AABTLAC0 - course.sdu.edu.cncourse.sdu.edu.cn/G2S/eWebEditor/uploadfile/20130529170733008.pdf · Caption: Anchor Bracket. ... ( apart) and complete auxiliary view of entire object

©2004 by Prentice Hall, Inc.A Pearson Company

Figure Number: 08-01 a,b GieseckeEngineering Graphics, 8ECaption: Regular Views and Auxiliary Views.

AABTLAC0


Figure Number: 08-02 a-c GieseckeEngineering Graphics, 8ECaption: An Auxiliary View.

AABTLAD0


Figure Number: 08-03 1-4 GieseckeEngineering Graphics, 8ECaption: Drawing an Auxiliary View—Folding-Line Method.

AABTLAE0


Figure Number: 08-04 GieseckeEngineering Graphics, 8ECaption: Drawing Parallel or Perpendicular Lines.

AABTLAF0


Figure Number: 08-05 a-c GieseckeEngineering Graphics, 8ECaption: Position of the Reference Plane.

AABTLAG0


Figure Number: 08-06 a 1-5 GieseckeEngineering Graphics, 8ECaption: Drawing an Auxiliary View—Reference-Plane Method.

AABTLAH0


Figure Number: 08-07 a-c GieseckeEngineering Graphics, 8ECaption: Depth Auxiliary Views.

AABTLAI0


Figure Number: 08-08 a-c GieseckeEngineering Graphics, 8ECaption: Height Auxiliary Views.

AABTLAJ0


Figure Number: 08-09 a-c GieseckeEngineering Graphics, 8ECaption: Width Auxiliary Views.

AABTLAK0


Figure Number: 08-10 a,b GieseckeEngineering Graphics, 8ECaption: Revolving a Drawing.

AABTLAL0


Figure Number: 08-11 a-c GieseckeEngineering Graphics, 8ECaption: Dihedral Angles.

AABTLAM0


Figure Number: 08-12 a,b GieseckeEngineering Graphics, 8ECaption: Plotted Curves.

AABTLAN0


Figure Number: 08-13 a,b GieseckeEngineering Graphics, 8ECaption: Reverse Construction.

AABTLAO0


Figure Number: 08-14 a-c GieseckeEngineering Graphics, 8ECaption: Primary Auxiliary Views.

AABTLAP0


Figure Number: 08-15 a-c GieseckeEngineering Graphics, 8ECaption: Partial Views.

AABTLAQ0


Figure Number: 08-16 GieseckeEngineering Graphics, 8ECaption: Half Views.

AABTLAR0


Figure Number: 08-17 a-c GieseckeEngineering Graphics, 8ECaption: Auxiliary Sections.

AABTLAS0


Figure Number: 08-18 GieseckeEngineering Graphics, 8ECaption: Auxiliary Section.

AABTLAT0


Figure Number: 08-19 GieseckeEngineering Graphics, 8ECaption: Auxiliary Section.

AABTLAU0


Figure Number: 08-20 GieseckeEngineering Graphics, 8ECaption: True Length of a Line by Means of an Auxiliary View.

AABTLAV0


Figure Number: 08-21 GieseckeEngineering Graphics, 8ECaption: Successive Auxiliary Views.

AABTLAW0


Figure Number: 08-22 1-3 GieseckeEngineering Graphics, 8ECaption: True Size of Oblique Surface—Folding-Line Method.

AACXFIK0


Figure Number: 08-23 a,b GieseckeEngineering Graphics, 8ECaption: True Size of an Oblique Surface—Reference-Plane Method.

AABTLAY0


Figure Number: 08-24 GieseckeEngineering Graphics, 8ECaption: Secondary Auxiliary View with Oblique Direction of Sight Given.

AABTLAZ0


Figure Number: 08-25 GieseckeEngineering Graphics, 8ECaption: Secondary Auxiliary View—Partial Views.

AABTLBA0


Figure Number: 08-26 a,b GieseckeEngineering Graphics, 8ECaption: Ellipses.

