Added and Changed Features for Installation Manual and ...bucsesz.uw.hu/file/TD_816es1232_install kieg1.pdf · Digital Super Hybrid System KX-TD816CE KX-TD1232CE Added and Changed

Digital Super Hybrid SystemKX-TD816CEKX-TD1232CE

Added and Changed Features for

Installation Manual and Programming Tables

Please read this manual first and then the Installation Manual.In this manual, the last letter “CE” of each model number is omitted.

2

Warning:Static sensitive devices are used. To protect printed circuit boards from staticelectricity, do not touch connectors indicated below. To discharge body static,touch ground or wear a grounding strap.

Warning

REMOTE

SYSTEM INTERCONNECTION

DISA

DOORPHONE

Warning : Static sensitive connectors

3

Table of Contents

Added FeaturesSection 1.4, OptionsPay Tone Card (KX-TD189) ............................................................................................... 62-ISDN S0 Line Unit (KX-TD280)..................................................................................... 6Section 2.4, Installation of Optional Cards and Units2-ISDN S0 Line Unit Connection ....................................................................................... 6Installing Expansion Unit (KX-TD280).............................................................................. 7Pay Tone Card (KX-TD189) Installation ............................................................................ 9Section 3, FeaturesBudget Management............................................................................................................ 12Calling Line Identification Restriction (CLIR) ................................................................... 12Charge Fee Reference.......................................................................................................... 13CO Incoming Call Information Display.............................................................................. 14CO Incoming Call Information Log.................................................................................... 15Direct Dialing In (DDI)....................................................................................................... 16Emergency Call ................................................................................................................... 17HOTEL APPLICATION ..................................................................................................... 18

Check-In / Check-Out ...................................................................................................... 18Timed Reminder, Remote (Wake-Up Call) ...................................................................... 19

SMDR for Timed Reminder ................................................................................................ 20Section 4, System Programming[009] Emergency Dial Number Set .................................................................................... 21[010] Budget Management................................................................................................. 22[011] Charge Margin Rate .................................................................................................. 23[120] Charge Display Selection.......................................................................................... 24[121] Assignment of Denomination ................................................................................... 25[122] Charge Verification Assignment............................................................................... 26[123] Charge Verification ID Code Set .............................................................................. 27[124] Hotel Application...................................................................................................... 28[125] User Password .......................................................................................................... 29[216] Message Waiting Ring Interval Time ....................................................................... 30[217] Timed Reminder Alarm Repeat Times ..................................................................... 31[218] Timed Reminder Alarm Interval Time ..................................................................... 32[417] CO Line Name Assignment...................................................................................... 33[418] ISDN Line Number Assignment .............................................................................. 34[419] ISDN Outgoing CLIR Service Assignment.............................................................. 35[420] ISDN DDI Service Assignment................................................................................ 36[423] Pay-Tone Assignment ............................................................................................... 37[610] ISDN DDI Number / Extension Number Transformation........................................ 38[611] ISDN DDI Number / Floating Number Transformation........................................... 39

4

Table of Contents

[815] SMDR Output Mode................................................................................................. 40[990] System Additional Information, Fields (27) through (35)........................................ 41

Changed FeaturesSection 3, FeaturesDirect Inward System Access (DISA)................................................................................. 44Display, Call Information .................................................................................................... 44, 46Do Not Disturb (DND)........................................................................................................ 44DSS Console (KX-T7240 / KX-T7040).............................................................................. 44Message Waiting ................................................................................................................. 44, 47Operator............................................................................................................................... 44Station Message Detail Recording (SMDR) ....................................................................... 44, 48 Section 4, System Programming[001] System Speed Dialing Number Set........................................................................... 44, 52[002] System Speed Dialing Name Set .............................................................................. 44, 54[100] Flexible Numbering .................................................................................................. 44[109] Expansion Unit Type ................................................................................................ 45, 55[211] Dial Start Time.......................................................................................................... 45[412] Pause Time................................................................................................................ 45[413] Flash Time ................................................................................................................ 45[601] Class of Service ........................................................................................................ 45, 57[990] System Additional Information, Fields (17) and (26) .............................................. 45

Deleted FeaturesSection 3, FeaturesCaller ID .............................................................................................................................. 59Calling Party Control (CPC) Signal Detection.................................................................... 59Section 4, System Programming[110] Caller ID Code Set .................................................................................................... 59[111] Caller ID Name Set ................................................................................................... 59[405] CPC Signal Detection Incoming Set......................................................................... 59[406] Caller ID Assignment ............................................................................................... 59[415] CPC Signal Detection Outgoing Set ......................................................................... 59

Programming Tables ........................................................................... 60

5

Added Features

6

1.4 Options

Supports the Pay Tone service of the central office. While havinga conversation with an outside party, your central office generatesthe pay tone so that the counting for fee starts for the call.

Pay Tone Card (KX-TD189)

One KX-TD280 can be installed per system.

2-ISDN S0 Line Unit (KX-TD280)

D1232D1232DIGITAL SUPER HYBRID SYSTEM

PanasonicPanasonic

2 ISDN S0 linescan be added.

2.4 Installation of Optional Cards and Units

2-ISDN S0 Line Unit Connection

To add two ISDN S0 lines, use the optional 2-ISDN S0 Line Unit(KX-TD280). This unit can be installed in any of the expansionareas provided on the front of the main unit.

The following procedures can be used to install the 2-ISDN S0 LineUnit (KX-TD280). System programming is required for unitlocation identification.Default KX-TD816: bottom = 4-CO Line Unit,

top = 8-Station Line UnitKX-TD1232: bottom = 4-CO Line Unit,

middle and top = 8-Station Line Unit

PanasonicPanasonic


2 ISDN S0 linescan be added.

7

Installing Expansion Unit (KX-TD280)

PanasonicPanasonic


2. Connect the cabinet cord to theconnector in the main unit firmly.

1. Loosen two screws on the cover plate.Insert fingers into the slits to remove thecover plate.

Note Any of the cover plates can beremoved, as needed.

Note Be sure to fix the inside screw to themain unit, or the unit may not workproperly.

3. Hook the cabinet to the main unit andslide the cabinet to the left until it issecured.

SlitSlit

4. Loosen the outside screw and slide thecover to the right.


PanasonicPanasonic

PanasonicPanasonic

D1232D1232DEGITAL SUPER HYBRID SYSTEM

PanasonicPanasonic


Outside screw

5. Secure the inside screw (included) to fixthe cabinet to the main unit.

PanasonicPanasonic


Inside screw

6. Prepare the required plugs. Two 4-pinplugs are included in KX-TD280 toconnect four CO lines.

TB

TA

RA

RB

8


PanasonicPanasonic

Notes • The KX-TD1232 is illustrated as amain unit.

• If two or three expansion units areinstalled, cut the cabinet covers on thelower cabinets to allow the cords fromthe upper cabinet to go down throughthe cabinet covers. To protect thecords, smooth the cut edges.

8. Tie all of the cords into a bundle. Ifother cords are exposed in the uppercabinets, tie them also.

9. Close the cabinet cover and securethe outside screw.

10. Cover the cords with the cord holder(included).

11. Fix the cords to the wall as shown sothat the front cover can be opened.

Programming ReferencesSection 4, System Programming,[109] Expansion Unit Type

Cord holder

Cut here


PanasonicPanasonicPanasonic

2CO w/PFT

2CO

ISDNPort No.1

ISDNPort No.2

TBTA

RARB

To Terminal Board or ModularJacks from the Central Office

7. Insert the plug into a jack on the unit.Connect an earth wire to the earth terminalon the extension expansion unit.

Installing Expansion Unit (KX-TD280)

9

Pay Tone Card (KX-TD189) Installation

(1) Installing to the Initial CO Line Card1. Loosen eight screws to open the inside cover of the main unit.

Note If any cards, units, or cords are installed in the main unit, removethem beforehand.

2. Attach the Pay Tone Card(s) (KX-TD189) to the CO Line Card,with the spacers (Accessary included).One Pay Tone Card for KX-TD816, and up to two Pay Tone Cardsfor KX-TD1232 can be installed to the initial CO Line Card.

KX-TD816

CO3,4

CO1,2OPJP

B

OPJ

PC

OPJ

PD

OPJP

A

J200

J200

Cut here

Pay Tone Card

Inside cover

CO LineCard

OPJPA - D

CO Line Card

10

3. Put the inside cover back on the main unit and secure the screws.4. If you do not cut the wire of the J200 in pay-tone card, the detected

mode is 16 KHz. If you cut the wire of the J200 in Pay Tone Card(Open Mode), the detected mode is 12 KHz.

