ADVANCED CONSTRUCTION TECHNOLOGY SERVICES-QATAR · ADVANCED CONSTRUCTION TECHNOLOGY SERVICES-QATAR . GATE 172, STREET 13 . INDUSTRIAL AREA, PO BOX NO 22159 . DOHA, QATAR . Testing

This is to attest that

ADVANCED CONSTRUCTION TECHNOLOGY SERVICES-QATAR GATE 172, STREET 13

INDUSTRIAL AREA, PO BOX NO 22159 DOHA, QATAR

Testing Laboratory TL-558

has met the requirements of AC89, IAS Accreditation Criteria for Testing Laboratories, and has demonstrated compliance with ISO/IEC Standard 17025:2017, General requirements for the competence of testing and calibration laboratories. This organization is accredited to provide the services specified in the scope of accreditation maintained on the IAS website (www.iasonline.org).

This certificate is valid up to May 1, 2022.

This accreditation certificate supersedes any IAS accreditation bearing an earlier effective date. The certificate becomes invalid upon suspension, cancellation or revocation of accreditation. See www.iasonline.org for current accreditation information, or contact IAS at 562-364-8201.

Raj Nathan President

http://www.iasonline.org/




International Accreditation Service, Inc.

3060 Saturn Street, Suite 100, Brea, California 92821 U.S.A. Telephone +1 562-364-8201 — [email protected]

www.iasonline.org Page 1 of 38

IAS Accreditation Number TL-558 Company Name Advanced Construction Technology Services - Qatar Address Gate 172, Street 13, Industrial Area, PO Box No 22159

Doha, State of Qatar Contact Name Shohel Rana, QHSE Manager Telephone +974 44601257 Effective Date of Scope December 26, 2019 Accreditation Standard ISO/IEC 17025: 2017

S.N PWA

No. Category Standard/ Method No. /Date

Standard/Method Title & Section

Location / Facility Authorized Technicians

1 2.16 Aggregate AASHTO T304 Uncompacted Void Content of Fine Aggregate

Street 13/ Aggregate

1. Harison Kwasi 2. Jude Niroshan 3. Hari Sasidharan 4. Bhabi Lal Kapli 5. Prakash Karki

2 2.09 Aggregate ASTM C40-2019 Standard Test Method for Organic Impurities in Fine Aggregates for Concrete


1. Jonalyn Ella 2. Rifan Ahmed

3 2.13 Aggregate ASTM C88-2018 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate


1. Hari Sasidharan 2. Harison Aniwe 3. Jude Niroshan 4. Prakash Karki 5. Nikesh Mundayat 6. Harrison Kwasi

4 2.04 Aggregate ASTM C117-2017, Procedure A

Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing1


1. Hari Sasidharan 2. Harison Aniwe 3. Jude Niroshan 4. Prakash Karki 5. Shandra 6. Harrison Kwasi

http://www.ilac.org/



mailto:[email protected]







TL-558 Page 2 of 38 Advanced Construction Technology Services - Qatar

S.N PWA No. Category Standard/

Method No. /Date Standard/Method Title &

Section Location /

Facility Authorized Technicians

5 2.08 Aggregate ASTM C123-2014 Lightweight Particles in Aggregate


1. Hari Sasidharan 2. Harison Aniwe 3. Jude Niroshan 4. Nikesh Mundayat 5. Harrison Kwasi

6 2.06 Aggregate ASTM C127-2015 Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate


1. Hari Sasidharan 2. Harison Aniwe 3. Jude Niroshan 4. Nikesh Mundayat

7 2.05 Aggregate ASTM C128-2015 Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate



8 2.11 Aggregate ASTM C131-2014 Standard Test Method for Resistance to Degradation of Small- Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine


1. Harison Aniwe 2. Jude Niroshan 3. Nikesh Mundayat

9 2.03 Aggregate ASTM C136-2014 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates


1. Harison Aniwe

10 2.07 Aggregate ASTM C142-2017 Standard Test Method for Clay Lumps and Friable Particles in Aggregates


1. Hari Sasidharan 2. Harison Aniwe 3. Prakash Karki

11 2.12 Aggregate ASTM C535-2016 Standard Test Method for Resistance to Degradation of Large- Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine1


1. Hari Sasidharan 2. Harison Aniwe 3. Jude Niroshan 4. Prakash Karki

12 2.02 Aggregate ASTM C702-2018 Standard Practice for Reducing Samples of Aggregate to Testing Size

Site/ Street 13/ Aggregate

1. Hari Sasidharan 2. Harison Aniwe 3. Nikesh Mundayat 4. Prakash Karki

13 2.10 Aggregate ASTM D4791-2010, Method A

Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate






Section Location /


14 2.15 Aggregate ASTM D546-2017 Sieve analysis of Mineral filler Street 13/ Aggregate


15 2.14 Aggregate ASTM D5821-2017 Determining the Percentage of Fractured Particles in Coarse Aggregate



16 2.33 Aggregate BS 812-110:1990 Determination of aggregate crushing value



17 2.34 Aggregate BS 812-111:1990 Determination of ten percent fines value



18 2.35 Aggregate BS 812-112:1990 Determination of aggregate impact value


1. Nikesh Mundayat 2. Harison Aniwe 3. Jude Niroshan 4. Hari Sasidharan

19 2.26 2.27 2.23

Aggregate BS EN 933-1:2012 Tests for geometrical properties of aggregates. Determination of particle size distribution. Sieving method



20 2.29 Aggregate BS EN 933-3:2012 Tests for geometrical properties of aggregates. Determination of particle shape. Flakiness index


1. Hari Sasidharan 2. Harrison Aniwe 3. Jude Niroshan 4. Nikesh Mundayat

21 2.28 Aggregate BS EN 933-7:1998 Determination of Shell Content


1. Harison Aniwe 2. Jude Niroshan 3. Hari Sasidharan 4. Nikesh Mundayat 5. Prakash Karki

22 2.19 Aggregate BS EN 1097-6:2013

Determination of Particle density and water absorption


1. Harison Aniwe 2. Jude Niroshan 3. Hari Sasidharan 4. Nikesh Sasidharan 5. Prakash Karki




Section Location /


23 2.37 Aggregate BS EN 1744-1:2009 +A1:2012 C7

Tests for chemical properties of aggregates; Clause7 Determination of water soluble chloride salts using the Volhard Method

Street 13/ Chemistry

1. Jonalyn Ella 2. M M Aasik 3. Rifan Ahmed


Tests For Chemical Properties of Aggregates; Clause10 Determination of Water Soluble Sulphates




Acid-soluble Sulfate in Aggregates



26 2.36 Aggregate BS EN 1744-5:2006

Acid-soluble Chloride in Aggregates


1. Jonalyn Ella 2. Rifan Ahmed 3. MM Aasik

27 NA Air Monitoring Inhouse Method Air Monitoring Using Lebellium Instrument

Environmental 1. Hussein Ibrahim

28 NA Air Monitoring In-house method Carbon Dioxide (CO2) Environmental 1. Hussein Ibrahim 29 NA Air Monitoring In-house method Carbon Monoxide (CO) Environmental 1. Hussein Ibrahim 30 NA Air Monitoring In-house method Hydrogen Sulfide (H2S) Environmental 1. Hussein Ibrahim 31 NA Air Monitoring In-house method Methane Environmental 1. Hussein Ibrahim 32 NA Air Monitoring In-house method Noise Environmental 1. Hussein Ibrahim 33 NA Air Monitoring In-house method PID (VOC) Environmental 1. Hussein Ibrahim 34 5.10 Cementitious

Materials ASTM C114-2018 Standard Test Methods For

Chemical Analysis for hydraulic Cement. Sec. 18. Loss On Ignition.


