Adapter Kit for PanelView 5000 and PanelView Plus …...Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 5 Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance

Installation Instructions

Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals

Catalog Numbers 2711P-RAAT7, 2711P-RAAK7, 2711P-RAAT10, 2711P-RAAK10, 2711P-RAAT12, 2711P-RAAT12K, 2711P-RAAT15, 2711P-RAAK15

Summary of ChangesThis publication contains new and updated information as indicated in the following table.

Topic Page

Summary of Changes 1

Before You Begin 3

Remove the Existing Terminal From the Panel 4

Drill the Holes for the Adapter Kit 4

Install the Adapter Plate and Backing Plate 6

Prepare to Mount the Terminal 8

Mount the Terminal 9

Finish the Terminal Installation and Apply Power to the Enclosure 11

Drill Template Dimensions 12

Additional Resources 16

Topic Page

Changed PanelView 5500 to PanelView 5000. 1, 2

Added ‘Uses Drill Template Cat. No.’ column to Adapter Kit Conversion table. 2

Added PanelView 5310 and PanelView 5510 user manual references to step 1. 11

Added PanelView 5310 and PanelView 5510 literature to the Additional Resources table. 16


About This Adapter KitThis adapter kit includes an adapter plate, gasket, and backing plate that you install into an existing cutout from a PanelView™ Plus 6 or PanelView standard terminal. Read and understand these instructions before you begin to install the adapter plate kit and terminal.

See the Adapter Kit Conversion Table on page 2 to determine the adapter kit for your new and existing terminal.

Adapter Kit Conversion Table

IMPORTANT Do not install a PanelView Plus 7 Standard terminal with this adapter kit. This adapter kit is only for PanelView 5000 and PanelView Plus 7 Performance terminals.

If you install a PanelView Plus 7 Standard terminal into this adapter kit, you can damage the standard terminal bezel. Contaminates can also enter the enclosure and damage components inside the enclosure.

Adapter Kit Cat. No.

Replace this Existing PanelView Plus 6 or PanelView Standard Terminal…

With this PanelView 5000 or PanelView Plus 7 Performance

Terminal

Uses Drill Template Cat. No.

2711P-RAAT7 PanelView Plus 6 700 touch screen 6.5-in. touch screen

VIEW-DS0022711P-RAAK7 • PanelView Plus 6 700 keypad, or keypad with touch screen• PanelView Standard 600 keypad, or keypad with touch

screen

6.5-in. keypad with touch screen

2711P-RAAT10 • PanelView Plus 6 1000 touch screen• PanelView Standard 900 touch screen

10.4-in. touch screen

VIEW-DS0032711P-RAAK10 • PanelView Plus 6 1000 keypad, or keypad with touch screen

• PanelView Standard 900 keypad10.4-in. keypad with touch screen


12.1-in. touch screen

VIEW-DS0042711P-RAAT12K • PanelView Plus 6 1250 keypad, or keypad with touch screen

• PanelView Standard 1000 keypad12.1-in. touch screen


15-in. touch screen

VIEW-DS0052711P-RAAK15 • PanelView Plus 6 1500 keypad, or keypad with touch screen

• PanelView Standard 1400 keypad15-in. keypad with touch screen

2 Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

https://literature.rockwellautomation.com/idc/groups/literature/documents/ds/view-ds002_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/ds/view-ds003_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/ds/view-ds004_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/ds/view-ds005_-en-p.pdf


Adapter Kit ContentsThe adapter kits include these parts:

• Adapter plate with threaded studs and gasket• Backing plate• Mounting clamps• Mounting nuts (10-32)• Drill template• These installation instructions

Required ToolsThese tools are required for installation:

• Clean cloth and a suitable cleanser for dirty panels• Masking tape and marker or grease pencil• Scissors• Center punch and hammer• Drill and drill bits (pilot drill bit 4.76 mm [3/16 in.], finish drill bit 6.35 mm [1/4 in.])• Torque wrench and a 3/8-in. socket• Work gloves

Before You Begin

IMPORTANT Before you install this adapter kit and new terminal, read and understand all of these instructions.

