ADDITIONS AND ALTERATIONS LAUREL HIGHLANDS HIGH … · Wood Veneer: Plain sliced, same veneer as door faces with book matching grain in same direction as grain of door. 3. Panel Profile:

Eckles Architecture & Engineering 301 North Mercer Street New Castle PA 16101 724 652 5507 fax 724 652 0751

www.EcklesGroup.com

TRANSMITTAL and RETURN RECEIPT ADDITIONS AND ALTERATIONS LAUREL HIGHLANDS HIGH SCHOOL LAUREL HIGHLANDS SCHOOL DISTRICT NORTH UNION TOWNSHIP, FAYETTE COUNTY, PENNSYLVANIA

EA PROJECT No. 09033.000

ALL PRIME BIDDERS: Addendum 5 is attached and available at the DFS planroom at www.MyPrintScape.com, or by contacting Printscape Imaging and Graphics at 412 788 0640 67 pages including transmittal cover sheet and attachments, Also attached for information only: 49 pages of Pre-Bid Requests for Information with responses. You must acknowledge receipt of this addendum on the bid form and by signing the bottom portion of this transmittal upon receipt and sending via FAX 724 652 0751 to Eckles. Acknowledge of Receipt of this Addendum: CONTRACTOR _____________________________________________________________________________ Contact Name ______________________________________________________________________________ Date Received __________________________________________________ Except for Addenda, information posted at the website or distributed electronically will not be part of the Contract Documents. Bidders must confirm receipt of Addenda both by return fax and on the bid form.

09033 ADDS & ALTS LAUREL HIGHLANDS HS ADDENDUM 5 Page 1 of 23

ADDENDUM 5

ADDITIONS AND ALTERATIONS LAUREL HIGHLANDS HIGH SCHOOL LAUREL HIGHLANDS SCHOOL DISTRICT NORTH UNION TOWNSHIP, FAYETTE COUNTY, PENNSYLVANIA

EA PROJECT No. 09033.000

September 28, 2012

GENERAL 1. This Addendum shall supplement, amend, and become a part of the Bid Documents. All bids and the construction contract shall be based on these modifications. 2. Bidder shall acknowledge the receipt of this Addendum on the Bid Proposal Form.

PRIOR ADDENDA

Item No 5.1 Addendum Item 2.28 HM100, HM101 AND HM102 COMPREHENSIVE ABATEMENT PLANS

ASBESTOS ABATEMENT GENERAL NOTES; DELETE Note #6. The adhesives at the chalkboards is not asbestos containing material. The chalkboards and tackboards shall be removed by the GC.

Item No 5.2 Addendum 3, Supplemental Drawing SDA-11

Elev 38; CHANGE Tag E-1 to instead read C-1.

PROJECT MANUAL

Item No 5.3 00 4116.04 BID FORM- ELECTRICAL CONSTRUCTION

REPLACE page 3 with the page attached to this Addendum

Item No 5.4 00 7216 CONDITIONS OF THE CONTRACT

AIA A232, § 2.2.5; CHANGE the first sentence to read as follows: Unless otherwise provided in the Contract Documents, the Owner shall furnish to each Prime

Contractor six copies of the Contract Documents …


Item No 5.5 01 1200 MULTIPLE CONTRACT SUMMARY

Article 1.06; ADD Paragraph F. to read as follows: F. Auditorium: Prior to start of work or ordering of equipment in this area, GC to convene

preinstallation meeting with HC, EC and TCC to locations, installation and sequencing of power, lighting, theatrical lighting, acoustical reflectors, diffusers and registers, communication, sound and technology, and other critical features of the overall auditorium design.

Article 1.07, Paragraph B.; ADD SubParagraph B.3.a. to read as follows: a. Auditorium: Prior to start of work or ordering of equipment in this area, participate

in GC preinstallation meeting to coordinated critical features of the overall auditorium design.





Item No 5.6 01 2200 - UNIT PRICES

Article 3.01, Paragraph C.; CHANGE Undercut Material quantity in SubParagraph C.1.b. to read as follows:

Undercut Material = 1,000 cu yd to be reworked and compacted as engineered fill 6,300 cu yd be hauled off site NOTE: Undercut quantities include utility trench spoils by other Prime Contractors.

Article 3.04; ADD Paragraph B. to read as follows: B. Unit Price UE-8: IMPORTED BACKFILL

1. Description: Importing and placing suitable backfill (as judged by the OGE) , including all processing and conditioning, for utility trenches under walks and paved areas, in compliance with Excavation & Backfill Note #2 on Drawing PS401. a. Removal of excavated utility trench material, and backfilling of trenches using on-

site material, are to be included in the Base Bid price, with no cost adjustment for field changes.

b. Spoils from trenching through PEMs may be deposited on site for removal by GC. c. Unit cost applies only to stone backfill imported for trenches under paving. d. Base Bid quantity = 600 CY.

2. Measurement and Payment: In-place, compacted cubic yard of backfill material, determined by field-measuring and/or surveying. a. Counting of trucks may be used as a check for reasonableness, but shall not be used

to determine the actual payment amount


Item No 5.7 01 5000 TEMPORARY FACILITIES AND CONTROLS

Article 3.19, Paragraph A.; CHANGE SubParagraph A.2. to read as follows: 2. Provide and pay for all connection and usage fees for broadband internet service capable of

at least 5 mbps bandwidth and provide connectivity to each of the four individual offices. Satellite-based internet connections are not acceptable.

.. and CHANGE SubParagraph A.8. to read as follows: 8. One multifunction copy/scan/print/fax device equal to Xerox WorkCentre 7525 capable of

making multiple copies, collating, 8-1/2 x 11 inch paper, 8-1/2 x 14 inch paper, and 11 x 17 inch paper. Device shall have color printing and copying capabilities. Maintain consumables and technical support service throughout project.

.. and DELETE SubParagraph A.9.

Item No 5.8 06 4000 ARCHITECTURAL/WOODWORKING FINISH CARPENTRY

Article 1.01, Paragraph A.; CHANGE SubParagraph A.2.c. to read as follows: c. Decorative resin panels

.. and ADD SubParagraph A.5. to read as follows: 5. Wall-mounted Decorative Signage

a. Decorative resin panels on stainless-steel standoffs a. Magnetic laminated glass panels on stainless-steel standoffs

Article 2.01; CHANGE Paragraph B. to read as follows: B. Wood Species and Cut for Transparent Finish: Red Oak, plain sliced, except as otherwise

scheduled or noted on Drawings.

.. and ADD Paragraphs H. and I. to read as follows: H. Pressed Glass Panel: Solid-color laminated architectural safety glass.

1. Pressed Glass C3 Color one-layer by 3form USA. Type, Pattern, Color as scheduled

I. Magnetic Dry-Erase Glass Board: 3/16-in (5mm) single-sided colored tempered magnetic safety glass, predrilled for mounting on wall using stainless steel standoffs. 1 Basis of Design: Eisys-inc., Borks Frameless Laminated Magnetic Glass Product.

a. 1 pieces of 4mm starphire tempered glass with 1mm steel magnetic interlayer b. Custom background color with custom text graphic on one side as detailed on the

Drawings. Provide RED equal to SW 6863(P4) Lusty Red c. Include additional paint barrier on each piece of glass to ensure full color resolution –

tempering process to follow painting, laminating and curing process

2. Accessories: Eisys/Borks premium framed glass board accessory pack – HAE8149-P. a. 5 neon dry erase pens, b. 1 rectangular eraser, c. 10 eraser refills, d. pkg of 6 strong magnets, e. 1 box of eximo, f. 1 magnetic pen shelf


3. Manufacturing Tolerances: a. Deflection tolerance 2 mm/ 2m b. Tolerance on sizes +0-2mm c. Max length/width ratio 1/10

6. Typ Locations: Concession Area. Refer to DS19 on A350

9. Contact: Tim O’Neil & Assoc – Jennifer Lindemuth, 412 953 1005 - [email protected]

Article 2.10; ADD Paragraph C. to read as follows: C. Framed Partition: 200.16.05 Frame Hardware System by 3form USA.

Item No 5.9 08 1113 HOLLOW METAL DOORS AND FRAMES

Article 1.05; CHANGE Paragraph G. to read as follows: G. Temperature-Rise Limit: Where indicated, required by applicable codes, at vertical exit enclosures

(stairway openings) and exit passageways, provide doors, frames and openings that have a maximum transmitted temperature end point of not more than 450 deg F above ambient after 30 minutes of standard fire-test exposure

Item No 5.10 08 1416 FLUSH WOOD DOORS

Article 2.03; ADD Paragraph D. to read as follows: D. Wood Panel Side or Transom Inserts: Fabricate matching panels with same construction, exposed

surfaces, and finish as specified for associated doors. 1. Core and Construction: Match adjacent solid-core door slab.

2. Wood Veneer: Plain sliced, same veneer as door faces with book matching grain in same direction as grain of door.

3. Panel Profile: Flush panel. Fabricate panels to insert into standard HM frame. Provide factory-installed spring bolts for concealed attachment into jambs of metal door frames.

Item No 5.11 08 7100 Attachment: DOOR HARDWARE SETS

REPLACE Hardware Shedule with the attached revised 08 7100 Attachment Sets 58, 70 and 71 changed electric strikes to integrated locks Exterior Doors, door position switches were added to sets 1,2, 3, 4, 5, 6, 8, 9, 10, 12, and 86 Set 86 changed strike type Set 89 had lock tester added


Item No 5.12 08 8000 GLAZING

GENERAL: Disregard references to Patterned Glass . There is none used on this Project.

Article 2.03; CHANGE Paragraphs B. and C. to read as follows: B. Low-E Insulated-Glass Units: Annealed or Kind HS (heat-strengthened) typical, or Kind FT

(fully tempered) where indicated or required by authority having jurisdiction. 1. Overall Unit Thickness and Thickness of Each Lite: 1-inch and 1/4-inch minimum. 2. Interspace Content: Argon 3. Outdoor Lites: Class 1 (clear) float glass. Kind FT (fully tempered) 4. Interior Lites: Class 1 (clear) float glass. Kind FT (fully tempered) 5. Low-E Coating: Solarban 60 where indicated on surface 2. 6. Spandrel Coating: Sputter coating where indicated on surface 3

C. Low-E Insulating-Glass Units For Exterior Doors: 1. Overall Unit Thickness and Thickness of Each Lite: 5/8-inch and 1/8-inch minimum. 2. Interspace Content: Argon. 3. Outdoor Lite: Class 2 (clear) float glass Kind FT (fully tempered) 4. Indoor Lite: Class 1 (clear) float glass Kind FT (fully tempered) 5. Low-E Coating: Solarban 60 on surface 2.

.. and DELETE Paragraph D.

ADD Articles 2.07 through 2.09 to read as follows: 2.07 SPECIALTY GLAZING PANELS

A. Magnetic Dry-Erase Glass Boards: 3/8-in (9mm) colored tempered magnetic safety glass with custom logo, for glazing into existing HM frames. 1 Basis of Design: Eisys-inc., Borks Frameless Laminated Magnetic Glass Product.

a. 2 pieces of 4mm starphire tempered glass with 1mm steel magnetic interlayer b. Custom background color with two-color custom logo graphic on both sides as

detailed on the Drawings

2. Color: a. Field Color: RED equal to SW 6863(P4) Lusty Red b. Custom Logo: Digitally produced 2 color graphic -

SW7007(P3) Ceiling Bright White, and SW 6966(P5) Blueblood

3. Process: Include additional paint barrier on each piece of glass to ensure full color resolution – tempering process to follow painting, laminating and curing process.

4. Accessories: Eisys/Borks premium framed glass board accessory pack – HAE8149-P. Provide 1 package at each entrance system within each scheduled room. Includes the following: a. 5 neon dry erase pens, b. 1 rectangular eraser, c. 10 eraser refills, d. pkg of 6 strong magnets, e. 1 box of eximo, f. 1 magnetic pen shelf

5. Manufacturing Tolerances: a. Deflection tolerance 2 mm/ 2m b. Tolerance on sizes +0-2mm c. Max length/width ratio 1/10


6. Typ Locations: as scheduled

7. Fire-Rated Locations: Frames at Door No B112.1, B113.1, F118.1, F119.1, F120.1, F122.1, F123.1, B203.1, B202.1, B201.1, B200.1

8. Special Conditions: a. Single-Sided Glass to be used in conjunction with Fire Rated Frame and Glass per

local codes and as noted on plans b. Contractor to determine proper method of installing Magnetic Glass on exterior along

with Special Fire Rated Color Logo Gass on interior of classroom side lites as necessary

c. Contractor to coordinate color match, logo match, magnetic properties and code compliance

9. Contact: Tim O’Neil & Assoc- Jennifer Lindemuth, 412 953 1005; [email protected]

B. Insulating Metal Glazing Panels: 1. Construction:

0.032” Kynar, Smooth Aluminum Skin – Color as scheduled Polymer Substrate Polystyrene Core Polymer Substrate 0.032 Kynar, Smooth Aluminum Skin – Color as scheduled

2. Product and Manufacturer: As specified in Section 08 4113 “Aluminum Framed Entrances and Storefront”

C. Interior Metal Glazing Panels 1. Construction:

0.032” Kynar, Smooth Aluminum Skin – Color as scheduled Polymer Substrate Core 0.032 Kynar, Smooth Aluminum Skin – Color as scheduled

2. Manufacturer: Insulating Metal Panel Manufacturer

D. Wood Veneer Panel Inserts: As specified in Section 08 1416

2.08 FIRE RATED GLAZING

A. General: 1. Use products selected from among those specified, as appropriate for specific application

and in compliance with requirements. 2. Fire-Rated Window Assemblies: Assemblies complying with NFPA 80 that are listed and

labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to NFPA 257. Glazing shall be CPSC CAT II.

3. Glazing for Fire-Rated Door Assemblies: Glazing for assemblies that comply with NFPA 80 and that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to NFPA 257. Glazing shall be CPSC CAT II.


B. Film-Faced Ceramic Glazing Material: Proprietary Category II safety glazing product in the form of a 3/16-inch- thick, ceramic glazing material polished on both surfaces, faced on one surface with a clear 3M Scotchshield glazing film, and as follows: 1. Fire-Protection Rating: As indicated for the assembly in which glazing material is installed,

and permanently labeled by a testing and inspecting agency acceptable to authorities having jurisdiction.

2. Product: a. FireLite NT by Nippon Electric Glass Co., Ltd., distributed by Technical Glass

Products b. Keralite FR-F by Vetrotech Saint-Gobain International distributed by R.J. Bridges

Corp. 412-276-9300.

C. Laminated Ceramic Glazing Material: Proprietary Category II safety glazing product in the form of 2 lites of clear ceramic glazing material laminated together to produce a laminated lite of 5/16-inch nominal thickness; weighing 4 lb/sq. ft.; and as follows: 1. Fire-Protection Rating: As indicated for the assembly in which glazing material is installed,

and permanently labeled by a testing and inspecting agency acceptable to authorities having jurisdiction.

