1901 North Fort Myer Drive Arlington, Virginia 22209

, The user of this Standard ( AGMA 420.04) may find these other AGMA Standards of value as reference data:

Number Title

\.' AGMA 110.03 AGMA 11 2.04 AGMA 201.02

AGMA 209.03 AGMA 2 10.02

\A AGMA 21 1.02 AGMA 2 12.02

t' AGMA 215.01

AGMA 216.01 \:- AGMA 220.02 !- AGMA 221.02

AGMA 222.02 AGMA 223.0 1

\ AGMA 225.01

AGMA 240.01 .'. AGMA 250.03 i-! AGMA 25 1 .o,~L LI AGMA 260.02

AGMA 297 .O1 \: AGMA 390.03

Gear-Tooth Wear and Failure (USAS B6.12-1964) . . . . . . . . . . . . . . . . . . . . . . . . . . Terms, Definitions, Symbols, and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tooth proportions for Coarse-Pitch Involute Spur Gears

(ANSIB6.1-1968) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System fox Spiral Bevel Gears . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface Durability (Pitting) of Spur Gear Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface Durability (Pitting) of Helical and Herringbone Gear Teeth . . . . . . . . . . . . . Surface Durability (Pitting) Formulas for Straight Bevel and

Zero1 Bevel Gear Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information Sheet for Surface Durability (Pitting) of Spur,

Helical, Herringbone and Bevel Gear Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface Durability (Pitting) Formulas for Spiral Bevel Gear Teeth . . . . . . . . . . . . . . Rating the Strength of Spur Gear Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rating the Strength of Helical and Herringbone Gear Teeth . . . . . . . . . . . . . . . . . . . Rating the Strength of Straight Bevel and Zero1 Bevel Gear Teeth . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . -Rating the Strength of Spiral Bevel Gear Teeth Information Sheet for Strength of Spur, Helical, Herringbone

andBevelGearTeeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information Sheet - Geometry Factors for Determining the

Strength of Spur, Helical, Herringbone and Bevel Gear Teeth ............. Gear Materials Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . Specification - Lubrication of Industrial Enclosed Gear Drives . . . . . . . . . . . . . . . . . . . . . . . . . . Specification - Lubrication of Industrial Gearing

Design of Components - ~ncldsed Gear Drives - Bearings, ~ o l t i n ~ Keysandshafting ..............................................

Sound for Enclosed Helical, Herringtone and Spiral Bevel Gear Drives ........... AGMA Gear Handbook - Volume I - Gear Classification, Materials

. . . . . . . . . . . . . . . . . . . . . . . and Measuring Methods for Unassembled Gears

A more complete list of AGMA Standards published by the American Gear Manufacturers Association is available upon request.

PUBLISHED BY AMERICAN GEAR MANUFACTURERS ASSOCIATION

1901 NORTH FORT MYER DRIVE, ARLINGTON, VIRGINIA 22209

PRICE $18.00