Upload
lyngoc
View
251
Download
10
Embed Size (px)
Citation preview
AISINAISIN
Ais
in
January 2012
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
WARNING — User Responsibility
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the “Offer of Sale”.
Offer of Sale
© Copyright 2012, Parker Hannifin Corporation, All Rights Reserved
4.1.II Parker Hannifin CorporationChelsea Products DivisionOlive Branch, MS 38654 USA
Aisin
Parker Hannifin CorporationChelsea Products DivisionOlive Branch, MS 38654 USA
Transmission P.T.O. Driver & Aperatures (Viewed from Rear of Transmission)
L-Left Side R-Right Side B-Bottom Side T-Top Side
For transmission not listed, contact your authorized Chelsea Distributor.
IMPORTANT: See Safety Information in Section 1 of the Chelsea Applications catalog HY25-3000/US.
January 2012
4.1.1
AISIN TRANSMISSION INDEX
Transmission Make and ModelP.T.O.Appl.
Number
NumberForwardSpeeds
Teeth inP.T.O.Driver
A443E AIS-1 4 L58
A445 AIS-1 4 L58
A450-43L IZU-12 4 L58
A450-43LE IZU-12 4 L58
A465 AIS-2 6 L69
MY600 AIS-2 6 L69
Ais
in
Parker Hannifin CorporationChelsea Products DivisionOlive Branch, MS 38654 USA
January 2012
4.1.2
AISIN
Engine %
Caution: Application Approval Required for P.T.O. Output Shaft Speeds Above 2500 R.P.M.
AIS-1
PITCH LINE TO APERTURE FACE:
TRANSMISSION GEAR DATA:
LEFT SIDE ONLY
58 Teeth - SPUR
Inter.Torq.
Dir.Rot. Filler Block
AdapterAssy. Stud Kit
P.T.O. ModelP.T.O. ModelLEFT Side
RevHiStud Kit
AdapterAssy.Filler Block
RevHi
Engine %Dir.Rot.
Inter.Torq.
L.H. 06-Bolt Opening Gear FORWARD of Centerline
1.0880" (27.6352MM)
MO35A4
A445
A443E
ONE SPEED - TWO GEAR - POWERSHIFT (HYDRAULIC)Opp243AGKUP-*5 (1) 85 140 Furnished
270AAKUP-*5 (2) Eng210 55 Furnished
270ABKUP-*5 (3) Eng163 71 Furnished
270ADKUP-*5 (4) Eng139 82 Furnished270AKKUP-*5 (5) Eng104 111 Furnished
270AQKUP-*5 (6) Eng78 148 Furnished
NOTE: When ordering the 270 "A", the hose kit 329246X and metric stud kit 328170-205X is furnished with the P.T.O. The hose kit and metric stud kit are required for completing the 270 Series installation. The 329246X kit supplies hoses for the low pressure lube, high pressure oil, and drain back oil.
NOTE: The torque ratings shown for the 270 Series are based on the maximum allowable torque capacity of the P.T.O. drive gear in the transmission.
NOTE: To mount the 243 Series or 270 Series a revision to the 6 bolt aperture face had to be made so the input gear of the PTO did not interfere with the transmission case. The revised transmission case will have a serial number of 8D3394 or higher.
(1) Input Gear Part No. 5-P-1352(2) Input Gear Part No. 5-P-1353(3) Input Gear Part No. 5-P-1354(4) Input Gear Part No. 5-P-1355(5) Input Gear Part No. 5-P-1356
(6) Input Gear Part No. 5-P-1359
AISIN
Engine %
Caution: Application Approval Required for P.T.O. Output Shaft Speeds Above 2500 R.P.M.
PITCH LINE TO APERTURE FACE:
TRANSMISSION GEAR DATA:
LEFT SIDE ONLY
69 Teeth - SPUR
Inter.Torq.
Dir.Rot. Filler Block
AdapterAssy. Stud Kit
P.T.O. ModelP.T.O. ModelLEFT Side
RevHiStud Kit
AdapterAssy.Filler Block
RevHi
Engine %Dir.Rot.
Inter.Torq.
L.H. 06-Bolt Opening Gear FORWARD of Centerline
1.0880" (27.6352MM)
MO36A6
MY600
A465
AIS-2
ONE SPEED - TWO GEAR - POWERSHIFT (HYDRAULIC)7-A-032 Opp243AGKUP-*5 (1) 65 167 Furnished7-A-032 270AAKUP-*5 (2) Eng167 65 Furnished
7-A-032 270ABKUP-*5 (3) Eng129 85 Furnished
7-A-032 270ADKUP-*5 (4) Eng112 98 Furnished7-A-032 270AKKUP-*5 (5) Eng82 132 Furnished
7-A-032 270AQKUP-*5 (6) Eng62 176 Furnished
NOTE: When ordering the 270 "A", the Hose Kit 329246X and Metric Stud Kit 328170-205X are furnished with the P.T.O. The Hose and Metric Stud Kit are required for completing the 270 Series installation. The 329246X kit supplies the hoses for the low pressure lube, high pressure oil, and drain back oil.