2. Polished on both surfaces, transparent. 3. Product: "FireLite Plus" by Nippon Electric Glass Co., Ltd., and distributed by Technical

Glass Products.

D. Clear Fire-Rated Glazing with Intumescent Interlayer: safety glazing product utilized in both Interior and Exterior Applications. 1. Fire Protection Rating: As indicated for the assembly in which glazing material is installed,

and permanently labeled by a testing and inspection agency acceptable to authorities having jurisdiction. a. Pilkington Pyrostop as manufactured by the Pilkington Group and distributed by

Technical Glass Products. b. Contraflam as manufactured by Vetrotech Saint-Gobain International distributed by

R.J. Bridges Corp. 412-276-9300.

E. Glazing Sealants for Fire-Resistive Glazing Products: Identical to products used in test assemblies to obtain fire-protection rating.

2.09 INTEGRAL BLINDS

A. Integral Horizontal Louver Blinds: Provide remotely operated horizontal louver miniblinds in the space between outer I.G. unit and inner fixed lite. 1. Subject to compliance with requirements, provide manufacturer's standard or recommended

Horizontal Louver Blinds, aluminum louver slats, manual tilt operation, fixed in place between panes of dual glazed unit constructed of inner sheet of glass in a removable sash for access to interior of unit, installed with airtight gaskets

B. Louver Slats: Aluminum, alloy and temper recommended by producer for type of use and finish indicated; with crowned profile. 1. Nominal Slat Width: 1-inch-thick for miniblinds. 2. Internal Glass Airspace: 1.5-inch minimum. 3. Nominal Slat Thickness: Not less than 0.008 inch. 4. Slat Material: Aluminum alloy 6010-T8 with head and bottom rail or 6063-T5 alloy. 5. Finish: Baked polyester or enamel finish in one color as indicated, or as selected by

Architect from manufacturer’s full lines of available colors.


Item No 5.13 09 2116 GYPSUM BOARD ASSEMBLIES

Article 3.08, Paragraph A.; CHANGE SubParagraph A.5. to read as follows: 5. Impact-Resistant Type: Corridors, except as noted, to height of 8’ – 0” above finish floor.

a. Exception: At locations scheduled for ceramic tile finish, provide approved tile backer board.

Item No 5.14 09 5113 ACOUSTIC PANEL CEILINGS

Article 2.05, Paragraph A.; CHANGE SubParagraph A.1. to read as follows: 1. Basis-of-Design: Axiom Vector, Classic Trim Straight - 6" Channel

.. and ADD Paragraph D. to read as follows: D. Application – as follows and as indicated in Reflected Ceiling Plans:

1. Type 13 ceiling in Engineering C000 and Information Tech C001, 2. Type 6 ceiling in Upper Band Classroom A109 and Upper Music Classroom A110 3. Type 7 ceiling in Upper Lobby A104g and Vestibule B108

Appendix, Page 6 of 6; ADD Ceiling Type 17 to read as follows: TYPE -17 1-HR FIRE-RATED CLG

A. Basis of Design Product: 605 Ceramaguard Fire Guard by Armstrong. Composition: Ceramic and mineral fiber composite Color: White Size: 48in x 24in x 5/8in Edge Profile: Square Lay-In Dimensional Stability: HumiGuard Plus 10-year limited warranty against sag.. Antimicrobial Protection: Inherent Fire Resistive

B. Appearance Characteristics: Type and Form: Type XX, high-density ceramic-like composition with scrubbable finish Pattern: G (lightly textured)

C. Performance Qualities: LR: Not less than 0.88 NRC: N/A CAC: Not less than 38

D. Grid: Armstrong Prelude Plus XL FireGuard 15/16” or acceptable product by accepted tile manufacturer.

E. Application – as follows and as indicated in Reflected Ceiling Plans: Elev Eq E001, Elev Eq B003 1. Provide ceiling system as part of UL-approved 1-hour fire-resistance rated floor/ ceiling

assembly.


Item No 5.15 09 6115 TERRAZZO PATCHING AND RESTORATION

Article 2.02; ADD Paragraph D. to read as follows: D. Anti-Slip Tape: Min 2-in wide self-adhering safety surface for application on existing terrazzo

stair treads. 1. Flex-Tred heavy duty safety tape and installation accessories by Wooster Products 2. Colors as selected by Architect from manufacturer’s full range.

Article 3.03; ADD Paragraph D. to read as follows: D. Remove existing safety surface on terrazzo stairs and prepare substrate per manufacturer’s

instructions to receive new Anti-Slip Tape.

Article 3.04; ADD Paragraph J. to read as follows: J. Anti-Slip Tape: Install in accordance with manufacturer’s recommendations and authority having

jurisdiction.

Item No 5.16 09 6516 - LINOLEUM FLOORING

Article 2.01, Paragraph A.; ADD SubParagraph A.3. to read as follows: 3. Contact: Ohio Valley Flooring, Kathy Latine 440-263-3878; [email protected]

Item No 5.17 09 6800 - CARPETING

Article 2.02, Paragraph A.; CHANGE SubParagraph A.1. to read as follows: 1. Manufacturer: Atlas Carpet Mills , as scheduled on Drawings

a. Style, color and pattern as scheduled and indicated on the Drawings. b. Backing: Provide Firma Cushion Bac Polyurethane carpet backing

Article 2.02, Paragraph B.; CHANGE SubParagraphs A.3. through 6. to read as follows: 3. Tile Size: Mfr Std. 19.7 inch x 19.7 inch. 4. Dry Soil Retardant: DuraTech by Invista, or manufacturer’s recommended equivalent. 5. Bonding Agent: Manufacturer’s Standard. 6. <delete>.


Item No 5.18 09 8400 ACOUSTIC ROOM COMPONENTS

CHANGE Article 2.05 to read as follows: 2.05 FABRIC-WRAPPED SOUND ABSORPTIVE PANEL/ TACKBOARD:

A. Back-Mounted, Edge-Reinforced Acoustical Wall Panels: Manufacturer's standard panel construction consisting of facing material laminated to front face, edges, and back border of dimensionally stable, polyester-fiber board core; with edges chemically hardened to reinforce panel perimeter against warpage and damage; and complying with the following requirements: 1. Facing Material: Manufacturer's standard woven polyester fabric from same dye lot; color

and pattern as scheduled on Drawings. 2. Nominal Core Density: 7.5 lb/cu. ft. 3. Nominal Overall Panel Thickness and Noise Reduction Coefficient: 1 inch and not less than

NRC .075 for Type A mounting per ASTM E 795. 4. Panel Width: Manufacturer's standard. 5. Panel Height: As indicated. 6. Edge Detail: Square. 7. Corner Detail: Square.

B. Basis-of-Design Product: Vertical Wall Solutions, as represented by Fashion Wallcoverings, Cleveland, OH 44103

Item No 5.19 11 5213 PROJECTION SCREENS (from Addendum 3)

Article 2.01, Paragraph A; DELETE SubParagraph A.4.a. Auditorium projection screen is specified elsewhere in Contract Documents.

Article 2.01, Paragraph A; CHANGE SubParagraphs A.4.b. to read as follows: b. Cafeteria C103 (Recessed Clg-Mtd ) & Library C202 (Wall-Mtd) locations:

Tensioned Advantage Electrol. 1) Screen Size (HDTV Format): 70-inches high by 108-inches wide. Provide

white viewing area 66 inches high by 104 inches wide. 2) Edge Treatment: Black masking borders with 2” black drop at all sides. 3) Casing, ceiling closure unit: Aluminum designed for ceiling-recessed

installation with white painted finish. 4) Wall-mount Brackets: Provide Manuf. recommended Wall Brackets with 6-

inch extension from wall. Mount Bracket as such that screen top is at 8’-0”AFF. Coord all installation locations with Architect prior to fabrication.

Item No 5.20 11 5314 CASEWORK EXHAUST EQUIPMENT

Article 2.04, Paragraph A.; CHANGE SubParagraphs A.1. and 2. to read as follows: 1. Millennia Series 100 Airfoil Single-Sided and Series 200 Double-Faced, by Air Master

Systems. a. Include blower, motor and controls. Provide integral blower switch, box, faceplate,

conduit, and wiring. Connection to power by EC..

2. Provide model numbers and associated equipment for each hood as detailed on Drawing 8/A352.


Item No 5.21 11 6623 - GYMNASIUM EQUIPMENT

6. Wall Padding

ADD Article 2.09 to read as follows: 2.09 WALL PADDING

A. Wall Wainscot Padding. Model 4100 Wall Padding as manufactured by Performance Sports Systems, Noblesville, Indiana. 1. Provide wall wainscot padding as shown on drawings. Each panel shall be 2’-0” wide x 6’-

10” high. Foam filler shall be 2” thick bonded polyurethane foam with a weight of 6 pounds per cubic foot. Foam shall be cemented to 7/16” wood backing board and covered with flame retardant, vinyl laminated polyester, folded and stapled to back of board. Provide 1” nailing margin top and bottom. Cover material shall have a certificate of flame resistance from the state of California. The cover material shall have anti-fungal and anti-bacterial agents and is easily cleaned using mild soap and water. Color selected from manufacturer’s standard offerings.

2. Pad covers flame resistance ratings: passes NFPA 701

3. Provide custom panels as required to accommodate layouts as indicated on the Drawings or as required by adjacent construction; include corner returns and finished cutouts where applicable.

Item No 5.22 12 3200 MANUFACTURED WOOD CASEWORK

Article 1.01, Paragraph B.; CHANGE SubParagraph B.2. to read as follows: 2. Custom casework at the following locations. All casework countertops edgebanding in

these locations shall be 1 1/4” eased oak wood at all exposed edges unless noted as SS1 countertops. Miter all corners. Wood finish shall be as selected by Architect. Refer to detail 1/A353 for wood edgebanding profile detail:

Reception E103, E103k, Library C202, Admin. Reception/Waiting G100/102

Article 2.07, Paragraph C.; CHANGE SubParagraph C.3. to read as follows: 3. Color: Epoxy Resin - #09 Blue. (Contact: 1-800-424-5254)

Appendix A-Casework Schedule, Page 2.; CHANGE Cabinet Mark MC-1 as follows: Under “Remarks”, Disregard references to solid door cabinets. Acousti-Grille Doors shall be provided…

Appendix A-Casework Schedule, Page 6.; CHANGE Cabinet Mark MC-42 as follows: Cabinet Description: Mobile Triple Bass Rack Stevens Industries Equal Model No.: 56204 Cabinet Details : - <no change> Remarks: Provide Carpeted Horizontal Base rails.

Edges shall be provided with high-impact edge extrusions.


Item No 5.23 12 6600 TELESCOPING BLEACHER SYSTEM

Article 2.03, Paragraph A.; CHANGE SubParagraphs A.1. and 2. to read as follows: 1. Row Spacing: 22 inch. 2. Row Rise: 9 5/8 inch.

Item No 5.24 13 1113 SWIMMING POOL

Article 1.05, Paragraph A.; CHANGE SubParagraph A.2. to read as follows: 2. GC may be required to provide additional information with regard to Pool Installer

Subcontract after award of bid: a. Furnish complete evidence that the Bidder has the facilities, equipment, personnel,

and resources to complete the Work. b. Show evidence of bondability from acceptable surety. c. Complete and submit the attached “Statement of Pool Contractor Qualification”

forms.

Item No 5.25 22 3000 PLUMBING INSULATION

Article 1.06; CHANGE Paragraph E. to read as follows: E. Hot equipment insulation shall be installed on the reconditioned hot water storage tank.

Item No 5.26 32 1216 ASPHALT PAVING

Article 2.01, Paragraph B.; CHANGE SubParagraph B.1. to read as follows: B. Asphalt seal coat: MasterSeal Concentrate Asphalt Based Pavement Sealer by SealMaster

Pavement Products (www.sealmaster.net; 800-395-7325) or approved equal.

DRAWINGS

Item No 5.27 CS101, CS101.1 CODE REVIEW PLANS – FIRST FLOOR

CHANGE Fire Barrier at Kitchen C102 per attached Supplemental Drawing SDA-17

Item No 5.28 CS400 – CS404 BUILDING PHASING PLANS, SCHEDULE AND NOTES

CHANGE Drawings per attached Supplemental Drawings CS400 through CS404 (r2 9/26/12) Phase 1 Finish: June 1, 2013

Phase 4 Start: September 1, 2013 Finish: February 1, 2014

Change the following spaces from Phase 5 to Phase 8: B225 Stair 4, B204 Corridor, E200 Storage, E201 Stair 7, E202a Entry, E204a Tlt Entry, E204 Womens Tlt, E205 Jan, E205b Entry, E206a Tlt Entry, E206 Mens Tlt, B108 Upper Vestibule, E104 Upper Vestibule; E106a Entry, E106b Entry, E107a Tlt Entry, E107 Mens Tlt, E108 Jan, E109a Tlt Entry, E109 Womens Tlt


Item No 5.29 C1-01 SITE PLAN AND SITE DIMENSIONING PLAN (BASE BID)

Construction Notes; CHANGE Note C-26 per attached Supplemental Drawing SDC-10

Item No 5.30 C8-02 SITE CONSTRUCTION DETAILS

Bituminous Seal Coat Detail; CHANGE Drawing per attached Supplemental Drawing SDC-9

Item No 5.31 ALL CIVIL DRAWINGS

ADD the following note to each drawing: The existing salt storage area/concrete pad on the east side of the

maintenance building will remain in the Base Bid and in Alternate Bids G-1 and G-2. If Alternate Bid G-2 is accepted, the location of the salt storage area/pavement shall be field verified and the proposed road on the east side of the maintenance building will be adjusted as necessary to accommodate the existing salt storage area.

Item No 5.32 HM100 COMPREHENSIVE ABATEMENT PLAN – GROUND FLOOR

Rooms E032, E033 and E034; ADD – Hazardous Materials Keynote Tag #3 indicating the the exterior windows. These windows shall be removed by the ACC and the opening closed by the GC

Item No 5.33 HM101 COMPREHENSIVE ABATEMENT PLAN – FIRST FLOOR FLOOR

Vestibule E110a and Corridor E110; ADD Hazardous Materials Keynote Tag #1 indicating the flooring at the doors to Gymnasium E146. These floor areas are at the sloped floor at the recess to these doors.

Cafeteria E126; ADD Hazardous Materials Keynote Tag #1 indicating the flooring at the doors to Security Office E148. These floor areas are at the recess to these doors.

Rooms E116a and E118a; ADD Hazardous Materials Keynote Tag #2 indicating the flooring.


Item No 5.34 HM102 COMPREHENSIVE ABATEMENT PLAN – SECOND FLOOR PLAN

DELETE ABATEMENT LEGEND. Refer to the abatement report for hazardous materials.

