HZVI Actuators Accessories

Limit switch

Features

- Independent installation of switches makes maintenance and replacement convenient.

- Firm and compact design Die-casting aluminum and plastic body

- Quick cam mechanism The cam i s fixed by springs can be set without need of tools and need no adjustment after the initial setting.

- Convenient for installation The NAMUR standard stainless steel shaft and bracket Reasonable design and convenient installation of the bracket connecting hole.

Specifications

Model BAPL-310 BAPL-410

Standard Option Standard Option

Protection Waterproof IP67 Waterproof IP67 Ex dII BT6

(EN50014/50018)

Shell material l Die-casting aluminum

Environment -25~85 ℃

Wiring end 2X1/2" NPT PT1/2"

PF1/2"

2X3/4"NPT PT3/4"

PF3/4"

Terminal Block 8 9~24 8 9~24 0~90 degree 0~180 degree 0~90 degree 0~180 degree

Position

indication Off: red On: yellow

Switch Mechanical switch Proximity switch Sensor switch

Position

Indication Unit 1k Ohm (0~5k Ohm ,0~10k Ohm)

Current feedback 4~20mA (20~4mA)

Model BAPL-210 BAPL-510

Standard Option Standard Option

Protection Waterproof IP67 IP68 Waterproof IP67 NEMA 4 4X

Shell material Die-casting aluminum Plastic

Environment -20~80 ℃ -15~80℃

Wiring end 2X1/2" NPT PT1/2"

PF1/2"

PGB.S

1/2"NPT

Terminal Block 8 points(0.08~0.25mm) Standard PCB 6 0~90 degree 0~180 degree 0~90 degree 0~180 degree

Position

indication Off: red On: yellow

Switch Mechanical switch X2

Proximity switch X2

Mechanical SPDT silver plated

Mechanical SPDT gold plated

Proximity NAMUR switch

Size Drawing

BAPL-310

BAPL-410

Size Drawing

BAPL-210

BAPL-510

Technical specification

Filter Regulator

Model

AFC2000

Ac2000

BFC3000

Bc2000

Working Medium

Air

Pull pipe bore

1/4"

3/8"

Filter element precision

40µm

Applicable pressure range

Manual drainage: 0.05~0.85Mpa

Max. adjustable pressure

0.95Mpa

Guaranteed pressure

1.5Mpa

Applicable temperature

5~60℃

Capacity filter cup

15CC

Capacity of oil feeding cup

25CC

Recommended lubricating oil

ISO VG32 or same level oil

Weight

0.7kg

0.5kg

0.7kg

Components

Filter

AF2000

AFR1500

AF3000

AFR2000

Pressure

regulating

valve

AR2000

AR3000

Oil feeder

AL2000

AL2000

AL3000

AL3000

Filter Regulator

Installation Please clean the connecting pipe and joint to avoid dust to enter gas circuit while installing. Please note whether the direction of gas flow is in accordance with arrow direction on the body and whether the gear form of connecting pipe and joint is correct or not. Fastness between filter, voltage regulating circuit (voltage regulating filter) and oil feeder: Match the bulge on stationary barrier with the groove on the body and then lock them up by stator and screw. Fastness while using high voltage valve and voltage regulating filter alone: circumvolve the fixed loop to lock the accessory stator tight.

Water discharging (filter) There are two modes for water discharging of the filter, automatic and manual. Manual: Water must be discharged before water level comes to filter element.

Voltage Regulation (Voltage Regulating Valve) Please draw back the rotary knob and then circumvolve it. Pressing the rotary knob means orientation. Turning the rotary knob right is to raise the exit pressure and turning the rotary knob left is to lower the exit pressure. While regulating the voltage, evenly adjust to the wanted pressure value step by step. It cannot be adjusted right the first time. Methods of oil feeding and Regulation of oil mass (oil Feeder) JISK2213 Transmission oil (ISO VG32 or same level oil) is applied for oil feeder. Oil mass should not be more than 80% of the cup. Number 0 is the minimum, 9 is the Maximum. The alignment point of number is arrow direction. It cannot be circumvolved from 9 to 0 position and It must be circumvolved clock wise.

Cautions Some accessories are made of PC material. It is not allowed to be near or used in any organic solvent. The PC cup must be cleaned by neutral detergent. Applying Voltage is not more than 0.95Mpa. Replace the filter element when the air flow at exit decreases obviously.

Solenoid Valve

Features The solenoid valve directly install the pneumatic actuators, only need to connect the air supply, save the pipe line connection. It adopt the same installing standard, it can connect with different bore solenoid and different factory’s solenoid valve.

Operating principle

Technical specifications - Change direction time (S): <0.05 - Pull Pipe thread: G1/2", G1/4", G1/8" - Resistance test pressure: 1.2MPa

2W511-0.8 2W512-0.8 2W511-10 2W512-10

2W521-0.8 2W522-0.8 2W521-10 2W522-10

Working medium Air (Filtered with 40µm filter screen )

Acting type Internal Pilot type

Positional

number 5/2 Channel or 3/2 channel

Effective cross-sectional

area 16mm2(CV=0.78) 30mm2(CV=1.68)

Pull pipe bore Air inlet=1/8" Air outlet=1/8" Air inlet=1/4" Air outlet=1/4"

lubrication No need

Using pressure 1.5~8.0kgf/cm2(21~114Psi)

Max 12Kgf/cm2(170.6Psi)

NUMAR STANDARD

5/2 channel 3/2 channel

Solenoid Valve

Technical specifications

Resistance

pressure

Working

temperature 5~60℃(41~140F)

Voltage range +_10%

Electricity

consumption AC:4.5VA DC:3.0W

Insulativity F class

Protection

class IP65(DIN40050)

Electrical

connection Terminal Type

The maximum

acting frequency 5 times/S

The shortest

Excitation Time 0.05S

Dimensions

Hong Kong (Headquarter) Flat 2108, 21F, CC WU Building 308, Hennessy Road Wan Chai - Hong Kong

Tel.: +852 3568 2257 Fax: +852 2125 4982

info@hzvivalve.com General Enquiries sales@hzvivalve.com Sales Enquires certificates@hzvivale.com Certificates Wenzhou - Zhejiang - P.R. China

Gongye 2nd Road Yongjia, Wenzhou, Zhejiang, P.R. China Shijiazhuang - Hebei - P.R. China

308 National Road Ningjin, Xingtai, Hebei, P.R. China