Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
www.enverid.com
Air Purifier Installation Guide
enVerid Technical Documentat ion
SEPTEMBER 2020
V1.0
enverid.com
1. enVerid Air Purifier Installation View
BELOW THE CEILING (UNCONCEALED INSTALLATION) SIDE VIEW
AIR PURIFIER TOP VIEW
IN THE CEILING (CONCEALED INSTALLATION) SIDE VIEW
Floor Slab
Ceiling
Floor Slab
Air PurifierReturn Grille Supply Grille
3/8” Threaded Rod
Air PurifierDuctworkReturn Grille Supply Diffuser
Pre Filter
High Efficiency Filter
3/8” Threaded Rod
Blower UVC LampsSilencer
Floor Slab
Ceiling
Ceiling
Air PurifierDuctworkReturn Grille
Duct Clamp
Supply Diffuser
FilterAccessDoor
Control Box
Pre Filter
High Efficiency Filter
Air Muffler Box
3/8” Threaded Rod
Blower UVC LampsSilencer
3/8" Threaded Rod
Floor Slab
Ceiling
Floor Slab
Air PurifierReturn Grille Supply Grille
3/8” Threaded Rod
Air PurifierDuctworkReturn Grille Supply Diffuser
Pre Filter
High Efficiency Filter
3/8” Threaded Rod
Blower UVC LampsSilencer
enVerid Installation Guide
enverid.com
enVerid Installation Guide
2. enVerid Air Purifier Installation BOM List (not included in packaging)
NO.
1
5
11
3
9
7
13
2
6
12
4
10
8
14
IMAGENAME
Isolation Hangers
Suspension Rubber Washer
Duct Collar
Expansion Bolt
Spiral Duct
Return Air Box
485 Communication Wires
Hanging Bar
Return Air Grille
Power Line
Washer
Duct Clamp
Duct Silencer
Mccb Circuit Breaker
QTY.
4
4
3
4
2
1
Multiple
Multiple
1
Multiple
4
4
2
1
REMARK
TD-65lbs only for Purifier
3/8” Rubber Washer
8” Flexible collar
3/8” Expansion bolt NOTE: Beam clamps may be used in case where
air purifier is supported by building framing.
8” x 60” NOTE: For use in hard duct applications.
20”x20”x14” – 1” liner for sound attenuation or confirm on site
18 gauge, 2 wire, stranded and shielded wire
3/8” Threaded Rod
20”x20” minimum or to be confirmed by PM
See power requirements and local code
3/8” Fender Washer
8” Duct Clamp
8” x 40” NOTE: For use with flexible duct for sound attenuation.
MOCP 15 Amp – Do not exceed code requirements and guidelines for number of units per circuit
enverid.com
enVerid Installation Guide
3. enVerid Air Purifier Installation Method
NO.
1
5
3
7
2
6
4
8
IMAGENAME
Equipment Body
Screws
Operation and Maintenance Guide
Pre-Filter
Controller
Flange
Angle Bracket
High Efficiency Filter
QTY.
1
Multiple
1
1
1
3
4
1
REMARK
Individually packed
Included in accessories bag
Included in data packet
Included in equipment body
Individually packed
Included in equipment body NOTE: 2-Supply
1-Return
Included in accessories bag
Included in equipment body
STEP 1 Open package and check parts/documents. Assemble angle bracket (item 4) to unit (item 1) as below.
STEP 2 Install expansion bolts and threaded rod into slab. Use 3/8” expansion bolt drill depth of minimum 2”, as below.
NOTE: Minimum recommended installation height 7.5ft above the floor. Maximum recommended installation height 16ft above the floor.
Floor Slab
Air PurifierReturn Grille Arc GrilleAir Muffler Box
Expansion Bolt
2” Min. Into the SlabNuts
3/8” Threaded Rod
enverid.com
enVerid Installation Guide
STEP 3 Use four threaded rods to hang the unit, fixed with screws, and install appropriate vibration isolation devices.
The equipment location must allow access to the filter for replacement and the control board for service (A).
STEP 5 Install ductwork per local code and SMACNA guidelines. 40” minimum of hard duct silencers is suggested for flexible duct installations and 60” minimum for hard duct installations.
Both supply and return should be insulated or lined to dampen system sound.
Floor Slab
Filters Silencing Section
3/8” Threaded RodIsolation Hangers
STEP 4 Install the Air Purifier box to the slab with 3/8” standard threaded rod at the corresponding position.
NOTE: UVC lamps can be removed prior to installing the Air Purifier box if the UVC lamps will not be used.
A
enverid.com
enVerid Installation Guide
STEP 6 Power supply wiring: cabling should be contained within conduit, and connected to PCB board as shown.
STEP 7 Control panel wiring: The position of the control switch panel shall be decided and confirmed with client and/or main contractor.
Cabling should be contained within conduit and controller connected to panel board with RVSP line as shown.
STEP 8 Installation of filter: Please note that the arrow on the filter is the direction of air flow as below. Filters should be installed after cleaning work has been completed on-site.
The reset button on the Controller should be pressed once the filters are installed to reset the maintenance schedule for the filters. Once reset, the Filter Life counter in the Notification Center under the speed display will say 365 or 182 days to indicate a 12 or 6 month filter life. The high efficiency filter should be replaced every 6 months when the UVC lamp is used and every 12 months if the UVC lamp is not used by removing the UVC lamps from the unit. If the filter life shows 182 days and you are operating the system without the UVC lamp, then one maintenance schedule can be skipped each cycle. The counter is hard-coded to either 365 or 182 days.
NOTE: Filters should only be installed once the building is completely clean of construction debris and dust.
www.enverid.com
enVerid Installation Guide
enverid.com · 1.617.795.4000 · [email protected] Energy Savings. Air Quality.
©2020 enVerid Systems, Inc. All rights reserved. Third-party trademarks mentioned are the property of their respective owners. | 2020-09-02_AP_Install_v1
enVerid helps buildings achieve ESG (Environmental, Social, and Governance), healthy building, and cost saving goals by improving indoor air quality while saving money and reducing energy consumption and carbon emissions. For new HVAC systems, enVerid’s award-winning HVAC Load Reduction (HLR) Modules enable immediate capital cost savings. HLR Modules also deliver up to 30% energy savings and superior indoor air quality in new and existing buildings. enVerid’s air filtration products remove particulate and microorganism contamination from indoor air without the significant cost of upgrading mechanical systems and increasing mechanical ventilation rates. enVerid’s products are deployed in commercial, academic and government buildings globally. enVerid’s HLR Modules are ASHRAE Standard 62.1, LEED, and WELL compliant and eligible for utility rebates. For more information visit https://enverid.com.
4. enVerid Air Purifier Wiring Diagram