CR159-RG58DBGEFU116117000A01982

AIR CONDITIONER

REMOTE CONTROLLER ILLUSTRATION

Thank you very much for purchasing our air conditioner.Please read this owner's manual carefully before usingyour air conditioner.

The design and specifications are subject to change without prior noticefor product improvement. Consult with the sales agency or manufacturerfor details.

CONTENTS Model

Rated Voltage

8m

3.0V(Dry batteries R03/LR03 2)×

RG58D/BGEFEU1

Remote Controller Specifications

Environment

Signal ReceivingRange

NOTE:

Buttons design is based on typical model and might be slightly different from theactual one you purchased the actual shape shall prevail.All the functions described are accomplished by the unit. If the unit has no thisfeature, there is no corresponding operation happened when press the relativebutton on the remote controller.When there are wide differences between Remote controller Illustration andUSER'S MANUAL on function description, the description of USER'S MANUALshall prevail.

，

,,,, ,,

,,,, ,,

2

3

6

7

7

7

8

9

13Handling the remote controller ......................................................

Remote controller Specifications...................................................

Operation buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons .................................................................

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Timer operation...............................................................................AUTO

ECO SET TEMP. ON OFF

AUTO

COOL DRY HEAT FAN

SHORTCUT

23 F~140 FO O

1 1

2 2

4 4

5 5

3 3

9 9

10 10

8 86 6

7 7

1

2

3

4

ON/OFF Button( )This button turns the air conditioner ONand OFF.

Used to select the fan speed in four steps:HIGH MED LOW AUTO

Used to select the fan speed in four steps:AUTO LOW MED HIGH

FAN Button( )

FAN Button( )

You can not switch the fan speed in AUTOor DRY mode.

Press the Fan button( ) , MODE button,ON/OFF or ECO button will cancel the Silentfunction.

Operation of buttons

SET Button

UP Button( )

Push this button to decrease the settemperature or Timer setting hours.

DOWN Button( )

5

6

Press this button to increase the settemperature or Timer setting hours.

Operation of buttons

NOTE：

NOTE：

NOTE：

AUTO AUTO

ECO SET TEMP. ECO SET TEMP.ON ONOFF OFF

AUTO AUTO

COOL COOLDRY DRYHE AT HEATFAN FAN

SET SET

MODE MODE

When the air conditioner operates underheating mode with the set temperature of62 F, pressing button continously fortwo times will activate 46 Degree heating.The indoor unit display shows FP .

O

,,,,

Hold down this button for at least 2 secondsto activate/cancel mode.Silent Due to lowfrequency operation of compressor, it mayresult in insufficient cooling and heatingcapacity.

Hold down this button for at least 2 secondsto activate/cancel mode.Turbo Turbo functionenables the unit to reach the preset temperatureat cooling or heating operation in the shortesttime (if the indoor unit does not support thisfunction, there is no corresponding operationhappened when pressing this button.)

Used to stop or start horizontal louver move-ment . Hold down this button for 2 secondsto start/stop vertical louver movement.

Swing Button( )

Used to initiate the following functions in thesequence below, in conjuction with the& buttons.

Timer off Self clean

Follow meSleepFresh

Timer on

( Indicate optional functions)Press the SET button to select the desiredfunction, the selected symbol will flash onthe display area, then press the orbutton to confirm.

SLEEP function( )

FRESH function( )(optional)

SELF CLEAN function( )(optional)

It can maintain the most comfortable temper-ature and save energy. This function isavailable on COOL, HEAT or AUTO mode only .

When the FRESH function is initiated, theIonizer/Plasma Dust Collector(depending onmodels) is energized and will help toremove pollen and impurities from the air.

For the detail, see sleep operation inUSER S MANUAL.

,

,,,,

,,,,

Under SELF CLEAN mode, the airconditioner will automatically clean anddry the Evaporator and keep it as freshfor the next operation.

SHORTCUT

SHORTCUT

8

10

Operation of buttons Indicators on LCD

Fan speed indication

Mode displayInformation are displayed whenthe remote controller is poweredup.

Displayed when data transmitted.

Displayed when remote controller is ON.

Indicated LOCK feature is activated

Battery display(low battery detection)

Displayed in ECO mode operation

Low speed

Medium speed

High speed

Auto fan speed

Note:All indicators shown in the figure are for the purposeof clear presentation. But during the actual operationonly the relative functional signs are shown on thedisplay window.

Displayed when TIMER ON time is set.

Displayed in Sleep Mode operation.

Displayed in Self clean operation.

Displayed when Silent feature is activated

Indicated that the air conditioner isoperating in Follow me mode

Displayed in Fresh operation.

Displayed when TIMER OFF time is set.

Show set temperature or roomtemperature, or time under TIMERsetting.