1. Jonalyn Ella 2. Md. Erphan* 3. MM Aasik 4. Rifan Ahmed

35 5.02 Cementitious Materials

ASTM C183-2016 Method of sampling of cement

Site/ Cement 1. Allan Abinguna 2. Sandip Damai


ASTM C187-2016 Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

Street 14/ Cement

1. Allan Abinguna 2. Sandip Damai


ASTM C191-2019 Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle

Street 14/ Cement





Section Location /



ASTM C311-2018 C11 & C12

Standard Test Methods For Sampling And Testing Fly ash of Natural Pozzolans For Use In Portland Cement Concrete/ Moisture Content


1. Md. Erphan 2. Rifan Ahmed 3. MM Aasik


ASTM C311-2018 C13 & C14

Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete / Loss on Ignition




ASTM C349-2018 Standard Test Method for Compressive Strength of Hydraulic- Cement Mortars (Using Portions of Prisms Broken in Flexure)

Street 14/ Cement


41 NA Cementitious Materials

ASTM C359-2018 Early stiffening of Portland cement

Street 14/ Cement



ASTM C939-2016a Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method)

Street 14/ Grout



ASTM C940-2016 Standard Test Method for Expansion and Bleeding of Freshly Mixed Grouts for Preplaced-Aggregate Concrete in the Laboratory

Street 14/ Grout



ASTM C1012-2018b Length change of cement mortars

Street 14/ Cement



ASTM C1064-2017 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

Site/ Concrete 1. Sangheetan Sekeran 2. Sujith Surendran 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut


ASTM C1240-2015 Standard Specification for Silica Fume Used in Cementitious Mixtures/ Moisture content and Loss on Ignition.






Section Location /



ASTM C1240-2015 C11

Moisture and Loss on Ignition of Microsilica


1. Jonalyn Ella 2. Md. Erphan 3. MM Aasik 4. Rifan Ahmed


ASTM C1240-2015 C16

CL 16. Accelerated Pozzolanic Strength Activity Index with Portland Cement

Street 14/ Cement



BS EN 196-1:2016 Methods of testing cement. Determination of Strength

Street 14/ Cement



BS EN 196-2:2013, C4.5.5 to 4.5.6

Chemical Analysis of cement (SiO2)


1. Jonalyn Ella 2. Md. Erphan 3. MM Aasik 4. Rifan Ahmed


BS EN 196-2:2013 C4.5.10

Chemical Analysis of cement (Fe2O3)


1. Md. Erphan


BS EN 196-2:2013 C4.5.11

Chemical Analysis of cement (Al2O3)


1. Md. Erphan


BS EN 196-2:2013 C4.5.14

Chemical Analysis of cement (CaO)


1. Md. Erphan 2. Jonalyn Ella


BS EN 196-2:2013 C4.5.15

Chemical Analysis of cement (MgO)


1. Md. Erphan 2. Jonalyn Ella


BS EN 196-2:2013 C4.5.16

Chemical Analysis of cement (Cl)


1. Md. Erphan


BS EN 196-2:2013 C4.5.19

Chemical Analysis of cement (Alkalis)


1. Md. Erphan


BS EN 196-2:2013 C7

Method of testing cement-Part 2 Chemical analysis of cement; Determination of loss on ignition


1. Jonalyn Ella 2. Md Erphan* 3. MM Aasik 4. Rifan Ahmed


BS EN 196-2:2013 C8

Method of testing cement-Part 2 Chemical analysis of cement; Clause 8 Determination of sulphate.


1. Jonalyn Ella 2. Md. Erphan* 3. MM Aasik 4. Rifan Ahmed


BS EN 196-3:2016 Determination of setting time of cement

Street 14/ Cement



BS EN 196-3:2016 Standard Test Methods of testing cement. Determination of setting times and soundness

Street 14/ Cement





Section Location /



BS EN 196-5:2011 Pozzolanicity Test of Pozzolanic Cement


1. Md. Erphan 2. MM Aasik


BS EN 196-6:2018 C4

Fineness by Blaine Air- Permeability Apparatus




BS EN 196-7:2007 Taking & preparing samples of cement

Street 14/ Cement



BS EN 480-8:2012 Determination of the conventional dry material content in Admixtures


1. Jonalyn Ella 2. MM Aasik 3. Rifan Ahmed

65 3.01 Concrete ASTM C31-2019 Making and curing of concrete tests specimen

Site/ Street 14/ Concrete

1. Sangheetan Sekeran 2. Ismail Seeni Lebbe 3. Sujanthan Arumugam 4. Rareesh Gopalapllah 5. Sujith Surendran 6. Prafulla Kasajo 7. Gokarna Raut

66 3.05 Concrete ASTM C39-2018 Compressive strength of concrete cylindrical specimen


1. Allan Abinguna 2. Mahendra Singh 3. Richard Ohene

67 3.08 Concrete ASTM C42-2018a Obtaining and testing of drilled cores and sawed beams


1. Sujith Surenderan 2. Sangheetan Sekeran 3. Ismail Seeni Lebbe 4. Sujanthan Arumugam 5. Rareesh Gopalapllah 6. Prafulla Kasajo 7. Gokarna Raut

68 5.5 Concrete ASTM C109-2016 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50- mm] Cube Specimens)


1. Allan Abinguna 2. Daniel Nutassey 3. Sandip Dimai

69 3.14 Concrete ASTM C138-2017a Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

Street 14/ Concrete

1. Sangeethan Sekeran 2. Sujith Surenderan 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut




Section Location /


70 3.04 Concrete ASTM C143-2015a Slump Test Site/ Street 14/ Concrete


71 3.02 Concrete ASTM C172-2017 Sampling of fresh concrete Site/ Street 14/ Concrete


72 3.13 Concrete ASTM C173-2016 Air content test for fresh concrete by volumetric method



73 3.12 Concrete ASTM C231-2017a Air content test for fresh concrete by pressure method, Type B



74 3.06 Concrete ASTM C617-2015 Capping of cylindrical concrete specimen (Sulfur Mortar - 6.2.4)

Street 14/ Concrete


75 5.23 Concrete ASTM C989-2018a Slag Cement for Use in Concrete and Mortars

Street 14/ Concrete

1. Allan Abinguna 2. Daniel Nutassey 3. Sandip Dimai

76 3.11 Concrete ASTM C1202-2019 Standard Test Method for Electrical Indication of Concrete's Ability to Resist Chloride Ion Penetration

Street 14/ Concrete

1. Allan Abinguna 2. Daniel Nutassey 3. Dinesh Sah 4. Rumaizan




Section Location /


77 3.07 Concrete ASTM C1231-2015 Testing concrete cylinders using unboned caps

Street 14/ Concrete


78 3.15 Concrete ASTM C1385-2017 Standard Practice for Sampling Materials for Shotcrete

Street 14/ Concrete


79 3.19 Concrete ASTM C1611-2018 Slump flow test for self- consolidated concrete

Street 14/ Concrete

1. Sujith Surenderan 2. Sangheetan Sekeran 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut

80 3.20 Concrete ASTM C1621-2017 Passing Ability for Self- Consolidating Concrete by J-Ring

Street 14/ Concrete

1. Sujith Surenderan 2. Sangheetan Sekeran 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut

81 3.17 Concrete ASTM C1688-2014a Density Determination of Pervious Concrete


1. Sujith Sudarsan 2. Rarish Gopala 3. Sujanthan Arumugam 4. Sangheetan Sekeran

82 3.18 Concrete ASTM C1701-2017a Infiltration Test for In place Pervious Concrete


1. Sujith Sudarsan 2. Rarish Gopala 3. Sujanthan Arumugam 4. Sangheetan Sekeran

83 3.30 Concrete BS 1881-122:2011 Testing concrete. Method for determination of water absorption

