Upload
hugo-mendes
View
222
Download
1
Embed Size (px)
Citation preview
8/6/2019 7 - Trim and Upholstery
1/112
Renault s.a.s 2008
"The repair methods given by the manufacturer in this document are based on the technical
specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the manufacturer in theproduction of the various component units and accessories from which his vehicles areconstructed."
All copyrights reserved by Renault.
The reproduction or translation in part of whole of the present document, as well as the useof the spare parts reference numbering system, are prohibited without the prior writtenconsent of Renault.
JULY2008 Edition Anglaise
X95
7 Trim and upholstery
71A BODY INTERNAL TRIM
72A SIDE OPENING ELEMENT TRIM
73A NON-SIDE OPENING ELEMENTS TRIM
75A FRONT SEAT FRAMES AND MECHANISMS
76A REAR SEAT FRAMES AND MECHANISMS
77A FRONT SEAT TRIM
78A REAR SEAT TRIM
79A SEAT COMPONENTS
8/6/2019 7 - Trim and Upholstery
2/112
MEGANE III - Section 7
Contents
Page
MEGANE III- Section 7ContentsPage
71A BODY INTERNAL TRIM
Floor carpet: Removal -Refitting 71A-1
Headlining: Removal -Refitting 71A-4
Door sill lining: Removal -Refitting 71A-15
Front door sill lining:Removal - Refitting 71A-17
B-pillar lower trim: Removal -Refitting 71A-19
Rear door sill lining: Removal- Refitting 71A-20
Rear wheel arch lining:
Removal - Refitting 71A-22
A-pillar trim: Removal -Refitting 71A-24
Rear roof drip mouldinglining: Removal - Refitting 71A-26
B-pillar upper trim: Removal -Refitting 71A-27
Rear door sill upper lining:Removal - Refitting 71A-32
C-pillar upper trim: Removal- Refitting 71A-33
Rear quarter panel trim:Removal - Refitting 71A-34
Rear panel trim: Removal -Refitting 71A-36
Rear parcel shelf side trim:Removal - Refitting 71A-38
Rear end panel lining:Removal - Refitting 71A-40
72A SIDE OPENING ELEMENT TRIM
Front side door trim:Removal - Refitting 72A-1
Rear side door trim: Removal- Refitting 72A-4
73A NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal -Refitting 73A-1
75AFRONT SEAT FRAMES ANDMECHANISMS
Front seat base frame:Removal - Refitting 75A-1
Front seatback frame:Removal - Refitting 75A-4
Front seat runner: Removal -Refitting 75A-7
Front seat remoteadjustment: Removal -Refitting 75A-10
Front seat lumbaradjustment: Removal -Refitting 75A-11
Front seat sliding motor:Removal - Refitting 75A-14
Front seat height adjustmentmotor: Removal - Refitting 75A-17
Front seat backrest tilt motor:Removal - Refitting 75A-19
Complete front seat:
Removal - Refitting 75A-22
8/6/2019 7 - Trim and Upholstery
3/112
Contents
76A REAR SEAT FRAMES AND MECHANISMS
Single unit rear benchseatback: Removal - Refitting 76A-1
1/3 and 2/3 rear benchseatback: Removal - Refitting 76A-3
Single unit rear bench seat:Removal - Refitting 76A-5
Rear bench seatback frame1/3 and 2/3: Removal -Refitting 76A-6
Rear bench seatmechanism: Removal -
Refitting 76A-7Rear bench seat single-unitseatback frame: Removal -Refitting 76A-9
77A FRONT SEAT TRIM
Front seat base trim:Removal - Refitting 77A-1
Front seatback trim: Removal- Refitting 77A-4
Front seat lower cover:Removal - Refitting 77A-9
78A REAR SEAT TRIM
1/3 and 2/3 rear bench seattrim: Removal - Refitting 78A-1
1/3 and 2/3 rear bench seatseatback trim: Removal -Refitting 78A-3
Rear bench seat single unitseatback trim: Removal -Refitting 78A-6
Rear bench seat single unitseat base trim: Removal -Refitting 78A-9
79A SEAT COMPONENTS
Front headrest: Removal -Refitting 79A-1
Heated seat cover: Removal- Refitting 79A-2
Front seat headrest guide:Removal - Refitting 79A-4
Rear centre arm rest:Removal - Refitting 79A-5
Rear seat headrest guide:Removal - Refitting 79A-6
8/6/2019 7 - Trim and Upholstery
4/11271A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
B95 or D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
a Remove:
- the front seats completely (see 75A, Front seatframes and mechanisms, Complete front seat:Removal - Refitting, page 75A-22) ,
- the central console (see Centre console: Remo-val - Refitting) (57A, Interior equipment),
- the single unit rear bench seat base (see 76A,
Rear seat frames and mechanisms, Single unitrear bench seat: Removal - Refitting, page 76A-5) ,
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) ,
- the floor storage compartment and flap (see Floorflap and storage: Removal - Refitting) (57A, Inte-rior equipment).
a Remove:
- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-17) ,
- the rear door sill lining (see 71A , Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
- the C-pillar upper trim (see 71A, Body internal
trim, C-pillar upper trim: Removal - Refitting,
page 71A-33) ,
- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) .
a Remove:
- the door sill lining (see 71A, Body internal trim,Door sill lining: Removal - Refitting, page 71A-15) ,
- the rear panel trim (see 71A, Body internal trim,
Rear panel trim: Removal - Refitting, page 71A-36) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a Remove:
- the clips (1) ,
- the mounting supports of the rear bench seat base
(2) .
a Remove the clips (3) .
B95
D95
136664
135098
8/6/2019 7 - Trim and Upholstery
5/11271A-2
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
B95 or D95
71A
a Unfasten clip (4) .
a Remove:
- the accelerator pedal stop (5) ,
- the floor carpet.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
- the floor carpet,
- the accelerator pedal stop (5),
- the clips (4), (3)and (1),
- the mounting supports of the rear bench seat base(2).
II - FINAL OPERATION
a Refit:
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) ,
- the door sill lining (see 71A, Body internal trim,
Door sill lining: Removal - Refitting, page 71A-15) .
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,page 71A-19) ,
- the C-pillar upper trim (see 71A, Body internaltrim, C-pillar upper trim: Removal - Refitting,page 71A-33) ,
- the rear door sill lining (see 71A, Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,
page 71A-17) .
136661
135097
D95
B95
8/6/2019 7 - Trim and Upholstery
6/11271A-3
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
B95 or D95
71A
a Refit:
- the floor storage compartment and flap (see Floorflap and storage: Removal - Refitting) (57A, Inte-rior equipment),
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) ,
- the single unit rear bench seat base (see 76A,Rear seat frames and mechanisms, Single unitrear bench seat: Removal - Refitting, page 76A-5) ,
- the central console (see Centre console: Remo-val - Refitting) (57A, Interior equipment),
- the front seats completely (see 75A , Front seatframes and mechanisms, Complete front seat:
Removal - Refitting, page 75A-22) .a Connect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
8/6/2019 7 - Trim and Upholstery
7/11271A-4
BODY INTERNAL TRIM
Headlining: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
a Remove:
- the upper cover of the interior rear view mirrorusing the tool (Car. 1363),
- the lower cover of the interior rear view mirror.
a Unclip the lower cover from the interior rear viewmirror.
a Disconnect the interior rear view mirror connectors.
a Remove:
- the side door seals partially,
- the sun visors (see Sun visor: Removal - Refit-ting) (57A, Interior equipment),
- the interior lights (see Courtesy light: Removal -Refitting) (81B, Interior lighting),
- the grab handles (see Grab handle: Removal -Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-nal trim, A-pillar trim: Removal - Refitting, page71A-24) .
a Disconnect the headlining wiring connectors.
a Remove the single unit rear bench seat base (see76A, Rear seat frames and mechanisms, Singleunit rear bench seat: Removal - Refitting , page76A-5) .
Essential special tooling
Car. 1363 Set of trim removal levers.
IMPORTANT
To avoid any risk of damaging the systems, applythe safety and cleanliness instructions and opera-tion recommendations before carrying out therepair (see Airbag and Pretensioners: Precau-tions for repair) (88C, Airbags and pretensioners).
