Upload
hoangbao
View
220
Download
0
Embed Size (px)
Citation preview
StepA voice-enabled alarm message is receivedfrom a field radio and processed by theMessage Processing Server(s).
A “received” acknowledgement is sent back tothe field radio, indicating the alarm was receivedand is in process (90 sec push off ack).
Alarm delivery request sent to the digital dialer serverwith request for AlarmNet two-way voice processing.
Alarm message delivery via phone line performed(800plus central station).
Alarm message delivery acknowledgement sent by receiver back to digital dialer (phone line held open).
AlarmNet Two-Way Voice via GSM
606* (two-way voice to follow) sent during the same call.
606* delivery acknowledgement sent by receiverback to digital dialer (phone line held open).
Line held open between digital dialer and central station.Acknowledgement sent from digital dialer to the fieldradio with “two-way voice” command and digital dialerphone number included.
Field radio calls the digital dialer. Digital dialer identifiesincoming call by the caller ID data.
Digital dialer bridges the two voice sessions togetherto create an end-to-end connection for the centralstation operator to the protected premises.
Central Station Commands1 – Speak2 – VOX (talk & listen)3 – Listen7 – Extended session (two minute timeout)9 – Disconnect two-way voice session
Step
VISTA SERIES RESIDENTIAL CONTROL
BATTERY
HANDSET
(EA
RT
H G
ND
(RIN
G)
(TIP
)
GR
Y
BR
N
GR
N
RE
D
INCOMINGPHONE LINE
(RIN
G)
(TIP
)
DIRECTCONNECTCORD
ECP TERMINALS
AVS BASE UNIT
KEYPAD
BLK
GR
N
YE
L
RE
D
MIC
SPEAKERS
DATA
AUDIO
GND
+VDC
YEL
GRN
BLK
RED
AAV
AVST STATION
BRN
GRY
RING
TIP
RING
TIP
(200
FT.
MA
X)
HANDSET
INCOMINGPHONE LINE
SUPPLIED HARNESS
AUDIO CABLE
DATAIN
DATAOUT
PREMISESPHONES
INCOMINGTELCO
RING
TIP
RING
TIP
KEYPAD
7 81 2 3 4 5 6
TRIGGER HEADER
RJ31X
12
3
4 5
67
8
RED BLK GRN YELRED BLK GRN YELRED BLK GRN YEL
PANEL ECP
PHONE
AAV
TO ALLOTHER ECPDEVICES
LED
VOLUME / IDBUTTON
LED
NORMAL MODE
PROGRAM MODE
CALLBACK MODE
PANEL TRIGGERMODE
GND AUX
AUDIO CONNECTOR
IMPORTANT:DO NOT CONNECT ANY OTHERECP DEVICES TO PANEL.USE AVS BASE UNIT ECPTERMINALS FOR OTHER ECP DEVICES.
NOTUSED
DIP SW
DEVICE ADDRESS(ADDRESS 8SHOWN)
TB 1
678
5
1110
9
234
1
GS
MG
PP
SW
EB
MO
DE
2M
OD
E 1
RS
SI
GSMV(OPTIONAL)
VISTA-20P = 11
BASE UNITDEVICE ADDRESS
VISTA-15P = 8
2 3 41
ON
2 3 541
ON
2 3 541
ON
2 3 541
ON
USE EITHER AVS CONNECTIONSBUT NOT BOTH
• Universal control panel compatibility – flexible modes of operationallow ECP alarm reporting by Honeywell control panels, 4204 relaymode for Honeywell controls (that do not support ECP alarm reporting) and zone triggering for use with other control panels
• Control Panel Compatibility – The following VISTA Series families: VISTA-21iP, VISTA-20P (Rev 7 or higher) and VISTA-15P (Rev 6 or higher)
• Either AVS connection can be made(POTS or GSMV) – but
not both
• For detailed installation instructions refer to the
panel installation guide
• Two-way voice GSM model required
• Two-way voice audio cable required
For additional programming please see instructional inserts.
1
2
3
6
7
8
9
10
4
5*606 “Listen-in to follow”. The system is about to activate a two-way audio session.
Ordering InformationGSMVLP – AudioGSMV – AudioGSMX – AudioAVS – Audio Verification SystemAVST – Audio Verification Station
Important Notes
VISTA Series Panel Wiring Diagram
L/VSTA2WYMP/D © 2010 Honeywell International Inc.