ADX MMO Laser Gaming Mouse ADXLM0418 Manual MMO Laser...Safety Warnings While the mouse is functioning, the laser beam is not visible to the naked eye. Avoid looking directly into

FIREPOWER M04RGB MMO LASER MOUSEINSTRUCTION MANUALADXLM0418

Contents

Safety Warnings ................................................................................. 4

Unpacking .......................................................................................... 5

Product Overview .............................................................................. 6

Adjusting the Weight ........................................................................ 7

System Requirements ....................................................................... 8

Software Installation ......................................................................... 8

User Interface ..................................................................................... 8

Buttons Setting .................................................................................. 9

Customising the Buttons ................................................................ 10

Master Controls Setting .................................................................. 15

Macro Setting ................................................................................... 16

General Setting ................................................................................ 17

Hints and Tips................................................................................... 18

Specifications ................................................................................... 18

Safety WarningsWhile the mouse is functioning, the laser beam is not visible to the naked eye. Avoid looking directly into the emitter hole while the mouse is active.

• Your product complies with CE rules.• This product has no serviceable parts. Use of controls or

adjustments of procedures other than the Instruction Manual may result in danger.

5

UnpackingRemove all items from the packaging. Retain the packaging. If you dispose of it please do so according to local regulations.The following items are included:

Thank you for purchasing your new product.We recommend that you spend some time reading this instruction manual in order that you fully understand all the operational features it off ers. You will also fi nd some hints and tips to help you resolve any issues.Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Main Unit

Setup Disc x 1 Instruction Manual

InstructionManual

Rounded Weight Container x 1

6

1. Right Button

2. Scroll Wheel

3. Left Button

4. Profile ButtonSelect profile 1-5.

5. DPI ButtonSelect different dpi.

1

2

3

6. DPI LED

7. Weight Compartment

8. Forward/Backward Buttons

9. Sniper Button

10. Customise Buttons

Product Overview

4 5 6 7

89

10

7

Adjusting the Weight6 x 5.7 gram of metal weights are provided for you to select your ideal mouse weight up to 34.2 gram

1. Lift the weight compartment up.

2. Adjust to the weight you want.

3. Store the remaining weights in the rounded weight container.

8

System RequirementsOperating Systems: Microsoft® Windows® 7 / 8 / 10Hardware: 1 available USB port

CD rom for gaming software installation

Software Installation1. Insert the provided Setup Disc into the computer’s CD rom.2. It will auto run the setup software, otherwise choose

ADXLM0418_setup.exe from your CD drive.3. Follow the installation instruction to complete the installation.4. Choose ADXLM0418 Configuration.exe from the desktop to

start the software.

User InterfaceChoose ADXLM0418 Configuration.exe from the desktop to start the software.

1. Setting options.

2. Minimise the software.

3. Exit the software.

SETTINGSMACRO EDITORDPIBUTTONS

Profile 1 Profile 2 Profile 3 Profile 4 Profile 5

No function

Right click

Wheel click

Scroll down

DPI loop

Scroll up

Left clickForward

Back

Sniper functionX:400 Y:400

No function

No function

No function

No function

1 2 3

9

Buttons SettingSelect BUTTONS from the user interface.

1. ProfileYou can save 5 different profiles with customising the buttons. Different colour indicates different profile.

Profile renameProfile can be renamed followed by a double click.

Enter profile name

Magic Casting

OKCancel

2. Customising the Buttons• Change the mouse button into desired functions from the

function list.• Left click cannot be customised unless another left click is

set.

3. Quick ApplyClick to quick apply with desired keyboard keypress or mouse button to replace with.

4. ColourSelect desired LED colour.

5. Trash• Drag the button with customised setting to will reset to

default.• Drag the button with default setting to will disable the

function.


Profile 1 Profile 2 Profile 3 Profile 4 Profile 5

No function

Right click

Wheel click

Scroll down

DPI loop

Scroll up

Left clickForward

Back

Sniper functionX:400 Y:400

No function

No function

No function

No function

1

4

2 3

5

10

Some functions are not available for specific mouse button.