1

2

4

5

3

9

10

86

7

AUTO

ECO SET TEMP. ON OFF

AUTO

COOL DRY HEAT FAN

SET

MODE

Press this button to modify the air conditionermode in a sequence of following:

MODE Button

AUTO COOL DRY HEAT FAN

NOTE：Please do not select HEAT mode if themachine you purchased is cooling only type.Heat mode is not supported by the cooling onlyappliance.

9

7

AUTO

AUTO

ECO SET TEMP. ON

ON

OFF

OFF

COOL

COOL

AUTO

AUTO

DRY

DRY

HEAT

HEAT

FAN

FAN

SHORTCUT

SHORTCUT ButtonUsed to restore the current settings orresume previous settings.On the first time connecting to the power,if push the SHORTCUT button, the unitwill operate on AUTO mode, 80 F, and fanspeed is Auto.Push this button when remote controller ison, the system will automatically revertback to the previous settings includingoperating mode, setting temperature, fanspeed level and sleep feature(if activated).If pushing more than 2 seconds, the systemwill automatically restore the currentoperation settings including operating mode,setting temperature, fan speed level andsleep feature(if activated ).

O

FOLLOW ME function( )(optional)When the Follow Me function is activated,the remote display is actual temperatureat its location. The remote control will sendthis signal to the air conditioner every 3minutes interval until press the FOLLOWME button again.

LOCK FunctionPress SHORT CUT and LED buttonssimultaneously to lock or unlock the keyboard.

LED Button( )Press this button to turn on/off the indoorscreen display.

How to use the buttons

Cooling /Heating/Fan operation

MODE

UP/DOWN

FAN

ON/OFF

Ensure the unit is plugged in and power isavailable.1. Press the button to select COOL,

HEAT(cooling & heating models only) orFAN mode.

2. Press the buttons to set thedesired temperature.

3. Press the button to select the fan speedin four steps- Auto, Low, Med,or High.

4. Press the button to start the airconditioner.

The temperature canbe set within a range of 62 F~86 F in 1 Fincrements.

O O O

In the FAN mode, the setting temperature is notdisplayed in the remote controller and you are notable to control the room temperature either. In thiscase, only step 1, 3 and 4 may be performed.

NOTE

Auto operation

MODEUP/DOWN

ON/OFF

Ensure the unit is plugged in and power isavailable. The OPERATION indicator on thedisplay panel of the indoor unit starts flashing.1. Press the button to select Auto.2. Press the button to set the

desired temperature. The temperature canbe set within a range of

3. Press the button to start the airconditioner.

62 F~86 F in 1 Fincrements.

O O O

1. In the Auto mode, the air conditioner can logicallychoose the mode of Cooling, Fan, and Heatingby sensing the difference between the actualambient room temperature and the settingtemperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed.It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , thedesired mode can be selected manually.

NOTE

Dehumidifying operation

MODEUP/DOWN

ON/OFF

Ensure the unit is plugged in and power isavailable. The OPERATION indicator on thedisplay panel of the indoor unit starts flashing.1. Press the button to select DRY mode.2. Press the buttons to set the

desired temperature.

3. Press the button to start the airconditioner.

The temperaturecan be set within a range of 62 F~86 F in1 F increments.

O O

O

In the Dehumidifying mode, you can not switch thefan speed. It has already been automatically controlled.

NOTE

How to use the buttons

4

3 3

3

2 2

1 1

AUTO

SETSET

MODEMODE

DRYCOOL

SET TEMP.SET TEMP.

SHORTCUT SHORT

CUT

Timer operationPress the SET button can set the auto-on/offtime of the unit.

1. Press the SET button, the Timer on indicator " "displays and flashes, the last Auto-on setting timeand the signal "h" will be shown on the LCD displayarea. Now it is ready to reset the Auto-on time toSTART the operation.

2. Press the or button to set desired Auto-ontime. Each time you press the button, the timeincreases/decreases by half an hour between 0and 10 hours and by one hour between 10 and24 hours.

3. Once the desired time establishes ,there will bethree seconds delay before the remote controllertransmits the signal to the air conditioner. Then,the signal "h" will disappear , the Timer on indicatorwill remain on and the set temperature willre-appear on the LCD display window.

1. Press the SET button until the Timer on indicator" " displays and flashes, the last Auto-offsetting time and the signal "h" will be shown on theLCD display area. Now it is ready to reset theAuto-off time to STOP the operation.

2. Press the or button to set desired Auto-offtime. Each time you press the button, the timeincreases/decreases by half an hour between 0and 10 hours and by one hour between 10 and24 hours.

3. Once the desired time establishes ,there will bethree seconds delay before the remote controllertransmits the signal to the air conditioner. Then,the signal "h" will disappear, Timer off indicatorwill remain on and the set temperature willre-appear on the LCD display window.

To set the Auto-on time.

To set the Auto-off time.