Street 14/ Concrete

1. Allan Abinguna 2. Dinesh Sah 3. Daniel Kwaku 4. Rumaizan

84 3.33 Concrete BS 1881-124:2015 C10.2

Testing concrete. Methods for analysis of hardened concrete/Acid soluble chloride in concrete


1. Jonalyn Ella 2. Rifan Ahmed 3. Md. Erphan 4. Raju Bhendheni




Section Location /


85 3.34 Concrete BS 1881-124:2015 C10.3

Testing concrete. Methods for analysis of hardened concrete/Acid soluble sulphate in concrete


1. Jonalyn Ella 2. Rifan Ahmed 3. Md. Erphan 4. Raju Bhendheni

86 3.31 Concrete BS 1881-208:1996 Testing concrete. Recommendations for the determination of the initial surface absorption of concrete

Street 14/ Concrete

1. Allan Abinguna 2. Denish Sah 3. Daniel Kwaku 4. Rumaizan

87 3.21 Concrete BS EN 12350-1:2019

Testing fresh concrete. Sampling


1. Sangheetan Sekeran 2. Sujith Surenderan 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut

88 3.23 Concrete BS EN 12350-2:2019

Testing fresh concrete. Slump- test



89 3.24 Concrete BS EN 12350-5:2019

Flow table test Street 14/ Concrete


90 3.35 Concrete BS EN 12350-9:2010

Testing Fresh Concrete, Part 9: Self Compacting Concrete - V- funnel Test

Street 14/ Concrete

1. Sangeethan Sekeran 2. Sujith Surenderan 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. smail Seeni Lebbe 6. Sujanthan Arumugam 7. Gokarna Raut




Section Location /


91 3.36 Concrete BS EN 12350-10:2010

Testing Fresh Concrete, Part 10: Self Compacting Concrete - L Box Test

Street 14/ Concrete


92 3.22 Concrete BS EN 12390-2:2019

Testing hardened concrete. Making and curing specimens for strength tests



93 3.26 Concrete BS EN 12390-3:2019

Testing hardened concrete. Compressive strength of test specimens


1. Allan Abinguna 2. Mahendra Singh 3. Richard Ohene 4. Hari Nere

94 3.27 Concrete BS EN 12390-7:2019

Density of hardened concrete Site/ Street 14/ Concrete

1. Allan Abinguna 2. Denish Sah 3. Daniel Kwaku 4. Rumaizan

95 3.29 Concrete BS EN 12390-8:2019

Testing hardened concrete. Depth of penetration of water under pressure

Street 14/ Concrete


96 3.28 Concrete BS EN 12504-1:2009

Testing concrete in structures. Cored specimens. Taking, examining and testing in compression

Street 14/ Concrete

1. Sujith Surenderan 2. Sangheetan Sekeran 3. Rareesh Gopalapillai 4. Prafulla Kasaju 5. Ismail Seeni Lebbe 6. Sujantham Arumugam 7. Gokarna Raut 8. Allan Abinguna 9. Richard Ohene 10. Mahendra Singh

97 NA Concrete DIN 1048-1979 Water penetration test Street 14/ Concrete





Section Location /


98 3.32 Concrete NT Build 492:1999 Chloride penetration test Street 14/ Concrete

1. Allan Abinguna 2. Rumaizan Kamalde 3. Daniel Kwaku 4. Dinesh Sah

99 NA Concrete Rilem CPC 11.3:1994

Total porosity Street 14/ Concrete

1. Allan Abinguna 2. Daniel Kwaku 3. Dinesh Sah 4. Rumaizan

100 NA Dimention Stone

ASTM C1354-2015 Strength of Individual Stone Anchorages in Dimension stone

Street 14/ Concrete

1. Richard Ohene 2. Najath 3. Allan Abinguna

101 N/A Emulsified Asphalt

ASTM D7496-2018 Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer

Street 13/ Asphalt

1. Hari Sasidharan 2. Bhabi Lal 3. Chandra Narayanan 4. Abdul Rahman

102 9.72 Environmental APHA 3500-Cr B, 22nd Edition 2012

Chromium (VI) Street 13/ Chemistry

1. M M Aasik 2. Jona Ella 3. Raju B

103 9.33 Environmental APHA/AWWA 4500-P D&C 22nd Edition 2012

Phosphorous (total) Street 13/ Chemistry

1. Jona A 2. Raju B

104 9.82 Environmental APHA/AWWA/ 4500-SiIO2-C, 22nd Edition 2012

Total Silicates Street 13/ Chemistry

1. Jona Ella 2. Raju B

105 9.88 Environmental APHA/AWWA-9223B 22nd Edition2012 IDEXX method

Fecal Coliform Street 13/ Chemistry

1. MM Aasik 2. Jonalyn Ella

106 9.91 Environmental IDEXX Pseudomonas aeruginosa Street 13/ Chemistry

1. MM Aasik

107 NA Environmental SMWW 22nd. Ed. 2310 B

Acidity by Titratione Method Street 13/ Chemistry

1. Jonalyn Ella

108 9.03 Environmental SMWW 22nd. Ed. 2130 B

Turbidity Street 13/ Chemistry

1. Jonalyn Ella 2. MM Aasik 3. Raju B 4. George Thumbi


Bicarbonate by Titration method


1. Jonalyn Ella 2. George Thumbi 3. MM Aasik




Section Location /



Carbonate by Titration method




P-Alkalinity by Titration method




Total Alkalinity by Titration method



113 9.39 Environmental SMWW 22nd. Ed. 2340 C

Total Hardness Street 13/ Chemistry

1. Jonalyn Ella


Conductivity Street 13/ Chemistry

1. Jonalyn Ella 2. MM Aasik 3. Raju Bhendheni 4. George Thumbi

115 NA Environmental SMWW 22nd. Ed. 2520 B

Salinity by Conductivity Method


1. Jonalyn Ella 2. Raju Bhendheni


Total Solids Street 13/ Chemistry



Total Dissolved Solids Street 13/ Chemistry



Total Volatile Dissolved Solids Street 13/ Chemistry

1. Jonalyn Ella

119 9.05 Environmental SMWW 22nd. Ed. 2540 D

Total Suspended Solids Street 13/ Chemistry

1. Jonalyn Ella 2. Raju Bhendheni 3. George Thumbi


Total Volatile Suspended Solids


1. Jonalyn Ella

121 9.09 Environmental SMWW 22nd. Ed. 2540 F

Settleable Solids Street 13/ Chemistry

1. Jonalyn Ella 2. MM Aasik 3. George Thumbi

122 NA Environmental SMWW 22nd. Ed. 2550

Temperature Street 13/ Chemistry

1. George Thumbi 2. Rifan Ahmed 3. Jonalyn Ella 4. Raju Bhendheni




Section Location /


123 9.47 Environmental SMWW 22nd. Ed. 3120 / USEPA 6010C, Metals by Plasma Emission