(1) Input Gear Part No. 5-P-1352(2) Input Gear Part No. 5-P-1353(3) Input Gear Part No. 5-P-1354(4) Input Gear Part No. 5-P-1355(5) Input Gear Part No. 5-P-1356
(6) Input Gear Part No. 5-P-1359
Aisin
Parker Hannifin CorporationChelsea Products DivisionOlive Branch, MS 38654 USA
January 2012
AISIN
Engine %
Caution: Application Approval Required for P.T.O. Output Shaft Speeds Above 2500 R.P.M.
PITCH LINE TO APERTURE FACE:
TRANSMISSION GEAR DATA:
LEFT SIDE ONLY
69 Teeth - SPUR
Inter.Torq.
Dir.Rot. Filler Block
AdapterAssy. Stud Kit
P.T.O. ModelP.T.O. ModelLEFT Side
RevHiStud Kit
AdapterAssy.Filler Block
RevHi
Engine %Dir.Rot.
Inter.Torq.
L.H. 06-Bolt Opening Gear FORWARD of Centerline
1.0880" (27.6352MM)
MO36A6
MY600
A465
AIS-2
ONE SPEED - TWO GEAR - POWERSHIFT (HYDRAULIC)7-A-032 Opp243AGKUP-*5 (1) 65 167 Furnished7-A-032 270AAKUP-*5 (2) Eng167 65 Furnished
7-A-032 270ABKUP-*5 (3) Eng129 85 Furnished
7-A-032 270ADKUP-*5 (4) Eng112 98 Furnished7-A-032 270AKKUP-*5 (5) Eng82 132 Furnished
7-A-032 270AQKUP-*5 (6) Eng62 176 Furnished
NOTE: When ordering the 270 "A", the Hose Kit 329246X and Metric Stud Kit 328170-205X are furnished with the P.T.O. The Hose and Metric Stud Kit are required for completing the 270 Series installation. The 329246X kit supplies the hoses for the low pressure lube, high pressure oil, and drain back oil.
(1) Input Gear Part No. 5-P-1352(2) Input Gear Part No. 5-P-1353(3) Input Gear Part No. 5-P-1354(4) Input Gear Part No. 5-P-1355(5) Input Gear Part No. 5-P-1356
(6) Input Gear Part No. 5-P-1359
4.1.3
Ais
in
Parker Hannifin CorporationChelsea Products DivisionOlive Branch, MS 38654 USA
January 2012
AISIN
Engine %
Caution: Application Approval Required for P.T.O. Output Shaft Speeds Above 2500 R.P.M.
IZU-12
PITCH LINE TO APERTURE FACE:
TRANSMISSION GEAR DATA:
LEFT SIDE ONLY
58 Teeth - SPUR
Inter.Torq.
Dir.Rot. Filler Block
AdapterAssy. Stud Kit
P.T.O. ModelP.T.O. ModelLEFT Side
RevHiStud Kit
AdapterAssy.Filler Block
RevHi
Engine %Dir.Rot.
Inter.Torq.
L.H. 06-Bolt Opening Gear FORWARD of Centerline
1.0880" (27.6352MM)
450-43LE
A450-43LE
A450-43L
ONE SPEED - TWO GEAR - POWERSHIFT (HYDRAULIC)Eng270AAKUP-*5 (1) 210 55 Furnished
270ABKUP-*5 (2) Eng163 71 Furnished
270ADKUP-*5 (3) Eng139 82 Furnished
270AKKUP-*5 (4) Eng104 111 Furnished270AQKUP-*5 (5) Eng78 148 Furnished
NOTE: When ordering the 270 "A", the hose kit 329246X and metric stud kit 328170-205X is furnished with the P.T.O. The hose kit and metric stud kit are required for completing the 270 Series installation. The 329246X kit supplies hoses for the low pressure lube, high pressure oil, and drain back oil.
NOTE: The torque ratings shown for the 270 Series are based on the maximum allowable torque capacity of the P.T.O. drive gear in the transmission.
NOTE: The P.T.O.s shown on this application page will fit Isuzu NQR model trucks with serial number X7901741 and later only.
NOTE: The P.T.O.s shown on this application page will fit Isuzu NPR model trucks with wheel bases of 109" or 132" and a serial number of X7006763 and later.
NOTE: The P.T.O.s shown on this application page will also fit the same NPR model trucks with wheel bases of 150" and 176" after August of 1998 and serial number of X7006763 and later.
NOTE: The serial number is the last eight digits found on the VIN plate which is located in the cab behind the driver.
(1) Input Gear Part No. 5-P-1353(2) Input Gear Part No. 5-P-1354(3) Input Gear Part No. 5-P-1355(4) Input Gear Part No. 5-P-1356(5) Input Gear Part No. 5-P-1359
4.1.4