8-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by

80010966-2018-R1.0 Page 1 of 10

936.

5298

/d

ngm

n 04

.25.

02.0

1 S

ubje

ct t

o al

tera

tion.

iBd81/81/5.61/5.61 °56/°56/°56/°56 0962–5961/0962–5961/069–896/069–896 annetnA troP-81°–10°/1°–10°/2.5°–12°/2.5°–12°T

Type No. 80010966Left side, lowband R1, connector 1–2

698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 15.7 16.1 16.4 16.5Gain over all Tilts dBi 15.6 ± 0.4 16.1 ± 0.3 16.3 ± 0.3 16.4 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 66 ± 2.9 65 ± 2.3 65 ± 2.6 64 ± 2.9Front-to-Back Ratio,Total Power, ± 30° dB > 23 > 23 > 24 > 25

Cross Polar Discriminationover Sector dB > 10.0 > 9.5 > 10.0 > 11.5

Vertical Pattern:Elevation Beamwidth ° 9.7 ± 0.7 9.0 ± 0.5 8.7 ± 0.5 8.3 ± 0.4Electrical Downtiltcontinuously adjustable ° 1.0 – 10.0

Tilt Accuracy ° < 0.4 < 0.4 < 0.4 < 0.4First Upper Side Lobe

noisserppuS dB > 16 > 18 > 18 > 20

Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R1 // R2)

> 30 (R1 // Y1, Y2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)

Max. Effective PowerPort 1–2 W 800 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.

698–960698–960 1695–2690 1695–2690

XX X X

65°65° 65° 65°

1°–10°1°–10° 2.5°–12° 2.5°–12°

R2R1 Y1 Y2

Page 2 of 10 80010966-2018-R1.0

8-Port Antenna

936.

5298

/d

ngm

n 04

.25.

02.0

1 S

ubje

ct t

o al

tera

tion.

Right side, lowband R2, connector 3–4

698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 15.5 16.0 16.3 16.6Gain over all Tilts dBi 15.5 ± 0.6 16.0 ± 0.5 16.3 ± 0.4 16.5 ± 0.4Horizontal Pattern:Azimuth Beamwidth ° 67 ± 3.5 65 ± 2.6 64 ± 3.0 63 ± 4.3Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 23 > 24 > 26

Cross Polar Discriminationover Sector dB > 9.5 > 10.5 > 10.0 > 11.5

Vertical Pattern:Elevation Beamwidth ° 9.8 ± 0.6 9.0 ± 0.7 8.6 ± 0.4 8.1 ± 0.5Electrical Downtiltcontinuously adjustable ° 1.0 – 10.0

Tilt Accuracy ° < 0.4 < 0.4 < 0.4 < 0.3First Upper Side Lobe

noisserppuS dB > 18 > 21 > 20 > 20

Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R2 // R1)

> 30 (R2 // Y1, Y2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)

Max. Effective PowerPort 3–4 W 800 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.

Left side, highband Y1, connector 5–6

1695–2690Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.6 18.0 18.3 18.1 17.9Gain over all Tilts dBi 17.5 ± 0.4 17.9 ± 0.4 18.1 ± 0.5 18.0 ± 0.6 17.8 ± 0.6Horizontal Pattern:Azimuth Beamwidth ° 64 ± 4.9 64 ± 5.0 62 ± 5.4 57 ± 5.7 61 ± 7.1Front-to-Back Ratio,Total Power, ± 30° dB > 24 > 26 > 26 > 25 > 24

Cross Polar Discriminationover Sector dB > 8.5 > 11.5 > 10.0 > 7.5 > 9.0

Vertical Pattern:Elevation Beamwidth ° 6.4 ± 0.5 5.9 ± 0.3 5.5 ± 0.4 4.8 ± 0.3 4.4 ± 0.2Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2 < 0.2First Upper Side Lobe

noisserppuS dB > 19 > 19 > 17 > 19 > 17

Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y1 // R1, R2, Y2)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)

Max. Effective PowerPort 5–6 W 400 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.

80010966-2018-R1.0 Page 3 of 10

8-Port Antenna93

6.52

98/d

ng

mn

04.2

5.02

.01

Sub

ject

to

alte

ratio

n.

Right side, highband Y2, connector 7–8

1695–2690Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.5 17.9 18.2 18.3 18.1Gain over all Tilts dBi 17.4 ± 0.5 17.8 ± 0.4 18.0 ± 0.6 18.2 ± 0.6 17.9 ± 0.6Horizontal Pattern:Azimuth Beamwidth ° 66 ± 3.0 66 ± 5.5 63 ± 6.9 56 ± 7.1 57 ± 7.7Front-to-Back Ratio,Total Power, ± 30° dB > 25 > 24 > 25 > 27 > 25

Cross Polar Discriminationover Sector dB > 9.5 > 11.0 > 10.0 > 9.5 > 10.5

Vertical Pattern:Elevation Beamwidth ° 6.4 ± 0.5 5.9 ± 0.3 5.6 ± 0.4 4.9 ± 0.4 4.4 ± 0.2Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2 < 0.1First Upper Side Lobe

noisserppuS dB > 19 > 18 > 18 > 19 > 18

Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y2 // R1, R2, Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)

Max. Effective PowerPort 7–8 W 400 (at 50 °C ambient temperature)

Values based on NGMN-P-BASTA (version 9.6) requirements.