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 3


Remove the Existing Terminal From the Panel

Follow these steps to remove the existing terminal from the panel.

1. Remove all power from the enclosure and the terminal.

2. Disconnect all communication cables from the terminal.

3. While holding the terminal, remove the mounting clamps that secure the terminal in the panel.

4. Remove the terminal from the panel.

Drill the Holes for the Adapter KitFollow these steps to drill the holes for the adapter kit by using the drill template included in this kit.

1. Clean the panel where the drill template will be taped over the existing cutout.

2. Determine which side of the drill template that you need.

ATTENTION: Remove all power from the components in the enclosure and the existing terminal. Disconnect the communication cables from the terminal.

Failure to remove all power and disconnect communication cables can cause electric shock and unexpected communication signals to the machinery.

ATTENTION: Be careful when removing the mounting clamps. The terminals can fall out of the panel after the mounting clamps have been removed. Be sure to hold the terminal in the panel while you remove the mounting clamps, and then carefully remove the terminal from the panel.

Drill Template for PanelView™ 5000 and PanelView Plus 7 Performance Terminals Adapter Kit

For Adapter Kit 2711P-RAAK7Drill Template for PanelView 5000 and PanelView Plus 7 Performance Terminals

6.5-in. Keypad with Touch Screen Adapter Kit

Replaces these Existing Terminals:PanelView Plus 6 700 Keypad, or Keypad with Touch Screen

PanelView Standard 600 Keypad, or Keypad with Touch Screen

Printed Actual Size (scale = 1:1)If you print this drill template from the PDF file, set the paper size on your plotter or printer to 18 x 12 inches.

For dimensions, see the Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance TerminalsInstallation Instructions, publication VIEW-IN002, which is shipped with this drill template.

Identifies the new terminals that can be installed with this drill template.

Identifies the existing terminals that can be replaced with this drill template.



3. Cut out the center white space and the white edges of the drill template, and leave the shaded part of the template that includes the drill locations.

4. Center the drill template over the existing cutout in the panel.

Align the edge of the existing panel cutout with the interior edge of the drill template.

5. Use the masking tape to secure the drill template to the panel.

6. Use a center punch to mark the center of the drill locations.

7. Remove the drill template and masking tape.

8. Cover and protect components in the enclosure or within the drilling vicinity.

9. To drill the pilot holes, use the 4.76 mm (3/16 in.) drill bit.

10. To drill the finish holes, use the 6.35 mm (1/4 in.) drill bit.

11. Remove any burrs from the drilled holes.

12. Remove all drill shavings from inside the enclosure and the vicinity.

13. Remove the temporary covers and protection from the enclosure and drilling vicinity.

IMPORTANT Make sure that the drill template is flat against the panel with no wrinkles or creases that can distort the drill locations.

ATTENTION: Make sure that drill shavings do not enter any components that are installed in the enclosure or in the vicinity. Drill shavings can damage components.

ATTENTION: Use the shortest possible drill bit that will drill completely through the panel. Do not drill into any existing components inside the enclosure.

Publication VIEW-DS002B-EN-P - September 2018

Drill Template for PanelView™ 5000 and PanelView Plus 7 Performance Terminals 6.5-in. Keypad with Touch Screen Adapter Kit

Panel

Edge of the Existing Cutout in the Panel

Edge of the Drill Template



Install the Adapter Plate and Backing PlateBefore you install the adapter and backing plate, measure the thickness of the panel to find the correct mounting lever lock position for the new terminal installation.

Determine the Mounting Lever Lock Position

Use a marker or grease pencil to mark the mounting lever lock position of each mounting slots on the back edge of the new terminal. The marked lock position helps you line up the mounting lever when you install the new terminal in step 4 through step 7 in Mount the Terminal on page 9.

To install the adapter plate and backing plate, follow these steps.

1. Verify that the adapter plate and backing plate are flat and not bent.

2. Verify that the sealing gasket is installed on the adapter plate and is not damaged.

This gasket forms a compression seal. Do not use sealing compounds.

3. From the front of the panel, insert the threaded studs of the adapter plate through the holes that you drilled in the panel.