Customising the ButtonsClick on the mouse button you wish to customise, the options will be show as below. A chosen function icon will be highlighted then click SELECT to confirm.

1. Mouse Functions

1. Left click

2. Right click

3. Wheel click

4. Forward

5. Back

6. Scroll up

7. Scroll down

8. Tilt left

9. Tilt right

10. Universal scroll

11. Double left click

12. Triple left click

13. Fire buttonClick and hold to continue fire.

14. On-to-go fireClick and hold to enable on-to-go fire. At the same time, click on any other button to fire continuously.

Customise functionDefault function

MOUSE FUNCTIONS KEYBOARD FUNCTIONS ADVANCED FUNCTIONS MACRO KEY CYCLE

DEFAULT CANCEL SELECT

Left click Right click Wheel click Forward Back Scroll up Scroll down

Tilt left Tilt right Universal scrolling Double left click Triple left click Fire button On-to-go fire

[Right click] : Right click

1

8

2

9

3

10

4

11

5

12

76

13 14

11



Ctrl

Shift

PrtSc SrcLk Pause

Caps Lock

Tab

Shift

CtrlAppWinAltWin Alt

Insert Home PgUp Num

Delete End PgDn


1 82 93 104 11 12 135 76

1. Web browser

2. Calculator

3. Media player

4. Mute

5. Volume down

6. Volume up

7. Play/pause

8. Play

9. Pause

10. Fast forward

11. Next track

12. Previous track

13. Stop


2. Keyboard FunctionsCustomising mouse button can choose keypress from keyboard or other media functions as below.

12


No function

Angle snappingon/off

Launch drivermenu Adjust lift-off Adjust DPI Lock Y-axis Lock X-axis Sniper function

DEFAULT CANCEL SELECT[Right click] : Right click

DPI Decrease DPI loopDPI Increase


1. No FunctionDisable the current mouse function.

2. Launch Driver Menu

3. Adjust lift-offClick and hold to access lift function.

4. Adjust DPIClick to turn on DPI menu, and then use scroll up/down to adjust DPI.

5. Lock Y-axisClick and hold to allow cursor to move horizontally only.

6. Lock X-axisClick and hold to allow cursor to move vertically only.

7. Sniper Function• Click and hold to use

sniper function with presetting DPI.

• Release to resume normal.

8. Angle Snapping on/offHelp to draw a horizontal or vertical straight line.

9. DPI Increase

10. DPI Decrease

11. DPI Loop

1

8

2

9 10 11

3 4 5 76

3. Advanced Functions

Some functions are not available for specific mouse button.

13

• Do not lift the mouse off the surface while the setting is in progress.

• If setting error occur, adjust again.

Lifting the mouseThis function is designed for repositioning the mouse and has no effect on gameplay. Mouse sensor will stop transmitting movement data after the set a Lift off distance is exceeded.

To adjust the lifting function:1. Select a Lift function to a desired button.2. Put the gaming mouse on the desired surface.3. Move the mouse over the chosen surface as thoroughly as

possible while pressing and holding the Lift button.4. The DPI LED will blink while the setting is in progress. The

DPI LED will stay on when setting is finished. Release the Lift button.

Distance between mouse and surface

14

KEY CYCLE TYPE KEY CYCLE

Cycle


DEFAULT

Add CLEAR

CANCEL SELECT

Reverse cycle

Current position




MACRO EDITOR

Attack Mode

Attack Mode

SpecialAttack

1. CycleClick customised mouse button to type out added keypress in sequence.

2. Reverse CycleClick customised mouse button to type out added keypress in reverse sequence.

1. Macro listChoose a macro and press SELECT to confirm.

4. Macro Functions

5. Key Cycle FunctionsKey cycle can add up to 5 keyboard keypress.

1

2

12

3

4 5

3. Current PositionClick customised mouse button once to type out 1 keypress each time in sequence.

4. AddAdd a keypress.

5. ClearClear all keypress.

2. Macro EditorClick to enter MACRO EDITOR section for editing.

15

Master Controls Setting

Select DPI from the user interface.

