HEADSIGHT.COM | 574.546.5022

Conversion Manual09040404a

AGCO 3300

i

Installation

About Headsight

Headsight Contact InfoHeadsight, Inc. 4845 3B Road Bremen, IN 46506 Phone: 574-546-5022 Fax: 574-546-5760 Email: info@headsight.com Web: www.headsight.com

Technical AssistancePhone: 574-220-5511

About this Manual

How to use this manualThe instructions in this manual are in the order that they should be completed for new installations. Complete all applicable instructions in each section before proceeding. Note that some sections are labeled to indicate they only apply to certain machines or applications. An index is available in the front of the manual to help find technical information for previously installed systems.

This icon designates information of which you should take note.

This icon indicates a special tool needed for a given task.

This icon designates an important instruction.

DisclaimersHeadsight®, Horizon®, Pinpoint®, Insight®, Foresight®, Feathersight® Truesense™ and Truesight® are trademarks of Headsight, Inc. All other trademarks are property of their respective owners.

SuggestionsIf you have any suggestions to improve this manual please call 574-546-5022 or email info@headsight.com.

Headsight’s products are protected by one or more of the following US Patents 6202395, 6833299, 7310931, 7647753 and other patents pending.

Copyright Headsight, Inc. 2017

ii

Installation

Table of ContentsAbout Headsight ��������������������������������������������������������������������������������������������� iAbout this Manual ������������������������������������������������������������������������������������������� iInstallation �������������������������������������������������������������������������������������������������� 1

Identify the components �������������������������������������������������������������������������������� 2Sensor Installation (Optional)�������������������������������������������������������������������������� 4Insight Box Mounting ������������������������������������������������������������������������������������ 7Header Adapter Installation ���������������������������������������������������������������������������� 7Power Adapter Installation: Late Models ������������������������������������������������������������� 7Power Adapter Installation: Early Models ������������������������������������������������������������ 8

Sensor Adjustment ����������������������������������������������������������������������������������������� 9Changing Swing ������������������������������������������������������������������������������������������� 9Increasing or Decreasing Voltage ���������������������������������������������������������������������� 9Sensor Extensions ���������������������������������������������������������������������������������������10

Parts ���������������������������������������������������������������������������������������������������������11KIT - HT2291 ���������������������������������������������������������������������������������������������11Insight Kit �������������������������������������������������������������������������������������������������12Corn Sensor HT2000 ������������������������������������������������������������������������������������13

STATEMENT OF LIMITED WARRANTY �����������������������������������������������������������������15

1

Installation

Installation

Before working under header always:

1. Perform all combine and header manufacturer safety precautions for servicing header.

2. Insert stop to prevent movement of header.

3. Turn off combine and remove key from ignition.

4. Set combine parking brake.

5. Disconnect all drive shafts from the header.

2

Installation

Identify the components

1. Insight Interface• Insight• Mounting kit- BC-BOX

2. Insight Adapter harness • QC1-AG12-XX Main Harness

3. Power adapter, late model• PFI-AG3300-P

• MF 95xx & up• Challenger 5x0C & up,• Gleaner S9x & up

4. Power adapter, early model• PFI-AG13-P

• MF 9x95 & prior• Challenger 6x0B & prior• Gleaner S8x & prior

3

Installation

5. OPTIONAL: HT2291 Sensor kit• adds 3rd or 5th sensor

4

Installation

Sensor Installation (Optional)

1. Install the sensor into the Mounting Bracket.• Sensor• HT2290 mount• B2290 bolt kit

2. Remove the OEM skid shoe assembly and reinstall the front 2 bolts.

3. Mount the sensor assembly into the Snout.• B2290 Bolt Kit

4. Remove the black plug from the end of the extension harness.

• Release the seal retainer• Use the WeatherPack Removal Tool

5

Installation

5. Route the loose pins end of the extension harness up thru the snout mounting plate from back to front.

6. Reinstall the connector removed in Step 4.• Flare latch wings on terminals slightly• A- Black• B- White• C- Green• Snap seal retainer shut

7. Route harness OVER pivot rod (See step 10 below) and forward to sensor.

8. Connect extension harness to sensor• Leave a bit of slack in the sensor tail • Secure connection with clamps on both sides• Make sure connector is tucked into corner of snout• Make sure connector latch faces UP against snout

9. Working from sensor back, secure sensor harness with clamps.

6

Installation

10. Secure harness around pivot as shown.• Make sure to leave enough slack for full motion of

snout

11. Route the cable around rear hinge as shown.• Leave enough slack for motion• Use zip tie on bar• Secure to lower plate with clamp and bolt

