Aeroxcraft DJI F550 Landing Gear Set Assembly · PDF fileF550 Landing Gear Assembly Manual V1.6 . Notes. The frame is made from 1.5mm G10 epoxy laminate. The thickness can vary slightly,

F550 Landing Gear Assembly Manual V1.6
Aeroxcraft DJI F550 Landing Gear Set
Assembly Manual
Designs, Images and Content Copyright Aeroxcraft Ltd. 2012 / 2013 1

Notes The frame is made from 1.5mm G10 epoxy laminate. The thickness can vary slightly, this is allowed for in the machining process, if however there is a problem the slots can be slightly opened up with a small file. It is the owners responsibility to ensure this model is assembled and fitted out correctly and safely. Ensure that your model is capable of safely and reliably lifting the payload you are asking it to. This model is dangerous if used in an incorrect manner. Ensure you seek assistance from an experienced flyer if you are unsure. Do not fly near people, property or highways. Do not fly over people, property or highways. There may be laws and regulations governing the use of this model in your area, seek advice from your authorities if you are unsure. Planning your build and installation is key to building a safe and reliable multi rotor. Make sure all wiring is of the correct gauge, properly connected, neat and protected from wear/tear and radio/electrical interference. Make sure all the components you use are suitable for the size and weight of your multi rotor. Do not over tighten screws. Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly and frequently during use. Do not use unless all components are correctly fitted and adjusted. Do not use if any parts are missing, damaged or broken. Assembly is required. Take care when unpacking and assembling; contains small parts and sharp edges. If you require any replacement parts they are all available from Aeroxcraft. Contact us for details.
Contact details Email [email protected] Website www.aeroxcraft.com
mailto:[email protected]://www.aeroxcraft.com/

Package contents Qty Item 2 Leg Plate 2 Leg Spacer Plate 2 LED Bracket 1 Battery plate - Front 1 Battery plate - Rear 2 Leg Bracket - Aluminiun 4 Aluminium Tubes 6 M3 x 8 Screw 2 M3 x 6 Screw 6 M3 Nyloc Nut 1 M3 x 15mm Plastic Hex Spacer 16 16mm Grommet 8 12mm Endcap 30 Cable Tie 4 M6 x 16 Nylon Screw 8 M8 Nylon Washer 4 8mm Nylon Bush 4 M6 Nyloc Nut 2 12mm pipe clamp 2 30cm Velcro battery straps 2 20cm Velcro battery straps Note: As of Sept 2013 the landing gear includes a universal mounting that can be used for the Original Aeroxcraft GoPro Gimbal (servo gimbal), the Zenmuse H3 2D, and many others. There is also a mounting that can be used for attaching a small auxiliary FPV camera.

Step1

Step2 8x 16mm Grommets

Step 3 6x M3 Nut, 6x M3x8 Screws, 2x Leg brackets

Step 4 4x 16mm Grommets
Step5

Step 6 2x M3x6 Screws, 1x M3 Hex spacer

Step 7 2x Aluminium Tubes

Step 8 4x 12mm Endcap
Step 9 2x Aluminium Tubes

Step 10

Step 11 2x 12mm Pipe clamps. Use the pipe clamps to ensure the batteries and camera cannot slide off the ends of the payload rails. If you need more clamps they are available from Aeroxcraft.

Step 12 4x M6 Screw, 4x Nylon Bush, 8x Washer, 4x M6 Nut

Universal Mount (Included with landing gear kit as of Sept 2013, also available as separate item.) The hole pattern matches the Zenmuse H3 2D. Front plate can be used for mounting auxiliary FPV camera.
Assembly ManualNotesContact details

Documents

Aeroxcraft DJI F550 Landing Gear Set Assembly · PDF fileF550 Landing Gear Assembly Manual V1.6 . Notes. The frame is made from 1.5mm G10 epoxy laminate. The thickness can vary slightly,