Upload
others
View
28
Download
0
Embed Size (px)
Citation preview
Project ID #: ES025
Advanced Electrolyte Additives for PHEV/EV Lithium-ion Battery
Zhengcheng Zhang (PI) Lu Zhang, Kyrrilos Youssef and Khalil Amine
Argonne National Laboratory
Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting
Washington, D.C. May 14-18, 2012
This presentation does not contain any proprietary, confidential, or otherwise restricted information
2
Project start date: FY09 Project end date: FY14 Percent complete: 20%
Timeline
Budget
Barriers
Partners
Project Overview
Total project funding - 100% DOE funding Funding received in FY11: $300K Funding for FY12: $400K
Electrolyte/electrode surface reactivity Battery cycle life & calendar life Battery abuse tolerance
US Army Research Lab University of Utah Center of Nanoscale Materials (ANL) Industrial Partners: ConocoPhilips,Saft,
EnerDel. Project Lead - Zhengcheng Zhang
3 3
To develop an efficient, inexpensive functional electrolyte ADDITIVE
technology to address the barriers existing in the current lithium ion battery system such as poor cycle life, calendar life and battery abuse tolerance.
To establish the ADDITIVE structure-property relationship by screening a variety of existing chemical compounds and develop (design, synthesize and evaluate) brand new electrolyte additives having superior performance with the aid of the theoretical modeling.
FY11’s objective is to continue to evaluate and categorize the existing chemical compounds as possible SEI ADDITIVE to stabilize the carbonaceous anode/electrolyte interphase and to develop novel SEI additives using organic synthesis based on the knowledge gained in the screening.
Project Objectives
4
Technical Approach Screen, identify and evaluate a large number of various functional
compounds containing cyclic and double bond structures, including oxalic, carboxylic anhydride, vinyl, heterocyclic containing compounds based on the empirical rule of Degree of Unsaturation (DU) as potential electrolyte additives.
Combine quantum chemical calculation (DFT and MD) and electrochemical experimental testing to select the compounds that can be reductively decomposed prior to the formation of conventional SEI layer at 0.5~0.8V vs Li/Li+.
Evaluate the battery performance of the best additive screened using LiNi1/3Co1/3Mn1/3O2/MCMB full cell testing vehicle: the capacity retention with cycling at various temperatures, storage property at elevated temperature, impedance growth with cycling, and cell power capability.
Propose the mechanisms of the SEI formation by the new additive with the aid of theoretical calculation method and provide insights for the next step research of advanced additives.
5
Pristine Lithium uptake Lithium removal
Lithium anodes - Instantaneous SEI formation in contact with electrolyte Carbonaceous anodes: Stepwise formation, potential dependent and co-intercalation of Li and
electrolyte (1990s, Dahn’s findings ) Lithiated graphite (LiC6) is thermodynamically unstable in contact with the electrolyte component
including electrolyte solvent, lithium salt, impurities… Lithiated graphite (LiC6) is dynamically stable in contact with the electrolyte due to the existence of
solid electrolyte interphase (SEI) layer formed at the electrolyte/electrode interphase during the first charging process.
SEI Formation Process of Graphite Based Anode
Technical Accomplishments
6
1. SEI Additive to Enable Li-ion Cell Operation: For new electrolytes (i.e. PC based electrolyte), the SEI additive is mandatory and indispensible for cell performance. SEI is formed on graphite anode surface to prevent the electrolyte solvent co-intercalation and carbon exfoliation with gas evolution. 2. SEI Additive to Improve Li-ion Cell Performance: For conventional electrolyte (for example 1.2M LiPF6 EC/EMC 3/7), the SEI additive is the performance improver. Artificial SEI forms prior the regular SEI and suppress the formation of the regular SEI. A brand new artificial SEI is formed (A-SEI) New SEI forms in addition to the formation of regular SEI. A dual SEI is formed (D-SEI).
SEI Additive Category and Function
ADDITIVE
7
Degree of Unsaturation
Chemical Formula
Degree of Unsaturation
Chemical Formula
2
6
3
7
4
9 5
OO
O
O O
O
OO
O
O
BOO
O
F
FLi
O
O O
O OO
O
O
ON
OB
OO
O
O
O O
O
LiO
OO
O O
ON
O
O
PO
OO
O
O
OO
OO
OO
O
Li
Rings count as one degree of unsaturation. Double bonds count as one degree of unsaturation. Triple bonds count as two degrees of unsaturation.