AABTLBB0


Figure Number: 08-27 GieseckeEngineering Graphics, 8ECaption: "RH Finger. Given: Front and auxiliary views. Required: Complete front, auxiliary, left-side, and top views (Layout A–3 or A4–3 adjusted). "

AABTLBC0


Figure Number: 08-28 GieseckeEngineering Graphics, 8ECaption: "V-Block. Given: Front and auxiliary views. Required: Complete front, top, and auxiliary views (Layout A–3 or A4–3 adjusted). "

AABTLBD0

1 2 3 4 5 6

7 8 9 10 11

12

13 1415 16

1817

19 20 21 22 23 24

25 26 2728 29

30


Figure Number: 08-29 1-30 GieseckeEngineering Graphics, 8ECaption: "Auxiliary View Problems. Make freehand sketch or instrument drawing of selected problem as assigned. Draw given front and right-side views, and add incompleteauxiliary view, including all hidden lines (Layout A–3 or A4–3 adjusted). If assigned, design your own right-side view consistent with given front view, and then add com-plete auxiliary view. "

AACXFIL0


Figure Number: 08-30 GieseckeEngineering Graphics, 8ECaption: Anchor Bracket. Draw necessary views or partial views (Layout A–3 or A4–3 adjusted).

AACXFIM0


Figure Number: 08-31 GieseckeEngineering Graphics, 8ECaption: "Centering Block. Draw complete front, top, and right-side views, plus indicated auxiliary views (Layout B–3 or A3–3). "

AABTLBG0


Figure Number: 08-32 GieseckeEngineering Graphics, 8ECaption: Clamp Slide. Draw necessary views completely (Layout B–3 or A3–3).

AABTLBH0


Figure Number: 08-33 GieseckeEngineering Graphics, 8ECaption: Anchor Bracket. Draw necessary views or partial views (Layout A–3 or A4–3 adjusted).

AABTLBI0


Figure Number: 08-34 GieseckeEngineering Graphics, 8ECaption: "Centering Block. Draw complete front, top, and right-side views, plus indicated auxiliary views (Layout B–3 or A3–3). "

AACXFIN0


Figure Number: 08-35 GieseckeEngineering Graphics, 8ECaption: Clamp Slide. Draw necessary views completely (Layout B–3 or A3–3).

AABTLBK0


Figure Number: 08-36 GieseckeEngineering Graphics, 8ECaption: "Rod Guide. Draw necessary views, including complete auxiliary view showing true shape of upper rounded portion (Layout B–4 or A3–4 adjusted). "

AABTLBL0


Figure Number: 08-37 GieseckeEngineering Graphics, 8ECaption: "Brace Anchor. Draw necessary views, including partial auxiliary view showing true shape of cylindrical portion (Layout B–4 or A3–4 adjusted). "

AABTLBM0


Figure Number: 08-38 GieseckeEngineering Graphics, 8ECaption: "45° Elbow. Draw necessary views, including a broken section and two half views of flanges (Layout B–4 or A3–4 adjusted). "

AABTLBN0


Figure Number: 08-39 GieseckeEngineering Graphics, 8ECaption: "Angle Guide. Draw necessary views, including a partial auxiliary view of cylindrical recess (Layout B–4 or A3–4 adjusted). "

AABTLBO0


Figure Number: 08-40 GieseckeEngineering Graphics, 8ECaption: Holder Block. Draw front and right-side views ( apart) and complete auxiliary view of entire object showing true shape of surface A and all hidden lines (LayoutA–3 or A4–3 adjusted).

AABTLBP0


Figure Number: 08-41 GieseckeEngineering Graphics, 8ECaption: "Control Bracket. Draw necessary views, including partial auxiliary views and regular views (Layout C–4 or A2–4). "

AABTLBQ0


Figure Number: 08-42 GieseckeEngineering Graphics, 8ECaption: "Tool Holder Slide. Draw given views, and add complete auxiliary view showing true curvature of slot on bottom (Layout B–4 or A3–4 adjusted). "

AABTLBR0


Figure Number: 08-43 GieseckeEngineering Graphics, 8ECaption: "Adjuster Block. Draw necessary views, including complete auxiliary view showing true shape of inclined surface (Layout B–4 or A3–4 adjusted). "

AACXFIO0


Figure Number: 08-44 GieseckeEngineering Graphics, 8ECaption: "Tool Holder Slide. Draw given views, and add complete auxiliary view showing true curvature of slot on bottom (Layout B–4 or A3–4 adjusted). "

AABTLBT0


Figure Number: 08-45 GieseckeEngineering Graphics, 8ECaption: "Adjuster Block. Draw necessary views, including complete auxiliary view showing true shape of inclined surface (Layout B–4 or A3–4 adjusted). "

AABTLBU0


Figure Number: 08-46 GieseckeEngineering Graphics, 8ECaption: Brake Control Lever. Draw necessary views and partial views (Layout B–4 or A3–4 adjusted).

AABTLBV0


Figure Number: 08-47 GieseckeEngineering Graphics, 8ECaption: "Shifter Fork. Draw necessary views, including partial auxiliary view showing true shape of inclined arm (Layout B–4 or A3–4 adjusted). "

AABTLBW0


Figure Number: 08-48 GieseckeEngineering Graphics, 8ECaption: Cam Bracket. Draw necessary views or partial views as needed. (Layout B–4 or A3–4 adjusted).

AACXFIP0


Figure Number: 08-49 GieseckeEngineering Graphics, 8ECaption: "RH Tool Holder. Draw necessary views, including partial auxiliary views showing 105° angle and square hole true size. (Layout B–4 or A3–4 adjusted). "

AABTLBY0


Figure Number: 08-50 GieseckeEngineering Graphics, 8ECaption: "Draw secondary auxiliary views, complete, which (except Prob. 2) will show the true sizes of the inclined surfaces. In Prob. 2 draw secondary auxiliary view asseen in direction of arrow (Layout B–3 or A3–3). "

AABTLBZ0


Figure Number: 08-51 GieseckeEngineering Graphics, 8ECaption: Control Bracket. Draw necessary views including primary and secondary auxiliary views so that the latter shows true shape of oblique surface A (Layout B–4 orA3–4 adjusted).

AABTLCA0


Figure Number: 08-52 GieseckeEngineering Graphics, 8ECaption: Holder Block. Draw given views and primary and secondary auxiliary views so that the latter shows true shape of oblique surface (Layout B–4 or A3–4 adjusted).

AACXFIQ0


Figure Number: 08-53 GieseckeEngineering Graphics, 8ECaption: "Dovetail Slide. Draw complete given views and auxiliary views, including view showing true size of surface 1–2–3–4 (Layout B–4 or A3–4 adjusted). "

AABTLCC0


Figure Number: 08-54 GieseckeEngineering Graphics, 8ECaption: Dovetail Guide. Draw given views plus complete auxiliary views as indicated (Layout B–4 or A3–4 adjusted).

AABTLCD0


Figure Number: 08-55 GieseckeEngineering Graphics, 8ECaption:

AABTLCE0


Figure Number: 08-56 GieseckeEngineering Graphics, 8ECaption: Adjustable Stop. Draw complete front and auxiliary views plus partial right-side view. Show all hidden lines (Layout C–4 or A2–4).

AABTLCF0


Figure Number: 08-57 GieseckeEngineering Graphics, 8ECaption: Box Tool Holder for Turret Lathe. Given: Front and right-side views. Required: Front and left-side views and complete auxiliary view as indicated by arrow (LayoutC–4 or A2–4).

AABTLCG0


Figure Number: 08-58 GieseckeEngineering Graphics, 8ECaption: Pointing Tool Holder for Automatic Screw Machine. Given: Front and right-side views. Required: Front view and three partial auxiliary views (Layout C–4 orA2–4).

AABTLCH0

R 1.25R 1.00

2xR.875 2xØ.875

Ø 1.25

4.00

2.75

5.50


Figure Number: 08-59 GieseckeEngineering Graphics, 8ECaption: "Print Roller. Given: Right-side view. Design your own front and auxiliary view (Use Layout A–3 or A4–3 adjusted). If assigned, use CAD to create a partial auxil-iary view."

AACXFIR0

FRON

T VIEW

45°

.38

R.75TYP.

2.5

1.0

2X:.6

8TH

RU


Figure Number: 08-60 GieseckeEngineering Graphics, 8ECaption: Clamp. Draw all required views. Include at least one auxiliary view (Layout A–3 or A4–3 adjusted).

AACXFIS0

FRON

TVIE

W

2.00

3.50

60°

1.751.25

.50

.50


Figure Number: 08-61 GieseckeEngineering Graphics, 8ECaption: Plastic Slide. Draw all required views. Include at least one auxiliary view (Layout A–3 or A4–3 adjusted).

AACXFIV0

R.62

1.25.62

(2.43)

R.28

R.56

.06

.12

:.62THRU

1.12

.50

0.6

FRON

TVIE

W

1.50

1.0R.21

R.50

.50

1.0

32°


Figure Number: 08-62 GieseckeEngineering Graphics, 8ECaption: Mounting Clip. Draw all required views. Include at least one auxiliary view (Layout A–3 or A4–3 adjusted).

AACXFIW0

Documents

AABTLAC0 - course.sdu.edu.cncourse.sdu.edu.cn/G2S/eWebEditor/uploadfile/20130529170733008.pdf · Caption: Anchor Bracket. ... ( apart) and complete auxiliary view of entire object