CAUTION: It is advised that normal static precautions be taken in handling and assemblyof this component to prevent damage and/or degradation which may be induced by ESD.Features15 kV/s minimum Common Mode Rejection (CMR) at VCM = 1 kV for HCNW2611, HCPL-2611, HCPL-4661, HCPL-0611, HCPL-0661High speed: 10 MBd typicalLSTTL/TTL compatibleLow input current capability: 5 mAGuaranteed AC and DC performance over temper-ature:-40 C to +85 CAvailable in 8-Pin DIP, SOIC-8, widebody packagesStrobable output (single channel products only)Safety approval UL recognized - 3750 Vrms for 1 minute and 5000Vrms* for 1 minute per UL1577 CSA approved IEC/EN/DIN EN 60747-5-5approved with VIORM = 567 Vpeak for 06xx Option 060VIORM = 630 Vpeak for 6N137/26xx Option 060 VIORM = 1414 Vpeak for HCNW137/26x1MIL-PRF-38534 hermetic version available(HCPL-56xx/66xx)ApplicationsIsolated line receiverComputer-peripheral interfacesMicroprocessor system interfacesDigital isolation for A/D, D/A conversionSwitching power supplyInstrument input/output isolationGround loop eliminationPulse transformer replacementPower transistor isolation in motor drivesIsolation of high speed logic systemsFunctional Diagram*5000 Vrms/1 Minute rating is for HCNW137/26X1 and Option 020 (6N137, HCPL-2601/11/30/31, HCPL-4661) products only.A 0.1 F bypass capacitor must be connected between pins 5 and 8.6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600,HCPL-0601, HCPL-0611, HCPL-0630, HCPL-0631, HCPL-0661,HCPL-2601, HCPL-2611, HCPL-2630, HCPL-2631, HCPL-4661High CMR, High Speed TTL Compatible OptocouplersData Sheet DescriptionThe6N137,HCPL-26xx/06xx/4661,HCNW137/26x1are optically coupled gates that combine a GaAsP light emit-tingdiodeandanintegratedhighgainphotodetector. Anenableinputallowsthedetectortobestrobed. The output of the detector IC is an open collector Schottky-clampedtransistor. Theinternalshieldprovidesaguar-anteed common mode transient immunity specifcation up to 15,000 V/sat Vcm = 1000 V.This unique design provides maximum AC and DC circuit isolation while achieving TTL compatibility. The optocou-plerACandDCoperationalparam e tersareguaranteed from-40Cto+85Callowingtroublefreesystemper-formance.Lead (Pb) FreeRoHS 6 fullycompliantRoHS 6 fully compliant options available;-xxxE denotes a lead-free product12348765CATHODEANODEGNDVVCCO12348765 ANODE 2CATHODE 2CATHODE 1ANODE 1GNDVVCCO2VEVO16N137, HCPL-2601/2611HCPL-0600/0601/0611HCPL-2630/2631/4661HCPL-0630/0631/0661NCNCLEDONOFFONOFFONOFFENABLEHHLLNCNCOUTPUTLHHHLHTRUTH TABLE(POSITIVE LOGIC)LEDONOFFOUTPUTLHTRUTH TABLE(POSITIVE LOGIC)SHIELD SHIELD2The 6N137, HCPL-26xx, HCPL-06xx, HCPL-4661, HCNW137, and HCNW26x1 are suitable for high speed logic interfac-ing, input/output bufering, as line receivers in environ-mentsthatconventionallinereceiverscannottolerate and are recom mended for use in extremely high ground or induced noise environments.Selection GuideWidebody Minimum CMR8-Pin DIP (300 Mil)Small-Outline SO-8(400 Mil)HermeticInputSingle On-SingleDualSingleDualSingleand Dual dV/dtVCMCurrentOutputChannelChannelChannelChannelChannelChannel (V/s)(V)(mA)EnablePackagePackagePackagePackagePackagePackages1000105YES6N137 5,0001,0005YESHCPL-0600HCNW137NOHCPL-2630HCPL-063010,0001,000YESHCPL-2601HCPL-0601HCNW2601NOHCPL-2631HCPL-063115,0001,000YESHCPL-2611HCPL-0611HCNW2611NOHCPL-4661HCPL-06611,00050YESHCPL-2602[1]3, 500300YESHCPL-2612[1]1,000503YESHCPL-261A[1]HCPL-061A[1]NOHCPL-263A[1]HCPL-063A[1]1,000[2]1,000YESHCPL-261N[1]HCPL-061N[1]NOHCPL-263N[1]HCPL-063N[1]1,0005012.5 [3]HCPL-193x[1] HCPL-56xx[1] HCPL-66xx[1]Notes:1.Technical data are on separate Avago publications.2.15 kV/s with VCM = 1 kV can be achieved using Avago application circuit.3.Enable is available for single channel products only, except for HCPL-193x devices.3Ordering InformationHCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577.HCNWxxxx is UL Rcognized with 5000 Vrms for 1 minute per