Item No 5.35 A002, A002a, A002b DOOR SCHEDULES

Door Schedule – Ground Floor Area F, First Floor Area C, First Floor Area F: ADD the following to the COMMENTS column for Doors F006.2, F008.2, C100.3 and F110a.3:

SEE DETAIL 11 / A004a

Door Schedule – First Floor Area B, First Floor Area E, Second Floor Area B, Second Floor Area E: ADD the following to the COMMENTS column for

Doors B132.1, B132.2, E121.1, E121.2, B222.1, B222.2, E222.1, and E222.2 : SEE DETAIL 13 / A004a

Door Schedule – First Floor Area C: ADD the following to the COMMENTS column for Doors C102.5, C102.4, and C102.3:

SEE DETAIL 13 / A004a @ THIS LOCATION – BOTTOM OF HOOD SHALL BE MOUNTED @ 7’-6” & GYP BD ENCLOSURE SHALL BE MOUNTED @ 7’-4”. COORD MOUNTING HEIGHTS WITH OPENING SIZE AND LOCATION

Door Schedule – First Floor Area C: ADD the following to the COMMENTS column for Door C102.6:

SEE DETAIL 14 / A004a

Door Schedule – First Floor Area B, First Floor Area D: ADD the following to the COMMENTS column for

Doors B106.2, B106.3, D103a.5, D103a.4, and D103a.3 : SEE DETAIL 15 / A004a

General Door Notes; ADD Note 17 to read as follows: 17. AT EXISTING DOOR FRAMES THAT ARE TO BE REGLAZED WITH GLAZING TYPE G9,

MODIFY EXISTING FRAME AS REQUIRED FOR NEW GLAZING/WOOD PANEL THICKNESS. FILL EXISTING HOLES FOR GLAZING STOPS AND PROVIDE NEW HOLES IN LOCATIONS REQUIRED TO ACCOMMODATE NEW GLAZING/WOOD PANEL THICKNESS.


Item No 5.36 A007 COLOR SCHEDULE

Interior Color Scheme 1; EB1 - CHANGE Remarks to read:

APPLY THIS COLOR EDGEBANDING TO ALL CASEWORK BODIES, DOORS, & DRAWER FRONTS WHERE PL1 SHALL BE INSTALLED UNO, AND COUNTERTOPS WHERE PL4 & PL2 SHALL BE INSTALLED UNO

Interior Color Scheme 2; PL1 - CHANGE Manufacturer and Series to read: WILSONART, and

CHANGE Manufacturer manufacturer color and number to read: 7919-78 AMBER CHERRY

ADD EB3 to schedule as follows: Manufacturer and Series: DOELLKEN-WOODTAPE Manufacturer Color and Number: DW6098 SATIN STAINLESS Remarks: APPLY THIS COLOR EDGEBANDING TO ALL

CASEWORK BODIES, DOORS, AND DRAWER FRONTS WHERE PL2 SHALL BE INSTALLED UNO

Interior Color Scheme 3; PL1 - CHANGE Remarks to read:

APPLY THIS COLOR PLASTIC LAMINATE AT ALL CASEWORK BODIES, DOORS, AND DRAWERS IN ALL ROOMS UNO. ALL LOCATIONS SHALL BE INSTALLLED WITH WOOD GRAIN @ A VERTICAL ORIENTATION TYP. SEE MILLWORK DETAILS AS NOTED

PL3 - CHANGE Remarks to read: APPLY THIS COLOR PLASTIC LAMINATE TO ALL COUNTERTOPS IN THIS SCHEME UNO

Item No 5.37 A004a FRAME DETAILS

Detail 12; DELETE Insulated Coiling Door Detail. (Not used on this Project)

Item No 5.38 AD100, AD101 AND AD102 COMPREHENSIVE DEMOLITION PLANS

CLARIFICATION – Demolition keynote #3 refers to locations where hazardous and non hazardous flooring materials are present and are to be removed by either the ACC or the GC. The GC shall coordinate with drawings HM100, HM101 and HM102 for the extent of the removal to be performed by the ACC.

CHANGE Demolition keynote #7 to read as follows: REMOVE MISCELLANEOUS SURFACE MOUNTED ITEMS SUCH AS SHELVING, TACKBOARDS, CHALKBOARDS, PROJECTION SCREENS, SIGNAGE, ETC. WHERE DAMAGE TO EXISTING WALLS OCCURS, PATCH WALLS TO MATCH EXISTING CONDITIONS AND AS REQUIRED FOR INSTALLATION OF NEW FINISHES.


Item No 5.39 AD102 SECOND FLOOR COMPREHENSIVE DEMOLITION PLAN

Room E226; CHANGE three Demolition Keynote Tags #13 to read 18 at the the exterior windows in on the north wall of the space. These windows shall be removed by the ACC and the opening closed by the GC

CLARIFICATION – The hatch patterns in the stair towers and pool hallway do not pertain to abatement scope of work and is a concrete hatch pattern that should be disregarded.

Item No 5.40 A120, A120a FIRST FLOOR PLAN - AREA A

CHANGE Instrument Storage casework and add chase, per attached Supplemental Drawing SDA-18

Item No 5.41 A123 FIRST FLOOR PLAN - AREA D

Auditorium D103 – Note referencing “Low Wall at Front and Side of ADA Seating Platform”; ADD the following

SEE DETAIL 7/A340 FOR ALL LOW WALLS AT PLATFORM TYP.”

Item No 5.42 A132 SECOND FLOOR PLAN - AREA B

Classroom B201; ADD interior elevation tag pointing to South wall indicating 18 / A341 SIM OPP HAND

Item No 5.43 A132 SECOND FLOOR PLAN - AREA C

Computer Lab C200 & C201; CHANGE wall tag W6 to read SEE DETAILS 8, 9, 11 / A353

Item No 5.44 A133 SECOND FLOOR PLAN - AREA D

Spotlight Room D201a; Wood Cap at Low Wall shall be @ 3'-4"aff.

Item No 5.45 A310 INTERIOR LAYOUT PLAN – GROUND FLOOR PLAN - AREA A

CHANGE Drawing per attached Supplemental Drawing SDA-14 Weights A005; At West & South Walls provide mirrors continuous length of wall Fitness A006; At East & South Wall provide mirrors continuous length of wall . Refer to detail 6/ A354


Item No 5.46 A320, A320a INTERIOR LAYOUT PLAN – FIRST FLOOR AREA A

Wall-mounted mirrors shown in Practice Rooms are specified in 08 8300.

ADD Wall cabinets at Nurse A118 per attached Supplemental Drawing SDA-16

Music Classroom A110; At wall elevation marked 9/A343, ADD a tag identifying Music library at SE corner as E-2 (similar to SW corner of Band Classroom A109)

Robe Storage A110d; ADD elevation tag identifying South Wall as 19/A343 sim

Uniform Storage A109g and Robe Storage A110d; CHANGE note reading “see coat & rod detail 10/A354” to instead read “SEE WARDROBE DETAIL 13/A354

Corridor A107; on Drawing A320a, ADD elevation tags 8/A721 pointing to South sall, in two typical locations as shown on Drawing A320

Corridor D100a; On Drawing A320a, ADD elev tags 4a/A720 pointing to North Wall, 4a/A720 pointing to south wall and 4/A721 pointing to south wall, in typical locations as shown on A320.

Gymnasium A105; Equipment Tags “PE-4” shown on Drawing A320 also apply to Drawing A320a

Pool A106; ADD an Elevation Tag pointing to East wall indicating “4/A720 similar” Text shown shall be omitted and horizontal stripe shall be continuous at East wall. ADD an Elevation Tag pointing to North wall indicating “3/A720 similar”

CHANGE Instrument Storage casework and add chase, per attached Supplemental Drawing SDA-18

Item No 5.47 A323 INTERIOR LAYOUT PLAN – FIRST FLOOR AREA D

Control Room D103a; At West Wall, ADD elevation tag to read: 16/A343 sim

Item No 5.48 A324 INTERIOR LAYOUT PLAN – FIRST FLOOR AREA E

Reception E103k; CHANGE tag “VDB5C” to read VDB5

Item No 5.49 A331 INTERIOR LAYOUT PLAN – SECOND FLOOR AREA B

Special Ed Resource B202; ADD 1 movable VDB13.

Item No 5.50 A332 INTERIOR LAYOUT PLAN – SECOND FLOOR AREA C

CHANGE Computer Labs C200 and C201 per attached Supplemental Drawing SDA-15

Library C202; CHANGE Note referencing the Presentation Station to read SEE DTL 20/A352.


Item No 5.51 A340 AUDITORIUM ELEVATIONS AND DETAILS

Detail 7/A340; CLARIFICATION: All notes refer to ALL exposed sides of low wall, typical. Refer to Elev 32/A340.

Item No 5.52 A343 MISCELLANEOUS ELEVATIONS

Elevation 10; CHANGE per attached Supplemental Drawing SDA-18

Elevation 16; Verify kneespace dimension in field. Dimension shall very depending on installation location.

Item No 5.53 A344 MISCELLANEOUS ELEVATIONS

Elevations 43 and 44; ADD Millwork Elevations at C200 and C201 per attached Supplemental Drawing SDA-16

Item No 5.54 A351 VDB LEGENDS/ DTLS, LOCKER DTLS, DISP CASE DTLS

Visual Display Board Legend, VDB6; DELETE reference to Main Lobby B106, and ADD reference to read CORRIDOR E106

Item No 5.55 A352 TYPICAL CASEWORK DETAILS

Detail 18, note referencing fume Hoods shall be MODIFIED to read as follows: FUME HOOD @ Rm B206a, B207a, B214a, B214b, B216a, B220a, B221a, B223a, B224a SHALL BE EQUAL TO AIR MASTER SYSTEMS MODEL NO. EH-211-36 DOUBLE-SIDED FUME HOOD.

FUME HOOD @ Rm B203, B206, B209, B210, B219 SHALL BE EQUAL TO AIR MASTER SYSTEMS MODEL NO. 36MAF SINGLE-SIDED FUME HOOD.

Item No 5.56 A353 TYPICAL CASEWORK DETAILS

Detail 1; CHANGE Tag E-1 to instead read C-1

Detail 7; CHANGE title of detail to read: TYP ENLARGED STANDOFF DETAIL @ DS SIGNAGE, and CHANGE note reading “Provide the Following…” to instead read: PROVIDE RP1 TYP

Detail 8; CHANGE note reading “Wall Type as Scheduled” to instead read: 1/4” OAK WOOD VENEER ON 1/2” PLYWOOD @ EXPOSED SURFACES TYP UNO – FINISH SHALL MATCH ARCHITECTS SAMPLE. PROVIDE FINISHED PANEL @ EXPOSED SIDES TYP.

Detail 9; CHANGE dimension reading 5/8” to instead read: “3/4”

Details 10 & 10b; CHANGE references to detail 2c/A323 – to instead read 10a/A353

Detail 11; CHANGE Millwork Computer Lab per attached Supplemental Drawing SDA-16


Item No 5.57 A354 MISCELLANEOUS INTERIOR DETAILS

Detail 3; DELETE Detail. Defibrullator cabinets are existing to be relocated..

Detail 6; CHANGE Mirror Detail per attached Supplemental Drawing SDA-15

Details 9 & 9A; ADD a note to read: PROVIDE COAT HOOK AT THE FOLLOWING LOCKER ROOMS: A009a, A011c, A012a, A013c, A106e, A106h, B202

Detail 10; ADD a note to read: PROVIDE SHELVING AT THE FOLLOWING ROOMS: B129

Detail 11; ADD a note to read: PROVIDE AT THE FOLLOWING ROOMS: B115b, F110c, F110e

Detail 12; ADD a note to read: AT ROOM B128b, PROVIDE 2 ADJUSTABLE HEIGHT SHELVES ENTIRE LENGTH OF CLOSET – TO BE MOUNTED ABOVE WASHER/DRYER.

Detail 13; ADD a note to read: PROVIDE SHELVING AT ROOMS: A109g and A110d

.. and CHANGE note referencing shelf standards to read: PROVIDE (4) 4’HIGH SHELF STANDARDS…

Item No 5.58 A356 EQUIPMENT SCHEDULES

Casework Equipment Schedule; CHANGE Item Number C-10 as follows Item: FOLDER RACK Manufacturer: DISPLAYS 2 GO Model No : WD85110K Description: WOOD MAGAZINE RACK SINGLE POCKET LIGHT OAK FINISH (9.5”W x 7.5”H x 2.25”D).

Natatorium Equipment; NE-5 Pool Scoreboard to be provided under GC as part of Pool Installer Subcontract.

Item No 5.59 A422 REFLECTED CEILING PLAN – FIRST FLOOR – AREA C

Kitchen C102 and Dishwashing C102c – ADD Ceiling Notation to read: ACT-TYPE 1 8’-4” AFF

Kitchen C102; CHANGE Gyp Bd Blkhd adjacent to coiling doors as follows: height to be 7’-4” AFF and bulkhead shall be continuous wall to wall, running underneath coiling door hood. See detail 13/A004a


Item No 5.60 A720 WALL GRAPHICS

Drawing 10a/A720 Typ Low Wall Dtl @ Electric Water Cooler; CHANGE Note “SS 1” to instead read G1, and ADD note to read as follows:

NO PRESSED GLASS PANELS SHALL BE REQUIRED @ ELECTRIC WATER COOLERS @ POOL A106

ADD Cafeteria C103 S Elevation per attached Supplemental Drawing SDA-14

Item No 5.61 A721 WALL GRAPHICS

Detail 6/A721 is similiar in reference to the single VDB-14 elev as dimensioned & tagged on the West wall of Aud. Lobby D103b, except that Base shall be as scheduled on A006. Provide Wood Base as scheduled in all of Auditorium D103 and Auditorium Lobby D103b.

Item No 5.62 SP-1 SWIMMING POOL PLAN AND SECTIONS

POOL PLAN AND EQUIPMENT LAYOUT, Tag 1A - Evacuator Duct; CHANGE 2 Chloramine Evacuator Draw Points, as shown on the plan, to instead be 4 -12” diameter flanged connections, evenly spaced along the length of Item 1A.

Item No 5.63 M150a HVAC DUCTWORK ALT.BID PLANS-AREA A

Plan #1 HVAC DUCWORK-UPPER LEVEL-AREA A; Clarification: round supply ductwork serving the pool area does not require insulation.

Item No 5.64 M404 - HVAC DETAILS

Detail 10 TYPICAL CURB DETAIL FOR IXISTING ROOF WITH EPDM ROOFING; CHANGE the note “OPENING BY G.C.” to instead read OPENING BY H.C.

ADD Detail 15 per attached Supplemental Drawing SD-M7

Item No 5.65 PS401 PLUMBING SITE DETAILS

EXCAVATION & BACKFILL NOTES, ADD note 7 as follows: 7. REFER TO THE CIVIL DRAWINGS FOR TRENCH SEALING

REQUIREMENTS FOR ALL TRENCHES PASSING THROUGH EXPANSIVE SHALE. SEE GEOTECHNICAL REPORT FOR LOCATIONS OF EXPANSIVE MATERIAL AND COORDINATE ALL EXCAVATION OPERATIONS PRIOR TO THE START OF WORK.


Item No 5.66 PD100, PD101, PD102 PLUMBING DEMO PLANS

CHANGE Drawings per attached Supplemental Drawing SD-P20, SD-P21 and SD-P22

GENERAL DEMOLITION NOTES; ADD note 3 as follows: 3. ANY EXISTING FIXTURES OR PIPING THAT INTERFERES WITH NEW WORK, EVEN IF NOT SPECIFICALLY INDICATED ON THIS DRAWING WILL BE OWNED BY THE CONTRACTOR TO BE REMOVED OR RELOCATED.