4. From the back of the panel, insert the backing plate through the threaded studs of the adapter plate.

5. Finger tighten one nut onto each of the threaded studs. Be sure to hold the backing plate securely until at least two nuts are in place.

Mounting Slot

Mounting Lever Lock

PositionPanel Thickness Range Before

the Adapter Kit is InstalledTypical Gauge

1 1.50…2.01 mm (0.060…0.079 in.) 16

2 2.03…2.64 mm (0.080…0.104 in.) 14

3 2.67…3.15 mm (0.105…0.124 in.) 12

4 3.17…3.66 mm (0.125…0.144 in.) 10

5 3.68…4.16 mm (0.145…0.164 in.) 8/9

6 4.19…4.80 mm (0.165…0.188 in.) 7

ATTENTION: For the following steps, refer to Installation Sequence on page 7.

IMPORTANT Install the backing plate with the raised spacers facing the panel.

654321

Notch

Alignment Mark

In this example, the marker or grease pencil identifies mounting lever lock position 3.



6. Follow the tightening sequence on page 7 for your terminal adapter kit.

Installation Sequence

Torque Sequence for Adapter Plate Mounting Nuts–3.90 N•m (30 lb•in)

ATTENTION: To maintain a NEMA Type 4X rating, torque the nuts to 3.90 N•m (30 lb•in).

Rockwell Automation is not responsible for water or chemical damage to the terminal, or other equipment within the panel, due to improper installation.

Adapter Plate with Threaded Studs and Gasket Installed on FrontSide of Panel

Enclosure Panel with Holes that You Drilled

Backing Plate Installed on Back Side of Panel

Raised Spacers Facing the Panel

Adapter Plate Mounting Nuts

2 4

5

7

9

3 110

11

8

612

2 4 68

3 1 75

9

1011

12

13 14

481362

171453

10

12

16

9

11

15

All 6.5-in. Terminals–12 Mounting Nuts

All 10.4-in. Terminals–14 Mounting Nuts

All 12.1-in. and 15-in. Terminals–16 Mounting Nuts



Prepare to Mount the TerminalMounting levers insert into the slots around the terminal bezel to secure the terminal in the adapter plate. The number of mounting levers varies by terminal size. Each slot has six notches with alignment marks that are locking positions for a mounting lever. The thickness of the panel where the terminal is mounted determines the locking position that is required to maintain NEMA, UL Type, and IP seals. See Determine the Mounting Lever Lock Position on page 6.

Mounting Lever Orientation and Lock Sequence

Mounting Lever Orientation and Lock Sequence

IMPORTANT The mounting lever orientations that are shown are required to maintain NEMA, UL Type, and IP seals. If you require a NEMA, UL Type, or IP seal, do not use a mounting lever in another orientation than shown. See Mounting Lever Orientation and Lock Sequence on page 8.

3 1

2 4

56

6.5-in. Touch Only–6 Levers

2 49

7

11

5

6

12

8

103 1

15-in. Touch Only–12 Levers

10

14

11

13

129

15-in. Keypad and Touch–14 Levers8 4 62

5 1 73

Back Sideof Terminal

3 110

6

8

7

5

10.4-in. Keypad and Touch, 12.1-in. Touch Only–10 Levers

2 49

Back Side of Terminal


472

5 6

183

6.5-in. Keypad and Touch–8 Levers



2 48

6

7

53 1

10.4-in. Touch Only–8 Levers


The arrows show the direction to rotate the mounting lever for the final locking position.



Mount the TerminalInstalling the mounting levers is a multi-step process. Step 4 installs each lever so that the terminal is snug in the adapter plate and the gasket is slightly compressed. Step 6 moves the mounting levers into tighter locking positions until you reach the final locking position that you previously marked with a marker or grease pencil.

To mount the terminal in the adapter plate, follow these steps.

1. Verify that the sealing gasket is present on the terminal and is not damaged.

This gasket forms a compression seal. Do not use sealing compounds.

2. Insert adapter kit mounting levers in the top corner slots by using the orientation in Mounting Lever Orientation and Lock Sequence on page 8.

