Upload
salman-iqbal
View
212
Download
0
Embed Size (px)
DESCRIPTION
alm
Citation preview
By Engnr.Asad Iqbal Jamal
Power Cube:S. NoALM CardALM NameALM Color CodeALM CODE
1ALM1UPEU EXT1TOCPMUAC OFF ALMWhite Orang/Orange65101
2ALM2DC LOW ALMWhite Green/Green65108
3ALM3RECT FAULT ALWhite Blue/Blue65125
4ALM4SMOKE ALMWhite Brown/Brown65103
5ALM5UPEU EXT0 TOCPMUDOOR ALMWhite Orange/Orange65104
6ALM6HIGH TEMP ALMWhite Green/Green65105
7DO_2UPEU EXT0 TOHPMU DO2GEN FAULT ALMWhite Blue/Blue65109
8DI_5BATT ROOMTOHPMU DO5BATT DOOR ALMWhite Orange/Orange65104
9EXT0(UEIU)UEIU EXT0TOCivil ALM BOX(8,9)TOWER LIGHT ALMWhite Orange/Orange65107
DO2: (White Blue/Blue) is From BBU (UPEU - EXT- ALM-0) to HPMU (D0-2)DO5: Battery Door Alarm (White Orange/White) is connected here.UEIU EXT1 White blue/Blue is connected in battery room for Battery AC.UEIU EXT0 White Orange/Orange is connected for Tower light
Mini Shelter:S. NoALM LocationCardALM NameALM Color CodeALM Code
1ALM1UPEUEXT1MAJ PWR FAILUREWhite Orang/Orange65110
2ALM2DC LOW ALMWhite Green/Green65108
3ALM3RECT FAULT ALMWhite Blue/Blue65125
4ALM4EMPTY CONNECTEDWhite Brown/Brown
5ALM5UPEU EXT0SMOKE ALMWhite Orang/Orange65103
6ALM6HIGH TEMP ALMWhite Green/Green65105
7ALM7DOOR ALMWhite Blue/Blue65104
8ALM8AC OFFWhite Brown/Brown65101
9EXT0(UEIU)UEIUTOWER LIGHTWhite Orang/Orange65107
Power Cube:Power Cube Alarm Configuration:There are two parts two alarm configuration (1) HPMU (2) CMPU.HPMU Port Configuration: Here we can configure only two alarms 1.Genset Fault, 2. Battery Door. Battery Door is already configured no need to configure while Genset Fault can be configured on HPMU DO2 as,Step 1 >Go to>SettingStep 2 >Go to>Put Password as (0)Step 3 >Go to>Alarm SettingStep 4 >Go to>Dry NodeStep 5 >Go to>Adio Backup DO2 (Make DO2 SDG Fail) So Now DO2 is configured for Genset Fault ALM.CPMU Port Configuration:AC OFF, DC LOW, HIGH TEMP, RECTIFIRE FAULT, SMOKE can be configured on CPMU as,Step 1 >Go to>SettingStep 2 >Go to>Alarm SettingStep 3 >Go to>Relay RelateStep 4 >Go to>Alarm (Configured each Alarm on desired port.
Power Cube Alarm Generation or Checking.1. AC OFF: Turn off the AC breaker AC Alarm will be appeared. If check the cable connection in the battery door upper most corner right side. For clearing this alarm turn on the AC braker.2. DC LOW: This is the most difficult alarm to generate. It can be generated in many ways but on simple way is given as,
Step 1 >Go to HPMU> SettingStep 2 >Go to>Put Password as (0)Step 3 >Go to>Critical PointStep 4 >Go to>Battery Under Volta:( Make it Maximum or 51.5V)Step 5 >Go to CPMU>SettingStep 6 >Go to>Battery SettingStep 7 >Go to>ChargeStep 8 >Go to>Boost (Make It maximum or 57.5)Step 9 >Go to>Click on Back Button and Press DC SettingStep 10 >Go to>Under Volt (Make it Maximum or 51.5)You will found DC low Alarm. It can remove by putting the original values back in the HPMU and CPMU.Reminder: This Alarm can be Generated Only and Only when voltage is greater than 53.3V and keep the Genset off for generation.3. RECTIFIRE FAULT: Take a cable tie and stop the fan in any rectifier module for 2minutes, a beef sound will produce and alarm will appear. For clearing remove the cable tie after a minute beef will stop and alarm will be clear.4. SMOKE ALARM: Produce the Smoke near to the smoke sensor. Smoke alarm will appear. For clearing this alarm remove the green connector back to smoke sensor and then insert back.5. DOOR ALARM: Open the Door alarm will appear and closed the door alarm will disappear.6. HIGH TEMP:Step 1>Go to> SettingStep 2>Go to>Ambient Temp Setting (Make it 25 or less alarm will appear. To clear it back make the value again the original.
7. Genset Fault: Stop the Generator and put the AC main braker turn off. It will appear and do its vice versa to clear this alarm.8. Genset Running: Make only this alarm polarity high in the power cube, then start the Genset alarm will appear and stop alarm will disappear.9. Tower Light Alarm: Turn off the tower light power alarm will appear, if not then climb up the tower and hide the light sensor from light, wait for few minutes while keeping the Tower Light power off. Alarm will appear and do vice versa to clear the alarm.
By Asad Iqbal Jamal