8-Port Antenna

Electrical specifi cations, all systems

Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 27Passive Intermodulation dBc < –153 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 1200 (at 50 °C ambient

)erutarepmet Values based on NGMN-P-BASTA (version 9.6) requirements.

Mechanical specifi cations

Input 8 x 4.3-10 femaleConnector Position bottomAdjustment Mechanism FlexRET,

continuously adjustableN | lbf Frontal: 1400 | 315

Maximal: 1405 | 316Lateral: 250 | 57

Max. Wind Velocity km/hmph

241150

Height / Width / Depth mminches

2438 / 508 / 17596.0 / 20.0 / 6.9

Category of erawdraH gnitnuoM XH (X-Heavy)

Weight kglb

52.0 / 57.0 (clamps incl.)114.6 / 125.7 (clamps incl.)

Packing Size mminches

2635 / 542 / 268103.7 / 21.3 / 10.6

Scope of Supply Panel, FlexRET and clamps for 55–115 mm |2.2–4.5 inches diameter

Page 4 of 10 80010966-2018-R1.0

936.

5298

/d

ngm

n 04

.25.

02.0

1 S

ubje

ct t

o al

tera

tion.

3)

1)

1) 22 | 0.92) 150 | 5.93) 11 | 0.4

All dimensionsin mm | inches

2223

| 87

.5

2485

| 97

.8

2438

| 96

.0

2)

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.

Material: Refl ector screen: Aluminum.Fiberglass housing: laiceps ehT .stnenopmoc annetna lanretni eht yllatot srevoc tI

rehtaew tseb eht seetnaraug dna muminim a ot saera gnilaes eht secuder ngised ,ytilibats ot sdrager htiw ecnamrofrep mumitpo seetnaraug lairetam ssalgrebiF .noitcetorpstiffness, UV resistance and painting. The color of the radome is light grey.All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.

Site Sharing Adapter3-way

FlexRET

BTS1 BTS2 BTS3

FlexRET FlexRET

AISG

Site Sharing Adapter6-way

FlexRET

BTS3 BTS4

FlexRET FlexRET

BTS2BTS1 BTS5 BTS6

AISG

Configuration example with Site Sharing Adapter 86010154

Configuration example with Site Sharing Adapter 86010155

For more information please refer to the respective data sheets.

Accessories (order separately if required)

Type No. Description Remarksmm | inches

Weightapprox. kg | lb

Units per antenna

85010097 2 clamps Mast diameter: 110 – 220 | 4.3 – 8.7 9.4 | 20.7 185010099 1 downtilt kit Downtilt angle: 0° – 10° 10.6 | 23.4 1

0.7 | 1.51.4 | 3.1

86010162 Gender Adapter Solely to be used in combination with the FlexRET module 86010153V01

0.045 | 0.099 186010163 Port Extender 0.16 | 0.35 1

Accessories (included in the scope of supply)85010096 2 clamps Mast diameter: 55 – 115 | 2.2 – 4.5 5.0 | 11.0 186010153V01 FlexRET 1

Wind load (at Rated WindSpeed: 150 km/h) (93 mph)

EPA (m2 | ft2 ) Front: 1.286 | 13.84Lateral: .230 | 2.48

8-Port Antenna

Bottom view* Dimensions refer to radomeAll dimensions in mm | inches

126 | 5.0

508 | 20.0 *

226 | 8.9

326 | 12.8

426 | 16.8

93 |

3.7

*

240

| 9.4

* 175

| 6.9

*

R 4

698 - 960

R2L 2

698 - 960

R1R 3

698 - 960

R2L 1

698 - 960

R1R 8

1695-2690

Y2L 6

1695-2690

Y1R 7

1695-2690

Y2Y1L 5

1695-2690

Layout of interface:

Correlation Table

Frequency range Array Connector

698–960 MHz R1 1–2698–960 MHz R2 3–4

1695–2690 MHz Y1 5–61695–2690 MHz Y2 7–8

R1Y1

R2Y2

Left Right

80010966-2018-R1.0 Page 5 of 10

936.

5298

/d

ngm

n 04

.25.

02.0

1 S

ubje

ct t

o al

tera

tion.

936.

5063

S

ubje

ct t

o al

tera

tion.