The example at right shows the top of a 6.5-in. touch screen terminal.

3. Tilt the terminal into the adapter plate and guide the terminal upward so that the mounting levers hold the top of the terminal in the adapter plate.

If it is difficult to insert the terminal into the adapter plate, press the bezel at the top of the terminal to compress the gasket so you can insert the terminal into the adapter plate.

4. Insert a mounting lever in the bottom of the terminal to stabilize the terminal in the adapter plate.

IMPORTANT Before you begin to mount the terminal, read this section and understand the process.

IMPORTANT Use only the adapter kit mounting levers. Do not use any other mounting levers.

Use the Adapter Kit Mounting Levers Do Not Use the Oval Mounting Levers



5. Insert the remaining levers in the terminal and rotate each lever until the flat side is in contact with the backing plate and the gasket is slightly compressed.

If it is difficult to insert a mounting lever, press the bezel at the mounting lever position to compress the gasket so you can insert the mounting lever.

6. Readjust each mounting lever to its final lock position.a. Rotate mounting lever one in the sequence away from the backing plate.

b. Slide the mounting lever to the final locking position.

If it is difficult to slide the mounting lever, press on the bezel at the mounting lever position to compress the gasket so you can slide the mounting lever to the final locking position.If it is too difficult to slide a mounting lever to its final locking position, then slide the mounting lever one position at a time until you are able to slide the mounting levers to the final locking position.

c. Rotate the mounting lever until the flat side is in contact with the backing plate.

d. Lock the remaining mounting levers to their final position.

IMPORTANT Install the mounting levers by the orientation sequence shown in Mounting Lever Orientation and Lock Sequence on page 8.

IMPORTANT Do not install the mounting levers in the final lock position yet. For example, if the final lock position is 3, slide the lever to notch 4 or 5 (see Determine the Mounting Lever Lock Position on page 6).

TIP If the mounting levers are over torqued, the pin can break off. If a pin is broken, you can turn the mounting lever over and use the lever in another location that meets the orientation for the mounting lever.

1 2 3 4

Flat Side in Contact With the Backing Plate



7. Inspect all mounting levers and verify that each lever is in the correct locked position.

The notch on the outside of mounting lever shows the locked position. The example at right shows the mounting lever locked in position 4.

The adapter plate and terminal are now installed in the panel.

Finish the Terminal Installation and Apply Power to the Enclosure

1. To complete the power wiring, network cabling, initial startup, and configuration of the terminal, follow the instructions in the user manual for your terminal:• PanelView 5310 Terminals User Manual, publication 2713P-UM001 • PanelView 5500 Terminals User Manual, publication 2715-UM001 • PanelView 5510 Terminals User Manual, publication 2715P-UM001 • PanelView Plus 7 Performance Terminals User Manual, publication 2711P-UM008

2. To return power to the components in the enclosure, follow your approved sequence.

ATTENTION: All mounting levers must be in the correct locked position and follow the correct lever installation sequence to provide an adequate gasket seal between the terminal and the adapter plate. Rockwell Automation assumes no responsibility for water or chemical damage to the terminal or other equipment within the panel because of improper installation.

Outer Notch on Mounting Lever

Alignment Notch on Terminal

Front View Rear View


http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711p-um008_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2713p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715-um001_-en-p.pdf


Drill Template DimensionsThis section includes the layout dimensions for the drill locations of the adapter kit.

6.5-in. Only Touch – Catalog Number 2711P-RAAT7

6.5-in. Keypad and Touch – Catalog Number 2711P-RAAK7

220 (8.66)

154(6.06)

18.5(0.73)

18 (0.7)

257 (10.11)NOTE: All dimensions are in mm (in.)

190(7.48)

110 (4.33)

80 (3.14) 80 (3.14)

77(3.03)

60(2.36)

60(2.36)

6.35 (0.25)

18 (0.7)

18.5(0.73)

264 (10.39)

167(6.57)

132 (5.2)

95(3.74)

83.5(3.29)

60(2.36)

203(8.0)

301 (11.85)

60(2.36)

95(3.74)

6.35 (0.25)

NOTE: All dimensions are in mm (in.)