5. After installing the Pay Tone Card, if you hear a noise of the pay-tone signal, cut the option Jumper Wires, OPJPA through OPJPHcorresponds to CO1 through CO8 in the CO Card. (OPJPA corresponds to CO1, OPJPB to CO2, OPJPC to CO3, OPJPD to CO4,

OPJPE to CO5, OPJPF to CO6, OPJPG to CO7, and OPJPH to CO8.)

— When you install the Pay Tone Card A, you will detect the pay-tone signal from

CO1 - CO4, and cut the corresponding option Jumper Wires, if needed.

— When you install the Pay Tone Card B, you will detect the pay-tone signal from

CO5 - CO8, and cut the corresponding option Jumper Wires, if needed.


KX-TD1232

J200

J200

CO7,8

CO5,6

CO3,4

CO1,2OPJP

B

OPJ

PC

OPJ

PD

OPJP

E O

PJPF

OP

JPG

OP

JPH

OPJP

A

B

A

Cut here

Pay Tone Card

Inside cover

CO Line Card

OPJPA ~ H

CO Line Card

11

(2) Installing to the Optional 4-CO Line Unit

The following procedures must be done before installing the 4-COLine Unit (KX-TD180) to the main unit.

Note To install the 4-CO Line Unit to the main unit, refer to Section 2.4.4“Installing Expansion Unit (KX-TD170 / KX-TD180)” in theInstallation Manual.

Programming ReferencesSection 4, System Programming,[423] Pay-Tone Assignment

Feature References Section 3, Features,Display, Call Information (in this manual)HOTEL APPLICATION (in this manual)

1. Loosen five screws located on the rear of the 4-CO Line Unit.2. Remove the back plate and take out the P-board.3. Attach the Pay Tone Card to the P-board, fitting the connectors.4. Put the P-board back into the cabinet and fix the rear plate with

the five screws.5. If you do not cut the wire of the J200 in Pay Tone Card, the

detected mode is 16 KHz. If you cut the wire of the J200 in pay-tone card (Open Mode), the detected mode is 12 KHz.


4CO@

DIGITAL SUPER HYBRID SYSTEM

J200 Cut here

J200

P-board

back plate

BC 3 Features

12

Budget Management

Description Limits the telephone usage to a pre-assigned amount. Forexample, the limit may be the amount deposited at check-in of ahotel. If the pre-assigned limit is reached, the extension usercannot make further calls until he/she receives authorization fromthe operator.

Conditions None

Programming ReferencesSection 4, System Programming,[010] Budget Management

Feature References Section 3, Features,HOTEL APPLICATION

Operation References Not applicable.

Calling Line Identification Restriction (CLIR)

Description Allows the extension user to restrict the presentation of the callingparty’s number to the called party when making a call. This is oneof the ISDN services.

Conditions If the presentation is enabled, the called party can check the callingparty’s number before the called party is answered it (Calling LineIdentification Presentation, CLIP).

Programming ReferencesSection 4, System Programming,[418] ISDN Line Number Assignment[419] ISDN Outgoing CLIR Service Assignment

Feature References None


3 Features C

13

Charge Fee Reference

Description Allows the pre-assigned display telephone user to view, clearcharges and print out the data by SMDR. Charges are displayedper extension, CO line, account code, or the total of each can bereferred to.

Conditions • The allowed extension is determined by System Programming.• The verification ID is required to perform this feature.• A maximum of 99999 Meter can be collected. The existing call is not

referred.• It is programmable to select the first display, Meter or Charge by

System Programming. This can be switched manually at eachextension.

• Exchange rate between Meter or Charge is assigned by StationProgramming.

Programming ReferencesSection 4, System Programming,[120] Charge Display Selection[122] Charge Verification Assignment[123] Charge Verification ID Code SetStation Programming .......................................................User Manual, Charge Fee Reference


Operation References Station Programming,—User Manual Charge Fee Reference

C 3 Features

14

CO Incoming Call Information Display

Description Provides the display proprietary telephone user with a preset COline name if an incoming outside call is received. If the CO name isnot assigned and the CO line is an ISDN line provided with CLIP(Calling Line Identification Presentation) feature, shows thecaller’s telephone number and name on the display.

Conditions • It is required to name CO lines by system programming.• With the CLIP feature, the ISDN line informs the system of the caller’s

telephone number only. To display the name, the system compares theinformed number with the System Speed Dialling Numbers stored inprogram [001] and if a match is found, decides the caller’s name byusing the System Speed Dialing Names stored in program [002].

• The CO line name display has precedence on the Operator’s telephone.• The display DPT (KX-T7230 or KX-T7235) user can record the

information of the call received by CLIP feature (CO Incoming CallInformation Log feature).

Connection ReferencesSection 2, Installation,2.4 Installation of Optional Cards and Units (in this manual)

Programming ReferencesSection 4, System Programming,[001] System Speed Dialing Number Set[002] System Speed Dialing Name Set[417] CO Line Name Assignment[418] ISDN Line Number Assignment[419] ISDN Outgoing CLIR Service Assignment

Feature References Section 3, Features,CO Incoming Call Information Log

Operation Reference DPT Features, —User Manual CO Incoming Call Information Display

3 Features C

15

CO Incoming Call Information Log

Description If the display digital proprietary telephone (KX-T7230 or KX-T7235) user cannot answer a call, the telephone automaticallyrecords the caller’s telephone number, name and the time. The usercan call back the caller by checking the call log. This is available ifsuch a telephone receives incoming outside calls from the ISDNline provided with the CLIP (Calling Line IdentificationPresentation) feature. A maximum of 15 calls per telephone canbe logged.

Conditions • The call log is registered at the time DPT finishes ringing. If a call isdirected to multiple DPTs, the call log is registered at the DPT that hasthe smallest jack number of the ringing DPTs.

• Transferred call information is also recorded.• If the DPT is in Call Forwarding – No Answer or IRNA is activated,

the call log is registered at the original DPT but not at the destinationDPT unless the destination party answers the call and record itmanually.

• When the information area is full (i.e. more than 15 calls), the user cancontrol the log mode at his / her extension (CO Incoming CallInformation Log Mode). If the user sets this mode, new CO incomingcall information is retained but old data is discarded. If the user cancelsthis mode, new CO incoming call information is not entered in the unit.To set or cancel the mode, a corresponding feature number is used.

• The telephone user can lock the display of the unit so that COincoming call information is not shown on the display. A lock code isrequired to set or cancel this feature. Operator can cancel the lock incase the user forgets the lock code.


Programming ReferencesSection 4, System Programming,[001] System Speed Dialing Number Set[002] System Speed Dialing Name Set[100] Flexible Numbering, CO incoming call information log mode/CO

incoming call information log lock[417] CO Line Name Assignment[418] ISDN Line Number Assignment[419] ISDN Outgoing CLIR Service Assignment

D 3 Features

16

Feature References Section 3, Features,CO Incoming Call Information Display

Operation Reference DPT Features, —User Manual CO Incoming Call Information Log Lock

CO Incoming Call Information Log ModeOperator Service Features,CO Incoming Call Information Log Lock Clear

Direct Dialing In (DDI)

Description Provides an automatic direction of an incoming ISDN S0 line callto a specific extension. This requires a DDI number informedfrom the ISDN network. The DDI number is converted to aspecific extension number by using a pre-programmed conversiontable.

Explanation1. An incoming call from the ISDN network reaches your DSHS

(Digital Super Hybrid System).The ISDN network informs DSHS of the DDI number.

2. DSHS converts the DDI number to an extension number anddirects the call to the extension.

Conditions • The DDI service can be enabled or disabled on a CO line basis.• After the extension number is determined, the system operates the call

in the same way as the DIL 1:1 operation. • If a DDI number cannot be converted to an extension number, the call

is put to IRNA destination.


Extension200

(DDI: 111)

201(DDI: 112)

202(DDI: 113)

DSHS

ISDN

555-4112

DDI number

{

NetworkExternaltelephone

3 Features E

17

Programming ReferencesSection 4, System Programming,[420] ISDN DDI Service Assignment[610] ISDN DDI Number / Extension Number Transformation[990] System Additional Information, Fields (31) and (32)



Emergency Call

Description Allows the extension user to dial out a pre-assigned emergencynumber without seizing a CO line.

Conditions • Emergency numbers are allowed even in the following cases:• in Account Code – Verified mode• in any toll restriction level• after the pre-assigned charge limit is reached • in Electronic Station Lockout

• A maximum of eight emergency numbers are assignable. An extensionnumber can be stored as an emergency number to call service deskwith 1 digit for HOTEL APPLICATION.

• [009] Emergency Dial Number Set — Emergency dial location number(1-8) corresponds to [100] Flexible Numbering — No. 55-62.