Aluminum Street 13/ Chemistry

1. MD Erphan


Antimony Street 13/ Chemistry

1. MD Erphan 2. Jonalyn Ella


Arsenic Street 13/ Chemistry

1. MD Erphan


Barium Street 13/ Chemistry

1. MD Erphan


Beryllium Street 13/ Chemistry

1. MD Erphan


Boron Street 13/ Chemistry

1. MD Erphan


Cadmium Street 13/ Chemistry

1. MD Erphan


Calcium Street 13/ Chemistry

1. MD Erphan




Section Location /



Chromium Street 13/ Chemistry

1. MD Erphan


Cobalt Street 13/ Chemistry

1. MD Erphan


Copper Street 13/ Chemistry

1. MD Erphan


Iron Street 13/ Chemistry

1. MD Erphan


Lead Street 13/ Chemistry

1. MD Erphan


Lithium Street 13/ Chemistry

1. MD Erphan


Magnesium Street 13/ Chemistry

1. MD Erphan


Manganese Street 13/ Chemistry

1. MD Erphan




Section Location /



Mercury Street 13/ Chemistry

1. MD Erphan


Molybdenum Street 13/ Chemistry

1. MD Erphan


Nickel Street 13/ Chemistry

1. MD Erphan


Phosphorous Street 13/ Chemistry

1. MD Erphan


Potassium Street 13/ Chemistry

1. MD Erphan


Selenium Street 13/ Chemistry

1. MD Erphan


Silicon Street 13/ Chemistry

1. MD Erphan


Silver Street 13/ Chemistry

1. MD Erphan




Section Location /



Sodium Street 13/ Chemistry

1. MD Erphan


Thallium (TI) Street 13/ Chemistry

1. MD Erphan


Vanadium Street 13/ Chemistry

1. MD Erphan


Zinc Street 13/ Chemistry

1. MD Erphan

151 9.71 Environmental SMWW 22nd ed. 3120 B / USEPA 6010C

Tin by ICP-AES Method Street 13/ Chemistry

1. MD Erphan

152 9.66 Environmental SMWW 22nd ed. 3120 B / USEPA 6010C

Titanium by ICP-AES Method CHEMISTRY 1. MD Erphan

153 9.40 Environmental SMWW 22nd. Ed. 3500-Ca B & 3500-Mg B

Calcium by Hardness & Magnesium by Calculation


1. Jonalyn Ella

154 9.41 Environmental SMWW 22nd. Ed. 3500-Mg B

Magnesium by Calculation Street 13/ Chemistry

1. Jonalyn Ella

155 9.25 Environmental SMWW 22nd. Ed. 4500-B

Chloride Street 13/ Chemistry

1. Jonalyn Ella 2. Raju Bhendheni 3. MM Aasik

156 9.24 Environmental SMWW 22nd. Ed. 4500-Cl¯ B

Residual Chlorine Street 13/ Chemistry

1. Jonalyn Ella 2. George Thumbi

157 9.23 Environmental SMWW 22nd. Ed. 4500-Cl G

Total Chlorine Street 13/ Chemistry

1. Jonalyn Ella 2. George Thumbi




Section Location /


158 9.01 Environmental SMWW 22nd. Ed. 4500-H⁺ B

pH Street 13/ Chemistry

1. Jonalyn Ella 2. MM Aasik 3. Raju Bhendheni 4. George Thumbi

159 9.21 Environmental SMWW 22nd ed. 4500-NO₂⁻ B

Nitrite Nitrogen by Colorimetric Method


1. Jonalyn Ella 2. MM Aasik

160 9.20 Environmental SMWW 22nd. Ed. 4500-NO₃¯ D

Nitrogen Nitrate Street 13/ Chemistry

1. Jonalyn Ella

161 9.37 Environmental SMWW 22nd. Ed. 4500-S²¯ F

Sulphide Street 13/ Chemistry

1. Jonalyn Ella 2. MM Aasik 3. Raju Bhendheni

162 9.36 Environmental SMWW 22nd. Ed. 4500-SO₄²¯ C

Sulphate Street 13/ Chemistry


163 9.13 Environmental SMWW 22nd. Ed. 5210 B/ 4500-O C or G

Biochemical Oxygen Demand (BOD)


1. Jonalyn Ella


Oil & Grease Street 13/ Chemistry

1. Jonalyn Ella


Chemical Oxygen Demand (COD)


1. Jonalyn Ella

166 9.79 Environmental SMWW 22nd ed. 5310 B / USEPA 9060

Total Organic Carbon (TOC) by High Temperature Combustion Method


1. Jonalyn Ella

167 NA Environmental SMWW 22nd ed. 9221

E.coli by Multiple Tube Fermentation Technique


1. MM AAsik 2. Jonalyn Ella


E. coli by Enzyme Substrate Method




Total Coliform by Enzyme Substrate Method



170 9.81 Environmental USEPA 8260C/5021A

Volatile Organic Compounds (VOCs) BTEX


1. Jonalyn Ella

171 NA Environmental USEPA 8270D Semi-volatile Organic Compounds (SVOC) by GC/MS


1. Jonalyn Ella

172 NA Geotechnical AASHTO T256/ ASTM D4695-2015

General Pavement Deflection Measurements

Site/ Geo 1. Janamjeet Singh 2. Kameshwar Kamati 3. Mogan Chettier

173 NA Geotechnical ASTM D3967-2016 Splitting Tensile Strength of Rock Core Specimen

Sailiya/ Rock 1. Antony Kabugi 2. Maxwel Okoth




Section Location /


174 8.04 Geotechnical ASTM D4543-2019 Standard Practices for Preparing Rock Core as Cylindrical Test Specimens and Verifying Conformance to Dimensional and Shape Tolerances

Street 25/ Rock

1. Antony Kabugi 2. Maxwel Okoth

175 NA Geotechnical ASTM D4644-2016 Slake Durability of Rock Specimens


176 NA Geotechnical ASTM D4694-2015 Standard Test Method for Deflections with a falling weight type impulse load device. FWD/HWD Testing

Site/ Geo 1. Janamjeet Singh 2. Vladimir Viray 3. Mogan Chettier

177 10.11 Geotechnical ASTM D4945-2017 Standard Test Method for High- Strain Dynamic Testing of Deep Foundations

Site/ Geo 1. Janamjeet Singh 2. Vladimir Viray

178 8.03 Geotechnical ASTM D5731-2016 Standard Test Method for Determination of the Point Load Strength Index of Rock and Application to Rock Strength Classifications


179 10.9 Geotechnical ASTM D5882-2016 Standard Test Method for Low Strain Impact Integrity Testing of Deep Foundations


180 10.10 Geotechnical ASTM D6760-2016 Standard Test Method for Integrity Testing of Concrete Deep Foundations by Ultrasonic Cross hole Testing


181 8.23 Geotechnical ASTM D6951-2018 Dynamic Cone Penetrometer for Shallow Pavements, DCPT

Site/ Geo 1. Kameshwar Kamati 2. Jasheel Mushabdeen

182 8.05 Geotechnical ASTM D7012-2014 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures


183 NA Geotechnical ASTM D7625-2010 Abrasiveness of Rock Using CERCHAR Method


184 8.20 Geotechnical ASTM G57-2012 Soil Resistivity Site/ Geo 1. Dilin Das




Section Location /


185 8.08 Geotechnical BS 1377-7:1990 Sec. 4

Methods of Test for Soils for Civil Engineering Purposes. Shear Strength Tests (Total Stress), Direct Shear of Soil (Small Box)

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan

186 8.19 Geotechnical BS 1377-9:1990 C3.3

Methods for test for soils for civil engineering purposes. In-situ tests (SPT)

Site/ Geo 1. All Geologists 2. All Drillers

187 8.21 Geotechnical BS 1377-9:1990 C4.1

Methods for Test for Soils For Civil Engineering Purposes. In- situ Tests (Plate Load Test)

Site/ Soil Street-13

1. Jude Niroshan 2. Jayson Enrile

188 8.22 Geotechnical BS 1377-9:1990 Sec. 4.3

Methods for test for soils for civil engineering purposes. In-situ tests, Field CBR