10.4-in. Keypad and Touch – Catalog Number 2711P-RAAK10

305 (12.0)

224(8.82)

17.5

25 (0.98)

274(10.78)

340 (13.39)

112(4.4)

95(3.74)

120.5 (4.74)

279.5 (11.0)

95(3.74)

95(3.74)

95(3.74)


6.35 (0.25)

375 (14.76)

224(8.82)

17.5 (0.69)

17(0.67)

112(4.41)

95(3.74)

327.5 (12.89)140.5 (5.53)

93 (3.66)

410 (16.14)

25(0.98)

274(10.79)

93 (3.66)


6.35(0.25)




12.1-in. Only Touch – Catalog Number 2711P-RAAT12K

338(13.31)

257(10.12)

43.5(1.71)

18(0.71)

128.5(5.06)

21 (0.83) 169 (6.65)95 (3.74)

359 (14.13)380 (14.96)

293(11.54)

95 (3.74)

95(3.74)

95(3.74)

6.35 (0.25)


390 (15.35)

257(10.12)

18(0.71)

38.5 (1.52)

128.5(5.06)

95(3.74)

95(3.74) 293

(11.54)

195 (7.68)

95 (3.74)190 (7.48) 190 (7.48)

95 (3.74)

467 (18.39)NOTE: All dimensions are in mm (in.)



15-in. Only Touch – Catalog Number 2711P-RAAT15

15-in. Keypad and Touch – Catalog Number 2711P-RAAK15

391 (15.39)

305(12.0)

18(0.71) 26.5

(1.04)

444 (17.48)

341(13.43)

152.5(6.0)

95(3.74)

95(3.74)

195.5 (7.70)375.5 (14.78)

15.5 (0.61)

85 (3.35) 85 (3.35)

6.35 (0.25)


419 (16.50)512 (20.16)

46.5(1.83)

19.5 (0.78)209.5 (8.25)

399.5 (15.73)

6.35 (0.25)


152.5(6.0)

95(3.74)

95(3.74)

18(0.71) 95 (3.74)95 (3.74)

305(12.0)

341(13.43)


Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Resource Description

PanelView 5310 Terminals User Manual, publication2713P-UM001

Provides information on how to install, operate, configure, and troubleshoot the PanelView 5310 terminals.

PanelView 5310 Terminals Technical Data, publication2713P-TD001

Provides technical specifications, environmental specifications, and certifications for the PanelView 5310 terminals.

PanelView 5500 Terminals User Manual, publication2715-UM001


PanelView 5500 Terminals Technical Data, publication2715-TD001


PanelView 5510 Terminals User Manual, publication2715P-UM001


PanelView 5510 Terminals Technical Data, publication2715P-TD001


PanelView Plus 7 Performance Terminals User Manual, publication 2711P-UM008

Provides information on how to install, operate, configure, and troubleshoot the PanelView Plus 7 Performance terminals.

PanelView Plus 7 Performance Terminals Technical Data, publication 2711P-TD009

Provides technical specifications, environmental specifications, and certifications for the PanelView Plus 7 Performance terminals.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1

Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website, rok.auto/certifications

Provides declarations of conformity, certificates, and other certification details.

Allen-Bradley, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website athttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Vendor part number xxxxxxxxxxPublication VIEW-IN002C-EN-P - October 2018 DIR 10001787223_02Supersedes Publication VIEW-IN002A-EN-P - July 2015 Copyright © 2018 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

*PN-518179*PN-518179

http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2715p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/2711p-um008_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2711p-td009_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttps://www.rockwellautomation.com/global/detail.page?pagetitle=Product-Certifications&content_type=tech_data&docid=de1cc7d81606981b0f214fed1137f539http://www.rockwellautomation.com/literature/http://literature.rockwellautomation.com/idc/groups/literature/documents/um/2713p-um001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2713p-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2715-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/2715p-td001_-en-p.pdfhttps://www.rockwellautomation.com/global/news/media-resources.page?pagetitle=Product-Environmental-Compliance&docid=a46a463f8b4046b7165e187a4a88c793http://www.rockwellautomation.com

Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals Installation InstructionsSummary of ChangesAbout This Adapter KitAdapter Kit ContentsRequired Tools

Before You BeginRemove the Existing Terminal From the PanelDrill the Holes for the Adapter KitInstall the Adapter Plate and Backing PlatePrepare to Mount the TerminalMounting Lever Orientation and Lock Sequence

Mount the TerminalFinish the Terminal Installation and Apply Power to the EnclosureDrill Template DimensionsAdditional ResourcesBack Page

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

Introduction_Category Types

This tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released as JIT (print on demand) or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.

