View
248
Download
3
Tags:
Embed Size (px)
Citation preview
Advanced Tool ManagementInformation Module
Advanced Tool ManagementInformation Module
Using the Advanced Tool Management Display
Using the Advanced Tool Management Display
In the HAAS CONTROL
In the HAAS CONTROL
Press WRITE/ENTER to displayThe previous tool group’s data.
PRESS
THREE TIMES TO GET TOTHIS PAGE
If VQC ProbingIs not selected
SLIDE LEGENDSLIDE LEGEND
UPPER CASE (WHITE) - ACTION YOU WILL TAKEUPPER CASE (WHITE) - ACTION YOU WILL TAKE
UPPER CASE (ORANGE) - INSTRUCTIONSUPPER CASE (ORANGE) - INSTRUCTIONS
KEYS 0N THE CONTROLKEYS 0N THE CONTROL
UPPER AND LOWER CASE (BLUE) - INFORMATIONUPPER AND LOWER CASE (BLUE) - INFORMATION
The ADVANCED TOOL MANAGEMENT DisplayThe ADVANCED TOOL MANAGEMENT Display
• Improves on operator’s capability to monitor and control tool life
• Allows grouping of tools to facilitate lights out machining
• Available starting in Software version 13.4
• Activated by Parameter 315
• Improves on operator’s capability to monitor and control tool life
• Allows grouping of tools to facilitate lights out machining
• Available starting in Software version 13.4
• Activated by Parameter 315
LET’S TAKE A LOOK AT HOWLET’S TAKE A LOOK AT HOW THIS DISPLAY CAN BE USEDTHIS DISPLAY CAN BE USED
LET’S TAKE A LOOK AT HOWLET’S TAKE A LOOK AT HOW THIS DISPLAY CAN BE USEDTHIS DISPLAY CAN BE USED
Duplicate or backup tools can be classified into specific groups. The programmer specifies a group of tools instead of a single tool in the G-code program. ATM will track the usage of individual tools in each tool group and compare it to user defined limits. Once a limit (e.g. number of holes drilled or tool load) has been reached, the mill will automatically choose one of the other tools in the group the next time that the tool is needed.
PRESS
TOENTER
CURRENT COMMANDS DISPLAYS
PRESS
UNTIL YOU REACH THE ADVANCED
TOOL MANAGEMENT
SCREEN
In the upper left is the “TOOL
GROUP” window. In the lower
right, there is a help dialog.
Press WRITE/ENTER to displayThe previous tool group’s data.
<PREVIOUS>
PRESS
TWICE To <ADD>
You can now enter the
number of a new Tool
Group for a particular tool The number
must be between 1000
and 2999.
Enter a four digit number and pressWRITE/ENTER to create a new toolGroup.
<ADD>
ENTER
1234and
PRESS
You now have a new Tool Group numbered 1234 for a particular
tool.
( Example)
Enter a four digit number and pressWRITE/ENTER to create a new toolGroup.
1234
<ADD>
PRESS
to
GROUP USAGE
You can select either “IN ORDER” “NEWEST” “OLDEST”
for how tools within the group are selected.
IN ORDER
Determines how the tools in the groupare to be used.Use the LEFT/RIGHT arrow key to changeAnd press WRITE/ENTER to select.
1234
PRESS
to
DESCRIPTION
Here you can enter a short
description of the tool
group (e.g. .5 in. ball end
mill).Contains the operator’s description of the current tool group.Type in the description and pressWRITE/ENTER to record.
1234
PRESS
This switches you to the
next window where you can define
the tool limits.
In “USAGE” you can enter the maximum
number of times you
want a tool to be used.
The maximum number of times a toolcan be used.Enter the number of times a toolcan be used and press WRITE/ENTER.
1234
PRESS
to
HOLES
In this block you can enter
the max. number of
holes a tool in the group can drill, tap,
or bore.
The maximum number of holes a toolcan drill.Enter the max number of holes andpress WRITE/ENTER.
1234
Note: A tool will not be expired while in use. If you have a Drill canned cycle of 20 holes and you set the max. holes to 18, the same tool will be called up a second time. Therefore, it will actually drill 40 holes.
PRESS
to
FEED TIME
Here you can enter the
maximum FEED TIME you want
each tool to be used.
The allowed feed time for each toolin this group.Enter the allowed time in minutesand press WRITE/ENTER to record.