137004
137499
137500
REAR BENCH FUNCTION
8/6/2019 7 - Trim and Upholstery
8/11271A-5
BODY INTERNAL TRIM
Headlining: Removal - Refitting
D95
71A
a Remove the 1/3 and 2/3 rear bench seat base (see1/3 and 2/3 rear bench seat:Removal - Refitting) .
a Remove:
- the luggage compartment seal partially,
- the side roof rail rear trims (see 71A, Body inter-nal trim, Rear roof drip moulding lining: Remo-val - Refitting, page 71A-26) ,
- the C-pillar upper trims (see 71A, Body internaltrim, C-pillar upper trim: Removal - Refitting,page 71A-33) ,
- the B-pillar upper trims (see 71A , Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-27) ,
- the rear parcel shelf side trims (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) ,
- the rear quarter panel trims (see 71A, Body inter-nal trim, Rear quarter panel trim: Removal - Re-
fitting, page 71A-34) .
a Mark the positioning of the finishing seal (1) .
a Remove the finishing seal.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Unclip the rear mountings.
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
FIXED WINDOW SUNROOF
137503
137511
137510
8/6/2019 7 - Trim and Upholstery
9/11271A-6
BODY INTERNAL TRIM
Headlining: Removal - Refitting
D95
71A
a Unclip the trims.
a Unclip the side mountings at (2) using a flat-bladescrewdriver.
a Unclip the headlining front section (3) .
a Unclip the headlining central section (4) .
137508
137509
137174
137498
137486
8/6/2019 7 - Trim and Upholstery
10/11271A-7
BODY INTERNAL TRIM
Headlining: Removal - Refitting
D95
71A
a Remove the headlining (this operation requires twopeople).
REFITTING
I - REFITTING PREPARATION OPERATION
a Check the presence and the condition of the velcrostrips (5) .
II - REFITTING OPERATION FOR PARTCONCERNED
a
a Fit the headlining (this operation requires two peo-
ple).a Clip:
- the headlining central section (4),
- the headlining front section (3),
- the side mountings,
- the trims,
- the rear mountings.
III - FINAL OPERATION
a Refit the finishing seal.
a Refit:
- the rear quarter panel trims (see 71A, Body inter-nal trim, Rear quarter panel trim: Removal - Re-
fitting, page 71A-34) ,- the rear parcel shelf side trims (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) ,
- the B-pillar upper trims (see 71A , Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-27) ,
- the C-pillar upper trims (see 71A, Body internaltrim, C-pillar upper trim: Removal - Refitting,page 71A-33) ,
- the side roof rail rear trims (see 71A, Body inter-nal trim, Rear roof drip moulding lining: Remo-val - Refitting, page 71A-26) ,
- the luggage compartment seal.
137393
137486
FIXED WINDOW SUNROOF
Note:
For vehicles equipped with a sunroof, the headli-ning must be handled with care. The side edgesare weakened by the design of the sunroof.
FIXED WINDOW SUNROOF
8/6/2019 7 - Trim and Upholstery
11/11271A-8
BODY INTERNAL TRIM
Headlining: Removal - Refitting
D95
71A
aRefit the 1/3 and 2/3 rear bench seat base (see 1/3and 2/3 rear bench seat:Removal - Refitting) .
a Refit the single unit rear bench seat base (see 76A,Rear seat frames and mechanisms, Single unit
rear bench seat: Removal - Refitting, page 76A-5).
a Connect the headlining wiring connectors.
a Refit:
- the windscreen pillar trims (see 71A, Body inter-nal trim, A-pillar trim: Removal - Refitting, page71A-24) ,
- the grab handles (see Grab handle: Removal -Refitting) (57B, Interior equipment),
- the interior lights (see Courtesy light: Removal -
Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-ting) (57A, Interior equipment),
- the side door seals partially.
a Connect the interior rear view mirror connectors.
a Refit:
- the lower cover of the interior rear view mirror,
- the upper cover of the interior rear view mirror.
a Connect the battery (see Battery : Removal - Refit-
ting) (80A, Battery).
a Carry out a function test.
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
REAR BENCH FUNCTION
8/6/2019 7 - Trim and Upholstery
12/11271A-9
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
a Remove the sunroof switch (see Sunroof switch:Removal - Refitting) (87D, Electric windows - Sun-roof).
a Remove:
- the interior lights (see Courtesy light: Removal -Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-ting) (57A, Interior equipment),
- the grab handles (see Grab handle: Removal -Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-nal trim, A-pillar trim: Removal - Refitting, page71A-24) .
a Disconnect the headlining wiring connectors (1) .
Essential special tooling
Car. 1363 Set of trim removal levers.
IMPORTANT
To avoid any risk of damaging the systems, applythe safety and cleanliness instructions and opera-tion recommendations before carrying out therepair (see Airbag and Pretensioners: Precau-tions for repair) (88C, Airbag and pretensioners).
PANORAMIC SUNROOF
137500
137499
8/6/2019 7 - Trim and Upholstery
13/11271A-10
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
a Remove:
- the upper cover of the interior rear view mirror (2)using the tool (Car. 1363),
- the lower cover of the interior rear view mirror.
a Disconnect the connectors (3) on the interior rearview mirror.
a Mark the positioning of the finishing seals.
a Remove the finishing seals (4) .
a Remove the single unit rear bench seat base (see76A, Rear seat frames and mechanisms, Singleunit rear bench seat: Removal - Refitting , page76A-5) .
a Remove the 1/3 and 2/3 rear bench seat base (see1/3 and 2/3 rear bench seat:Removal - Refitting) .
a Remove:
- the side door seals partially,
- the luggage compartment seal partially,- the rear door sill linings (see 71A, Body internal
trim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
137004
137003
PANORAMIC SUNROOF
137172
REAR BENCH FUNCTION
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
8/6/2019 7 - Trim and Upholstery
14/11271A-11
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
- the front door sill linings (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-17) ,
- the B-pillar upper trims (see 71A , Body internal
trim, B-pillar upper trim: Removal - Refitting,page 71A-27) ,
- the rear parcel shelf side trim panels (see 71A,Body internal trim, Rear parcel shelf side trim:Removal - Refitting, page 71A-38) ,
- the rear quarter panel trims (see 71A, Body inter-nal trim, Rear quarter panel trim: Removal - Re-fitting, page 71A-34) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Unclip the rear mountings.
a Unclip the trims.
a Unclip the side mountings.
137511
137508
137502
137501
8/6/2019 7 - Trim and Upholstery
15/11271A-12
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
a
Unclip the headlining front section (5) .
a Unclip the headlining central section (6) .
a
Remove the headlining (this operation requires twopeople).
137174
137482
137175
8/6/2019 7 - Trim and Upholstery
16/11271A-13
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
REFITTING
I - REFITTING PREPARATION OPERATION
a Check the presence and the condition of the velcrostrips (7) .
II - REFITTING OPERATION FOR PARTCONCERNED
a
aFit the headlining (this operation requires two peo-ple).
a Clip:
- the headlining central section,
- the headlining front section,
- the side mountings,
- the trims,
- the rear mountings.
III - FINAL OPERATION
a Refit:
- the rear quarter panel trims (see 71A, Body inter-nal trim, Rear quarter panel trim: Removal - Re-fitting, page 71A-34) ,
- the rear parcel shelf side trim panels (see 71A,Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-38) ,
- the B-pillar upper trims (see 71A , Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-27) ,
- the luggage compartment seal,
- the front door sill linings (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-17) ,
- the rear door sill linings (see 71A, Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
- the side door seals.
137482
137483
PANORAMIC SUNROOF
Note:
For vehicles equipped with a sunroof, the headli-ning must be handled with care. The side edgesare weakened by the design of the sunroof.