UL1577. PartNumberOptionPackageSurfaceMountGullWingTape &ReelUL 5000 Vrms/1 MinuteRatingIEC/EN/DINEN 60747-5-5 QuantityRoHSCompliantNon RoHSCompliant6N137-000E No option300milDIP-850 per tube-300E #300 X X 50 per tube-500E #500 X X X 1000 per reel-020E #020 X 50 per tube-320E #320 X X X 50 per tube-520E #520 X X X X 1000 per reel-060E #060 X 50 per tube-560E -560 X X X X 1000 per reelHCPL-2601-000E No option300milDIP-850 per tube-300E #300X X 50 per tube-500E #500 X X X 1000 per reel-020E #020 X 50 per tube-320E #320 X X X 50 per tube-520E #520 X X X X 1000 per reel-060E #060 X 50 per tube-360E - X X X 50 per tubeHCPL-2611-000E No option300milDIP-850 per tube-300E #300 X X 50 per tube-500E #500 X X X 1000 per reel-020E #020 X 50 per tube-320E #320 X X X 50 per tube-520E #520 X X X X 1000 per reel-060E #060 X 50 per tube-360E #360 X X X 50 per tube-560E #560 X X X X 1000 per reelHCPL-2630-000E No option300milDIP-850 per tube-300E #300 X X 50 per tube-500E #500 X X X 1000 per reel-020E #020 X 50 per tube-320E #320 X X X 50 per tube-520E -520 X X X X 1000 per reelHCPL-2631HCPL-4661-000E No option300milDIP-850 per tube-300E #300 X X 50 per tube-500E #500 X X X 1000 per reel-020E #020 X 50 per tube-320E #320 X X X 50 per tube-520E #520 X X X X 1000 per reel4SchematicSHIELD8652+36N137 Schematic aVFUSE OF A 0.1 F BYPASS CAPACITOR CONNECTEDBETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5).IFICCVCCVOGNDIOVEIE 76N137, HCPL-2601/2611HCPL-0600/0601/0611HCNW137, HCNW2601/2611SHIELD87+26N137 Schematic bVF1IF1ICCVCCVO1IO11SHIELD654VF2+IF2VO2GNDIO23HCPL-2630/2631/4661HCPL-0630/0631/0661PartNumberOptionPackageSurfaceMountGullWingTape &ReelUL 5000 Vrms/1 MinuteRatingIEC/EN/DINEN 60747-5-5 QuantityRoHSCompliantNon RoHSCompliantHCPL-0600HCPL-0601HCPL-0611-000E No optionSO-8X 100 per tube-500E #500 X X 1500 per reel-060E #060 X X 100 per tube-560E #560 X X X 1500 per reelHCPL-0630HCPL-0631HCPL-0661-000E No optionSO-8X 100 per tube-500E #500 X X 1500 per reelHCNW137HCNW2601HCNW2611-000E No option400 mil DIP-8X X 42 per tube-300E #300 X X X X 42 per tube-500E #500 X X X X X 750 per reelTo order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Combination of Option 020 and Option 060 is not available.Example 1: HCPL-2611-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packag ing with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.Example 2: HCPL-2630 to order product of 300mil DIP package in tube packaging and non RoHS compliant.Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.Notes: The notation #xxx is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant option will use -xxxE.5Package Outline Drawings8-pin DIP Package** (6N137, HCPL-2601/11/30/31, HCPL-4661)8-pin DIP Package with Gull Wing Surface Mount Option 300 (6N137, HCPL-2601/11/30/31, HCPL-4661)**JEDEC Registered Data (for 6N137 only).0.635 0.25(0.025 0.010)12 NOM.9.65 0.25(0.380 0.010)0.635 0.130(0.025 0.005)7.62 0.25(0.300 0.010)5 6 7 84 3 2 19.65 0.25(0.380 0.010)6.350 0.25(0.250 0.010)1.016 (0.040)1.27 (0.050)10.9 (0.430)2.0 (0.080)LAND PATTERN RECOMMENDATION1.080 0.320(0.043 0.013)1.780(0.070)MAX.1.19(0.047)MAX.2.54(0.100)BSCDIMENSIONS IN MILLIMETERS (INCHES).LEAD COPLANARITY = 0.10 mm (0.004 INCHES).0.254+ 0.076- 0.051(0.010+ 0.003)- 0.002)NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.3.56 0.13(0.140 0.005)1.080 0.320(0.043 0.013)2.54 0.25(0.100 0.010)0.51 (0.020) MIN.0.65 (0.025) MAX.4.70 (0.185) MAX.2.92 (0.115) MIN.5 TYP.0.254+ 0.076- 0.051(0.010+ 0.003)- 0.002)7.62 0.25(0.300 0.010)6.35 0.25(0.250 0.010)9.65 0.25(0.380 0.010)1.78 (0.070) MAX.1.19 (0.047) MAX.DIMENSIONS IN MILLIMETERS (INCHES).5 6 7 84 3 2 1*MARKING CODE LETTER FOR OPTION NUMBERS"L" = OPTION 020"V" = OPTION 060OPTION NUMBERS 300 AND 500 NOT MARKED.NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.3.56 0.13(0.140 0.005)EEENNNNYYWWATEST RATING CODE ZPDEVICE PART NUMBERUL LOGOSPECIAL PROGRAM CODELEAD-FREEAVAGO LOT IDDATE CODEPIN 16Small-Outline