Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
25CZ215E/CZ315E
En
glish
8. INSTALLATION/WIRE CONNECT GUIDE
Before Starting1. This set is exclusively for use in cars
with a negative ground, 12 V power supply.
2. Read these instructions carefully.3. Be sure to disconnect the battery “-”
terminal before starting. This is to prevent short circuits during installation. (Figure 1)
Figure 1
Car battery
Figure 1
Package ContentsMain unit .................................................1Owner’s manual & Installation manual ....1Warranty card .........................................1Power extension lead .............................1Mounting bracket ....................................1Outer escutcheon............................1
Parts bag ................................................1• Special screw ..................................1• Rubber part .....................................1• Removal key ....................................2• Stopper.............................................1
General Cautions1. Do not open the case. There are no user serviceable parts inside. If you drop anything
into the unit during installation, consult your dealer or an authorized Clarion service center.
2. Use a soft, dry cloth to clean the case. Never use hard cloth, thinner, benzene, alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently.
Cautions on Installation1. Prepare all articles necessary for installing the main unit before starting.2. Install the unit within 30° of the horizontal plane. (Figure 2)3. If you have to do any work on the car body, such as drilling holes, consult your car
dealer beforehand.4. Use the enclosed screws for installation. Using other screws can cause damage.
(Figure 3)
Max. 30˚
Figure 2
Figure 3
Max. 8 mm
Chassis Chassis
Damage
Figure 2 Figure 3
CZ315E&CZ215E Owner's Guide A6 1112.indd 25 2015/01/09 9:25:41
26 CZ215E/CZ315E
En
glish
Installing the Main Unit1. Place the universal mounting bracket into the instrument panel, use a screwdriver to
bend each stopper of the mounting bracket inward, then secure the stopper. (Figure 4)2. Wire as shown on page 30.3. Insert the main unit into the universal mounting bracket.4. Mount the outer escutcheon so that all the hooks are locked. (Figure 7, 8 on page
28)Notes:• Somecarmodelsrequirespecialmountingkitsforproperinstallation.ConsultyourClarion
dealerfordetails.• Fastenthefrontstoppersecurelytopreventthemainunitfromcomingloose.
Rear Fastening Hole (of car)
Special Screw (included)
Stoppers
Instrument PanelStopper
Screwdriver
Outer Escutcheon
Main Unit
Universal Mounting Bracket (included)
Spring
Figure 4
Rubber Cap (included)
Figure 4• Console opening dimensions
182mm
53m
m
Hole
CAUTIONPRECAUTIONPush in the protruding part (STOPPER) as shown in the Figure 5. When this main unit is installed without the universal mounting bracket.
CZ315E&CZ215E Owner's Guide A6 1112.indd 26 2015/01/09 9:25:41
27CZ215E/CZ315E
En
glish
Stoper
Main Unit
Figure 5 Figure 5
Fixed Mount (Using the bracket originally equipped in vehicle)If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (★). (Figure 6)If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the main unit in the following procedure.1. Secure the mounting brackets to the chassis as shown in Figure 6. When the main unit
is installed without the universal mounting bracket, holes exist; modification, such as drilling new holes, of the mounting brackets may be required for other models.
2. Wire as shown in Installation (page 30).3. Secure the unit in the dashboard, and then reassemble the dashboard and the center
panel.
**
**
2
4
3
5
1
6
7
1 Center Panel (Note 1)2 Mounting bracket
(1 pair for the left and right sides)3 Source Unit4 Pocket5 Dashboard6 4-The screws are Included with
the unit*. (8 mm Max.)7 Note 2
Figure 6* : The screws with this mark are included with the unit. (Note 3).★: The screws with this mark are originally attached to the vehicle.
CZ315E&CZ215E Owner's Guide A6 1112.indd 27 2015/01/09 9:25:42
28 CZ215E/CZ315E
En
glish
Note 1:• Insomecases,thecenterpanelmayrequiresomemodification(trimming,filling,etc.).Note 2:• Ifahookontheinstallationbracketinterfereswiththeunit,bendandflattenitwithanipperor
asimilartool.Note 3:• Ifreattachingscrewswhichhavebeendetached,removeanyfilingsfromthescrewsand
screwmountingbracket.
Removal1. Remove the Detachable Control Panel (DCP). For instructions on removing the DCP,
refer to the owner’s guide.2. Press the outer escutcheon upward and remove it. (Figure 7)3. Insert and lock the hook plates. (Figure 8)4. Pull the hook plates to remove the main unit.
Outer EscutcheonRemoval key
Figure 7 Figure 8 Figure 7 Figure 8
CZ315E&CZ215E Owner's Guide A6 1112.indd 28 2015/01/09 9:25:42
29CZ215E/CZ315E
En
glish
Cautions on Wiring1. Be sure to turn the power off when wiring.2. Be particularly careful where you route the cables. Keep them well away from the
engine, exhaust pipe, etc. Heat may damage the wires.3. If the fuse should blow, check that the wiring is correct. If it is, replace the fuse with a
new one with the same amperage rating as the original one. (Figure 9)4. When the main power supply fuse in the car is 15 A or less, purchase an automotive
cable that can withstand 15 A and supply this unit with power directly from the battery to ensure that the unit will operate normally. Note that a fuse must be installed at a distance no longer than 30 cm from the cable battery terminal to prevent accidents.
Fuse
Fuse holder
Figure 9
For VW and Audi Vehicles1. For VW and Audi vehicles, change the position of fuse installation as shown on the
diagram. (Figure 10)2. When the car stereo is installed in 1998 and later Volkswagen models, remove the
auto antenna leads (A-5), g and f. Be sure to insulate both the ISO connector side terminal f and the main unit side terminal g with insulation tape, respectively. (Figure 11)
3. When the main unit is also connected to an external amplifier, connect REMOTE on the external amplifier to AMP Remote lead.
Figure 10
a
eb
c
d
b
e
c
d
For models 1992 and later For models up to 1991
a Yellowb Redc Yellowd Rede Yellowf Blue/whiteg Blue/white
g f
Insulation tape
Insulate the terminal
∗ Never let the terminals make contact with the metal plate parts of the car.
AMP Remote
Figure 11
Figure 10Figure 10
a
eb
c
d
b
e
c
d
For models 1992 and later For models up to 1991
a Yellowb Redc Yellowd Rede Yellowf Blue/whiteg Blue/white
g f
Insulation tape
Insulate the terminal
∗ Never let the terminals make contact with the metal plate parts of the car.
AMP Remote
Figure 11 Figure 11
CZ315E&CZ215E Owner's Guide A6 1112.indd 29 2015/01/09 9:25:43
30 CZ215E/CZ315E
En
glish
Wire ConnectionsCAUTION:• Pleasemakesurewhenconnectingexternalpoweramplifier,thatyouproperly,tothe
carchassis,groundtheamplifier.Ifthisisnotdone,severedamagetothemainunitmayhappen.
Steering wheel remote control(sold separately)
* RCA
Main Unit Rear
Antenna
Microphone (CZ315E only) (RCB204: sold separately)
Fuse ca
5
e
fg
15A
bd
B-2 B-1 B-3B-4
A-4A-5 A-5
B-5 B-6
A-8 A-7
B-8B-7
A-6
ISO connector
No. DescriptionB-1 REAR RIGHT +B-2 REAR RIGHT -B-3 FRONT RIGHT +B-4 FRONT RIGHT -B-5 FRONT LEFT +B-6 FRONT LEFT -B-7 REAR LEFT +B-8 REAR LEFT -
A-4 BACK UPA-5 REMOTE/POWER ANTANNAA-6 ILLUMINATIONA-7 +12 V ACCESSORYA-8 GROUND
REAR/SUBWOOFERRIGHT purple (Red)
REAR/SUBWOOFERLEFT purple (White)
FRONT RIGHT Grey (Red)FRONT LEFT Grey (White)
1
2
3
4
5 AMP REMOTE
Notes:• Externalmicrophonehastobeconnectedatthebackofthemainunitduringinstallationif
necessary.• Byconnectingoptionalexternalmicrophone,internalmicrophoneiscanceledautomatically.
CZ315E&CZ215E Owner's Guide A6 1112.indd 30 2015/01/09 9:25:44