<Example> If you want to assign “110” as an emergency call, you need assign thefollowing programming:

— Assign [100] Flexible Numbering, Feature Number “55,”Emergency call 1:110

— Assign [009] Emergency Dial Number Set, Location Number “1,”

1:9110

Programming ReferencesSection 4, System Programming,[009] Emergency Dial Number Set[100] Flexible Numbering, Emergency call 1 through 8


Operation References DPT Features, SLT Features;—User Manual Emergency Call

H 3 Features

18

HOTEL APPLICATION

Description Allows the operator to handle the front/operator services such ascheck-in / check-out, timed reminder (wake-up call). This operationis applicable to only the operator extension with a KX-T7235.

Check-In / Check-Out

Description Allows the operator to operate the check-in / check-out service.This feature can control the usage of an outside call by switchingthe Class of Service between primary and secondary, and countand print out the telephone charge and the other charges (such asmini-bar charges).

Conditions • Hotel application must be enabled by System Programming. • When the check-in is assigned, the Class of Service is set to the

primary one and the charge counter will be cleared. When the check-out is assigned, the Class of Service is set to secondary one and thetotal telephone charge and the other charge will be displayed andprinted out.

• There are two types of check-out mode, ready or not ready (cleaned upor not). The check-out operation by the operator changes the roomstatus from check-in to check-out (not ready) mode. Changing fromcheck-out (not ready) to check-out (ready) mode can be executed eitherfrom the room or by the operator.

• The telephone charge can be added to the surcharge according to thepre-assigned margin rate.

• When Hotel Application is enabled, all extension is set to the primaryCOS. After completing a confirmation of check-in and check-out, theextension is set to the secondary COS.

• If the operator uses the paired DSS console, the operator can refer tothe room status on the DSS console while the display of paired KX-TD7235 is in HOTEL menu. The lightening patterns of DSS buttonand room status are shown below:

• It is possible to give a header to the printed bill such as the hotel’sname or greeting or to assign the starting location of output data with apersonal computer.

• A new page is started for each print-out.• It is possible to limit telephone usage to a pre-assigned amount by

System Programming.

Room Status Check-inCheck-out (not ready)Check-out (ready)

Lighting PatternRed onRed flashOff

3 Features H

19

Programming ReferencesSection 4, System Programming,[010] Budget Management [011] Charge Margin Rate [100] Flexible Numbering, Check-out ready [124] Hotel Application[423] Pay-Tone Assignment[601] Class of Service

Feature References Section 3, Features,Budget Management Charge Fee Reference

Operation References Operator Service Features, —User Manual Hotel Application

Timed Reminder, Remote (Wake-Up Call)

Description Allows the operator to remotely set, cancel and confirm the wake-up call for an extension.

Conditions • When either an operator or the extension sets a new time, the pre-settime is cleared.

• The Alert button on Operator 1’s extension turns red if the guest doesnot respond to the alarm ringing. The Alert button can also be used toconfirm the not responded room number or to call back the room.

• The Alert button can be assigned to a flexible CO button on Operator1’s extension only.

• SMDR records the detailed Timed Reminder information and prints itout automatically when the Timed Reminder starts and it is notanswered. You can disable the printout by System Programming.

Programming ReferencesSection 4, System Programming,[100] Flexible Numbering, Timed reminder, remote[217] Timed Reminder Alarm Repeat Times[218] Timed Reminder Alarm Interval Time[990] System Additional Information, Field (36)

Feature References Section 3, Features,SMDR for Timed Reminder

Operation References Operator Service Features,—User Manual Hotel Application

S 3 Features

20

SMDR for Timed Reminder

Description Station Message Detail Recording (SMDR) automatically recordsdetailed Timed Reminder information. It is printed out when theTimed Reminder starts and the alarm is not answered. To enablethe printout, refer to the program [990] “System AdditionalInformation, Field (36),” which allows you to print out thefollowing records:

• Date• Time• Extension number• Start / No Answer

An example of a printed Timed Reminder record:

Conditions Connect a printer provided with an EIA (RS-232C) interface to the EIA(RS-232C) connector located on the main unit.

Connection ReferencesSection 2, Installation,2.3.10 Printer Connection

Programming ReferencesSection 4, System Programming,[801] SMDR Format [806]–[807] EIA (RS-232C) Parameters[990] System Additional Information, Field (36)

Feature References Section 3, Features,Station Message Detail Recording (SMDR)Timed ReminderTimed Reminder, Remote (Wake-Up Call)


Date Time Ext CO Dial Number Duration Acc code CD

06/24/96 10:03AM 103 Reminder / Start

06/24/96 10:04AM 103 Reminder / No Answer

21

4.2 Manager ProgrammingEmergency Dial Number Set

009

Description Assigns emergency call numbers.

Selection • Emergency dial location number: 1 through 8• Telephone number: 16 digits (max.)

Default All locations – Not stored

Programming 1. Enter 009.

Display:Emergency Call

2. Press NEXT.

Display:Emergency NO?→

3. Enter an emergency dial location number.

To enter emergency number 1, you can also press NEXT.Display example: 1:9110

4. Enter a telephone number.

To delete the current entry, press CLEAR.To change the current entry, press CLEAR and the new number.

5. Press STORE.

6. To program another emergency dial number, press NEXT orPREV, or SELECT and the desired emergency diallocation number.

7. Repeat steps 4 through 6.

8. Press END.

Conditions • There is a maximum of eight emergency call numbers. Each numberhas a maximum of 16 digits, consisting of 0 through 9, , #, F (Flash),P (Pause) and – (hyphen).

• No restriction is applied to emergency call numbers.• For outside calls, enter a line access code (9, 81 through 88) before the

phone number.• Emergency dial location number (1-8) corresponds to [100] Flexible

Numbering — No. 55-62.

Feature References Section 3, Features,Emergency Call

22

4.2 Manager ProgrammingBudget Management

010

Description Assigns the charge limitation of a call on an extension basis.

Selection • Jack number:KX-TD816 – 01 through 16, (-1 / -2),KX-TD1232 – 01 through 64, (-1 / -2), ( =all jacks, -1 = first part, -2 = second part)

• Charge limitation : 0 through 59999

Default All jacks – 0


Display:Charge Limit

2. Press NEXT.

Display:Jack NO?→

3. Enter a jack number.

To enter jack number 01, you can also press NEXT.

Display example: #01–1: 0

4. Enter a charge limitation.

To delete the charge limitation, press CLEAR.

5. Press STORE.

6. To program another jack, press NEXT or PREV, orSELECT and the desired jack number.

7. Press END.

Conditions • If the charge limitation is set to “0,” no restriction is applied.• To assign all jack number to one selection, press the key in step 3.

In this case, the display shows the contents programmed for Jack 01.

Feature References Section 3, Features,Budget Management

23

4.2 Manager ProgrammingCharge Margin Rate

011

Description Assigns the margin rate of a telephone charge.

Selection Margin (%): 0 through 999

Default 0%


Display: Charge Margin

2. Press NEXT.

Display: Margin: 0%

3. Enter a charge margin rate.

To delete the charge limitation, press CLEAR.

4. Press STORE.

5. Press END.

Conditions Telephone charge = Real charge x ( )

The telephone charge will be printed out when checking out.

Feature References Section 3, Features,HOTEL APPLICATION – Check-In / Check-Out

100 + rate

100

24

4.3 System ProgrammingCharge Display Selection

120

Description Assigns the initial display format of charge fee on a displaytelephone.

Selection in Meter / in Charge

Default in Meter


Display: Charge Meter

2. Press NEXT.

Display example: in Meter

3. Keep pressing SELECT until the desired selection isdisplayed.

4. Press STORE.

5. Press END.

Conditions• This programming is only effective when you select for charge (SMDR

Output) by Program [815] “SMDR Output Mode.” • This programming will also determine the print-out format of the

charge fee reference.

Feature References Section 3, Features,Charge Fee ReferenceDisplay, Call InformationStation Message Detail Recording (SMDR)

Description Assigns the Denomination required for your country.

Selection 2 characters (Max.)

Default none


Display: Denomination

2. Press NEXT.

Display example: Denomi.: KC

3. Enter a 0-9, , #, SELECT, CLEAR, or none.

To change the current entry, press CLEAR and the new characters.

To enter characters, see Section 4.1.3 “Entering Characters.”

4. Press STORE.

5. Press END.

Conditions • If more than two digits are entered, they are ignored.

Feature References Section 3, Features,Display, Call Information

25

4.3 System ProgrammingAssignment of Denomination

121

26

4.3 System ProgrammingCharge Verification Assignment

122

Description Assigns the extension which is allowed to refer or clear for the callinformation on the extension, CO line, account code, and the total.

Selection • Jack number: KX-TD816 – 01 through 16, ( =all jacks)

KX-TD1232 – 01 through 64, ( =all jacks)• Enable / Disable

Default All jacks – Enable


Display:Charge Refer Ext

2. Press NEXT.

Display:Jack NO?→



Display example: #01:Enable


5. Press STORE.


7. Press END.

Conditions • In the case of KX-TD1232, Jack numbers 01 through 32 are for theMaster System and 33 through 64 are for the slave.