SO-8 Package (HCPL-0600/01/11/30/31/61)8-Pin Widebody DIP Package (HCNW137, HCNW2601/11)7.49 (0.295)1.9 (0.075)0.64 (0.025)LAND PATTERN RECOMMENDATION8 7 6 54 3 2 15.994 0.203(0.236 0.008)3.937 0.127(0.155 0.005)0.406 0.076(0.016 0.003)1.270(0.050)BSC5.080 0.127(0.200 0.005)3.175 0.127(0.125 0.005)1.524(0.060)45 X0.432(0.017)0.228 0.025(0.009 0.001)0.305(0.012)MIN.TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)5.207 0.254 (0.205 0.010)DIMENSIONS IN MILLIMETERS (INCHES).LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.0.203 0.102(0.008 0.004)70 ~ 7**YYWWNNNN ZEEETEST RATING CODEDEVICE PART NUMBERLEAD-FREELOT IDDATE CODEPIN 15 6 7 84 3 2 111.23 0.15(0.442 0.006)1.80 0.15(0.071 0.006)5.10(0.201)MAX.1.55(0.061)MAX.2.54 (0.100)TYP.DIMENSIONS IN MILLIMETERS (INCHES).NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.7 TYP.0.254+ 0.076- 0.0051(0.010+ 0.003)- 0.002)11.00(0.433)9.00 0.15(0.354 0.006)MAX.10.16 (0.400)TYP.0.51 (0.021) MIN.0.40 (0.016)0.56 (0.022)3.10 (0.122)3.90 (0.154)NNNNNNNNYYWWAEEEZAVAGO TEST RATING CODEDATE CODELOT IDDEVICE PART NUMBERLEAD-FREEPIN 178-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300(HCNW137, HCNW2601/11)Refow Soldering Profle1.00 0.15(0.039 0.006)7 NOM.12.30 0.30(0.484 0.012)0.75 0.25(0.030 0.010)11.00(0.433)5 6 7 84 3 2 111.23 0.15(0.442 0.006)9.00 0.15(0.354 0.006)1.3(0.051)13.56(0.534)2.29(0.09)LAND PATTERN RECOMMENDATION1.80 0.15(0.071 0.006)4.00(0.158)MAX.1.55(0.061)MAX.2.54(0.100)BSCDIMENSIONS IN MILLIMETERS (INCHES).LEAD COPLANARITY = 0.10 mm (0.004 INCHES).NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.0.254+ 0.076- 0.0051(0.010+ 0.003)- 0.002)MAX.TherecommendedrefowsolderingconditionsareperJEDECStandardJ-STD-020(latestrevision).Non-halidefux should be used.Regulatory InformationThe 6N137, HCPL-26xx/06xx/46xx, and HCNW137/26xx have been approved by the following organizations:ULRecognized under UL 1577, Component Recognition Program, File E55361.CSAApproved under CSA Component Acceptance Notice #5, File CA 88324.IEC/EN/DIN EN 60747-5-5Test Rating Code, Z Optional Identifcation CodeL Option x2xV Option x5x or x6xA Avago UL LogoP Special Program Code8Insulation and Safety Related Specifcations8-pin DIPWidebody (300 Mil)SO-8(400 Mil) Parameter SymbolValueValueValueUnitConditionsMinimum ExternalL(101)7.14.99.6mmMeasured from input terminals Air Gapto output terminals, shortest (External Clearance)distance through air.Minimum ExternalL(102)7.44.810.0mmMeasured from input terminals Trackingto output terminals, shortest (External Creepage)distance path along body.Minimum Internal0.080.081.0mmThrough insulation distance, Plastic Gapconductor to conductor, usually (Internal Clearance)the direct distance between the photoemitter and photodetector inside the optocoupler cavity.Minimum InternalNANA4.0mmMeasured from input terminals Trackingto output terminals, along(Internal Creepage)internal cavity.Tracking ResistanceCTI200200200VDIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index)Isolation GroupIIIaIIIaIIIaMaterial Group (DIN VDE 0110, 1/89, Table 1)Option 300 - surface mount classifcation is Class A in accordance with CECC 00802.IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (HCPL-06xx Option 060 Only) DescriptionSymbolCharacteristicUnitInstallation classifcation per DIN VDE 0110, Table 1 for rated mains voltage 150 VrmsI-IV for rated mains voltage 300 VrmsI-IV for rated mains voltage 600 VrmsI-III Climatic Classifcation40/85/21 Pollution Degree (DIN VDE 0110/39)2 Maximum Working Insulation VoltageVIORM567V peakInput-to-Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,VPR1063V peak Partial Discharge < 5 pCInput-to-Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec, VPR907V peak Partial Discharge < 5 pCHighest Allowable Overvoltage (Transient Overvoltage, tini = 60 sec)VIOTM6000V peakSafety Limiting Values (Maximum values allowed in the event of a failure) Case TemperatureTS150C Input Current**IS,INPUT150mA Output Power**PS,OUTPUT600mWInsulation Resistance at TS, VIO = 500 VRS109*Refertothefrontoftheoptocouplersectionofthecurrentcatalog,underProductSafetyRegulationssection,IEC/EN/DINEN60747-5-5,fora detailed description.Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.9IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (HCPL-26xx; 46xx; 6N13x Option 060 Only) DescriptionSymbolCharacteristicUnitInstallation classifcation per DIN VDE 0110, Table 1 for rated mains voltage 300 VrmsI-IV for rated mains voltage 450 VrmsI-IV Climatic Classifcation40/85/21 Pollution Degree (DIN VDE 0110/39)2 Maximum Working Insulation VoltageVIORM630V peakInput to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,VPR1181V peak Partial Discharge < 5 pCInput to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and sample test, tm = 10 sec, VPR1008V peak Partial Discharge < 5 pCHighest Allowable Overvoltage (Transient Overvoltage, tini = 60 sec)VIOTM6000V peakSafety Limiting Values (Maximum values allowed in the event of a failure) Case TemperatureTS175C Input CurrentIS,INPUT230mA Output PowerPS,OUTPUT600mWInsulation Resistance at TS, VIO = 500 VRS109*Refertothefrontoftheoptocouplersectionofthecurrentcatalog,underProductSafetyRegulationssection,IEC/EN/DINEN60747-5-5,fora detailed description.Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (HCNW137/2601/2611 Only) DescriptionSymbolCharacteristicUnitInstallation classifcation per DIN VDE 0110, Table 1 for rated mains voltage 600 VrmsI-IV for rated mains voltage 1000 VrmsI-III Climatic Classifcation40/85/21 Pollution Degree (DIN VDE 0110/39)2 Maximum Working Insulation VoltageVIORM1414V peakInput to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,VPR2651V peak Partial Discharge < 5 pCInput to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and sample test, tm = 10 sec, VPR2262V peak Partial Discharge < 5 pCHighest Allowable Overvoltage (Transient Overvoltage, tini = 60 sec)VIOTM8000V peakSafety Limiting Values (Maximum values allowed in the event of a failure) Case TemperatureTS150C Input CurrentIS,INPUT400mA Output PowerPS,OUTPUT700mWInsulation Resistance at TS, VIO = 500 VRS109*Refertothefrontoftheoptocouplersectionofthecurrentcatalog,underProductSafetyRegulationssection,IEC/EN/DINEN60747-5-5,fora detailed description.Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.10Absolute Maximum Ratings* (No Derating Required up to 85 C)ParameterSymbolPackage**Min.Max.UnitsNoteStorage TemperatureTS-55125COperating TemperatureTA-4085CAverage Forward Input CurrentIFSingle 8-Pin DIP20mA2 Single SO-8 WidebodyDual 8-Pin DIP151, 3 Dual SO-8Reverse Input VoltageVR8-Pin DIP, SO-85V1Widebody3Input Power DissipationPIWidebody40mWSupply VoltageVCC7V (1 Minute Maximum)Enable Input Voltage (Not toVESingle 8-Pin DIPVCC + 0.5V Exceed VCC by more thanSingle SO-8 500 mV)WidebodyEnable Input CurrentIE5mAOutput Collector CurrentIO50mA1Output Collector VoltageVO7V1Output Collector PowerPOSingle 8-Pin DIP85mW DissipationSingle SO-8 WidebodyDual 8-Pin DIP601, 4 Dual SO-8Lead Solder TemperatureTLS8-Pin DIP260 C for 10 sec., (Through Hole Parts Only) 1.6 mm below seating planeWidebody260 C for 10 sec., up to seating planeSolder Refow Temperature SO-8 andSee Package Outline Profle (Surface Mount Parts Only)Option 300Drawings section *JEDEC Registered Data (for 6N137 only).**Ratings apply to all devices except otherwise noted in the Package column.0 C to 70 C on JEDEC Registration.Recommended Operating ConditionsParameterSymbolMin.Max.UnitsInput Current, Low LevelIFL*0250AInput Current, High Level[1]IFH**515mAPower Supply VoltageVCC4.55.5VLow Level Enable VoltageVEL00.8VHigh Level Enable VoltageVEH2.0VCCVOperating TemperatureTA-4085CFan Out (at RL = 1 k)[1]N5TTL LoadsOutput Pull-up ResistorRL3304 k*The of condition can also be guaranteed by ensuring that VFL 0.8 V.