DEMOLITION NOTES; ADD note 22 as follows: 22. REMOVE ALL PLUMBING-RELATED FIXTURES AND PIPING IN THE

EXISTING KITCHEN.

Item No 5.67 P111 PLUMBING – GROUND FLOOR PLAN – AREA B

CHANGE Drawing per attached Supplemental Drawings SD-P19 and SD-P23

Item No 5.68 P301 PLUMBING ENLARGED PLANS

Enlarged Plan 2; CHANGE per attached Supplemental Drawing SD-P24

Item No 5.69 P302 PLUMBING ENLARGED PLANS

Enlarged Plan 3; CHANGE per attached Supplemental Drawing SD-P25

Item No 5.70 ES101 ELECTRICAL SITE PLAN

Electrical Note 10; ADD the following clairificatin to note: … UNDER THE ALTERNATE BID THE ELECTRICAL CONTRAACTR SHALL TRENCH, BACKFILL, AND PROVIDE 4” CONDUIT FROM THE RELOCATED TRANSFORMER LOCATON TO THE EXISTING TRANSFORMER LOCATION AT THE DISTRIUCT OFFICE.

Item No 5.71 E121. LIGHTING – FIRST FLOOR PAN – AREA B

Include 14 lighting fixtures, installation and wiring: Type F45. Exact location of the fixtues in Corridor B102 shall be determined by Architect during construction..


Item No 5.72 E131 LIGHTING – SECOND FLOOR PAN – AREA B

B108 Upper Vestibule; CHANGE lighting as follows:. Omit one of the three hanging pendant fixtures type F34B shown on plan and provide one

(1) 71” diameter pendant type F34A, and one (1) 24” diameter pendant type F34C.

Fixtures shall be supplied with a blue or red inner band. Color of each fixture determined by Architect at time of fixture submittal.

Architect will determine exact mounting location and suspension height of each pendant fixture in the space. Contractor shall arrange an on-site meeting with Architect before installation.

Wire fixtures on the branch circuit shown serving the original pendants.

Provide a switch and a 20amp generator transfer device (detailed on drawing E401) to switch two F24B’ and one F34C. Use normal circuit SEH1-11 for the normal control for the generator transfer device.

Item No 5.73 E134 LIGHTING – SECOND FLOOR PAN – AREA E

E200 Upper Stair Lobby; CHANGE lighting as follows: Omit one of the three hanging pendant fixtures type F34B shown on plan and provide and install

one (1) 71” diameter pendant type F34A, and one (1) 24” diameter pendant type F34C.

Fixtures shall be supplied with a blue or red inner band. Color of each fixture determined by the architect at time of fixture submittal.

The architect shall determine exact mounting location and suspension height of each pendant fixture in the space. Contractor shall arrange an on-site meeting with the architect before installation.


Provide a switch and a 20amp generator transfer device (detailed on drawing E401) to switch two F24B’ and one F34C. use normal circuit SEH1-11 for the normal control for the generator transfer device.

E103 Upper Reception; CHANGE the lighting as follows: Add to the one hanging pendant fixtures type F34A shown on plan, two (2) 40” diameter pendant

type F34B, and one (1) 24” diameter pendant type F34C.

Fixtures shall be supplied with a blue or red inner band. Color of each fixture determined by Architect at time of fixture submittal.

Architect will determine exact mounting location and suspension height of each pendant fixture in the space. Contractor shall arrange an on-site meeting with Architect before installation.



Item No 5.74 E501 ELECTRICAL RISERS

ADD feeder tags as follows:. Feeder to panel ‘SBH1” shall be tagged #9. Feeder to panel ‘FBH1’ shall be tagged #9. Feeder to panel ‘FBL6’ shall be tagged #8. Feeder to panel ‘NEG’ shall be tagged #3. Feeder to panel ‘FAL3’ shall be tagged #8. Feeder to panel ‘FBH2’ shall be tagged #9.

Item No 5.75 E503 LIGHTING AND MECHANICAL SCHEDULES

Lighting Fixture Schedule; CHANGE Fixture type F34A as follows:

# of Lamps: 18 Lamp Type: 18 watt PL

CHANGE Fixture type F34B as follows: # of Lamps: 9 Lamp Type: 18 watt PL

ADD Fixture type F34C as follows: Manuf: Beta-Calco Model: T15SD101AE # of Lamps: 6 Lamp Type: 18 watt PL Ballast Type: Electronic Description: 17.3” diameter, cable hung pendant fixture. Inner band color selected by the architect

ADD Fixture type F45 as follows: Manuf: Spectrum Model: SG8H-226T-EX-PR-SG-MOD # of Lamps: 2 Lamp Type: 26 watt PL Voltage: 277 v Description: 8” recessed down light. Fixture to have red open glass tier trim ring

ATTACHMENTS Project Manual Pages

Page 00 4116.04-3 08 7100 Attachment Door Hardware Sets (22pages)

Supplemental Drawings CS400 CS401 CS402 CS403 CS404 SDC-9 SDC-10

SDA-14 SDA-15 SDA-16 SDA-17 SDA-18

SDM-7

SDP-19 SDP-20 SDP-21 SDP-22 SDP-23 SDP-24 SDP-25

END OF DOCUMENT

PROPOSAL OF _____________________________________________________________ CONTRACT NO. 09033.000-4

(Name of Bidder)

ADDITIONS AND ALTERATIONS

LAUREL HIGHLANDS HIGH SCHOOL BID-FORM – ELECTRICAL CONSTRUCTION

LAUREL HIGHLANDS SCHOOL DISTRICT ADDENDUM 5 00 4116.01-3

UE-8: IMPORTED BACKFILL: Provide or omit one Cubic Yard of imported stone backfill, in place, for utility trench that passes beneath paved areas.

ADD OR DEDUCT____________________________________________________DOLLARS ($_______________)

. ADDENDA - In submitting this proposal, I have received and included in the Bid the following: Addendum No. Dated. Addendum No. Dated.

________1______ _____________________ _______________ _____________________

________2______ _____________________ _______________ _____________________

________3______ _____________________ _______________ _____________________

_______________ _____________________ _______________ _____________________

WHEN THE BIDDER IS AN INDIVIDUAL

If the Bidder is an individual trading under his own or a fictitious name, this Proposal must be signed by the individual Owner and his exact Post Office Address must be given. If one other than the Owner signs this Proposal, then a notarized certificate of authority signed by the Owner must accompany this Proposal.

____________________________________ _________________________________________(SEAL) Witness Bidder’s Signature Bidder’s Name Typed___________________________________________ Bidder’s Title___________________________________________ Address____________________________________________ Trading As___________________________________________ Fictitious Name

ADDITIONS AND ALTERATIONS DOOR HARDWARE SETS

LAUREL HIGHLANDS HIGH SCHOOL

LAUREL HIGHLANDS SCHOOL DISTRICT ADDENDUM 5 08 7100 APPENDIX –Page 1

08 7100 Attachment - DOOR HARDWARE SETS

Hardware Schedule

Set: 1.0

Doors: A104.2, A104.3, A104.4, A104d.1, A104d.2, A106.2, A106k.1, B000.2, B006.1, B108.2, B108.3, C002.1,

C104.1, D106.1, E104.1, E118.3, F007.1, F111.2, F112.1

2 Continuous Hinge MCK-14HD x LAR CL MK

1 Removable Mullion L980S PC SA

1 Mounting Kit 98-2579 SA

1 Exit Device 10 16 8504 862 US32D SA

1 Exit Device (rim, exit only) 10 16 8510 862 US32D SA

1 Cylinder 10 980C1 SA

1 Door Closer (surface w/stop arm) 351 CPS 351D 581-2 EN SA

1 Threshold 2005AT X LAR MSES10SS PE

2 Position Switch DPS-M-BK SU

Notes: WEATHERSTRIP IS BY DOOR MANUFACTURER.

Set: 2.0

Doors: C000.1, C001.1, C100.2, F006.1, F008.3







Set: 3.0

Doors: A002.1, A104.1, B000.1, B108.1, C103.4, D106.2, F126.1


1 Continuous Hinge MCK-14HD SER-12 x LAR CL MK




1 Exit Device 10 55 56 8504 862 US32D SA




1 ElectroLynx Harness QC-C*** (Length as Required) MK


1 Power Supply BPS-24 (Size as Required) SU


CARD READER BY TCC. PRESENTING AUTHORIZED CREDENTIAL TO CARD READER WILL UNLOCK

EXIT DEVICE ALLOWING ACCESS. EGRESS IS BY EXIT DEVICE. EMERGENCY ACCESS BY KEY.

DOOR HARDWARE SETS ADDITIONS AND ALTERATIONS


08 7100 APPENDIX –Page 2 ADDENDUM 5 LAUREL HIGHLANDS SCHOOL DISTRICT

Set: 4.0

Doors: C101.2, E104.2














CARD READER BY TCC. PRESENTING AUTHORIZED CREDENTIAL TO CARD READER WILL UNLOCK

EXIT DEVICE ALLOWING ACCESS. EGRESS IS BY EXIT DEVICE. EMERGENCY ACCESS BY KEY.

INTERCOM BY TCC CAN RELEASE EXIT DEVICE FROM REMOTE LOCATION.

Set: 5.0

Doors: E106.1







1 Gasketing S88D (Head & Jambs) PE


Set: 6.0

Doors: B116.3, C101.1


1 Removable Mullion 12-L980 PC SA



1 Exit Device (rim, exit only) 12 8510 862 US32D SA


2 Door Closer (surface w/stop arm) 351 CPS EN SA

2 Kickplate K1050 10" x 1" LDW 4BE US32D RO



1 Astragal S771C x Door Height PE





Set: 7.0

Doors: E106.2












Notes: CARD READER BY TCC. PRESENTING AUTHORIZED CREDENTIAL TO CARD READER WILL

UNLOCK EXIT DEVICE ALLOWING ACCESS. EGRESS IS BY EXIT DEVICE. EMERGENCY ACCESS BY

KEY.

Set: 8.0

Doors: D106.2A






2 Door Closer (surface w/stop arm) 351 PS EN SA






Set: 9.0

Doors: F110a.2


2 Flush Bolt 555/557 US26D RO

2 Storeroom Lock 10 8204 LNL US26D SA









Set: 10.0

Doors: F110f.2








Set: 11.0

Doors: B100.1, B100.2, B121.1



1 Mortise Deadlock MS1850S 1-1/2" BS 628 AD

2 Cylinder 10-42 US26D SA

2 Push Bar & Pull BF15847 US32D RO

2 Door Closer (surface) 351 OTB EN SA


Notes: WEATHERSTRIP IS BY DOOR MANUFACTURER. SIGNS STATING THAT COURTYARD IS TO

HAVE MAXIMUM OCCUPANCY OF 49 TO BE SUPPLIED.

Set: 12.0

Doors: A109.1


1 Exit Device 10 16 MD8610 106 x 862 US32D SA

1 Exit Device 10 16 MD8610 862 US32D SA








Set: 13.0

Doors: F003.1

6 Hinge TA2714 x NRP 4-1/2" x 4-1/2" US26D MK


2 Dust Proof Strike 570 US26D RO




2 Door Stop 409 US32D RO


1 Gasketing ACP112BL PE

2 Door Bottom 4131CRL PE


2 Silencer 608 RO

Set: 14.0

Doors: E103g.1

3 Hinge (heavy weight) T4A3786 NRP 4-1/2" x 4-1/2" US26D MK

1 Exit Device 10 12 8804 ETL US32D SA


1 Kickplate K1050 10" x 2 " LDW 4BE US32D RO


Set: 15.0

Doors: F121.1

6 Hinge (heavy weight) T4A3786 4-1/2" x 4-1/2" US26D MK

2 Surface Vert Rod Exit 12 NB8710 US32D SA



2 Electromagnetic Holder 998 689 RF



Notes: MAGNETIC HOLDER TO BE RELEASED BY FIRE ALARM ACTIVATION.

Set: 16.0

Doors: A105.10, A105.2, A105.3, A105.4, A105.5, A105.9, A201.2, D103.2, D103.3, D103.5, D103.6, D104.1,

D104.2, F102.2


2 Surface Vert Rod Exit 10 16 NB8713 ETL US32D SA

1 Door Closer (surface w/stop & holder) 351 PSH EN SA


2 Silencer 608 RO




Set: 17.0

Doors: A104g.1, A105.11, A105.12, C103.1, C103.2, C103.3, F102.1A, F110.1, F111.1







Set: 18.0

Doors: A104.7, A107.1, B007.1, C101.3, F113.1









Set: 19.0

Doors: C202.2







Set: 20.0

Doors: A105.7, A105.8, C102.2, D103.1, D103.4, E103d.1






3 Silencer 608 RO




Set: 21.0

Doors: C202.1






Set: 22.0

Doors: A002.2, A010.1, B002.1, B002.2, B108.4, B108.5, B108.6, B225.1



2 Exit Device 12 8815 ETL US32D SA






Set: 23.0

Doors: B116.1, B116.2, E105.1, E118.1, E118.2






1 Electro-Mechanical Closer 351 EHT-Push 351D EN SA




Notes: HOLDER CLOSER AND MAGNETIC HOLDER TO BE RELEASED BY FIRE ALARM ACTIVATION.

Set: 24.0

Doors: B218.1, E002.1, E201.1, E215.1






1 Electro-Mechanical Closer 351 EHT-Push 351D EN SA








Set: 25.0

Doors: A103.1, A105.1, A105.6, A124.1






Set: 26.0

Doors: A005.1, A006.1


1 Hinge (heavy weight) T4A3786 QC12 4-1/2" x 4-1/2" US26D MK


1 Exit Device 10 12 55 56 8804 862 US32D SA







1 ElectroLynx Harness QC-C1500P MK





KEY.