Site/ Geo 1. Kameshwar Kamati 2. Jasheel Mushabdeen

189 8.14 Geotechnical BS 5930:2015; Section 3 C22

Code of practice for site investigations. Soil Sampling

Site/ Geo 1. All Geologists

190 8.15 Geotechnical BS 5930:2015 Section 3 C23.3

Code of practice for site investigations. Groundwater sampling

Site/ Geo 1. Kameshwar Kamuti

191 8.17 Geotechnical BS 5930:2015 Section 4 C25

Code of practice for site investigations. Falling Head Permeability Test


192 8.18 Geotechnical BS 5930:2015 Section 4 C25.5

Code of practice for site investigations. Packer Test


193 8.16 Geotechnical BS 5930:2015 Section 6 C27, C47

Code of Practice for Site Investigations, Ground Water Level Measurement

Site/ Geo 1. All Geologists 2. All Drillers 3. Kameshwar Kamati

194 NA Geotechnical EN 13036-7:2003 Road and Airfield Surface Characteristics - Test Methods - Part 7: Irregularity measurement of pavement courses - The straightedge test

Site/ Geo 1. Janamjeet Singh 2. Kameshwar Kamati

195 NA Geotechnical ISRM Suggested Method, part 1.3

Porosity/Density Determination Using Saturation and Buoyancy Techniques





Section Location /


196 11.16 Geotextiles & Water Proofing

ASTM D412-2016 Vulcanized Rubber and Thermoplastic Elastomers—Tension

Street 14/ Geotextiles

1. Mahendra Sing Budhathoki 2. Daniel Kwaku Nutassey 3. Allan Abinguna


ASTM D570-2018 Water Absorption of Plastics Street 14/ Geotextiles

1. Allan Abinguna 2. Mahendra Singh 3. Richard Ohene 4. Daniel Kwaku


ASTM D638-2014 Tensile Properties of Plastics Street 14/ Geotextiles



ASTM D751-2019 Puncture resistance - Coated Fabrics




ASTM D1000-2017 Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications




ASTM D1004-2013 Tear Resistance (Graves Tear) of Plastic Film and Sheeting




ASTM D3767-2014 Dimensions Measurement of Rubber




ASTM D3787-2016 Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test




ASTM D4533-2015 Trapezoid Tearing Strength of Geotextiles






Section Location /



ASTM D5034-2017 Breaking Strength and Elongation of Textile Fabrics (Grab Strength)




ASTM D5035-2019 Breaking Force and Elongation of Textile Fabrics (Strip Method)




ASTM D5199-2019 Measuring The Nominal Thickness Of Geosynthetics


1. Mahendra Singh 2. Allan Abinguna


ASTM E96-2016 Water Vapor Transmission Rate


1. Hari Sasidharan 2. Harrison Kwasi 3. Abdul Rehman 4. Prakash Karki


ASTM E154-2019 Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover




BS EN ISO 527-3:2018

Plastics —Determination of tensile properties — Part 3: Test conditions for films and sheets




BS EN 1849-1:2000

Determination of thickness and mass per unit area of Bitumen sheets




BS EN 1849-2:2019

Determination of thickness and mass per unit area of Plastic and rubber sheets




BS EN ISO 5084-1997

Determination Of Thickness Of Textiles




BS EN ISO 10319-2015

Geosynthetics — Wide-width tensile test






Section Location /



BS EN ISO 11058-2010

Geotextiles and geotextile-related products —Determination of water permeability characteristics normal to the plane, without load




BS EN 12127-1998 Determination Of Mass Per Unit Area (Weight)


1. Mahendra Singh 2. Richard Ohene 3. Daniel Kwaku 4. Allan Abinguna


BS EN ISO 12236-2006

Static Puncture Test (CBR Test)


1. Allan Abinguna 2. Mahendra Singh Budhathoki


BS EN ISO 13433-2006

Geosynthetics —Dynamic perforation test (cone drop test)



219 NA Masonry Blocks and Paving

ASTM C97-2018 Standard Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone

Street 14/ Dimension Stone

1. Allan Abinguna 2. Richard Ohene 3. Mahendra Singh


ASTM C99-2018 Standard Test Method for Modulus of Rupture of Dimension Stone



221 4.15 Masonry Blocks and Paving

ASTM C140-2018a Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units

Street 14/ Masonry



ASTM C170-2017 Standard Test Method for Compressive Strength of Dimension Stone




ASTM C880-2018 Standard Test Method for Flexural Strength of Dimension Stone




ASTM C1353-2015a Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform, Double-Head Abraser


1. Allan Abinguna 2. Richard Ohene 3. Daniel Kwaku 4. Najath




Section Location /



BS EN 679:2005 Determination of the compressive strength of Autoclaved Aerated Concrete

Street 14/ Masonry



BS EN 771-1:2015 Specification for masonry units. Clay masonry units. Water absorption for interlocks

Street 14/ Blocks

1. Allan Abinguna 2. Richard Ohene 3. Najath


BS EN 771-3:2015 Specification for masonry units. Aggregate concrete masonry units (dense and lightweight aggregates)

Street 14/ Masonry



BS EN 772-1:2015 Methods of test for masonry units. Determination of compressive strength

Street 14/ Blocks



BS EN 772-2:1998, BS EN 771- 3:2015 (BS 6073-1:1981)

Precast concrete masonry units. Specification for precast concrete masonry units, Compressive Strength

Street 14/ Masonry

1. Allan Abinguna 2. Richard Ohene 3. Mahendra Singh 4. Najath


BS EN 772-11: 2011

Methods of test for masonry units. Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units.

Street 14/ Blocks

1. Allan Abinguna 2. Richard Ohene 3. Daniel Kwaku 4. Najath 5. Dinesh Sah


BS EN 772-16:2011

Methods of test for masonry units. Determination of dimensions

Street 14/ Masonry



BS 6717:2001 Annex B Superseded, Withdrawn BS EN 1338:2003

Measurement of dimensions of paving blocks

Street 14/ Blocks

1. Allan Abinguna 2. Daniel Nutassey 3. Richard Ohene




Section Location /



BS 6717:2001 Annex E Superseded, Withdrawn BS EN 1338:2003

Compressive strength of paving blocks

Street 14/ Blocks

1. Allan Abinguna 2. Daniel Nutassey 3. Richard Ohene 4. Mahendra Singh


BS EN 1338:2003 Annex E

Concrete paving blocks. Requirements and test methods, Water absorption for paving blocks

Street 14/ Blocks

1. Allan Abinguna 2. Daniel Nutassey 3. Richard Ohene 4. Mahendra Singh 5. Najath


BS EN 1338:2003 Annex F

Concrete paving blocks. Requirements and test methods, Tensile strength of paving blocks

Street 14/ Blocks




Concrete paving flags. Requirements and test methods, Water absorption for concrete paving flags/slabs

Street 14/ Concrete




Concrete paving flags. Requirements and test methods, Transverse strength of concrete paving slabs

Street 14/ Concrete



BS EN 1340:2003 Annex C

Concrete kerb units. Requirements and test methods, Measurement of dimensions of kerbs

Street 14/ Kerb Stone

1. Allan Abinguna 2. Richard Ohene 3. Daniel Nutassey



Concrete kerb units. Requirements and test methods, Water absorption for kerbs

Street 14/ Kerb Stone

1. Allan Abinguna 2. Richard Ohene 3. Mahendra Singh 4. Daniel Nutassey



Transverse stength of kerbs. Street 14/ Kerb Stone



BS EN 13748-1:2004+A1:2005 C5.5,5.8

Compressive strength and water absorption of terrazzo tiles

Street 14/ Tiles

1. Allan Abinguna 2. Richard Ohene 3. Najath 4. Mahendra Singh




Section Location /



ISRM CPC 11.3 Porosity of tiles Street 14/ Tiles


243 NA Mechanical ASTM A956-2017a ISO 16859-2015

Leeb hardness Street 14/ Consultancy

1. Mohamed Shahid 2. Asif Mahmood

244 NA Mechanical ASTM A1038-2017 Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method

Street 14/ Consultancy

1. Mohamed Shahid 2. Asif Mahmood

245 NA Mechanical ASTM F606-2016 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets


1. Mohamed Shahid 2. Asif Mahmood 3. Mahendra Sing 4. Allan Abinguna

246 NA Mechanical ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread



247 NA Mechanical ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 2: Nuts with specified property classes -- Coarse thread and fine pitch thread