**The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband.For single channel products only.11Electrical SpecifcationsOver recommended temperature (TA = -40 C to +85 C) unless otherwise specifed. All Typicals at VCC = 5 V, TA = 25 C. All enable test conditions apply to single channel products only. See note 5.ParameterSym.PackageMin.Typ.Max.Units Test ConditionsFig. NoteHigh Level OutputIOH*All5.5100AVCC = 5.5 V, VE = 2.0 V,11, 6, CurrentVO = 5.5 V, IF = 250 A19Input ThresholdITHSingle Channel2.05.0mAVCC = 5.5 V, VE = 2.0 V,2, 319 CurrentWidebodyVO = 0.6 V, Dual Channel2.5 IOL (Sinking) = 13 mALow Level OutputVOL*8-Pin DIP0.350.6VVCC = 5.5 V, VE = 2.0 V,2, 3,1, 19 VoltageSO-8IF = 5 mA,4, 5 Widebody0.4IOL (Sinking) = 13 mAHigh Level SupplyICCHSingle Channel7.010.0*mAVE = 0.5 V VCC = 5.5 V 7 Current6.5VE = VCCIF = 0 mA Dual Channel1015Both ChannelsLow Level SupplyICCLSingle Channel9.013.0*mAVE = 0.5 V VCC = 5.5 V 8 Current8.5VE = VCCIF = 10 mA Dual Channel1321Both ChannelsHigh Level EnableIEHSingle Channel-0.7-1.6mAVCC = 5.5 V, VE = 2.0 V CurrentLow Level EnableIEL*-0.9-1.6mAVCC = 5.5 V, VE = 0.5 V9 CurrentHigh Level EnableVEH2.0V19 VoltageLow Level EnableVEL0.8V VoltageInput ForwardVF8-Pin DIP1.41.51.75*VTA = 25 C IF = 10 mA6, 71 VoltageSO-81.31.80 Widebody1.251.641.85TA = 25 C 1.22.05Input ReverseBVR*8-Pin DIP5VIR = 10 A1 BreakdownSO-8 VoltageWidebody3IR = 100 A, TA = 25CInput DiodeDVF/ 8-Pin DIP-1.6mV/C IF = 10 mA71 TemperatureTASO-8 CoefcientWidebody-1.9Input CapacitanceCIN8-Pin DIP60pFf = 1 MHz, VF = 0 V1 SO-8 Widebody70*JEDEC registered data for the 6N137. The JEDEC Registration specifes 0 C to +70 C. Avago specifes -40 C to +85 C.12Switching Specifcations (AC)Over Recommended Temperature (TA = -40 C to +85 C), VCC = 5 V, IF = 7.5 mA unless otherwise specifed. All Typicals at TA = 25 C, VCC = 5 V.ParameterSym.Package**Min.Typ.Max.Units Test ConditionsFig. NotePropagation DelaytPLH204875*nsTA = 25C RL = 350 8, 9,1, 10, Time to High100CL = 15 pF1019 Output LevelPropagation DelaytPHL255075*nsTA = 25C1, 11, Time to Low10019 Output LevelPulse Width|tPHL - tPLH|8-Pin DIP3.535ns8, 9,13, 19 DistortionSO-810, Widebody4011Propagation DelaytPSK40ns12, 13, Skew19Output Risetr24ns121, 19 Time (10-90%)Output Falltf10ns121, 19 Time (90-10%)Propagation DelaytELHSingle Channel30nsRL = 350 ,13,14 Time of EnableCL = 15 pF,14 from VEH to VEL VEL = 0 V, VEH = 3 VPropagation DelaytEHLSingle Channel20ns15 Time of Enable from VEL to VEH*JEDEC registered data for the 6N137.**Ratings apply to all devices except otherwise noted in the Package column.ParameterSym.DeviceMin.Typ.Units Test ConditionsFig.NoteLogic High|CMH|6N1371,00010,000V/s|VCM| = 10 VVCC = 5 V, IF = 0 mA,151, 16, CommonHCPL-26305,00010,000|VCM| = 1 kVVO(MIN) = 2 V,18, 19 ModeHCPL-0600/0630RL = 350 , TA = 25 C TransientHCNW137 ImmunityHCPL-2601/263110,00015,000|VCM| = 1 kV HCPL-0601/0631 HCNW2601 HCPL-2611/466115,00025,000|VCM| = 1 kV HCPL-0611/0661 HCNW2611Logic Low|CML|6N1371,00010,000V/s|VCM| = 10 VVCC = 5 V, IF = 7.5 mA,151, 17, CommonHCPL-26305,00010,000|VCM| = 1 kVVO(MAX) = 0.8 V,18, 19 ModeHCPL-0600/0630RL = 350 , TA = 25C TransientHCNW137 ImmunityHCPL-2601/263110,00015,000|VCM| = 1 kV HCPL-0601/0631 HCNW2601 HCPL-2611/466115,00025,000|VCM| = 1 kV HCPL-0611/0661 HCNW261113Package CharacteristicsAll Typicals at TA = 25 C.ParameterSym. PackageMin.Typ.Max.UnitsTest ConditionsFig.NoteInput-OutputII-O*Single 8-Pin DIP1A45% RH, t = 5 s,20, 21 InsulationSingle SO-8VI-O = 3 kV dc, TA = 25 CInput-OutputVISO8-Pin DIP, SO-83750V rmsRH 50%, t = 1 min,20, 21 Momentary With-Widebody5000TA = 25 C20, 22 stand Voltage**OPT 0205000Input-OutputRI-O8-Pin DIP, SO-81012VI-O = 500 Vdc1, 20, ResistanceWidebody10121013TA = 25 C23 1011TA = 100 CInput-OutputCI-O8-Pin DIP, SO-80.6pFf = 1 MHz, TA = 25 C1, 20, CapacitanceWidebody0.50.623Input-InputII-IDual Channel0.005ARH 45%, t = 5 s,24 InsulationVI-I = 500 V Leakage CurrentResistanceRI-IDual Channel101124 (Input-Input)CapacitanceCI-IDual 8-Pin DIP0.03pFf = 1 MHz24 (Input-Input)Dual SO-80.25 *JEDEC registered data for the 6N137. The JEDEC Registration specifes 0 C to 70 C. Avago specifes -40 C to 85 C.