Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
8mm SLIDING DOOR + SIDE PANEL
(CORNER FITTING ONLY)
DECIDE WHICH HAND IS REQUIRED. LEFT HAND OPENING ILLUSTRATED
V07/09/2014
ASSEMBLY INSTRUCTIONS
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Addition notes
Please inspect this product upon delivery. any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage of defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note--alumimium is a soft metal, and undergoes a series of extrusion.
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Hammer
Silicone Sealant
1
Assembly Drawing - Door + Side Panel
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(1) 1. x Inner Washer (8) 3. x Wall Plugs
(9) 3. x Screw Cover Caps
(10) 3. x Screws 4X30 (Pan Head)
(11) 3. x Screws 4X12 (Round Head)
(12) 3. x Screw Cap Washers
(13) 1 x Fixed panel.
(14) 1 x Door end closing seal.
(2) 1. x Outer Washer
(3) 2. x Screws 4X30 (Sink Head)
(4) 1. x Cover Cap ( Guide Rail)
(5) 1. x Cover Cap ( Vertical Profile)
(6) 1. x Cover Cap ( Wall Post)
(7) 1. x Wall Profile
FULL DETAILS SHOWN
IN RECESS FITTING GUIDE.
2
3
ASSEMBLY INSTRUCTIONS
If you require help, we advise you firstly contact a competent plumber
Installation Steps
Step 1THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
10
15
10
15
15
15
1200
800/900
524
593
MAKE SURE THE TRAY IS LEVEL, SING A SPIRIT LEVEL, BEFORE INSTALLING THISU
SHOWER PANEL / DOOR.
Step 2
Step 3
6mm
x4 x4
x4 x4
x4 x4
x4 x44x304x30
ENSURE THE SHOWER TRAY
IS FLAT AND LEVEL USING
A SPIRIT LEVEL
Φ6mm
Take care not to damage wall surface
4
15
Step 4
Step 5
5
Ø3mm
Step 6
Step 7
Ø6mm
6
Step 8
Step 9
72
60
2025
57
46
25
A B
A B
7
Sil icone
3.0mm
4x12
x6
x6
x6
Take care not to drill to the glass
Step 10
Step 11
AA How to adjust the width of the
sliding door + side panel
Minimum 10mm internal overlap required
Glass panel
Glass panel
Vertical profile
Vertical profile
Wall profile
Wall profile
Wall
Wall
Maximum adjustment
Minimum adjustment
8
Silicone (outside edge only) where the vertical profiles
meet the wall, and the fixed glass meets the tray
Step 12
9
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact out customer services quoting
the following:
Product name: 8mm Side Panel
Product code: SDP8008 SDP9008
Customer help line number:0344 804 48 48
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
10
/2014612
/14
Shower enclosures with aluminium profiles and safety glass
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.