Publication Type and Print Category

Publication TypeOff Set Print Category Spec. (See table below)JIT Spec. (See table below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release Option

ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / Internal

APA3D2Application Solution or Customer Success Story5100Presale / External

ARNANAArticle/Editorial/BylineNANAPresale / Internal

(press releases should not be checked into DocMan or printed)

ATB3, B4D5Application techniques5100Presale / External

BRA2 Primary, A1NABrochures5100Presale / External

CAC2 Primary, C1NACatalogue150Presale / External

CGNANACatalogue Guide150Presale / External

CLNANACollection550Presale / External

COA5, A6, A9D5Company Confidential InformationNANANA / Confidential

CPE-onlyE-only, D5Competitive Information550NA / Confidential

DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal

DIA1, A3NADirect Mail5100Presale / Internal

DMNANAProduct Demo550Presale / Internal

DSB3D5Dimensions Sheet15Post / External

DUB3D5Document Update15Post / External

GRB2D6Getting Results15Post / External

INB3 Primary, B2D5, D6Installation instructions15Post / External

LMNANALaunch Materials550Presale / Internal

PCB3D5Packaging Contents

PLE-only primary, B3E-onlyPrice List550Presale / Internal

PMB2D6Programming Manual15Post / External

PPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / External

QRB2 primary, B3, B5D5, D6Quick Reference15Post / External

QSB2 primary, B3, B5D5, D6Quick Start15Post / External

RMB2D5, D6Reference Manual15Post / External

RNB3D5Release Notes15Post / External

SGB1 Primary, B4D5, D6Selection Guide Colour550Presale / External

SGB2D5, D6Selection Guide B/W550Presale / External

SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / Internal

SRB2, B3D5, D6Specification Rating Sheet5100Presale / External

TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / External

TGB2, B3D6Troubleshooting Guide15Post / External

UMB2 Primary, B4D6User Manual B/W15Post / External

WDB3D5Wiring Diagrams / Dwgs15Post / Internal

WPB3 Primary, B5D5White Paper550Presale / External

** Minimum order quantities on all JIT items are based on the publication length. **

Publication lengthMinimum Order Quantity

77 or more pages1 (no shrink wrap required)

33 to 76 pages25

3 to 32 pages50

1 or 2 pages100

Pre-sale / MarketingAll paper in this category is White Brightness, 90% or better. Opacity 90% or better

CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements

A14 color170 gsm 2pp100# gloss cover, 100# gloss text

A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss text

A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss text

A42 color170gsm Silk – 120gsm Silk80# gloss cover, 80# gloss text

A52 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A61 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text

A74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet text

A84 color coverCategory being deleted50# matte sheet text, self cover

2 color text

Selection Guide

A92 color100gsm bond50# matte sheet text, self cover

Selection Guide

Gray shading indicates Obsolete Print Catagories

Post Sale / Technical Communication


B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S

2 color text50# matte sheet text

B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B31 color100gsm bond50# matte sheet text, self cover

B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text

B52 color100gsm bond50# matte sheet text, self cover

Catalogs


C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S

4 color text45# Coated Sheet

C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S

2 color text32#-33# Coated Sheet

JIT / PODAll paper in this category is White Brightness, 82% or better. Opacity 88% or better


D14 color170gsm white silk80# gloss cover, coated 2 sides

D24 color120gsm white silk80# gloss text, coated 2 sides, self cover

D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sides

D41 color160gsm tab90# index

D51 color80gsm bond20# bond, self cover

D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D72 color160gsm tab90# index

D82 color80gsm bond20# bond, self cover

D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond

D10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bond

Gray shading indicates Obsolete Print Catagories

Just In Time (JIT) or Off Set (OS)?

