63063 002 stainless gradesQQS-763, AMS-QQS-763 PH 13-8 MO AMS-5629 Type 1, AMS-2300, Cap. of ASTM-A-564 Grade XM-13, STM-05-602 (Exc. Sonic some sizes check TR’s), HMS -6-1105 (Exc

STA

INLE

SS

STAINLESSGRADES STOCKED

[email protected] 1.800.423.6651

1FRY STEEL COMPANY

(562) 802-2721

304 L AMS-5647, ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763, ASME-SA-479, DMS 2050Rev A

304-L Plate Bar CHEMS ONLY TO FOLLOWING:ASTM-A & ASME-SA-240, ASTM-A &ASME-SA-276, ASTM-A-479, AMS-QQS & QQS 763, ASTM-A-484 Gauge& Width Table #5, ASTM-A-262Practice A or E, AMS-5647

304 L Prec.Grd Same Specs. as Reg. 304-L

304 L Cond. “B” QQS-763 CHEMS ONLY, AMS-QQS-(Hi Tensile) 763 CHEMS ONLY

304 L. V.M. AMS-5647, ASTM-A-276, ASTM-A-479,ASTM-A-484, ASTM-E-45 METHOD D(Exc. Transverse), QQS-763, AMS-QQS-763, ASME-SA-479, MBO-160-034 (Exc. Sonic), MBO-160-037 (Exc.Grain Size), DMS 2050 Rev A

303 Sul AMS-5640 Type 1, ASTM-A-582,ASTM-A-484, ASTM-A-320 Grd. B8FCL. 1, MIL-S-7720, MIL-W-52263(1⁄2" & under), QQS-763C, QQS-764B(over 1⁄2")

303 Sul Prec.Grd Same Specs. as Reg. 303

303 Sul Cond.“B” ASTM-A-320 Grd. B8F CL. 2, ASTM-A(Hi Tensile) 484, MIL-S-7720, MIL-W-52263 (1⁄2" &

under), QQS-764A (over 1⁄2")

303 Sel AMS-5640 Type 2, AMS-5641, ASTM-A-582, ASTM-A-484, ASTM-A-320Grd. B8F CL.1, MIL-S-7720, MIL-W-52263 (1⁄2" & under), QQS-763C, QQS-764B (over 1⁄2")

303 Sel Prec.Grd. Same Specs as Reg 303 Sel

303 Sel Cond. “B” AMS-5738, ASTM-A-320 Grd. B8F(Hi Tensile) CL.2, ASTM-A-484, MIL-S-7720, MIL-

W-52263 (1⁄2" & under), QQS-763C,QQS-764A (over 1⁄2")

309 AMS-5650, ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763

310 AMS-5651, ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763, ASME-SA-479

316 AMS-5648, AMS-S-7720, ASTM-A-276, ASTM-A-320 Grd. B8M CL.1,ASTM-A-193 Grd. B8M CL.1, ASTM-A-479, ASTM-A-484, MIL-S-7720, QQS-763, AMS-QQS-763, ASME-SA-479,

316 Prec.Grd Same Specs. as Reg. 316

316 Cond. “B” AMS-S-7720, ASTM-A-276, ASTM-A-(Hi Tensile) 193 Grd. B8M CL.2, ASTM-A-320 Grd.

B8M CL.2, ASTM-A-484, MIL-S-7720,QQS-763, AMS-QQS-763

PH 13-8 MO AMS-5629 Type 1, AMS-2300, Cap. ofASTM-A-564 Grade XM-13, STM-05-602 (Exc. Sonic some sizes checkTR’s), HMS -6-1105 (Exc. Sonic somesizes), STO-160-LBO-013, DMS 2100,Sonic per MIL-S-2154 CL.A (CheckTR’s)

15-5 PH “H1025” AMS-5659 Type 1, ASTM-A-564 TypeXM-12, AMS-2300, AMS-2315,ASTM-A-484, AMS-H6875

15-5 PH V.M. AMS-5659 Type 1, AMS-2300, AMS-2315, Cap. of ASTM-A-564 GradeXM-12, ASTM-A-484

15-5 PH ESR AMS-5659 Type 2, Cap. of ASTM-A-564 Grade XM-12, ASTM-A-484

17-4 PH AMS-5643, AMS-2303, ASTM-A-484,Cap. of ASTM-A-564 Grade 630, Cap.of ASME-SA-564 Type 630, Cap. ofMBO-160-003 (Exc. Hardness & Sonic)

17-4 PH “H-1150” AMS-5643 CHEMS ONLY, ASTM-A-564 Cond H-1150

17-4 PH NACE MR0175, AMS-2303, ASTM-A-Double “H-1150” 564 Type 630 Cond H1150D, RC33

Max, Chems only to AMS-5643 andASTM-A-370

17-4 PH Prec.Grd Same Specs. as Reg. 17-4

17-7 PH AMS-5644, Cap. of ASTM-A-564 Type631

302 AMS-S-7720, ASTM- A-276, ASTM-A-479, ASTM-A-484, MIL-S-7720, QQS-763,AMS-QQS-763, ASME-SA-479

302 Plate Bar CHEMS ONLY TO FOLLOWING:ASTM-A & ASME-SA-240, ASTM-A &ASME-SA-276, ASTM-A-479, AMS-QQS & QQS 763, ASTM-A-484 Gauge& Width Table #5, ASTM-A-262Practice A or E


302 Cond. “B” AMS-5637 CHEMS ONLY, AMS-S (Hi Tensile) 7720, ASTM-A-276, ASTM-A-484,

MIL-S-7720, QQS 763, AMS-QQS-763

304 AMS-5639, ASTM-A-484, ASTM-A-276,ASTM-A-479, ASTM-A-193 Grd. B8 CL.1,ASTM-A-320 Grd. B8 CL.1, ASME-SA-479, QQS-763, AMS-QQS-763

304 Plate Bar CHEMS ONLY TO FOLLOWING:ASTM-A & ASME-SA-240, ASTM-A &ASME-SA-276, ASTM-A-479, AMS-QQS & QQS 763, ASTM-A-484 Gauge& Width Table #5, ASTM-A-262Practice A or E, AMS-5639


304 Cond. “B” ASTM-A-484, ASTM-A-276, ASTM-A-(Hi Tensile) 193 Grd. B8 CL. 2, QQS-763, AMS-

QQS-763

SPECIFICATIONSSPECIFICATIONS

PH - Precipitation Hardenable VM - Vacuum Arc Re-melt ESR - Electroslag Re-melt Prec. Grd - Precision Ground tol. +/- .0005Plate-Bar - Commercial Grade product. The flat bar is cut from plate and then run through a “Gaured” machine for final processing.

Chems Only - Certifiable to Chemistry only - No physicals Sel - Selenium L - Low Carbon Sul - Sulfer Sol trt - Solution treated

STAINLESSGRADES STOCKED

2FRY STEEL COMPANY1.800.423.6651

[email protected]

(562) 802-2721

316 L AMS-5653, ASTM-A-276, ASTM-A-479, ASTM-A-484, ASME-SA-479,QQS-763, AMS-QQS-763

316 L Prec.Grd Same Specs. as Reg. 316-L

316 L Cond. “B” QQS-763 CHEMS ONLY and AMS-QQS-(Hi Tensile) 763 CHEMS ONLY

316/316-L Vac. Melt. Same Specs as Reg 316/316-L,ASTM-E-45 METHOD D

317 ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763

317 L ASTM-A-484

321/321H AMS-5645, ASTM-A-276, ASTM-A-479, ASTM-A-484, ASTM-A-193 Grd.B8T CL.1, ASTM-A-320 Grd. B8TCL.1, QQS-763, AMS-QQS-763, ASME-SA-479

330 AMS-5716

347/347H AMS-5646, ASTM-A-276, ASTM-A-479, ASTM-A-484, ASME-SA-479,ASTM-A-193-Grd. B8C CL.1, ASTM-A-320 Grd. B8C CL.1, QQS-763, AMS-QQS-763

AM-355 AMS-5743, Cap. of AMS-5744, Cap.of ASTM-A-564 Type 634, ASTM-A-484, EMS-55443, Honeywell 91547-M3170 CHEMS ONLY

403 AMS-2303, ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763, ASME-SA-479

410 AMS-5613, AMS-5612, AMS-2303,ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763, ASME-SA-479

416 AMS-5610 T-2, ASTM-A-582, ASTM-A-484, MIL-W-52263 (1⁄2" & under),QQS-763C, QQS-764B (over 1⁄2")

416 Prec.Grd AMS-5610 T-2, ASTM-A-582, MIL-W-52263, QQS-763C

416 HT R.C. 26/32 ASTM-A-582 COND. T, ASTM-A-484,MIL-W-52263 (1⁄2" & under), QQS-763CCOND H, QQS-764B COND. T (over 1⁄2"),EMS-537

418 (GREEK ASCOLOY) AMS-5616

420 AMS-5621, ASTM-A-276, ASTM-A-484, QQS-763, AMS-QQS-763

420 F AMS-5620 Type 2, ASTM-A-582,ASTM-A-484

SPECIFICATIONS

Refer to pages 57 through 68 for tolerances, weights, recommended stock removal, chemical analysis, machinability.General information in back of book.

SPECIFICATIONS

NOTE: AUTOMATIC EXCEPTIONS TO THE SPEC LISTED ARE: LINE MARKING AND INSPECTION (I.E. MAG., SONIC, ETC.)

1 Trademark Armco 3 Trademark Carpenter Technology

422 ASTM-A-565 GRADE 616, Cap. of AMS5655, Cap. of 10705BU, Cap. ofB50A125, Cap. of B50A951A1, DOD-F24669/7

430 AMS-5627, ASTM-A-276, ASTM-A-479, ASTM-A-484, QQS-763, AMS-QQS-763

430 F ASTM-A-582, ASTM-A-484, MIL-W-52263 (1⁄2" & under), QQS-763CCHEMS ONLY, QQS-764B (over 1⁄2")

431 AMS-5628, AMS-S-18732, AMS-2303,ASTM-A-276, ASTM-A-484, MIL-S-18732, QQS-763 (EXC. HARDNESS &IZOD TESTS), HI SHEAR #115 CHEMSONLY, DMS-1565 (EXC. Sonic)

440 A AMS-5631, ASTM-A-276, ASTM-A-484, QQS-763, AMS-QQS-763

440 C AMS-5630, ASTM-A-276, ASTM-A-484, QQS-763, AMS-QQS-763

440 C Prec.Grd Same specs as Reg. 440 C

440 C VAC. MELT AMS-5630, AMS-5880 BEARINGQUALITY, AMS 5618, ASTM-A-276,QQS-763, AMS-QQS-763, BEMS-25003E, RBO-160-064 (Exc. Sonic)

440 F Se AMS-5632 Type 2, ASTM-A-582, ASTM-A-484, QQS-764B (over 1⁄2")

446 ASTM-A-276, QQS-763, AMS-QQS-763

455 Sol. Tr. (12-9-2) AMS-5617 (Under 3" Grd. 1, 3" & overGrd. 2), MIL-S-83311, Cap. of ASTM-A-564 GRD. XM-16, HMS-6-1093GExc. Para. 3.2.1.1

465 Sol. Tr. AMS 59361NITRONIC 40 (21-6-9) AMS-5656, ASTM-A-276

1NITRONIC 50 (22-13-5) AMS-5764, ASTM-A-479 XM-19, ASTM-

A-276, ASTM-A-193 Grd. B8R CL.1,ASME-SA-479 XM-19

1NITRONIC 60 AMS 5848, ASTM-A-479, ASTM-A-276

(S21800), ASTM-A-193 Grd. B8S,ASTM-A-194, ASME-SA-479, ASME-SA-193 Grd. B8S, ASME-SA-194

FRY ALLOY 20 ASTM-B-473

.130" 302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.303 Sel C.F. Ann.316 C.F. Ann.316 L C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.

.135" 440 C C.F. Ann.

9/64" 17-4 PH C.G. Sol trt303 S C.F. Ann.416 C.F. Ann.

5/32" 17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S P.G. Ann.303 S C.F. Ann.303 Sel C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.


3/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH P.G. Sol trt302 P.G. Ann.304 P.G. Ann.304 L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”303 Sel P.G. Ann.316 P.G. Ann.316 L P.G. Ann.316 C.F. Ann.316 L C.F. Ann.321 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.

1/16" 302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.416 C.F. Ann.

5/64" 303 S C.F. Ann.416 C.F. Ann.

3/32" 17-4 PH C.G. Sol trt302 C.F. Ann.302 P.G. Ann.304 C.F. Ann.304 P.G. Ann.304 L C.F. Ann.304 L P.G. Ann.303 P.G. Ann.303 S C.F. Ann.303 Sel C.F. Ann.416 C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.


1/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH P.G. Sol trt302 P.G. Ann.304 P.G. Ann.304 L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens. C.F. “B”304 Hi tens. C.F. “B”304 L C.F. Ann.304 Hi tens. C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 Sel P.G. Ann.303 Sel C.F. Ann.303 Sel Hi tens. C.F. “B”316 C.F. Ann.316 L C.F. Ann.321 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 F C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 F Se C.G. Ann.

.130" 17-4 PH C.G. Sol trt


3FRY STEEL COMPANY

(562) 802-2721

SIZE TYPE FINISH COND. SIZE TYPE FINISH COND.

STAINLESSROUNDSSTOCKED IN 12' R/L

Finish: C.D. – Cold Drawn Condition: Ann. – Annealed ESR – Electroslag Re-melt V.M. – Vacuum Arc Re-meltC.F. – Cold Finish A&P – Annealed & Pickled Sel – Selenium P.G. – Precision GroundH.R. – Hot Rolled H.T. – Heat treated (RC 26/32) “B” – Hi Tensile L – Low CarbonC.G. – Centerless Ground Sol trt – Solution Treated S – Sulfer


3/16" 416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 F Se C.G. Ann.

.1925" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.303 Sel C.F. Ann.316 C.F. Ann.316 L C.F. Ann.321 C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.

.1975" 440 C C.F. Ann.

13/64" 17-4 PH C.G. Sol trt303 S C.F. Ann.416 C.F. Ann.440 C C.F. Ann.

7/32" 17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.

15/64" 17-4 PH C.G. Sol trt303 S C.F. Ann.416 C.F. Ann.440 C C.F. Ann.

1/4" 13-8 MO V.M. C.G. Sol trt15-5 PH M.V. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 P.G. Ann.304 P.G. Ann.


[email protected]

(562) 802-2721

NOTE: IT IS NOT ADVISABLE TO TRY TO FINISH ON SIZE FROM THE SIZE PURCHASED.NOTE: BARS ARE NOT PERFECTLY ROUND, SQUARE, OR STRAIGHT.

PLEASE REFER TO THE VARIOUS CHARTS IN THIS BOOK.


1/4" 304 L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”303 Sel P.G. Ann.310 C.F. Ann.316 P.G. Ann.316 L P.G. Ann.316 C.F. Ann.316 Hi tens C.F. “B”316 VM C.G. Ann.316 L C.F. Ann.316 L Hi tens C.F. “B”316 V.M. C.G. Ann.317 C.F. Ann.317 L C.F. Ann.321 C.F. Ann.330 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.420 F C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.255" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L Hi tens C.F. “B”303 S C.F. Ann.



5FRY STEEL COMPANY

(562) 802-2721


5/16" 303 Sel P.G. Ann.310 C.F. Ann.316 P.G. Ann.316-L P.G. Ann.316 C.F. Ann.316 Hi tens C.F. “B”316 L C.F. Ann.316 L Hi tens C.F. “B”317 C.F. Ann.317 L C.F. Ann.321 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.420F C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.3175" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F “B”304 L C.F. Ann.304 L Hi tens C.F. “B”303 S C.F. Ann.303 Sel C.F. Ann.316 C.F. Ann.316 L C.F. Ann.321 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.430 F C.F. Ann.

.3225" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt431 C.F. Ann.440 C C.F. Ann.455 C.G. Ann.

21/64" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt

.255" 303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”316 C.F. Ann.316 L C.F. Ann.321 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.430 F C.F. Ann.

.260" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt440 C C.F. Ann.455 C.G. Ann.

.265" 431 C.F. Ann.

17/64" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt303 S C.F. Ann.440 C C.F. Ann.

9/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S. P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.

19/64" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt303 S C.F. Ann.

5/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”




[email protected]

(562) 802-2721




3/8" 410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.420 F C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.380" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”303 S C.F. Ann.303 Sel C.F. Ann.304 L C.F. Ann.304 L Hi tens C.F. “B”316 C.F. Ann.316 L C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 F C.F. Ann.

.385" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt431 C.F. Ann.440 C C.F. Ann.455 C.G. Ann.


13/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.

21/64" 303 S C.F. Ann.416 C.F. Ann.440 C C.F. Ann.

11/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.


3/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”303 Sel P.G. Ann.310 C.F. Ann.316 P.G. Ann.316 L P.G. Ann.316 C.F. Ann.316 Hi tens C.F. “B”316 V.M. C.G. Ann.316 L C.F. Ann.316 L Hi tens C.F. “B”316 L V.M. C.G. Ann.317 C.F. Ann.317 L C.F. Ann.321 C.F. Ann.330 C.F. Ann.347 C.F. Ann.403 C.F. Ann.



7FRY STEEL COMPANY

(562) 802-2721


7/16" Fry Alloy 20 C.G. Ann.

.4425" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L Hi tens C.F. “B”303 S C.F. Ann.303 Sel C.F. Ann.316 C.F. Ann.316 L C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 F C.F. Ann.440 C C.F. Ann.

.4475" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt431 C.F. Ann.440 C C.F. Ann.455 C.G. Ann.


15/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.F. Ann.304 C.F. Ann.304 L C.F. Ann.303 S C.F. Ann.303 Sel C.F. Ann.416 HT RC 26/32 C.G. H.T.420 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.


1/2" 13-8 MO V.M. C.G. Sol trt15-5 PH C.G. “H1025”15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.302 C.F. Ann.304 C.F. Ann.

13/32" 430 C.F. Ann.430 F C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 F Se C.G. Ann.


7/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.302 C.F. Ann.304 C.F. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”303 Sel P.G. Ann.316 P.G. Ann.316-L P.G. Ann.316 C.F. Ann.316 Hi tens C.F. “B”316 L C.F. Ann.316 L Hi tens C.F. “B”317 C.F. Ann.317 L C.F. Ann.321 C.F. Ann.330 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.G. Ann.440 C C.F. Ann.440 C P.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.




[email protected]

(562) 802-2721




.505" 316 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 F C.G. Ann.440 C C.G. Ann.

.510" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt431 C.G. Ann.455 C.G. Ann.

33/64" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt303 S C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

17/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440F Se C.G. Ann.

9/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”302 P.G. Ann.304 P.G. Ann.304 L P.G. Ann.304 L C.G. Ann.304 L Hi tens C.G. “B”303 S P.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”303 Sel P.G. Ann.310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.

1/2" 302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.F. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.F. “B”303 S P.G. Ann.303 S C.F. Ann.303 S Hi tens C.F. “B”303 Sel C.F. Ann.303 Sel Hi tens C.F. “B”303 Sel P.G. Ann.309 C.F. Ann.310 C.F. Ann.316 P.G. Ann.316-L P.G. Ann.316 C.F. Ann.316 Hi tens C.F. “B”316 V.M. C.G. Ann.316 L C.F. Ann.316 L Hi tens C.F. “B”316 L V.M. C.G. Ann.317 C.F. Ann.317 L C.F. Ann.321 C.F. Ann.330 C.F. Ann.347 C.F. Ann.403 C.F. Ann.410 C.F. Ann.416 C.F. Ann.416 P.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.F. Ann.420 F C.F. Ann.422 C.F. Ann.430 C.F. Ann.430 F C.F. Ann.431 C.F. Ann.440 A C.F. Ann.440 C C.F. Ann.440 C P.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.502" 420 C.G. Ann.

.505" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.



9FRY STEEL COMPANY

(562) 802-2721


5/8" 304-L P.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”303 Sel P.G. Ann.309 C.G. Ann.310 C.G. Ann.316 P.G. Ann.316 L P.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C P.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.630" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 C.G. Ann.316 L C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.430 F C.G. Ann.

9/16" 317 L C.G. Ann.317 C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.Nitronic 40 C.G. Ann.Fry Alloy 20 C.G. Ann.

.5675" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.416 HT RC 26/32 C.G. H.T.440 C C.G. Ann.

.5725" 13-8 MO V.M. C.G. Sol trt431 C.G. Ann.

19/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.430 C.G. Ann.430 F C.G. Ann.440 C C.G. Ann.

5/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”302 P.G. Ann.304 P.G. Ann.




[email protected]

(562) 802-2721




.6925" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt

23/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.416 C.G. Ann.430 F C.G. Ann.440 C C.G. Ann.

3/4" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”303 Sel P.G. Ann.309 C.G. Ann.310 C.G. Ann.316 P.G. Ann.316 L P.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.330 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.

.630" 440 C C.G. Ann.

.635" 13-8 MO V.M . C.G. Sol trt15-5 PH V.M. C.G. Sol trt431 C.G. Ann.455 C.G. Ann.

41/64" 13-8 MO V.M. C.G. Sol trt

21/32" 13-8 MO V.M . C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.430 F C.G. Ann.440 C C.G. Ann.

11/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17- 4 PH C.G. Sol trt17-4 PH C.G. “H1150”302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 C.G. Ann.316 Hi tens C.G. “B”316 L C.G. Ann.316 L Hi tens C.G. “B”317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.

.6925" 13-8 MO V.M. C.G. Sol trt



11FRY STEEL COMPANY

(562) 802-2721


13/16" 303 Sel Hi tens C.G. “B”316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.

.8175" 13-8 MO V.M. C.G. Sol trt440 C C.G. Ann.

27/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

7/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”309 C.G. Ann.

3/4" 431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.465 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.755" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.321 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.430 F C.G. Ann.440 C C.G. Ann.