248 10.04 Non Destructive ASTM C805-2018 Standard Test Method for Rebound Number of Hardened Concrete

Site/ NDT 1. Sujith Surendran 2. Sangeetan Sekeran 3. Ismail Seeni Lebbe 4. Sujanthan Arumugam 5. Rareesh Gopalapllah 6. Prafulla Kasajo 7. Gokarna Raut




Section Location /


249 10.13 Non Destructive ASTM D4541-2017 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers


250 10.15 Non Destructive ASTM D4787-2018/ ASTM D5162-2015

Holiday Detection of Coating Site/ NDT 1. Sujith Surendran 2. Sangeetan Sekeran 3. Ismail Seeni Lebbe 4. Sujanthan Arumugam 5. Rareesh Gopalapllah 6. Prafulla Kasajo 7. Gokarna Raut

251 10.14 Non Destructive ASTM D7091-2013 ASTM D6132-2017

Coating Thickness Measurement


252 NA Non Destructive ASTM E164 Ultrasonic Testing NDT 1. Mohamed Shahid 2. Abu Joseph

253 10.17 Non Destructive ASTM E165-2018/ ASME - Sec. V

Dye Penetration Test NDT 1. Nadir Ezzudeen 2. Abu Joseph

254 10.16 Non Destructive ASTM E709-2015/ ASME - Sec. V

Magnetic Particle Inspection NDT 1. Mohamed Shahid 2. Nadir Ezzudeen

255 10.02 Non Destructive ASTM E950-2018 ASTM E1926-2015

Road Surface Profiler Site/ Geotechni cal

1. Janamjeet Singh 2. Mogan Chettier

256 10.05 Non Destructive BS 1881-204:1988 Testing Concrete. Recommendations on the Use of Electromagnetic Cover Meters





Section Location /


257 10.06 Non Destructive BS EN 12504-4:2004

Testing Concrete. Determination Of Ultrasonic Pulse Velocity


258 10.07 Non Destructive Measurement of Crack Width & Monitoring on Site

Gauge Manual Method Site/ NDT 1. Sujith Surendran 2. Sangeetan Sekeran 3. Ismail Seeni Lebbe 4. Sujanthan Arumugam 5. Rareesh Gopalapllah 6. Prafulla Kasajo 7. Gokarna Raut

259 10.08 Non Destructive Measurement of Crack Width & Monitoring on Site

Microscope Manual Method Site/ NDT 1. Sujith Surendran 2. Sangeetan Sekeran 3. Ismail Seeni Lebbe 4. Sujanthan Arumugam 5. Rareesh Gopalapllah 6. Prafulla Kasajo 7. Gokarna Raut

260 13.03 Paints & Varnishes

ASTM D1212-2013 Measurement of Wet Film Thickness of Organic Coatings

Site 1. Sujith Sudarsan 2. Rarish Gopala Pillai 3. Sangeethan Sekeran 4. Rajjen 5. Chandra


ASTM D1212-2013 Measurement of Wet Film Thickness of Organic Coatings

Street 13/ Soil Lab

1. Hari Sasidharan 2. Harison Aniwe 3. Prakash Karki 4. Abdul Rahman 5. Chandra Narayanan


ASTM D1475-2013 Density of Liquid Coatings, Inks &paints

Street 13/ Soil Lab

1. Hari Sasidharanth 2. Harison Aniwe 3. Jude Niroshan 4. Prakash Karki 5. Abdul Rahman


ASTM D2196-2018e1

Rheological Properties of Non-Newtonian Materials by Rotational Viscometer

Street 13/ Soil Lab

1. Hari Sasidharan 2. Babi Lal 3. Chandra Narayanan 4. Abdul Rahman




Section Location /



ASTM D2369-2015 Determination of Volatile Content of Coatings


1. Rifan Ahmed 2. Erphan A


ASTM D3723-2017 Pigment Content of Water-Emulsion Paints by Low Temperature Ashing




ASTM D4541-2017 Adhesion (Pull off ) strength Site 1. Sujith Sudarsan 2. Rarish Gopala Pillai 3. Sangeethan Sekeran

267 NA Paints & Varnishes

BS EN ISO 4624-2016

Paints and varnishes — Pull-off test for adhesion exept Cl 6 &7

Site 1. Sujith Sudarsan 2. Rarish Gopala Pillai 3. Sangeethan Sekeran 4. Sujanthan Arumugam


BS EN ISO 787-9:2019

Determination of pH value of Aqueous suspension



269 6.05 Road and Pavement

ASTM D5-2019 Standard Test Method for Penetration of Bituminous Materials

Street 13/ Asphalt

1. Hari Sasidharan 2. Velautham Sachchutha 3. Hari Sasidharan 4. Bhabie Lal


ASTM D36-2014e1 Determination of softening point (ring and ball method)

Street 13/ Asphalt

1. Velautham Sachchutha 2. Hari Sasidharan 3. Bhabie Lal


ASTM D70-2018a Determination of Density of Bitumen

Street 13/ Asphalt

1. Bhabie Lal 2. Velautham Sachchutha 3. Hari Sasidharan


ASTM D92-2018 Standard Test Method for Flash and Fire Point by Cleveland Open Cup Tester

Street 13/ Asphalt

1. Hari Sasidharan 2. Bhabie Lal


ASTM D95-2018 Water in Petroleum Products and Bituminous Materials by Distillation

Street 13/ Asphalt

1. Hari Sasidharan 2. Abdul Rahman


ASTM D140-2016 Sampling Bituminous Materials

Site/ Asphalt 1. Hari Sasidharan 2. Harison Aniwe 3. Bhabi Lal


ASTM D402-2014 Distillation of Cutback Asphalt Street 13/ Asphalt

1. Hari Sasidharan 2. Wassim Feki 3. Abdul Rahman


ASTM D979-2017 Standard Practice for Sampling Bituminous Paving Mixtures

Site/ Asphalt 1. Hari Sasidharan 3. Harison Aniwe 4. Bhabi Lal




Section Location /



ASTM D2041-2019 Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures

Street 13/ Asphalt

1. Hari Sasidharan 2. Velautham Sachchutha 3. Bhabi Lal


ASTM D2042-2015 Solubility in trichloroethylene Street 13/ Asphalt

1. Velautham Sachchutha 2. Bhabi Lal 3. Hari Sasidharan


ASTM D2172-2017e1

Standard Test Methods for Quantitative Extraction of Bitumen From Bituminous Paving Mixtures

Street 13/ Asphalt

1. Hari Sasidharan 2. Bhabi Lal


ASTM D2726-2019 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures

Street 13/ Asphalt

1. Loreto Mingcal 2. Hari Sasidharan 3. Bhabi Lal


ASTM D2872-2019 Effect of heat and air on a moving film of asphalt (Rolling thin film oven test)

Street 13/ Asphalt



ASTM D2950-2014 Density of Bituminous Concrete in Place by Nuclear Methods

Site/ NDT 1. Alex Luna Santillan 2. Clark De Lara 3. Jonathan Hernandez 4. Jayson Enrile 5. Padam Bahadur Thapa 6. Ashwin Neupane 7. Allan Sampang 8. Roderick Galang 9. Stephen Gitau 10. Samuel Maina


