AIRJET Jet Fans Axial-Flow Fans Axial-Roof Fans Smoke Exhaust … · 2015. 5. 16. · HV-AIRJET AJU/AJR F300 jet-fan series 9 Jet-fan F300 (300°C/120min.) or normal. AIRJET nominal

AIRJET Jet Fans Axial-Flow Fans Axial-Roof Fans Smoke Exhaust Axial-Flow Fans Smoke Exhaust Axial Roof Fans

H UNGARO-VENTILÁTOR LTD.

2 HV-VMA middle pressure axial-flow fan series

Middle pressure axial-flow fan with aluminum impeller

and direct drive.

VMA nominal sizes: 560-1000mm.

For extraction or supply of pure air with max.

temperature of 50°C or 80°C. Also for horizontal and

vertical mounting positions!

Description:

Casing of sheet-steel with rolled flanges on both sides and

with bolted motor support. Surfaces protected through hot

dip galvanizing or powder-painting.

Impeller with airfoil aluminum cast alloy blades and aluminum cast alloy hub and with a taperlock hub connection on

motor shaft. Pitch angle is infinitely adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,

balance quality class G6.3.

Three-phase alternating current motor /IEC – standard motor in B3 mounting form, protection type IP 55/ insulation

class ISO-H. Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the

externally located terminal box.

Performance curves are according to EN24163 and EN ISO 5801 tested in a tube testing station.

HUNGARO-VENTILÁTOR LTD.

Táncsics Mihály utca 18. H-9483 Sopronkövesd Hungary

Telephone: +36-99/536-072 Fax: +36-99/536-073

Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-yentilator hu

HV-VMB middle pressure axial-flow fan series 3

Middle pressure axial-flow fan with aluminum

impeller and direct drive.

VMA nominal sizes: 560-1000mm.


temperature of 50°C or 80°C. Also for horizontal

and vertical mounting positions!

Description:

Casing of sheet-steel with rolled flanges on both

sides and with bolted motor support. Surfaces protected through hot dip galvanizing or powder-painting.

Impeller with airfoil aluminum cast alloy blades and aluminum cast alloy hub and with a taperlock hub connection on

motor shaft. Pitch angle is infinitely adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,

balance quality class G6.3.

Three-phase alternating current motor /IEC – standard motor in B3 mounting form, protection type IP 55/ insulation

class ISO-H. Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the

externally located terminal box.

Performance curves are according to EN24163 and EN ISO 5801 tested in a tube testing station.



Telephone: +36-99/536-072 Fax: +36-99/536-073


4 HV-VMC middle pressure axial-flow fan series

Middle pressure axial-flow fan with plastic blade

impeller and direct drive.

VMC nominal sizes: 315-1250 mm


temperature of 50°C o r80°C. Also for horizontal

and vertical mounting positions.

Description:


sides and with bolted motor support. Surfaces

protected through hot dip galvanizing or powder painting.

Impeller with airfoil plastic (PP or PAG) blades and aluminum cast alloy hub and with an easy-to-assembly hub-shaft

connection. Pitch angle is in steps adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1,

balance quality class G 6.3.

Three-phase alternating current motor / IEC - standard motor in B3 mounting, protection type IP 55 / insulation

class F or H. Motor power selected for a cold-start at pure air with a density of ρ=1,2kg/m3. Electrical wiring on

the externally located terminal box.

Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing station.



Telephone: +36-99/536-072 Fax: +36-99/536-073


HV-ZVMC middle pressure twin axial-flow fan series 5

Middle pressure twin axial-flow fan with plastic

blade impeller and direct drive.

ZVMC nominal sizes: 315-1250mm


temperature of 50°C or 80 °C. Also for horizontal

and vertical mounting positions!

Description:


sides and with bolted motor support. Surfaces protected through hot dip galvanizing or powder-painting.

Impeller with airfoil plastic (PPor PAG) blades and aluminum cast alloy hub and with an easy-to-assembly hub-shaft

connection. Pitch angle is in steps adjustable at rest. Impeller is dynamically balanced according to EN ISO 1940-1, balance

quality class G6.3.

Three-phase alternating current motor / IEC - standard motor in B3 mounting, protection type IP 55 / insulation class F

or H. Motor power selected for a cold start at pure air with a density of ρ = 1,2kg/m3. Electrical wiring on the externally

located terminal box.

Performance curves are according to EN 24163and EN ISO 5801 tested in a tube testing station.



Telephone: +36-99/536-072 Fax: +36-99/536-073


6 HV-VM..D middle pressure axial-flow roof fan

Middle pressure axial-flow roof-fan with aluminum/plastic blade impeller and direct drive. Also for supply and exhaust. VMAD Roof-fan with an axial-flow fan type VMA - aluminum impeller VMBD Roof-fan with an axial-flow fan type VMB - aluminum impeller VMCD Roof-fan with an axial-flow fan type VMC - plastic blades

For extraction or supply of pure air with max. temperature of 50°C or

80°C. For roof installation in vertical mounting position!

Description:

A roof hood mounted on an axial-flow fan. In case of exhaust, a use of an inlet

cone - as

optional accessory - is necessary.

Three-phase alternating current motor I IEC - standard motor in. B3

mounting, protection type IP 55 insulation class F or H. Motor power selected for a cold start at pure air with a density of ρ =

1.2 kg/m3. Electrical wiring on the externally located terminal box.

Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing

station.



Telephone: +36-99/536-072 Fax: +36-99/536-073


HV-VM..DT middle pressure axial-flow roof fan 7

Middle pressure axial-flow roof fan with aluminum/plastic blade impeller and direct drive. Also for supply and exhaust.

A1so for supply and exhaust.

VMADT Roof fan with an axial-flow fan type VMA - aluminum impeller

VMBDT Roof fan with an axial-flow fan type VMB - aluminum impeller

VMCDT Roof fan with an axial-flow fan type VMC - plastic blades

For extraction or supply of pure air with max. temperature of 5O°C or 80°C.

For roof installation in vertical mounting position!

Description:

A roof hood mounted on an axial-flow fan. In case of exhaust, a use of an inlet cone - as

optional accessory - is necessary.

Three-phase alternating current motor I IEC - standard motor in. B3 mounting, protection type IP 55 insulation class F or

H. Motor power selected for a cold start at pure air with a density of ρ = 1.2 kg/m3. Electrical wiring on the externally located

terminal box.

Performance curves are according to EN 24163 and EN ISO 5801 tested in a tube testing

station.



Telephone: +36-99/536-072 Fax: +36-99/536-073

Mobil:+36-30/689-5939, +36-30/396-5162 E-mail: info@hungaro-ventilator hu

8 HV-BVHA F400/F300 smoke exhaust axial-flow fan series

High pressure smoke exhaust axial flow fan F400 (400°C/120min.) / F300 (300°C/120min.)

BVHA nominal sizes: 335-1400mm

Tested and certified according to EN 12101-3, class F400 and F300. Also for horizontal and vertical installation.

Description: Casing of sheet-steel with rolled flanges on both sides and with welded outlet guide vanes as motor support. Surfaces protected through hot dip galvanizing or powder painting.

Impeller with steel blades welded on a steel hub that directly mounted on motor shaft. Pitch angle is fixed. Impeller is dynamically

balanced according to EN ISO 1940-1, balance quality class G 6.3.

Three-phase alternating current motor / special F400/F300 motor in B3 or B14 mounting, protection type IP55 / insulation class H.

Motor power selected for a cold start at pure air with a density of ρ =1,2kg/m3. Electrical wiring on the externally located terminal

box.


Special fans: •Tunnel fans on both sides silencers, tested and certified according to EN 12101-3, class F400 or F300.



Telephone: +36-99/536-072 Fax: +36-99/536-073


HV-AIRJET AJU/AJR F300 jet-fan series 9

Jet-fan F300 (300°C/120min.) or normal.

AIRJET nominal sizes : 280…400mm Tested and certified according to EN 12101-3, class

F300.

Description:

In unidirectional (AJU) or reversible (AJR) execution.

Insists of an in the middle situated axial-flow fan and both

sides silencers in a high-sparing oval design. The interior

set of fan-motor may be easily pulled out through the

silencer. Direction of the outlet air may be regulated by

using the outlet-louvres.

Impeller with airfoil aluminum cast alloy

blades and aluminum cast alloy hub and

with a taperlock hub connection on motor

shaft. Pitch angle is infinitely adjustable at

rest. Impeller is dynamically balanced

according to EN ISO 1940-1, balance

quality class G6.3.

Three-phase alternating current , special

F300 or normal motor in B3 mounting

form, protection type IP 55 / insulation

class H or F. Motor power selected for a

cold start at pure air with a density of ρ=

1,2kg/m3.

Optional electrical wiring on the externally located terminal box.

AJRJ/AJU jet-fans are tested and certified according to EN 12101-3:2002/ EN 12101-3:2002/AC:200S in classes of

F200(120) and F300(120) temperature (time).




Telephone: +36-99/536-072 Fax: +36-99/536-073


•

10 BVHA F400/F300 + louvre-hood as smoke exhaust roof-fan

High pressure smoke exhaust axial roof-fan F400 (400°C/120min.) / F300 (300°C/120min.)

BVHA F300/F400 + louvre hood nominal sizes: 335-1400mm

Tested and certified according to EN 12101-3, class F400 (400°C/120min.) and F300 (300°C/120min.)

Description:

A pressure activated louvre-hood mounted on a BVHA smoke exhaust

axial-flow fan in vertical mounting position as roof fan for external usage.

Smoke outlet direction is above 45°.

Casing of sheet-steel with rolled flanges on both sides and with welded outlet

guide vanes as motor support. Surfaces protected through hot dip galvanizing

or powder-painting.

Impeller with steel blades welded on steel hub, that directly mounted on

motor shaft. Pitch angle is fixed. Impeller is dynamically balanced according

to EN ISO 1940-1, balance quality c1ass G6.3.

Three-phase alternating current, special F400/F300 motor in mounting form

B3 or B14. Protection type IP55 / insulation class H. Motor power selected

for a cold start at pure air with a density of ρ = 1,2 kg/m3. Electrical wiring

on the externally located terminal box.

Performance curves are according to EN 24163 and EN ISO 5801, tested in a

tube testing station.



Telephone: +36-99/536-072 Fax: +36-99/536-073


Documents

AIRJET Jet Fans Axial-Flow Fans Axial-Roof Fans Smoke Exhaust … · 2015. 5. 16. · HV-AIRJET AJU/AJR F300 jet-fan series 9 Jet-fan F300 (300°C/120min.) or normal. AIRJET nominal