Degree of unsaturation (DU) should be more than two. The higher the degree of unsaturation, the better the performance of additive?
SEI Additive Selection Rule
Screening Results: Empirical rule was established to help generate the screening list of SEI additive candidates and an evaluation procedure using LiNi1/3Co1/3Mn1/3O2/MCMB chemistry was chosen. As a result, several promising SEI additive candidates (A1-A7) stand out with superior features in terms of improving cell cyclability and impedance.
Mechanism Study: New SEI additives (ANL-SEI-1, 2, 3) were chosen to conduct further investigation due to their promising performance. Many surface characterization techniques, such as FT-IR, Raman, SEM, and XPS, were employed to understand the mechanism of the SEI formation process.
Novel SEI Additive Development: Based on the knowledge gained during the first two phases, novel cyclic phosphate compounds were designed and synthesized as new SEI additives. Chemical structure of the phosphates was characterized by 1H, 13C and 31P-NMR and GC-MS. Evaluation of lithium ion cell performance demonstrates promising results.
8
Achievements and Progress
EC A1 A2 A5 A6 A7
OO
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
ANL-SEI-1 ANL-SEI-2 ANLSEI-3 EMP
Cyclic Phosphate Compounds N
N
N
O
O O N
N
N
O
OO
9
Potential (V, vs Li+/Li) Potential (V, vs Li+/Li)
Potential (V, vs Li+/Li) Potential (V, vs Li+/Li) Potential (V, vs Li+/Li)
SEI Formations at Different Potentials (vs Li+/Li)
0.49V
0.54V 0.60V 0.64V
0.2 0.6 1.0 1.4 1.8 2.2
2.10V
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
1.60V
-0.001
-0.001
0.000
0.000
0.0000.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
dQ
/d
V 1.24V
Li/Graphite half cell 1st cycle differential capacity profiles: 1.2M LiPF6 EC/EMC 3/7+1% Additive at RT using C/10 rate.
O
O
OO
BOO
O
O
O O
O
Li
N
N
N
O
OO
PO
OO
O
O
OO
OO
OO
O
Li
OO
O
OO
P
O
R
10
0.00.20.40.6
0.0
0.2
0.40.0
0.2
0.4
2.00 2.25 2.50 2.75 3.000.0
0.2
0.40.0
0.2
0.4
Gen 2
0.2 w % OBD
0.1 w % OBD
1.0 w % OBD
0.4 w % OBD
Cell Voltage, VdQ
/dV,
mA
h/V
Additive Concentration Effect on SEI Formation Process and Cell Cycling Performance
o Capacity retention of MCMB/NMC cells in Gen2 electrolyte with or without additive A3 (left). The cells were cycled at 55◦C with 1C rate, cut-off voltages: 2.7 ~ 4.2 V.
o At 55oC, low concentration of additive A3 showed much improved capacity retention with cycling. o However, the high concentration of additive forms a thick SEI film leading to the high cell resistance. o 1st Cycle differential capacity profiles (dQdV) of NMC/MCMB cells (right) indicated different SEI
formation process with various additive concentrations.
0 50 100 150 2000.0
0.5
1.0
1.5
2.0
2.5
3.0
Dis
char
ge C
apac
ity (m
Ah)
Cycle Number
Gen 2 electrolyte 0.1 w% ANL-1 0.2 w% ANL-1 1.0 w % ANL-1
55oC
O
O
O
A-3
EE"
Before cycling
After cycling
Cell Impedance Variation with SEI Additive ANL-SEI-1
Impedance profiles of MCMB/NMC cell before cycling at 25°C; The Rb is smaller for the additive cell indicating the more conductive SEI layer formed compared to that of the pristine electrolyte. Unlike most of the existing commercial additives that show high initial interfacial impedance, ANL-Additive 3 shows similar initial interfacial impedance as the one without additive (stable and thin SEI).
12
2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600
66
77
88
99
66
77
88
99
66
77
88
99
52
65
78
91
Wave Number (cm-1)
Gen2
0.2% A-3 in Gen2
1% A-3 in Gen2
A-3 Additive
2000 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600
1.0% A3
Gen2
0.2% A3
850 cm-11760 cm-1 1475 cm-1
1154 cm-1
Wavenumbers (cm-1)
FT-IR Characterization of SEI Formed on Graphite Electrode Surface
OO
O
O
O O
O
O
O
FT-IR spectra of graphite electrode surface after 2-cycle formation. Measurement was performed in an Ar glove box.
