Upload
others
View
11
Download
1
Embed Size (px)
Citation preview
AC370WLWoodturning Lathe
Code 105116Original Instructions
AT: 01/10/2020BOOK REF: 105185
BOOK VERSION: 02
Index of Contents
2
EU Declaration of Conformity
Specification Model AC370WL Rating Craft Power 750W Speed 500-2,000rpm Spindle Taper 2MT Spindle Thread 1” x 8tpi (ref T04M) Taper Tailstock 2MT Distance Between Centres 1,100mm (43.3”) Max Diameter over Bed 370mm Tool Rest Stem Diameter 25mm Overall L x W x H 1,680 x 470 x 1,155mm Weight 97kg
The symbols below advise the correct safety procedures when using this machine.
Fully read manualand safety instructions
before use
Eye protectionshould be worn
Ear protectionshould be worn
HAZARDDust maskshould be worn
EU Declaration of Conformity 02Specification 02General Safety Rules 03-04Specific Safety Rules for Wood Lathes 05-06Electrical Information 06-07Know your Wood Lathe 08Unpacking Contents 9Assembly 10-11Adjustments 12Operation 13-14Maintenance 14-15Exploded Diagrams/Lists 16-17
Cert No: MC1100
Axminster Tool Centre LtdAxminster Devon EX13 5PH UK
axminstertools.com
Type Lathe (Wood Lathe)
Model AC370WL conforms to the machinery example for which the EC Type-Examination Certificate No AE 50390140, AE 50398334, AM 50307837, AN 50170711has been issued by Laizhou Planet Machinery Co., Ltd.at: Yutai West Street Laizhou, Shandong 261400 China
and complies with the relevant essential health and safety requirements.
2006/42/EC2006/95/EC - Annex IEN 55014-1:2017 EN 55014-2:2015
declares that the machinery described:-
This machine complies with the following directives:
EU Declaration of Conformity
EN 61000-3-2:2014 EN 61000-3-3:2013 EN 55014-1:2006+A1+A2 EN 55014-2:1997+A1+A2
Signed
Andrew ParkhouseOperations Director Date: 22/01/2018
General Safety Rules
3
General Safety Rules
4
Specific Safety Rules for Wood Lathes
5
Specific Safety Rules for Wood Lathes
6
Electrical Information
Electrical Information
7
Know your Wood Lathe
8
Unpacking Contents
9
Assembly
10
Assembly
11
Adjustments
12
Operation
13
Operation
14
Maintenance
Maintenance
15
Lubricating the drive shaft
Over time the spindle drive on the Variomatic’ speed control assembly will need lubricating to prevent the moving pulleys from seizing. It is recommend to check and lubricate the shaft on a regular basis.
1) Remove the four dome head screws holding the head stock cover in place. Remove cover, clean the pulley mechanism and remove any build up resin debris. Use a push type grease gun for chainsaw sprocket nose guide bar. Place it over the grease nipple to the end of the motor drive shaft & pump in grease several time until you see it emage over spring assembly. Re-fit the cover and secure in place.
Remove the four dome screws holding the cover
Grease gun for chainsaw sprocket nose guide bar
1
3
4
5
2 Pump grease into the shaft serveral times, you will see grease emerge from the spring.
2) Spray ambersil PTFE film anti-stick over the lathes spindle shaft & Swivel mechanisum this will help toreduce friction and to help prevent it from corroding.
PUMP Grease into shaft
Grease nipple
Exploded Diagrams/Lists
16
Exploded Diagrams/Lists
17
NO. DESCRIPTION Q’TY
1 HEADSTOCK 1
2 FACEPLATE 1
3 HEADSTOCK SPUR 1
4 SPINDLE 1
5 KEY 1
6 BEARING 2
7 “C”RING 2
8 SPRING 1
9 BRACKET-SHIFTING LEVER 1
10 “CRING 1
11 “C”RING 1
12 “CRING 1
13 MOTOR 1
14 KEY 1
15 SCREW 1
16 COVER-MOTOR 1
17 PULLEY-MOTOR(RIGHT) 1
18 PULLEY-MOTOR(LEFT) 1
19 SPRING 1
20 SLEEVE 1
21 “CRING 2
22 PUSH-OUT ROD 1
23 LEVER 1
24 “CRING 3
25 ECCENTRIC ROD 1
26 SCREW 1
27 “CRING 1
28 PULLEY-SPINDLE(LEFT) 1
29 V-BELT 1
30 PULLEY-SPINDLE(RIGHT) 1
31 BEARING 1
32 NUT-LOCK 1
33 NUT 9
34 CLAMP 2
35 NUTM4 2
36 “CRING 1
37 TURNING BASE 1
38 BED 1
39 BAFFLE 2
40 SCREW 4
41 HEX WRENCH 4
42 BOLT-A 1
43 CLAMP-A 1
44 HEX NUT 3
45 ANGULAR SETTING ASSEMBLY 1
46 SCREW 2
47 SPRING WASHER 2
48 GEAR ASSEMBLY 1
49 SPEED LABLE 1
51 HEX SCREW 3
52 BACK 1
53 BOLT-B 2
54 CLAMP-B 2
55 ECCENTRIC ROD 1
56 TOOL REST BODY 1
57 HANDLE ASSEMBLY 2
58 EXTENSION TOOL REST 1
59 LOCK HANDLE-TAILSTOCK 1
60 TOOL REST 1
61 TAILSTOCK SPUR 1
62 TAIL SPINDLE 1
63 TAIL STOCK SCREW 1
64 HANDLE ASSEMBLY 1
65 TAILSTOCK 1
66 WASHER 1
67 HANDLE WHEEL 1
68 SCREW 1
69 SCREW 1
70 SWITCH BOX 1
71 SWITCH 1
72 SWITCH BOX PLATE 1
73 SCREW 2
74 COVER 1
75 SPRING WASHER 8
76 POWER CORD 1
77 MOTOR POWER WIRE 1
78 NUT 20
79 WASHER 20
80 CARRIAGE BOLT STAND 20
81 STAND UPPER COVER 2
82 STAND LEG--I 2
83 STAND LEG--II 2
84 TOOL TABLE 1
The packaging is suitable for recycling. Please dispose of it in a responsible manner.
Do not dispose of electric tools together with household waste material. By law they must be collected and recycled separately.
EU Countries Only
The Axminster guarantee
Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years!
For more information visit axminstertools.com/3years
Axminster Tools, Axminster Devon EX13 5PH
axminstertools.com