8/6/2019 7 - Trim and Upholstery
17/11271A-14
BODY INTERNAL TRIM
Headlining: Removal - Refitting
B95
71A
aRefit the 1/3 and 2/3 rear bench seat base (see 1/3and 2/3 rear bench seat:Removal - Refitting) .
a Refit the single unit rear bench seat base (see 76A,Rear seat frames and mechanisms, Single unitrear bench seat: Removal - Refitting, page 76A-5).
a Refit the finishing seal.
a Connect the connectors on the interior rear view mir-ror.
a Clip:
- the lower trim of the rear view mirror cover,
- the upper trim of the rear view mirror cover.
a Connect the headlining wiring connector.
a Refit:
- the windscreen pillar trims (see 71A, Body inter-nal trim, A-pillar trim: Removal - Refitting, page71A-24) ,
- the grab handles (see Grab handle: Removal -Refitting) (57A, Interior equipment),
- the sun visors (see Sun visor: Removal - Refit-ting) (57A, Interior equipment),
- the interior lights (see Courtesy light: Removal -Refitting) (81B, Interior lighting).
a Refit the sunroof switch (see Sunroof switch: Re-moval - Refitting) (87D, Electric windows - Sun-roof).
a Connect the battery (see Battery : Removal - Refit-ting) (80A, Battery).
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
REAR BENCH FUNCTION
PANORAMIC SUNROOF
PANORAMIC SUNROOF
8/6/2019 7 - Trim and Upholstery
18/11271A-15
BODY INTERNAL TRIM
Door sill lining: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the front side door seal partially,
- the bonnet release handle (1) ,- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the door sill lining (2) .
137119
137316
137121
8/6/2019 7 - Trim and Upholstery
19/11271A-16
BODY INTERNAL TRIM
Door sill lining: Removal - Refitting
D95
71A
a Remove the door sill lining (3) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the door sill lining (3),
- the door sill lining (2).
II - FINAL OPERATION
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,page 71A-19) ,
- the bonnet release handle,
- the front side door seal.
137115
137117
8/6/2019 7 - Trim and Upholstery
20/11271A-17
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the bonnet release handle (1) ,
- the front side door seal partially,- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the front door sill lining (2) .137119
137111
8/6/2019 7 - Trim and Upholstery
21/11271A-18
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting
B95
71A
a Remove the front door sill lining (3) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the front door sill lining (3),
- the front door sill lining (2).
II - FINAL OPERATION
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,page 71A-19) ,
- the front side door seal,
- the bonnet release handle.
137115
137117
8/6/2019 7 - Trim and Upholstery
22/11271A-19
BODY INTERNAL TRIM
B-pillar lower trim: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially remove the front and rear side door seals.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the B-pillar lower trim (1) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the B-pillar lower trim.
II - FINAL OPERATION
a Refit the front and rear side door seals.
137107
137109
8/6/2019 7 - Trim and Upholstery
23/11271A-20
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) ,
- the rear inner sill upper trim (see 71A, Body inter-nal trim, Rear door sill upper lining: Removal -Refitting, page 71A-32) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove:
- the clip (1) ,
- the rear door sill lining (2) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear door sill lining.
137099
137102
8/6/2019 7 - Trim and Upholstery
24/11271A-21
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting
B95
71A
II - FINAL OPERATION
a Refit:
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -Refitting, page 71A-32) ,
- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) .
8/6/2019 7 - Trim and Upholstery
25/11271A-22
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting
B95 or D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove the rear door upper sill trim (see 71A, Bodyinternal trim, Rear door sill upper lining: Remo-val - Refitting, page 71A-32) .
a Remove:
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) ,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-
36) ,
- the rear end panel trim (see 71A, Body internaltrim, Rear end panel lining: Removal - Refitting,page 71A-40) .
a Remove the rear parcel shelf side trim (see 71A ,Body internal trim, Rear parcel shelf side trim:Removal - Refitting, page 71A-38) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear wheel arch trim (1) .
a Remove the rear wheel arch trim (2) .
B95
D95
B95
137096
D95
137094
8/6/2019 7 - Trim and Upholstery
26/11271A-23
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting
B95 or D95
71A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit the rear wheel arch trim.
a Refit the rear wheel arch trim.
II - FINAL OPERATION
a Refit the rear parcel shelf side trim (see 71A, Bodyinternal trim, Rear parcel shelf side trim: Remo-val - Refitting, page 71A-38) .
a Refit:
- the rear end panel lining (see 71A, Body internaltrim, Rear end panel lining: Removal - Refitting,page 71A-40) ,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) ,
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) .
a Refit the rear door sill upper trim (see 71A, Body in-ternal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-32) .
B95
D95
D95
B95
8/6/2019 7 - Trim and Upholstery
27/11271A-24
BODY INTERNAL TRIM
A-pillar trim: Removal - Refitting
B95 or D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Partially remove the front side door seal.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Press using the tool (Car. 1363) at (1) .
a Remove the windscreen pillar trim (2) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the windscreen pillar trim.
Essential special tooling
Car. 1363 Set of trim removal levers.
137077
137091
8/6/2019 7 - Trim and Upholstery
28/11271A-25
BODY INTERNAL TRIM
A-pillar trim: Removal - Refitting
B95 or D95
71A
II - FINAL OPERATION
a Refit the front side door seal.
8/6/2019 7 - Trim and Upholstery
29/11271A-26
BODY INTERNAL TRIM
Rear roof drip moulding lining: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aTilt the rear bench seatback.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear side roof rail (1) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear side roof rail.
II - FINAL OPERATION
a Position the rear bench seatback.
137086
137089
8/6/2019 7 - Trim and Upholstery
30/11271A-27
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) ,
- the rear bench seat base (see Rear bench seatbase: Removal - Refitting) ,
- the door sill lining (see 71A, Body internal trim,Door sill lining: Removal - Refitting, page 71A-15) ,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) .
a Remove the trim (1) of the front side seat belt returnmechanism.
a Remove:
- the bolt (2) of the front side seat belt return mecha-nism,
- the front side seat belt return mechanism.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolts (3) of the B-pillar upper trim.
Tightening torquesm
bolt of the front side
seat belt return mecha-nism
21 N.m
137792
137793
137066
8/6/2019 7 - Trim and Upholstery
31/11271A-28
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
D95
71A
a Remove the B-pillar upper trim.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit the B-pillar upper trim.
II - FINAL OPERATION
a Refit the front side seat belt return mechanism.
a Torque tighten the bolt of the front side seat beltreturn mechanism (21 N.m).
a Refit:
- the trim of the front side seat belt return mecha-nism,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) ,
- the door sill lining (see 71A, Body internal trim,Door sill lining: Removal - Refitting, page 71A-15) ,
- the rear bench seat base (see Rear bench seatbase: Removal - Refitting) ,
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) .
137068
8/6/2019 7 - Trim and Upholstery
32/11271A-29
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-17) ,
- the rear door sill lining (see 71A , Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
- the B-pillar lower trim (see 71 A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-19) .
a Unclip the trim of the front side seat belt return me-chanism.
a Remove:
- the bolt (1) of the front side seat belt return mecha-nism,
- the front side seat belt return mechanism.
a Remove:
- the bolt (2) of the guide of the front side seat beltreturn mechanism,
- the guide of the front side seat belt return mecha-nism.
Tightening torquesm
bolt of the front side
seat belt return mecha-nism
21 N.m
137455
137457
137036
8/6/2019 7 - Trim and Upholstery
33/11271A-30
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
B95
71A
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Unclip the flap (3) using a flat-blade screwdriver.
a Apply pressure to (4) .
a Remove the B-pillar upper trim at (5) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the B-pillar upper trim.
a Clip on the flap (3).
137438
137072
137070
137062
8/6/2019 7 - Trim and Upholstery
34/11271A-31
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
B95
71A
II - FINAL OPERATION
a Refit:
- the guide of the front side seat belt return mecha-
nism,- the front side seat belt return mechanism,
a Torque tighten the bolt of the front side seat beltreturn mechanism (21 N.m).
a Refit:
- the trim of the front side seat belt return mecha-nism,
- the B-pillar lower trim (see 71 A, Body internal
trim, B-pillar lower trim: Removal - Refitting,page 71A-19)
- the rear door sill lining (see 71A, Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-20) ,
- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,
page 71A-17) .
8/6/2019 7 - Trim and Upholstery
35/11271A-32
BODY INTERNAL TRIM
Rear door sill upper lining: Removal - Refitting
B95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially remove the rear side door seal.
a Pull down the rear bench seat to the flat floor posi-tion.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear inner sill upper trim (1) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear inner sill upper trim.
II - FINAL OPERATION
a Move the rear bench seat to the normal position.
a Refit the rear side door seal.
