AC-036045001 990L

DELETED DETAIL 7

DETAILS

STD. DWG.

AC-036045 001L990

11 APR91 ASC DRAWING REINSTATED &

CADDED PER CSD REQUEST

ACCEPTABLE SPECIFICATION LISTS.

REFERENCE DRAWINGS

STD. HEAVY WELDING BOSS

STD. HEAVY WELDING BOSS

STD. SAMPLE TUBE

SOCKET WELD

AE-036175

AE-036046

AE-036643

4. FLANGED VALVES ARE REQUIRED FOR CONNECTION

5. CHECK APPROPRIATE ANSI CODE TO DETERMINE

POSSIBLE NEED FOR FULL CIRCUMFERENTIAL

REINFORCEMENT OF OUTLETS 2 INCH OR OVER.

SIZES TO USE WITH BOSSES.

BE IN LINE WITH PIPE RUN IN DET. 1, 2, 4, 5 & 6.

7. VALVES STEM ORIENTATION IS PREFERRED TO

SEAL WELD TO

FILL SPACE

BETWEEN BOSS

AND VALVE

SEAL WELD TO

FILL SPACE

BETWEEN BOSS

AND VALVE

DETAIL-1

DETAIL-4

DETAIL-2

BRIDGE WELD

SEAL WELD

SAMPLE TUBE

SEE DWG.

AE-036046

1/2 " GLOBE

VALVE

DETAIL-5

C

C C

C

C

C

C

C

C

C

BRIDGE WELD

C

C

DETAIL-3

REINFORCING

PAD

WELDING NECK

FLANGE

GATE VALVE

BLIND

FLANGE

75mm

(3")

1/2 " SAMPLE CONNECTION

DETAIL-6

4.6 TO 14.1 (161 TO 500)

14.2 TO 34.0 (501 TO 1200)

1

1 1/2

2

3

INCHESm 3 (FT )3

PIPE VOLUME DRAIN SIZE

0 TO 4.5 (0 TO 160)

34.1 AND

ABOVE

(1201) AND

ABOVE

1/2 " WELDING

BOSS TYPE II

VENT, DRAIN & SAMPLE CONNECTIONS

6. SEE STANDARD DRAWING AE-036175 FOR DRILL

TYPICAL INSTALLATION DRAWING PIPE PLUG

NIPPLE, CLOSE

WELDING BOSS

POINT IN LINE

GATE VALVE

WELDING BOSS

IN LINE

GATE VALVE

NIPPLE, CLOSE

PIPE PLUG GATE VALVE

WELDING BOSS

TYPE II AT HIGH

POINT IN LINE

(SEE NOTES 2 & 3)(SEE NOTES 2 & 3)

GATE VALVE

WELDING BOSS

AT HIGH POINT

IN LINE

VENT (1 1/2 " & BELOW) VENT (1 1/2 " & BELOW)

(SEE NOTES 2 & 3)

(SEE NOTES 2 & 3)

AT LOW POINT

TYPE II AT LOW

DRAIN (2" & ABOVE)

3. WHEN DETAIL 1 & 4 ARE USED IN THE

VICINITY OF PUMPS OR CONTROL VALVES,

ADDITIONAL BRACING MAY BE REQUIRED.

USE WELDED BONNET VALVES.

USE OS &Y VALVES WITH BOLTED BONNETS.

DRAIN (1 1/2 " & BELOW)

DRAIN (1 1/2 " & BELOW)

2. DETAILS 2 & 5 WITH EXTENDED BODY

VALVES ARE PREFERRED OVER DETAILS 1 &4.

2 INCH OR LARGER. THEY MAY ALSO BE USED

FOR SMALLER OUTLETS.

12 DEC92 ELT

ESSD

ORIGINAL

SIGNED

ORIGINAL

SIGNED

ORIGINAL

SIGNED

1. MATERIALS SHALL CONFORM WITH SAUDI ARAMCO

NONE

1414

ENGINEERING STANDARDS. SEE SAES-L-105 FOR

13 05/06 MSM REVISED NOTES MASHMM

(SEE NOTE 8)

8. SAMPLE PROBES TO BE LOCATED ON TOP OF

PIPE FOR GAS SAMPLING ( API MPMS 14,1,7,4,2 )

AND ON THE SIDE FOR LIQUID SAMPLING

04/10 MSM REVISED NOTES14

(API MPMS 8,2,10,4 ) .

PLANT NO.INDEXREV. NO. DRAWING NUMBERSHT. NO.

THIS DRAWING IS NOT TO BE USED FOR

CONSTRUCTION OR FOR ORDERING

MATERIAL UNTIL CERTIFIED AND DATED

PLANT NO. INDEX REV. NO.DRAWING NUMBER SHT. NO.

CERTIFIED

BY DATE

DRAWN BY

DATE STARTED

OPR’G. DEPT.

APP’D FOR CONSTR.

CHECKED BY SCALE

DATE COMPLETED

ENG. DEPT.

DATE BY JO/EWO DESCRIPTION CHKD. CERT. APPD.REV.

NO.

NOTES:

OIL COMPANYSAUDI ARABIAN

CADD-02

Saudi Aramco 2635 ENG. (3/91)