1. DPI SettingSensitivity (DPI) pertains to how much effort is needed to move the mouse pointer in any direction. The higher the DPI, the faster the mouse movement.The X-axis (horizontal) and Y-axis (vertical) use the same sensitivity values.

2. AutoSensitivity (DPI) will change depending on your mouse movement. The faster the mouse movement, the higher the DPI.

3. X-Y SensitivityYou may set different sensitivity values to each of the axis by selecting X-Y axis Independent.


X/Y axis independent

X 800

Y 800

X 1600

Y 1600

X 3200

Y 3200

X 12000

Y 12000

Auto

Auto

Auto

Auto

21

3

16

Create new macro Delete current item

MACRO EDITOR

MACRO TYPE One-time modeMouse memory (Free 7064 bytes)

Record delays

Attack Mode

Attack Mode

SpecialAttack

34 bytes

34 bytes

34 bytes

Macro SettingBy assigning a macro to a mouse button, you can execute complex combinations with ease.

Select MACRO EDITOR from the user interface.

1. Macro ListA list of macro profile.

2. Macro TypeChoose a macro type.One-time mode: macro will run once.Loop mode: click once to start looping the macro, click again to stop.Firekey mode: macro will repeat as long as the button is clicked.

3. Create New MacroCreate new macro profile.

4. Delete Current ItemDelete selected macro or command.

5. Record DelaysInsert time delay between each command while recording macro.* Delay (1sec = 1000ms)

6. Macro Tool Bar

Insert delay

Insert keyboard, mouse or scroll command

Insert mouse movement

Record keyboard and mouse commands

Stop record

Import macro from file

Export current macro to file

Save macro

Clear command list

Remove selected command or drag & drop command here to remove it.

1

2

3 4 5

6

17

SAVE LOAD RESET


Angle snapping

500HzPOLLING RATE

GENERAL OPTIONS

INFORMATION

DIVER SETTINGS

Model: Dirver version:Firmware Version

Enable DPI/profile OSD

Disable mouse acceleration (OS)

General Setting

Select SETTINGS from the user interface.

1. Polling RateThe higher the polling rate, the more often the computer receives information about the status of your mouse, thus increasing the mouse pointer’s reaction time.You can select among 125Hz (8ms), 500Hz (2ms) and 1000Hz (1ms).

2. Angle SnappingSnapping function helps to move cursor in horizontal or vertical straight line.

3. Enable DPI/profile OSDDisplay on screen when changing to different DPI or profile.

4. Disable Mouse Acceleration (OS)Acceleration increases the cursor’s movement speed depending on how quickly the mouse is moved. Tick to disable this function.

5. SaveSave the current setting.

6. LoadLoad the saved setting.

7. ResetRestore to default setting.

1

23

4

5 6 7

18

Hints and Tips• Make sure the USB plug is fully plugged into a USB port and

the computer is on or try to use a different USB port.• If the mouse is moving erratically, change the working surface

which the mouse is operating on.• If the software is not working properly, uninstall it and then

reboot the computer. Re-install the software.

Specifications

Model ADXLM0418

Working Voltage DC 5V

Resolution 50 – 12,000 dpi

Dimensions (L) x (W) x (H) 133 x 78 x 43 mm

Net Weight 150g + (5.7g x 6)

Features and specifications are subject to change without prior notice.

19

For general information about this appliance and handy hints and tips, please visit: www.TeamKnowhow.com/discover or call 0344 561 1234

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0344 800 3456 (UK customers only). Calls charged at National Rate.

The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the

time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

All trademarks are the property of their respective owners and all rights are acknowledged.

IB-ADXLM0418-180529V1

DSG Retail Ltd. (co. no. 504877)1 Portal Way, London, W3 6RS, UK

Documents

ADX MMO Laser Gaming Mouse ADXLM0418 Manual MMO Laser...Safety Warnings While the mouse is functioning, the laser beam is not visible to the naked eye. Avoid looking directly into