When you select the timer operation, the remote controller automatically transmits thetimer signal to the indoor unit for the specified time. Therefore, keep the remotecontroller in a location where it can transmit the signal to the indoor unit properly.The effective operation time set by the remote controller for the timer functionis limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,21, 22, 23 and 24.

CAUTION!

Example of timer setting

Start

Off

6 hours later

(Auto-on Operation)The TIMER ON feature is useful when you wantthe unit to turn on automatically before you returnhome. The air conditioner will automatically startoperating at the set time.

To start the air conditioner in 6 hours.1. Press the SET button to select TIMER ON, the

last setting of starting operation time and thesignal

2. Press the or button to display"6.0h on the TIMER ON display of the remotecontroller.

3.

"h" will show on the display area.

"

Wait for three seconds and the digital displayarea will show the temperature again. The" " indicator remains on and thisfunction is activated.

TIMER ON

Example:

ON

OFF

ON OFF

2

1SET

MODE

COOL

SET TEMP.

ON

ON

SHORTCUT

Stop

On

Set 10 hours later

(Auto-off Operation)The TIMER OFF feature is useful when you want theunit to turn off automatically after you go to bed. Theair conditioner will stop automatically at the set time.

TIMER OFF

Example:

OnStop

2 hours laterafter setting

Set

To stop the air conditioner 2 hours after setting andstart it again 10 hours after setting.1. Press the SET button to select TIMER OFF.2. Press the or button to display

2.0h on the TIMER OFF display.3.4. Press the or button to display 10h

on the TIMER ON display .5.

Press the SET button to select TIMER ON.

Wait for three seconds and the digital display areawill show the temperature again. The "& " indicators remain on and this functionis activated.

TIMER OFF TIMER ON(On Stop Start operation)This feature is useful when you want to stop the airconditioner after you go to bed, and start it again inthe morning when you wake up or when you returnhome.

→

→ →

Example:

COMBINED TIMER(S both ON and OFF )etting timers simultaneously

Start

10 hours laterafter setting

Example:

TIMER ON TIMER OFF(Off Start Stop operation)This feature is useful when you want to startthe air conditioner before you wake up andstop it after you leave the house.

→→ →

To start the air conditioner 2 hours after setting,and stop it 5 hours after setting.1. Press the SET button to select TIMER ON.2. Press the or button to display

2.0h on the TIMER ON display.3. Press the SET button to select TIMER OFF.4. Press the or button to display

5.0h on the TIMER OFF display .5. Wait for three seconds and the digital display area

will show the temperature again. The "& " indicators remain on and

this function is activated.

Off Stop

Start

2 hours laterafter setting

5 hours laterafter setting

Set

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

To sop the air conditioner in 10 hours.1. Press the SET button to select TIMER OFF, the

last setting of stopping operation time and thesignal

2. Press the or button to display"10h on the TIMER OFF display of the remotecontroller.

3.

"h" will show on the display area.

"

Wait for three seconds and the digital displayarea will show the temperature again. The" " indicator remains on and thisfunction is activated.

8m

Use the remote controller within a distance of 8meters from the appliance, pointing it towards thereceiver. Reception is confirmed by a beep.

The remote controller can be attached to a wall orpillar by using a remote controller holder(not supplied,purchased separately).Before installing the remote controller, check that theair conditioner receives the signals properly.Install the remote controller with two screws.For installing or removing the remote controller, moveit up or down in the holder.

The following cases signify exhausted batteries.Replace old batteries with new ones.

Receiving beep is not emitted when a signalis transmitted.Indicator fades away.

Location of the remote controller.

Using the remote controller holder(optional)

The remote controller is powed by two drybatteries (R03/LR03X2) housed in the back rearpart and protected by a cover.(1) Remove the cover in the rear part of the

remote controller.(2) Remove the old batteries and insert the new

batteries,placing the(+) and (-) ends correctly.(3) Install the cover back on.

When the batteries are removed, theremote controller erases all programming. Afterinserting new batteries, the remote controllermust be reprogrammed.

NOTE:

Replacing batteries

CAUTIONSThe air conditioner will not operate if curtains,doors or other materials block the signals fromthe remote controller to the indoor unit.Prevent any liquid from falling into the remotecontroller. Do not expose the remote controllerto direct sunlight or heat.If the infrared signal receiver on the indoor unitis exposed to direct sunlight, the air conditionermay not function properly. Use curtains toprevent the sunlight from falling on the receiver.If other electrical appliances react to the remotecontroller, either move these appliances orconsult your local dealer.Do not drop the remote controller. Handle with care.Do not place heavy objects on the remote controller,or step on it.

CAUTIONSDo not mix old and new batteries or batteriesof different types.Do not leave the batteries in the remotecontroller if they are not going to be used for2 or 3 months.Do not dispose batteries as unsortedmunicipal waste. Collection of such wasteseparately for special treatment is necessary.

Handling the remote controller

(1)

(2)