Mounting HardwareClamp(Wind Load Category “XH”)

Clamp

Type No. 85010096Suitable for mast diameter

mminches

55 – 1152.2 – 4.5

pmalc rewol x 1ylppus fo epocS1 x upper clamp

pmalC – lairetaM– Screws– Nuts

Hot-dip galvanized steelHot-dip galvanized steel

Stainless steelWeight kg

lb5.011.0

A B C D E F G H

mminches

2007.9

692.7

893.5

55 – 1152.2 – 4.5

1505.9

1305.1

(19)(0.7)

(39)(1.5)

.stun retnuoc esu ot dnemmocer ton seod nierhtaK :eton esaelP

G HE

CBA

F

lower clamp upper clamp

D

G

low

er c

lam

pH

upp

er c

lam

p

1)Attention!Square of the screw must be positioned in the square hole before tightening the nut.

2)All nuts have the same wrench size 17.

TorqueMA = 40 Nm

TorqueMA = 40 Nm

TorqueMA = 40 Nm

TorqueMA = 40 Nm

80010966-2018-R1.0 Page 6 of 10

Type No. 86010153V01Protocols compliant to 3GPP/AISG 2.0Logical interface ex factory 3GPP/AISG 2.0Operates as Single RETs or Multi RETEx factory Single RETsInput voltage range V 10 ... 30 (pin 6)Power consumption W Typically < 1; < 10 (motor activated)Connectors 2 x 8 pin connector according to IEC 60130-9; according to AISG-C 485

Daisy chain in: male; Daisy chain out: femaleHardware interfaces RS 485A/B (pin 5, pin 3);

power supply (pin 6); DC return (pin 7);according to AISG / 3GPP

Adjustment time (full range)

sec 40(typically, depending on antenna type)

Adjustment cycles > 50,000Temperature range °C –40 … +60Protection class IP 24 (installed)Lightning protection AISG interface (each pin)

2.5 kA (10/350 µs)8 kA (8/20 µs) according to IEC 61000-4-5

Housing materialWeight g

lb3500.77

Packing size(H x W x D)

mminches

245 x 93 x 1029.6 x 3.6 x 4

Dimensions (H x W x D)

mminches

142 x 71 x 515.6 x 2.8 x 2

Please note:If the Primary which controls the FlexRET system does not support the default ex-factory interface setting, then the FlexRET must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information.

If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna

Standards: EN 60950-1 (Safety)EN 60950-22 (Safety – Equipment installed outdoor)EN 55022 (Emission)EN 55024 (Immunity)ETS 300019-1-4 (Environmental)UL 60950-1; 1st edition

cation: CE, FCC

Scope of supply: FlexRET

Optional: Site Sharing Adapter (86010154 or 86010155) to create independent logical erom htiw etarepo ot elbissop ti sekaM .etis ro annetna eno ta secafretni

.B edoN tnednepedni eno naht

Gender Adapter (86010162) to convert the AISG out (female) to an AISG in (male) port in order to operate one FlexRet with exactly 2 BTS. Detailed information is given in the data sheet of the Gender Adapter.

Port Extender (86010163) to convert the existing AISG input and output in order to operate FlexRet with exactly 2 BTS while maintaining the daisy chain capability.Detailed information is given in the data sheet of the Port Extender.

Please note:In general, the addressing of the FlexRET is automatically performed. Only in case the FlexRET is manually addressed, the serial number has to be extended by the corresponding colour coding extension (e.g. CSG351234-R1). The respective information can be found on the site documentation which is included in the scope of supply.

936.

5204

S

ubje

ct t

o al

tera

tion.

FlexRET

• Compliant to 3GPP/AISG 2.0 • Daisy Chain feasibility• Single RETs or Multi RET displayed • gured• Two way antenna sharing feasibility

Page 8 of 10 80010966-2018-R1.0

936.

5204

S

ubje

ct t

o al

tera

tion.

FlexRET

Startup of FlexRET

cable and scanning the antenna line devices (ALD) the used primary (e.g. NodeB, ALC, etc.)

Connecting the control cables:

xing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’).The connector should be tightened by hand or by a special torque screw driver (order no. 85010080).See also data sheet for Kathrein AISG-cable (86010007, ...). Please note: To ensure the tightness of the RET System, Kathrein recommend the use of Kathrein components only.Please note: If the daisy chain output is not used, do not remove the protection cap.

For daisy chain operation, remove the protection cap and attach a control cable to interconnect with the daisy chain input of the subsequent FlexRET or external RCU.

TERxelF tsal eht fo tuptuo niahc ysiad eht no pac noitcetorp eht evomer ton oD :eton esaelPor RCU device.

936.

5204

S

ubje

ct t

o al

tera

tion.

FCC – Statements

936.

5204

S

ubje

ct t

o al

tera

tion.

FCC – Statements

Compliance Information Statement(Declaration of Conformity Procedure)

Model Name: FlexRET FCC ID SP3-86010153

Page 10 of 10 80010966-2018-R1.0