Gen2 and Additive A3 IR spectrum as reference
Transmission %
13
XPS spectra of C1s, O 1s, F 1s, and Li 1s core peaks of the MCMB electrodes from MCMB/NCM coin cells containing different amounts of A3 additive in the electrolyte of 1.2M LiPF6 with ethylene carbonate/diethyl carbonate (3:7 weight ratio) after 2-cycle c/10 formation .
XPS Analysis of the New SEI Formed on Graphite
C1s O1s
F1s Li1s
14
Proposed SEI Formation By Additive Reductive Decomposition
OO O
OO O
O
O
O
OOO
OO
O
O
HC CH
O O
O OO
A3 3-oxabicyclohexane-2,4-dione
1.04 V
open C-O e-
0.66 V
Open C-C
1.02 V
H transfer
2.75 V Citraconic anhydride anion radical
1.93 V
Itaconic anhydride anion radical
1.21 V
1.81 V
open C-C
H transfer
3,6-dihydro-2H-pyran-2,6-dione anion
Polymerization
O
HC
O
O
CH2
E%"
citraconic anhydride dianion dimer
2e
X\aP#L']",B"
Dianion dimer
2-
X\aP#L'%",B"
2-
Two Favorable Polymerizations Pathways of ANL-SEI-1
16
500 1000 1500 2000 2500 3000 3500
0
1000
2000
3000
4000
5000
Inte
nsity
Wavenumber (cm-1)
Pristine Graphite
D
1331
G 1576
2D2664
2464G+D ?2931
16212x1621
200 400 600 800 1000 1200-1000
-500
0
500
1000
1500
2000
Inte
nsity
Wavenumber (cm-1)
743
905
470254 868
C_3, 10 scans, T=50secPristine Graphite
This is the expanded scan 200 and 1200 cm-1. The peaks at 254, 470, 743, and 905 cm-1 come from the SEI layer.
200 400 600 800 1000 1200-500
0
500
1000
1500
Inte
nsity
Wavenumber (cm-1)
8661125
C_7, 200-1300 from the pristine graphite
Pristine Graphite
200 400 600 800 1000 1200
5000
10000
15000
20000
25000
30000
35000
Inte
nsity
Wavenumber (cm-1)
481
625 704
793
918
1072
514 nm laser, A3 sample, SEI layer
Additive Graphite
Raman Characterization of New SEI Formed on Graphite
17
Synthesis of New SEI Additives Which Can Improve the Cycle Life with Controlled Impedance
Improve the cell cycle life is usually based on the sacrifice of impedance.
Synthesize novel SEI additives that not only can improve the cell performance, but also control the impedance growth.
“Efficient” additives should be able to help form stable SEI layer without a lot impedance increase.
An “efficient” additive should have multiple cyclic or double bond structures so that it could easily form into a polymeric film on the electrode surface.
An “efficient” additive should be reductively decomposed prior to the formation of the traditional SEI.
ANL-SEI-2 & ANL-SEI-3
18
Capacity Retention Profile of ANL-SEI-2 Compared with Gen 2 Electrolyte
ANL-SEI-2: 1,3,5-triacryloylhexahydro-1,3,5-triazine N
N
N
O
O O
0 20 40 60 80 100 120 140 160 180 2000.4
0.8
1.2
1.6
2.0
2.4
Capa
city
(mAh
)
Cycle number
Gen2 electrolyte With 0.1% ANL-2 With 0.2% ANL-2 With 0.3% ANL-2
0.64V
E("
Impedance Profiles for Cells with ANL-SEI-2
AC impedance profile of MCMB-1028/Li1.1[Ni1/3Co1/3Mn1/3]0.9O2 coin cells in 3E7EMC/PF12 with or without additives. The cells were charged to 3.8 V. The charge rate was 1C.
Before cycling After cycling
!^"
0.0ev 0.36 eV
-1.49 eV Red. Pot. Theor. 1.65 V
EA=0.86 eV
Red. Pot. Theor. 1.97 V Transition state
0.12 eV 0.0 eV
-1.75 eV
Energetics of ANL-SEI-2 Reductive Decomposition
ANL-SEI-3
ANL-SEI-2
Cell Performance of Synthesized Additive Cyclic Phosphate (in progress)
!E"
Capacity retention of MCMB/NMC cells in 3E7EMC/PF12 with or without various amount of EMP additives. The cells were cycled at 55 !C. The charge rate was 1C.