137452
137453
8/6/2019 7 - Trim and Upholstery
36/11271A-33
BODY INTERNAL TRIM
C-pillar upper trim: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) ,
- the rear side roof rail (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) .
a Tilt the rear bench seatback.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the C-pillar upper trim (1) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit the C-pillar upper trim.
II - FINAL OPERATION
a Refit:
- the rear side roof rail (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) ,
- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) .
a Tilt the seat into its initial position.
137448
8/6/2019 7 - Trim and Upholstery
37/11271A-34
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting
B95 or D95
71A
REMOVAL
REMOVAL PREPARATION OPERATION
a Remove:
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) ,
- the rear inner sill upper trim (see 71A, Body inter-nal trim, Rear door sill upper lining: Removal -Refitting, page 71A-32) ,
- the bolt of the rear side seat belt lower mounting.
- the rear side seat belt lower mounting.
a Remove:
- the C-pillar upper trim (see 71A, Body internaltrim, C-pillar upper trim: Removal - Refitting,page 71A-33) ,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) ,
- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-38) .
OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear quarter panel trim (1) .
Tightening torquesm
bolt of the rear side seat
belt lower mounting
21 N.m
B95
D95
B95
137451
137450
8/6/2019 7 - Trim and Upholstery
38/11271A-35
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting
B95 or D95
71A
a Remove the rear quarter panel trim (2) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear quarter panel trim.
II - FINAL OPERATION
aRefit the rear side seat belt lower mounting.
a Torque tighten the bolt of the rear side seat beltlower mounting (21 N.m).
a Refit:
- the rear inner sill upper trim (see 71A, Body inter-nal trim, Rear door sill upper lining: Removal -Refitting, page 71A-32) ,
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) .
a Refit:
- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-38) ,
- the rear panel trim (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-
36) ,- the C-pillar upper trim (see 71A, Body internal
trim, C-pillar upper trim: Removal - Refitting,page 71A-33) .
D95
137448
137449
B95
D95
8/6/2019 7 - Trim and Upholstery
39/11271A-36
BODY INTERNAL TRIM
Rear panel trim: Removal - Refitting
D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Remove the 1/3 and 2/3 rear bench seat base (see1/3 and 2/3 rear bench seat:Removal - Refitting) .
a Remove the single unit rear bench seat base (see76A, Rear seat frames and mechanisms, Singleunit rear bench seat: Removal - Refitting, page76A-5) .
a Remove:
- the door sill lining (see 71A, Body internal trim,Door sill lining: Removal - Refitting, page 71A-15) ,
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) .
a Remove:
- the bolt (1) of the guide rail of the front side seatbelt return mechanism,
- the guide rail of the front side seat belt return me-chanism.
aTilt the rear bench seatback.
a Remove the rear panel upper trim.
Tightening torquesm
bolt of the guide rail of
the front side seat beltreturn mechanism
21 N.m
REAR BENCH FUNCTION or 1-2/3 REAR BENCHSEAT + ARMREST + N/R SEATBACK
REAR BENCH SEAT
137825
8/6/2019 7 - Trim and Upholstery
40/11271A-37
BODY INTERNAL TRIM
Rear panel trim: Removal - Refitting
D95
71A
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove:
- the bolt (2) of the rear panel trim,
- the rear panel trim partially.
a Disconnect the rear speaker connector (3) .
a Remove the rear panel trim.
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Connect the rear speaker connector.
a Refit the rear panel trim.
II - FINAL OPERATION
a Refit the rear panel upper trim.
a Fit the rear bench seatback.
a Refit the guide rail of the front side seat belt return
mechanism.
a Torque tighten the bolt of the guide rail of thefront side seat belt return mechanism (21 N.m).
a Refit:
- the side roof rail rear trim (see 71A, Body internaltrim, Rear roof drip moulding lining: Removal -Refitting, page 71A-26) ,
- the door sill lining (see 71A, Body internal trim,Door sill lining: Removal - Refitting, page 71A-15) .
a Refit the single unit rear bench seat base (see 76A,Rear seat frames and mechanisms, Single unitrear bench seat: Removal - Refitting, page 76A-5).
a Refit the 1/3 and 2/3 rear bench seat base (see 1/3
and 2/3 rear bench seat:Removal - Refitting) .
137446
137507
REAR BENCH SEAT
REAR BENCH FUNCTION or 1-2/3 REAR BENCHSEAT + ARMREST + N/R SEATBACK
8/6/2019 7 - Trim and Upholstery
41/11271A-38
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting
B95 or D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially remove the luggage compartment lid seal.
a Remove:
- the rear end panel (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36) ,
- the rear panel trim (see 71A, Body internal trim,
Rear panel trim: Removal - Refitting, page 71A-36) .
a Remove the luggage compartment light (see Lug-gage compartment light: Removal - Refitting)(81B, Interior lighting).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove:
- the bolts (1) ,
- the rear parcel shelf side trim (2) .
D95
B95
137439
137441
8/6/2019 7 - Trim and Upholstery
42/11271A-39
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting
B95 or D95
71A
a Remove:
- the bolts (3) ,
- the rear parcel shelf side trim (4) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the rear parcel shelf side trim,
- the bolts.
a Refit:
- the rear parcel shelf side trim,
- the bolts.
II - FINAL OPERATION
a Partially refit the luggage compartment lid seal.
a Refit:
- the rear panel trim, (see 71A, Body internal trim,Rear panel trim: Removal - Refitting, page 71A-36)
- the rear end panel (see 71A, Body internal trim,Rear end panel lining: Removal - Refitting, page71A-40) ,
a Refit:
- the luggage compartment light (see Luggagecompartment light: Removal - Refitting) (81B,Interior lighting),
- the luggage compartment lid seal.
D95
136672
137445
B95
D95
D95
8/6/2019 7 - Trim and Upholstery
43/11271A-40
BODY INTERNAL TRIM
Rear end panel lining: Removal - Refitting
B95 or D95
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:- the luggage compartment lid seal partially,
- the luggage compartment carpet.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear end panel trim at (1) and at (2) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear end panel trim.
II - FINAL OPERATION
a Refit:
- the luggage compartment carpet,
- the luggage compartment lid seal.
137440
137443
8/6/2019 7 - Trim and Upholstery
44/11272A-1
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the front window winder switch plate on the driver'sdoor (see Front electric window switches on dri-ver's door Removal - Refitting) (87D, Electricwindows - Sunroof) or the front window winderswitch plate on the passenger's door (see Frontelectric window switch on the passenger door:Removal - Refitting) (87D, Electric windows - Su-nroof),
- the lower door light (see Lower door light: Remo-val - Refitting) (81B, Interior lighting).
a Remove the trim of the front side door handle usingthe tool (Car. 1363) by inserting it at (1) .
a Remove the rear view mirror interior trim.
a Remove:
- the blanking cover (2) ,
- the bolt,
- the front side door interior handle (3) .
a Unclip the front side door interior opening control ca-ble.
Essential special tooling
Car. 1363 Set of trim removal levers.
D95
137392
137394
137404
8/6/2019 7 - Trim and Upholstery
45/11272A-2
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72AII - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolts (4) .
a Unclip the front side door trim at (5) and at (6) .
a Remove the front side door trim.
a Remove the screws.
a Unclip the front side door trim at (5) and at (6) .
a Remove the front side door trim.
D95
137407
137408
B95
137405
137406
8/6/2019 7 - Trim and Upholstery
46/11272A-3
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72AREFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Front side openingelement trim clip (70,03,02,22).
II - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
- the front door trim.
- the bolts (4).
III - FINAL OPERATION
a Clip on the front side door interior opening control
cable.
a Refit:
- the front side door interior handle (3),
- the bolt,
- the blanking cover (2),
- the rear view mirror interior trim.
a Refit the front side door handle trim.
a Refit:
- the lower door light (see Lower door light: Remo-
val - Refitting) (81B, Interior lighting),
- the front window winder switch plate on the driver's
door (see Front electric window switches on dri-
ver's door Removal - Refitting) (87D, Electric
windows - Sunroof) or the front window winder
switch plate on the passenger's door (see Front
electric window switch on the passenger door:
Removal - Refitting) (87D, Electric windows - Su-nroof).
a Carry out a function test.