12. Route harness OVER the drive shaft assembly under trough, secure as necessary.

13. Follow existing cables to left side of header.

14. Connect extension harness to S84 on Insight adapter harness.

7

Installation

Insight Box Mounting

1. Mount Insight to existing slotted holes on back sheet of header.

• BCBOX Bolt Kit

Header Adapter Installation

1. Locate the adapter harness: QC1-AG12-XX.

2. Connect Y101 to the bottom of the Insight.

3. Locate the OEM connector “TO HEADER MOD - X08.62100” (12 pin Receptacle) .

4. Disconnect jumper plug or adapter to AGCO module from X08.62100. Store jumper in combine.

5. Connect Y548 to X08.62100.

6. If installing optional 3rd or 5th sensor, connect center sensor harness to S84.

Power Adapter Installation: Late Models

1. Choose Power Adapter (see Identify the Components).

2. Locate PFI-AG3300-P.

3. Locate the “CENTER POS SEN - X08.62094” (6 pin plugs for steering sensor) under center of head.

4. Tee power adapter Y573-Y574 into OEM plugs.

5. Route Y520 back toward the Insight box, following OEM harness.

6. Route Y521 on the Insight adapter down toward Y520, following OEM harness.

7. Connect Y520 to Y521.

8. Make sure to tie up all cabling securely.

8

Installation

Power Adapter Installation: Early Models

1. Locate power wire PFI-AG13-P.

2. Connect the power to a fuse in the cab fuse compartment.

3. If your fuse panel has “spare fuse” ¼” spades, remove the clip and connect the ¼” spade directly to the “Spare fuse” blade.

4. Otherwise snap clip around the output (fused) side of the AHC fuse.

5. Connect the ground ring to a bolt in the fuse compartmant.

6. Route Y520 out of the cab and down the feeder house to beside the single point.

Route Y521 on the Insight adapter up the single point harness to beside the single point.

7. Connect Y520, Y521 (you will need to disconnect everytime the header is disconnected.)

8. Make sure to tie up all cabling securely.

9

Calibration

Sensor Adjustment

Insert header stop to prevent movement

Changing Swing

1. Loosen the bolt A holding down stop.

2. Slide the down stop to new position in slotted hole.• Raising down stop will increase voltage swing and

allow higher maximum cutting height• Lowering the down stop will decrease total voltage

swing and help prevent arm from “stabbing” the ground when the headers is lowered

Increasing or Decreasing Voltage

1. Loosen sensor mounting nuts B.

2. Twist sensor to new position using slotted mounting holes.

• Twisting sensor clockwise will lower voltage• Twisting sensor counterclockwise will increase

voltage

3. Retighten the nuts B.

A

BB

10

Installation

Sensor Extensions

Headsight recommends using the lowest extension setting that allows you to run as high as you desire. Increasing the length of the extension will reduce header control sensitivity.

1. Remove flange locknut then remove arm and spring.

2. Install extension to sensor assembly with previously removed spring and flange locknut.

3. Install arm in extension with two bolts and nuts as pictured at desired length.

• Headsight does not recommend extensions unless you need to run higher

• If you desire to operate header higher than sensors will allow, you may add extensions

11

Parts

Parts

KIT - HT2291

ITEM QTY. PART NUMBER DESCRIPTION1 1 HT2000-B Corn Sensor2 1 B2290 Mounting Hardware3 1 HT2290 Mounting Bracket4 1 BCS1 Hardware/Extension Kit5 1 08300106 Pin Removal Tool6 1 PFB17 Extension Harness

1 32

5

4

6

12

Parts

ITEM QTY. PART NUMBER DESCRIPTION1 1 INSIGHT Insight Controller2 1 QC1-SG12-xx Main Harness3 1 BCIBOX Mounting Hardware4a AR PFI-AG3000-P Power Wire4b AR PFI-AG13-P Power Wire

Insight Kit

4b4a3

21

13

Parts

UN

LES

S O

THE

RW

ISE

SP

EC

IFIE

DD

IME

NS

ION

S A

RE

IN IN

CH

ES

DIM

EN

SIO

NS

W/O

TO

L A

RE

BA

SIC

THIR

D A

NG

LEP

RO

JEC

TIO

N

THE

INFO

RM

ATI

ON

CO

NTA

INE

D O

N T

HIS

DR

AW

ING

IS P

RO

PR

IETA

RY

TO

HE

AD

SIG

HT,

INC

. A

NY

UN

AU

THO

RIZ

ED

US

E O

F S

UC

H C

ON

TEN

TS IS

STR

ICTL

Y P

RO

HIB

ITE

D.