• To assign all jack numbers to one selection, press the key in step 3.In this case, the display shows the contents programmed for Jack 01.

Feature Reference Section 3, Features,Charge Fee Reference

27

4.3 System ProgrammingCharge Verification ID Code Set

123

Description Assigns an ID code required to refer the charge information.

Selection 4 digits (0000 through 9999)

Default 1234


Display: Charge ID Code

2. Press NEXT.

Display example: Code: 1234

3. Enter an ID code.

To delete the current entry, press CLEAR.

4. Press STORE.

5. Press END.

Conditions None

Feature Reference Section 3, Features,Charge Fee Reference

28

4.3 System ProgrammingHotel Application

124

Description Assigns whether the hotel application is enabled or disabled.

Selection Disable / Enable

Default Disable


Display: Hotel Apply Asn

2. Press NEXT.

Display example: Hotel : Disable


4. Press STORE.

5. Press END.

Conditions If “Enable” is selected, the menu “Hotel” is displayed on the operatorextension’s KX-T7235 and the “Check–In / Check–Out” feature isavailable.

Feature Reference Section 3, Features,HOTEL APPLICATION

29

4.3 System ProgrammingUser Password

125

Description Assigns the password required for entering the User Programmingmode.In the User Programming Mode, any display proprietary telephoneuser in the system can set the following programs:

[000] Date and Time Set[001] System Speed Dialing Number Set[002] System Speed Dialing Name Set[003] Extension Number Set[004] Extension Name Set[005] Flexible CO Button Assignment[006] Operator / Manager Extension Assignment[007] DSS Console Port and Paired Telephone Assignment[008] Absent Messages[009] Emergency Dial Number Set[010] Budget Management[011] Charge Margin Rate

Selection Password: 4 through 7 digits

Default 1234


Display: User Password

2. Press NEXT.

Display example: Password:1234

3. Enter a password.

To change the current entry, press CLEAR and enter the newpassword.

4. Press STORE.

5. Press END.

Conditions • The password can be from four to seven digits long. Valid numbers arefrom 0 to 9.

• If less than four digits are entered, they will not be stored.• You cannot leave the entry empty.

Feature Reference Section 3, Features,––User Manual User Programming Mode

30

4.4 Timer ProgrammingMessage Waiting Ring Interval Time

216

Description Sets the Message Waiting ring interval time for a single linetelephone.

Selection Time (minutes) : 0 through 64

Default 10 min


Display: MW Ring Time

2. Press NEXT.

Display example: Interval: 10 min

3. Enter the time.

To change the current entry, press CLEAR and enter the new time.

4. Press STORE.

5. Press END.

Conditions When the interval time is set to “0,” the telephone does not ring forMessage Waiting notification.

Feature References Section 3, Features,Message Waiting

31

4.4 Timer ProgrammingTimed Reminder Alarm Repeat Times

217

Description Sets the number of times Timed Reminder alarm is tried.

Selection Number of times : 1 through 5

Default 3 times


Display: Alarm Times

2. Press NEXT.

Display example: Attempt:3

3. Enter the time.


4. Press STORE.

5. Press END.

Conditions One attempt is equivalent to 30 seconds.

Feature References Section 3, Features,Timed Reminder

32

4.4 Timer ProgrammingTimed Reminder Alarm Interval Time

218

Description Sets the Timed Reminder alarm interval time.

Selection Time (seconds) : 30 through 240

Default 60 sec


Display: Alarm Interval

2. Press NEXT.

Display example: Interval: 60 sec

3. Enter the time.


4. Press STORE.

5. Press END.

Conditions None

Feature References Section 3, Features,Timed Reminder

33

4.6 CO Line ProgrammingCO Line Name Assignment

417

Description Used to name CO lines. The preset name is shown on a displayproprietary telephone when an incoming outside call is placed tothe telephone.

Selection • CO line number:KX-TD816 – 01 through 08, ( =all CO lines)KX-TD1232 – 01 through 24, ( =all CO lines)

• Name: 10 characters (max.)

Default All CO lines – Not stored

Programming 1. Enter 417.Display: CO Line Name

2. Press NEXT.Display: CO Line NO?→

3. Enter a CO line number.To enter CO line number 01, you can also press NEXT.Display example: CO01:Not Stored

4. Enter a name.

For entering characters, see Section 4.1.3 “Entering Characters.” To delete the current entry, press CLEAR.To change the current entry, press CLEAR and enter the new name.

5. Press STORE.

6. To program another CO line, press NEXT or PREV, orSELECT and the desired CO line number.


8. Press END.

Conditions • In the case of KX-TD1232, CO01 through CO12 are for the MasterSystem and CO13 through CO24 are for the Slave, if available.

• There is a maximum of 24 names. Each name has a maximum of 10characters.

• To assign all CO lines to one selection, press the key in step 3. Inthis case, the display shows the contents programmed for CO01.

Feature References Section 3, Features,CO Incoming Call Information DisplayDisplay, Call Information

4.6 CO Line ProgrammingISDN Line Number Assignment

34

418

Description Assigns your telephone number of the ISDN network line. Yourtelephone number is informed to the called party with the CLIP(Calling Line Identification Presentation) feature offered by theISDN network service.

Selection • CO line number: KX-TD816 – 05 through 08KX-TD1232 – 09 through 12, 21 through 24

• Telephone number: 16 digits (max.)

Default All CO lines – Not stored

Programming 1. Enter 418.Display: ISDN CO NO.


3. Enter a CO line number.To enter CO line number 05 for KX-TD816 or 09 for KX-TD1232,you can also press NEXT.

Display example: CO09:Not Stored

4. Enter the telephone number. To delete the current entry, press CLEAR. To change the currententry, press CLEAR and the new number.

5. Press STORE.



8. Press END.


• To display parts of the number which have scrolled off the display,press or .

• Your telephone number is informed to the called party if outgoing CLIRfeature is disabled for the ISDN line by program [419] “ISDN OutgoingCLIR Service Assignment.”

Feature References Section 3, Features,CO Incoming Call Information DisplayCO Incoming Call Information LogDirect Dialing In (DDI)

4.6 CO Line ProgrammingISDN Outgoing CLIR Service Assignment

419

35

Description Assigns whether ISDN CLIR (Calling Line IdentificationRestriction) service is enabled or disabled for outgoing outsidecalls. If disabled, the subscriber’s number of your system isinformed to the called party.

Selection • CO line number:KX-TD816 – 05 through 08, ( =all CO lines)KX-TD1232 – 09 through 12, 21 through 24, ( =all CO lines)

• Enable / Disable

Default All CO lines – Enable

Programming 1. Enter 419.Display: ISDN CLIR Send



Display example: CO09:Enable


5. Press STORE.



8. Press END.


• To assign all CO lines to one selection, press the key in step 3. Inthis case, the display shows the contents programmed for CO05 (forKX-TD816) or CO09 (for KX-TD1232).

• Program [418] “ISDN Line Number Assignment” is used to store thesubscriber’s number of your system that is informed to the called party.

Feature References Section 3, Features,Calling Line Identification Restriction (CLIR)CO Incoming Call Information Display

4.6 CO Line ProgrammingISDN DDI Service Assignment

36

420

Description Enables or disables ISDN DDI service per CO line.

Selection • CO line number:KX-TD816 – 05 through 08, ( =all CO lines)KX-TD1232 – 09 through 12, 21 through 24, ( =all CO lines)


Default All CO lines – Disable


Display: ISDN DDI

2. Press NEXT.

Display: CO Line NO?→


Display example: CO09:Disable


5. Press STORE.



8. Press END.


• To assign all CO lines to one selection, press the key in step 3. Inthis case, the display shows the contents programmed for CO05 (forKX-TD816) or CO09 (for KX-TD1232).

Feature References Section 3, Features,Direct Dialling In (DDI)

4.6 CO Line ProgrammingPay-Tone Assignment

423

37

Description Enables Pay-Tone for the CO lines.

Selection • CO line number:KX-TD816 – 01 through 08, ( =all CO lines)KX-TD1232 – 01 through 24, ( =all CO lines)


Default All CO lines – Disable

Programming 1. Enter 423.Display: Pay-Tone Asn


3. Enter a CO line number.To enter CO line number 01, you can also press NEXT.

Display example: CO01:Disable


5. Press STORE.



8. Press END.

Conditions • An optional Pay Tone Card (KX-TD189) must be installed on COboard to receive the Pay-Tone.

• In the case of KX-TD1232, CO01 through CO12 are for the MasterSystem and CO13 through CO24 are for the Slave.