D95
8/6/2019 7 - Trim and Upholstery
47/11272A-4
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting
B95
72A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove the rear door window winder switch plate(see Rear electric window switch: Removal - Re-fitting) (87D, Electric windows - Sunroof).
a Pull the ring towards the vehicle interior (1) .
REAR ELECTRIC WINDOW+ONE-TOUCH+ANTI-PINCH
MANUAL REAR WINDOW WINDER
137399
137400
8/6/2019 7 - Trim and Upholstery
48/11272A-5
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting
B95
72A
a Unfasten clip (2) .
a Remove the manual window winder control handle.
a Remove the lower door light (see Lower door light:Removal - Refitting) (81B, Interior lighting).
a Remove:
- the blanking cover (3) ,
- the bolt,
- the rear side door interior handle (4) .
a Unclip the rear side door interior opening release ca-
ble.
137396
137398
137403
8/6/2019 7 - Trim and Upholstery
49/11272A-6
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting
B95
72A
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Unclip the rear side door trim at (5) and at (6) .
a Remove the rear side door trim.
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Rear side openingelement trim clip (70,03,02,23).
II - REFITTING OPERATION FOR PARTCONCERNED
aRefit the rear side door trim.
III - FINAL OPERATION
a Clip on the rear side door interior opening releasecable.
a Refit:
- the rear side door interior handle (4),
- the bolt,
- the blanking cover (3),
- the lower door light (see Lower door light: Remo-val - Refitting) (81B, Interior lighting).
a Engage clip (2).
a Refit the manual window winder control handle.
a Refit the rear door window winder switch plate (seeRear electric window switch: Removal - Refit-
ting) (87D, Electric windows - Sunroof).
a Carry out a function test.
137402
MANUAL REAR WINDOW WINDER
REAR ELECTRIC WINDOW+ONE-TOUCH+ANTI-PINCH
8/6/2019 7 - Trim and Upholstery
50/11273A-1
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73AREMOVAL
OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the central trim.
a Remove the side trims.
a Remove:
- the bolts (1) ,
- the tailgate trim.
a Remove the central trim.
B95
137385
137387
137391
D95
137383
8/6/2019 7 - Trim and Upholstery
51/11273A-2
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73A
a Remove the side trims.
a Remove:
- the bolts (1) ,
- the tailgate trim.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a Refit:
- the tailgate trim,
- the side trims,
- the central trim.
137389
137395
8/6/2019 7 - Trim and Upholstery
52/11275A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
B95 or D95
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
a Remove:
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat base trim (see 77A, Front seat trim,Front seat base trim: Removal - Refitting, page77A-1) .
- the seat belt buckle (see Front seat belt buckle:Removal - Refitting) (88C, Airbags and pretensio-ners).
a Remove the anti-submarining airbag (see Anti-sub-marining airbag: Removal - Refitting) (88C, Air-bags and pretensioners).
a Remove the front seat lap belt pretensioner (seeFront seat lap belt pretensioner: Removal - Refit-ting) (88C, Airbag and pretensioners).
aRemove:- the front seat runners (see 75A, Front seat framesand mechanisms, Front seat runner: Removal -Refitting, page 75A-7) ,
- the front seat base pad,
- the electrical wiring.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolts (1) from the front seat seatback
- seat base frame.
Essential equipment
diagnostic tool
Tightening torquesm
frame bolts of the seatback - seat base forthe front seat
40 N.m
D95
B95
138035
8/6/2019 7 - Trim and Upholstery
53/11275A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
B95 or D95
75A
a
a
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Front seat seatbackframe mounting (70,08,02,09)
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit the front seat base frame.
a Torque tighten the frame bolts of the seat back -seat base for the front seat (40 N.m) .
III - FINAL OPERATION
a Refit:
- the electrical wiring,
FRONT SEAT TYPE 04
138034
Note:
The height adjustment motor mountings (2) can-not be removed. As the height adjustment motorcannot be removed, the Parts Department sup-plies the front seat base assembled with the hei-ght adjustment motor.
FRONT SEAT TYPE 01 or FRONT SEAT TYPE 02or FRONT SEAT TYPE 03
138033
Note:
The torsion bar (3) is on the pump module. The-refore, the pump module cannot be removed.The Parts Department supplies the front seatbase assembled with the pump module.
8/6/2019 7 - Trim and Upholstery
54/11275A-3
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
B95 or D95
75A
- the front seat base pad,
- the front seat runners (see 75A, Front seat framesand mechanisms, Front seat runner: Removal -Refitting, page 75A-7) .
a Refit the anti-submarining airbag (see Anti-subma-rining airbag: Removal - Refitting) (88C, Airbagsand pretensioners).
a Refit the front seat lap belt pretensioner (see Frontseat lap belt pretensioner: Removal - Refitting)(88C, Airbag and pretensioners).
a Refit:
- the seat belt buckle (see Front seat belt buckle:Removal - Refitting) (88C, Airbags and pretensio-ners),
- the front seat base trim (see 77A, Front seat trim,Front seat base trim: Removal - Refitting, page77A-1) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) .
a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).
a Apply the after repair procedure using the diagnos-tic tool :
- connect the diagnostic tool,
- select Driver's seat position storage and adjust-ment computer ,
- go to repair mode,
- display the Before/After repair procedure forthe computer selected,
- select the Driver's front seat base height adjust-ment instrumented rear motor ,
- carry out the operations described in the after re-pair procedure section.
a Carry out a function test.
D95
B95
FRONT SEAT TYPE 04
8/6/2019 7 - Trim and Upholstery
55/11275A-4
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
B95 or D95
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery : Removal -
Refitting) (80A, Battery).
a Remove:
- the headrest (see 79A, Seat components, Frontheadrest: Removal - Refitting, page 79A-1) ,
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat base casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) .
a Remove the rear seat access control (see Frontseat backrest tilt control: Removal - Refitting) .
a Remove the front seat lumbar adjustment control(see Front seat lumbar adjustment control: Re-
moval - Refitting) .
a Remove:
- the front seatback trim (see 77A, Front seat trim,Front seatback trim: Removal - Refitting, page77A-4) ,
- the headrest guides (see 79A, Seat components,Front seat headrest guide: Removal - Refitting,
page 79A-4) ,- the front seat side airbag (see Front (chest) sideairbag: Removal - Refitting) (88C, Airbag andpretensioners),
- the front seat lumbar adjustment (see 75A, Frontseat frames and mechanisms, Front seat lum-bar adjustment: Removal - Refitting, page 75A-11) .
a Unclip the rear seat access switch (1) .
a Disconnect the rear seat access connector.
a Remove the rear seat access switch.
a Remove:
- the rear seat access switch mounting (2) ,
Tightening torquesm
bolts of the seatback -
seat base frame of thefront seat
40 N.m
D95
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03or FRONT SEAT TYPE 04
D95, and FRONT SEAT TYPE 04
138058
138059
8/6/2019 7 - Trim and Upholstery
56/11275A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
B95 or D95
75A
- the front seatback angle motor (see 75A, Frontseat frames and mechanisms, Front seat bac-krest tilt motor: Removal - Refitting, page 75A-19) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolts (3) from the seatback - seat baseframe of the front seat
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Front seat seatbackframe mounting (70,08,02,09).
II - REFITTING OPERATION FOR PART
CONCERNED
a Refit the front seatback frame.
a Torque tighten the bolts of the seatback - seatbase frame of the front seat (40 N.m) .
III - FINAL OPERATION
a Refit:
- the front seatback angle motor (see 75A, Frontseat frames and mechanisms, Front seat bac-
krest tilt motor: Removal - Refitting, page 75A-19) ,
- the rear seat access switch mounting,
- the rear seat access switch.
a Connect the rear seat access switch connector.
a Refit:
- the front seat lumbar adjustment (see 75A, Frontseat frames and mechanisms, Front seat lum-bar adjustment: Removal - Refitting, page 75A-
11) ,
- the front seat side airbag (see Front (chest) sideairbag: Removal - Refitting) (88C, Airbag and
pretensioners),
- the headrest guides (see 79A, Seat components,Front seat headrest guide: Removal - Refitting,
page 79A-4) ,
- the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page77A-4) .