.760" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt431 C.G. Ann.455 C.G. Ann.

.765" 17-4 PH C.G. Sol trt

49/64" 13-8 MO V.M. C.G. Sol trt

25/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.416 C.G. Ann.430 F C.G. Ann.440 C C.G. Ann.

13/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.




[email protected]

(562) 802-2721




15/16" 302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 C.G. Ann.316 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.Nitronic 40 C.G. Ann.

31/32" 17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

1" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH C.G. Double

“H1150”17-4 PH P.G. Sol trt17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”302 P.G. Ann.304 P.G. Ann.304-L P.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”303 Sel P.G. Ann.309 C.G. Ann.310 C.G. Ann.316 P.G. Ann.

7/8" 310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

.880" 17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

.885" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt

29/32" 13-8 MO V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304-L C.G. Ann.303 S C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

15/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt17-4 PH C.G. Sol trt17-4 C.G. “H1150”302 C.G. Ann.304 C.G. Ann.



13FRY STEEL COMPANY

(562) 802-2721


1-1/16" 304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 L C.G. Ann.316 L Hi tens C.G. “B”321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.446 C.G. Ann.

1-1/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.

1" 316 L P.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.330 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.465 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.005" 15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.430 F C.G. Ann.440 C C.G. Ann.

1.010" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt

1.015" 416 HT RC 26/32 C.G. H.T.

1-1/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”




[email protected]

(562) 802-2721




1-1/4" 303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”309 C.G. Ann.310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.330 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.465 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.260" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L Hi tens C.G. “B”

1.265" 17-4 PH C.G. Sol trt

1-5/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 C.G. Ann.316 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.

1-1/8" 422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.135" 13-8 MO V.M. C.G. Sol trt

1-3/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 C.G. Ann.316 Hi tens C.G. “B”316 L C.G. Ann.316 L Hi tens C.G. “B”321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.

1-1/4" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH C.G. Double

“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 S P.G. Ann.



15FRY STEEL COMPANY

(562) 802-2721


1-7/16" 302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 C.G. Ann.431 C.G. Ann.440 C C.G. Ann.


“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”309 C.G. Ann.310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.330 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.

1-5/16" 416 HT RC 26/32 C.G. H.T.420 C.G. Ann.430 C.G. Ann.430-F C.G. Ann.431 C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.Nitronic 40 C.G. Ann.

1-3/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”AM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.302 Hi tens C.G. “B”304 Hi tens C.G. “B”304 L C.G. Ann.304 L V.M. C.G. Ann.304 L Hi tens C.G. “B”303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”310 C.G. Ann.316 C.G. Ann.316 Hi tens C.G. “B”316 V.M. C.G. Ann.316 L C.G. Ann.316 L Hi tens C.G. “B”316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.385" 13-8 MO V.M. C.G. Sol trt

1-7/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt




[email protected]

(562) 802-2721




1-5/8" 416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 C C.G. Ann.440 F Se C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.

1-11/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.440 C C.G. Ann.


“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”309 C.G. Ann.310 C.G. Ann.316 C.G. Ann.316 V.M. C.G. Ann.316 L C.G. Ann.316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.418 (Greek Ascoloy) C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.

1-1/2" 430 F C.G. Ann.431 C.G. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.465 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.510" 13-8 MO V.M. C.G. Sol trt

1.515" 17-4 PH C.G. Sol trt

1-9/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.321 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.420 C.G. Ann.440 C C.G. Ann.


“H1150”AM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”310 C.G. Ann.316 C.G. Ann.316 V.M. C.G. Ann.316 L C.G. Ann.316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.



17FRY STEEL COMPANY

(562) 802-2721


1-7/8" 440 C C.G. Ann.440 F Se C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 60 C.G. Ann.

1-15/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.316 C.G. Ann.316 L C.G. Ann.347 C.G. Ann.416 C.G. Ann.440 C C.G. Ann.

2" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt15-5 PH ESR C.G. Sol trt15-5 PH C.G. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH C.G. Double

“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 S Hi tens C.G. “B”303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”309 C.G. Ann.310 C.G. Ann.316 C.G. Ann.316 V.M. C.G. Ann.316 L C.G. Ann.316 L V.M. C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 A C.G. Ann.440 C C.G. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.

1-3/4" 420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 A C.G. Ann.440 C C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.465 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

1.760" 15-5 PH V.M. C.G. Sol trt

1-13/16" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. C.G. Sol trt17-4 PH C.G. Sol trt302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 C.G. Ann.316 L C.G. Ann.347 C.G. Ann.416 C.G. Ann.440 C C.G. Ann.


“H1150”AM 355 C.G. Ann.302 C.G. Ann.304 C.G. Ann.304 L C.G. Ann.304-L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.310 C.G. Ann.316 C.G. Ann.316 L C.G. Ann.317 C.G. Ann.317 L C.G. Ann.321 C.G. Ann.347 C.G. Ann.403 C.G. Ann.410 C.G. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.




[email protected]

(562) 802-2721




2-1/4" 302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.310 R.T. Ann.316 R.T. Ann.316 V.M. C.G. Ann.316 L R.T. Ann.316 L V.M. C.G. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 C R.T. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 C.G. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

2-5/16" 17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.416 C.G. Ann.

2-3/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.

2" 455 C.G. Ann.465 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

2.010" 15-5 PH V.M. C.G. Sol trt

2-1/16" 15-5 PH V.M. R.T. Sol trt17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.

2-1/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.303 Sel C.G. Ann.303 Sel Hi tens C.G. “B”316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.431 R.T. Ann.440 C R.T. Ann.455 C.G. Ann.

2-3/16" 15-5 PH V.M. R.T. Sol trt17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.316 R.T. Ann.316 L R.T. Ann.416 C.G. Ann.

2-1/4" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH C.G. Double

“H1150”AM 355 C.G. Ann.



19FRY STEEL COMPANY

(562) 802-2721


2-9/16" 17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.

2-5/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T,420 C.G. Ann.440 C R.T. Ann.455 C.G. Ann.

2-11/16" 17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.416 C.G. Ann.


“H1150”AM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.

2-3/8" 420 C.G. Ann.431 R.T. Ann.440 C R.T. Ann.440 F Se C.G. Ann.455 C.G. Ann.

2-7/16" 17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.316 R.T. Ann.316 L R.T. Ann.416 C.G. Ann.


“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.309 R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 V.M. C.G. Ann.316 L R.T. Ann.316 L V.M. C.G. Ann.317 R.T. Ann. 317 L R.T. Ann. 321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 A R.T. Ann.440 C R.T. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 R.T. Ann.455 C.G. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.




[email protected]

(562) 802-2721




3" 347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 C.G. Ann.420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 A R.T. Ann.440 C R.T. Ann.440 C V.M. C.G. Ann.440 F Se C.G. Ann.446 R.T. Ann.455 R.T. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 C.G. Ann.

3-1/8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.440 C R.T. Ann.

3-1/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt17-4 PH C.G. Double

“H1150”AM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.416 HT RC 26/32 C.G. H.T.

2-3/4" 420 F C.G. Ann.422 C.G. Ann.430 C.G. Ann.430 F C.G. Ann.431 R.T. Ann.440 C R.T. Ann.440 F Se C.G. Ann.455 C.G. Ann.Nitronic 60 C.G. Ann.

2-13/16" 302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.

2-7/8" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S C.G. Ann.303 Sel C.G. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 C.G. Ann.420 C.G. Ann.420 F C.G. Ann.440 C R.T. Ann.

2-15/16" 17-4 PH C.G. Sol trt303 S C.G. Ann.

3" 13-8 MO V.M. C.G. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH C.G. Sol trt17-4 PH C.G. “H1150”17-4 PH C.G. Double

“H1150”17-7 PH C.G. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. C.G. Ann.303 S C.G. Ann.303 Sel C.G. Ann.309 R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 V.M. R.T. Ann.316 L R.T. Ann.316-L V.M. R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.



21FRY STEEL COMPANY

(562) 802-2721


3-1/2" 440 A R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.446 R.T. Ann.455 R.T. Ann.Nitronic 40 C.G. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 R.T. Ann.

3-5/8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

3-3/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt17-4 PH C.G. Double

“H1150”17-7 PH R.T. Sol trtAM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 R.T. Ann.420 F R.T. Ann.431 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Nitronic 60 R.T. Ann.

3-7/8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.

3-1/4" 418 (Greek Ascoloy) C.G. Ann.420 R.T. Ann.420 F R.T. Ann.431 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Nitronic 50 C.G. Ann.Nitronic 60 C.G. Ann.Fry Alloy 20 R.T. Ann.

3-3/8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.440 C R.T. Ann.

3-1/2" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt17-4 PH C.G. “H1150”17-7 PH R.T. Sol trtAM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 V.M. R.T. Ann.316 L R.T. Ann.316 L V.M. R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 R.T. Ann.420 F R.T. Ann.422 R.T. Ann.430 R.T. Ann.430 F C.G. Ann.431 R.T. Ann.




[email protected]

(562) 802-2721




4-1/8" 321 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

4-1/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt 17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.430 F R.T. Ann.431 R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.455 R.T. Ann.Fry Alloy 20 R.T. Ann.

4-3/8" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.321 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

4-1/2" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt17-4 PH R.T. “H1150”17-4 PH R.T. Double

“H1150”AM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.310 R.T. Ann.316 R.T. Ann.

3-7/8" 304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.403 R.T. Ann.410 R.T. Ann.440 C R.T. Ann.

4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt15-5 PH R.T. “H1025”17-4 PH R.T. Sol trt17-4 PH R.T. “H1150”17-4 PH C.G. Double

“H1150”17-7 PH R.T. Sol trtAM 355 C.G. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 V.M. R.T. Ann.316 L R.T. Ann.316 L V.M. R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.416 HT RC 26/32 C.G. H.T.418 (Greek Ascoloy) C.G. Ann.420 R.T. Ann.420 F R.T. Ann.422 R.T. Ann.430 R.T. Ann.430 F C.G. Ann.431 R.T. Ann.440 A R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.446 R.T. Ann.455 R.T. Ann.Nitronic 40 R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry Alloy 20 R.T. Ann.

4-1/8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.



23FRY STEEL COMPANY

(562) 802-2721


5" 17-4 PH R.T. Double “H1150”

AM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.420 F R.T. Ann.422 R.T. Ann.430 R.T. Ann.430 F R.T. Ann.431 R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.446 R.T. Ann.455 R.T. Ann.Nitronic 40 R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry Alloy 20 R.T. Ann.

5-1/8" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.

5-1/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

5-1/2" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.

4-1/2" 316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.420 F R.T. Ann.422 R.T. Ann.430 R.T. Ann.430 F R.T. Ann.431 R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.446 R.T. Ann.455 R.T. Ann.Nitronic 40 R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry Alloy 20 R.T. Ann.

4-5/8" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.

4-3/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.431 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.

4-7/8" 15-5 PH V.M. R.T. Sol trt

5" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. “H1150”17-7 PH R.T. Sol trt




[email protected]

(562) 802-2721




6" 416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.420 F R.T. Ann.422 R.T. Ann.430 R.T. Ann.431 R.T. Ann.440 C R.T. Ann.440 C V.M. R.T. Ann.455 R.T. Ann.Nitronic 40 R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry Alloy 20 R.T. Ann.

6-1/8" 17-4 PH R.T. Sol trt

6-1/4" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

6-1/2" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.431 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Fry Alloy 20 R.T. Ann.

6-3/4" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.

5-1/2" 304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.420 F R.T. Ann.430 R.T. Ann.431 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Fry Alloy 20 R.T. Ann.

5-5/8" 17-4 PH R.T. Sol trt

5-3/4" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

6" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. “H1150”17-4 PH R.T. Double

“H1150”17-7 PH R.T. Sol trtAM 355 R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.304 L V.M. R.T. Ann.303 S R.T. Ann.303 Sel R.T. Ann.310 R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.



25FRY STEEL COMPANY

(562) 802-2721


7-1/2" Fry Alloy 20 R.T. Ann.

7-3/4" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.

8" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Nitronic 40 R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry Alloy 20 R.T. Ann.

8-1/4" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.416 R.T. Ann.

8-1/2" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann. 403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.

6-3/4" 316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

7" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.418 (Greek Ascoloy) R.T. Ann.420 R.T. Ann.440 C R.T. Ann.455 R.T. Ann.Fry Alloy 20 R.T. Ann.

7-1/4" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

7-1/2" 15-5 PH V.M. R.T. Sol trt15-5 PH ESR R.T. Sol trt17-4 PH R.T. Sol trt17-4 PH R.T. Double

“H1150”302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.440 C R.T. Ann.




[email protected]

(562) 802-2721




10-1/2" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.

11" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt303 S R.T. Ann.302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.316 R.T. Ann.316 L R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

11-1/2" 17-4 PH R.T. Sol trt403 R.T. Ann.410 R.T. Ann.

12" 13-8 MO V.M. R.T. Sol trt 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

12-1/2" 17-4 PH R.T. Sol trt403 R.T. Ann.410 R.T. Ann.

13" 13-8 MO V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

8-1/2" 440 C R.T. Ann.

8-3/4" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.

9" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.440 C R.T. Ann.

9-1/2" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

10" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann. 316 L R.T. Ann.317 R.T. Ann.317 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.420 R.T. Ann.440 C R.T. Ann.Nitronic 50 R.T. Ann.Nitronic 60 R.T. Ann.Fry AIIoy 20 R.T. Ann.



27FRY STEEL COMPANY

(562) 802-2721


13-1/2" 17-4 PH R.T. Sol trt

14" 13-8 MO V.M. R.T. Sol trt15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

15" 15-5 PH V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 R.T. Ann.316 R.T. Ann.316 L R.T. Ann.321 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

16“ 13-8 MO V.M. R.T. Sol trt17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304 L R.T. Ann.303 S R.T. Ann.316 R.T. Ann.316-L R.T. Ann.321 R.T. Ann.347 R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.440 C R.T. Ann.

17" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304-L R.T. Ann.303 R.T. Ann.316 R.T. Ann.316-L R.T. Ann.

18" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304-L R.T. Ann.303 R.T. Ann.316 R.T. Ann.316-L R.T. Ann.403 R.T. Ann.410 R.T. Ann.

18" 416 R.T. Ann.

19" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304-L R.T. Ann.316 R.T. Ann.316-L R.T. Ann.

20" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304L R.T. Ann.303 R.T. Ann.316 R.T. Ann.316L R.T. Ann.403 R.T. Ann.410 R.T. Ann.416 R.T. Ann.

22" 17-4 PH R.T. Sol trt302 R.T. Ann.304 R.T. Ann.304-L R.T. Ann.303 R.T. Ann.

23" 17-4 PH R.T. Sol trt

24" 17-4 PH R.T. Sol trt


STAINLESSHEXAGONS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


3/8" 316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.430-F C.D. Ann.

13/32" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.

7/16" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.430 F C.D. Ann.


1/2" 13-8 MO V.M C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.420 C.D. Ann.430 F C.D. Ann.

1/8" 303 S C.D. Ann.303 Sel C.D. Ann.416 C.D. Ann.

5/32" 303 S C.D. Ann.

3/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.416 C.D. Ann.

7/32" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.

15/64" 440 C C.F. Ann.

1/4" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.416 C.D. Ann.430-F C.D. Ann.


5/16" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.416 C.D. Ann.420 C.D. Ann.430 F C.D. Ann.


3/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”



STAINLESSHEXAGONS

STOCKED IN 12' R/L


29FRY STEEL COMPANY

(562) 802-2721


21/32" 304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.

11/16" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

3/4" 13-8 MO V.M. C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.420 C.D. Ann.430 F C.D. Ann.440 C C.D. Ann.

13/16" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.416 C.D. Ann.

7/8" 13-8 MO V.M. C.F. Sol trt

1/2" 440 C C.D. Ann.


9/16" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.420 C.D. Ann.


5/8" 13-8 MO V.M. C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.420 C.D. Ann.430 F C.D. Ann.440 C C.D. Ann.

21/32" 17-4 PH C.F. Sol trt302 C.D. Ann.


STAINLESSHEXAGONS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


1-1/16" 304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1-1/8" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.

1-3/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.416 C.D. Ann.

1-1/4" 13-8 MO V.M. C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.D. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.440 C H.R. Ann.

1-5/16" 302 C.D. Ann.304 C.D. Ann.

7/8" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.

15/16" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1" 13-8 MO V.M. C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 Hi tens C.F. “B”304 Hi tens C.F. “B”304 L C.D. Ann.304 L Hi tens C.F. “B”303 S C.D. Ann.303 Sel C.D. Ann.303 Sel Hi tens C.F. “B”316 C.D. Ann.316 Hi tens C.F. “B”316 L C.D. Ann.316 L Hi tens C.F. “B”321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.416 HT RC 26/32 C.F. H.T.440 C C.D. Ann.

1-1/16" 17-4 PH C.F. Sol trt302 C.D. Ann.



STAINLESSHEXAGONS

STOCKED IN 12' R/L


31FRY STEEL COMPANY

(562) 802-2721


1-7/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.416 C.D. Ann.

2" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

2-1/8" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.416 C.D. Ann.




2-5/8" 303 S C.D. Ann.


1-5/16" 304 L C.D. Ann.303 S C.D. Ann.416 C.D. Ann.

1-3/8" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1-7/16" 303 S C.D. Ann.

1-1/2" 13-8 MO V.M. C.F. Sol trt15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1-9/16" 303 S C.D. Ann.321 C.D. Ann.

1-5/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1-3/4" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.


STAINLESSHEXAGONS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721




3" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.

STAINLESSSQUARESSTOCKED IN 12' R/L


33FRY STEEL COMPANY

(562) 802-2721


1/2" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.440 C H.R. A&P

9/16" 17-4PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.416 C.D. Ann.

5/8" 15-5 PH V.M. C.F. Sol trt17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.440 C H.R. A&P

11/16" 303 S C.D. Ann.

3/4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. C.F. Sol trt17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.440 C H.R. A&P

13/16" 316 C.D. Ann.316 L C.D. Ann.

7/8" 17-4 PH H.R. A&P

1/8" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.

3/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.416 C.D. Ann.

1/4" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

5/16" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

3/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.

7/16" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.416 C.D. Ann.

1/2" 13-8 MO-V.M. H.R. A&P




[email protected]

(562) 802-2721




1-1/4" 316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.440 C H.R. A&PNitronic 60 C.D. Ann.

1-5/16" 17-4 PH H.R. A&P

1-3/8" 17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.416 C.D. Ann.

1-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.440 C H.R. A&PNitronic 60 C.D. Ann.

1-5/8" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.416 H.R. A&P

1-3/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P

7/8" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

15/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.316 C.D. Ann.316 L C.D. Ann.

1" 13-8 MO V.M. H.R. A&P15-5 PH V.M. C.F. Sol trt17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.420 C.D. Ann.440 C H.R. A&PNitronic 60 C.D. Ann.

1-1/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.

1-1/8" 17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1-3/16" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.

1-1/4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. C.F. Sol trt17-4 PH H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.303 Sel C.D. Ann.316 C.D. Ann.



35FRY STEEL COMPANY

(562) 802-2721


3" 316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&PNitronic 60 H.R. A&P

3-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&PNitronic 60 H.R. A&P

4-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P

5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P

5-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

6" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P

2" 304 H.R. A&P304 L H.R. A&P303 S C.D. Ann.303 Sel C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&PNitronic 60 H.R. A&P

2-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P

2-3/8" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P

2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&PNitronic 60 H.R. A&P

2-3/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P

3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P




[email protected]

(562) 802-2721




6" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P

STAINLESSFLATS

STOCKED IN 12' R/L


37FRY STEEL COMPANY

(562) 802-2721


1/8" X 1" 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.440 C H.R. A&P

1/8" x 1-1/4" 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.416 C.D. Ann.440 C H.R. A&P

1/8" x 1-1/2" 302 P/B H.R. A&P304 P/B H.R. A&P 304 L P/B H.R. A&P440 C H.R. A&P


1/8" x 2" 302 P/B H.R. A&P 304 P/B H.R. A&P304 L P/B H.R. A&P440 C H.R. A&P



1/8" x 3-1/2" 440 C H.R. A&P

1/8" x 4" 302 P/B H.R. A&P304 P/B H.R. A&P 304 L P/B H.R. A&P440 C H.R. A&P

1/8" x 5" 302 P/B H.R. A&P304 P/B H.R. A&P 304 L P/B H.R. A&P

1/8" x 6" 302 P/B H.R. A&P 304 P/B H.R. A&P304 L P/B H.R. A&P


3/16" x 1/4" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.

1/8" x 1/4" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.416 C.D. Ann.


1/8" x 1/2" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1/8" x 5/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.416 C.D. Ann.

1/8" x 3/4" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.440 C H.R. A&P

1/8" x 7/8" 17-4 PH C.F. Sol trt302 P/B H.R. A&P 304 P/B H.R. A&P 304 L P/B H.R. A&P303 S C.D. Ann.440 C H.R. A&P

1/8" x 1" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


3/16" x 1" 304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/16" x 1-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P 304 L C.D. Ann.304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/16" x 1-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/16" x 1-3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P

3/16" x 1/4" 303 S C.D. Ann.

3/16" x 3/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann. 416 C.D. Ann.

3/16" x 1/2" 17-4 PH C.F. Sol trt 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.440 C H.R. A&P

3/16" x 5/8" 17-4 PH C.F. Sol trt 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.440 C H.R. A&P

3/16" x 3/4" 17-4 PH C.F. Sol trt302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P 304 L C.D. Ann.304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.440 C H.R. A&P

3/16" x 7/8" 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.

3/16" x 1" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


39FRY STEEL COMPANY

(562) 802-2721



1/4" x 1/2" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.347 C.D. Ann.403 C.D. Ann.410 C.D. Ann.416 C.D. Ann.