**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous volt-age rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment level safety specifcation or Avago Application Note 1074 entitled Optocoupler Input-Output Endurance Voltage.For 6N137, HCPL-2601/2611/2630/2631/4661 only.Notes:1.Each channel.2.Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 20 mA.3.Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 15 mA.4.Derate linearly above 80 C free-air temperature at a rate of 2.7 mW/C for the SOIC-8 package.5.Bypassing of the power supply line is required, with a 0.1 F ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 17. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.6.The JEDEC registration for the 6N137 specifes a maximum IOH of 250 A. Avago guarantees a maximum IOH of 100 A.7.The JEDEC registration for the 6N137 specifes a maximum ICCH of 15 mA. Avago guarantees a maximum ICCHof 10 mA.8.The JEDEC registration for the 6N137 specifes a maximum ICCL of 18 mA. Avago guarantees a maximum ICCLof 13 mA.9.The JEDEC registration for the 6N137 specifes a maximum IEL of 2.0 mA. Avago guarantees a maximum IEL of -1.6 mA.10.The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the output pulse.11.The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the output pulse.12.tPSK is equal to the worst case diference in tPHL and/or tPLH that will be seen between units at any given temperature and specifed test conditions.13.See application section titled Propagation Delay, Pulse-Width Distortion and Propagation Delay Skewfor more information.14.The tELH enable propagation delay is measured from the 1.5 V point on the falling edge of the enable input pulse to the 1.5 V point on the rising edge of the output pulse.15.The tEHL enable propagation delay is measured from the 1.5 V point on the rising edge of the enable input pulse to the 1.5 V point on the falling edge of the output pulse.16.CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., VO > 2.0 V).17.CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., VO < 0.8 V).18.For sinusoidal voltages, (|dVCM | / dt)max = fCMVCM(p-p).19.Noexternalpullupisrequiredforahighlogicstateontheenableinput.Ifthe VEpinisnotused,tying VEto VCCwillresultinimprovedCMR performance. For single channel products only.20.Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.21.In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage 4500 Vrms for one second (leakage detection current limit, II-O 5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.22.In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 6000 V rms for one second (leakage detection current limit, II-O 5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.23.Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only.24.Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only141623451 2 3 4 5 6IF FORWARD INPUT CURRENT mA RL = 350 RL = 1 KRL = 4 K00VCC = 5 VTA = 25 CVO OUTPUT VOLTAGE V8-PIN DIP, SO-8VCC = 5.0 VVO = 0.6 V63-60 -20 20 60 100TA TEMPERATURE C280 40 0 -400ITH INPUT THRESHOLD CURRENT mARL = 350 145RL = 1 KRL = 4 K8-PIN DIP, SO-8IOH HIGH LEVEL OUTPUT CURRENT A-600TA TEMPERATURE C1001015-20520VCC = 5.5 VVO = 5.5 VVE = 2.0 V*IF = 250 A60 -40 0 40 80* FOR SINGLECHANNELPRODUCTSONLYVCC = 5.0 VVO = 0.6 V63-60 -20 20 60 100TA TEMPERATURE C280 40 0 -400ITH INPUT THRESHOLD CURRENT mARL = 350 145RL = 1 KRL = 4 KWIDEBODY1623451 2 3 4 5 6IF FORWARD INPUT CURRENT mA RL = 350 RL = 1 KRL = 4 K00VCC = 5 VTA = 25 CVO OUTPUT VOLTAGE VWIDEBODYFigure 2. Typical output voltage vs. forward input currentFigure 3. Typical input threshold current vs. temperatureFigure 1. Typical high level output current vs. temperature150.80.4-60 -20 20 60 100TA TEMPERATURE C0.280 40 0 -400VOL LOW LEVEL OUTPUT VOLTAGE VIO = 16 mA0.10.50.7IO = 6.4 mA8-PIN DIP, SO-8VCC = 