138049
138050
D95, and FRONT SEAT TYPE 04
8/6/2019 7 - Trim and Upholstery
57/11275A-6
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
B95 or D95
75A
aRefit the front seat lumbar adjustment control (seeFront seat lumbar adjustment control: Removal -Refitting) .
a Refit the rear seat access control (see Front seat
backrest tilt control: Removal - Refitting) .
a Refit:
- the front seat base casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the headrest (see 79A, Seat components, Frontheadrest: Removal - Refitting, page 79A-1) .
a Connect the battery (see Battery : Removal - Refit-ting) (80A, Battery).
a Carry out a function test.
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03or FRONT SEAT TYPE 04
D95
8/6/2019 7 - Trim and Upholstery
58/11275A-7
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
B95 or D95
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
a Remove:
- the front seat headrest (see 79A, Seat compo-nents, Front headrest: Removal - Refitting,
page 79A-1) ,- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat base casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-ting, page 77A-9) .
a Remove the front seat lap belt pretensioner (see
Front seat lap belt pretensioner: Removal - Refit-ting) (88C, Airbag and pretensioners).
a Partially remove the unlocking cable for the frontseat runners.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Unclip the front seat runner position sensor (1) .
Tightening torquesm
front seat runner nuts 21 N.m
B95
D95
138017
8/6/2019 7 - Trim and Upholstery
59/11275A-8
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
B95 or D95
75A
a Remove:
- the nuts of the frame for the front seat base -runner ,
- the front seat runners.
a Remove the front seat slide motor (see 75A, Frontseat frames and mechanisms, Front seat slidingmotor: Removal - Refitting, page 75A-14) .
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Front seat runnermounting on front seat frame (70,08,04,27).
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit the front seat runners.
a Finger tighten all the attachments.
a Position the runners so that there is a centre-to-cen-tre distance (X1) = 428.5 mm between the two rearmountings.
a Torque tighten the front seat runner nuts (21 N.m).
III - FINAL OPERATION
a Refit the front seat lap belt pretensioner (see Frontseat lap belt pretensioner: Removal - Refitting)(88C, Airbag and pretensioners).
a Refit the front seat position sensor.
aRefit:- the front seat lower casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
138018
138019
Note:
On the front seat belt buckle side, the nuts of the
frame for the front seat base - runner arelocated on the inside of the seat base frame.
FRONT SEAT TYPE 04
138020
B95
8/6/2019 7 - Trim and Upholstery
60/11275A-9
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
B95 or D95
75A
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat headrest (see 79A, Seat compo-
nents, Front headrest: Removal - Refitting,page 79A-1) .
a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).
8/6/2019 7 - Trim and Upholstery
61/11275A-10
FRONT SEAT FRAMES AND MECHANISMS
Front seat remote adjustment: Removal - Refitting
FRONT SEAT TYPE 01 or FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -
Refitting, page 75A-22) ,
- the front seat runners (see 75A, Front seat framesand mechanisms, Front seat remote adjust-ment: Removal - Refitting, page 75A-10) ,
- the front seat height adjustment control (see Front
seat height adjuster control: Removal - Refit-ting) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the torsion bar.
a Remove the mounting rivets from the height adjust-ment mechanism.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:- the front seat base,
- the front seat base trim (see 77A, Front seat trim,Front seat base trim: Removal - Refitting, page77A-1) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat height adjustment control (see Frontseat height adjuster control: Removal - Refit-ting) ,
- the front seat runners (see 75A, Front seat framesand mechanisms, Front seat runner: Removal -Refitting, page 75A-7) ,
- the front seat (see 75A, Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) .
Note:
The torsion bar is on the pump module. Therefore,
the pump module cannot be removed. The PartsDepartment supplies the front seat base assembledwith the pump module.
138033
8/6/2019 7 - Trim and Upholstery
62/11275A-11
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
a Remove:
- the front seat headrest (see 79A, Seat compo-nents, Front headrest: Removal - Refitting,page 79A-1) ,
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat base casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat lumbar adjustment control (see Frontseat lumbar adjustment control: Removal - Re-fitting) .
a Remove the rear seat access control (see Frontseat backrest tilt control: Removal - Refitting) .
a Remove the front seatback trim (see 77A, Frontseat trim, Front seatback trim: Removal - Refit-ting, page 77A-4) .
a Remove the front seat headrest guides (see 79A,Seat components, Front seat headrest guide:Removal - Refitting, page 79A-4) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolt (1) from the front seat lumbar ad-justment mechanism.
a Unclip the lumbar pad in the order indicated.
D95 138051
Note:
For this operation, the lumbar pad must be loose.
138023
8/6/2019 7 - Trim and Upholstery
63/11275A-12
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04
75A
a Remove the lumbar adjustment mechanism - lum-bar pad assembly.
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the lumbar adjustment mechanism - lumbarpad assembly.
a Clip on the lumbar pad in the order indicated.
a Carry out a function test.
II - FINAL OPERATION
a Refit the front seatback trim (see 77A, Front seattrim, Front seatback trim: Removal - Refitting,page 77A-4) .
a Refit the headrest guides (see 79A, Seat compo-nents, Front seat headrest guide: Removal - Re-fitting, page 79A-4) .
a Refit the rear seat access control (see Front seatbackrest tilt control: Removal - Refitting) .
a Refit:
- the front seat lumbar adjustment control (see Frontseat lumbar adjustment control: Removal - Re-
fitting) ,- the front seat base casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
138052
Note:
The Parts Department supplies the lumbaradjustment mechanism assembled with the lum-bar pad.
138053
Note:
The springs must be positioned on the framewith the hook facing the interior.
D95
8/6/2019 7 - Trim and Upholstery
64/11275A-13
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04
75A
- the front seat (see 75A , Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat headrest (see 79A, Seat compo-
nents, Front headrest: Removal - Refitting,page 79A-1) .
a Connect the battery (see Battery : Removal - Refit-ting) (80A, Battery).
8/6/2019 7 - Trim and Upholstery
65/11275A-14
FRONT SEAT FRAMES AND MECHANISMS
Front seat sliding motor: Removal - Refitting
B95 or D95, and FRONT SEAT TYPE 04
75A
REMOVAL
I - OPERATION FOR REMOVAL OF PARTCONCERNED
a Move the seat to the highest position.
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Disconnect the connectors from the front seat slidemotor.
a Unclip the rigid clip.
a Remove the runner motor with the long cable.
a Unclip the short cable.
aRemove the short cable.
Essential equipment
diagnostic tool
138014
138013
138016
138015
8/6/2019 7 - Trim and Upholstery
66/11275A-15
FRONT SEAT FRAMES AND MECHANISMS
Front seat sliding motor: Removal - Refitting
B95 or D95, and FRONT SEAT TYPE 04
75A
REFITTING
I - REFITTING PREPARATION OPERATION
a Check the condition of the cables.
a Show a good cable and a cable in poor condition
a Check that the right-hand and left-hand runners arecorrectly synchronised using a ruler.
a Use the cable to synchronise the runners.
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit the short cable fully into the runner mechanism.
a Refit the front seat slide motor.
a Refit the long cable fully into the runner mechanism.
a Refit the rigid clip.
a Connect the connectors.
III - FINAL OPERATION
a Connect the battery. (see Battery: Removal - Refit-ting)
a Apply the after repair procedure using the diagnos-tic tool :
- connect the diagnostic tool,
- select Driver's seat position storage and adjust-ment computer ,
- go to repair mode,
- display the Before/After repair procedure forthe computer selected,
135100
135099
Note:
Any damaged cables must always be replaced.
134068
Note:
A poorly inserted cable can cause runner syn-chronisation problems.
8/6/2019 7 - Trim and Upholstery
67/112
8/6/2019 7 - Trim and Upholstery
68/112
8/6/2019 7 - Trim and Upholstery
69/11275A-18
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjustment motor: Removal - Refitting
FRONT SEAT TYPE 04
75A
a Refit the front seat height adjustment motor (4) .
a Position the motor mounting (hole by hole) on theseat hinge (5) .
a Connect the connector of the seat height adjustmentmotor.
a Refit the bolt (1).