ASTM D2995-2014 Application Rate of Bituminous Materials

Site/ Asphalt 1. Ramudesh K 2. Hari Sasidharan 3. Harison Aniwe 4. Bhabi Lal


ASTM D3549-2018 Method A

Standard Test Method for Thickness or Height of Compacted Bituminous Paving Mixture Specimens

Street 13/ Asphalt

1. Hari Sasidharan 2. Velautham Sachchutha 3. Bhabi Lal


ASTM D4402-2015 Viscosity Determination using Rotational Viscometer (RV)

Street 13/ Asphalt

1. Velautham Sachchutha 2. Hari Sasidharan 3. Bhabi Lal




Section Location /



ASTM D5361-2016 Standard Practice for Sampling Compacted Bituminous Mixtures for Laboratory Testing

Site/ Asphalt 1. Ramudesh K 2. Hari Sasidharan 3. Bhabi Lal


ASTM D5444-2015 Standard Test Method for Mechanical Size Analysis of Extracted Aggregate

Street 13/ Asphalt



ASTM D6307-2019 Asphalt content of hot mix asphalt by ignition method

Street 13/ Asphalt

1. Bhabi Lal 2. Velautham Sachchutha 3. Hari Sasidharan


ASTM D6521-2019 Accelerated aging of asphalt binder using PAV

Street 13/ Asphalt



ASTM D6648-2016 Flexural Creep Stiffness using the BBR

Street 13/ Asphalt

1. Lovek Mangesh 2. Hari Sasidharan 3. Velautham Sachchutha 4. Bhabi Lal


ASTM D6926-2016 Standard Practice for Preparation of Bituminous Specimens Using Marshall Apparatus

Street 13/ Asphalt

1. Velautham Sachchutha 2. Hari Sasidharan 3. Chandra Narayan 4. Bhabi Lal


ASTM D6931-2017 Indirect Tensile (IDT) Strength of Asphalt Mixtures

Street 13/ Soil Lab

1. Chandra Narayanan Shah 2. Abdul Rashid Rajon


ASTM D7173-2014 Separation Tendency of Polymers

Street 13/ Asphalt

1. Hari Sasidharan 2. Babi Lal 3. Chandra Narayanan 4. Abdul Rahman 5. Abdul Rashid


ASTM D7175-2015 Determining the Rheological Properties using DSR

Street 13/ Asphalt

1. Wassim Feki 2. Hari Sasidharan 3. Bhabi Lal


ASTM D7405-2015 AASHTO TP70

Multiple Creep and Recovery (MSCR), using Dynamic Shear Rheometer (DSR)

Street 13/ Asphalt

1. Wassim Feki 2. Hari Sasidharan 3. Bhabi Lal


ASTM E303-2018 Surface Frictional Propertiesusing the British Pendulum Tester

Street 13/ Asphalt

1. Hari Sasidharan 2. Ramudesh K 3. Jude Niroshan 4. Abdul Rahman 5. Bhabi Lal




Section Location /



BS 2000-58:2015 Softening Point (Ring and Ball Method) of Thermoplastic Material

Street 13/ Asphalt

1. Hari Sasidharan 2. Babi Lal 3. Abdul Rahman 4. Rashid Rajon


BS 3262-1:1998 Ap. C Method C

Binder Content of Thermoplastic Material

Street 13/ Asphalt

1. Chandra Narayanan 2. Ramudesh 3. Babhi Lal 4. Abdul Rahman 5. Rashid Rajon 6. Prakash Karki


BS 3262-3:1989 Ap. B

Dry Film Thickness Street 13/ Asphalt

1. Chandra Narayanan 2. Ramudesh 3. Babhi Lal 4. Abdul Rahman 5. Rashid Rajon


BS EN 1426-2015 Determination of Needle Penetration

Street 13/ Asphalt

1. Hari Sasidharan 2. Abdul Rahman 3. Bhabi Lal


BS EN 1427-2015 Determination of Softening Point (Ring and Ball METHOD)

Street 13/ Asphalt

1. Hari Sasidharan 2. Babi Lal 3. Abdul Rahman 4. Rashid Rajon


BS EN 12697-1:2012 centrifuge extractor method

Soluble binder content Street 13/ Asphalt

1. Bhabi Lal 2. Velautham Sachchutha 3. Hari Sasidharan


BS EN 12697-2:2015

Bituminous mixtures. Test method for hot mix asphalt. Determination of particle size distribution

Street 13/ Asphalt



BS EN 12697-5:2018

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the maximum density

Street 13/ Asphalt



BS EN 12697-6:2012

Bituminous mixtures. Test methods for hot mix asphalt. Determination of bulk density of bituminous specimens

Street 13/ Asphalt





Section Location /



BS EN 12697-8:2018

Bituminous mixtures. Test methods for hot mix asphalt. Determination of void characteristics of bituminous specimens

Street 13/ Asphalt



BS EN 12697-13:2017

Bituminous mixtures. Test methods for hot mix asphalt. Temperature measurement

Street 13/ Asphalt

1. Hari Sasidharan 2. Harison Aniwe 3. Bhabi Lal


BS EN 12697-23:2017

Determination of the indirect tensile strength of Bituminous specimens

Street 13/ Asphalt

1. Chandra Narayanan 2. Ramudesh 3. Babhi Lal 4. Abdul Rahman 5. Rashid Rajon 6. Hari Sasidharan


BS EN 12697-27:2017

Bituminous mixtures. Test methods for hot mix asphalt. Sampling

Street 13/ Asphalt

1. Hari Sasidharan 2. Harrison Aniwe 3. Bhabi Lal


BS EN 12697-28:2001

Bituminous mixtures. Test methods for hot mix asphalt. Preparation of samples for determining binder content, water content and grading

Street 13/ Asphalt



BS EN 12697-29:2002

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the dimensions of a bituminous specimen

Street 13/ Asphalt



BS EN 12697-30:2018

Bituminous mixtures. Test methods for hot mix asphalt. Specimen preparation by impact compactor

Street 13/ Asphalt



BS EN 12697-34:2012

Bituminous mixtures. Test methods for hot mix asphalt. Marshall test

Street 13/ Asphalt



BS EN 12697-39:2012

Bituminous mixtures. Test methods for hot mix asphalt. Binder content by ignition

Street 13/ Asphalt





Section Location /



QCS 2014 Section 06-05 Paragraph 16

Retained Stability (ASTM D6927)

Street 13/ Asphalt

1. Chandra Narayanan 2. Ramudesh 3. Babhi Lal 4. Abdul Rahman 5. Rashid Rajon

316 NA Rock ASTM D5873-2014 Determination of Rock Hardness by Rebound Hammer Method


317 1.01 Soil ASTM C702-2018 Standard Practice for Reducing Samples of Aggregate to Testing Size

Site/Street 13/ Soil

1. Jude Niroshan 2. Harrison Aniwe 3. Prakash Karki

318 2.01 Soil ASTM D75-2014 Standard Practice for Sampling Aggregates

Site/ Aggregate

1. Hari Sasidharan 2. Harison Aniwe 3. Ramudesh K 4. Abdul Rejon Rashid

319 1.04 Soil ASTM D1140-2017 Material finer than 0.075mm sieve

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Prakash Karki

320 1.08 Soil ASTM D1556-2015e1

Field Density (Sand Cone) Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Abdul Rejon Rashid 4. Prakash Karki

321 1.06 Soil ASTM D1557-2012e1

Lab compaction test using modified effort

Street 13/ Soil 1. Hari Sasidharan 2. Chandra Narayan 3. Prakash Karki

322 1.11 Soil ASTM D1883-2016 Standard Test Method for California Bearing Ratio (CBR) of Laboratory- Compacted Soils