5.5 VVE = 2.0 V*IF = 5.0 mA0.30.6IO = 12.8 mAIO = 9.6 mA* FOR SINGLECHANNELPRODUCTS ONLY0.80.4-60 -20 20 60 100TA TEMPERATURE C0.280 40 0 -400VOL LOW LEVEL OUTPUT VOLTAGE VIO = 16 mA0.10.50.7IO = 6.4 mAWIDEBODYVCC = 5.5 VVE = 2.0 VIF = 5.0 mA0.30.6IO = 12.8 mAIO = 9.6 mAVCC = 5.0 VVE = 2.0 V*VOL = 0.6 V7060-60 -20 20 60 100TA TEMPERATURE C5080 40 0 -4020IOL LOW LEVEL OUTPUT CURRENT mA40IF = 10-15 mAIF = 5.0 mA* FOR SINGLECHANNELPRODUCTS ONLYIF FORWARD CURRENT mA1.10.001VF FORWARD VOLTAGE V1.010001.30.011.5 1.2 1.40.1TA = 25 C101008-PIN DIP, SO-8IF+VF1.6IF - FORWARD CURRENT - mA1.20.001VF -FORWARD VOLTAGE -V1.010001.40.011.6 1.3 1.50.110100WIDEBODYIF+-VF1.7TA = 25 oCdVF/dT FORWARD VOLTAGE TEMPERATURE COEFFICIENT mV/C0.1 1 10 100IF PULSE INPUT CURRENT mA-1.9-2.2-2.1-2.0-1.8-2.3WIDEBODYdVF/dT FORWARD VOLTAGE TEMPERATURE COEFFICIENT mV/C0.1 1 10 100IF PULSE INPUT CURRENT mA-1.4-2.2-2.0-1.8-1.6-1.2-2.48-PIN DIP, SO-8Figure 7. Typical temperature coefcient of forward voltage vs. input currentFigure 4. Typical low level output voltage vs. temperature Figure 5. Typical low level output current vs. temperatureFigure 6. Typical input diode forward characteristic16OUTPUT VMONITORING NODEO+5 V75682341PULSE GEN.Z= 50 t = t = 5 nsO fIFLRRMCCV0.1FBYPASS*CLGNDINPUTMONITORINGNODErSINGLE CHANNELOUTPUT VMONITORING NODEO+5 V75682341PULSE GEN.Z= 50 t = t = 5 nsO fIFLRRMCCV0.1FBYPASSCL*GNDINPUTMONITORINGNODErDUAL CHANNEL1.5 VtPHL tPLHIFINPUTOVOUTPUTI= 7.50 mA FI= 3.75 mAF*CL IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE.VCC = 5.0 VTA = 25C105905 9 13IF PULSE INPUT CURRENT mA7515 11 730tP PROPAGATION DELAY ns6045tPLH , RL = 4 KtPLH , RL = 1 KtPLH , RL = 350 tPHL , RL = 350 1 K4 KVCC = 5.0 VIF = 7.5 mA10080-60 -20 20 60 100TA TEMPERATURE C6080 40 0 -400tP PROPAGATION DELAY ns4020tPLH , RL = 4 KtPLH , RL = 1 KtPLH , RL = 350 tPHL , RL = 350 1 K4 KVCC = 5.0 VIF = 7.5 mA4030-20 20 60 100TA -TEMPERATURE -oC2080 40 0 -40PWD - PULSE WIDTH DISTORTION - ns10RL = 350RL = 1 kRL = 4 k0-60-10tr, tf RISE, FALL TIME ns-600TA TEMPERATURE C100300-204020 60 -40 0 40 806029020VCC = 5.0 VIF = 7.5 mARL = 4 kRL = 1 kRL = 350 , 1 k, 4 ktRISEtFALLRL = 350 Figure 8. Test circuit for tPHL and tPLHFigure 9. Typical propagation delay vs. tem-peratureFigure 10. Typical propagation delay vs. pulse input currentFigure 11. Typical pulse width distortion vs. temperatureFigure 12. Typical rise and fall time vs. tempera-ture17OUTPUT VMONITORING NODEO1.5 VtEHL tELHVEINPUTOVOUTPUT3.0 V1.5 V+5 V75682341PULSE GEN.Z= 50 t = t = 5 nsO fIFLRCCV0.1 FBYPASS*CL*CIS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE.LGNDr7.5 mAINPUTVEMONITORING NODEtE ENABLE PROPAGATION DELAY ns-600TA TEMPERATURE C10090120-203020 60 -40 0 40 8060VCC = 5.0 VVEH = 3.0 VVEL = 0 VIF = 7.5 mAtELH, RL = 4 ktELH, RL = 1 ktEHL, RL = 350 , 1 k, 4 ktELH, RL = 350 +5 V75682341 CCV0.1 FBYPASSGNDOUTPUT VMONITORING NODEOPULSEGENERATORZ= 50 O+IFBAVFFCMVRLSINGLE CHANNEL+5 V75682341 CCV0.1 FBYPASSGNDOUTPUT VMONITORING NODEOPULSEGENERATORZ= 50 O+IFBAVFFCMVRLDUAL CHANNELVO0.5 VOV(MIN.)5 V0 VSWITCH AT A:I = 0 mAFSWITCH AT B:I = 7.5 mAFCM VHCMCMLOV(MAX.)CMV(PEAK)VOFigure 13. Test circuit for tEHL and tELHFigure 14. Typical enable propagation delay vs. temperatureFigure 15. Test circuit for common mode transient immunity and typical waveforms18OUTPUT POWER PS, INPUT CURRENT IS00TS CASE TEMPERATURE C200 50400125 25 75 100 150600800200100300500700PS (mW)IS (mA)HCPL-2611 OPTION 060175OUTPUT POWER PS, INPUT CURRENT IS00TS CASE TEMPERATURE C175 50400125 25 75 100 150600800200100300500700PS (mW)IS (mA)HCNWXXXXGND BUS (BACK)VCC BUS (FRONT)ENABLE0.1F10 mm MAX.(SEE NOTE 5)OUTPUTNCNCSINGLE CHANNELDEVICE ILLUSTRATED.Figure 16. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-5Figure 17. Recommended printed circuit board layout19Figure 18. Recommended TTL/LSTTL to TTL/LSTTL interface circuit*DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT.VCC15 VGND 1D1*IFVFSHIELDSINGLE CHANNEL DEVICE865390 0.1 FBYPASS23+5 VGND 2VCC22470 17VEVCC15 VGND 1D1*SHIELDDUAL CHANNEL DEVICECHANNEL 1 SHOWN875390 0.1 FBYPASS12+5 VGND 2VCC22470 1IFVF20Propagation Delay, Pulse-Width Distortion and Propagation Delay SkewPropagationdelayisafgureofmeritwhichdescribes howquicklyalogicsignalpropagatesthroughasys-tem. The propaga tion delay from low to high (tPLH) is the amount of time required for an input signal to propagate to the output, causing the output to change from low to high.Similarly,thepropagationdelayfromhightolow (tPHL) is the amount of time required for the input signal to propagate to the output causing the output to change from high to low (see Figure 8).Pulse-widthdistortion(PWD)resultswhentPLHandtPHL diferinvalue.PWDisdefnedasthediferencebe-tweentPLH andtPHLandoftendeterminesthemaximum dataratecapabil ityofatransmissionsystem.PWDcan beexpressedinpercentbydividingthePWD(inns)by the minimum pulse width (in ns) being transmitted. Typi-cally, PWD on the order of 20-30% of the minimum pulse width is tolerable; the exact fgure depends on the par-ticular application (RS232, RS422, T-l, etc.).Propagation delay skew, tPSK, is an important parameter to consider in parallel data appli ca tions where synchroniza-tionofsignalsonparalleldatalinesisaconcern.Ifthe paralleldataisbeingsentthroughagroupofoptocou-plers,difer encesinpropagationdelayswillcausethe data to arrive at the outputs of the optocouplers at difer-ent times. If this diference in propagation delays is large enough,itwilldeterminethemaximumrateatwhich parallel data can be sent through the optocouplers.Propagation delay skew is defned as the diference be-tween the minimum and maximum propagation delays, eithertPLHortPHL,foranygivengroupofoptocouplers which are operating under the same conditions (i.e., the same drive current, supply voltage, output load, and op-erating tempera ture). As illustrated in Figure 19, if the in-puts of a group of optocouplers are switched either ON orOFFatthesametime,tPSKisthediferencebetween the shortest propagation delay, either tPLH or tPHL, and the longest propagation delay, either tPLH or tPHL.Asmentionedearlier,tPSKcandeterminethemaximum paralleldatatransmissionrate.Figure20isthetiming diagramofatypicalparalleldataapplicationwithboth theclockandthedatalinesbeingsentthroughopto-couplers. The fgure shows data and clock signals at the inputsandoutputsoftheoptocouplers.Toobtainthe maximumdatatransmissionrate,bothedgesofthe clock signal are being used to clock the data; if only one edge were used, the clock signal would need to be twice as fast.Propagationdelayskewrepresentstheuncertaintyof whereanedgemightbeafterbeingsentthroughan opto coupler.Figure20showsthattherewillbeuncer-tainty in both the data and the clock lines. It is important thatthesetwoareasofuncertaintynotoverlap,other-wisetheclocksignalmightarrivebeforeallofthedata outputshavesettled,orsomeofthedataoutputsmay start to change before the clock signal has arrived. From these considera tions, the absolute minimum pulse width that can be sent through optocouplers in a parallel appli-cation is twice tPSK. A cautious design should use a slightly longer pulse width to ensure that any additional uncer-tainty in the rest of the circuit does not cause a problem.ThetPSKspecifedoptocouplersofertheadvantagesof guaranteed specifcations for propagation delays, pulse-widthdistortionandpropagationdelayskewoverthe recom mendedtemper a ture,inputcurrent,andpower supply ranges.Figure 19. Illustration of propagation delay skew - tPSKFigure 20. Parallel data transmission example50%1.5 VIFVO50% IFVOtPSK1.5 VDATAtPSKINPUTSCLOCKDATAOUTPUTSCLOCKtPSKFor product information and a complete list of distributors, please go to our website: www.avagotech.comAvago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.Data subject to change. Copyright 2005-2014 Avago Technologies. All rights reserved. Obsoletes AV02-0170EN AV02-0940EN-July 2, 2014