• To assign all CO lines to one selection, press the key in step 3. Inthis case, the display shows the contents programmed for CO01.

Feature References Section 3, Features,Display, Call InformationHOTEL APPLICATION

4.8 Extension ProgrammingISDN DDI Number / Extension Number Transformation

610

38

Description Used to convert a DDI number to an extension number in order toput an incoming DDI call to a specific extension.

Selection • Jack number: KX-TD816 – 01 through 16 (-1 / -2),KX-TD1232 – 01 through 64 (-1 / -2),(-1 = first part, -2 = second part)

• DDI Number: 1 through 6 digits

Default All jacks – Not stored


Display: EXT. DDI NO.

2. Press NEXT.

Display: Jack NO?→



To select the second part (-2), press NEXT after entering a jacknumber.

Display: #01-1:001

4. Enter a DDI number.


5. Press STORE.



8. Press END.

Conditions • There is a maximum of 128 DDI numbers. Each DDI number can beone through six digits, consisting of 0 through 9.

• In the case of KX-TD1232, jack numbers 01 through 32 are for theMaster System and 33 through 64 are for the Slave, if available.

• For an explanation of jack numbering, see “Rotation of jack number”on page 4-7 of the Installation Manual.

Feature References Section 3, Features,Direct Dialing In (DDI)

4.8 Extension ProgrammingISDN DDI Number / Floating Number Transformation

611

39

Description Used to convert a DDI number to an floating number in order toput an incoming DDI call to a specific floating station.

Selection • Floating Station : KX-TD816 – Operator / Pager 1 KX-TD1232 – Operator / Pager 1 / Pager 2 /

Pager 3 / Pager 4 / DISA 1/DISA 2 / MODEM

• DDI Number : 1 through 6 digits

Default All floating stations – Not stored


Display: F.EXT. DDI NO.

2. Press NEXT to program the operator.

Display: Operator:

3. Enter a DDI number.


4. Press STORE.

5. To program another floating station, press NEXT or PREVuntil and the desired floating station is displayed.


7. Press END.

Conditions Each DDI number can be one through six digits, consisting of 0 through9.

Feature References Section 3, Features,Direct Dialing In (DDI)

4.9 Resource ProgrammingSMDR Output Mode

815

40

Description Assigns the SMDR Output Mode. There are two standardsavailable – Regular and Charge.

Selection Regular / Charge

Default Regular


Display: SMDR Output Mode

2. Press NEXT.

Display example: SMDR:Regular


4. Press STORE.

5. Press END.

Conditions • Select the Output Mode used by your SMDR.• If you assign for Charge, you can select the display in Meter / in Charge

through Program [120] “Charge Display Selection.”

Feature References Section 3, Features,Station Message Detail Recording (SMDR)

4.10 Option ProgrammingSystem Additional Information

990

41

Description Field (27) is added to Area 4, (28) through (33) are added to Area 5and (35) is added to Area 6.

ReferencesDefaultSelectionDescriptionField(27) Enables or disables the CO pulse

feedback tone when a dialed number issent to the line.

0 : disable1 : enable

1 None

Explanation for Area 4

Area 6

Displayexample 1111111111111111

Field number unused (35)↓ ↓

Area 4 KX-TD1232 – [17] through [24] below match CO lines 17 through 24:


CO number [24][23][22] [21][20][19][18][17]

↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓

(unused) (27)(unused)(25)(24) (23)Field number

↓ ↓ ↓ ↓ ↓ ↓


unused (36)(33)(32)(31) (34) (30)(29)(28)

↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓Field number un-

usedun-used

Area 5

4.10 Option ProgrammingSystem Additional Information (contd.)

990

42

DefaultSelectionDescriptionField(28)(29)(30)(31)

(32)

(33)

(34)

(35)

(36)

ISDN Layer 1 active modeISDN Data Link modeISDN TEI modeIn the day mode, selects thedestination when theincoming DDI number is afloating number of theoperator.In the night mode, selectsthe destination when theincoming DDI number is afloating number of theoperator.Assigns whether the newpage is ejected or not whenthe Hotel Application isprinted out by SMDR.Assigns the reference modewhether the DDI callnumber of ISDN shows thewhole number or one digit ata time.Sets the time afterterminating the OGM.Enables or disables theSMDR printout for TimedReminder when it starts andit is not answered.

0 : By call 1 : Permanent0 : By call 1 : Permanent0 : Fix (0) 1 : Automatic0 : DIL 1:N 1 : Operator

0 : DIL 1:N 1 : Operator

0 : Disable 1 : Enable

0 : whole number1 : one digit at a time

0 : 0 sec. 1 : 5 sec.

0 : Disable 1 : Enable

1101

1

0

0

1

1

Explanation for Area 5 and 6Reference

NoneNoneNone

Direct Dial In(DDI)

Direct Dial In(DDI)

HotelApplication

Direct Dial In(DDI)

DISAOGMSMDR forTimedReminder

Selection • Area code: 01 (area 1) / 02 (area 2) / 03 (area 3) / 04 (area 4) /05 (area 5) / 06 (area 6) / 07 through 12 are reserved

• Field number : 01 through 36• Selection: See “Selection” shown above and on pages 4-127

through 4-129 in the main Installation Manual.

Default See “Default” shown above and on pages 4-127 through 4-129 inthe main Installation Manual.

For programming instruction, please refer to the program [990] “System Additional Information” in themain Installation Manual.

43

Changed Features

44

SECTION OFTHE MANUAL

FEATURE TITLE REVISION

Direct Inward SystemAccess (DISA)

Section 3Disconnectedafter 5 seconds.

Display, CallInformation

Section 3 This feature has been replaced with a new one. Fordetails, refer to page 46.

Number Feature Default54 Reserved

55-62 Emergency call 1 through 8 none63 Timed reminder, remote 764 CO incoming call information log mode 5665 CO incoming call information log lock 5766 Check-out ready 736

Section 4[100] Flexible Numbering

Feature Number List — Additional numbers

DSS Console (KX-T7240 / KX-T7040)

Section 3 If a port connected to a DSS Console is programmedas a XDP jack, a SLT can be connected to the port inparallel.

[001] System SpeedDialing Number Set

Section 4

Section 4[002] System SpeedDialing Name Set

These programs have been replaced with new ones.For details, refer to pages 52 through 54.

Do Not Disturb (DND) Section 3 Conditions• DND also works for doorphone calls.

Message Waiting Section 3

Section 3

This feature has been replaced with a new one. Fordetails, refer to page 47.

Station Message DetailRecording (SMDR)

Section 3 This feature has been replaced with a new one. Fordetails, refer to page 48.

This timer can be changed to 0 second by program[990] “System Additional Information, Field (35).”

Operator Both operators (1 and 2) have the ability to perform alloperator service features.

45

SECTION OFTHE MANUAL

FEATURE TITLE REVISION

[211] Dial Start Time Section 4 Default 500 ms

[601] Class of Service Section 4 This program has been replaced with a new one. Fordetail, refer to page 57.

[109] Expansion Unit Type

Section 4 This program has been replaced with a new one.For details, refer to page 55.

[412] Pause Time Section 4

Default All CO line groups — 96 ms[413] Flash Time Section 4

Default All CO line groups — 4.5 sec

[990] SystemAdditional Information

Section 4 Default Field (17) — 0

Default Field (26) — 0

46

D 3 Features

Display, Call Information

Description A display-type proprietary telephone shows the user the followingcall information:

Extension number and nameThese are shown when calling or when called by anextension user and during an established intercom call. A display example: 123: Smith

Dialed telephone numberThis is shown when dialing the telephone number. A display example: 91234567890

Number or name of the callerThese are shown when receiving an incoming outside callon ISDN network.Display examples: 0712225555

JOHN WHITECO line number and name

This is shown when receiving an outside call. A display example: CO03:AB COMPANY

Charge MeterThis is shown during an established call.A display example: CO01:00005

Charge FeeThis is shown during an established call.A display example: CO01:00001.15KC

Call durationThis is shown during an established outside call. Thedisplay remains for five seconds after the call is finished. A display example: CO 02 0:02'28

Conditions • Extension numbers and names, and CO line names are programmable.If no name is stored, only the number is displayed.

• The display shows no intercom call duration.• The outgoing outside call duration starts when the programmable timer

expires.• It is programmable to select the first display, meter or charge, by system

programming. To alternate the display, press the FWD/DND button.