AC impedance profile of MCMB-1028/Li1.1[Ni1/3Co1/3Mn1/3]0.9O2 coin cells in 3E7EMC/PF12 with or without additives. The cells were charged to 3.8 V. The charge rate was 1C.
Before cycling After cycling
22
Collaborations and Interactions with Other Institutions
o Center of Nano-Materials at Argonne (DOE Lab) - Dr. Larry Curtiss and Dr. Paul Redfurn for DFT calculation of reduction potentials of additives and SEI formation mechanism. - Dr. Hsien-Hau Wang for the Raman and AFM measurement. o University of Utah - Professor Fang for SEI characterization by XPS. o US Army Research Laboratory (DOD Lab) - Dr. Richard Jow and Dr. Kang Xu for technical and information exchanges. o ConocoPhilips, Saft and EnerDel - Electrode supply.
23
Proposed Future Work
For the rest of this fiscal year and FY13, we are proposing the following research work:
o Continue to develop additives with the aid of the quantum chemical
models and the electrochemical screening of the list of selected compounds and expand the SEI additive database.
o Design and synthesize suitable SEI additives.
o Conduct extensive electrochemical performance evaluation using selected lithium ion battery chemistry.
o Extend electrolyte additive research into other areas including overcharge protection additive (redox shuttle) and cathode additive.
24
PHEV and EV batteries face many challenges including energy density, calendar life, cost, and abuse tolerance. The approach of this project to overcome the above barriers is to develop advanced electrolyte additive that can stabilize the electrode/electrolyte surface and significantly improve the cell cycle life and calendar life without sacrificing the safety to enable large-scale, cost competitive production of the next generation of electric-drive vehicles.
Argonne has discovered many classes of the SEI additives based on the empirical
selection rule and the quantum chemical calculations. Electrochemical properties of new SEI additives were thoroughly investigated in graphite
based lithium ion batteries. SEI formation were fully characterized by electrochemical method and FT-IR, Raman,
XPS instrumental measurements. The lithium ion cells containing ANL-SEI -1, ANL-SEI-2 and ANL-SEI-3 showed no or less impedance growth after cycling and excellent capacity retention even at elevated temperature (55oC).
Novel SEI additive based on cyclic phosphate compounds were designed and synthesized. Initial electrochemical study has shown promising results. We will continue to explore this additive and its derivatives in FY13.
Summary
25
Technical Back-Up Slides
Power Evaluation of ANL-SEI-1: HPPC Data
26
0 20 40 60 80 1000
50
100
150
200
250
ASI
, ohm
*cm
2
DOD %
ASI discharge Gen 2 electrolyte ASI charge Gen 2 electrolyte ASI discharge 0.2 w% OBD ASI charge 0.2 w% OBD
0
50
100
150
200
250
300
0 10 20 30 40 50 60 70 80 90 100
AS
I, o
hm
*cm
2
DOD, %
ASI-Disc
ASI-Chrg
OO O O
O
O
27
In MCMB/Li half cell, additive reduction occurs at 1.6V, prior to the SOA SEI formation at a potential between 0.6~0.8V vs Li+/Li. The peak intensity is proportional to the concentration of the additive.
0.0 0.5 1.0 1.5 2.0-1.2
-1.0
-0.8
-0.6
-0.4
-0.2
0.0
1.2 M LiPF6
1.2 M LiPF6 + 0.5% LiDFOB 1.0 M LiDFOB
dQ/d
V, m
Ah/V
Cell potential, V
New SEI Traditional SEI
NMC/MCMB Cell MCMB/Li Cell
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.20.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0% LiDFOB 0.5% LiDFOB 2% LiDFOB 3% LiDFOB 5% LiDFOB
dQ/d
V, m
Ah/V
Cell voltage, V
New SEI
28
Li/MCMB
0 20 40 60 80 100
0
1
2
3
4
Pristine 1% LTFOP 2% LTFOP 3% LTFOP
Capa
city
, mAh
Aging Time, days
Li/MCMB
PF
F
F
O
O
O
O
F
Li
LTFOP improves the calendar life of both MCMB anode at high temperature.
With addition of 1% LTFOP, the onset thermal decomposition temperature of SEI was pushed above 175oC (70oC increase compared with the conventional SEI).
100 200 300 4000
5
10
50 100 150 200 2500.0
0.5
1.0
Heat
Flo
w, W
/g
Temperature, oC
Heat
Flo
w, W
/gTemperature, oC
Pristine 1 wt% LTFOP
5°C/min scan rate