1/4" x 5/8" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P303 S C.D. Ann.416 C.D. Ann.

1/4" x 3/4" 17-4 PH C.F. Sol trt302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/4" x 7/8" 302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P

3/16" x 1-3/4" 304 L P/B H.R. A&P304 L H.R. A&P303 S H.R. A&P440 C H.R. A&P

3/16" x 2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/16" x 2-1/4" 302 P/B H.R. A&P 304 P/B H.R. A&P304 L P/B H.R. A&P

3/16" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P416 H.R. A&P440 C H.R. A&P

3/16" x 3" 15-5 PH V.M. H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P440 C H.R. A&P

3/16" x 3-1/2" 440 C H.R. A&P




3/16" x 8" 302 P/B H.R. A&P 304 P/B H.R. A&P304 L P/B H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


1/4" x 1-1/2" 303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

1/4" x 1-3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1/4" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/4" x 2-1/4" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

1/4" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P

1/4" x 7/8" 303 S H.R. A&P303 S C.D. Ann.

1/4" x 1" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

1/4" x 1-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/4" x 1-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


41FRY STEEL COMPANY

(562) 802-2721


1/4" x 5" 302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P

1/4" x 6" 302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P


5/16" x 3/8" 303 S C.D. Ann.

5/16" x 1/2" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P 303 S C.D. Ann.416 C.D. Ann.

5/16" x 5/8" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S C.D. Ann.

5/16" x 3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P 303 S H.R. A&P 303 S C.D. Ann.416 H.R. A&P 416 C.D. Ann.440 C H.R. A&P

5/16" x 7/8" 302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann.303 S H.R. A&P 303 S C.D. Ann.

5/16" x 1" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P

1/4" x 2-1/2" 302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1/4" x 2-3/4" 303 S H.R. A&P

1/4" x 3" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1/4" x 3-1/4" 303 S H.R. A&P

1/4" x 3-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P440 C H.R. A&P

1/4" x 4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1/4" x 4-1/2" 302 H.R. A&P 304 H.R. A&P 304 L H.R. A&P303 S H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


5/16" x 2" 304 L P/B H.R. A&P 303 S H.R. A&P 303 S C.D. Ann.316 H.R. A&P 316 L H.R. A&P 416 H.R. A&P 416 C.D. Ann.440 C H.R. A&P

5/16" x 2-1/4" 302 H.R. A&P304 H.R. A&P 304 L H.R. A&P 303 S H.R. A&P

5/16" x 2-1/2" 17-4 PH H.R. A&P302 H.R. A&P 304 H.R. A&P 304 L H.R. A&P 303 S H.R. A&P 303 S C.D. Ann.

5/16" X 3" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P 302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P 304 L P/B H.R. A&P 303 S H.R. A&P

5/16" x 4" 302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P 304 L P/B H.R. A&P

5/16" x 5" 302 H.R. A&P304 H.R. A&P 302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P 304 L P/B H.R. A&P

5/16" x 6" 302 P/B H.R. A&P 304 P/B H.R. A&P 304 L P/B H.R. A&P

3/8" x 1/2" 17-4 PH C.F. Sol trt302 C.D. Ann.304 C.D. Ann.304 L C.D. Ann. 303 S C.D. Ann.316 C.D. Ann.316 L C.D. Ann.321 C.D. Ann.416 C.D. Ann.

3/8" x 5/8" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.

5/16" x 1" 304 H.R. A&P 302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P 304 L C.D. Ann.304 L P/B H.R. A&P 303 S H.R. A&P 303 S C.D. Ann.316 H.R. A&P 316 L H.R. A&P 416 H.R. A&P 416 C.D. Ann.440 C H.R. A&P

5/16" x 1-1/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P416 H.R. A&P416 C.D. Ann.

5/16" x 1-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P 316 L H.R. A&P 416 H.R. A&P 416 C.D. Ann.440 C H.R. A&P

5/16" x 1-3/4" 302 H.R. A&P304 H.R. A&P 304 L H.R. A&P 303 S H.R. A&P

5/16" x 2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P 304 H.R. A&P 302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


43FRY STEEL COMPANY

(562) 802-2721


3/8" x 1-1/4" 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 1-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 1-3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P440 C H.R. A&P

3/8" x 2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P

3/8" x 5/8" 303 S H.R. A&P303 S C.D. Ann.416 H.R. A&P416 C.D. Ann.

3/8" x 3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 7/8" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

3/8" x 1" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

3/8" x 1-1/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


3/8" x 4" 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 4-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

3/8" x 5" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P 303 S H.R. A&P316 H.R. A&P316 L H.R. A&P416 H.R. A&P440 C H.R. A&P

3/8" x 6" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P416 H.R. A&P


7/16" x 3/4" 303 S H.R. A&P

7/16" x 1" 303 S H.R. A&P

1/2" x 5/8" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.416 H.R. A&P416 C.D. Ann.

1/2" x 3/4" 17-4 PH H.R. A&P302 H.R. A&P

3/8" x 2" 403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 2-1/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

3/8" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P 304 L P/B H.R. A&P 303 S H.R. A&P 303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/8" x 2-3/4" 440 C H.R. A&P

3/8" x 3" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P


3/8" x 4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


45FRY STEEL COMPANY

(562) 802-2721


1/2" x 1-1/4" 316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/2" x 1-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

1/2" x 1-3/4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1/2" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P304 P/B H.R. A&P

1/2" x 3/4" 304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/2" x 7/8" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

1/2" x 1" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

1/2" x 1-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.


1/2" x 3" 416 C.D. Ann.440 C H.R. A&P

1/2" x 3-1/4" 17-4 PH H.R. A&P

1/2" x 3-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P

1/2" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/2" x 4-1/4" 17-4 PH H.R. A&P


1/2" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P416 H.R. A&P440 C H.R. A&P

1/2" x 5-1/2" 303 S H.R. A&P

1/2" x 6" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P

STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


1/2" x 2" 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

1/2" x 2-1/4" 17-4 PH H.R. A&P303 S H.R. A&P303 S C.D. Ann.

1/2" x 2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

1/2" x 2-3/4" 13-8 MO V.M. H.R. A&P303 S H.R. A&P

1/2" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L C.D. Ann.304 L P/B H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


47FRY STEEL COMPANY

(562) 802-2721


5/8" x 1-1/4" 440 C H.R. A&P

5/8" x 1-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

5/8" x 1-3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.416 H.R. A&P440 C H.R. A&P

5/8" x 2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P


5/8" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1/2" x 6" 302 P/B H.R. A&P 304 P/B H.R. A&P 304 L H.R. A&P304 L P/B H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P416 H.R. A&P440 C H.R. A&P



5/8" x 3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.416 H.R. A&P416 C.D. Ann.

5/8" x 7/8" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

5/8" x 1" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

5/8" x 1-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.321 H.R. A&P416 H.R. A&P416 C.D. Ann.


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


3/4" x 1" 303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

3/4" x 1-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/4" x 1-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P

3/4" x 1-3/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

5/8" x 2-1/2" 303 S C.D. Ann.416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

5/8" x 2-3/4" 17-4 PH H.R. A&P

5/8" x 3" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

5/8" x 3-1/4" 17-4 PH H.R. A&P

5/8" x 3-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P

5/8" x 4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.416 H.R. A&P416 C.D. Ann.

5/8" x 4-1/4" 17-4 PH H.R. A&P

5/8" x 4-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

5/8" x 5" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P

5/8" x 5-1/2" 17-4 PH H.R. A&P

5/8" x 6" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P

3/4" x 1" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.



STAINLESSFLATS

STOCKED IN 12' R/L


49FRY STEEL COMPANY

(562) 802-2721


3/4" x 3" 303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/4" x 3-1/4" 17-4 PH H.R. A&P303 S H.R. A&P

3/4" x 3-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

3/4" x 4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/4" x 4-1/4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P


3/4" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P

3/4" x 5-1/2" 17-4 PH H.R. A&P

3/4" x 6" 15-5 PH V.M. H.R. A&P

3/4" x 1-3/4" 321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/4" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.420 H.R. A&P440 C H.R. A&P


3/4" x 2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P416 C.D. Ann.440 C H.R. A&P

3/4" x 2-3/4" 17-4 PH H.R. A&P

3/4" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


1" x 1-1/4" 316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1" x 1-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1" x 1-3/4" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P416 H.R. A&P

1" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1" x 2-1/4" 17-4 PH H.R. A&P

3/4" x 6" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

3/4" x 8" 17-4 PH H.R. A&P

7/8" x 1" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P



7/8" x 2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

7/8" x 2-1/4" 17-4 PH H.R. A&P303 S H.R. A&P

7/8" x 2-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

7/8" x 2-3/4" 17-4 PH H.R. A&P

7/8" x 3" 17-4 PH H.R. A&P303 S H.R. A&P

7/8" x 3-1/2" 17-4 PH H.R. A&P

7/8" x 4" 17-4 PH H.R. A&P303 S H.R. A&P

7/8" x 5-3/4" 15-5 PH V.M. H.R. A&P

1" x 1-1/4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


51FRY STEEL COMPANY

(562) 802-2721


1" x 4" 304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1" x 4-1/4" 17-4 PH H.R. A&P

1" x 4-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1" x 5-1/2" 17-4 PH H.R. A&P

1" x 6" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1" x 7" 17-4 PH H.R. A&P

1" x 8" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P

1-1/8" x 1-1/4" 17-4 PH H.R. A&P303 S H.R. A&P

1-1/8" x 1-3/8" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P

1-1/8" x 1-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P

1" x 2-1/4" 302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.

1" x 2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.304 L H.R. A&P304 L C.D. Ann.303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1" x 3-1/4" 17-4 PH H.R. A&P303 S H.R. A&P

1" x 3-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P

1" x 3-3/4" 17-4 PH H.R. A&P

1" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann.304 C.D. Ann.


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721


1-1/4" x 2-1/4" 304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-1/4" x 2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1-1/4" x 2-3/4" 17-4 PH H.R. A&P

1-1/4" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1-1/4" x 3-1/4" 17-4 PH H.R. A&P440 C H.R. A&P

1-1/4" x 3-1/2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-1/4" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P416 H.R. A&P403 H.R. A&P410 H.R. A&P440 C H.R. A&P

1-1/4" x 4-1/4" 17-4 PH H.R. A&P

1-1/4" x 4-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

1-1/8" x 1-1/2" 303 S H.R. A&P

1-1/8" x 1-3/4" 17-4 PH H.R. A&P303 S H.R. A&P

1-1/8" x 2" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P




1-1/4" x 1-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440C H.R. A&P

1-1/4" x 1-3/4" 17-4 PH H.R. A&P303 S H.R. A&P303 S C.D. Ann.

1-1/4" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 S C.D. Ann.316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1-1/4" x 2-1/4" 17-4 PH H.R. A&P302 H.R. A&P



STAINLESSFLATS

STOCKED IN 12' R/L


53FRY STEEL COMPANY

(562) 802-2721


1-1/2" x 2-3/4" 17-4 PH H.R. A&P

1-1/2" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

1-1/2" x 3-1/4" 17-4 PH H.R. A&P303 S H.R. A&P


1-1/2" x 3-3/4" 17-4 PH H.R. A&P

1-1/2" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

1-1/2" x 4-1/4" 17-4 PH H.R. A&P

1-1/2" x 4-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

1-1/2" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P303 S H.R. A&P416 H.R. A&P

1-1/2" x 5-1/2" 17-4 PH H.R. A&P

1-1/2" x 6" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P403 H.R. A&P410 H.R. A&P

1-1/4" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-1/4" x 6" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P

1-3/8" x 2" 15-5 PH V.M. H.R. A&P

1-3/8" x 2-1/2" 15-5 PH V.M. H.R. A&P


1-1/2" x 2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P303 Sel Hi tens C.F. “B”316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P


1-1/2" x 2-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721




2" x 2-1/4" 304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

2" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P321 H.R. A&P416 H.R. A&P

2" x 2-3/4" 17-4 PH H.R. A&P

2" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P302 C.D. Ann304 C.D. Ann304 L H.R. A&P304 L C.D. Ann303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P420 H.R. A&P440 C H.R. A&P

2" x 3-1/4" 17-4 PH H.R. A&P

2" x 3-1/2" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P303 S H.R. A&P416 H.R. A&P

2" x 3-3/4" 17-4 PH H.R. A&P

2" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P347 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

2" x 4-1/4" 17-4 PH H.R. A&P

2" x 4-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

2" x 5" 13-8 MO V.M. H.R. A&P

1-1/2" x 6" 416 H.R. A&P440 C H.R. A&P

1-1/2" x 7" 17-4 PH H.R. A&P

1-1/2" x 8" 17-4 PH H.R. A&P

1-1/2" x 10" 17-4 PH H.R. A&P

1-1/2" x 12" 17-4 PH H.R. A&P



1-3/4" x 2-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-3/4" x 2-3/4" 17-4 PH H.R. A&P

1-3/4" x 3" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-3/4" x 3-1/4" 17-4 PH H.R. A&P

1-3/4" x 3-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P

1-3/4" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

1-3/4" x 4-1/2" 17-4 PH H.R. A&P


1-3/4" x 5-1/2" 17-4 PH H.R. A&P

1-3/4" x 6" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P303 S H.R. A&P

2" x 2-1/4" 302 H.R. A&P

STAINLESSFLATS

STOCKED IN 12' R/L


55FRY STEEL COMPANY

(562) 802-2721


2-1/2" x 6" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P440 C H.R. A&P

2-1/2" x 8" 17-4 PH H.R. A&P

3" x 3-1/2" 17-4 PH H.R. A&P303 S H.R. A&P

3" x 4" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P403 H.R. A&P410 H.R. A&P416 H.R. A&P440 C H.R. A&P

3" x 4-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P

3" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P321 H.R. A&P416 H.R. A&P

3" x 5-1/2" 17-4 PH H.R. A&P

3" x 6" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P316 H.R. A&P316 L H.R. A&P321 H.R. A&P416 H.R. A&P440 C H.R. A&P

3" x 7" 17-4 PH H.R. A&P

3" x 8" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P303 S H.R. A&P440 C H.R. A&P

3-1/2" x 4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P

2" x 5" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P

2" x 5-1/2" 17-4 PH H.R. A&P

2" x 6" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P416 H.R. A&P440 C H.R. A&P

2" x 6-1/2" 17-4 PH H.R. A&P

2" x 7" 17-4 PH H.R. A&P

2" x 8" 17-4 PH H.R. A&P

2" x 9" 17-4 PH H.R. A&P

2" x 10" 17-4 PH H.R. A&P

2" x 12" 17-4 PH H.R. A&P

2-1/4" x 3" 15-5 PH V.M. H.R. A&P

2-1/4" x 4" 15-5 PH V.M. H.R. A&P

2-1/4" x 6" 15-5 PH V.M. H.R. A&P


2-1/2" x 3-1/4" 17-4 PH H.R. A&P

2-1/2" x 3-1/2" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P303 S H.R. A&P

2-1/2" x 3-3/4" 17-4 PH H.R. A&P

2-1/2" x 4" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P440 C H.R. A&P

2-1/2" x 4-1/2" 17-4 PH H.R. A&P

2-1/2" x 5" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P440 C H.R. A&P

2-1/2" x 5-1/2" 17-4 PH H.R. A&P


STAINLESSFLATS

STOCKED IN 12' R/L


[email protected]

(562) 802-2721




4" x 6" 15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

4" x 8" 13-8 MO V.M. H.R. A&P15-5 PH V.M. H.R. A&P17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P

3-1/2" x 4" 304 L H.R. A&P

3-1/2" x 5" 17-4 PH H.R. A&P


3-1/2" x 8" 17-4 PH H.R. A&P

4" x 5" 17-4 PH H.R. A&P302 H.R. A&P304 H.R. A&P304 L H.R. A&P303 S H.R. A&P

4" x 6" 13-8 MO V.M. H.R. A&P

STAINLESS WEIGHTS

ROUNDS


57FRY STEEL COMPANY

(562) 802-2721

Estimated Weight, Lbs.Size in Inches Per Inch Per Foot 12 Ft. Bar


1/16" .001 .010 .125/64" .001 .016 .193/32" .002 .023 .287/64" .003 .032 .381/8" .004 .042 .50.130" .004 .0451 .549/64" .004 .053 .645/32" .005 .065 .7811/64" .007 .079 .953/16" .008 .094 1.13.1925" .008 .0989 1.186.1975" .009 .104 1.24813/64" .009 .110 1.327/32" .011 .128 1.5415/64" .012 .147 1.761/4" .014 .167 2.00.255" .014 .1736 2.083.260" .015 .1805 2.16617/64" .016 .188 2.2569/32" .018 .211 2.5319/64" .019 .235 2.825/16" .022 .261 3.13.3175" .022 .269 3.228.3225" .023 .277 3.3221/64" .024 .287 3.4411/32" .026 .316 3.7923/64" .029 .345 4.143/8" .031 .376 4.51.380" .032 .3855 4.62.385" .033 .395 4.7425/64" .034 .407 4.8813/32" .037 .441 5.2927/64" .039 .475 5.707/16" .043 .511 6.13.4425" .044 .5225 6.27.4475" .045 .535 6.4229/64" .046 .548 6.57615/32" .049 .587 7.0431/64" .052 .626 7.511/2" .056 .668 8.02.505" .057 .680 8.16.510" .058 .694 8.3333/64" .059 .710 8.5217/32" .063 .754 9.059/16" .070 .845 10.14.5675" .072 .860 10.32.5725" .073 .875 10.50.5775" .074 .891 10.6937/64" .074 .892 10.7019/32" .078 .941 11.295/8" .087 1.043 12.52.630" .088 1.060 12.72.635" .090 1.076 12.91.640" .091 1.093 13.1241/64" .092 1.096 13.1521/32" .096 1.150 13.8011/16" .105 1.262 15.14.6925" .107 1.280 15.37

23/32" .115 1.379 16.553/4" .125 1.502 18.02.755" .127 1.522 18.26.760" .128 1.54 18.4849/64" .131 1.565 18.7825/32" .136 1.630 19.5613/16" .147 1.763 21.16.8175" .149 1.784 21.4227/32" .158 1.901 22.817/8" .170 2.044 24.53.880" .172 2.067 24.81.885" .174 2.091 25.0957/64" .177 2.118 25.4229/32" .183 2.193 26.3215/16" .192 2.347 28.16.9425" .198 2.372 28.4631/32" .209 2.506 30.07

1" .22 2.670 32.041.005" .22 2.696 32.381.010" .23 2.723 32.671/64" .23 2.750 33.001.020" .23 2.778 33.341/16" .25 3.014 36.173/32" .27 3.194 38.331/8" .28 3.379 40.551.135" .29 3.440 41.289/64" .29 3.470 41.641.145" .29 3.500 42.005/32" .30 3.570 42.843/16" .31 3.766 45.191/4" .35 4.173 50.081.260" .35 4.240 50.8817/64" .36 4.276 51.311.275" .36 4.340 52.089/32" .37 4.384 52.605/16" .38 4.600 55.203/8" .42 5.049 60.591.385" .43 5.122 61.4613/32" .44 5.279 63.357/16" .46 5.518 66.221/2" .50 6.008 72.101.510" .507 6.088 73.0501.515" .505 6.057 72.68417/32" .52 6.261 75.139/16" .54 6.520 78.245/8" .59 7.051 84.6111/16" .64 7.604 91.253/4" .68 8.178 98.141.770" .70 8.365 100.3813/16" .73 8.773 105.307/8" .78 9.388 112.7015/16" .84 10.020 120.20

2" .89 10.680 128.202.020" .91 10.896 130.751/16" .95 11.360 136.301/8" 1.01 12.06 144.7

STAINLESS WEIGHTS

ROUNDS


[email protected]

(562) 802-2721



2"3/16" 1.07 12.78 153.41/4" 1.13 13.52 162.22.270" 1.15 13.76 165.125/16" 1.19 14.28 171.43/8" 1.26 15.06 180.77/16" 1.33 15.87 190.41/2" 1.39 16.69 200.32.520" 1.41 16.957 203.489/16" 1.46 17.53 210.45/8" 1.54 18.40 220.811/16" 1.61 19.29 231.53/4" 1.69 20.20 242.42.770" 1.71 20.489 245.8713/16" 1.76 21.12 253.47/8" 1.84 22.07 264.815/16" 1.92 23.04 276.5

3" 2.01 24.03 288.43.020" 2.03 24.354 292.251/16" 2.09 25.05 300.61/8" 2.18 26.08 312.93/16" 2.27 27.13 325.61/4" 2.36 28.21 338.53.270" 2.38 28.551 342.615/16" 2.45 29.30 351.63/8" 2.54 30.42 365.07/16" 2.64 31.55 378.61/2" 2.73 32.71 392.53.520" 2.76 33.082 396.993.530" 2.77 33.273 399.255/8" 2.93 35.09 421.111/16" 3.03 36.31 435.73/4" 3.14 37.55 450.63.770" 3.16 37.948 455.397/8" 3.35 40.10 481.215/16" 3.45 41.40 496.8

4" 3.56 42.73 512.64.020" 3.60 43.148 517.784.030" 3.61 43.363 520.361/8" 3.79 45.43 545.21/4" 4.02 48.23 578.73/8" 4.26 51.11 613.37/16" 4.39 52.58 630.91/2" 4.51 54.07 648.94.530" 4.57 54.795 657.495/8" 4.76 57.12 685.43/4" 5.03 60.25 723.07/8" 5.29 63.45 761.515/16" 5.42 65.10 781.2

5" 5.56 66.75 801.11/8" 5.84 70.13 841.61/4" 6.13 73.60 883.23/8" 6.43 77.15 925.77/16" 6.60 78.95 947.41/2" 6.73 80.77 969.2

