Embed Size (px)
DESCRIPTION
manual
Citation preview
3rd ANGLE PROJECTION
7
14
3
5 108
118
15
2
1
A
B
CD
(2) 3410-0001153-01New O-Rings are Supplied with New
Ring Cylinder Assemblies.(See Notes)
SeeTable
F
SeeTable
ESee
TablePivot Bearing and DowelAre Supplied With Item "B"
But May Be Ordered Separately
9005-50-1019(Pivot Bearing Kit)
NOTES:If the Old Ring-Cylinder Will Be Re-installed, New O-Rings are Recommended.
See Sheet 2 for Boot Configurations
Rev. Description Initiator Date
05 Eco 11913; Added configuration for joystick style boot. Added sheet 2. LJH 5/13/14ITEM NO. QTY. PART NUMBER DESCRIPTION
1 1 3405-1210010-01-01 ADAPTER, 3/8x5/16[8mm], McM#51495K308
2 1 3405-2210001-01 1/8NPT Swivel Elbow, 5/32 (4mm) PL Tubing
3 1 3410-0001151-01 O-RING, 1/16 x 1/164 7 3500-1158008-21 M3 X 8 BHCS, SS5 1 3540-0102008-11 Dia 2mm x 8mm Dowel Pin6 1 3610-0340001-21 GARTER SPRING, RC 3407 1 3690-1200001-11 RET.INT. 2.76", UR-2688 5 3690-7500003-11 RET.,INT. 1" 5005-1009 1 3700-50-3019 HOUSING, FRONT, FLEXDEBURR
340, BLACK10 4 3700-50-3005 DISK, FILTER, FLEXDEBURR11 1 3700-50-3006 SUPPLY BOOT, FLEXDEBURR 34012 1 3700-50-3007 BOOT, FLEXDEBURR 34013 1 3700-50-3008 RING, BOOT, FLEXDEBURR 34014 1 9005-50-1000 RING CYLINDER, FLEXDEBURR
34015 1 9005-50-1002 ELBOW FITTING ASSY.,
FLEXDEBURR16 1 9005-50-1065 FDB-340 Motor Subassembly17 1 9005-50-1018 Rear Housing Assembly, RC-
300/340, Black18 1 9150-RC-C-12445 COLLET, 6mm, RC-300,-340 & -66019 1 3700-50-3079 Boot, RC-300/340, Viton20 2 3610-0235001-21 Garter Spring, RC 15021 1 3610-0494000-20 Garter Spring, SR-081 Boot
B1:51 2REVISION
NOTES: UNLESS OTHERWISE SPECIFIED.
DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS.
DRAWN BY:
CHECKED BY:
D.Lawson-7/31/06
L.Hines-8/10/06
TITLE
SCALE SIZE DRAWING NUMBER
PROJECT # SHEET OF 9630-50-RC-300 SERIES060725-1 05
PROPERTY OF ATI INDUSTRIAL AUTOMATION, INC. NOT TO BE REPRODUCED IN ANY MANNER EXCEPT ON ORDER OR WITH PRIOR WRITTEN AUTHORIZATION OF ATI.
1031 Goodworth Drive, Apex, NC 27539, USATel: +1.919.772.0115 Email: [email protected]: +1.919.772.8259 www.ati-ia.comISO 9001 Registered Company
RC-300 Series Service Parts
3rd ANGLE PROJECTION
20
20
21
19
Tapered Bellows Boot(Note 2)
1213
4
6
Flat Disk Boot(Note 1)
72.63
67.0713.70
212.66
52.09
52.6660.60166
83.13
140.48Center of SideMounting Pattern
Pivot Point(Center of Articulation)
Centering ForceApplication Point
Boot Notes:
Flat Disk Boots used until Summer 2014.1.Tapered Bellows Boot used after Summer 2014.2.
Rev. Description Initiator Date
- See Sheet1 - -
B1:52 2REVISION
NOTES: UNLESS OTHERWISE SPECIFIED.
DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS.
DRAWN BY:
CHECKED BY:
D.Lawson-7/31/06
L.Hines-8/10/06
TITLE
SCALE SIZE DRAWING NUMBER
PROJECT # SHEET OF 9630-50-RC-300 SERIES060725-1 05
PROPERTY OF ATI INDUSTRIAL AUTOMATION, INC. NOT TO BE REPRODUCED IN ANY MANNER EXCEPT ON ORDER OR WITH PRIOR WRITTEN AUTHORIZATION OF ATI.
1031 Goodworth Drive, Apex, NC 27539, USATel: +1.919.772.0115 Email: [email protected]: +1.919.772.8259 www.ati-ia.comISO 9001 Registered Company
RC-300 Series Service Parts
