Error Led On: Sd card failure

Level 1 Volume alarm 1 (back-up system level)

Level 2 Volume alarm 2 (back-up system level)

Level 3 Volume alarm 3 (back-up system level)

Level 4 Not in use

Level 5 Not in use

Level 6 Not in use

13

Module 13 and 14 - Amplifier

Module 13 + 14

PS OK Led Power OK

Bat Error Led Battery failure

BAT active Led Amplifier operating on battery

SPK CON Loudspeaker wiring OK

Standby Led Not in use

GND Fault Earth loop on loudspeaker output determined

Error Amplifier failure / Overload

-30-20-10 dB Led Output Level indicator

Clip Led on Overload, entry level too high