1234
PRESS
to
TOTAL TIME
In this block you can enter
the total allowed time for each tool in the group to be used.
The allowed total time for each toolin this group.Enter the allowed time in minutes and press WRITE/ENTER to record.
1234
PRESS
to
TOOL LOAD
Here you can enter the
max. percent of spindle
load that you want the tools to
withstand before a TL ACTION takes place.
Allowed load limit for tools in thisgroup before TL Action takes effect.Enter the max. allowed load and press WRITE/ENTER to record.
1234
PRESS
toTL ACTION. In this block
you can choose the action that you want taken when the value in TOOL LOAD is exceeded. Choices are “ALARM”,
“FEED HOLD”, “BEEP”, &
“AUTOFEED”
ALARM
The action to take if the allowed tool load is exceeded.Press LEFT/RIGHT to select and press WRITE/ENTER to record.
PRESS
This switches the active window to
TOOL DATA.
In this area you can enter
the tool numbers in this group.
Holds the tool number of the tools inthe group. Enter a tool number thenpress WRITE/ENTER. Enter 0 to clear. Press ORIGIN to clear tool usage data.
ENTER
1and PRESS
Note that the
the data in the right hand
section is filled in and
100% is entered under “LIFE”. This indicates the tool has not been used.
Holds the tool number of the tools inthe group. Enter a tool number thenpress WRITE/ENTER. Enter 0 to clear. Press ORIGIN to clear tool usage data.
PRESS
By entering
an asterisk in the “EXP”
column you can manually
“Expire” a tool, and its
“LIFE” will go to Zero.
Indicates the user has determinedthat this tool is expired or worn out.To expire at tool enter ‘*’ and press WRITE/ENTER. To clear press WRITE/ENTER
When all the tools in a group are expired, the next time the tool group is called up you will get a 471 “Out of Tool” alarm.
PRESS
The data under
“CRNT PKT” cannot be changed.
It shows the pocket the
selected tool is in.
PRESS
The H Code cannot be changed if Setting 15
is ON.Use the
Group ID with the H code in your program (i.e. H1234).
1
Normally this is the tool number inthe offset table, to change to a different number turn setting 15 off.
PRESS
The D Code cannot be changed if Setting 15
is ON. Use the
Group ID with the D code in your program (i.e. D1234).
1
Normally this is the tool number inthe offset table, to change to a different number turn setting 15 off.
PRESS
You enter the
number of flutes the tool
has in this space.
This also updates theTool Offset
data page. It defaults to 2.
2
Displays the number of flutes on thetool. Enter the number of flutes andpress WRITE/ENTER. Press ORIGIN to clear
PRESS
This shows how many
holes a tool has drilled.
You can change the
value or reset by pressing
<WRITE/ ENTER> or <ORIGIN>.
0
Displays the number of holes the toolHas drilled. Enter a new number orPress ORIGIN to clear.
PRESS
This shows
the amount of time a tool
has been in a feed. You can
change the value or reset by pressing
<WRITE/ ENTER> or <ORIGIN>.
0:00:00
Displays the amount of time the toolhas been used in a feed. To change, enter the time in minutes and press WRITE/ENTER.
PRESS
This shows the total
time the tool has been used. You
can change the value or
reset by pressing <WRITE/
ENTER> or <ORIGIN>.
0:00:00
Displays the total time the tool hasbeen used. To change, enter the time in minutes and press WRITE/ENTER.
PRESS
This shows how many times a tool
has been used. You
can change the value or
reset by pressing <WRITE/
ENTER> or <ORIGIN>.
Displays the number of times the toolhas been used. Enter a new number or press ORIGIN to clear.
0
PRESS
This shows the maximum load the tool has had. You can change the value or
reset by pressing <WRITE/
ENTER> or
<ORIGIN>.
0
Displays the maximum load that the tool has had. Enter a new number or Press ORIGIN to clear.
ProgrammingProgramming
• T1234 M06; (Calls up a tool in group 1234)
• G43 H1234 Z1.0 (Sets the tool length offset for the tools in group 1234)
• #8001 = 1 (Expires tool 1)• #8001 = 0 (Makes tool 1 available if
expired manually or with macro)• The Macro statements can only be
used with the macro option. Macros 8001-8200 represent tools 1-200.
Prepared by Haas AutomationTraining DepartmentOxnard, CA 93030