5"5/8" 7.04 84.48 1013.83/4" 7.36 88.29 1059.015/16" 7.84 94.14 1130.0

6" 8.01 96.12 1153.51/8" 8.35 100.2 1202.41/4" 8.71 104.3 1252.01/2" 9.40 112.8 1353.83/4" 10.14 121.7 1460.0

7" 10.90 130.8 1570.81/4" 11.70 140.4 1684.11/2" 12.52 150.2 1802.23/4" 13.36 160.4 1924.4

8" 14.24 170.9 2050.61/4" 15.14 181.7 2180.71/2" 16.08 192.9 2315.03/4" 17.04 204.5 2453.1

9" 18.02 216.3 2595.21/4" 19.04 228.5 2741.41/2" 20.08 241.0 2891.63/4" 21.15 253.8 3045.8

10" 22.25 267.0 3204.01/2" 24.53 294.4 3532.4

11" 26.92 324.0 3876.81/2" 29.43 354.0 4237.3

12" 32.04 384.48 4613.761/2" 34.77 417.2 5006.2

13" 37.60 451.23 5414.761/2" 40.55 487.0 5839.3

14" 43.61 523.32 6279.84

15" 50.06 601.0 7209.0

16" 56.96 684.0 8202.2

17" 64.42 773.0 9276.0

18" 72.17 866.0 10,392.0

19" 80.32 963.87 11,566.44

20" 89.17 1070.0 12,840.00

22" 106.60 1279.0 15,348.0

23" 116.30 1396.0 16,752.0

24" 126.70 1520.0 18,240.0

1/8" .004 .046 .555/32" .006 .072 .8643/16" .009 .104 1.257/32" .012 .140 1.681/4" .015 .184 2.219/32" .019 .232 2.795/16" .02 .288 3.4611/32" .03 .348 4.143/8" .03 .414 4.9713/32" .04 .4857 5.8287/16" .05 .564 6.771/2" .06 .736 8.839/16" .08 .932 11.185/8" .10 1.150 13.8011/16" .12 1.392 16.703/4" .14 1.656 19.8713/16" .16 1.944 23.337/8" .19 2.254 27.0515/16" .22 2.588 31.06

1" .25 2.945 35.341/16" .28 3.324 39.891/8" .31 3.727 44.723/16" .35 4.152 49.821/4" .38 4.601 55.215/16" .42 5.072 60.86

1"3/8" .46 5.567 66.807/16" .51 6.085 73.021/2" .55 6.625 79.509/16" .60 7.190 86.285/8" .65 7.775 93.3011/16" .70 8.385 100.603/4" .75 9.019 108.2313/16" .81 9.673 116.11-7/8" .86 10.35 124.2

2" .98 11.78 141.41/8" 1.11 13.30 159.63/16" 1.17 14.09 169.11/4" 1.24 14.91 178.93/8" 1.38 16.61 199.31/2" 1.53 18.40 220.85/8" 1.69 20.29 243.53/4" 1.86 22.27 267.27/8" 2.03 24.33 292.0

3" 2.21 26.50 318.01/2" 3.01 36.07 432.8

4" 3.93 47.12 565.4

STAINLESS WEIGHTSHEXAGONS

SQUARES


59FRY STEEL COMPANY

(562) 802-2721





1/8" .004 .053 .6365/32" .006 .083 .9963/16" .010 .120 1.4361/4" .017 .213 2.5505/16" .03 .332 3.9813/8" .04 .478 5.7367/16" .05 .651 7.8101/2" .07 .850 10.2009/16" .09 1.076 12.9105/8" .11 1.328 15.94011/16" .12 1.607 19.293/4" .16 1.913 22.96013/16" .19 2.245 26.9407/8" .22 2.603 31.24015/16" .25 2.988 35.856

1" .28 3.400 40.801/16" .32 3.840 46.061/8" .36 4.303 51.643/16" .40 4.795 57.541/4" .44 5.313 63.765/16" .49 5.857 70.293/8" .54 6.428 77.14

1"1/2" .64 7.650 91.805/8" .75 8.980 107.743/4" .87 10.410 124.957/8" 1.00 11.950 143.44

2" 1.13 13.600 163.201/8" 1.28 15.353 184.241/4" 1.43 17.21 206.63/8" 1.60 19.18 230.21/2" 1.77 21.25 255.03/4" 2.14 25.72 308.6

3" 2.55 30.6 367.21/2" 3.47 41.65 500.0

4" 4.53 54.4 652.81/2" 5.74 68.85 826.2

5" 7.08 85.0 1020.01/2" 8.58 102.9 1234.0

6" 10.2 122.4 1469.0

STAINLESS WEIGHTS

FLATS


[email protected]

(562) 802-2721



1/8" x 3/16" .007 .072 .8641/4" .009 .106 1.275/16" .011 .133 1.603/8" .013 .159 1.917/16" .016 .186 2.231/2" .018 .213 2.565/8" .022 .266 3.193/4" .027 .319 3.837/8" .031 .372 4.461" .035 .425 5.101-1/8" .040 .480 5.761-1/4" .044 .531 6.371-3/8" .049 .588 7.061-1/2" .053 .638 7.661-5/8" .058 .696 8.351-3/4" .062 .744 8.932" .071 .850 10.202-1/4" .080 .956 11.472-1/2" .089 1.063 12.762-3/4" .097 1.160 13.903" .106 1.275 15.303-1/4" .115 1.380 16.563-1/2" .124 1.488 17.864" .142 1.700 20.404-1/2" .159 1.913 22.965" .177 2.125 25.506" .213 2.550 30.608" .283 3.400 40.80

3/16" x 1/4" .013 .160 1.925/16" .017 .199 2.393/8" .020 .239 2.877/16" .023 .279 3.351/2" .027 .319 3.835/8" .033 .398 4.783/4" .040 .478 5.747/8" .047 .558 6.701" .053 .638 7.661-1/8" .060 .717 8.601-1/4" .066 .797 9.561-3/8" .073 .877 10.521-1/2" .080 .956 11.471-3/4" .093 1.116 13.392" .106 1.275 15.302-1/4" .120 1.440 17.282-1/2" .133 1.594 19.132-3/4" .146 1.750 21.003" .159 1.913 22.963-1/2" .186 2.231 26.774" .213 2.550 30.604-1/2" .239 2.870 34.405" .266 3.188 38.266" .319 3.825 45.908" .425 5.100 61.20

1/4" x 5/16" .022 .266 3.193/8" .027 .319 3.837/16" .031 .372 4.461/2" .035 .425 5.10

1/4" x 9/16" .040 .480 5.765/8" .040 .531 6.373/4" .053 .628 7.667/8" .062 .744 8.931" .071 .850 10.201-1/8" .080 .956 11.471-1/4" .089 1.063 12.761-3/8" .097 1.160 13.901-1/2" .106 1.275 15.301-5/8" .115 1.380 16.561-3/4" .124 1.488 17.862" .142 1.700 20.402-1/4" .159 1.913 22.962-1/2" .177 2.125 25.502-3/4" .195 2.340 28.083" .213 2.550 30.603-1/4" .230 2.760 33.123-1/2" .248 2.975 35.704" .283 3.400 40.804-1/2" .319 3.825 45.905" .354 4.250 51.005-1/2" .390 4.680 56.206" .425 5.100 61.207" .496 5.950 71.408" .567 6.800 81.60

5/16" x 3/8" .033 .398 4.787/16" .039 .460 5.521/2" .044 .531 6.375/8" .055 .664 7.973/4" .066 .797 9.567/8" .078 .930 11.161" .089 1.063 12.761-1/8" .099 1.200 14.401-1/4" .111 1.328 15.941-1/2" .133 1.594 19.131-3/4" .155 1.859 22.312" .177 2.125 25.502-1/4" .199 2.390 28.652-1/2" .221 2.656 31.862-3/4" .244 2.930 35.163" .266 3.188 38.263-1/2" .310 3.719 44.634" .354 4.250 51.004-1/2" .398 4.776 57.315" .443 5.313 63.766" .531 6.375 76.508" .708 8.500 102.00

3/8" x 7/16" .046 .576 6.911/2" .053 .638 7.669/16" .060 .720 8.645/8" .066 .797 9.563/4" .080 .956 11.477/8 .093 1.116 13.391" .106 1.275 15.301-1/8" .120 1.430 17.161-1/4" .133 1.594 19.131-3/8" .146 1.750 21.00

STAINLESS WEIGHTS

FLATS-Continued


61FRY STEEL COMPANY

(562) 802-2721



3/8" x 1-1/2" .159 1.913 22.961-3/4" .186 2.231 26.772" .213 2.550 30.602-1/4" .239 2.869 34.432-1/2" .266 3.188 38.262-3/4" .292 3.500 42.003" .319 3.825 45.903-1/4" .345 4.140 49.683-1/2" .372 4.463 53.564" .425 5.100 61.204-1/2" .478 5.738 68.865" .531 6.375 76.505-1/2" .584 7.010 84.106" .637 7.650 91.807" .744 8.928 107.138" .850 10.200 122.40

7/16" x 1/2" .062 .744 8.935/8" .078 .929 11.153/4" .093 1.116 13.397/8" .109 1.344 16.131" .124 1.488 17.861-1/4" .155 1.859 22.311-1/2" .186 2.231 26.771-3/4" .217 2.600 31.202" .248 2.975 35.702-1/2" .310 3.720 44.603" .372 4.460 53.504" .496 5.950 71.40

1/2" x 9/16" .080 .960 11.525/8" .089 1.063 12.763/4" .106 1.275 15.307/8" .124 1.488 17.861" .142 1.700 20.401-1/8" .159 1.920 23.001-1/4" .177 2.125 25.501-3/8" .195 2.340 28.001-1/2" .213 2.550 30.601-5/8" .230 2.760 33.121-3/4" .248 2.975 35.702" .283 3.400 40.802-1/4" .319 3.825 45.902-1/2" .354 4.250 51.002-3/4" .390 4.675 56.103" .425 5.100 61.203-1/4" .460 5.524 66.243-1/2" .496 5.950 71.404" .567 6.800 81.604-1/4" .602 7.225 86.704-1/2" .637 7.650 91.805" .708 8.500 102.005-1/2" .779 9.350 112.206" .850 10.200 122.406-1/2" .921 11.052 132.627" .992 11.904 142.848" 1.130 13.600 163.20

9/16" x 5/8" .100 1.200 14.40

9/16" x 3/4" .120 1.440 17.281" .159 1.910 22.901-1/4" .199 2.390 28.701-1/2" .239 2.870 34.442" .319 3.830 45.96

5/8" x 3/4" .133 1.594 19.137/8" .155 1.859 22.311" .177 2.125 25.501-1/8" .199 2.390 28.601-1/4" .221 2.656 31.871-3/8" .244 2.930 35.161-1/2" .266 3.188 38.261-5/8" .288 3.454 41.451-3/4" .310 3.719 44.632" .354 4.250 51.002-1/4" .398 4.781 57.372-1/2" .438 5.313 63.762-3/4" .487 5.840 70.003" .531 6.375 76.503-1/4" .576 6.906 82.873-1/2" .620 7.438 89.264" .708 8.500 102.004-1/4" .752 9.031 108.284-1/2" .797 9.560 114.705" .885 10.630 127.605-1/2" .974 11.690 140.306" 1.060 12.750 153.007" 1.240 14.880 178.568" 1.420 17.000 204.00

3/4" x 7/8" .186 2.230 26.771" .213 2.550 30.601-1/8" .239 2.880 34.561-1/4" .266 3.188 38.261-3/8" .292 3.500 42.001-1/2" .319 3.825 45.901-5/8" .345 4.140 49.681-3/4" .372 4.463 53.562" .425 5.100 61.202-1/4" .478 5.738 68.862-1/2" .531 6.375 76.602-3/4" .584 7.000 84.003" .637 7.650 91.803-1/4" .691 8.290 99.483-1/2" .744 8.925 107.004" .850 10.200 122.404-1/4" .903 10.840 130.054-1/2" .956 11.470 137.605" 1.060 12.750 153.005-1/2" 1.170 14.040 168.506" 1.280 15.300 186.306-1/2" 1.380 16.560 198.727" 1.490 17.880 214.568" 1.700 20.400 244.80

7/8" x 1" .248 2.975 35.701-1/8" .279 3.350 40.201-1/4" .310 3.719 44.63

STAINLESS WEIGHTS

FLATS-Continued


[email protected]

(562) 802-2721



7/8" x 1-3/8" .341 4.090 49.001-1/2" .372 4.463 53.561-3/4" .434 5.206 62.472" .496 5.950 71.402-1/4" .558 6.696 80.352-1/2" .620 7.438 89.262-3/4" .682 8.180 98.163" .744 8.925 107.103-1/2" .868 10.410 124.904" .992 11.900 142.804-1/2" 1.120 13.440 161.285" 1.240 14.880 178.505-3/4" 1.426 17.110 205.32

1" x 1-1/8" .319 3.828 45.931-1/4" .354 4.250 51.001-3/8" .390 4.680 56.161-1/2" .425 5.100 61.201-5/8" .460 5.523 66.271-3/4" .496 5.950 71.402" .567 6.800 81.602-1/4" .637 7.650 92.332-1/2" .708 8.500 102.002-3/4" .779 9.350 112.203" .850 10.200 122.403-1/4" .921 11.050 132.603-1/2" .992 11.900 142.803-3/4" 1.060 12.750 153.004" 1.130 13.600 163.204-1/4" 1.200 14.450 173.404-1/2" 1.280 15.300 183.605" 1.420 17.000 204.005-1/2" 1.560 18.720 224.646" 1.700 20.400 244.806-1/2" 1.840 22.080 264.967" 1.980 23.800 285.608" 2.270 27.200 326.40

1-1/8"x 1-1/4" .399 4.780 57.381-3/8" .438 5.260 63.121-1/2" .478 5.740 68.851-3/4" .558 6.694 80.332" .638 7.650 91.802-1/4" .717 8.606 103.282-1/2" .797 9.560 114.753" .956 11.470 137.664" 1.270 15.280 183.36

1-1/4"x 1-3/8" .487 5.840 70.131-1/2" .531 6.375 76.501-5/8" .576 6.900 82.801-3/4" .620 7.438 89.262" .708 8.500 102.002-1/4" .797 9.563 114.802-1/2" .885 10.630 127.602-3/4" .974 11.690 140.003" 1.060 12.750 153.003-1/4" 1.150 13.800 165.603-1/2" 1.240 14.880 178.60

1-1/4"x 4" 1.420 17.000 204.004-1/4" 1.510 18.062 216.754-1/2" 1.590 19.126 229.515" 1.770 21.250 255.006" 2.130 25.500 306.00

1-3/8"x 1-1/2" .584 7.010 84.122" .779 9.348 112.182-1/2" .974 11.690 140.283" 1.170 14.040 168.48

1-1/2"x 1-3/4" .744 8.92 107.102" .850 10.20 122.402-1/4" .956 11.48 137.802-1/2" 1.060 12.75 153.002-3/4" 1.170 14.04 168.483" 1.280 15.30 183.603-1/4" 1.380 17.50 198.903-1/2" 1.490 17.85 214.203-3/4" 1.590 19.13 229.514" 1.700 20.40 244.804-1/4" 1.810 21.68 260.124-1/2" 1.910 22.92 275.045" 2.130 25.50 306.005-1/2" 2.340 28.08 336.966" 2.550 30.60 367.207" 2.980 35.70 428.408" 3.400 40.80 489.6010" 4.250 51.00 612.0012 " 5.100 61.20 734.40

1-3/4"x 2" .992 11.90 142.802-1/4" 1.120 13.44 161.282-1/2" 1.240 14.88 178.602-3/4" 1.360 16.32 195.803" 1.490 17.85 214.203-1/4" 1.610 19.34 232.063-1/2" 1.740 20.88 250.604" 1.980 23.80 285.604-1/2" 2.230 26.78 321.315" 2.480 29.76 357.205-1/2" 2.730 32.73 392.706" 2.980 35.70 428.40

2" x 2-1/4" 1.280 15.36 184.302-1/2" 1.420 17.00 204.002-3/4" 1.560 18.72 224.603" 1.700 20.40 244.803-1/4" 1.840 22.10 265.203-1/2" 1.980 23.80 285.603-3/4" 2.130 25.50 306.004" 2.270 27.20 326.004-1/4" 2.410 28.90 346.804-1/2" 2.550 30.60 367.005" 2.830 34.00 408.005-1/2" 3.120 37.44 449.286" 3.400 40.80 489.606-1/2" 3.680 44.20 530.407" 3.970 47.60 571.20

STAINLESS WEIGHTS

FLATS-Continued


63FRY STEEL COMPANY

(562) 802-2721



2" x 8" 4.530 54.40 652.809" 5.10 61.20 734.4010" 5.67 68.00 816.0012" 6.80 81.60 979.20

2-1/4"x 2-1/2" 1.59 19.13 229.503" 1.91 22.95 275.404" 2.55 30.60 367.204-1/2" 2.87 34.43 413.105" 3.19 38.25 459.006" 3.83 45.90 551.00

2-1/2"x 3" 2.13 25.50 306.003-1/4" 2.30 27.63 331.503-1/2" 2.48 29.75 357.003-3/4" 2.66 31.88 382.514" 2.83 34.00 408.004-1/2" 3.19 38.25 459.005" 3.54 42.50 510.005-1/2" 3.90 46.75 561.006" 4.25 51.00 612.00

2-1/2"x 8" 5.67 68.00 816.00

3" x 3-1/2" 2.98 35.76 429.124" 3.40 40.80 489.604-1/2" 3.83 45.90 551.005" 4.25 51.00 612.005-1/2" 4.68 56.10 673.206" 5.10 61.20 734.407" 5.95 71.40 856.808" 6.80 81.60 979.20

3-1/2"x 4" 3.97 47.60 571.005" 4.96 59.50 714.006" 5.95 71.40 857.008" 7.93 95.20 1142.40

4" x 5" 5.67 68.04 816.486" 6.80 81.60 979.208" 9.07 108.84 1306.08

SIZE TOLERANCES*

STAINLESS


[email protected]

(562) 802-2721

1/8" to 1/2" Over 1/2" Over 1" Over 2"Incl. To 1" Incl. To 2" Incl. To 4"Incl. Over Under

Up to 1" 0.008 0.010 – – – 0.015 0.015incl.

Over 1" to 2" 0.012 0.015 0.031 – – 0.031 0.031incl.

Over 2" to 4" 0.015 0.020 0.031 0.062 0.031 0.062 0.031incl.

Over 4" to 6" 0.015 0.020 0.031 0.062 0.031 0.093 0.062incl.

Over 6" to 8" 0.016 0.025 0.031 0.062 0.031 0.125 0.156incl.

Over 8" to 10" 0.021 0.031 0.031 0.062 0.031 0.156 0.156incl.

Over 10" to 12" – – 0.031 0.062 0.031 0.156 0.156incl.

SpecifiedWidths

In.

Corner RadiiNominal Sizes** Nominal

Inclusive, Corner Radii,In. In. Max

2" to 2-7/16" 5/16"2-1/2" to 2-7/8" 3/8"3" to 3-3/8" 7/16"3-1/2" to 3-7/8" 1/2"4" to 4-3/8" 5/8"4-1/2" to 6" 3/4"

WidthTolerances,

In.

Thickness Tolerance, In.,For Thickness Given

Over and Under

HOT ROLLED BARS FLATS

HOT ROLLED AND ROUGH TURNEDROUNDS or HOT ROLLED SQUARES

Size Tolerance, InchesSquare or HexagonsOver Under

.050" to 5/16" excl. 0 .0025/16" to 1/2" excl. 0 .0031/2" to 1" incl. .004Over 1" to 2" incl. 0 .006Over 2" to 3" incl. 0 .008Over 3" to 4" incl. 0 .010

PER: ASTM A 484 (BAR) & ASTM A 555 ( WIRE)Note: PH Grades Double Size Tolerance

COLD DRAWN BARSHEXAGONS AND SQUARES

1/16" to 9/32" .001 .0015/16" to 11/32" .0015 .00153/8" to 15/32" .0015 .0015

1/2" to 19/32" .002 .0025/8" to 31/32" .002 .0021" to 1-15/32" .0025 .0025

1-1/2" to 2-3/4" .003 .0032-13/16" to 3" .003 .0033-1/8" to 4" .003 .003

COLD DRAWN OR CENTERLESS GROUNDBARS ROUNDS

Width Tolerance, In.,Over and Under

For Thicknesses For Thicknesses1/4 in., and Under Over 1/4 in.

3/8" to 1" incl. 0.004 0.002Over 1" to 2" incl. 0.006 0.003Over 2" to 3" incl. 0.008 0.004Over 3" to 4-1/2" incl. 0.010 0.005

Thickness Tolerance, In.,Thickness, Inches Over or Under

1/8" to 1" incl. 0.002Over 1" to 2" incl. 0.003Over 2" to 3" incl. 0.004Over 3" to 4-1/2" incl 0.005

COLD DRAWN BARSFLATS

Over 5/16" to 7/16" 0.006 0.006 0.009Over 7/16" to 5/8" 0.007 0.007 0.010Over 5/8" to 7/8" 0.008 0.008 0.012Over 7/8" to 1" 0.009 0.009 0.013Over 1" to 1-1/8" 0.010 0.010 0.015

Over 1-1/8" to 1-1/4" 0.011 0.011 0.016Over 1-1/4" to 1-3/8" 0.012 0.012 0.018Over 1-3/8" to 1-1/2" 0.014 0.014 0.021Over 1-1/2" to 2" 1/64 1/64 0.023Over 2" to 2-1/2" 1/32 0 0.023

Over 2-1/2" to 3-1/2" 3/64 0 0.035Over 3-1/2" to 4-1/2" 1/16 0 0.046Over 4-1/2" to 5-1/2" 5/64 0 0.058Over 5-1/2" to 6-1/2" 1/8 0 0.070Over 6-1/2" to 8" 5/32 0 0.085

Over 8" to 10" incl. .250 0 .094Over 10" to 12" incl. .375 0 .094Over 12" to 15" incl. .375 0 .109Over 15" to 20" incl. .375 0 .125Over 20" .375 0 .125

ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES.