II - FINAL OPERATION
a Refit:
- the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -Refitting, page 75A-7) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) ,
- the front seat (see 75A, Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) .
a Connect the battery (see Battery : Removal - Refit-
ting) (80A, Battery).
a Apply the after repair procedure using the diagnos-
tic tool :
- connect the diagnostic tool,
- select driver's seat position storage and adjust-ment computer ,
- go to repair mode,
- display the Before/After repair procedure forthe selected computer,
- select driver's seat base height adjustment ins-trumented rear motor in the List of componentscontrolled by this computer section,
- carry out the operations described in the After re-pair procedure section,
- carry out a function test.
138151
138152
8/6/2019 7 - Trim and Upholstery
70/112
8/6/2019 7 - Trim and Upholstery
71/11275A-20
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting
B95 or D95, and FRONT SEAT TYPE 04
75A
II - REFITTING OPERATION FOR PARTCONCERNED
a Remove:
- the "claw shaft" clip,
- the mounting from the front seat base interior ca-sing.
a Partially remove the shaft.
a Remove the bolt from the front seatback angle mo-tor.
a Disconnect the connector from the front seatbackangle motor.
a Remove the motor.
138055
138061
138060
138057
8/6/2019 7 - Trim and Upholstery
72/11275A-21
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting
B95 or D95, and FRONT SEAT TYPE 04
75A
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the shaft on the seatback frame on the opposi-te side to the motor.
a Fit the motor on the shaft.
a Connect the connector of the front seatback anglemotor.
a Remove:
- the motor bolt,
- the shaft,
- the mounting of the front seat base interior casing,
- the new "claw shaft" clip on the angle shaft.
II - FINAL OPERATION
a Remove:
- the seatback trim (see 77A, Front seat trim, Frontseatback trim: Removal - Refitting, page 77A-4),
- the front seat base casing (see 77A , Front seattrim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) ,
- the headrest guides (see 79A, Seat components,
Front seat headrest guide: Removal - Refitting,page 79A-4) ,
- the front seat (see 75A, Front seat frames andmechanisms , Complete front seat: Removal -Refitting, page 75A-22) ,
- the front seat headrest (see 79A, Seat compo-nents, Front headrest: Removal - Refitting,page 79A-1) .
a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).
a Apply the after repair procedure using the diagnos-
tic tool :
- Connect the diagnostic tool,
- Select "Driver's seat position storage and adjust-ment computer",
- Display the "Before/After repair procedure" for thecomputer selected in the "List of components con-trolled by this computer" section,
- Perform the operations described in the "After re-pair procedure" section.
a Carry out a function test.
138056
138054
8/6/2019 7 - Trim and Upholstery
73/11275A-22
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
B95 or D95
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Adjust:
- the steering wheel to the highest position,
- the front seatback to the vertical position.
a Protect the front door sill linings with masking tape.
a Remove the front headrest (see 79A, Seat compo-nents, Front headrest: Removal - Refitting, page79A-1) .
a Disconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Move the seat back.
a Remove the seat bolts (1) .
a Move the seat forward.
a Remove the seat bolts (2) .
a Unclip the front seat belt using a flat-blade screwdri-ver.
Tightening torquesm
front seat bolts 35 N.m
138010
138011
B95
136727
8/6/2019 7 - Trim and Upholstery
74/11275A-23
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
B95 or D95
75A
a Mark the routing of the wiring on the floor.
a Tilt the front seat.
a Unclip the mounting (3) from the front seat wiring.
a Unlock the connector (4) .
a Disconnect the connector (4) .
a Remove the front seat (this operation requires twopeople).
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Front seat moun-ting on body (70,06,02,01).
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit the front seat (this operation requires two peo-
ple).
a Clip on the front seat wiring mounting.
a Connect the connector.
a Lock the connector.
a Refit the wiring in the position marked during the re-moval operation
a Clip the front seat belt onto the front seat lap beltpretensioner.
aTorque tighten the front seat bolts (35 N.m) .
a Refit the front headrest (see 79A , Seat compo-nents, Front headrest: Removal - Refitting, page79A-1) .
a Connect the battery (see Battery : Removal - Refit-ting) (80A, Battery).
138012
WARNING
To prevent any risk of noise, premature wear,short circuits, etc. after the refitting operation,mark the wiring routing and how to connect theconnectors.
Note:
Check that the lock lever is fully engaged
B95
8/6/2019 7 - Trim and Upholstery
75/11276A-1
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seatback: Removal - Refitting
B95 or D95, and REAR BENCH SEAT
76A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Lift:
- the single unit rear bench seat base,
- the rear section of the luggage compartment car-pet.
a Remove the rear seat belt buckle bolt (1) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the bolts (2) from the rear bench seatback.
a Remove the single unit rear bench seatback (3) then(4) (this operation requires two people).
Tightening torquesm
bolts of the rear bench
seatback
21 N.m
rear seat belt buckle bolt 21 N.m
136713
136693
136697
8/6/2019 7 - Trim and Upholstery
76/11276A-2
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seatback: Removal - Refitting
B95 or D95, and REAR BENCH SEAT
76A
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the single unit rear bench seatback (this operationrequires two people),
- the bolts of the rear bench seatback.
a Torque tighten the bolts of the rear bench seat-back (21 N.m).
II - FINAL OPERATION
a Refit the rear seat belt buckle bolt.
a Torque tighten the rear seat belt buckle bolt (21N.m).
a Refit:
- the single unit rear bench seat base,
- the rear section of the luggage compartment car-pet.
8/6/2019 7 - Trim and Upholstery
77/11276A-3
REAR SEAT FRAMES AND MECHANISMS
1/3 and 2/3 rear bench seatback: Removal - Refitting
B95 or D95, and REAR BENCH FUNCTION
76A
REMOVAL
I - OPERATION FOR REMOVAL OF PARTCONCERNED
a Lift:
- the 1/3 and 2/3 rear bench seat base,
- the rear section of the luggage compartment car-pet.
a Remove:
- the rear seat belt buckle bolt (1) ,
- the rear centre seat belt mounting.
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the front bolts (2) .
a Remove the bolt (3) of the 1/3 and 2/3 rear benchseatback.
Tightening torquesm
front bolts of the 1/3 and
2/3 rear bench seatback
21 N.m
rear bolt of the 1/3 and2/3 rear bench seatback
21 N.m
rear seat belt buckle bolt 21 N.m
136713
136693
136674
8/6/2019 7 - Trim and Upholstery
78/11276A-4
REAR SEAT FRAMES AND MECHANISMS
1/3 and 2/3 rear bench seatback: Removal - Refitting
B95 or D95, and REAR BENCH FUNCTION
76A
a Remove the 1/3 and 2/3 rear bench seatback (4)then (5) (this operation requires two people).
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
- the 1/3 and 2/3 rear bench seatback (this operationrequires two people),
- the front bolts of the 1/3 and 2/3 rear bench seat-back,
- the rear bolt of the 1/3 and 2/3 rear bench seat-back.
a Tighten to torque:
-the front bolts of the 1/3 and 2/3 rear benchseatback (21 N.m),
-the rear bolt of the 1/3 and 2/3 rear bench seat-back (21 N.m).
II - FINAL OPERATION
a Refit the rear seat belt buckle bolt.
a Torque tighten the rear seat belt buckle bolt (21N.m).
a Refit:
- the 1/3 and 2/3 rear bench seat base,
- the rear section of the luggage compartment car-pet.
136697
8/6/2019 7 - Trim and Upholstery
79/11276A-5
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seat: Removal - Refitting
B95 or D95, and REAR BENCH SEAT
76A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Tilt the single unit rear bench seat base.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a Remove the single unit rear bench seat base.
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the single unit rear bench seat base.
II - FINAL OPERATION
a Pull down the single unit rear bench seat seat base.
136700
136702
8/6/2019 7 - Trim and Upholstery
80/11276A-6
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback frame 1/3 and 2/3: Removal - Refitting
B95 or D95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
76A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove the luggage compartment carpet.