Set: 27.0

Doors: A106k.2

6 Hinge (heavy weight) T4A3386 x NRP 4-1/2" x 4-1/2" US32D MK

2 Exit Device CPC 10 12 NB8713 ETL US32D SA

2 Door Closer SRI 351 PS EN SA



Set: 28.0

Doors: E115.1

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






2 Silencer 608 RO




Set: 29.0

Doors: A016b.1, F005.1







2 Silencer 608 RO

Set: 30.0

Doors: A104a.1, A104b.1, A105a.1, A109h.2, A110d.1





2 Surface Overhead Holder/Stop 10-336 630 RF


2 Silencer 608 RO

Set: 31.0

Doors: A109g.1








2 Silencer 608 RO

Set: 32.0

Doors: A201.1

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK




2 Door Closer (surface) 351 O EN SA



2 Silencer 608 RO




Set: 33.0

Doors: A104c.1, C000b.1, C100.1







2 Silencer 608 RO

Set: 34.0

Doors: D203.1







2 Silencer 608 RO

Set: 35.0

Doors: F103.1

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK




1 Coordinator L1672 Wear Plates Black RO






Set: 36.0

Doors: A015.1, A018.1, F112a.1, F117.1





1 Coordinator L1672 Wear Plates Black RO

1 Mounting Bracket 1601AB Black RO








Set: 37.0

Doors: A001a.1, B009.1, B126.1, B129a.1, B206a.1, B207a.1, B212.1, B214a.1, B214b.1, B216a.1, B220a.1,

B221a.1, B223a.1, B224a.1, C102e.1, E103h.1, E108.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK




3 Silencer 608 RO

Set: 38.0

Doors: A009f.1, A011f.1, A012f.1, A013d.1, A014.1, A017.1, A109h.1, A116.1, A116.2, B115b.1, B115b.2,

B126.2, B212.2, E108.2, F110c.1, F110e.1, F115.1





3 Silencer 608 RO

Set: 39.0

Doors: B208.1

4 Hinge TA2714 4-1/2" x 4-1/2" US26D MK




3 Silencer 608 RO

Set: 40.0

Doors: A104f.1, C001c.1, F100b.1, F100b.2





3 Silencer 608 RO

Set: 41.0

Doors: A003.1, A114a.1, D103a.1, D103a.2, E115.2, E205.1, E212.1, E213.1, F110a.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





3 Silencer 608 RO




Set: 42.0

Doors: A104e.1, B004.1, B004.2, B005.1, B101.1, B107.1, C100a.1, D101.1, D101.2, D102.1, D201a.1, E117.1,

E200.1, F110f.1






3 Silencer 608 RO

Set: 43.0

Doors: B106.1, B129.1, B215a.1






3 Silencer 608 RO

Set: 44.0

Doors: F105.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






Set: 45.0

Doors: A008a.1, B003.1, B006.2, E001.1, F006.3, F008.1










Set: 46.0

Doors: A009b.1, A011a.1, A012b.1, A013a.1, A106d.1, A106f.1, A114.1, A115.1, A123.2, B006a.1, B115a.1,

C102d.1, C202b.1, C202c.1, C202d.2, E103b.1, E103j.1, E103j.2, E103m.1, E103n.1, E103o.1, E103p.1, E103q.1,

E103r.1, E103s.1, E103t.1, F110b.1, F110d.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Office Lock 10 8205 LNL US26D SA


1 Gasketing S773BL PE


1 Door Bottom 411APKL PE

1 Coat Hook RM802 US32D RO

Set: 47.0

Doors: A109b.1, A110a.1








Set: 48.0

Doors: A122.1, A123.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK









Set: 49.0

Doors: C202a.1












Set: 50.0

Doors: A110.2

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Store Door Lock 10 8226 LNL US26D SA







Set: 51.0

Doors: B122.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Classroom Lock 10 8237 LNL US26D SA






Set: 52.0

Doors: C000a.1







2 Silencer 608 RO

Set: 53.0

Doors: F001.1








1 Gasketing S88BL DOH X 2 PE






Set: 54.0

Doors: C102c.1, C102c.2, E103a.1, E103l.1, E103l.2

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Classroom Security Lock 10 8238 LNL US26D SA


3 Silencer 608 RO

Set: 55.0

Doors: A113.1, B105.1, C001a.2, C001b.2, D110.1, D110.2




3 Silencer 608 RO

Set: 56.0

Doors: B205.1




3 Silencer 608 RO

Set: 57.0

Doors: E103.3

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





3 Silencer 608 RO

Set: 58.0

Doors: G100.2


1 Electric Hinge TA2714-QC12 4-1/2" x 4-1/2" US26D MK

1 Integrated Card Reader Lock 10 H1-82271 LNL US26D SA



3 Silencer 608 RO



1 Push Button PB SU


Notes: PRESENTING AUTHORIZED CREDENTIAL TO INTERGAL LOCK CARD READER UNLOCKS

EXTERIOR TRIM ALLOWING ACCESS. INSIDE LEVER ALLOWS EGRESS AT ALL TIMES. INSIDE

LEVER HAS RX SWITCH. LATCHBOLT MONITORED.




Set: 59.0

Doors: F104.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






Set: 60.0

Doors: A004.1, A006a.1, A006a.2, A104.5, A104.6, C001a.1, C001b.1, E103k.1, F004.1







Set: 61.0

Doors: C200.1

8 Hinge TA2714 4-1/2" x 4-1/2" US26D MK







2 Silencer 608 RO

Set: 62.0

Doors: A202.1, A203.1, B110.1, B111.1, B114.1, B115.1, B118.1, B119.1, B120.1, B128.1, B130.1, B131.1,

B206.1, B207.1, B209.1, B210.1, B215.1, B216.1, B219.1, B220.1, B221.1, B223.1, B224.1, E110.1, E111.1,

E112.1, E113.1, E114.1, E119.1, E120.1, E207.1, E208.1, E209.1, E210.1, E211.1, E216.1, E217.1, E218.1,

E219.1, E220.1, E221.1, F100.1, F101.1




3 Silencer 608 RO

Set: 63.0

Doors: D200.1

4 Hinge TA2714 4-1/2" x 4-1/2" US26D MK



3 Silencer 608 RO




Set: 64.0

Doors: B214.1, D201.1, D202.1




3 Silencer 608 RO

Set: 65.0

Doors: B112.1, B113.1, C000.2, C001.2, D109.1, D111.1, E103c.3, F118.1, F119.1, F120.1, F122.1, F123.1, F124.1






Set: 66.0

Doors: B200.1, B201.1, B202.1, B203.1






Set: 67.0

Doors: C003.1, E203.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Hotel Lock 10 50 8250 LNL US26D SA






Set: 68.0

Doors: A106c.1, A114b.1, B123.1, B124.1, C102a.1, E103f.1, E103v.1, F106.1, F107.1


1 Hotel Lock 10 50 8250 LNL US26D SA








Set: 69.0

Doors: A009c.1, A011b.1, A012c.1, A013b.1, A106g.1, A121.1, B128a.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Privacy Set 49 8265 LNL US26D SA


3 Silencer 608 RO


Set: 70.0

Doors: A009.1, A011.1, A012.1, A013.1


1 Electric Hinge (heavy weight) T4A3786-QC12 4-1/2" x 4-1/2" US26D MK












Set: 71.0

Doors: G100.1














Set: 72.0

Doors: C102b.1


1 Deadbolt 10 487 US26D SA

1 Push Plate 70C US32D-MS RO

1 Pull Plate 110x70C US32D-MS RO




3 Silencer 608 RO

Set: 73.0

Doors: B011a.1, B110a.1, B125.1, B127.1, B211.1, B213.1, E107a.1, E109a.1, E204a.1, E206a.1


1 Deadbolt 10 487 US26D SA

1 Push Plate 70C US32D-MS RO

1 Pull Plate 110x70C US32D-MS RO



3 Silencer 608 RO

Set: 74.0

Doors: A005.2, A104d.3, A104d.4, F126.2


2 Push Bar & Pull BF15847 US32D RO





Set: 75.0

Doors: A119.1, A120.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Passage Set 8215 ALP US32D SA





Set: 76.0

Doors: B128.2, E103c.2

1 Sliding Door Hdwe HF2/100A/4 PE

2 Knob 841 US26D RO




Set: 77.0

Doors: E103.1





3 Silencer 608 RO

Set: 78.0

Doors: A106l.1, A106m.1




1 Storeroom Lock 10 28 10G04 LL US26D SA



2 Silencer 608 RO

Set: 79.0

Doors: A101.1, A101a.1, A101b.1


1 Storeroom Lock 10 28 10G04 LL US26D SA



Set: 80.0

Doors: A106e.1, A106h.1





Set: 81.0

Doors: A109e.1, A109f.1, A110b.1, A110c.1, C202d.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Passage Set 8215 LNL US26D SA


1 Gasketing 332CR PE






Set: 82.0

Doors: C200.2, C201.1, E103c.1

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






Set: 83.0

Doors: A109c.1, A109c.2


1 Store Door Lock 10 8226 LNL US26D SA






Set: 84.0

Doors: F110f.3

1 Hardware Hardware by Door Manufacturer OT

Set: 85.0

Doors: B106.2, B106.3, C100.3, C102.3, C102.4, C102.5, C102.6, D103a.3, D103a.4, D103a.5, F006.2, F008.2

1 Hardware Hardware by Door Manufacturer OT

Set: 86.0

Doors: G110.1

1 Electric Strike 9600-12/24D-LBM 2004M 2005M 630 HS




Notes: REUSE REMAINDER OF EXISTING HARDWARE. DOOR AND FRAME IS EXISTING.




Set: 87.0

Doors: F125.1


1 Electric Hinge (heavy weight) T4A3786-QC12 4-1/2" x 4-1/2" US26D MK

1 Exit Device 10 16 NB8710 US32D SA

1 Exit Device 10 55 56 NB8706 ETMI US32D SA



2 Silencer 608 RO






KEY.

Set: 88.0

Doors: A109.1A, A109.2, A110.1, C002.2, C102.1









Set: 89.0

Doors: MISC


1 Privacy Set 49 8265 LNL US26D SA



1 Software KW-SS1 SA

1 Electric Strike 1006-12/24-LBM 2004M 2005M 630 HS


1 Repair Kit QC-R001 MK

1 Crimp Tool QC-R003 MK

1 Test Unit WT1 SA


1 KEY BOX 1203 LU

END OF 087100 ATTACHMENT

RE

F.

1x -1" WD TRIM - FINISH SHALLMATCH ARCHITECTS SAMPLEBLKHD PAINTED P7 TYP

TB 3 TYPTB 2 TYPTB 4 TYP GCT 3 TYP

CT 1 TYP

CTB 1 TYP

P 1 TYP

6".

5' -

2".

3' -

0"1'

- 8"

TYP TILE GRAPHICREPEAT - SEE ELEV'SFOR LOCATIONS

ELEVATION- GRAPHIC SHALL BE MIRRORED ABOUT TYP

5' - 10" 2' - 6".

3' - 0"

2' - 0".

5' - 6" 5' - 6".

2' - 0".

5' - 3".

3' - 0"

3' - 0"

4' - 3".

2' - 3".3' - 1".

5' - 6".

5' - 0".

4' - 0".4' - 3".

4' - 9".

5' - 0".

3' - 3".2' - 8".

6' - 2".

4' - 3".3' - 4"

6' - 3".3' - 6 1/2" 3' - 6 1/2"

2' - 2" 2' - 2"

NOTE: WOOD TRIM SHALL BE FLUSH W/ TB PANELS TYP

EQ EQ

3' -

0".

2' -

2".

10"

1' -

4".

7"1'

- 6"

1' -

3"3'

- 0"

2' -

0".

1' -

6".

2' -

2"1'

- 9"

3' -

0"

1' -

1".

1' -

9".1

' - 0

".2'

- 9"

.3' -

0"

11"

2' -

1"5"

.1'

- 0"

.1'

- 0"

.1'

- 1"

.9"

3' - 0"

3' - 8".

1' -

6"

NOTE: REF DWG A721

WEIGHTSA005

FITNESSA006

CORRIDORA008

CORRIDORA007

1

1

1

11

1

TE-11

TE-11WAL

L M

OU

NTE

D M

IRR

OR

S TY

P- S

EE D

TL 6

/A35

4

21' -

2 1

/2"

7' - 11". 9' - 0"

WALL MOUNTED MIRRORS TYP- SEE DTL 6/A354

WALL MOUNTED MIRRORS TYP- SEE DTL 6/A354

9' - 0"

7' - 0". 7' - 0".

14' - 0"

13' -

8 1

/2"

NOTE: REF DWG A310

R G N A U GLE

589

7D

AE

SPOSIT

O8921

R A

AN

VLY

SN

N E P

REGISTE

RED

ARC

HIT

ECT RA

-

-

AI

Drawing Number

Proj

ect N

umbe

r

Date

P.D.

E. N

o.

CopyrightC

9/18/2012 2:38:34 PM

Laur

el H

ighl

ands

Hig

h S

choo

l

SDA-14

09/2

8/12

3675

Checker

0903

3.0

00

LAUR

EL H

IGHL

ANDS

SCH

OO

L DI

STRI

CT

RE

F D

WG

: A72

1, A

310

2012

ADD

ITIO

N A

ND

ALT

ERAT

ION

S

1/4" = 1'-0"2 CAFETERIA C103 S ELEV

1/8" = 1'-0"1 WEIGHTS A005 & FITNESS A006 MIRRORS

1/4"

1/4"

2"

1' -

3"

1/4"

1/4"

2"

1/4" TEMPEREDGLASS MIRRORSURFACE TYP - SEEELEV FOR JOINTLOCATIONS

OAK WOOD FRAME @ ALLEXPOSED EDGES OFCONTINUOUS MIRRORS -FINISH SHALL MATCHARCHITECTS SAMPLE TYP.ALL FASTENERS SHALL BECONCEALED TYP. SEE ELEVFOR LOCATIONS & DTLS

1/2" PLYWOODBACKER TYP

1 1/4"

1/4"

9"

2 1/

2"2

1/2"

2' -

0" A

FF5'

- 0"

.

FF

REF DWG A354

A7213

A34443

A34444

SDA-1643

SDA-1644

COMPUTER LABC200

COMPUTER LABC201

1 1

TE-3

6' - 0"- VDB7 6' - 0"- VDB7

TE-3

6' - 0"- VDB7

1

1

L-4 L-4L-112' - 0"-VDB7

L-2 L-2

L-8

L-8

6' -

0"- V

DB7

8

A353

Sim

9

A353

Sim

9

A353

Sim

8

A353

Sim

TYP FULL-HEIGHT PLASTIC LAMINATE COUNTERTOPSUPPORT - SEE DETAIL 11/A353. PROVIDE (1) PER TOP.

STEEL COUNTERTOPSUPPORTS TYP - PROVIDE(1) EVERY 3'-0" TYP

OSE-5 TYP

C-7 TYP C-7 TYP

5

5 TYP @ ALL INSTANCES WHERECOUNTERTOP KNEESPACEABUTTS THE WALLS

TYP @ ALL INSTANCESWHERE COUNTERTOPKNEESPACE ABUTTS THEWALLS

TYPTYP

SEE A132 FORDIMENSIONS TYP

SEE A132 FORDIMENSIONS TYP

REF DWG A332

OSE-5 TYP

OSE-5 TYP

R G N A U GLE

589

7D

AE

SPOSIT

O8921

R A

AN

VLY

SN

N E P

REGISTE

RED

ARC

HIT

ECT RA

-

-

AI

Drawing Number

Proj

ect N

umbe

r

Date

P.D.

E. N

o.

CopyrightC

9/21/2012 4:11:58 PM

Laur

el H

ighl

ands

Hig

h S

choo

l

SDA-15

09/1

8/12

3675

Checker

0903

3.0

00

LAUR

EL H

IGHL

ANDS

SCH

OO

L DI

STRI

CT

RE

F D

WG

: A33

2, A

354

2012

ADD

ITIO

N A

ND

ALT

ERAT

ION

S

1 1/2" = 1'-0"6

TYP MIRROR w/WOODFRAME DETAIL

1/8" = 1'-0"1 COMP RM C200 & C201

BC-O30.24.30

BC-236.30.30

BC-F116.30.30

BC-F316.30.30

BC-236.30.30

BC-F116.30.30

BC-F316.30.30

BC-236.30.30

BC-236.30.30

BC-236.30.30

3' - 1". 3' - 0"

2' -

6"

3' - 3".