* 17-4 PH 302-303-304-316-416-440-C “PRECISION GROUND” . . . . . . . . . . . . . . . . . . . . .TOLERANCE +/- .0005"COLD DRAWN HEX’S, SQ’S, IN PH GRADES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DOUBLE SIZE TOLERANCE17-4 PH COLD FINISH FLATS SAME TOLERANCE AS HOT ROLLED FLATS

Size, InchesTolerance

Plus or Minus InchOut-of-Round

Out-of-Roundor Out-ofSquare

Specified SizeInches

Specified Size, in Over Under

Width, Inches

**Sizes are the distances between opposite sides. Round-cornered squares are rolled to dimensions, not to weights per linear foot.

HOT ROLLED ROUND-CORNERED SQUARES

SIZE TOLERANCES

STAINLESS

[email protected]

65FRY STEEL COMPANY

(562) 802-2721

Thickness Tolerance, in. Width Tolerance to 4" incl. Width Tolerance over 4"

1/8" + .010 + .094 + .094- .010 - .031 - .094

3/16" + .050 + .094 + .0941/4" - .010 - .031 - .0945/16"

3/8" + .060 + .094 + .0941/2" - .010 - .031 - .0945/8"

3/4" + .065 + .094 + .094- .010 - .031 - .094

1" + .075 + .094 + .094- .010 + .031 - .094

PROCESSED BAR CUT FROM PLATE(PLATE BAR)

ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES.

NOTE: THE TOLERANCES ARE DIFFERENT THAN TRUE-BAR SO REFERTO THE CHART ABOVE. THE BARS CUT FROM PLATE ARE FROM THEAISI BOOK AND TO SPEC: ASTM-A-484 TABLE 5. THIS IS STANDARD INTHE INDUSTRY FOR THIS PRODUCT.

STAINLESSRecommended Stock Removal**

(Minimum Requirement Necessary To Qualify For Rejection)


[email protected]

(562) 802-2721

NOTE: Product ordered to surface conditions other than ground, turned, or polished should, afterremoval of the standard machining allowance, be free from seams, laps, tears, cracks, andother defects exposed to the machined surfaces.

NOTE: Inspection prior to altering material is advisable.

** NOTE: IT IS NOT ADVISABLE TO TRY TO "FINISH" ON SIZE FROM THE SIZE PURCHASED.

HR-A&P FLATS & SQUARES AND COLD DRAWN FLATSRECOMMENDED MACHINING ALLOWANCES (IN.)

(B)Removal from Thickness

(A) Each Surface Specified Thickness (C)Specified 1/8" to over 1/2" over 1" over 2" over 3" over 4" over 6" Removal from

Width 1/2" incl. to 1" incl. to 2" incl. to 3" incl. to 4" incl. to 6" incl. to 8" incl. Width-Each Surface

Up to 1" Incl. .008 .010 – – – – – – – – – – .015

Over 1"-2" Incl. .012 .015 .031 – – – – – – – – .031

Over 2"-3" Incl. .015 .020 .031 .047 – – – – – – .047

Over 3"-4" Incl. .015 .020 .031 .047 .062 – – – – .062

Over 4"-6" Incl. .015 .020 .031 .047 .062 .093 – – .093

Over 6"-8" Incl. .024 .031 .035 .062 .078 .093 .141 .141

Over 8"-10" Incl. .024 .031 .035 .062 .078 .125 .156 .156

Over 10"-12" Incl. – – – – – – .081 .101 – – – – .172

(A) SELECT THE “WIDTH” FIRST AND THEN READ ACROSS TO SPECIFIED THICKNESS:

(B) SELECT THE READING — THIS IS THE STOCK REMOVAL FOR THE THICKNESS PER SIDE:

(C) CONTINUE ACROSS ON SAME LINE FOR READING FOR WIDTH REMOVAL PER SIDE.

COLD DRAWN: ROUNDS — HEXAGONS — SQUARESUP TO & INCL. 5/16" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .003" PER SIDE EXCEPT 440-C*OVER 5/16". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1% OF DIAMETER PER SIDE*

CENTERLESS GROUND:ALL GROUND BAR SHOULD BE “DEFECT FREE” WITHIN THE STANDARD SIZE TOLERANCESOF ANY MANUFACTURING DEFECTS. IE: SEAMS, LAPS, AND CRACKS.

STOCK REMOVAL IS RECOMMENDED TO BELOW THE STANDARD SIZE TOLERANCES TOREMOVE ANY HANDLING MARKS THAT MAY EXIST.

EXAMPLE:1-1/2" RD TOL IS + OR - .003"MATERIAL SHOULD NOT HAVE ANY DEFECT UNDER -.003"

ROUGH TURNED:ALL “R.T.” SIZES ARE PRODUCED ON THE PLUS SIDE.MATERIAL SHOULD BE DEFECT FREE ON SIZE OF ANY MANUFACTURING DEFECTS.IE: SEAMS, LAPS, AND CRACKS.

EXAMPLE:5" RD HR-RT SHOULD BE DEFECT FREE AT 5"

*FOR 440-C, DOUBLE FIGURES SHOWN, EXCEPT CENTERLESS GROUND AND ROUGH TURN BARS

STAINLESSCHEMICAL ANALYSES – Maximum Unless Indicated


67FRY STEEL COMPANY

(562) 802-2721

PH-13-8MO .05 .10 .10 .01 .008 12.25/13.25 2./2.5 7.5/8.5 Al.90/1.35 N.01 M

15-5 PH .07 1.0 1.0 .03 .015 14./15.5 .50 3.5/5.5 2.5/4.5 Cb 5xC/.45

Ta .05 M

17-4 PH .07 1.0 1.0 .04 .03 15./17.5 .50 3./5. 3./5. Cb 5xC/.45 M

17-7 PH .09 1.0 1.0 .04 .03 16./18. 6.5/7.75 Al .75/1.5 M3Custom 455 .03 .50 .50 .015 .015 11./12.5 .50 7.5/9.5 1.5/2.5 Cb .50 M

Ti .90/1.4 N .015

302 .12 2.0 1.0 .04 .03 17./19. .75. 8./10. .50 N .10 NM

303 S .12 2.0 1.0 .15 .15/.35 17./19. .60 8./10. .50 P+S .18 min NM

303 SE .12 2.0 .70 .12/.17 .04 17./19. .60 8./10. Se .15/.30 NM

304 .08 2.0 1.0 .04 .03 18./20. 1.00 8./10.5 1.00 N .10 NM

304 L .03 2.0 1.0 .04 .03 18./20. 1.00 8./11. 1.00 N .10 NM

309 .08 2.0 1.0 .04 .03 22./24. .75 12./15. .75 NM

310 .08 2.0 .3/.8 .04 .03 24./26. .75 19./22. .75 NM

316 .08 1.25/2. 1.0 .04 .03 16./18. 2./3. 10./14. .50 N .10 NM

316 L .03 1.25/2. 1.0 .04 .03 16./18. 2./3. 10./14. 1.00 N .10 NM

317 .08 2.0 1.0 .045 .03 18./20. 3./4. 11./15. 1.00 N .10 NM

317 L .03 2.0 1.0 .045 .03 18./20. 3./4. 11./15. NM

321 .04/.08 2.0 1.0 .04 .03 17./19. .75 8./12. .75 Ti 5x (C + N)/70 NM

330 .08 2.0 .75/1.5 .03 .03 17./20. .75 34./37. .50 Sn .025 Pb .005 NM

347 .04/.08 2.0 1.0 .04 .03 17./19. .75 9./12. .75 Cb 10xC/1.10

Co 1.0 Ta .05 NM

AM-355 .10/.15 .50/1.25 .50 .04 .03 15./16. 2.5/3.25 4./5. N .07/.13 M

403 .15 1.0 .50 Max .04 .03 11.5/13. .50 .75 .50 M

410 .12/.15 .60 .50 .025 .025 11.5/12.5 .50 .75 .50 Al .05 Sn .05 N .08 M

416 .15 1.25 1.0 .06 .15/.40 11.5/13.5 .60 .75 .50 M

418 (Greek .15/.20 .50 .50 .04 .03 12./14. .50 1.8/2.2 .50 W 2.5/3.5 Sn .50 N .08 M

Ascoloy) Al .15

420 .30/.40 1.0 1.0 .04 .03 12./14. .50 .50 .50 Al .05 Sn .05 M

420 F .30/.40 1.25 1.0 .06 .15/.35 12./14. .60 .50 M

422 .20/.25 .50/1.0 .20/.60 .025 .025 11./12.5 .90/1.25 .50/1.0 .50 V .20/.30 M

W .90/1.25

430 .12 1.0 1.0 .04 .03 16./18. .50 .75 .50 Al .05 Sn .05 M

430 F .12 1.25 1.0 .06 .15 min 14./18. .60 M

431 .13/.17 .30/.80 .20/.60 .04 .03 15.5/16.5. .25 1.25/2.5 .50 N .10 M

440 A .60/.75 1.0 1.0 .04 .03 16./18. .75 .75 .50 M

440 C .95/1.2 1.0 1.0 .02 .01 16./18. .40/.65 .75 .50 M

440 F Se .95/1.2 1.25 1.0 .04 .03 16./18. .40/.60 .50 .60 Sn .05 N .08 Se .15/.25 M

446 .20 1.5 1.0 .04 .03 23./27. N .25 M1Nitronic 40 .04 8./10. 1.0 .045 .03 19./21.5 .75 5.5/7.5 .75 N .15/.40 NM1Nitronic 50 .06 4./6. 1.0 .04 .03 20.5/23.5 1.5/3.0 11.5/13.5 N .20/.40 Cb .10/.30 Al .02

V .10/.30 Ti .02 Zr .02 NM1Nitronic 60 .10 7./9. 3.5/4.5 16./18. 8.0/9.0 N .08/.18 NM3Fry Alloy 20 .07 2.0 1.0 .045 .035 19./21. 2./3. 32./38. 3./4. Cb + Ta 8xC Min/

1.0 Max NM

MAN- PHOS- MOLYB-TYPE CARBON GANESE SILICON PHORUS SULFER CHROME DENUM NICKEL COPPER OTHERS

M – MagneticNM – Non-magnetic

3 Trademark Carpenter Technology1 Trademark

Carbon = C Phosphorus = P Molybdenum = Mo Aluminum = AlManganese = Mn Sulfur = S Nickel = Ni Nitrogen = NSilicon = Si Chromium = Cr Copper = Cu Columbium = CbTantalum = Ta Titanium = Ti Lead = Pb Selenium = SeTin = Sn Cobalt = Co Tungsten = W Vanadium = VZirconium = Zr

STAINLESSMACHINABILITY RATINGS


[email protected]

(562) 802-2721

302 70 40302/304/304 L “B” 55 28303 150 75303 “B” 80 43304 70 40304 L 70 40309 60 36310 60 36316 60 36316/316 L “B” 50 22316 L 60 36317/317 L 60 36321 60 36330 45 20347 60 36403 95 54410 95 54416 Ann 150 75416 H.T. 85 50418 (Greek Ascoloy) 96 50420 85 50420 F 125 68422 85 50430 110 66430 F 150 75431 80 48440 A 65 40440 C 65 40440 F Se 80 48446 60 363Custom 455 (12-9-2) 55 28PH 13-8 MO 60 3615-5 PH 75 4517-4 PH 75 4517-4 PH “H1150” 85 5017-7 PH 75 45AM 355 72 421Nitronic 40 50 221Nitronic 50 50 221Nitronic 60 50 223Fry Alloy 20 70 40

APPROXIMATE SURF. FT.PER MIN.

GRADE % RELATIVE SPEEDBASED ON C-1212 as 100%

These machinability ratios are based on high speed tooling and must be recognized as approximatevalues.

3 Trademark Carpenter Technology1 Trademark

SU

PE

RA

LLOY

AN

DE

LEC

TR

ICA

L ST

EE

L

SU

PE

RA

LLO

YA

ND

ELE

CT

RIC

AL

ST

EE

L

SUPER ALLOYAND

ELECTRICAL STEELGRADES STOCKED


[email protected]

(562) 802-2721

AUTOMATIC EXCEPTIONS TO THE SPECS LISTED ARE: LINE MARKING AND INSPECTION (I.E. MAG., SONIC, ETC.)2 Trademark United Technology 3 Trademark Carpenter Technology 4Trademark SPS Technology

ELECTRICAL STEELS


A-286 AGE HARD (1650° SOL. TREATED)AMS-5737, ASTM-A-638 GR. 660TYPE 1, ASTM-A-453 GR. 660 CL. A

A-286 AGE HARD (1800° SOL. TREATED)AMS-5732 (SUPERSEDES AMS-5735),ASTM-A-638 GR. 660 TYPE 2, ASTM-A-453 GR. 660 CL. B

A-286 SOL. TREATED AMS-5731 (SUPERSEDES AMS-5736)CAP. OF AMS-5732, MS-301, HI-SHEAR#140 TYPE 3 (CHEMS ONLY)

A-286 (CAP. 160 KSI) CHEMS ONLY TO FOLLOWING: AMS-“COLD REDUCED” 5731, AMS-5732, AMS-5734, AMS-5736,

AMS-5737, AMS-5853, SPS-M-118(CHECK TRS), HI-SHEAR #140 TYPE 1

A-286 (CAP. 210 KSI) AMS-5726, SPS-M-250 (CHECK TRS),“COLD REDUCED” CHEMS ONLY TO FOLLOWING:

AMS-5731, AMS-5732, AMS-5734,AMS-5736, AMS-5737, HI- SHEAR#140 TYPE 2

NICKEL “200” ASTM-B-160

NICKEL “400” AMS-4675 (CHEMS ONLY), QQN-281CL. A, ASTM-B-164

NICKEL “405” AMS-4674, QQN-281 CL. B, ASTM-B-164 CL. B, ASME-B-164 CL. B

NICKEL “K-500” AMS-4676 CHEMS ONLY, QQN-286SOL. TR. FORM 1 REV E ONLY (H.F. ANN. &

UNAGED)

NICKEL “K-500” AMS-4676 CHEMS ONLY, QQN-286SOL. TR. & AGED FORM 2 REV E ONLY (H.F. ANN. &

AGED)

NICKEL “600” AMS-5665 (CHEMS ONLY), ASTM-B-166(CHEMS ONLY), MIL-N-6710 AMD. 2 (EXC. MAX. TENS.)

NICKEL “625” AMS-5666, ASTM-B-446 GRD. 1

NICKEL “800” ASTM-B-408, ASME-B-408 (CHEMS ONLY BOTH SPECS)

NICKEL “800 H” ASTM-B-408, ASME-B-408

NICKEL “800 HT” ASTM-B-408, ASME-B-408

NICKEL “825” ASTM-B-425, ASME-B-425


718 VAC. MELT. AMS-5662, ASTM-B-637, ASME-SB-637, CAP. OF AMS-5663, B50TF15 CL. D, SPS-M-275 (CHEMS ONLY), C50TF13 (CHEMS ONLY), B50T69A, HI-SHEAR #156 (CHEMS ONLY),EN 2404 (UNDER 4" ROUND ONLY)

718 VAC. MELT. AMS-5962, SPS-M-637, CHEMS ONLY(CAP. 220 KSI) TO FOLLOWING: AMS-5662, B50TF“COLD REDUCED” 15, HI SHEAR #156, C50TF13, VMS-

110, AIC-MS-110. DMS-2209

X-750 AMS-5667, B50YP44B1 (EXC. HARD-NESS)

L-605 VAC. MELT. AMS-5759

MARAGING “300” AMS-6514, MIL-S-46850 TYPE 4 (EXC.PARA. 3.5.3), LBO-160-164, MBO-160-006 (EXC. SONIC), HMS-6-1404

2 WASPALOY AMS-5708TYPE 2, CAP. OF AMS-5709“HEADING QUALITY”

2 WASPALOY AMS-5708 & AMS-5709 (CHEMS ONLY“COLD REDUCED” BOTH SPECS), EXC. HARDNESS TO

FOLLOWING: SPS-M-175, VSM-1333,VMS-112, Voi-Shan-S-71001

4MP 35N AMS-5844, CAP. OF AMS 5845, SPS-M-646

4MP 159 AMS-5842, CAP. OF AMS-5843

FRY ALLOY X AMS-5754

FRY ALLOY C AMS-5750, ASTM-B-574, ASME-B-574

3AERMET 100 AMS-6532, AMS-2300, MIL-S-2154 TYPE1 CLASS A, MMS-217 (EXC.TRANS.IMPACT)

INVAR 36 “FM” MIL-S-16598 & MBO-160-151 (CHEMSONLY BOTH SPECS)

3KOVAR AMS-7727, ASTM-F-15, MIL-I-23011CL. 1, AMS-I-23011 CL. 1

4750 AMS-7718 EXC. HARDNESS, CAP. OFMIL-N-14411 COMP. 3, ABO-170- 014

SUPER ALLOYAND

ELECTRICAL STEEL

ROUNDSSTOCKED IN 12' R/L


71FRY STEEL COMPANY

(562) 802-2721

SIZE TYPE FINISH. SIZE TYPE FINISH.

.270" 718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.MP 35N C.G.MP 159 C.G.

9/32" A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.

.290" 718 V.M. C.R. (Cap. 220 KSI) C.G.

19/64" A-286 C.R (Cap. 210 KSI) C.G.718 V.M. C.G.

5/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.Waspaloy H.Q. C.G.Fry Alloy X C.G.INVAR 36 “FM” C.G.4750 C.G.

.3175" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.3225" A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.MP 35N C.G.

.328" Waspaloy C.R. C.G.

.3325" MP 159 C.G.

21/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.Waspaloy H.Q. C.G.

11/32" A-286 C.R. (Cap. 160 KSI) C.G.718 V.M. C.G.

.352" 718 V.M. C.R. (Cap. 220 KSI) C.G.


3/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “600” C.G.

1/8" INVAR-36 “FM” C.G.Fry Alloy X C.G.

3/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “600” C.G.718 V.M. C.G.X-750 C.G.Waspaloy H.Q. C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.4750 C.G.

.1925" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.1975" A-286 Sol. Tr. C.G.

13/64" 718 V.M. C.G.

.205" L-605 C.G.

7/32" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Waspaloy H.Q. C.G.


15/64" 718 V.M. C.G.

1/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Waspaloy H.Q. C.G.Fry Alloy X C.G.Fry Alloy C C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

.255" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.260" A-286 Aged (1650°) C.G.A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap.. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.

17/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M C.G.

Finish: C.D. – Cold Drawn Condition: Ann. – Annealed ESR – Electroslag Re-melt V.M. – Vacuum Arc Re-meltC.F. – Cold Finish Sol trt – Solution Treated Sel – Selenium C.R. – Cold ReducedC.G. – Centerless Ground H.T. – Heat treated (RC 26/32) “B” – Hi Tensile L – Low CarbonR.T. – Rough Turned S – Sulfer “FM” – Free MachiningH.F. - Hot Finished H.Q. – Heading Quality S.R. – Stress Relieved

SUPER ALLOYAND

ELECTRICAL STEEL



[email protected]

(562) 802-2721



SIZE TYPE FINISH SIZE TYPE FINISH


29/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.Waspaloy H.Q. C.G.


31/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.MP 35N C.G.MP 159 C.G.

1/2" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800”H C.G.Nickel “800”HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

.505" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.510" A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.


.524" Waspaloy H.Q. C.G.Waspaloy C.R. C.G.

.525" 718 V.M. C.R. (Cap. 220 KSI) C.G.MP 35N C.G.


.535" A-286 C.R. (Cap. 160 KSI) C.G.MP 159 C.G.

3/8" Nickel “625” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Waspaloy H.Q. C.G.Fry Alloy X C.G.Fry Alloy C C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

.380" A-286 Aged (1650°) C.G.

.385" A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.

25/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.MP 35N C.G.

.400" MP 159 C.G.


27/64" 718 V.M. C.G.

7/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.G.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Waspaloy H.Q. C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.4750 C.G.

.4425" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.4475" A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.

SUPER ALLOYAND

ELECTRICAL STEEL



73FRY STEEL COMPANY

(562) 802-2721


.635" A-286 Sol. Tr. C.G.A-286 C.R (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.Aermet 100 C.G.



.649" 718 V.M. C.R. (Cap. 220 KSI) C.G.MP 35N C.G.MP 159 C.G.

21/32" A-286 C.R. (Cap. 160 KSI) C.G.718 V.M . C.G.


11/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 160 KSI) C.G.Nickel “200” C.G.Nickel “625” C.G.718 V.M. C.G.INVAR-36 “FM” C.G.

.6925" A-286 Aged (1800°) C.G.718 V.M. C.G.

45/64" 718 V.M. C.G.


47/64" 718 V.M. C.G.

3/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.GNickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.



9/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.

.5675" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.5725" A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.

.5775" A-286 C.R. (Cap. 160 KSI) C.G.

37/64" 718 V.M. C.G.

.587" 718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.MP 35N C.G.MP 159 C.G.


39/64" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M C.G.

5/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800”H C.G.Nickel “800”HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

.630" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.


SUPER ALLOYAND

ELECTRICAL STEEL



[email protected]

(562) 802-2721




.880" A-286 Aged (1650°) C.G.

.885" A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Maraging “300” C.G.Waspaloy H.Q. C.G.Waspaloy C.R. C.G.Aermet 100 C.G.

.890" A-286 C.R. (Cap. 160 KSI) C.G.

.900" 718 V.M. C.R. (Cap. 220 KSI) C.G.MP 35N C.G.MP 159 C.G.

29/32" A-286 C.R. (Cap. 210 KSI) C.G.

15/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. C.G.718 V.M. C.G.INVAR-36 “FM” C.G.

1" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Waspaloy H.Q. C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR 36 “FM” C.G.Kovar C.G.4750 C.G.Aermet 100 C.G.

1.005" A-286 Aged (1650°) C.G.

1.010" A-286 Sol. Tr. C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.

1.020" A-286 C.R. (Cap. 160 KSI) C.G.

1.022" 718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.MP 35N C.G.

1.025" MP159 C.G.

3/4" 4750 C.G.

.755" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.

.760" A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.L-605 C.G.Waspaloy H.Q. C.G.Aermet 100 C.G.


49/64" A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.

.774" MP 35N C.G.MP 159 C.G.

.775" 718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.


.785" A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.

.790" 718 V.M. C.R. (Cap. 220 KSI) C.G.

13/16" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “600” C.G.718 V.M. C.G.INVAR-36 “FM” C.G.4750 C.G.

7/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nlckel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

SUPER ALLOYAND

ELECTRICAL STEEL



75FRY STEEL COMPANY

(562) 802-2721


1.260" A-286 C.R. (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.

1.270" 718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.

1.279" MP 35N C.G.MP159 C.G.

1-5/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-3/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

1.385" A-286 C.R. (Cap. 210 KSI) C.G.

1.390" 718 V.M. C.R. (Cap. 220 KSI) C.G.MP 35N C.G.MP 135 C.G.Waspaloy H.Q. C.G.

1-7/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-1/2" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Waspaloy H.Q. C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.

1-1/16" A-286 Aged (1650°) C.G.718 V.M. C.G.INVAR-36 “FM” C.G.L-605 C.G.

1-1/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

1.135" A-286 C,R, (Cap. 160 KSI) C.G.A-286 C.R. (Cap. 210 KSI) C.G.Nickel “625” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.Waspaloy H.Q. C.G.

1.147" 718 V.M. C.R. (Cap. 220 KSI) C.G.

1.155" MP 35N C.G.MP159 C.G.

1-3/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-1/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol Tr. C.G. Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.GMaraging “300” C.G.Waspaloy H.Q. C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G


SUPER ALLOYAND

ELECTRICAL STEEL



[email protected]

(562) 802-2721




2" Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.Aermet 100 C.G.

2-1/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

2-1/8" A-286 Aged (1650°) C.G.Nickel “400” C.D.-S.R.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.

2-1/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Aermet 100 C.G.

2-3/8" A-286 Aged (1650°) C.G.Nickel “400” C.D.-S.R.Nickel “625” C.G.718 V.M. C.G.L-605 C.G.

2-1/2" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.G.

1-1/2" Kovar C.G.4750 C.G.Aermet 100 C.G.

1.510" A-286 C.R. (Cap. 210 KSI) C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.

1.520" MP35N C.G.

1-9/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-5/8" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “625” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

1-11/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-3/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Nickel “200” C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.

1-13/16" A-286 Aged (1650°) C.G.718 V.M. C.G.

1-7/8" A-286 Aged (1650°) C.G.718 V.M. C.G.718 V.M. C.R. (Cap. 220 KSI) C.G.X-750 C.G.INVAR-36 “FM” C.G.4750 C.G.Maraging “300” C.G.

2" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.

SUPER ALLOYAND

ELECTRICAL STEEL



77FRY STEEL COMPANY

(562) 802-2721


3" Maraging “300” C.G.Aermet 100 R.T.

3-1/8" A-286 Aged (1650°) C.G.

3-1/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “600” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.718 V.M R.T.X-750 R.T.Maraging “300” C.G.Fry Alloy X C.G.

3-3/8" A-286 Aged (1650°) C.G.

3-1/2" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.718 V.M. R.T.X-750 R.T.L-605 C.G.Maraging “300” C.G.Fry Alloy C R.T.Fry Alloy X C.G.INVAR-36 “FM” C.G.4750 C.G.Aermet 100 R.T.

3-5/8" A-286 Aged (1650°) R.T.

3-3/4" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.Nickel “400” C.D.-S.R.Nickel “625” R.T.718 V.M. R.T.Maraging “300” C.G.Fry Alloy X R.T.

3-7/8" 718 V.M. R.T.

4" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.A-286 Sol. Tr. R.T.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Nickel “600” R.T.Nickel “625” R.T.Nickel “800” R.T.Nickel “800” H R.T.Nickel “800” HT R.T.718 V.M. R.T.X-750 R.T.L-605 C.G.

2-1/2" Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.INVAR-36 “FM” C.G.Kovar C.G.4750 C.G.Aermet 100 C.G.

2-5/8" A-286 Aged (1650°) C.G.Nickel “400” C.D.-S.R.Nickel “625” C.G.718 V.M. C.G.Fry Alloy X C.G.

2-3/4" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.Nickel “400” C.D.-S.R.Nickel “K-500” Ann. H.F.-C.GNickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.718 V.M. C.G.X-750 C.G.L-605 C.G.Maraging “300” C.G.Fry Alloy C C.G.Fry Alloy X C.G.Aermet 100 C.G.

2-7/8" A-286 Aged (1650°) C.G.A-286 Sol. Tr. C.G.

3" A-286 Aged (1650°) C.G.A-286 Aged (1800°) C.G.A-286 Sol. Tr. C.G.Fry Alloy C C.G.Fry Alloy X C.G.L-605 C.G.4750 C.G.INVAR-36 “FM” C.G.Nickel “400” C.D.-S.R.Nickel “405” C.G.Nickel “K-500” Ann. H.F.-C.G.Nickel “K-500” Ann. & Aged H.F.-C.G.Nickel “600” C.G.Nickel “625” C.G.Nickel “800” C.G.Nickel “800” H C.G.Nickel “800” HT C.G.Nickel “825” C.G.718 V.M. C.G.


SUPER ALLOYAND

ELECTRICAL STEEL



[email protected]

(562) 802-2721




6" Nickel “600” R.T.Nickel “625” R.T.718 V.M. R.T.Maraging “300” R.T.X-750 R.T.Fry Alloy X R.T.INVAR-36 “FM” R.T.Aermet 100 R.T.

6-1/4" A-286 Aged (1650°) R.T.

6-1/2" A-286 Aged (1650°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Fry Alloy X R.T.

7" A-286 Aged (1650°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.718 V.M. R.T.Fry Alloy X R.T.

7-1/2" A-286 Aged (1650°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.

8" A-286 Aged (1650°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “625” R.T.718 V.M. R.T.

8-1/2" A-286 Aged (1650°) R.T.

9" A-286 Aged (1650°) R.T.718 V.M. R.T.

9-1/2" A-286 Aged (1650°) R.T.

10" A-286 Aged (1650°) R.T.718 V.M. R.T.

11" A-286 Aged (1650°) R.T.718 V.M. R.T.

12" A-286 Aged (1650) R.T.718 V.M. R.T.

4" Maraging “300” R.T.Fry Alloy C R.T.Fry Alloy X R.T.INVAR-36 “FM” C.G.4750 C.G.Aermet 100 R.T.

4-1/8" A-286 Aged (1650°) R.T.

4-1/4" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.718 V.M. R.T.Fry Alloy X R.T.

4-1/2" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Nickel “600” R.T.Nickel “625” R.T.718 V.M. R.T.X-750 R.T.Maraging “300” R.T.Fry Alloy X R.T.Aermet 100 R.T.

4-3/4" A-286 Aged (1650°) R.T.718 V.M. R.T.Fry Alloy X R.T.

5" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Nickel “600” R.T.Nickel “625” R.T.718 V.M. R.T.X-750 R.T.Maraging “300” R.T.Fry Alloy X R.T.INVAR-36 “FM” R.T.Aermet 100 R.T.

5-1/4" A-286 Aged (1650°) R.T.Fry Alloy X R.T.

5-1/2" A-286 Aged (1650°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.Nickel “625” R.T.718 V.M. R.T. Maraging “300” R.T.Fry Alloy X R.T.Aermet 100 R.T.

5-3/4" A-286 Aged (1650°) R.T.Fry Alloy X R.T.

6" A-286 Aged (1650°) R.T.A-286 Aged (1800°) R.T.Nickel “400” H.R.-S.R.Nickel “K-500” Ann. H.F.-R.T.Nickel “K-500” Ann. & Aged H.F.-R.T.

SUPER ALLOYAND

ELECTRICAL STEEL

HEXAGONSSTOCKED IN 12' R/L


79FRY STEEL COMPANY

(562) 802-2721


13/16" A-286 Aged (1650°) C.D.

7/8" A-286 Aged (1650°) C.D.A-286 Aged (1800°) C.D.A-286 C.R. (Cap. 160 KSI) C.D.

15/16" A-286 Aged (1650°) C.D.A-286 C.R. (Cap. 160 KSI) C.D.

1" A-286 Aged (1650°) C.D.A-286 Aged (1800°) C.D.A-286 C.R. (Cap. 160 KSI) C.D.

1-1/16" A-286 Aged (1650°) C.D.A-286 C.R. (Cap. 160 KSI) C.D.

1-1/8" A-286 Aged (1650°) C.D.

1-1/4" A-286 Aged (1650°) C.D.

1-5/16" A-286 Aged (1650°) C.D.

1-3/8" A-286 Aged (1650°) C.D.

1-7/16" A-286 Aged (1650°) C.D.

1-1/2" A-286 Aged (1650°) C.D.

1/4" A-286 Aged (1800°) C.D.

5/16" A-286 Aged (1650°) C.D.A-286 Aged (1800°) C.D.


7/16 " A-286 Aged (1650°) C.D.A-286 Aged (1800°) C.D.A-286 C.R. (Cap. 160 KSI) C.D.




11/16" A-286 Aged (1650°) C.D.



SUPER ALLOYAND

ELECTRICAL STEEL

FLATS AND SQUARESSTOCKED IN 12' R/L


[email protected]

(562) 802-2721




SQUARES

1/2" A-286 Aged (1650°) C.D.

5/8" A-286 Aged (1650°) C.D.

3/4" A-286 Aged (1650°) C.D.

1" A-286 Aged (1650°) C.D.

1-1/4" A-286 Aged (1650°) H.R.

1-1/2" A-286 Aged (1650°) H.R.

2" A-286 Aged (1650°) H.R.

2-1/2" A-286 Aged (1650°) H.R.

3" A-286 Aged (1650°) H.R.

FLATS

1/2" x 1" A-286 Aged (1650°) H.R.718 V.M. H.R.

1/2" x 1-1/2" A-286 Aged (1650°) H.R.718 V.M. H.R.

1/2" x 2" A-286 Aged (1650°) H.R.718 V.M. H.R.

3/4" x 1" A-286 Aged (1650°) H.R.

3/4" x 1-1/2" 718 V.M. H.R.

3/4" x 2" A-286 Aged (1650°) H.R.718 V.M. H.R.

3/4" x 4" 718 V.M. H.R.

1" x 1-1/2 " A-286 Aged (1650°) H.R.

1" x 2" A-286 Aged (1650°) H.R.718 V.M. H.R.

1" x 2-1/2" A-286 Aged (1650°) H.R.

1" x 3" A-286 Aged (1650°) H.R.718 V.M. H.R.

1" x 4" 718 V.M. H.R.

1-1/2" x 2" A-286 Aged (1650°) H.R.

1-1/2" x 3" A-286 Aged (1650°) H.R.

2" x 3" A-286 Aged (1650°) H.R.

3" x 4" A-286 Aged (1650°) H.R.

SUPER ALLOYAND

ELECTRICAL STEEL

WEIGHTS


81FRY STEEL COMPANY

(562) 802-2721

Weights for Nickel 200, 400,405, Fry Alloy C

Size WT/FT WT/Bar

Weights for L-605

Size WT/FT WT/Bar

.205" .13 1.5601/4" .207 2.484.260" .209 2.508.3225" .320 3.8403/8" .437 5.246.385" .459 5.5087/16" .610 7.320.4475" .620 7.4401/2" .778 9.336.510" .806 9.6725/8" 1.210 14.520.635" 1.250 15.0003/4" 1.750 21.000.760" 1.790 21.4807/8" 2.370 28.440.885" 2.430 29.1601" 3.100 37.2001-1/4" 4.840 58.0801-3/8" 5.880 70.5601-1/2" 6.980 83.7601-5/8" 8.213 98.5561-3/4" 9.526 114.3122" 12.440 149.280

1/4" .19 2.2805/16" .294 3.5283/8" .426 5.1127/16" .576 6.9131/2" .755 9.0609/16" .9558 11.4705/8" 1.180 14.16011/16" 1.427 17.1243/4" 1.700 20.40013/16" 1.994 23.9287/8" 2.310 27.7201" 3.020 36.2401-1/8" 3.822 45.8641-1/4" 4.720 56.6401-3/8" 5.710 68.5201-1/2" 6.790 81.4801-5/8" 7.975 95.7001-3/4" 9.207 110.4902" 12.080 144.9602-1/8" 13.600 163.2002-1/4" 15.240 182.8802-3/8" 16.980 203.7602-1/2" 18.790 225.4802-5/8" 20.740 248.8802-3/4" 22.740 272.8803" 27.100 325.2003-1/4" 31.760 381.1203-1/2" 36.830 441.9603-3/4" 42.330 507.9604" 48.100 577.2004-1/2" 60.960 731.5205" 75.250 903.0005-1/2" 90.950 1091.4006" 108.200 1298.4006-1/2" 127.100 1525.2007" 147.320 1767.8407-1/2" 169.120 2029.4408" 192.400 2308.800

Weights4MP 35N, 4MP159

Size WT/FT WT/Bar

.270" .209 2.508

.3225" .298 3.57625/64" .438 5.256.400" .454 5.44831/64" .671 8.052.525" .790 9.480.535" .812 9.744.587" .987 11.844.649" 1.210 14.520.774" 1.716 20.592.900" 2.320 27.8401.022" 2.990 35.8801.025" 2.980 35.7601.155" 3.770 45.2401.279" 4.620 55.4401.390" 5.540 66.4801.520" 6.620 79.440

4 Trademark SPS Technology

SUPER ALLOYAND

ELECTRICAL STEEL

WEIGHTS


[email protected]

(562) 802-2721

3/16" .101 1.2181/4" .180 2.164.260" .194 2.3325/16" .281 3.380.3225" .299 3.5883/8" .405 4.867.385" .426 5.1127/16" .552 6.624.4475" .556 6.6771/2" .721 8.652.510" .747 8.9729/16" .840 10.560.5725" .942 11.3105/8" 1.127 13.524.635" 1.159 13.90811/16" 1.310 15.7203/4" 1.622 19.464.760" 1.660 19.92013/16" 1.900 22.8007/8" 2.208 26.496.885" 2.250 27.0001" 2.884 34.6081.010" 2.930 35.1601-1/8" 3.620 43.4401.135" 3.700 44.4001-1/4" 4.506 54.0721.260" 4.560 54.7201-3/8" 5.200 62.4001-1/2" 6.489 77.8681-5/8" 7.330 87.9601-3/4" 8.830 105.9602" 11.540 138.4802-1/4" 15.230 182.7602-1/2" 18.030 216.3602-3/4" 21.810 261.7203" 25.960 311.5203-1/4" 30.520 366.2403-1/2" 35.330 423.9603-3/4" 39.050 468.6004" 46.150 553.8004-1/2" 58.520 702.2405" 72.250 867.0006" 103.900 1246.8006-1/2" 121.850 1462.2007" 141.320 1695.8407-1/2" 162.220 1946.6408" 184.580 2214.960

1/2" .676 8.1175/8" 1.056 12.6793/4" 1.521 18.2597/8" 2.071 24.8521" 2.705 32.4601-1/8" 3.423 41.0761-1/4" 4.227 50.7241-3/8" 5.114 61.3681-1/2" 6.086 73.0321-3/4" 8.284 99.4082" 10.820 129.8402-1/4" 13.690 164.2802-1/2" 16.910 202.9202-3/4" 20.460 245.5203" 24.340 292.0803-1/4" 28.570 342.8403-1/2" 33.140 397.6804" 43.280 519.3604-1/2" 54.380 652.5605" 67.170 806.0405-1/2" 81.260 975.1206" 96.700 1160.400

Weights800, 800H, 800HT,

3Aermet 100

Size WT/FT WT/Bar

Weights for Nickel 500, 600, 625

Size WT/FT WT/Bar

Weights for 718

Size WT/FT WT/Bar

3 Trademark Carpenter Technology

1/2" x 1" 1.770 21.2401/2" x 1-1/2" 2.650 31.8001/2" x 2" 3.540 42.4803/4" x 1-1/2" 3.980 47.7603/4" x 2" 5.310 63.7203/4" x 4" 10.610 127.3201" x 2" 7.070 84.8401" x 3" 10.610 127.3201" x 4" 14.150 169.800

SUPER ALLOYAND

ELECTRICAL STEEL

WEIGHTS


83FRY STEEL COMPANY

(562) 802-2721

25/32" 1.690 20.280.790" 1.740 20.88013/16" 1.830 21.9607/8" 2.120 25.440.885" 2.180 26.156.900" 2.260 27.12015/16" 2.440 29.2801" 2.790 33.4801.010" 2.800 33.6001.022" 2.890 34.6801-1/16" 3.134 37.6081-1/8" 3.540 42.4801.135" 3.578 42.9361.147" 3.680 44.1601-3/16" 3.920 47.0401-1/4" 4.360 52.3201.260" 4.400 52.8001.270" 4.500 54.0001-5/16" 4.784 57.4081-3/8" 5.300 63.6001.390" 5.383 64.5961-7/16" 5.738 68.8561-1/2" 6.270 75.2401.510" 6.420 77.0401-9/16" 6.850 82.2001-5/8" 7.330 87.9601-11/16" 7.900 94.8001-3/4" 8.540 102.4801-13/16" 9.124 109.4881-7/8" 9.760 117.1202" 11.160 133.9202-1/16" 11.814 141.7682-1/8" 12.610 151.3202-1/4" 14.130 169.5602-3/8" 15.660 187.9202-1/2" 17.400 208.8002-5/8" 19.180 230.1602-3/4" 21.000 252.0003" 25.000 300.0003-1/4" 29.340 352.0803-1/2" 34.200 410.4003-3/4" 39.190 470.2804" 44.600 535.2004-1/4" 50.600 607.2004-1/2" 56.240 674.8804-3/4" 63.200 758.4005" 69.600 835.2005-1/4" 77.200 926.4005-1/2" 84.700 1016.4005-3/4" 92.600 1111.2006" 100.200 1202.4006-1/2" 117.900 1414.8007" 136.000 1632.0008" 178.000 2136.0009" 216.500 2598.00010" 278.000 3336.00011" 343.000 4116.00012" 398.000 4776.000

Weights For 718,X-750, 2WASPALOY,FRY ALLOY X, 825

Size WT/FT WT/Bar

Weights For 718,X-750, 2WASPALOY,FRY ALLOY X, 825

Size WT/FT WT/Bar

2 Trademark United Technology

1/8" .0442 .5303/16" .098 1.17613/64" .114 1.3687/32" .133 1.60015/64" .153 1.8361/4" .170 2.040.260" .188 2.25617/64" .195 2.340.270" .202 2.4249/32" .218 2.616.290" .235 2.82019/64" .244 2.9285/16" .271 3.252.3225" .289 3.45621/64" .300 3.60011/32" .332 3.984.352" .3457 4.14823/64" .359 4.3083/8" .379 4.548.380" .385 4.620.385" .411 4.93225/64" .424 5.08813/32" .457 5.48427/64" .494 5.9287/16" .531 6.372.4475" .556 6.67729/64" .570 6.84015/32" .607 7.28431/64" .651 7.8121/2" .707 8.484.510" .722 8.66433/64" .738 8.856.524" .763 9.156.525" .769 9.22817/32" .781 9.372.540" .813 9.75635/64" .833 9.9969/16" .879 10.548.5725" .900 10.80037/64" .928 11.136.587" .960 11.52019/32" .975 11.70039/64" 1.030 12.3605/8" 1.090 13.080.635" 1.120 13.44041/64" 1.140 13.680.645" 1.150 13.800.649" 1.180 14.16021/32" 1.190 14.28043/64" 1.253 15.03611/16" 1.310 15.72045/64" 1.370 16.44023/32" 1.429 17.14847/64" 1.500 18.0003/4" 1.570 18.840.760" 1.600 19.20049/64" 1.627 19.524.775" 1.670 20.040

SUPER ALLOYAND

ELECTRICAL STEEL

WEIGHTS


[email protected]

(562) 802-2721

Weights for Kovar

Size WT/FT WT/Bar

WeightsINVAR 36 “FM”,MARAGING 300

Size WT/FT WT/Bar

3/16" .100 1.2001/4" .180 2.1605/16" .270 3.2403/8" .410 4.9207/16" .550 6.6001/2" .720 8.6405/8" 1.130 13.5603/4" 1.620 19.44013/16" 1.930 23.1607/8" 2.210 26.5201" 2.920 35.0401-1/8" 3.650 43.8001-1/4" 4.520 54.2401-3/8" 5.470 65.6401-1/2" 6.560 78.7201-5/8" 7.640 91.6801-3/4" 8.850 106.2001-7/8" 10.170 122.0402" 11.560 138.7202-1/2" 18.080 216.9603" 27.910 334.9203-1/2" 34.060 408.7204" 44.500 534.000

Weights for 4750

Size WT/FT WT/Bar

1/4" .170 2.0403/8" .399 4.7881/2" .711 8.5325/8" 1.110 13.3203/4" 1.600 19.2007/8" 2.179 26.1481" 2.845 34.1401-1/8" 3.600 43.2001-1/4" 4.440 53.2801-3/8" 5.380 64.5601-1/2" 6.400 76.8001-5/8" 7.520 90.2401-3/4" 8.710 104.5202" 11.380 136.5602-1/2" 17.780 213.360

1/8" .043 .5223/16" .100 1.2001/4" .170 2.0405/16" .270 3.2403/8" .390 4.6807/16" .520 6.2401/2" .690 8.2805/8" 1.070 12.84011/16" 1.296 15.5553/4" 1.540 18.48013/16" 1.810 21.7207/8" 2.100 25.200.885" 2.150 25.80015/16" 2.410 28.9201" 2.740 32.8801-1/16" 3.090 37.0801-1/8" 3.470 41.6401-1/4" 4.290 51.4801-3/8" 5.190 62.2801-1/2" 6.170 74.0201-5/8" 7.240 86.8801-3/4" 8.400 100.8001-7/8" 9.640 115.6802" 10.970 131.6402-1/4" 13.890 166.6802-1/2" 17.400 208.8002-3/4" 20.200 242.4003" 24.650 295.8003-1/4" 28.210 338.5203-1/2" 33.590 403.0803-3/4" 37.600 451.2004" 43.890 526.6804-1/2" 54.000 648.0005" 69.400 832.8005-1/2" 80.800 969.6006" 98.500 1182.000

NOTE: For A-286 Weights refer to pages57 through 63 of Stainless Section

3 Trademark Carpenter Technology

3

SUPER ALLOYAND

ELECTRICAL STEEL

SIZE TOLERANCES*


85FRY STEEL COMPANY

(562) 802-2721

TolerancePlus or Minus Out-of-Round

Inch

1/16" to 9/32" .001" .001"5/16" to 11/32" .0015" .0015"3/8" to 15/32" .0015" .0015"

1/2" to 19/32" .002" .002"5/8" to 31/32" .002" .002"1" to 1-15/32" .0025" .0025"

1-1/2" to 2-3/4" .003" .003"2-13/16" to 3" .003" .003"3-1/8" to 4" .003" .003"

Size ToleranceIn. Over Under

Over 1-1/2" to 2" incl. .016 .016Over 2" to 2-1/2" incl. .031 0Over 2-1/2" to 3-1/2" incl. .047 0Over 3-1/2" to 4-1/2" incl. .062 0Over 4-1/2" to 5-1/2" incl. .078 0Over 5-1/2" to 6-1/2" incl. .125 0Over 6-1/2" to 8" incl. .156 0Over 8" to 10" incl. .250 0Over 10" .375 0

Size, Inches

COLD DRAWN OR

CENTERLESS GROUND BARS

Up to 1" 0.008 0.010 - - - 0.015 0.015incl.