Use these guidelines to determine if your publication should be JIT (just in time/print on demand) or if it would be more economical to print OS (offset/on a press). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the “Either” category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the JIT category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.

Black & White Printing

Color Printing

Color Printing

Print Spec Sheet

JIT Printing SpecificationsRA-QR005J-EN-P - 6/14/2013

Printing SpecificationYOUR DATA HEREInstructionsNO

(required) Publication Number:VIEW-IN002C-EN-PSample: 2030-SP001B-EN-P11” x 17”LOOSE -Loose LeafYESPre-sale / MarketingTOP

Use Legacy Number:YES or NO8.5” x 11”PERFECT - Perfect BoundA1LEFT

Legacy Number if applicable:Sample Legacy Number: 0160-5.338.375” x 10.875SADDLE - Saddle StitchA2RIGHTCORNER

Publication Title:Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals Installation InstructionsSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title8.25” x 11” (RA product profile std)PLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDE

Used in Manufacturing:YESYES or NO - If Yes, must have Part No. listed below8.25” x 10.875”STAPLED1 -1 positionA3

Part Number:PN-518179If SAP Part Number, be sure to enter PN- before the number7.385” x 9” (RSI Std)STAPLED1B - bottom 1 positionA5

(required) CategoryD5Select Print Category A,B,C or D from category list, on "Introduction_Category Types" tab6” x 4”STAPLED2 - 2 positionsA6

Paper Stock Color:White is assumed. For color options contact your vendor5.5” x 8.5” (half-size)THERMAL - Thermal bound (Tape bound)A7

Ink Color:One color assumes BLACK / 4 color assume CMYK / Indicate PMS number here4.75” x 7.75”THERMALO - Thermal Bound (Tape bound - offline)A8

(required) Page Count ofPublication:16Total page count including cover. Enter PAGE count, not SHEET count4.75” x 7” (slightly smaller half-size)A9

(required) Finished Trim Size Width:8.5” x 11”This is sheet size, before folding4.25" x 5.50"Post Sale / Technical Communication

Fold:Review key below. Leave blank if folded for saddle stitching4” x 6”B1

Finished Fold Size:8.5" x 5.5"This is size after folding is completed3” x 5”B2

Binding/Stitching:SADDLE - Saddle StitchReview key below9” x 12” (Folder)B3None

Stitching Location:Blank, Corner or SideA4 (8 ¼” x 11 ¾”) (210 x 297 mm)B4Half or V or Single Fold

Drill Hole (Yes/No):NOAll drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of ¼ inch from the inner page border.A5 (5.83” x 8.26”) (148 x 210 mm)B5C or Tri-Fold

Number of Tabs Needed:5 tab in stock at RR Donnelley36” x 24” PosterCatalogsDbleParll

Number of Pages per Pad:Average sheets of paper. 25, 50 75,100 Max24” x 36” PosterC1Sample

Glue Location on Pad:Glue location on pads18” x 24” PosterC2Short (must specify dimensions between folds in Comments)

(required) Business Group:Marketing CommercialAs entered in DocManJIT/PODZ or Accordian Fold

(required) Cost Center:19141D1Microfold or French Fold - designate no. of folds in Comments - intended for single sheet only to be put in box for manufacturing

Comments:The finished publication will be a half-size booklet: 5.5" x 8.5".D2Double Gate

FoldsHalf, V, Single C or Tri

Dble Parll

Z or Accordian Microfold or French

Double Gate

Short FoldSaddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch -no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)

Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words

Plastcoil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)

Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)D3

D4

D5

D6

D7

D8

D9

MBD000B0209.bin

MBD000B020B.bin

MBD000B020C.bin

MBD000B020A.bin

MBD000B0205.bin

MBD000B0207.bin

MBD000B0208.bin

MBD000B0206.bin

MBD000B0203.bin

MBD000B0204.bin

Documents

Adapter Kit for PanelView 5000 and PanelView Plus …...Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018 5 Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance