Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
The InvisiWeld Fastening System uses advanced technology to mechanically install
UltraPly™ TPO roofs without fasteners penetrating the roofing membrane. This
results in labor and materials savings, increased wind uplift resistance and a more
balanced load distribution across the roof.
• Plates are bonded to the underside of the membrane via induction heating
• Welds UltraPly TPO membrane to TPO coated InvisiWeld plate in seconds
• Required 25–50% fewer fasteners compared to conventional mechanically fastened TPO systems
Custom ACCessoriesNo two roofs are the same. If your roof has unique designs or elements, customized UltraPly TPO accessories from Firestone offer the same money-saving
benefits of our standard UltraPly TPO accessories and give you the confidence of knowing you’re getting quality accessories from a company you trust.
Pipe boots:
• Round, square or conical shaped
• Available with closed or split design
Custom Curb flashing:
• Allows for square or rectangular configurations Pipe Boot Conical Boot Square Tube Boot Curb Flashing
All Firestone custom accessories come with factory-formed welds and are fabricated from proven UltraPly TPO reinforced membrane.
the invisiWeld™ FAstening system
A C C e s s o r y l i n e
©2010 Firestone Building Products Printed in U.S.A. Item #1179 9/10 (replaces 8/09)-01
www.firestonebpco.comNote: This brochure is meant only to highlight Firestone’s products and specifications. Information is subject to change without notice. All products and specifications are
listed in approximate weights and measurements. For complete product and detail information, please refer to the appropriate Technical Manual. Firestone takes responsibility for furnishing quality materials which meet Firestone’s published product specifications. As neither Firestone itself nor its representatives practice architecture, Firestone offers no opinion on, and expressly disclaims any responsibility for, the soundness of any structure on which its products may be applied. If questions arise as to the soundness of a structure
or its ability to support a planned installation properly, the Owner should obtain opinions of competent structural engineers before proceeding. Firestone accepts no liability for any structural failure or for resultant damages, and no Firestone Representative is authorized to vary this disclaimer.
Firestone Building Products
250 West 96th St., Indianapolis, IN 46260
Corporate Office: 1-800-428-4442 • 317-575-7000 • Fax: 317-575-7100
international offices:
Firestone Building Products Canada
2835 Argentia Rd., Unit #2
Mississauga, ON L5N 8G6
1-888-292-6265 • 905-363-3150
Fax: 877-666-3022
Firestone Building Products Europe
Ikaroslaan 75 — 1930 Zaventem, Brussels, Belgium
+32 2 7114450 • Fax: +32 2 7212718
Firestone Building Products Latin America
8200 NW 52nd Terrace, Suite #107
Miami, FL 33166
305-471-0117 • Fax: 305-471-0377
MANUFACTURED WITH 100% WIND ENERGY
www.hardingpoorman.comHPG Uses 100% Green Power.
This green document printed on recycled paper using Soy Inks and manufactured using 100% Wind Power.
QuiCkseAm™
ultraPly™ tPo Quickseam 5.5" & 9.5" Flashing• Can be used as coverstrips over intermediate mechanical attachment, or at metal edge
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rmA strip• Non-penetrating intermediate attachment for roof perimeters
• Allows the use of membranes up to 12' for perimeter installations
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rPF strip• Non-penetrating membrane attachment for securement at angle changes
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam Pipe Boots• Covers pipes ranging from 1" to 6" diameter
• No heat welding required
• Pre-applied QuickSeam pressure-sensitive tape technology
singlePly QuickPrime™ Primer• Designed to clean and prime UltraPly TPO to receive all QuickSeam accessories
• Also available in low VOC version, UltraPly TPO QuickPrime LVOC Primer
other ACCessories
ultraPly tPo Premium Walkway Pads• 30" wide by 50' long rolls in light gray color
• Protects UltraPly membrane in traffic areas and around rooftop equipment
ultraPly tPo Coated metal
• Non-reinforced UltraPly TPO factory laminated to 24-guage hot-dipped galvanized steel
• For use as a flashing component for UltraPly TPO systems
• 4' x 10' sheets available in white, tan and gray
ultraPly tPo reel-Fast™ Collated seam Plates
• Specifically designed for use in the attachments of UltraPly TPO systems over steel, wood or concrete decks
• Reel includes cardboard flanges to assist in unrolling plates onto the membrane
• Available with plates spaced at 6" or 12" on center
• Can be used with Firestone Heavy Duty or All-Purpose fasteners
Pre-Formed ACCessories
ultraPly™ tPo reinforced split Pipe Boots• 3 sizes available
• Available in white, tan and gray
• Split design to fit pipe penetrations with limited or no access from above
ultraPly tPo Pipe Boots• Available in white, tan and gray
• Universal Boots fit pipes from 1" to 6"
• Large Boot fits 6" to 8"
ultraPly tPo reinforced Curb Corners• Fabricated from 45 mil thick UltraPly TPO
• Available in 6 sizes to accommodate various curb sizes
ultraPly tPo inside/outside Corners• Specifically designed for flashing either inside or outside corners
on curbs, parapets and scuppers
ultraPly tPo t-Joint Covers• Designed to cover and seal T-Joints formed at seam intersections
memBrAne
ultraPly tPo unsupported Flashing
• Non-reinforced TPO for field fabrication of special details
• Available in white, tan and gray
ultraPly tPo 18" supported Flashing
• Specifically designed for curbs and parapet walls
• One edge is encapsulated, eliminating the need for cut-edge sealant
• Available in 50¹ rolls
ultraPly tPo 8" Cover strips
• Constructed of 60 mil thick UltraPly TPO
• 50’ length, pre-cut & ready to roll
• Available in white, tan and gray
Greater energy efficiency and a great value make thermoplastic polyolefin (TPO)
the fastest growing sustainable commercial roofing product available. Firestone
ultraPly™ tPo provides a heritage of excellence combined with the exclusive
Red Shield® warranty for a roof that delivers on quality and long-term perfor-
mance. And now, our complete line of UltraPly TPO accessories provides faster
installation, lower system costs and watertight seals around any roof protrusion.
A t o t A l t P o s o l u t i o n F r o m t h e B r A n d y o u t r u s t
Adhesives
ultraPly Bonding Adhesive• Specifically designed to bond
UltraPly TPO membrane to wood, metal, masonry and other substrates
ultraPly tPo Xr Bonding Adhesive• Specifically designed for use with
UltraPly TPO XR (fleece-backed) membrane
• Labor-saving, one-side-only application
• Applies with most standard application methods
ultraPly tPo Cut-edge sealant• Used to seal cut edges of membrane
where polyester reinforcement is exposed
• Available in white, tan and gray
ultraPly tPo general Purpose sealant• High-quality sealant with excellent
adhesion to a variety of surfaces
• Can be used as a fastener sealer, termination bar caulk and/or TPO cut-edge treatment
seAlAnts
Water Based Bonding Adhesive s• Water-based alternative to traditional
solvent-based adhesives
single-Ply lvoC Bonding Adhesive 1168• Formulated for special
low-VOC applications
• Complies with SCAQMD and LEED® requirements
single-Ply lvoC Bonding Adhesive• Faster dry time than competitive
solvent-based products
• Can be applied in cold weather, unlike water-based adhesives
lvoC Adhesives
QuiCkseAm™
ultraPly™ tPo Quickseam 5.5" & 9.5" Flashing• Can be used as coverstrips over intermediate mechanical attachment, or at metal edge
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rmA strip• Non-penetrating intermediate attachment for roof perimeters
• Allows the use of membranes up to 12' for perimeter installations
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rPF strip• Non-penetrating membrane attachment for securement at angle changes
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam Pipe Boots• Covers pipes ranging from 1" to 6" diameter
• No heat welding required
• Pre-applied QuickSeam pressure-sensitive tape technology
singlePly QuickPrime™ Primer• Designed to clean and prime UltraPly TPO to receive all QuickSeam accessories
• Also available in low VOC version, UltraPly TPO QuickPrime LVOC Primer
other ACCessories
ultraPly tPo Premium Walkway Pads• 30" wide by 50' long rolls in light gray color
• Protects UltraPly membrane in traffic areas and around rooftop equipment
ultraPly tPo Coated metal
• Non-reinforced UltraPly TPO factory laminated to 24-guage hot-dipped galvanized steel
• For use as a flashing component for UltraPly TPO systems
• 4' x 10' sheets available in white, tan and gray
ultraPly tPo reel-Fast™ Collated seam Plates
• Specifically designed for use in the attachments of UltraPly TPO systems over steel, wood or concrete decks
• Reel includes cardboard flanges to assist in unrolling plates onto the membrane
• Available with plates spaced at 6" or 12" on center
• Can be used with Firestone Heavy Duty or All-Purpose fasteners
Pre-Formed ACCessories
ultraPly™ tPo reinforced split Pipe Boots• 3 sizes available
• Available in white, tan and gray
• Split design to fit pipe penetrations with limited or no access from above
ultraPly tPo Pipe Boots• Available in white, tan and gray
• Universal Boots fit pipes from 1" to 6"
• Large Boot fits 6" to 8"
ultraPly tPo reinforced Curb Corners• Fabricated from 45 mil thick UltraPly TPO
• Available in 6 sizes to accommodate various curb sizes
ultraPly tPo inside/outside Corners• Specifically designed for flashing either inside or outside corners
on curbs, parapets and scuppers
ultraPly tPo t-Joint Covers• Designed to cover and seal T-Joints formed at seam intersections
memBrAne
ultraPly tPo unsupported Flashing
• Non-reinforced TPO for field fabrication of special details
• Available in white, tan and gray
ultraPly tPo 18" supported Flashing
• Specifically designed for curbs and parapet walls
• One edge is encapsulated, eliminating the need for cut-edge sealant
• Available in 50¹ rolls
ultraPly tPo 8" Cover strips
• Constructed of 60 mil thick UltraPly TPO
• 50’ length, pre-cut & ready to roll
• Available in white, tan and gray
Greater energy efficiency and a great value make thermoplastic polyolefin (TPO)
the fastest growing sustainable commercial roofing product available. Firestone
ultraPly™ tPo provides a heritage of excellence combined with the exclusive
Red Shield® warranty for a roof that delivers on quality and long-term perfor-
mance. And now, our complete line of UltraPly TPO accessories provides faster
installation, lower system costs and watertight seals around any roof protrusion.
A t o t A l t P o s o l u t i o n F r o m t h e B r A n d y o u t r u s t
Adhesives
ultraPly Bonding Adhesive• Specifically designed to bond
UltraPly TPO membrane to wood, metal, masonry and other substrates
ultraPly tPo Xr Bonding Adhesive• Specifically designed for use with
UltraPly TPO XR (fleece-backed) membrane
• Labor-saving, one-side-only application
• Applies with most standard application methods
ultraPly tPo Cut-edge sealant• Used to seal cut edges of membrane
where polyester reinforcement is exposed
• Available in white, tan and gray
ultraPly tPo general Purpose sealant• High-quality sealant with excellent
adhesion to a variety of surfaces
• Can be used as a fastener sealer, termination bar caulk and/or TPO cut-edge treatment
seAlAnts
Water Based Bonding Adhesive s• Water-based alternative to traditional
solvent-based adhesives
single-Ply lvoC Bonding Adhesive 1168• Formulated for special
low-VOC applications
• Complies with SCAQMD and LEED® requirements
single-Ply lvoC Bonding Adhesive• Faster dry time than competitive
solvent-based products
• Can be applied in cold weather, unlike water-based adhesives
lvoC Adhesives
QuiCkseAm™
ultraPly™ tPo Quickseam 5.5" & 9.5" Flashing• Can be used as coverstrips over intermediate mechanical attachment, or at metal edge
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rmA strip• Non-penetrating intermediate attachment for roof perimeters
• Allows the use of membranes up to 12' for perimeter installations
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam rPF strip• Non-penetrating membrane attachment for securement at angle changes
• Pre-applied QuickSeam pressure-sensitive tape technology
ultraPly Quickseam Pipe Boots• Covers pipes ranging from 1" to 6" diameter
• No heat welding required
• Pre-applied QuickSeam pressure-sensitive tape technology
singlePly QuickPrime™ Primer• Designed to clean and prime UltraPly TPO to receive all QuickSeam accessories
• Also available in low VOC version, UltraPly TPO QuickPrime LVOC Primer
other ACCessories
ultraPly tPo Premium Walkway Pads• 30" wide by 50' long rolls in light gray color
• Protects UltraPly membrane in traffic areas and around rooftop equipment
ultraPly tPo Coated metal
• Non-reinforced UltraPly TPO factory laminated to 24-guage hot-dipped galvanized steel
• For use as a flashing component for UltraPly TPO systems
• 4' x 10' sheets available in white, tan and gray
ultraPly tPo reel-Fast™ Collated seam Plates
• Specifically designed for use in the attachments of UltraPly TPO systems over steel, wood or concrete decks
• Reel includes cardboard flanges to assist in unrolling plates onto the membrane
• Available with plates spaced at 6" or 12" on center
• Can be used with Firestone Heavy Duty or All-Purpose fasteners
Pre-Formed ACCessories
ultraPly™ tPo reinforced split Pipe Boots• 3 sizes available
• Available in white, tan and gray
• Split design to fit pipe penetrations with limited or no access from above
ultraPly tPo Pipe Boots• Available in white, tan and gray
• Universal Boots fit pipes from 1" to 6"
• Large Boot fits 6" to 8"
ultraPly tPo reinforced Curb Corners• Fabricated from 45 mil thick UltraPly TPO
• Available in 6 sizes to accommodate various curb sizes
ultraPly tPo inside/outside Corners• Specifically designed for flashing either inside or outside corners
on curbs, parapets and scuppers
ultraPly tPo t-Joint Covers• Designed to cover and seal T-Joints formed at seam intersections
memBrAne
ultraPly tPo unsupported Flashing
• Non-reinforced TPO for field fabrication of special details
• Available in white, tan and gray
ultraPly tPo 18" supported Flashing
• Specifically designed for curbs and parapet walls
• One edge is encapsulated, eliminating the need for cut-edge sealant
• Available in 50¹ rolls
ultraPly tPo 8" Cover strips
• Constructed of 60 mil thick UltraPly TPO
• 50’ length, pre-cut & ready to roll
• Available in white, tan and gray
Greater energy efficiency and a great value make thermoplastic polyolefin (TPO)
the fastest growing sustainable commercial roofing product available. Firestone
ultraPly™ tPo provides a heritage of excellence combined with the exclusive
Red Shield® warranty for a roof that delivers on quality and long-term perfor-
mance. And now, our complete line of UltraPly TPO accessories provides faster
installation, lower system costs and watertight seals around any roof protrusion.
A t o t A l t P o s o l u t i o n F r o m t h e B r A n d y o u t r u s t
Adhesives
ultraPly Bonding Adhesive• Specifically designed to bond
UltraPly TPO membrane to wood, metal, masonry and other substrates
ultraPly tPo Xr Bonding Adhesive• Specifically designed for use with
UltraPly TPO XR (fleece-backed) membrane
• Labor-saving, one-side-only application
• Applies with most standard application methods
ultraPly tPo Cut-edge sealant• Used to seal cut edges of membrane
where polyester reinforcement is exposed
• Available in white, tan and gray
ultraPly tPo general Purpose sealant• High-quality sealant with excellent
adhesion to a variety of surfaces
• Can be used as a fastener sealer, termination bar caulk and/or TPO cut-edge treatment
seAlAnts
Water Based Bonding Adhesive s• Water-based alternative to traditional
solvent-based adhesives
single-Ply lvoC Bonding Adhesive 1168• Formulated for special
low-VOC applications
• Complies with SCAQMD and LEED® requirements
single-Ply lvoC Bonding Adhesive• Faster dry time than competitive
solvent-based products
• Can be applied in cold weather, unlike water-based adhesives
lvoC Adhesives
The InvisiWeld Fastening System uses advanced technology to mechanically install
UltraPly™ TPO roofs without fasteners penetrating the roofing membrane. This
results in labor and materials savings, increased wind uplift resistance and a more
balanced load distribution across the roof.
• Plates are bonded to the underside of the membrane via induction heating
• Welds UltraPly TPO membrane to TPO coated InvisiWeld plate in seconds
• Required 25–50% fewer fasteners compared to conventional mechanically fastened TPO systems
Custom ACCessoriesNo two roofs are the same. If your roof has unique designs or elements, customized UltraPly TPO accessories from Firestone offer the same money-saving
benefits of our standard UltraPly TPO accessories and give you the confidence of knowing you’re getting quality accessories from a company you trust.
Pipe boots:
• Round, square or conical shaped
• Available with closed or split design
Custom Curb flashing:
• Allows for square or rectangular configurations Pipe Boot Conical Boot Square Tube Boot Curb Flashing
All Firestone custom accessories come with factory-formed welds and are fabricated from proven UltraPly TPO reinforced membrane.
the invisiWeld™ FAstening system
A C C e s s o r y l i n e
©2010 Firestone Building Products Printed in U.S.A. Item #1179 9/10 (replaces 8/09)-01
www.firestonebpco.comNote: This brochure is meant only to highlight Firestone’s products and specifications. Information is subject to change without notice. All products and specifications are
listed in approximate weights and measurements. For complete product and detail information, please refer to the appropriate Technical Manual. Firestone takes responsibility for furnishing quality materials which meet Firestone’s published product specifications. As neither Firestone itself nor its representatives practice architecture, Firestone offers no opinion on, and expressly disclaims any responsibility for, the soundness of any structure on which its products may be applied. If questions arise as to the soundness of a structure
or its ability to support a planned installation properly, the Owner should obtain opinions of competent structural engineers before proceeding. Firestone accepts no liability for any structural failure or for resultant damages, and no Firestone Representative is authorized to vary this disclaimer.
Firestone Building Products
250 West 96th St., Indianapolis, IN 46260
Corporate Office: 1-800-428-4442 • 317-575-7000 • Fax: 317-575-7100
international offices:
Firestone Building Products Canada
2835 Argentia Rd., Unit #2
Mississauga, ON L5N 8G6
1-888-292-6265 • 905-363-3150
Fax: 877-666-3022
Firestone Building Products Europe
Ikaroslaan 75 — 1930 Zaventem, Brussels, Belgium
+32 2 7114450 • Fax: +32 2 7212718
Firestone Building Products Latin America
8200 NW 52nd Terrace, Suite #107
Miami, FL 33166
305-471-0117 • Fax: 305-471-0377
MANUFACTURED WITH 100% WIND ENERGY
www.hardingpoorman.comHPG Uses 100% Green Power.
This green document printed on recycled paper using Soy Inks and manufactured using 100% Wind Power.
The InvisiWeld Fastening System uses advanced technology to mechanically install
UltraPly™ TPO roofs without fasteners penetrating the roofing membrane. This
results in labor and materials savings, increased wind uplift resistance and a more
balanced load distribution across the roof.
• Plates are bonded to the underside of the membrane via induction heating
• Welds UltraPly TPO membrane to TPO coated InvisiWeld plate in seconds
• Required 25–50% fewer fasteners compared to conventional mechanically fastened TPO systems
Custom ACCessoriesNo two roofs are the same. If your roof has unique designs or elements, customized UltraPly TPO accessories from Firestone offer the same money-saving
benefits of our standard UltraPly TPO accessories and give you the confidence of knowing you’re getting quality accessories from a company you trust.
Pipe boots:
• Round, square or conical shaped
• Available with closed or split design
Custom Curb flashing:
• Allows for square or rectangular configurations Pipe Boot Conical Boot Square Tube Boot Curb Flashing
All Firestone custom accessories come with factory-formed welds and are fabricated from proven UltraPly TPO reinforced membrane.
the invisiWeld™ FAstening system
A C C e s s o r y l i n e
©2010 Firestone Building Products Printed in U.S.A. Item #1179 9/10 (replaces 8/09)-01
www.firestonebpco.comNote: This brochure is meant only to highlight Firestone’s products and specifications. Information is subject to change without notice. All products and specifications are
listed in approximate weights and measurements. For complete product and detail information, please refer to the appropriate Technical Manual. Firestone takes responsibility for furnishing quality materials which meet Firestone’s published product specifications. As neither Firestone itself nor its representatives practice architecture, Firestone offers no opinion on, and expressly disclaims any responsibility for, the soundness of any structure on which its products may be applied. If questions arise as to the soundness of a structure
or its ability to support a planned installation properly, the Owner should obtain opinions of competent structural engineers before proceeding. Firestone accepts no liability for any structural failure or for resultant damages, and no Firestone Representative is authorized to vary this disclaimer.
Firestone Building Products
250 West 96th St., Indianapolis, IN 46260
Corporate Office: 1-800-428-4442 • 317-575-7000 • Fax: 317-575-7100
international offices:
Firestone Building Products Canada
2835 Argentia Rd., Unit #2
Mississauga, ON L5N 8G6
1-888-292-6265 • 905-363-3150
Fax: 877-666-3022
Firestone Building Products Europe
Ikaroslaan 75 — 1930 Zaventem, Brussels, Belgium
+32 2 7114450 • Fax: +32 2 7212718
Firestone Building Products Latin America
8200 NW 52nd Terrace, Suite #107
Miami, FL 33166
305-471-0117 • Fax: 305-471-0377
MANUFACTURED WITH 100% WIND ENERGY
www.hardingpoorman.comHPG Uses 100% Green Power.
This green document printed on recycled paper using Soy Inks and manufactured using 100% Wind Power.