CH

G L

EV

EL

DATE

SH

EE

T

OF

HEA

DSIG

HT IN

C. C

12

34

D C B A

11

EFGH

D C B AEFGH

56

78

12

34

56

78

04H

T200

0_P

AR

TS

CO

RN

SE

NS

OR

PA

RTS

, HA

LL E

FFE

CT

JAN

30,

17

MA

TER

IAL

N/A

HT2

000_

PA

RTS

ITE

M N

UM

BE

RP

AR

T N

UM

BE

RD

ES

CR

IPTI

ON

QU

AN

TITY

1H

T212

5P

IVO

T A

RM

12

HT2

111

SP

RIN

G1

3H

T213

1B

US

HIN

G B

LUE

1

4H

T213

2B

US

HIN

G W

HIT

E1

5*H

T213

9B

US

HIN

G A

SS

EM

BLY

WIT

H S

EA

LS1

608

1001

03S

NA

P R

ING

E-C

LIP

17

HT2

120

CO

RN

BO

DY

18

HT2

128

SE

NS

OR

19

0820

0147

M

5x20

HE

X B

OLT

210

HT2

130

SH

IELD

(OP

TIO

NA

L)1

1108

2001

17M

8x12

FLA

NG

E B

OLT

111

A08

2001

17M

8x12

FLA

NG

E B

OLT

(OP

TIO

NA

L)1

12H

T210

5S

TOP

113

0820

0151

5/16

-18

FLA

NG

E L

OC

K N

UT

114

HT2

110

SP

RIN

G1

1508

2001

313/

8-16

SE

RR

ATE

D F

LAN

GE

NU

T2

16H

T211

7E

XTE

NS

ION

217

0820

0108

3/8-

16x1

-3/8

HE

X B

OLT

218

HT2

113-

BH

T211

3-Y

PO

LY A

RM

BLA

CK

PO

LY A

RM

YE

LLO

W1

19H

T200

0-B

HT2

000-

YC

OM

PLE

TE S

EN

SO

R A

SS

EM

BLY

BLA

CK

CO

MP

LETE

SE

NS

OR

AS

SE

MB

LY Y

ELL

OW

(AS

SM

EX

CLU

DE

S 1

0, 1

1A, 1

5, 1

6 &

17)

NO

TE: S

EN

SO

R C

ALI

BR

ATI

ON

TAR

GE

T H

IGH

VO

LTA

GE

= 4

.00V

(AC

CE

PTA

BLE

RA

NG

E 3

.95V

- 4.

05V

)

34

25*

14

13

11

126

10

18

1

11A

7

8

9

5*

5*5*

16

17

15

14

This PageIs Intentionally

Left Blank

15

STATEMENT OF LIMITED WARRANTY

For Headsight® Products Headsight Inc. (Headsight) warrants its new products to be free from defects in material and workmanship for a period of twelve (12) consecutive months following the date of purchase by the retail purchaser.

Headsight Inc. (Headsight) warrants its new corn sensors assemblies for a period of thirty-six (36) months.

Headsight warrants genuine Headsight replacement parts and components to be free from defects in material and workmanship for a period of six (6) consecutive months following the date of purchase or the remainder of the original equipment warranty period, whichever is longer.

Headsight’s obligation under these warranties shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in Headsight’s judgment, shows evidence of such defect.

Limitations to Warranty

This warranty does not cover:• Warranty claims directly resulting from improper installation of the product.• Any product damaged by accident, abuse, misuse, or negligence after shipment from Headsight.• Any unauthorized product alteration or modification.• Any unauthorized repairs made with parts other than genuine Headsight parts.• Any repairs performed by anyone other than Headsight or an authorized Headsight dealer unless specifically authorized

by Headsight.

Warranty Procedure• Troubleshooting should be done between farmer/dealer and Headsight through our technical assistance @

574.220.5511. • Labor reimbursement will occur only pre-arranged through Headsight technical assistance and be scheduled to a flat rate

basis or reasonable time allowance in Headsight’s judgment. • There is no mileage reimbursement. • Diagnostic time will not be reimbursed except in pre-arranged circumstances.• Warranty claims should be on typical dealer service work order with a number and name to be attached for any future

correspondence. • All warranty work must be performed, and claims submitted, within thirty (30) days of the occurrence of the claim and

within the warranty period.• All parts removed during warranty repair must be returned to Headsight with Headsight’s Return Form within thirty (30)

days of the occurrence of the claim and within the warranty period.• Headsight, Inc. reserves the right to either inspect the product at the original retail purchaser’s location or require it to be

returned to Headsight, Inc. for inspection.

Limitation of LiabilityHeadsight makes no express warranties other than those, which are specifically described herein. Any description of the goods sold hereunder, including any reference to buyer’s specifications and any descriptions in circulars and other written material published by Headsight is for the sole purpose of identifying such goods and shall not create an express warranty that the goods shall conform to such description.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. There are no implied warranties of merchantability or fitness of a particular purpose. This warranty states Headsight’s entire and exclusive liability and buyer’s exclusive remedy or any claim for damages in connection with the sale of furnishing of Headsight products, their design, suitability for use, installation or operation, or for any claimed defects herein. HEADSIGHT WILL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, NOR FOR ANY SUM IN EXCESS OF THE PRICE RECEIVED FOR THE GOODS FOR WHICH LIABILITY IS CLAIMED.

No representative of Headsight nor any dealer associated with Headsight has the authority to change the items of this warranty in any manner whatsoever, and no assistance to purchaser by Headsight in the repair of operation of any Headsight product shall constitute a waiver of the conditions of this warranty, nor shall such assistance extend or revive it.

Headsight reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. Warranty: 1/2017

P 574.546.5022 • F 574.546.57604845 3B Rd • Bremen, IN 46506info@headsight.comwww.headsight.com