2' -

6"

2' -

0"

C-7 TYP

BC-236.30.30

BC-F116.30.30

BC-F316.30.30

BC-O30.24.30

3' - 3"2' -

6"

C-7 TYP

FLOOR LINE

2' -

6"

1 1/4" PLASTIC LAMINATECOUNTERTOP W/ 3MM PVCEDGEBANDING UNO. SEE FINISHSCHEDULE & COLOR SCHEME FORCOLORS.

ELEC. OUTLET - COORD.LOCATION W/ E.C. TYP.

2 ' - 8"

OVERHANG

CL

GROMMETS TYP.SEE PLAN FORLOCATIONS

2' -

4 3/

4"1

1/4"

RUBBER BASE TYP @ ALLEXPOSED SIDES OF LOWWALL

1".

1' -

1 1/

32"

CL OUTLET

WIRE MANAGEMENT TRAY - SEE SPECS

8 7/8"

PROVIDE 1"W x 2"H FINISHEDCOUNTERTOP SUPPORT WHERECOUNTERTOPS MEET ROOMBOUNDING WALLS TYP. PROVIDEBLOCKING AS REQUIRED TYP

2 3/

8"

7"

1"OVERHANG

2' - 5 5/8"

6"

3"

10"

R 1'-1"

R 10"

R 1'-0"

NOTE: 1. PROVIDE (1) C-7 @ ALL OSE-5 LOCATIONS - COORD MOUNTING LOCATIONS W/ ARCHITECT PRIOR TO INSTALL TYP - SEE PLAN FOR LOCATIONS

H x

3"W

- W

IRE

MAN

AGEM

ENT

TRAY

CU

T-O

UT

@PL

ASTI

C L

AMIN

ATE

SUPP

OR

T PA

NEL

TYP

- ALL

EXP

OSE

DED

GES

@ C

UT-

OU

TSH

ALL

BE 3

MM

PVC

EDG

EBAN

DIN

G A

SSC

HED

ULE

D

PLASTIC LAMINATE - FULL HEIGHTSUPPORT PANEL W/ EDGES ASSHOWN 3' - 0" OC TYP UNO - SEEPLAN FOR LOCATIONS. ALLEXPOSED EDGES SHALL BE 3MMPVC EDGEBANDING TYP ASSCHEDULED. COORD WIREMANAGEMENT TRAY CUT-OUT ASSHOWN TYP - SEE FINISH SCHED &COLOR SCHEME FOR COLORS.

SET POINT OF ARC @ PANELS TYP

REF DWG: A353

1/4" OAK WOOD VENEER ON 1/2"PLYWOOD @ EXPOSED SURFACES TYPUNO - FINISH SHALL MATCHARCHITECTS SAMPLE. PROVIDEFINISHED PANEL @ EXPOSED SIDES TYP

4' - 0"- VDB6

A344

Sim 38

A344

Sim 38

A344

Sim 38

REF DWG: A320 & A320a

R G N A U GLE

589

7D

AE

SPOSIT

O8921

R A

AN

VLY

SN

N E P

REGISTE

RED

ARC

HIT

ECT RA

-

-

AI

Drawing Number

Proj

ect N

umbe

r

Date

P.D.

E. N

o.

CopyrightC

9/21/2012 4:12:06 PM

Laur

el H

ighl

ands

Hig

h S

choo

l

SDA-16

09/2

0/12

3675

Checker

0903

3.0

00

LAUR

EL H

IGHL

ANDS

SCH

OO

L DI

STRI

CT

RE

F D

WG

: A32

0, A

320a

, A34

4, A

353

2012

ADD

ITIO

N A

ND

ALT

ERAT

ION

S

1/4" = 1'-0"43 COMPUTER LAB C200 MILLWORK ELEV 1

1/4" = 1'-0"44 COMPUTER LAB C201 MILLLWORK ELEV 1

3/4" = 1'-0"11 SECTION @ COMPUTER LAB MILLWORK - FULL HEIGHT PL SUPPORTS

1/8" = 1'-0"1 NURSE A118 EAST ELEV

$$

KITCHENC102

CORRIDORC101

JAN CLC100a

LEVEL 2 ALTERATIONSPER 2009 IEBC - 3,204 SF

NEW CONSTRUCTION951 SF

32

4

12 HOUR RATED BUILDINGSEPARATION WALLUL# U419 AND UL# U905

2 HOUR RATED BUILDINGSEPARATION WALLUL# U419 AND UL# U905

90 MINUTE RATED DOOR

R G N A U G L E

58 97

DA

ESP

OSIT

O8921

R A

AN

VLY

SN

N E P

REGISTE

RED

ARC

HIT

ECT RA

-

-

AI

Drawing Number

Proj

ect N

umbe

r

Date

P.D.

E. N

o.

CopyrightC

9/21/2012 10:26:09AM

La

ure

l Hig

hlan

ds

Hig

h S

choo

l

SDA-17

09/2

8/12

Checker

0903

3.0

00

RE

F D

WG

: CS

101

& C

S10

1.1

LAUR

EL H

IGHL

ANDS

SCH

OO

L DI

STRI

CT

2012

3675

ADD

ITIO

N A

ND

ALT

ERAT

ION

S

1" = 20'-0"1 FIRE BARRIER AT KITCHEN

MC-127 1/2 x 855/8 x 19 1/4

MC-127 1/2 x 855/8 x 19 1/4

MC-227 1/2 x 855/8 x 29 1/4

MC-227 1/2 x 855/8 x 29 1/4

MC-427 1/2 x 855/8 x 29 1/4

1' - 10".

10' -

0"

4' -

0"

4' - 0" 4' - 0" 4' - 0" 4' - 0" 4' - 0" 4' - 0" 4' - 0" 4' - 0"2' - 0" 2' - 0"

OF WALL

39 TYP 22

A354

Sim

MC-1427 1/2 x 391/4 x 85 5/8

INSTRUMENTSTORAGE

A109h

A109

h.2

W11a

W5

W1b

W4d W4d

2' - 10 7/16"

1' -

7 1/

4"

REF DWG: A120 & A120aA343

10

A34320

A34321

A34324A3

43 23

SDA-1810

INSTRUMENTSTORAGE

A109h

1

REF DWG: A320 & A320a

R G N A U GLE

589

7D

AE

SPOSIT

O8921

R A

AN

VLY

SN

N E P

REGISTE

RED

ARC

HIT

ECT RA

-

-

AI

Drawing Number

Proj

ect N

umbe

r

Date

P.D.

E. N

o.

CopyrightC

9/21/2012 4:12:14 PM

Laur

el H

ighl

ands

Hig

h S

choo

l

SDA-18

09/2

1/12

3675

Checker

0903

3.0

00

LAUR

EL H

IGHL

ANDS

SCH

OO

L DI

STRI

CT

RE

F D

WG

: A12

0, A

120a

, A32

0, A

320a

, A34

3

2012

ADD

ITIO

N A

ND

ALT

ERAT

ION

S

1/4" = 1'-0"10 BAND CLASSROOM A109 - N ELEV

1/8" = 1'-0"1 INSTRUMENT STORAGE A109h REVISION

1/8" = 1'-0"2

INSTRUMENT STORAGEA109h CASEWORKRELOCATION

mes

Typewritten Text

The district office abatement is part of the Alternate Bid AA-1 only. These three windows shall be removed by the ACC. This will be clarified in Addendum 5.

mes

Typewritten Text

The windows at the north wall of E226 shall be removed by the ACC. The AD102 demolition plan will be modified by Addendum 5. Note 8 shall remain as stated on the bid documents. The ACC is responsible for review of the abatement survey report and including the removal of these components whether indicated on the drawings or not.

mes

Typewritten Text

Refer to the abatement report prepared by PSI and provided as additional information to bidders and hosted on Printscapes project plan room.

mes

Typewritten Text

The abatement legend should be removed from this drawing. It is not accurate. We will remove this from the drawing via addendum. . The hatching shown on the stair towers and pool hallway are not related to the abatement scope of work. These are floor material patterns that should be disregarded. I'll clarify this via addendum.

Page 1 of 1

Address301 North Mercer Street

New Castle, PA 16101

ContactPhone 724.652.5507

Fax 724.652-0751

www.EcklesGroup.com

PRE-BID REQUEST FOR INFORMATION

Project: LHSD – HS Add’s & Alt’s Date:

EAE Project No.: 09033.000To: Mark Scheller, PM/Architect

[email protected]

Contract No.: 09033.000 – _____CC: [email protected]

Contract Type:(circle one)

GC HC PC EC ACCTCC FSEC

EAERedirect to:

From: Date:

Company Name: E-mail Address:

Contact Person: Telephone: Fax:

Ref: Section/Drawing No.

No. QUESTION

Signature: Date:

No. RESPONSE

Name:Company: Date:

2

F.A.R-04, Inc.

Brad Maffei

724-379-8741

[email protected]

724-379-8239

Spec 232000 1.13 Duct Liner

Does all round low pressure ductwork require duct liner or can it be wrapped?

Brad Maffei

9-18-12

jcm

Text Box

If the round duct is not flex, and is not shown with a dashed interior line(the symbol for lining), it can be wrapped when insulation is necessary.

Page 1 of 1




Fax 724.652-0751

www.EcklesGroup.com




[email protected]




EAERedirect to:

From: Date:




No. QUESTION

Signature: Date:

No. RESPONSE

Name:Company: Date:

2

F.A.R.-04, Inc.

Brad Maffei

[email protected]

724-379-8741

724-379-8239

Spec 232000 1.06 Chemistry Fume Hood

Spec calls for Chemistry fume duct to be welded stainless... Does this also apply to the Biology , Physics & Classroom fume hoods on the 2nd floor area B (typ-13)

Brad Maffei

9-18-12

jcm

Text Box

1.06 does not require welded ducts, it does require "sealed" seams, joints , and connections.

Page 1 of 1




Fax 724.652-0751

www.EcklesGroup.com




[email protected]




EAERedirect to:

From: Date:




No. QUESTION

Signature: Date:

No. RESPONSE

Name:Company: Date:

2

F.A.R.-04, INC.

Brad Maffei

[email protected]

724-379-8741 724-379-8239

9-18-12

Drawing M150

1. Does the POOL Contractor own the underfloor evacuation duct?

Brad Maffei

9-18-12

Pool Addition

2. At what point in the Evacuation duct system does it switch from the Pool Contractor to the HVAC Sheet Metal contractor?

jcm

Text Box

Ductwork shown on the HVAC drawings serving the "Evacuator" system is the responsibility of the HC. The description and location of the connections will be clarified by addendum.

jcm

Text Box

Detail # 13 on M404 shows partial reuse of an existing opening--this detail would apply with no new opening.

jcm

Text Box

We will create a new detail, similar to #13 on M404, to address this question.

mes

Typewritten Text

This will be addressed by the mechanical engineer on an upcoming addendum. Most likely Addendum 5, which will be posted next week. The bids are being extended to October 2nd so you should have time to incorporate the addendum next week into your estimates. Addendum 4 will go out this week extending the bids.

TLM

Typewritten Text

1. Refer to Spec Section 12 3200 - Attachment - Appendix A - CASEWORK SCHEDULE. These items are Stevens Industries Casework.

TLM

Typewritten Text

TLM

Typewritten Text

2. Item E-2 @ Band Classroom A109 & Music Classroom A110 @ Elev 9/A343 - Music Library see tag E-2 @ dwg A356 Casework Equipment Schedule.

TLM

Typewritten Text

TRICIA MONACO, INTERIOR DESIGNER

TLM

Typewritten Text

TLM

Typewritten Text

ECKLES ARCHITECTURE

TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

mes

Typewritten Text

This glass type will be clarified in an Addendum and added to the glazing specification via same addendum.

jmp

Typewritten Text

jmp

Typewritten Text

jmp

Typewritten Text

1

jmp

Typewritten Text

2

jmp

Typewritten Text

3

jmp

Typewritten Text

It is up to each Prime Contractor to determine what shift size

jmp

Typewritten Text

jmp

Typewritten Text

and/or number of shifts will be required to complete their work.

jmp

Typewritten Text

No, depending on the alternate(s) taken, this would this would

jmp

Typewritten Text

jmp

Typewritten Text

jmp

Typewritten Text

jmp

Typewritten Text

jmp

Typewritten Text

jmp

Typewritten Text

disrupt the entire site at one time.

jmp

Typewritten Text

jmp

Typewritten Text

This would add additional work to the summer phase. With the

jmp

Typewritten Text

bid extension we will be addressing the completion dates for Phase 1.

jmp

Typewritten Text

John Pappas

jmp

Typewritten Text

9/14/12

jmp

Typewritten Text

Eckles Construction Services, Inc.

TLM

Typewritten Text

1. To clarify, the Nurse Reception desk is a custom designed piece of millwork. The cabinetry utilized for the piece could be manufactured elements, but the overall design of the desk is not something that can be purchased from a shelf. It will need built.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

Tricia Monaco

TLM

Typewritten Text

TLM

Typewritten Text

Eckles Architecture

TLM

Typewritten Text

9-18-12

TLM

Typewritten Text

LAUREL HIGHLANDS HIGH SCHOOL OPEN RFIs

*RFI 1 1. Drawing CS404 If Alternate #G-2 is not accepted, what work will there be to perform from 8-10-2013 to 2-1-2014. Please advise. 8. Please advise how many sets of drawings and specs GC gets.

*RFI 3 1. Drawing AD101 and AD102 eight gang restrooms, E107,E109,D125,D127,B211,B213,E206,E204 and all other miscellaneous restrooms with ceramic tile. All areas call for new UGT. Do we remove infill, existing or going right over existing. FLOORS NOT WALLS!!!!

*RFI 4 7. Drawing AD102, Note 80, Remove Concrete Risers to level of floor structure. After review of the existing building drawings online, we were unable to determine if these risers are hollow underneath. Is any additional information available.

*RFI 7 7. Room D103B, Detail 6/A721 shows CTB1. Room Finish Schedule A006 calls for wood base. Please clarify. 8. Detail 17/A354, is blocking required behind wall pads. If so, please advise to size and location. 9. I am unable to locate where detail 7/A353 is required. Room numbers listed on the on the detail do not seem to coincide with the project. Please review and advise. 10. Room D201A, Drawing A133. What is height and type of low wall. Please review and advise.