Over 1" to 0.012 0.015 0.031 - - 0.031 0.0312" incl.

Over 2" to 0.015 0.020 0.031 0.062 0.031 0.062 0.0314" incl.

Over 4" to 0.015 0.020 0.031 0.062 0.031 0.093 0.0626" incl.

Over 6" to 0.016 0.025 0.031 0.062 0.031 0.125 0.1568" incl.

Over 8" to 0.021 0.031 0.031 0.062 0.031 0.156 0.15610" incl.

HOT ROLLED BARS – FLATS

STAINLESSHOT FINISHED ROUNDS AND SQUARES

Out-of-RoundSpecified Size, in Over Under or

Out-of-Square

Over 5/16" to 7/16" 0.006 0.006 0.009Over 7/16" to 5/8" 0.007 0.007 0.010Over 5/8" to 7/8" 0.008 0.008 0.012Over 7/8" to 1" 0.009 0.009 0.013Over 1" to 1-1/8" 0.010 0.010 0.015

Over 1-1/8" to 1-1/4" 0.011 0.011 0.016Over 1-1/4" to 1-3/8" 0.012 0.012 0.018Over 1-3/8" to 1-1/2" 0.014 0.014 0.021Over 1-1/2" to 2" 1/64 1/64 0.023Over 2" to 2-1/2" 1/32 0 0.023

Over 2-1/2" to 3-1/2" 3/64 0 0.035Over 3-1/2" to 4-1/2" 1/16 0 0.046Over 4-1/2" to 5-1/2" 5/64 0 0.058Over 5-1/2" to 6-1/2" 1/8 0 0.070Over 6-1/2" to 8" 5/32 0 0.085

Size Tolerance, InchesSpecified Size Square or Hexagons

Inches Over Under

.050" to 5/16" excl. 0 .002"5/16" to 1/2" excl. 0 .003"1/2" to 1" incl. 0 .004"Over 1" to 2" incl. 0 .006"Over 2" to 3" incl. 0 .008"Over 3" to 4" incl. 0 .010"

PER: ASTM A 484 (BAR) & ASTM A 555 ( WIRE)Note: A-286 Double Size Tolerance

COLD DRAWN BARS — HEXAGONS AND SQUARES

HOT ROLLED AND ROUGH TURNED ROUNDS,HOT ROLLED SQUARES

Specified Size,

* ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES.

Thickness Tolerance, In.,For Thickness Given

Over and Under

WidthTolerances,

InSpecified

WidthsIn. 1/8 to 1/2

Incl.Over 1/2To 1 Incl.

Over 1To 2 Incl.

Over 2 to 4Incl. Over Under

SUPER ALLOYAND

ELECTRICAL STEEL

85FRY STEEL COMPANY

(562) 802-2721


SUPER ALLOYAND

ELECTRICAL STEEL

Recommended Stock Removal**(Minimum Requirement Necessary To Qualify For Rejection)


86FRY STEEL COMPANY

(562) 802-2721

** NOTE: IT IS NOT ADVISABLE TO TRY TO “FINISH” ON SIZE FROM THE SIZE PURCHASED.

COLD DRAWN: ROUNDS — HEXAGONS — SQUARESUP TO & INCL. 5/16" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .003" PER SIDE*OVER 5/16" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1% OF DIAMETER PER SIDE*

CENTERLESS GROUND:ALL GROUND BAR SHOULD BE “DEFECT FREE” WITHIN THE STANDARD SIZE TOLERANCES OFANY MANUFACTURING DEFECTS. IE: SEAMS, LAPS, AND CRACKS.



ROUGH TURNED:ALL “R.T.” SIZES ARE PRODUCED ON THE PLUS SIDE.MATERIAL SHOULD BE DEFECT FREE ON SIZE OF ANY MANUFACTURING DEFECTS.IE: SEAMS, LAPS, AND CRACKS.


HR-A&P FLATS & SQUARESRECOMMENDED MACHINING ALLOWANCES (IN)

(A) (C)Specified 1/8" to over 1/2" over 1" over 2" over 3" over 4" over 6" Removal from

Width 1/2" incl. to 1" incl. to 2" incl. to 3" incl. to 4" incl. to 6" incl. to 8" incl. Width-Each Surface

Up to 1" Incl. .008 .010 -- -- -- -- -- .015

Over 1"-2" Incl. .012 .015 .031 -- -- -- -- .031

Over 2"-3" Incl. .015 .020 .031 .047 -- -- -- .047

Over 3"-4" Incl. .015 .020 .031 .047 .062 -- -- .062

Over 4"-6" Incl. .015 .020 .031 .047 .062 .093 -- .093

Over 6"-8" Incl. .024 .031 .035 .062 .078 .093 .141 .141

Over 8"-10" Incl. .024 .031 .035 .062 .078 .125 .156 .156

(A) SELECT THE “WIDTH” FIRST AND THEN READ ACROSS TO SPECIFIED THICKNESS:

(B)SELECT THE READING — THIS IS THE STOCK REMOVAL FOR THE THICKNESS PER SIDE:

(C)CONTINUE ACROSS ON SAME LINE FOR READING FOR WIDTH REMOVAL PER SIDE.

* NOTE: Product ordered to surface conditions other than ground, turned, or polished should,after removal of the standard machining allowance, be free from seams, laps, tears, cracks,and other defects exposed to the machined surfaces.

NOTE: Inspection prior to altering material is advisable.

(B)Removal from Thickness

Each Surface Specified Thickness

SUPER ALLOYAND

ELECTRICAL STEEL

[email protected]

(562) 802-2721


SUPER ALLOYAND

ELECTRICAL STEEL


87FRY STEEL COMPANY

(562) 802-2721

Maraging .03 .10 .10 .01 .01 .50 4.6/5.2 18./19. Co 8.5/9.5 Ti .50/.80“300” Al .05/.15 B.003 Zr .02 MINVAR-36 .15 1.0 .35 35./36.5 Se .15/.25“FM” Fe Bal MA-286 .08 2.0 1.0 .025 .025 13.5/16.0 1./1.5 24./27. .50 Ti 1.90/2.35 V .10/.50

Al .35 B.001/.01 Co 1.0 NM4750 .035 .80 .50 .02 .008 47./50. Bal. Fe ML-605 .05/.15 1.0/2.0 .40 .04 .03 19./21. 9./11. W 14./16. Fe 3.0

Bal Co NMNickel 200 .15 .35 .35 .01 99. Min .25 Fe .40 MNickel 400 .20 2.0 .50 .02 .015 63. Min Ni + Co 63. Min Co 1.0

Al .50 Pb .006 Zn .02Sn .006 Fe 2.5 INQUIRE

Nickel 405 .30 2.0 .50 .02 .025/.060 63./70. 28./34. Co 1.0 Al .50 Pb .006Zn .02 Sn .006 Fe 2.5 INQUIRE

Nickel K-500 .17 1.5 .50 .02 .01 63. Min Al 2.30/3.15 Co 1.0Ti .35/.85 Sn .006Fe 2.0 Pb .006 Zn .02 INQUIRE

Nickel 600 .15 1.0 .50 .015 14./17. .50 72. Min .50 Al .35 Ti .50Cb 1.0 Fe 6./10.Co 1.0 Ta .05 NM

Nickel 625 .10 .50 .50 .15 .015 20./23. 8./10. 58. Min Al .40 Ti .40Co 1.0 Cb 3.15/4.15Fe 5.0 Ta .05 NM

718 .08 .35 .35 .015 .015 17./21. 2.8/3.3 50./55. .30 Cb 4.75/5.5 Ta.05Pb .005 Co 1.0Bi .00003 Se .0003Ti .65/1.15 B .006Al .20/.80 Fe Bal NM

X-750 .08 1.0 .50 .01 14./17. Ni + Co .50 Co 1.0 Cb .70/1.270. Min Ti 2.25/2.75 Ta .05

Al .40/1.0 Fe 5./9. NM800 .10 1.5 1.0 .015 19./23. 30./35. 0.75 Al .15/.60 Ti .15/.60800-H .05/.10 1.5 1.0 .015 19./23. 30./35. 0.75 Fe 39.5 min NM800-HT .06/.10 1.5 1.0 .015 19./23. 30./35. 0.75825 .05 1.0 .50 .03 19.5/23.5 2.5/3.5 38./46. 1.5/3.0 Ti .60/1.20 Al .20

Fe 22.0 min NM2Waspaloy .02/.10 .10 .15 .015 .015 18./21. 3.5/5.0 Balance .10 Co 12./15. Pb.0005

Ti 2.75/3.25 Bi .00003Al 1.2/1.6 Zr .02/.08 Se .0003B .003/.01 Fe 2. Ti 1.0 NM

4MP 35N .025 .15 .15 .015 .01 19./21. 9./10.5 33./37. Ti 1.0 Co Bal Fe 1.0 NM4MP 159 .04 .20 .20 .02 .01 18./20. 6.0/8.0 Balance Al .10/.30 Ti 2.5/3.25

Cb .25/.75 Co 34./38.Fe 8./10. B .03 NM

Fry Alloy X .05/0.15 1.0 1.0 .04 .03 20.5/23. 8./10. Balance .50 Co .5/2.5 W .20/1.0B .01 Fe 17./20.Al .50 Ti .15 NM

Fry Alloy C .01 1.0 .08 .04 .03 14.5/16.5 15./17. Balance Co 2.5 W 3.0/4.5V .35 Fe 4./7. NM

3Kovar .04 .50 .20 .20 .20 29.0 .20 Co. 17.0 Mg.10 Fe Bal Al .10 Ti .10 Zr .10Ti + Al + Mg + Zr .20 M

3Aermet 100 .21/.25 .10 .10 .008 .005 2.9/3.3 1.1/1.3 11./12. Co 13./14. Ti .015Al .015 P + S .01N .0015 O2 .002 M

CHEMICAL ANALYSES — Maximum Unless IndicatedMAN- PHOS- MOLYB-

TYPE CARBON GANESE SILICON PHORUS SULFER CHROME DENUM NICKEL COPPER OTHERS

M – MagneticNM – Non-magnetic

The above chart is a compilation of Aerospace, ASTM, Federal and Military specifications. It is for reference only and should not be used for design or specifications.

2 Trademark United Technology 3 Trademark Carpenter Technology 4Trademark SPS Technology

SUPER ALLOYAND

ELECTRICAL STEEL

87FRY STEEL COMPANY

(562) 802-2721


SUPER ALLOYAND

ELECTRICAL STEEL

MACHINABILITY RATINGS


88FRY STEEL COMPANY

(562) 802-2721

Maraging “300” 60 36A-286 54 28A-286 Cold Red. 50 224750 60 36L-605 15 9Nickel “200” 110 66Nickel “400” 80 48Nickel “405” 80 48Nickel “K-500” 60 36Nickel “K-500” Aged 40 25Nickel “600” 50 22Nickel “625” 20 12Nickel “825” 47 20718 20 12718 Cold Red 18 10

X-750 20 12800 50 22800 H 50 22800 HT 50 22INVAR 36 “FM” 92 552Waspaloy 45 20Waspaloy Cold Red 41 184MP 35N 45 204MP 159 45 20Fry Alloy C 40 18Fry Alloy X 45 203Kovar 60 22Aermet 100* 280 —

%RELATIVE SPEEDBASED ONC-1212 AS

100% (165 SFM)

These machinability ratios must be recognized as approximate values.

2 Trademark United Technology 3 Trademark Carpenter Technology 4Trademark SPS Technology

APPROXIMATESURF. FT.PER MIN.GRADE

%RELATIVE SPEEDBASED ON

C-1212 AS 100%

APPROXIMATESURF. FT.PER MIN.GRADE

* Based on Carbide Tooling

SUPER ALLOYAND

ELECTRICAL STEEL

[email protected]

(562) 802-2721


AIR

CR

AFT

ALLO

Y

AIR

CR

AFT

ALL

OY

AIRCRAFT ALLOYGRADES STOCKED


[email protected]

(562) 802-2721


E-8740 AMS-6322, MIL-S-6049 EXC. SONIC,AMS-2301, AMS-2304, ASTM-A-331,AMS-S-6049 EXC. SONIC

E-9310 N&T MIL-S-7393 COMP. 3, AMS-6260,AMS-2301, AMS-2304, ASTM-A-322,CAP. OF HT-5042

E-9310 VAC. MELT. N&T

MIL-S-7393 COMP. 3, AMS-6265,AMS-6260, AMS-2300, AMS-6267,MIL-S-83030 COMP. 3, CAP. OF HT-5042, BPS-299-947-032 (EXC. HARDNESS), EMS-56280

E-52100 VAC. MELT. MIL-S-7420, AMS-6444, AMS-6440,(SPH. ANN) AMS-2300, AMS-S-7420

D6AC VAC. MELT. AMS-6431, AMS-2300, STM-05-500, LCM-05-2190, EXC. SONIC TO FOLLOWING: FMS-1011, GM-1013, MIL-S-8949, AMS-S-8949

H-11 VAC. MELT. AMS-6485, AMS-6487, AMS-6488,EMS-642 (EXC. FATIGUE TEST)

HY-TUF N&T MIL-S-7108, AMS-6418, AMS-2301,AMS-2304, ASTM-A-322, AMS-S-7108, DMS-1841 GRD. B

HY-TUF VAC. MELT. N&TMIL-S-7108, AMS-6418 CHEMSONLY, AMS-6425, AMS-2300, AMS-S-7108, DMS-1841 GRD. A

NITRIDING HT (BHN 241-285)MIL-S-6709 COMP. A 135 MODIFIED,AMS-6470 EXC. HARDNESS, AMS-6472, AMS-2301, AMS-2304, ASTM-A-322, AMS-S-6709

NITRIDING VAC. MELT.

MIL-S-6709 COMP. A 135 MODIFIED,AMS-6471, AMS-2300, AMS-S-6709,BELL 299-947-036

9-4-30 VAC. MELT. AMS-6526 EXC. AS SHIPPED COND,MIL-STD-2154 CL. A, BMS-7-182 TYPE 2, STO-160-LBO-012, MMS-2102 (EXC. FRACTURE TOUGH. & SONIC)

AUTOMATIC EXCEPTIONS TO THE SPECS LISTED ARE: LINE MARKING AND INSPECTION (I.E. MAG., SONIC, ETC.)

E-4130 MIL-S-6758, AMS-6370, AMS-S-6758,AMS-2301, AMS-6348, AMS-2304,ASTM-A-331 (C.F. ONLY), ASTM-A-322(H.R. ONLY)

E-4130 H.T. MIL-S-6758, AMS-6346, AMS-6370 CHEMS ONLY, AMS-2301, AMS-2304,ASTM-A-331, AMS-S-6758

E-4140 ANN. MIL-S-5626, AMS-6382, AMS-6349 EXC. COND., AMS-2301, AMS-2304,ASTM-A-331, AMS-S-5626

E-4140 NORM. MIL-S-5626, AMS-6382 EXC. COND.,AMS-6349, AMS-2301, AMS-2304,AMS-6529, ASTM-A-322, AMS-S-5626

E-4330 MOD. VAC. MELT. N&T

MIL-S-8699, AMS-6411, AMS-6427,AMS-2300, BMS-7-122, BMS-7-27,CE-0906, EXC. SONIC TO FOLLOWING:FMS-1012, GM-1010, EMS-96242

E-4340 N&T MIL-S-5000, AMS-6415, AMS-6484,AMS-6409, AMS-2301, AMS-2304,AMS-2310, ASTM-A-331 (C.F. ONLY),ASTM-A-322 (H.R. ONLY), BMS-7-28,DMS-1555 GRD. B, AMS-S-5000

E-4340 VAC. MELT. N&T

MIL-S-8844 CL 1, MIL-S-5000, AMS-6414, AMS-6415, AMS-2300, AMS-6484, AMS-S-5000, BPS-299-947-055, DMS-1555 GRD.A , BMS-7-28

E-4340 VAC. MELT. N&T “300M”

MIL-S-8844 CL. 3, MIL-S-83135,AMS-6417, AMS-6419, AMS-6257 EXC. HARDNESS, AMS-2300, LC-05-1190, DMS-1935, BMS-7-26 CL. 1,GM-1012, CE-0896

E-4620 VAC. MELT. MIL-S-7493, AMS-6294, AMS-2300, ASTM-A-331 (C.F. ONLY), ASTM-A-322 (H.R. ONLY)

E-6150 VAC. MELT. MIL-S-8503, AMS-6448, AMS-2300,AMS-S-8503, ASTM-A-331 (C.F.ONLY), ASTM-A-322 (H.R. ONLY)


AIRCRAFT ALLOYROUNDSSTOCKED IN 12' R/L


91FRY STEEL COMPANY

(562) 802-2721


13/32" E-4130 C.D. H.T.E-4130 C.D. Norm

7/16" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-52100 V.M. C.G. Ann.

.4475" H-11 V.M. C.G. Ann.E-4340 G&P N&TE-4340 V.M. C.G. N&TE-8740 G&P Ann.

15/32" E-4130 C.D. H.T.E-4130 C.D. Norm

.484" H-11 V.M. C.G. Ann.

1/2" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4340 V.M. C.G. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. C.G. N&T

.510" D6AC V.M. C.G. N&TH-11 V.M. C.G. Ann.E-4330 Mod V.M. C.G. N&TE-4340 G&P N&TE-4340 V.M. C.G. N&TE-4340 Mod V.M. “300M” C.G. N&TE-8740 G&P Ann.

.525" H-11 V.M. C.G. Ann.

17/32" E-4130 C.D. H.T.E-4130 C.D. Norm

.540" H-11 V.M. C.G. Ann.

9/16" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

.5725" E-4340 G&P N&TH-11 V.M. C.G. Ann.E-8740 G&P Ann.

.587" H-11 V.M. C.G. Ann.

1/8" E-4130 C.D. Norm

3/16" E-4130 C.D. H.T.E-4130 C.D. Norm

7/32" E-4130 C.D. Norm

.220" E-8740 G&P Ann.

1/4" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

.260 “ H-11 V.M. C.G. Ann.E-4340 V.M. C.G. N&TE-4340 G&P N&TE-8740 G&P Ann.

.270" H-11 V.M. C.G. Ann.

9/32" E-4130 C.D. H.T.E-4130 C.D. Norm

5/16" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T


21/64" E-4130 C.D. Norm

11/32" E-4130 C.D. Norm

3/8" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. C.G. N&T


.391" H-11 V.M. C.G. Ann.

25/64" E-4130 C.D. Norm

Finish: C.D. – Cold Drawn Condition: Ann. – Annealed V.M. - Vacuum Arc Re-melt Norm - NormalizedC.G. – Centerless Ground N&T – Normalized and Sub-critical Annealed P.G. - Precision GroundR.T. – Rough Turned H.T. – Heat treated (RC 26/32) RCS - Round Corner SquareG&P -Ground and Polished C.D/T. - Turned to a Cold Drawn tol. HRRT – Hot Rolled and Rough Turned



AIRCRAFT ALLOY ROUNDSSTOCKED IN 12' R/L


[email protected]

(562) 802-2721


13/16" E-4140 C.D. Ann.E-4340 C.D. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

7/8" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T9-4-30 V.M. C.G. N&T

.885" D6AC V.M. C.G. N&TH-11 V.M. C.G. Ann.E-4340 G&P N&TE-4340 Mod V.M. “300M” C.G. N&TE-8740 G&P Ann.

.900" H-11 V.M. C.G. Ann.

15/16" H-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-52100 V.M. C.G. Ann.

1" D6AC V.M. C.G. N&TH-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. NormE-4130 R.T. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 H.R. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. C.G. N&T

5/8" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4340 C.D. N&TE-4340 V.M. C.G. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. C.G. N&T

.635" H-11 V.M. C.G. Ann.E-4340 G&P N&TE-4340 V.M. C.G. N&TE-4340 Mod V.M. “300M” C.G. N&TE-8740 G&P Ann.