Site/Stree t 13/ Soil

1. Hari Sasidharan 2. Jude Niroshan 3. Ramudesh K 4. Prakash Karki

323 1.02 Soil ASTM D2216-2019 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

Street 13/ Soil 1. Hari Sasidharan 2. Abdul Rahman 3. Prakash Karki 4. Chandra Narayan

324 1.13 Soil ASTM D2419-2014 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate

Site/ Street 13/ Soil

1. Hari Sasidharan 2. Jude Niroshan 3. Harison Aniwe 4. Prakash Karki




Section Location /


325 1.05 Soil ASTM D4318-2017e1

Liquid Limit, Plastic Limit, and Plasticity Index of soil

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Nikesh Mundayat 4. Prakash Karki

326 1.07 Soil ASTM D4718-2015 Correction of density and water content of soil

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Nikesh Mundayat

327 1.03 Soil ASTM D6913-2017 Standard Test Methods for Particle- Size Distribution (Gradation) of Soils Using Sieve Analysis

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Chandra Narayan 4. Prakash Karki

328 1.09 Soil ASTM D6938-2017a

Field density (Nuclear) Site/ Soil 1. Alex Santillan 2. Clark De Lara 3. Jonathan Hernandez 4. Jayson Enrile 5. Padam Bahadur 6. Ashwin Neupane 7. Shiran Rex 8. Allan Sampang 9. Roderick Galang 10. Stephen Gitau 11. Samuel Maina

329 1.14 Soil BS 1377-2 C3.2:1990

Methods of test for soils for civil engineering purposes. Classification tests. Moisture Content (Oven Drying)


330 1.15 Soil BS 1377-2:1990; Sec.4.3

Determination of Liquid Limit (Cone Penetrometer)

Street 13/ Soil 1. Hari Sasidharan

331 1.16 Soil BS 1377-2 C4.5:1990

Methods of test for soils for civil engineering purposes. Classification tests. Liquid Limit (Casagrande)


332 1.17 Soil BS 1377-2 C5.0:1990

Methods of test for soils for civil engineering purposes. Classification tests. Plastic Limit & Plasticity Index


333 1.18 Soil BS 1377-2 C9.2:1990

Methods of test for soils for civil engineering purposes. Classification tests. Wet Sieving





Section Location /


334 1.19 Soil BS 1377-2 C9.3:1990

Methods of test for soils for civil engineering purposes. Classification tests. Dry Sieving


335 1.25 Soil BS 1377-3 C3:2018 Organic Matter Street 13/ Chemistry

1. Jonalyn Ella 2. Md. Erphan 3. Rifan Ahmed 4. MM Aasik

336 1.28 Soil BS 1377-3:1990 C5.2,5.5

Methods of test of soils for civil engineering purposes. Chemical and electro- chemical tests: Determination of water soluble sulphate



337 1.29 Soil BS 1377-3:1990 C5.3, 5.5

Methods of test of soils for civil engineering purposes. Chemical and electro- chemical tests: Determination of acid soluble sulphate



338 1.26 Soil BS 1377-3:1990 C7.2

Methods of test of soils for civil engineering purposes. Chemical and electro- chemical tests: Determination of water soluble chloride



339 1.27 Soil BS 1377-3:1990 C7.3

Methods of test of soils for civil engineering purposes. Chemical and electro- chemical tests: Acid soluble chloride


1. Jonalyn Ella 2. Rifan Ahmed 3. MM Aasik

340 1.20 Soil BS 1377-4 C3.5:1990

Methods of test for soils for civil engineering purposes. Compaction-related tests. Dry Density

Street 13/ Soil 1. Hari Sasidharan 2. Jude Niroshan 3. Jayson Enrile 4. Prakash Karki

341 1.20 Soil BS 1377-4 C3.6:1990

Methods of test for soils for civil engineering purposes. Compaction-related tests. Moisture Content

Street 13/ Soil 1. Hari Sasidharan 2. Prakash Karki




Section Location /


342 NA Soil BS 1377-4:1990 Section 4.3

Methods of Test for Soils for Civil Engineering Purposes. Compaction-Related Tests

Street 13/ Soil 1. Hari Sasidharan

343 1.21 Soil BS 1377-4 C7.0:1990

Methods of test for soils for civil engineering purposes. Compaction-related tests (CBR)

Site/ Soil 1. Hari Sasidharan

344 1.23 Soil BS 1377-9:1990 Sec. 2.2

Methods for Test for Soils for Civil Engineering Purposes. In- Situ Tests (Sand Replacement)


345 1.24 Soil BS 1377-9 C2.5:1990; BS EN 1997-2:2007; BS EN ISO 22476-2:2005 +A1:2011; BS EN ISO 22476-3:2005 +A1:2011; BS EN ISO 22476-1:2012

Methods for test for soils for civil engineering purposes. In-situ tests (Nuclear Gauge Method)

Site/ Street 13/ Soil

1. Alex Santillan 2. Clark De Lara 3. Jonathan Hernandez 4. Jayson Enrile 5. Padam Bahadur 6. Ashwin Neupane 7. Shiran Rex 8. Allan Sampang 9. Roderick Galang 10. Stephen Gitau 11. Samuel Maina

346 1.31 Soil BS 1924-2:2018 C4.2

Method of Test for Cement Stabilized Materials

Site/ Street 14

1. Sujith Sudarsan 2. Rarish Gopala Pillai 3. Sujanthan Arumugan 4. Sangeethan Sekeran

347 1.30 Soil BS EN 933-8:2015 Tests for geometrical properties of aggregates, Part 8: Assessment of fines — Sand equivalent test

Street 13/ Soil 1. Hari Sasidharan 2. Rajneesh Parmar 3. Harrison Aniwe

348 7.02 Steel ASTM A370-2019e1 Standard Test Methods and Definitions for Mechanical Testing of Steel Products

Street 14/ Steel

1. Allan Abinguna 2. Mahendra Singh




Section Location /


349 NA Steel ASTM A615-2018e1 Cl 9,10,11

Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement. 9. Tensile Requirements. 10. Bending Requirements 11. Permissible Variation in Weight [Mass]

Street 14/ Steel


350 7.10 Steel ASTM A931-2018 Tension Testing of Wire Ropes and Strand

Street 14/ Steel

1. Mahendra Sing Budhathoki 2. Daniel Kwaku Nutassey

351 7.09 Steel ASTM A1061-2016 Standard Test Methods for Testing Multi-Wire Steel Prestressing Strand

Street 14/ Steel


352 7.03 Steel BS 4449:2016 C7.2.5

Steel for the reinforcement of concrete. Weldable reinforcing steel. Bar, coil and decoiled product. Specification

Street 14/ Steel


353 7.11 Steel BS EN 124-1:2015 Annex "A" and Annex "B"

Load Resistance Test Of Manhole Covers

Street 14/ Steel


354 7.01 Steel BS EN 10002-1:2001 BS EN ISO 6892-1:2016

Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature

Street 14/ Steel


355 NA Steel BS EN ISO15630-1:2019 Cl 5.3

Steel for the reinforcement and prestressing of concrete — Test methods Part 1: Reinforcing bars, wire rod and wire

Street 14/ Steel


356 7.08 Steel BS EN 15630-3:2019 CL 5, 6, 7

Steel for the reinforcement and prestressing of concrete - Test methods Part 3: Prestressing Steel. CL 5 Tensile Test. CL 6 Bend Test. CL 7 Reverse Bend test

Street 14/ Steel


Documents

ADVANCED CONSTRUCTION TECHNOLOGY SERVICES-QATAR · ADVANCED CONSTRUCTION TECHNOLOGY SERVICES-QATAR . GATE 172, STREET 13 . INDUSTRIAL AREA, PO BOX NO 22159 . DOHA, QATAR . Testing