*RFI 8 Just submitted on Friday 9/7/12.

mes

Typewritten Text

We understand that there will be a gap in the construction sequence the actual work needed to be constructed during that time will be evaluated during construction and/or following the acceptance of the alternates.

mes

Typewritten Text

The owner will provide (6) sets of construction documents to the prime contractors.

mes

Typewritten Text

Answer located

mes

Typewritten Text

Answer located

TLM

Typewritten Text

SEE RFI #7 RE-ISSUED WITH ADDENDA 5

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text


TLM

Typewritten Text


Page 1 of 2

Address 301 North Mercer Street


Contact Phone 724.652.5507

Fax 724.652-0751

www.EcklesGroup.com


Project: LHSD – HS Add’s & Alt’s Date: 9/4/12/12

EAE Project No.: 09033.000 To: Mark Scheller, PM/Architect [email protected]

Contract No.: 09033.000 – 000-01 CC: [email protected]

Contract Type: (circle one) GC EAE

Redirect to:

From: Date:

Company Name: Mucci Construction E-mail Address: [email protected]

Contact Person: Marco Mucci Telephone: 724-677-2875 Fax: 724-677-4711

Ref: Section/ Drawing No.

No. QUESTION

1. Alternate #2, Pool Addition, Drawing C1-02, per bid/Unit Cost UG-4b, include 1500 cys, store, rework, etc. Drawing C7-01 shows stockpile location and I have concerns for damages. Should we include this in the pricing?

2. Drawing C7-01. Please advise how I can determine Alt. 1, Alt. 2 and Base Bid requirements. The way it is shown on the structural and architectural drawings is clear but I am unable to determine on C7-01. Please review and advise.

3. Drawing C2-02, Scope/Camera existing pipe to remain, assess condition and replace if condition is substandard. Same drawings same line, remove or grout in place, example 15” storm sewer, scope/camera etc. Drawing CD1-02, Note D-7 remove – abandon existing line, cap portions that remain in place. I am guessing this is due to excavation. Which is it? Please review and advise.

4. Drawing CS300 Phase S1. Is access road per base bid or Alternate #1. Please advise.

5. Drawing C2-01 Detention Facility. There are 4 manholes on ends of detention chambers identified as UDF MH. There is a fifth circle that is not identified. Please advise.

6. Drawing C2-01 Rain Garden North Side. Note 18, Pipe to Remain Until Alternate 2 Buildout. What if alternate #2 is not accepted?

7. Room D103B, Detail 6/A721 shows CTB1. Room Finish Schedule A006 calls for wood base. Please clarify.

8. Detail 17/A354, is blocking required behind wall pads. If so, please advise to size and location.

9. I am unable to locate where detail 7/A353 is required. Room numbers listed on the on the detail do not seem to coincide with the project. Please review and advise.

10. Room D201A, Drawing A133. What is height and type of low wall. Please review and advise.

11. Drawing A360, Toilet Accessories, #6 Electric Hand Dryer. Are these to be furnished and installed by the GC? Please review and advise.

12. Drawing S001, Top Right Corner, references fireproofing, see architectural drawings. We are unable to locate any reference on the architectural drawings or find location designation in the specs. Please review and advise.

13. Specification Section 072100-3, 2.03 spray applied foam insulation. We are unable to locate this material on the drawings or find location designation in the specs. Please review and advise.

Page 2 of 2




Fax 724.652-0751

www.EcklesGroup.com

14. Drawing A361, Room E107 (Similar E206). It seems that some toilet accessory notations are missing. Please review and advise.

Signature: Date: No. RESPONSE Name: Company: Date:

mes

Typewritten Text

1. Yes, include pricing in your estimate to cover you for adequate means of protecting existing surfaces or replacing them once the work is complete. A general requirement for sitework will be to replace or repair affected areas to pre-construction conditions. 2. Additional information has been added to Drawing C7-01 for clarification. Refer to Addendum #2. 3. Refer to Addendum #2 Drawings SDC-6 and SDC-7 for clarification 4. The access road shall be constructed as part of Alternate Bid G-1 5. The "Underground Detention Facility" detail on Drawing C8-01 indicates that the 5 circles are to be 6' dia. standard manholes 6. If Alternate Bid G-2 is not accepted, the pipe shall remain as a permanent improvement 7. Detail 6/A721 is similiar in reference to the single VDB-14 elev as dimensioned & tagged on the west wall of Aud. Lobby D103b. Wood base as listed on Dwg A006 is correct. All of Auditorium D103 & Auditorium Lobby D103b shall have wood base as sched. 8. Detail 17/A354 references the heights of the wall padding. See PE-4 note designation on drawings A320. There will be an addenda to add these notes to A320a(alt) 9. This detail will be deleted from the project - does not apply. 10. Low wall @ D201A - Wood Cap shall be @ 3'-4"aff. 11. Electric hand dryer to be provided by GC. 12. Spray applied fire proofing is not required on this project. 13. Yes, accessories are not indicated which should be. We will clarify in Addendum.

Page 1 of 2




Fax 724.652-0751

www.EcklesGroup.com


Project: LHSD – HS Add’s & Alt’s Date: 9/7/12


Contract No.: 09033.000 – 000-01 CC: [email protected]

Contract Type: (circle one) GC EAE

Redirect to:

From: Date:

Company Name: Mucci Construction E-mail Address: [email protected]

Contact Person: Marco Mucci Telephone: 724-677-2875 Fax: 724-677-4711


No. QUESTION

1. Does unit costs #UG,7A,7B,7C and 7D also pertain to detention facilities? 2. Drawing C8-01 Rain garden-typical section detail:

A. Note 1, Rain Garden Alternate 1, which rain garden is this? And are two identical inlets required for the other rain garden?

B. Detail illustrates 18” pipe, unable to confirm layout, length, etc. C. Per Addendum 1, Unit Costs identify cubic yards in north and south rain garden.

Do these cubic yards include the 3’ excavation from the bottom of the ponding depth down?

D. For the piping inlets, gravel, construction soil mix, etc. go with storm work identified under Addendum 1 Drawing C2-01, C2-02.

3. Drawing C2-03 Hillside Excavation Northern East Side of new kitchen addition. Please advise if bench key ways are required and if so, does a detail exist?

4. Appliance 17 not on schedule 5. A360 scoreboards by GC? 6. What is the ceiling tile requirement in C102 and C102C? We are unable to locate

them on the reflected ceiling plan. 7. What is Acoustical Ceiling Tile Type #17 @ B003 & E001? Type #17 is not listed in

Spec Section 095113. 8. At A001, Wall Types W15 and W16. I am unable to locate any use of these on the

project. Please review and advise. 9. Specification Section 095113, Paragraph 2.05A. Please advise to the heights of

the following items: Axiom Classic Trim & Axiom Vector Inverted Trim. 10. Drawing A006, Room C001B, Note GR20, provide sliding curtain and track. Is this

to be the same as the cubicle curtains? Please review and advise. 11. Addendum #1, Sketch SDA-3. Please advise what product is required by the

notation E.F.M. 12. Detail 19/A354, I am unable to locate where this is required. Please review and

advise. 13. Specification Section 104400 and Details 1, 2 & 3 on A354. I am only able to

locate notation FEC-A throughout the drawings. I have found no notation of the fully recessed FEC or Defibrillator anywhere on the drawings. Are they required?

14. Drawing A320 calls for 3’x7’ mirrors in Rooms A109b, A109c, A109e, A109f and A110c. I am unable to determine if we are to follow detail 6/A354 or Specification Section 088300. Please review and advise.

mes

Typewritten Text

Not applicable

mes

Typewritten Text

Gym scoreboards existing to remain. Pool scoreboards by GC.

mes

Typewritten Text

Not all wall types on A001 are used on the project

mes

Typewritten Text

No, This will be provided

mes

Typewritten Text

See below

mes

Typewritten Text

See below

mes

Typewritten Text

See below

mes

Typewritten Text

See below

mes

Typewritten Text

See below

mes

Typewritten Text

Yes

TLM

Typewritten Text

- Please clarify

TLM

Typewritten Text

Ceiling type - @ C102 & C102c shall be ACT-Type 1, 8'-4"aff.

TLM

Typewritten Text

1hr Fire-Rated 2x4 ACT - Refer to Addenda 5

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

EFM - is Entrance Floor Mat - See Color Scheme for details of product

TLM

Typewritten Text

DWG A320 mirrors shall follow spec section 08 8300

Page 2 of 2




Fax 724.652-0751

www.EcklesGroup.com

15. Drawing A356, Natatorium Equipment Schedule, NE-5 (Shown on East Wall of Room A106), Scoreboard, See Pool Drawings. Drawing SP-1 Pool Plan and Equipment Layout indicates scoreboard on North Wall but provides no further information. Is the scoreboard owned as part of the GC contract?

Signature: Date: No. RESPONSE Name: Company: Date:

mes

Typewritten Text

1. The detention facilities fall outside of the PEM areas.

mes

Typewritten Text

13. The recessed FEC is specified if required for installation means. Location and quantity shall be governed by the code requirements. New difribulators are not required and the existing cabinets will be reused and/or relocated in the building.

mes

Typewritten Text

mes

Typewritten Text

mes

Typewritten Text

2A. Rain Garden RG-ALT-1 is on the north side of the High School; Rain Garden RG-S is on the south side of the Admin. Building. Two identical outlet structures are required for RG-ALT-1 only.

mes

Typewritten Text

2B. Refer to Sheets C2-01 and C2-02 for layout, length, etc. of 18” outlet pipe.

mes

Typewritten Text

3. Sheet G-2 “Fill Embankment Construction” shows locations and requirements for slope benching.

TLM

Typewritten Text

Scoreboard is owned by Pool Contractor

Address

301 North Mercer Street


www.EcklesGroup.com Contact

Phone 724.652.5507

Fax 724.652-0751


Project: LHSD – HS Add’s & Alt’s Date: August 29, 2012

EAE Project No.: 09033.000 To: Mark Scheller, PM/Architect

[email protected]

Contract No.: 09033.000 – CC: [email protected]

Contract Type: GC HC PC EC ACC (circle one) TCC FSEC

EAE Redirect to:

From: Date:

Company Name: Northeast Interior Systems, Inc.

E-mail Address: [email protected]

Contact Person: Neil DenBleyker Telephone: 315-622-3121 Ext. # 122 Fax: 315-622-3103


No.

QUESTION

06 4000/A007 1. Drawing A007 lists GR1 as granite wall caps that are required at low walls at all water cooler low wall

& A720 surrounds and at all low wall caps (typical). However detail 10a/A720 indicates that the low wall

surrounds at the water cooler locations are to be SS1, which is listed as Avonite solid surface

materials on drawing A007. Please clarify which material is required at the water cooler locations.

Signature: Date:

No. RESPONSE Name: Company: Date:

Page 1 of 1

http://www.ecklesgroup.com/

TLM

Text Box

The Granite - (G1) shall be provided @ all water cooler low wall surrounds - @ their CAPS. I will issue an addenda clarifying this note in detail 10a/A720.

TLM

Text Box

Tricia Monaco, Eckles Architecture

TLM

Text Box

9-7-12

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

12 3200/A007 1. For the epoxy resin countertops of this section, it indicates per Item 2.07.C.3. Color: As Scheduled.

However, no color is indicated on the Color Schedule, drawing A007, under any of the schemes listed.

Please clarify if manufacturer’s standard black epoxy resin will be acceptable.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

Epoxy Resin countertop color shall be - equal to Epoxy Products, color #09 Blue

TLM

Typewritten Text

TLM

Typewritten Text

Tricia Monaco, Interior Designer - Eckles Architecture

TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 & 1. On drawing A324 in room E103k, there are two visual display boards identified as VDB5C.

10 1100 / A324 & VDB5C does not exist on drawing A351. Please clarify the visual display boards required in this room.

A351

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

TLM

Typewritten Text

VDB5C - SHALL BE CHANGED TO VDB5

TLM

Typewritten Text

TRICIA MONACO, INTERIOR DESIGNER, ECKLES ARCHITECTURE

TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

12 3200/A331 & 1. Per the details 10 through 10b on A353, it indicates that there is a plastic laminate panel at the face of

A353 Of the chase for the typical teacher’s stations. Please clarify if we are to supply a plastic laminate

panel or a wood veneer panel at the face of the teacher’s stations in the rooms designated to

receive wood veneer casework.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

DETAILS 10-10b SHALL BE PLASTIC LAMINATE @ FACE OF THE TEACHER'S STATION CHASE AS DETAILED ON DWGS.

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

12 3200/A353 1. Details 10/A353 refers back to detail 2c/A323. This detail does not exist. Please clarify the proper

detail elevation number.

2. Detail 10b/A353 refers back to detail 2C/A352. This detail does not exist. Please clarify the proper

detail elevation number.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

1. & 2. SHOULD BE CHANGED TO REFER TO DETAIL 10a/A353.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

06 4000/A123 & 1. There appear to be countertops located behind the overhead coiling doors D103a.3 through D103a.5

A323 but are not elevated anywhere. Please provide elevations or clarify what section details we can use

for these countertops.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

Refer to elevation 16/A343 similar. Countertop shall be wall to wall - kneespace width shown in elev shall be wider @ Control room D103a.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

12 5651 / A332 1. There is a presentation station located in room # C202 that refers back to elevation 20/A325.

Drawing A325 does not exist. Please provide details for this presentation station.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

1. NOTE SHALL BE CHANGED TO REFERENCE - DETAIL 20 / A352.

TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 / A340 1. Detail 7/A340 indicates that there is ¼” finished plywood applied to the face of the low wall at the

front of the ADA seating platform in D103. Please clarify what finish is required on the back side of

this wall.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text

1. ALL EXPOSED SIDES OF THE LOW WALL SHALL HAVE 1/4" FINISHED PLYWOOD OVER GYP BD TYP W/ 1x 4" FINISHED WOOD TRIM AS SHOWN IN ELEV 32/A340 TYP.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 / A004a 1. Detail 15/A004a provides details for the finishes required at coiling shutters at wood counters.

However, I can not find reference to this detail at any of the “CS” door types on the door schedules

or any reference of this section through the coiling shutters on any of the floor plans. Please clarify

where this detail is to be used.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

1. @ DETAIL 15/A004a - SEE CONCESSION B106 CASEWORK, DOORS B106.2, B106.3, D103a.3, D103a.4, & D103a.5.

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 & 1. Note 1 at VDB6 states that there is to be wood trim provided at VDB6 units in Vestibule E104 and

10 1100 / a351 in Main Lobby B106. B106 is the Concession stand, and has no VDB6’s located in it. Also, the

Main Lobby B100 has no VDB6’s in it. Please clarify where these VDB6’s are located.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

TLM

Typewritten Text

1. REFERENCE IN NOTE TO MAIN LOBBY B106 SHALL BE CHANGED TO READ - CORRIDOR E106.

TLM

Typewritten Text

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

11 5314/A353 1. It appears that you have the room #’s switched for the single sided and double sided fume hoods at

dlevation 18/A352. There are (5) single sided fume hoods, tagged as SE-2 on floor plans on A331 and

(9) double sided fume hoods, tagged as SE-7 on floor plans on A331. Please clarify.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

1. NOTE WILL BE CHANGED TO SWITCH ROOM NUMBERS LISTED ON DTL 18/A352, AS TAGGED ON FLOOR PLAN DWGS.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751




[email protected]



EAE Redirect to:

From: Date:





No.

QUESTION

12 3200/A354 1. It appears that you have the details for the casework wardrobes and the closet interiors switched,

i.e. detail 11/A354 states “Typ Section @ Closet -1” which I believe should be the title for detail

13/A354, but shows the section view of a cabinet with shelves and clothes rod. Conversely,

Detail 13/A354 states “Typ Section @ Wardrobe” but shows wall mounted plastic laminate shelves

above a closet rod supported by a wall mounted bracket. Please clarify.

Signature: Date:


Page 1 of 1


TLM

Typewritten Text


TLM

Typewritten Text

9-17-12

TLM

Typewritten Text

1. SEE BELOW FOR CLARIFICATION OF LOCATIONS OF DETAILS 9-13 ON DRAWING A354. SHALL BE INCLUDED W/AN\ ADDENDA. - 9 & 9A are typically in the locker rooms - A009a, A011c, A012a, A013c, A106e, A106h, B202 - 10 are @ A109g and A110d (the note on dwgs referencing this dtl shall be changed to dtl 13/A354), B129(wall mounted) - 11 are @ B115b, F110c, F110e - 12 are @ B128b - 13 are @ A109g and A110d (see above remarks)

TLM

Typewritten Text

Address

301 North Mercer S treet New Castle, PA 16 1 0 1

www.EcklesGroup.com Contact Phone 7 24. 6 5 2. 55 0 7 Fax 724.652- 07 5 1






EAE Redirect to:

From: Date:





No.

QUESTION

11 5314 / A341 1. The specification for the fume hoods list only an Air Master Systems Model # 36MAF fume hood which & A352 is a single sided fume hood. Detail 18/A354 indicates this model number along with a model EH-211-36, which is a double sided fume hood. Please provide specifications for the double sided

fume hoods.

2. Item 2.04.A.2. indicates that the fume hoods on this project are 48 inches wide. The model numbers

Listed on drawing A352 and listed in 2.04.A.1 are for 36” wide fume hoods. (Note – on drawing A341,

the hoods are drawn at 34” wide – which are not an available size). Please clarify that 36” wide hoods

are required for this project.

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. See Addenda 5 for Double-Sided FumeHood Spec

TLM

Typewritten Text

TLM

Typewritten Text

2. 36" wide hoods are to be provided - Single-Sided(SE-2) & Double-Sided(SE-7) as tagged on Floorplan Dwgs. This will be clarified in Addenda 5.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

Address








EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 / A300 1. The specification states that all wood for transparent finish, item 2.01.B, is to be white maple except Series drawings as otherwise scheduled or noted on drawings. There are several pieces of trim that are required on the drawings, i.e. wood trim @ VDB5A units in the corridors, that by specification are to be

maple, but are in the same areas as red oak items, i.e. display cases, etc. Please clarify the species

required for these trim pieces. (Note – the specifications also call for wood plywood for transparent

finish to be red oak, i.e. Auditorium stage front, ADA seating low wall, bulkhead @ proscenium, etc.)

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. Wood Trim shall be RED OAK. All wood for the project shall be RED OAK not MAPLE.

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

Address








EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A343 1. In room #’s A109 and A109h there are music instrument storage cabinets, designated as MC-1, MC-2, MC-7, etc. These music instrument storage cabinets appear to be open cabinets with no doors. However, on the casework schedule included at the end of the casework specification, you list

Three different model Stevens model numbers, one being an open cabinet, the second having solid

laminate doors, and the third having wire grille doors. Please clarify if what is type of cabinet

is required for these units, no doors, solid doors, or wire grille doors as there is a cost differential

for each type of cabinet.

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. ALL cabinets listed with an MC tag, shall receive WIRE GRILLE DOORS w/lock hasps for the owner to supply the locks. This will be clarified through Addenda 5.

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

Address




Project: LHSD – HS Add’s & Alt’s Date: September 12, 2012




EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A343 1. In room # A109h there is a model MC-42 at the very right hand side of elevation 20. This MC-42, per the specification, is a Stevens model 55167, which is a full height angled corner cabinet with a Lazy Susan type assembly for flag storage. However, the cabinet drawn appears to be a 60” wide

straight cabinet at 39” deep. Please clarify what cabinet is required at this location.

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. MC-42 shall be CHANGED to be equal to Stevens Model No. 56204 - Mobile Triple Bass Rack. This will be clarified in Addenda 5.

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

TLM

Typewritten Text

Address








EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A356 1. On drawing A356 there is an item, C-10 on the Casework Equipment schedule, that just says Folder Rack without any Manufacturer, Model Number, or Description listed. Please clarify what needs to be supplied for this item.

Signature: Date:


Page 1 of 1

TLM

Stamp

TLM

Typewritten Text

1. This will be in Addenda 5

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

Address








EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A356, 1. On drawing SDA-11 at the Circulation Desk, elevation 38, there is a reference to E1 which appears A353, &SDA-11 To be a keyboard tray. However, there is no reference to E1 on the Casework Equipment Schedule On drawing A356. Please clarify that this should be C-1 in lieu of E1. (Note – this also occurs at the

section detail 1 on drawing A353 for the Reception Desks).

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. This tag should read C-1. This will be changed in Addenda 5.

TLM

Typewritten Text

TLM

Typewritten Text

TRICIA MONACO, Eckles Architecture

TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

Address








EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A353 1. There appears to be casework at the computer lab millwork on one side of the 36” H low wall at section & A356 9/A353 in room #’s C200 and C201. However, no elevations have been provided for these two locations. Please provide elevations for this casework.

2. I am not able to locate Section detail 11/A353 anywhere. Is this detail used? If so, please advise

Where it can be found. Also, per note 1, it indicates that we are to supply an E12 at each OSE-5

Location. There is no description of E12 in the specification or on the Casework Equipment Schedule

On drawing A356. Please clarify what an E12 is.

Signature: Date:


Page 1 of 1

TLM

Typewritten Text

1. These will be given in and SDA dwg in Addenda 5. 2. Part A: This detail shall apply to Comp. C200 & C201 2 back rows of countertop kneespace for support. These will be located & called out on an SDA dwg in Addenda 5. Part B: I'm not sure where Note 1 you are referencing? This will be clarified on SDA dwg in Addenda 5: @ Comp C200 & C201 - @ every OSE-5 location provide (1) C-7. There is no E-12 on the project.

TLM

Typewritten Text


TLM

Typewritten Text

9-19-12

TLM

Typewritten Text

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751






EAE Redirect to:

From: Date:





No.

QUESTION

12 3200 / A007 1. For Scheme # 3, there is an edge band color EB2, Iridescent Green, that is required for countertops where PL3 is to be used. Scheme 1 also lists PL3 at countertops in certain rooms, however, no edge band color is listed for these tops. It has come to my attention that the edge band color EB2 in Scheme 3 is not readily available in the size required for the countertop thickness required for this Project. Please verify if this color is truly required for this project and if so, is it also required for Scheme 1 in rooms where PL3 countertops are used.

Signature: Date:

No. RESPONSE 1. EB2 shall be required @ PL3 countertops as specified.

2. 2. CLARIFICATION - @ E103, E103k, C202, G100, G102 all casework countertops edgebanding s shall be 1 ¼” eased oak wood @ all exposed edges unless noted as SS1 countertops. Miter all

corners typ. Wood finish shall be selected by architect. Refer to detail 1/A353 for wood edgebanding profile detail. 3. Scheme 1 @ PL3 countertops EB1 shall be provided. These will be addressed in Addenda 5. Name: Tricia Monaco Company: Eckles Architecture Date: 9-21-12

Page 1 of 1


mailto:[email protected]


Address




Phone 724.652.5507

Fax 724.652-0751






EAE Redirect to:

From: Date:





No.

QUESTION

11 3112 / A356 1. There is a commercial ice maker, tagged as APP-12, on Appliance Equipment on drawing A356 that I am not able to locate on any floor plan or elevation. Please clarify if this appliance is required for this project?

Signature: Date:


Page 1 of 1




TLM

Typewritten Text

1. This is located @ ICE A008a.

TLM

Typewritten Text

TLM

Typewritten Text


TLM

Typewritten Text

9-21-12

TLM

Typewritten Text

Address




Phone 724.652.5507

Fax 724.652-0751






EAE Redirect to:

From: Date:





No.

QUESTION

06 4000 / A120a 1. Per detail 10/A720, there are 3-Form panels above the low walls that terminate at the ceiling at the & A420a, A720 water fountain locations. One of these water fountains occurs at the pool per floor plans on A120a. However, per the reflected ceiling plan, the pool ceiling terminates at the structure above, with no height Indicated. Please clarify if these low walls are to receive 3-Form panels above, or are we to just provide a granite wall cap at these low walls.

Signature: Date:


Page 1 of 1




TLM

Typewritten Text

1. No 3-Form panels shall be provided above the low walls @ Electric Water Coolers in Pool A106. This will be clarified in Addenda.

TLM

Typewritten Text


TLM

Typewritten Text

9-21-12

TLM

Typewritten Text

Maureen

Typewritten Text

09/20/20012

Maureen

Typewritten Text

Pitt Electric, Inc.

Maureen

Typewritten Text

Gary J. Jacovino

Maureen

Typewritten Text

[email protected]

Maureen

Typewritten Text

412-488-0302

Maureen

Typewritten Text

412-488-8225

Maureen

Typewritten Text

09/20/12

Maureen

Typewritten Text

Gary J. Jacovino

Maureen

Typewritten Text

Dwg ES151

Maureen

Typewritten Text

Please clarify the bitumious paving transition detail on Dwg ES151. It appears that if the EC digs a 1-ft wide ditch through the asphalt, we would be required to repave 5-ft on each side of the ditch for a total of 11-ft wide of paving..? There is approximately 700' to 900' needed. This would be extremely expensive.

Maureen

Typewritten Text

Maureen

Typewritten Text

Maureen

Typewritten Text

Maureen

Oval

TJB

Text Box

Paving shall be bid as shown on detail.

kspacie

Typewritten Text

09/18/2012

TJB

Text Box

Drawing E404 denotes correct configuration of connector strip outlets.

kspacie

Typewritten Text

09/18/2012

TJB

Text Box

Rigging is included in the general contract. Electrical contract responsible for the stage electrics and attachment to the General's rigging.

kspacie

Typewritten Text

09/18/2012

TJB

Text Box

Referring to 260961.2.16-2.16-A and G. PARNels are to be supplied.

jrial

Oval

jrial

Typewritten Text

06

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

28 23 00The Access control specs calls out for integration between Vicon and S2. Is there a quanity of cameras that

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

needs to intergrated or does all camera need to be integrated?

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

28 13 02Since the GC is providing electric strikes on this project is there a count on how many strikes are being provided?

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

Horizon Information Services

JWillman

Typewritten Text

JWillman

Typewritten Text

JWillman

Typewritten Text

John Willman

JWillman

Typewritten Text

[email protected]

JWillman

Typewritten Text

412-487-7071

JWillman

Typewritten Text

412-487-7072

TJB

Text Box

All cameras are to be integrated to the the S2 system. Refer to the architectural drawings and door hardware schedule for all electronic hardware being supplied under the general contract.

TJB

Text Box

Timothy J. Brown, Eckles Group

TJB

Text Box

9/17/2012

TLM

Typewritten Text

1. One VDB13 shall be installed @ Special Ed Resource B202.

TLM

Typewritten Text

TLM

Typewritten Text

Tricia Monaco

TLM

Typewritten Text

Eckles Architecture

TLM

Typewritten Text

9-19-12

3 The Owner will be responsible for moving their own items.

2. See Addenda dwg - SDA-1, issued with Addenda 1.

1. Disregard - these will be eliminated via Addenda.

TRICIA MONACO, Eckles Architecture 9-19-12

September 11, 2012

01

Yarborough Development, Inc. [email protected]. Lee Totty 412-673-7620 412-673-7318

1) Please advise what the H-1/8/9 marks mean that are shown on the door schedule under the remarks column. 2) Please clarify detail 2/A320 ramps at Gym Entry - they are removed on the demolition drawing but the detail is unclear as to what work is to be done. 3) Who is responsible for removing Owner related materials on the east side of the maintenance bldg., should alternate 1 be accepted?

R. Lee Totty 9/11/12

1. Gym A105 - WEST Elev is to be similar of EAST Elev of Gym - (Note will be added to addendum to address this.)- Drawing A320 & A320a - Tag 1/A720 shall be ADDED @ the WEST wall.- Drawing A720 - WEST elev 8/A720 shall be omitted- Drawing A320 & A320a - NORTH elev - tag 2/A720 similar shall be ADDED - Text shown shall be omitted @ SOUTH wall, Horizontal

stripe shall be continuous***THESE WERE ADDRESSED IN ADDENDA 3.

2. Pool A106 - EAST elev shall be similar to WEST elev shown. Text shall be omitted, Horizontal stripe shall be continuous.- Drawing A320a - Tag 4/A720 similar shall be ADDED @ EAST wall. Text shown shall be omitted @ EAST wall, Horizontal stripe shall be

continuous. - Drawing A320a - Tag 3/A720 similar shall be ADDED @ NORTH wall.

3. AXIOM VECTOR, CLASSIC TRIM STRAIGHT - 6" CHANNEL - shall be specified.Axiom trim shall be located @ the following rooms/Ceiling Types: Engineering C000 - Type 13, information Tech - Type 13,Upper Band Classroom A109 - Type 6, Upper Music Classroom A110 - Type 6, Upper Lobby A104g - Type 7, Vestibule B108 - Type 7

4. Acoustical Ceiling Type 17 is 1hr-rated ACT. Shall be addressed in Addenda 5.5. See Tile Backing Panels - Section 2.03. Should be Durock, not Gyp Bd.

September 11, 2012

01


1) Per the finish schedule, there are wood fiber panels on all 4 walls in the Gymnasium, Rm. # 105. On the elevation drwg. A720, only east, west and south elevations are shown. Please clarify panels lay out at the north wall. 2) The drwg. A720/3,4 shows wood fiber panels lay out at the south and west swimming pool wall. Are there wood fiber wall panels at the north and east swimming pool walls? If there are, please show panels lay out. 3) Please clarify locations of axiom trim as specified in the section 095113/2.05/A. There is none noted in the drawings. Also, please clarify axiom trim type and size. 4) Please clarify what is acoustical ceiling tile type 17 noted in the drwgs., ex. rm. E001 on the drwg. A412. There is no acoustical ceiling type in the 095113 spec. section. 5) Per the spec. section 092116/3.08/a.5, impact resistant board is req. at corridors up to 8' AFF. Per add. # 1, Durock is req. under ceramic tile at all locations. Please clarify what board is to be applied under ceramic tile on drywall partitions at corridors - Durock or High impact board?


No, a more detailed schedule will not be developed until the project is awardedand specific construction activities and durations can be provided by thesuccessful Prime Contractors. The start date for this Phase is shown asJune 10, 2013 to allow the Owner time to vacate these spaces.

John PappasEckles Construction Services 9/14/12

September 12, 2012

01


For the work in Phase 5, is there any outline schedule to show how the work this phase is to be completed in the time alotted? You have 50+ rooms/cafeteria and 4 sets of rest rooms all to be done in a 60 calendar day period.