Programming ReferencesSection 4, System Programming,[003] Extension Number Set[004] Extension Name Set[120] Charge Display Selection

47

3 Features M[121] Assignment of Denomination[212] Call Duration Count Start Time[417] CO Line Name Assignment[423] Pay-Tone AssignmentStation Programming .......................................................User ManualCharge Fee Reference – New Rate Set

Feature References Section 3, Features,Charge Fee Reference

Operation References DPT Features, —User Manual Display Call Information

Message Waiting

Description The system supports the ability to inform the called party of awaiting message. The user, with a MESSAGE button, knows thereis a message if the LED of the MESSAGE button is lit red. Even ifthe button is not provided nor assigned, the called party hears aspecial dial tone, when he / she goes off-hook. Pressing the litMESSAGE button also means to call back the extension that leftthe message or listen to the messages which are stored in themailbox of a Voice Processing System.

Conditions • For a proprietary telephone which is not provided with a MESSAGEbutton, a flexible CO button can be assigned as the MESSAGE buttoneither by System or Station Programming.

• Cancelling a message can be performed from the extension setting it orfrom the extension receiving it.

• The system supports a maximum of 128 simultaneous messages. • Messages are always left on the original extension. It is not sent to a

Call Forwarding or Station Hunting destination. • A single line telephone or KX-T7052 user will hear the ring tone as a

notification, if he / she receives a message. It is programmable to setthe interval of a ring tone by System Programming.

Programming ReferencesSection 4, System Programming,[005] Flexible CO Button Assignment[100] Flexible Numbering, Message [216] Message Waiting Ring Interval Time[990] System Additional Information, Field (9)Station Programming .......................................................User Manual, Flexible Button Assignment – Message Waiting (MESSAGE) Button

48

S 3 Features

Feature References Section 3, Features,Dial Tone, Distinctive Voice Mail Integration

Operation References DPT Features, SLT Features;—User Manual Message Waiting

Station Message Detail Recording (SMDR)

Description Station Message Detail Recording (SMDR) automatically recordsdetailed call information for outside calls. A printer connected tothe EIA (RS-232C) port can be used to print incoming andoutgoing outside calls as well as print a hard copy of SystemProgramming. To print the call records, use the program [800]“SMDR Incoming / Outgoing Call Log Printout,” which allows youto print out the following records:

• Records of all outgoing outside calls or outgoing toll calls.• Record of incoming outside calls.

There are three types of the call record, which are the regular callrecord, the charge call record and the meter call record.

Date Time Ext CO Dial Number Duration Acc code CD

06/24/96 10:03AM 101 01 123456789012345678901234567890 00:05'12 1234567890

06/24/96 10:07AM 103 20 <INCOMING> 00:00'56

06/24/96 10:08AM 104 10 <INCOMING> 00:00'20 431211

06/24/96 10:08AM 105 10 <INCOMING> 00:10'01 431211 TR

06/24/96 10:09AM 280 14 10222P1-202-346-7890 00:09'18 001 FW

06/24/96 10:10AM 103 20 <INCOMING> 00:01'24

06/24/96 10:11AM 280 12 <INCOMING> 00:00'24

06/24/96 10:11AM 280 22 0924312111 00:03'02 D1

06/24/96 10:20AM 120 13 <INCOMING> 00:21'46 RM•••

(1)

•••

(2)

•••

(3)

•••

(4)

•••

(5)

•••

(6)

•••

(7)

•••

(8)

An example of a printed regular call record: When selected for the regular display byProgram [815] “SMDR Output Mode.”

49

3 Features SAn example of a printed charge call record: When selected for charge by Program[815] “SMDR Output mode” and selected for charge display by program [120] “ChargeDisplay Selection.”

Date Time Ext CO Dial Number Duration Cost Acc code CD

06/24/96 10:03AM 101 01 12345678901234567890 00:05'12 00382.81KC 1234567890

06/24/96 10:07AM 103 20 00:00'56 00000.00KC

06/24/96 10:08AM 104 10 00:00'20 00000.00KC 431211

06/24/96 10:08AM 105 10 00:10'01 00000.00KC 431211 TR

06/24/96 10:09AM 280 14 10222P1-202-346-7890 00:09'18 00560.00KC 001 FW

06/24/96 10:10AM 103 20 00:01'24 00000.00KC

06/24/96 10:11AM 280 12 00:00'24 00000.00KC

06/24/96 10:11AM 280 22 0924312111 00:03'02 00128.00KC D1

06/24/96 10:20AM 120 13 00:21'46 00000.00KC•••

(1)

•••

(2)

•••

(3)

•••

(4)

•••

(5)

•••

(6)

•••

(7)

•••

(8)

•••

(9)

An example of a printed meter call record: When selected for charge by Program [815]“SMDR Output Mode” and selected for meter display by Program [120] “Charge DisplaySelection.”

Date Time Ext CO Dial Number Duration Cost Acc code CD

06/24/96 10:03AM 101 01 12345678901234567890 00:05'12 00015 1234567890

06/24/96 10:07AM 103 20 00:00'56 00000

06/24/96 10:08AM 104 10 00:00'20 00000 431211

06/24/96 10:08AM 105 10 00:10'01 00000 431211 TR

06/24/96 10:09AM 280 14 10222P1-202-346-7890 00:09'18 00520 001 FW

06/24/96 10:10AM 103 20 00:01'24 00000

06/24/96 10:11AM 280 12 00:00'24 00000

06/24/96 10:11AM 280 22 0924312111 00:03'02 00000 D1

06/24/96 10:20AM 120 13 00:21'46 01040 RM•••

(1)

•••

(2)

•••

(3)

•••

(4)

•••

(5)

•••

(6)

•••

(7)

•••

(8)

•••

(10)

50

S 3 Features

*: Available for KX-TD1232 only.

Example of SMDR printout format:Explanation(1) Date : shows the date of the call as Day / Month / Year.(2) Time : shows the end time of a call as Hour:Minute /

AM or PM.(3) Ext : shows the extension number, floating number, etc.

that engaged in a call.(4) CO : shows the CO line number used for the call.(5) Dial Number

Outgoing call: shows the other party’s telephone number (Regular call record : Max. 30 digits, Charge orMeter call record : Max. 20 digits). Valid digits are 0through 9, , #, P (if PAUSE button is pressed), or themark “=” (if a host PBX access code is entered). Received call: shows <INCOMING> and .

(6) Duration : shows the duration of the call as Hours / Minutes / Seconds.

(7) Acc Code (Account Code): shows the account code appended to the call.

(8) CD (Condition Code): shows call handling type with the following codes:

TR: TransferFW: Call Forwarding to CO Line

*D0: Non Security CO Line Access using DISA*D1 through D4: DISA User Codes 1 through 4

RM: Remote access to a modemTo print out the record of System Programming items thathave been assigned, use the program [802] “System DataPrintout.”

(9) Cost : shows the charge.(10) Cost : shows the meter.

Conditions • Connect a printer provided with an EIA (RS-232C) interface to the EIA(RS-232C) connector located on the main unit.

• When programmed for outgoing toll calls only, printing occurs only forcalls which start with the numbers stored in any Denied Code Tablefrom levels 2 to 6. If ARS is employed, not the user-dialed but themodified number is checked against these tables.

• This system can store information up to 100 calls. If more calls areoriginated or received, previous records are deleted starting from theoldest one.

• This data is not deleted when you reset the system.

51

3 Features S• If the system clock is not set by System Programming or if the calendar

IC is out of order, the date and time is not printed out.• If FLASH Signal is manually sent out during a conversation, the call

record is printed and a new record is started.

Connection ReferencesSection 2, Installation,2.3.10 Printer Connection

Programming ReferencesSection 4, System Programming,[000] Date and Time Set[120] Charge Display Selection[212] Call Duration Count Start Time [800] SMDR Incoming / Outgoing Call Log Printout[801] SMDR Format [802] System Data Printout [806]–[807] EIA (RS-232C) Parameters[815] SMDR Out put Mode



4.2 Manager ProgrammingSystem Speed Dialing Number Set

52

Description Used to program the System Speed Dial numbers. These numbersare available to all extension users. There are 500 numbers, from000 to 499.

Selection • Speed dial number: 000 through 499• Telephone number: 24 digits (max.)

Default All speed dial numbers – Not stored

Programming 1. Enter 001.Display: SPD Number Set

2. Press NEXT.Display: SPD Code?→

3. Enter a speed dial number.To enter speed dial number 000, you can also press NEXT.

Display example: 000: Not Stored

4. Enter a telephone number.To delete the current entry, press CLEAR.

To change the current entry, press CLEAR and the new number.

5. Press STORE.

6. To program another speed dial number, press NEXT orPREV, or SELECT and the desired speed dial number.


8. Press END.

Conditions • There is a maximum of 500 speed dial numbers. Each speed dialnumber has a maximum of 24 digits. The valid characters are 0through 9, , and # keys, FLASH, PAUSE, SECRET and –(hyphen) buttons.

– To store the flash signal, press FLASH.Note: The stored flash will be in effect only during an

established call. (Refer to Section 3 “External FeatureAccess.”)

