Embed Size (px)
Citation preview
Accredited calibration services for medicallaboratoryequipmentTo help you achieve the right quality, our calibration services are accredited according to ISO/IEC 17025, and fullycompliant to GxP and ISO 13485 requirements
Exova METECH provides independent Calibra-tion and Validation services for the Life Science industries - Pharmaceuticals, Biotechnology and Medical Technology.
Our services complies with FDA and GxP requirements, and we provide a wide range of calibration services and solutions for metrologi-cal tasks specifically tailored to the Life Science area.
Calibration areas
We perform ISO/IEC 17025 accredited or trace-able calibration of medical laboratory equipment in the following areas:
•Temperature•Pressure / Vacuum•Humidity•Conductivity•Liquid flow•Gas flow•Slitsampler•Volume (i.e. Pipettes)•Mass (Weight)•Geometry•Torque•Electrical parameters, including pH, oxygen
and time
Validation in temperature, air humidity and CO2
Exova METECH has the experience and capabili-ties to carry out planning, implementation and result handling of validations.
Accredited laboratoryExova METECH performs ISO/IEC 17025 accred-ited or traceable validation (testing) within the following parameters:
•Temperature•Humidity•Carbon dioxide (CO2)
ReportA test certificate for the validation performed is provided, containing documentation for all stages of the validation.
Validation planningExova METECH can also take on validation plan-ning, such as preparation of protocol and a test plan. This is carried out in close collaboration with you as our customer. We can also prepare the complete validation report.
Typical areas for Validation
•Freezers and refrigerators •Cold room•Store room•Autoclave•Incubator•Fermentor•Bioreactor•Shipping Containers
Medical laboratory equipment calibration
As a full-service provider, Exova METECH is the single point of contact for all your instrument calibration, service and administration needs
On-site services
You can hire technical personnel for calibration and other metrological tasks, as a part of our full-service commitment to help you increase instru-ment utilisation and reduce production distur-bance or downtime.
The calibrations can be performed using our reference equipment and calibration methods or using your own reference equipment and rules.
Additional services
Our service for the Life Science industries also include•Metrological advice, e.g. measurement uncer-
tainty calculations or measuring instructions•Density measurements and flow in isolators•Determination of cell constants for conductivity
sensors•Geometrical measurement tasks
Delivering metrological confidence since 1947Exova METECH helps you achieve optimum on time instrument access at the right quality level.
We provide traceable and ISO/IEC 17025 accredited calibration of measurement instruments in Electrical, Dimensional and Physical parameters.
We are vendor independent and able to support all manufacturers and instrument types.
Our full-sercive commitment
As a full-service provider, Exova METECH is the single point of contact for all your instru-ment calibration, service and administration needs. Our services include•Requirement Analysis•Instrument Sourcing•Online Instrument Administration•Calibration•On-site services•Repair•Technical Support•Training•Divestment and Disposal
An outsourcing partner
Growing continuously through acquisitions and outsourcing partnerships since 1947, Exova METECH is the leading third party calibration and test & measurement service provider in Europe.
Key contact details
Sweden
T: +46 (0)10-480 46 50E: [email protected]
Denmark
T: +45 96 62 50 00E: [email protected]
Germany
T: +49 (0)40-52 95 61-0E: [email protected]
Finland
T: +358 (0)400 356 050E: [email protected]
www.exovametech.com/med Rev:
EM/M
ED4/
ENG
:12:
02
Exova METECH operates 18 facilities in Sweden, Denmark, Finland, Germany, Norway and on-site operations around the world.
Exova METECH is a part of Exova, one of the world’s leading groups committed to test and advise on the safety, quality and performance of our customers’ products and operations.
Exova operates 110 facilities in 22 countries, specialising in •Materials Technology•Metrology & Calibration•Fire Safety Technology•Chemistry & Microbiology