II - REFITTING OPERATION FOR PARTCONCERNED
a Remove the rear central armrest (see 79A, Seatcomponents, Rear centre arm rest: Removal -Refitting, page 79A-5) .
a Remove:
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) ,
- the 1/3 and 2/3 rear bench seatbacks (see 76A,Rear seat frames and mechanisms, 1/3 and 2/3rear bench seatback: Removal - Refitting, page76A-3) ,
- the rear headrests (see Rear headrest: Removal -Refitting) ,
- the 1/3 and 2/3 rear bench seat seatback trim (see78A, Rear seat trim, 1/3 and 2/3 rear bench seatseatback trim: Removal - Refitting, page 78A-3),
- the rear bench seat headrest guides (see 79A,Seat components, Rear seat headrest guide:Removal - Refitting, page 79A-6)
- the rear bench seat mechanism (see 76A , Rear
seat frames and mechanisms, Rear bench seatmechanism: Removal - Refitting, page 76A-7) ,
- the rear central seatbelt (see Rear centre seatbelt: Removal - Refitting) (88C, Airbag and pre-tensioners),
- the 1/3 and 2/3 rear bench seat base frame.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
- the 1/3 and 2/3 rear bench seat base frame.
- the rear central seatbelt (see Rear centre seatbelt: Removal - Refitting) (88C, Airbag and pre-tensioners),
- the rear bench seat mechanism (see 76A, Rear
seat frames and mechanisms, Rear bench seatmechanism: Removal - Refitting, page 76A-7) ,
- the rear bench seat headrest guides (see 79A,Seat components, Rear seat headrest guide:Removal - Refitting, page 79A-6) ,
- the 1/3 and 2/3 rear bench seat seatback trim (see78A, Rear seat trim, 1/3 and 2/3 rear bench seatseatback trim: Removal - Refitting, page 78A-3),
- the rear headrests (see Rear headrest: Removal -Refitting) ,
- the 1/3 and 2/3 rear bench seatbacks (see 76A,Rear seat frames and mechanisms, 1/3 and 2/3rear bench seatback: Removal - Refitting, page76A-3) ,
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) .
a Refit the rear central armrest (see 79A, Seat com-
ponents, Rear centre arm rest: Removal - Refit-ting, page 79A-5) .
II - FINAL OPERATION
a Refit the luggage compartment carpet.
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
8/6/2019 7 - Trim and Upholstery
81/11276A-7
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat mechanism: Removal - Refitting
B95 or D95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST +N/R SEATBACK
76A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the rear headrests (see Rear headrest: Removal -Refitting) ,
- the rear headrest guides (see 79A, Seat compo-nents, Rear seat headrest guide: Removal - Re-fitting, page 79A-6) .
a Remove:
- the single unit rear bench seatback (see 76A, Rearseat frames and mechanisms, Single unit rearbench seatback: Removal - Refitting, page 76A-1) ,
- the single unit rear bench seatback trim (see 78A,Rear seat trim, Rear bench seat single unitseatback trim: Removal - Refitting, page 78A-6).
a Remove:
- the 1/3 and 2/3 rear bench seatbacks (see 76A,Rear seat frames and mechanisms, 1/3 and 2/3rear bench seatback: Removal - Refitting, page76A-3) ,
- the rear central armrest (see 79A , Seat compo-nents, Rear centre arm rest: Removal - Refit-ting, page 79A-5) .
- the 1/3 and 2/3 rear bench seat seatback trim (see78A, Rear seat trim, 1/3 and 2/3 rear bench seatseatback trim: Removal - Refitting, page 78A-3).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove:
- the bolts (1) of the rear bench seat mechanism,
- the rear bench seat mechanism (2) .
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the rear bench seat mechanism (2),
- the bolts (1)of the rear bench seat mechanism.
Tightening torquesm
bolts of the rear benchseat mechanism
18 N.m
REAR BENCH FUNCTION
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
137427
8/6/2019 7 - Trim and Upholstery
82/11276A-8
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat mechanism: Removal - Refitting
B95 or D95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST +N/R SEATBACK
76A
a Torque tighten in order the bolts of the rear benchseat mechanism (18 N.m) (3) and (4) .
II - FINAL OPERATION
a Refit:
- the rear headrest guides (see 79A, Seat compo-nents, Rear seat headrest guide: Removal - Re-fitting, page 79A-6) ,
- the rear headrests (see Rear headrest: Removal -Refitting) .
a Refit:
- the single unit rear bench seatback trim (see 78A,Rear seat trim, Rear bench seat single unitseatback trim: Removal - Refitting, page 78A-6),
- the single unit rear bench seatback (see 76A, Rearseat frames and mechanisms, Single unit rearbench seatback: Removal - Refitting, page 76A-1) .
a Refit:
- the 1/3 and 2/3 rear bench seat seatback trim (see78A, Rear seat trim, 1/3 and 2/3 rear bench seatseatback trim: Removal - Refitting, page 78A-3),
- the rear central armrest (see 79A , Seat compo-nents, Rear centre arm rest: Removal - Refit-ting, page 79A-5) ,
- the 1/3 and 2/3 rear bench seatback (see 76A,Rear seat frames and mechanisms, 1/3 and 2/3
rear bench seatback: Removal - Refitting, page76A-3) .
a Carry out a function test.137427
REAR BENCH FUNCTION
1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK
8/6/2019 7 - Trim and Upholstery
83/11276A-9
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat single-unit seatback frame: Removal - Refitting
B95 or D95, and REAR BENCH SEAT
76A
REMOVAL
OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove:
- the rear headrests (see Rear headrest: Removal -Refitting) ,
- the single unit rear bench seatback (see 76A, Rearseat frames and mechanisms, Single unit rearbench seatback: Removal - Refitting, page 76A-1) ,
- the rear bench seat single unit seatback trim (see78A, Rear seat trim, Rear bench seat single unitseatback trim: Removal - Refitting, page 78A-6)
,
- the rear bench seat headrest guides (see 79A,Seat components, Rear seat headrest guide:Removal - Refitting, page 79A-6) ,
- the rear central seatbelt (see Rear centre seatbelt: Removal - Refitting) (88C, Airbags and pre-tensioners),
- the rear bench seat mechanisms (see 76A, Rearseat frames and mechanisms, Rear bench seatmechanism: Removal - Refitting, page 76A-7) ,
- the single unit rear bench seatback frame.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a Refit:
- the single unit rear bench seatback frame.
- the rear bench seat mechanisms (see 76A, Rear
seat frames and mechanisms, Rear bench seatmechanism: Removal - Refitting, page 76A-7) ,
- the rear central seatbelt (see Rear centre seatbelt: Removal - Refitting) (88C, Airbags and pre-tensioners),
- the rear bench seat headrest guides (see 79A,Seat components, Rear seat headrest guide:Removal - Refitting, page 79A-6) ,
- the rear bench seat single unit seatback trim (see78A, Rear seat trim, Rear bench seat single unitseatback trim: Removal - Refitting, page 78A-6),
- the single unit rear bench seatback (see 76A, Rearseat frames and mechanisms, Single unit rearbench seatback: Removal - Refitting, page 76A-1) ,
- the rear headrests (see Rear headrest: Removal -Refitting) ,
8/6/2019 7 - Trim and Upholstery
84/11277A-1
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
B95 or D95
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
a Remove:
- the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-moval - Refitting, page 75A-22) ,
- the front seat lower casings (see 77A, Front seattrim, Front seat lower cover: Removal - Refit-ting, page 77A-9) .
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the elastic strap of the seatback cover.
a Remove the retaining section at 1.
Essential special tooling
Car. 1363 Set of trim removal levers.
137996
138019
118675
8/6/2019 7 - Trim and Upholstery
85/112
8/6/2019 7 - Trim and Upholstery
86/11277A-3
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
B95 or D95
77A
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the front seat base cover,
- the "foam - cover" assembly of the front seat base,
- the retaining sections
- Align the velcro strips.
a Connect the heated pad connector.
a Refit:
- the clips,
- the elastic strap.
III - FINAL OPERATION
a Refit:
- the seat lower casings (see 77A, Front seat trim,Front seat lower cover: Removal - Refitting,page 77A-9) ,
- the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-val - Refitting, page 75A-22) .
a Connect the battery (see Battery : Removal - Refit-ting) (80A, Battery).
138022
FRONT SEAT WITH HEATING
8/6/2019 7 - Trim and Upholstery
87/11277A-4
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
B95 or D95
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery : Removal -Refitting) (80A, Battery).
a Remove:
- the front headrest (see 79A, Seat components,Front headrest: Removal - Refitting, page 79A-1) ,
- the front seat (see 75A , Front seat frames andmechanisms , Complete front s