– To store a hyphen, press the “–” button.

001

4.2 Manager ProgrammingSystem Speed Dialing Number Set (contd.)

001

53

– To store a pause, press PAUSE. (Refer to Section 3 “Pause Insertion, Automatic.”)

– To store the feature number to convert pulse signals to DTMFsignals, press the # keys.(Refer to Section 3 “Pulse to Tone Conversion.”)

– To prevent the display of all or part of the number, press SECRETbefore and after confidential parts of the number. The SECRETbutton must always be entered in a pair, or your entry is not stored.(Refer to Section 3 “Secret Dialing.”)

• If you are storing an external number, include the line access code(default=9, 81 through 88) before the number. When dialing, pause isautomatically inserted after the code.

• If you are storing an account code, enter the account code before theline access code. (Refer to Section 3 “Account Code Entry.”)

• If you are storing a number for CO Incoming Call Information Displaywith name, enter “–” (hyphen) after the line access code. The systemstarts to compare the calling party’s number with the System SpeedDialing Number stored after “–.” Example : 9-12345678(Refer to Section 3 “CO Incoming Call Information Display.”)

• It is possible to store a number consisting of 25 digits or more bystoring it in two speed dial numbers. A line access code should not bestored in the second speed dial number.

• To go to another speed dial number in steps 3 through 6, pressSELECT and start with step 3.

• To display parts of the number which have scrolled off the display,press or .

• Program [002] “System Speed Dialing Name Set” is used to give namesto speed dial numbers.

Feature References Section 3, Features,Special Display Features for KX-T7235 — System Speed Dialing System Speed Dialing

4.2 Manager ProgrammingSystem Speed Dialing Name Set

54

Description Assigns names to the system speed dial numbers assigned inprogram [001] “System Speed Dialing Number Set.” The largedisplay telephone (KX-T7235) shows the stored name whenperforming System Speed Dialing.

Selection • Speed dial number: 000 through 499• Name: 10 characters (max.)

Default All speed dial numbers – Not stored


Display: SPD Name Set

2. Press NEXT.

Display: SPD Code?→

3. Enter a speed dial number.

To enter speed dial number 000, you can also press NEXT.

Display example: 000: Not Stored

4. Enter a name.For entering characters, see Section 4.1.3 “Entering Characters.” To delete the current entry, press CLEAR.To change the current entry, press CLEAR and the new name.

5. Press STORE.

6. To program another speed dial number, press NEXT orPREV, or SELECT and the desired speed dial number.


8. Press END.

Conditions • Speed dial numbers are programmed in program [001] “System Speed Dialing Number Set.”

• There is a maximum of 500 names. Each name has a maximum of 10characters.

• To go to another speed dial number at steps 3 through 6, pressSELECT and start with step 3.

Feature References Section 3, Features,Special Display Features for KX-T7235 — System Speed Dialing

002

4.3 System ProgrammingExpansion Unit Type

109

55

Description Assigns the type of expansion units to be used in the system. Thisallows the system to identify the unit in each expansion location.

Selection KX-TD816• Areas 1; 2 = C (4CO) / S (2S0) / E (EXT)KX-TD1232• Master / Slave• Areas 1; 2; 3 = C (4CO) / S (2S0) / E1 (EXT1) / E2 (EXT2)

Default KX-TD816: C; EKX-TD1232: Master and Slave — C; E1; E2

Programming KX-TD8161. Enter 109.

Display: Expansion Card

2. Press NEXT.Display example: C; E


4. Press .


6. Press STORE.

7. Press END.

KX-TD12321. Enter 109.

Display: Expansion Card

2. Press NEXT to program the Master System.To program “Slave,” press NEXT twice.

Display example: Master.: C; E1; E2


4. Press .


6. Repeat steps 4 and 5 until all the required entries arecompleted.

4.3 System ProgrammingExpansion Unit Type (contd.)

56

109

7. Press STORE.If only one system is in operation, go to step 8.

8. Press NEXT to program the Slave System.

Display example: Slave: C; E1; E2


10. Press END.

Conditions • There are two expansion areas in KX-TD816, areas 1 and 2 frombottom to top. One 8-Station Line Unit and either one 4-CO Line Unitor 2-ISDN S0 Line Unit can be installed.

• There are three expansion areas in each system for KX-TD1232, areas1, 2 and 3 from bottom to top. Up to two 8-Station Line Units andeither one 4-CO Line Unit or 2-ISDN S0 Line Unit can be installed ineach system.

• In case of starting the system for the first time or System Data Clear, theapplication for location will adapt the practical installation instead ofsystem default setting.

• If the Slave System is out-of-service of KX-TD1232, skip steps 8 and 9.• After changing the setting, unplug the system once and plug it in again.

Otherwise, the previous setting will remain.

Feature References Section 3, Features,Module Expansion

4.8 Extension ProgrammingClass of Service

601

57

Description Programs each extension for a Class of Service (COS). The COSdetermines the call handling abilities of an extension. Primary andsecondary COS numbers can be assigned per extension.

Selection • Jack number : KX-TD816 – 01 through 16, (-1 / -2),KX-TD1232 – 01 through 64, (-1 / -2),( = all jacks, -1 = first part, -2 = second part)

• COS number: 1 through 8

Default All jacks-1/2 – COS 1, COS 1

Programming 1. Enter 601.Display: COS Assign

2. Press NEXT.Display: Jack NO?→

3. Enter a jack number.To enter jack number 01, you can also press NEXT.To select the second part (-2), press NEXT after entering a jacknumber.Display example: #01-1:COS1, COS1

• The Primary COS is blinking on the displays.To change the Primary COS number, dial the number (1 - 8).

4. Press .Display example: #01-1:COS1, COS1

• The Secondary COS is blinking on the displays.To change the Secondary COS number, dial the number (1 - 8).

5. Enter a COS number.To change the current entry, enter the new number.

6. Press STORE.



9. Press END.

4.8 Extension ProgrammingClass of Service (contd.)

601

58

Conditions • There is a maximum of eight Classes of Service. Every extensionmust be assigned to a Class of Service and is subject to the COSProgramming programs [500] through [508] and [991].

• In the case of KX-TD1232, jack numbers 01 through 32 are for theMaster System and 33 through 64 are for the Slave, if available.Jack numbers in the out-of-service system are unacceptable.

• For an explanation of jack numbering, see “Rotation of jack number”on page 4-7.

• To assign all jacks to one COS, press the key in step 3. In thiscase, the display shows the contents programmed for Jack 01.

• Program [811] “DISA User Codes” is also used to assign a Class ofService to a DISA User Code.

Feature References Section 3, Features,Class of Service (COS)HOTEL APPLICATION — Check-in / Check-out

59

Deleted Features

SECTION OF THE MANUALFEATURE TITLE

4.5 CO Line Programming[405] CPC Signal Detection Incoming Set

[415] CPC Signal Detection Outgoing Set 4.5 CO Line Programming

[110] Caller ID Code Set

[111] Caller ID Name Set

[406] Caller ID Assignment

4.3 System Programming

4.3 System Programming

Caller ID

Calling Party Control (CPC) Signal Detection

3 Features

3 Features

4.5 CO Line Programming

60

Programming Tables

[001] - [002] System Speed Dialing Number / Name Set

Item :

SPD No.

Default

000

001

002

003

004

005

006

007

008

009

010

011

012

013

014

015

016

017

018

019

020

021

022

023

024

025

026

027

028

029

030

031

032

033

034

035

Parameter for [001]:Telephone number

(24 digits max.)

Parameter for [002]:Name

(10 characters max.)Item :

SPD No.

036

037

038

039

040

041

042

043

044

045

046

047

048049

050

051

052

053

054

055

056

057

058

059

060

061

062

063

064

065

066

067

068

069

070

071



All : Not stored

61

Programming Tables


Item :

SPD No.

Default

072

073

074

075

076

077

078

079

080

081

082

083

084

085

086

087

088

089

090

091

092

093

094

095

096

097

098

099

100

101

102

103

104

105

106

107


(24 digits max.)



SPD No.

108

109

110

111

112

113

114

115

116

117

118

119

120121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143



All : Not stored

62

Programming Tables


Item :

SPD No.

Default

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179


(24 digits max.)



SPD No.

180

181

182

183

184

185

186

187

188

189

190

191

192193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215



All : Not stored

63

Programming Tables


Item :

SPD No.

Default

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251


(24 digits max.)



SPD No.

252

253

254

255

256

257

258

259

260

261

262

263

264265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

282

283

284

285

286

287



All : Not stored

64

Programming Tables


Item :

SPD No.

Default

288

289

290

291

292

293

294

295

296

297

298

299

300

301

302

303

304

305

306

307

308

309

310

311

312

313

314

315

316

317

318

319

320

321

322

323


(24 digits max.)



SPD No.

324

325

326

327

328

329

330

331

332

333

334

335

336337

338

339

340

341

342

343

344

345

346

347

348

349

350

351

352

353

354

355

356

357

358

359



All : Not stored

65

Programming Tables


Item :

SPD No.

Default

360

361

362

363

364

365

366

367

368

369

370

371

372

373

374

375

376

377

378

379

380

381

382

383

384

385

386

387

388

389

390

391

392

393

394

395


(24 digits max.)



SPD No.

396

397

398

399

400

401

402

403

404

405

406

407

408409

410

411

412

413

414

415

416

417

418

419

420

421

422

423

424

425

426

427

428

429

430

431



All : Not stored

66

Programming Tables


Item :

SPD No.

Default

432

433

434

435

436

437

438

439

440

441

442

443

444

445

446

447

448

449

450

451

452

453

454

455

456

457

458

459

460

461

462

463

464

465


(24 digits max.)



SPD No.

466

467

468

469

470

471

472

473

474

475

476

477

478479

480

481

482

483

484

485

486

487

488

489

490

491

492

493

494

495

496

497

498

499



All : Not stored

67

Programming Tables

[010] Budget Management

Item :Jack No.(01-22)-1

-2

Selection

Enable Disable


-2

Selection

Enable Disable


-2

Selection

Enable Disable

Default: allall jacks

01-101-202-102-203-103-204-104-205-105-206-106-207-107-208-108-209-109-210-110-211-111-212-112-213-113-214-114-215-115-216-116-217-117-218-118-219-119-220-120-221-121-2

22-122-223-123-224-124-225-125-226-126-227-127-228-128-229-129-230-130-231-131-232-132-233-133-234-134-235-135-236-136-237-137-238-138-239-139-240-140-241-141-242-142-243-143-2

44-144-245-145-246-146-247-147-248-148-249-149-250-150-251-151-252-152-253-153-254-154-255-155-256-156-257-157-258-158-259-159-260-160-261-161-262-162-263-163-264-164-2

✔

68

Programming Tables

Parameter : 16 digits max.,consisting of 0 – 9

Item :Location

No.

1

2

3

4

5

6

7

8

[009] Emergency Dial Number Set

Default : all - Not Stored

Parameter : 0 through 999

%

Default

0%

[011] Charge Margin Rate

[120] Charge Display Selection

in Meter

in Charge

Default

✔

Selection Parameter :2 characters (max.)

[121] Assignment of Denomination

Default

Not Stored

[100] Flexible Numbering

Feature Default Parameter

54

55

56

57

58

59

60

61

62

63

64

65

66

Reserved

Emergency dial number 1








Timed reminder, remote

CO incoming call information log mode

CO incoming call information log lock

Check-out ready

—

—

—

—

—

—

—

—

—

7

56

57

736

(Selection) 1 - 3 digits, (Valid Entries) 0 - 9, , #

[109] Expansion Unit Type(KX-TD816)

[109] Expansion Unit Type(KX-TD1232)

DefaultParameter :

C, S, E Default (Both)

C ; E C ; E1 ; E2

Parameter: C, S, E1, E2

Master Slave

69

Programming Tables

✔

[122] Charge Verification Assignment

Selection

Enable Disable

Item :Jack No.(01 – 31)

Default: allall jacks

01020304050607080910111213141516171819202122232425262728293031

Selection

Enable Disable

Item :Jack No.(32 – 64)

323334353637383940414243444546474849505152535455565758596061626364

Parameter : 4 – 7 digits,consisting of 0 – 9

[125] User Password

Default

1 2 3 4

[124] Hotel Application

in Meter

in Charge

Default

✔

Selection

[123] Charge Verification ID CodeSet

Default

1 2 3 4

Parameter: 4 digits(0000 through 9999)

[216] Message Waiting Ring Interval Time

Default Parameter:Minute (0 – 64)

10 min. min.

[217] Timed Reminder Alarm Repeat Times

Default Parameter:Number of times (1 – 5)

3 times times

[218] Timed Reminder Alarm Interval Time

Default Parameter:Second (30 – 240)

60 sec sec

70

Programming Tables

[417]CO Line Name

Assignment

[423]Pay-Tone

Assignment

[418]ISDN Line Number

Assignment

[419] ISDNOutgoing

CLIR ServiceAssignment

[420] ISDN DDI

ServiceAssignment

Item :CO Line No.

Parameter : Name(10 characters max.)

Not Stored

SelectionEnable Disable

Parameter : TelephoneNo. (16 digits max.)

Not Stored



Default : all

all CO Lines

01

02

03

04

05

06

07

08

0910

11

12

13

14

15

16

17

18

19

20

21

22

23

24

✔ ✔ ✔

CO line no. for program [428], [419] and [420]:KX-TD816 – 05 through 08KX-TD1232 – 09 through 12, 21 through 24

71

Programming Tables

[601] Class of Service


-2

Parameter : Primary /Secondary COS no.(1-8)

Primary Secondary


-2


-2Default: allall jacks

01-101-202-102-203-103-204-104-205-105-206-106-207-107-208-108-209-109-210-110-211-111-212-112-213-113-214-114-215-115-216-116-217-117-218-118-219-119-220-120-221-121-2

22-122-223-123-224-124-225-125-226-126-227-127-228-128-229-129-230-130-231-131-232-132-233-133-234-134-235-135-236-136-237-137-238-138-239-139-240-140-241-141-242-142-243-143-2

44-144-245-145-246-146-247-147-248-148-249-149-250-150-251-151-252-152-253-153-254-154-255-155-256-156-257-157-258-158-259-159-260-160-261-161-262-162-263-163-264-164-2

11


Primary Secondary


Primary Secondary

72

Programming Tables

[610] ISDN DDI Number / Extension Number Transformation


-2

Parameter : DDI No. (1-6 digits)


-2


-201-101-202-102-203-103-204-104-205-105-206-106-207-107-208-108-209-109-210-110-211-111-212-112-213-113-214-114-215-115-216-116-217-117-218-118-219-119-220-120-221-121-222-122-2

23-123-224-124-225-125-226-126-227-127-228-128-229-129-230-130-231-131-232-132-233-133-234-134-235-135-236-136-237-137-238-138-239-139-240-140-241-141-242-142-243-143-244-144-2

45-145-246-146-247-147-248-148-249-149-250-150-251-151-252-152-253-153-254-154-255-155-256-156-257-157-258-158-259-159-260-160-261-161-262-162-263-163-264-164-2

Default : all - Not StoredChange





73

Programming Tables

[815] SMDR Output Mode

Regular

Charge

Default

✔

Selection

Item :Floating Station

Operator

Pager 1

Pager 2

Pager 3

Pager 4

DISA 1

DISA 2

MODEM

[611] ISDN DDI Number / Floating Number Transformation



74

Programming Tables

[990] System Additional Information

CO17 : 0 (0 dB) / 1 (-3 dB)CO18 : 0 (0 dB) / 1 (-3 dB)

••

CO23 : 0 (0 dB) / 1 (-3 dB)CO24 : 0 (0 dB) / 1 (-3 dB)0 (prevent) / 1 (allow)0 (prevent) / 1 (allow)0 (disable) / 1 (enable)0 (By call) / 1 (Permanent)0 (By call) / 1 (Permanent)0 (Fix) / 1 (Automatic)0 (DIL 1:N) / 1 (Operator)0 (DIL 1:N) / 1 (Operator)0 (disable) / 1 (enable)0 (whole number) / 1 (one digit at a time)0 (0 sec.) / 1 (5 sec.)0 (disable) / 1 (enable)

Field 23-(17)23-(18)

••

23-(23)23-(24)

242527282930313233343536

::::::::::::::::::

Field

Default

Selection

AREA 04 [Fields 23-(17) through 23-(24), 24, 25 and 27]

001—1 ———— 0 0 0 0 0 0 0

25 2423|

(24)

23|

(23)

23|

(22)

23|

(21)

23|

(20)

23|

(19)

23|

(18)

23|

(17)reserved 27 unused

Field

Default

Selection

AREA 05 [Fields 28 through 34 and 36]

10————— 1 — 0 — 0 1 1

3336

— 1

32 31 34 30 29 28unused un-used

un-used

Field

Default

Selection

AREA 06 [Field 35]

—————— — — — 1— —

35unused

— — — —

Note : Field numbers 23 – (9) (CO 09) through 23 – (24) (CO 24) are availablefor TD1232 only.

Printed in Japan PSQX1168ZA S0796MT0 (CE)

Matsushita Electric of Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, Japan

Documents

Added and Changed Features for Installation Manual and ...bucsesz.uw.hu/file/TD_816es1232_install kieg1.pdf · Digital Super Hybrid System KX-TD816CE KX-TD1232CE Added and Changed