.649" H-11 V.M. C.G. Ann.

11/16" H-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

.725" H-11 V.M. C.G. Ann.

3/4" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. C.G. N&T9-4-30 V.M. C.G. N&T

.760" D6AC V.M. C.G. N&TH-11 V.M. C.G. Ann.E-4330 Mod V.M. C.G. N&TE-4340 G&P N&TE-4340 V.M. C.G. N&TE-4340 Mod V.M. “300M” C.G. N&TE-8740 G&P Ann.

13/16" H-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. Norm



93FRY STEEL COMPANY

(562) 802-2721

1-1/4" E-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. C.G. N&T

1.260" E-4340 G&P N&T.E-8740 G&P Ann.

1-5/16" E-4130 C.D./T. H.T.E-4130 C.D./T. NormE-4140 C.D./T. Ann.E-4340 C.D. N&T

1-3/8" D6AC V.M. C.G. N&TD6AC V.M. R.T. N&TH-11 V.M. C.G. AnnE-4130 C.D./T. H.T.E-4130 C.D./T. NormE-4140 C.D./T. Ann.E-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 R.T. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M.“300M” C.G. N&TE-4340 Mod V.M.“300M” R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

1-7/16" H-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4140 C.D./T. Ann.E-4340 C.D. N&T

1-1/2" D6AC V.M. C.G. N&TD6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. H.T.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. C.G. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T

1.010" H-11 V.M. C.G. Ann.E-4330 Mod V.M. C.G. N&TE-4340 G&P N&TE-4340 V.M. C.G. N&TE-8740 G&P Ann.

1.020" H-11 V.M. C.G. Ann.

1-1/16" H-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-1/8" D6AC V.M. C.G. N&TH-11 V.M. C.G. Ann.E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 R.T. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. C.G. N&TE-9310 V.M. R.T. N&TE-52100 V.M. C.G. Ann.Nitriding V.M. C.G. N&T

1.135" H-11 V.M. C.G. Ann.E-4330 Mod V.M. C.G. N&TE-4340 G&P N&TE-4340 V.M. C.G. N&TE-8740 G&P Ann.

1-3/16" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-1/4" D6AC V.M. C.G. N&TD6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. H.T.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. C.G. N&TE-4330 Mod V.M. R.T. N&TE-4340 C.D. N&TE-4340 R.T. N&TE-4340 V.M. C.G. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” C.G. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. C.G. As rolledE-6150 V.M. C.G. Ann.E-9310 V.M. C.G. N&T







[email protected]

(562) 802-2721


2" H-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

2-1/8" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE 4140 C.D./T. Ann.E-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

2-3/16" E-4130 C.D./T. Norm

2-1/4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

2-3/8" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&T

1-1/2" 9-4-30 V.M. C.G. N&T

1.510" E-8740 G&P Ann.

1-9/16 " E-4130 C.D./T. NormE-4140 C.D./T. Ann.E-4340 C.D./T. N&T

1-5/8" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding V.M. R.T. N&T

1-3/4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding V.M. R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

1-7/8" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 V.M . R.T. N&TE-52100 V.M. R.T. Ann.Nitriding V.M. R.T. N&T

2" D6AC V.M. R.T. N&T



95FRY STEEL COMPANY

(562) 802-2721

2-7/8" E-4140 C.D./T. Ann.E-4140 R.T. NormE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&T

3" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

3-1/8" E-4130 C.D./T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-9310 V.M. R.T. N&T

3-1/4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&T9-4-30 V.M. R.T. N&T

3-3/8" E-4130 C.D./T. NormE-4130 R.T. NormE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-9310 V.M. R.T. N&T

3-1/2" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.

2-3/8" E-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&TNitriding R.T. H.T.

2-1/2" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

2-5/8" E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

2-3/4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M . R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

2-7/8" E-4130 C.D./T. NormE-4130 R.T. Norm







[email protected]

(562) 802-2721


4" 9-4-30 V.M. R.T. N&T

4-1/4" E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

4-1/2" H-11 V.M. R.T. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Hy-Tuf R.T. N&T

4-3/4" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

5" H-11 V.M. R.T. Ann.E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-9310 R.T. N&TE-9310 V.M. R.T. N&TNitriding R.T. H.T.

5-1/4" E-4130 R.T. NormE-4140 R.T. NormE-4330 V.M. R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

5-1/2" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 R.T. N&T

3-1/2" E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE 9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T9-4-30 V.M. R.T. N&T

3-5/8" E-4130 R.T. NormE-4140 R.T. Norm

3-3/4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding V.M. R.T. N&T

3-7/8" E-4340 R.T. N&T

4" D6AC V.M. R.T. N&TH-11 V.M. C.G. Ann.E-4130 C.D./T. NormE-4130 R.T. NormE-4140 C.D./T. Ann.E-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 C.D./T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-6150 V.M. R.T. Ann.E-9310 R.T. N&TE-9310 V.M. R.T. N&TE-52100 V.M. R.T. Ann.Nitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf R.T. N&THy-Tuf V.M. R.T. N&T



97FRY STEEL COMPANY

(562) 802-2721

7-3/4" E-9310 R.T. N&T

8" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod VM R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 MOD V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&T

8-1/4" E-4340 R.T. N&T

8-1/2" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&T

9" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod VM R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-9310 V.M. R.T. N&T

9-1/2 " E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&T

10" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod VM R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-9310 V.M. R.T. N&T

10-1/2" E-4340 R.T. N&TE-4340 V.M. R.T. N&T

11" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&T

12" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&T

13" E-4130 R.T. NormE-4340 R.T. N&T

14" E-4130 R.T. NormE-4340 R.T. N&T

16" E-4130 R.T. NormE-4340 R.T. N&T

18" E-4130 R.T. NormE-4340 R.T. N&T

20" E-4130 R.T. NormE-4340 R.T. N&T

5-1/2" E-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&TNitriding R.T. H.T.

5-3/4" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&T

6" D6AC V.M. R.T. N&TH-11 V.M. R.T. Ann.E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod V.M. R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-4620 V.M. R.T. As rolledE-9310 R.T. N&TE-9310 V.M. R.T. N&TNitriding R.T. H.T.Nitriding V.M. R.T. N&THy-Tuf V.M. R.T. N&T

6-1/4" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&TE-4340 MOD V.M. “300M” R.T. N&T

6-1/2" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&T

6-3/4" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&TE-9310 V.M. R.T. N&T

7" E-4130 R.T. NormE-4140 R.T. NormE-4330 Mod VM R.T. N&TE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 R.T. N&TE-9310 V.M. R.T. N&T

7-1/4" E-4340 R.T. N&T

7-1/2" E-4130 R.T. NormE-4140 R.T. NormE-4340 R.T. N&TE-4340 V.M. R.T. N&TE-4340 Mod V.M. “300M” R.T. N&TE-9310 V.M. R.T. N&T

7-3/4" E-4340 R.T. N&T



AIRCRAFT ALLOY



[email protected]

(562) 802-2721

15/16" E-4130 C.D. H.T.

1" E-4130 C.D. NormE-4130 C.D. H.T.E-4140 C.D. Ann.E-4340 C.D. N&T

1-1/16" E-4130 C.D. N&TE-4340 C.D. N&T

1-1/8" E-4130 C.D. NormE-4130 C.D. H.T.E-4140 C.D. Ann.

1-1/4" E-4130 C.D. NormE-4130 C.D. H.T.E-4140 C.D. Ann.E-4340 C.D. N&T

1-3/8" E-4130 C.D. NormE-4140 C.D. Ann.

1-1/2" E-4130 C.D. NormE-4130 C.D. H.T.E-4140 C.D. Ann.E-4340 C.D. N&T

1-5/8" E-4130 C.D. Norm

1-3/4" E-4130 C.D. NormE-4340 C.D. N&T

2" E-4130 C.D. NormE-4340 C.D. N&T

1/4" E-4130 C.D. NormE-4340 C.D. N&T

5/16" E-4130 C.D. Norm

3/8" E-4130 C.D. NormE-4130 C.D. H.T.E-4340 C.D. N&T

7/16" E-4130 C.D. H.T.

1/2" E-4130 C.D. NormE-4130 C.D. H.T.E-4140 C.D. Ann.E-4340 C.D. N&T

9/16" E-4130 C.D. NormE-4130 C.D. H.T.


11/16" E-4130 C.D. Norm


13/16" E-4130 C.D. H.T.




AIRCRAFT ALLOYSQUARESSTOCKED IN 12' R/L


99FRY STEEL COMPANY

(562) 802-2721


2-1/2" E-4340 C.D. N&TE-4340 H.R.-RCS N&TE-4340 V.M. H.R. N&T

2-3/4" E-4340 H.R.-RCS N&TE-4340 V.M. H.R. N&T

3" E-4130 H.R.-RCS NormE-4140 H.R.-RCS NormE-4340 H.R.-RCS N&TE-4340 V.M. H.R. N&T

3-1/2" E-4130 H.R.-RCS NormE-4140 H.R.-RCS NormE-4340 H.R.-RCS N&T




1/4" E-4130 C.D. H.T.E-4340 C.D. N&T

5/16" E-4130 C.D. H.T.

3/8" E-4130 C.D. H.T.E-4340 C.D. N&T

7/16" E-4130 C.D. H.T.

1/2" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. C.D. N&T

5/8" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

3/4" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. C.D. N&T

7/8" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.

1" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. C.D. N&T

1-1/8" E-4130 C.D. H.T.E-4130 C.D. Norm

1-1/4" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. C.D. N&T

1-1/2" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. H.R. N&T

1-3/4" E-4340 V.M H.R. N&T

2" E-4130 H.R.-RCS NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 H.R. N&TE-4340 V.M. H.R. N&T

2-1/4" E-4130 H.R.-RCS NormE-4140 H.R.-RCS NormE-4340 H.R.-RCS N&TE-4340 V.M. H.R. N&T

2-1/2" E-4130 H.R.-RCS NormE-4140 H.R.-RCS Norm



AIRCRAFT ALLOY

FLATSSTOCKED IN 12' R/L


[email protected]

(562) 802-2721

1/2" x 1" E-4140 C.D. Ann.E-4340 C.D. N&T

1-1/4" E-4130 C.D. Norm

1-1/2" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-3/4" E-4130 C.D. Norm

2" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. H.R. N&T


3" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T


5" E-4130 C.D. Norm


5/8" x 1" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-1/4" E-4130 C.D. Norm

1-1/2" E-4130 C.D. NormE-4340 C.D. N&T


2-1/2" E-4130 C.D. Norm

3" E-4130 C.D. NormE-4140 C.D. Ann.

4" E-4130 C.D. NormE-4340 C.D. N&T

6" E-4130 C.D. Norm

3/4" x 1" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. H.R. N&T

1-1/4" E-4130 C.D. NormE-4140 C.D. Ann.

1-1/2" E-4130 C.D. H.T.

3/16" x 1" E-4130 C.D. Norm

1-1/2" E-4130 C.D. Norm

2" E-4130 C.D. Norm

1/4" x 1" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-1/4" E-4130 C.D. Norm


1-3/4" E-4130 C.D. Norm


2-1/2" E-4130 C.D. Norm

3" E-4130 C.D. Norm

4" E-4130 C.D. Norm

5" E-4130 C.D. Norm

5/16" x 1" E-4130 C.D. Norm

1-1/2" E-4130 C.D. Norm

2" E-4130 C.D. Norm

3/8" x 3/4" E-4130 C.D. Norm

1" E-4130 C.D. NormE-4140 C.D. Ann.

1-1/4" E-4130 C.D. Norm


1-3/4" E-4130 C.D. Norm

2" E-4130 C.D. NormE-4340 C.D. N&T

2-1/2" E-4130 C.D. NormE-4340 C.D. N&T

3" E-4130 C.D. NormE-4340 C.D. N&T

4" E-4130 C.D. NormE-4140 C.D. Ann.

5" E-4130 C.D. Norm

6" E-4130 C.D. Norm

1/2" x 3/4" E-4130 C.D. Norm

1" E-4130 C.D. Norm




AIRCRAFT ALLOY



101FRY STEEL COMPANY

(562) 802-2721


1" x 5" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

6" E-4130 C.D. NormE-4340 C.D. N&T

1-1/4"x 1-1/2" E-4130 C.D. NormE-4340 C.D. N&T

2" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

2-1/2" E-4130 C.D. NormE-4340 C.D. N&T

3" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

4" E-4130 C.D. NormE-4340 C.D. N&T

5" E-4340 C.D. N&T

6" E-4130 C.D. NormE-4340 C.D. N&T

1-1/2"x 1-3/4" E-4130 C.D. Norm

2" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. H.R. N&T

2-1/2" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&TE-4340 V.M. H.R. N&T


4" E-4130 C.D. NormE-4340 C.D. N&TE-4340 V.M. H.R. N&T

5" E-4130 C.D. NormE-4340 C.D. N&T


1-3/4"x 3" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.

3/4" x 1-1/2"" E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T

1-3/4" E-4130 C.D. Norm


2-1/2" E-4130 C.D. NormE-4140 C.D. Ann.



5" E-4130 C.D. Norm

6" E-4130 C.D. NormE-4340 C.D. N&T

1" x 1-1/4" E-4130 C.D. H.T.E-4130 C.D. NormE-4140 C.D. Ann.E-4340 C.D. N&T


1-3/4" E-4130 C.D. NormE-4140 C.D. Ann.






AIRCRAFT ALLOY



[email protected]

(562) 802-2721

2-1/2"x 6" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

3" x 4" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&TE-4340 V.M. H.R. N&T

5" E-4130 C.D. NormE-4130 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

6" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

3-1/2" x 4" E-4140 H.R. NormE-4340 C.D. N&T

6" E-4340 C.D. N&TE-4340 H.R. N&T

4" x 5" E-4340 H.R. N&T

6" E-4130 H.R. NormE-4140 H.R. NormE-4340 H.R. N&T

1-3/4"x 3" E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

4" E-4130 H.R. NormE-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

2" x 2-1/2" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

3" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&TE-4340 V.M. H.R. N&T

3-1/2" E-4340 H.R. N&T

4" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&TE-4340 V.M. H.R. N&T

5" E-4130 C.D. NormE-4130 H.R. NormE-4340 C.D. N&T

6" E-4130 C.D. NormE-4130 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

2-1/2"x 3" E-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

3-1/2" E-4340 C.D. N&TE-4340 H.R. N&T

4" E-4130 C.D. NormE-4130 H.R. NormE-4140 C.D. Ann.E-4140 H.R. NormE-4340 C.D. N&TE-4340 H.R. N&T

5" E-4130 C.D. NormE-4340 C.D. N&TE-4340 H.R. N&T




AIRCRAFT ALLOY WEIGHTS

ROUNDS



(562) 802-2721



1/8" .004 .042 .503/16" .008 .094 1.137/32" .011 .128 1.54.220" .011 .129 1.5481/4" .014 .167 2.00.270" .016 .1946 2.3359/32" .018 .211 2.535/16" .022 .261 3.13.3225" .023 .277 3.32421/64" .024 .287 3.4411/32" .026 .316 3.793/8" .031 .376 4.51.385" .033 .395 4.7425/64" .034 .407 4.88.391" .034 .4008 4.89613/32" .037 .441 5.297/16" .043 .511 6.13.4475" .045 .535 6.4215/32" .049 .587 7.04.484" .052 .626 7.5121/2" .056 .668 8.02.510" .058 .694 8.32833/64" .059 .710 8.52.525" .061 .7359 8.83117/32" .063 .754 9.05.540" .066 .795 9.549/16" .070 .845 10.14.5725" .073 .875 10.50.587" .077 .928 11.1365/8" .087 1.043 12.52.635" .089 1.07 12.84.649" .093 1.12 13.4411/16" .105 1.262 15.14.725" .117 1.40 16.803/4" .125 1.502 18.02.760" .128 1.54 18.4813/16" .147 1.763 21.167/8" .170 2.044 24.53.885" .174 2.09 25.08.900" .180 2.16 25.9215/16" .192 2.347 28.16

1" .22 2.670 32.04.010" .228 2.733 32.796.020" .231 2.77 33.241/16" .25 3.014 36.171/8" .28 3.379 40.55.135" .287 3.44 41.283/16" .31 3.766 45.191/4" .35 4.173 50.08.260" .353 4.24 50.885/16" .38 4.600 55.203/8" .42 5.049 60.597/16" .46 5.518 66.221/2" .50 6.008 72.10.510" .518 6.21 74.529/16" .54 6.520 78.245/8" .59 7.051 84.61

1" 3/4" .68 8.178 98.147/8" .78 9.388 112.70

2" .89 10.68 128.21/8" 1.01 12.06 144.73/16" 1.07 12.78 153.41/4" 1.13 13.52 162.23/8" 1.26 15.06 180.71/2" 1.39 16.69 200.35/8" 1.54 18.40 220.83/4" 1.69 20.20 242.47/8" 1.84 22.07 264.8

3" 2.01 24.03 288.41/8" 2.18 26.08 312.91/4" 2.36 28.21 338.53/8" 2.54 30.42 365.01/2" 2.73 32.71 392.55/8" 2.93 35.09 421.13/4" 3.14 37.55 450.67/8" 3.34 40.10 481.2

4" 3.56 42.73 512.61/4" 4.02 48.23 578.71/2" 4.51 54.07 648.93/4" 5.03 60.25 723.0

5" 5.56 66.75 801.11/4" 6.13 73.60 883.21/2" 6.73 80.77 969.23/4" 7.36 88.29 1059.0

6" 8.01 96.12 1153.51/4" 8.71 104.3 1252.01/2" 9.40 112.8 1353.83/4" 10.14 121.7 1460.0

7" 10.90 130.8 1570.81/4" 11.70 140.4 1684.81/2" 12.52 150.2 1802.23/4" 13.42 161.0 1932.0

8" 14.24 170.9 2050.61/4" 15.17 182.0 2184.01/2" 16.08 192.9 2315.03/4" 17.09 205.1 2461.2

9" 18.02 216.3 2595.21/2" 20.08 241.0 2891.6

10" 22.25 267.0 3204.01/2" 24.67 296.0 3552.0

11" 27.00 324.0 3888.0

12" 32.17 386.0 4632.0

13" 38.0 456.0 5472.0

14" 43.67 524.0 6288.0

16" 57.50 690.0 8280.0

18" 72.17 866.0 10392.0

20" 89.17 1070.0 12840.0


HEXAGONS


[email protected]

(562) 802-2721



3/16" .009 .104 1.251/4" .015 .184 2.215/16" .02 .288 3.463/8" .03 .414 4.977/16" .05 .564 6.771/2" .06 .736 8.839/16" .08 .932 11.185/8" .10 1.150 13.8011/16" .12 1.392 16.703/4" .14 1.656 19.8713/16" .16 1.944 23.337/8" .19 2.254 27.0515/16" .22 2.588 31.06

1" .25 2.945 35.341/16" .28 3.324 39.891/8" .31 3.727 44.72

1" 3/16" .35 4.152 49.821/4" .38 4.601 55.213/8" .46 5.567 66.801/2" .55 6.625 79.505/8" .65 7.775 93.303/4" .75 9.019 108.23

2" .98 11.78 141.41/4" 1.24 14.91 178.91/2" 1.53 18.40 220.8


SQUARESEstimated Weight, Lbs.

Size in Inches Per Inch Per Foot 12 Ft. Bar


1/4" .017 .213 2.5505/16" .03 .332 3.9813/8" .04 .478 5.7367/16" .05 .651 7.8101/2" .07 .850 10.2005/8" .11 1.328 15.9403/4" .16 1.913 22.9607/8" .22 2.603 31.240

1" .28 3.400 40.801/8" .36 4.303 51.641/4" .44 5.313 63.761/2" .64 7.650 91.803/4" .87 10.410 124.95

2" 1.13 13.600 163.21/4" 1.43 17.21 206.61/2" 1.77 21.25 255.0

2" 3/4" 2.14 25.72 308.6

3" 2.55 30.6 367.21/2" 3.47 41.65 500.0

4" 4.53 54.4 652.8

5" 7.08 85.0 1020.0

6" 10.25 123.0 1476.0


FLATS



(562) 802-2721



3/16" x 1" .053 .638 7.661-1/2" .080 .956 11.472" .106 1.275 15.30

1/4" x 1" .071 .850 10.201-1/2" .106 1.275 15.301-3/4" .124 1.488 17.862" .142 1.700 20.402-1/2" .177 2.125 25.503" .213 2.550 30.604" .283 3.400 40.80

5/16" x 1" .089 1.063 12.761-1/2" .133 1.594 19.132" .177 2.125 25.50

3/8" x 3/4" .080 .956 11.471" .106 1.275 15.301-1/4" .133 1.594 19.131-1/2" .159 1.913 22.961-3/4" .186 2.231 26.772" .213 2.550 30.602-1/2" .266 3.188 38.263" .319 3.825 45.904" .425 5.100 61.20

1/2" x 3/4" .106 1.275 15.301" .142 1.700 20.401-1/4" .177 2.125 25.501-1/2" .213 2.550 30.601-3/4" .248 2.975 35.702" .283 3.400 40.802-1/2" .354 4.250 51.003" .425 5.100 61.204" .567 6.800 81.605" .708 8.500 102.006" .850 10.200 122.40

5/8" x 1" .177 2.125 25.501-1/4" .221 2.656 31.871-1/2" .266 3.188 38.261-3/4" .310 3.719 44.632" .354 4.250 51.002-1/2" .438 5.313 63.763" .531 6.375 76.504" .708 8.500 102.006" 1.060 12.750 153.00

3/4" x 1" .213 2.550 30.601-1/4" .266 3.188 38.261-1/2" .319 3.825 45.901-3/4" .372 4.463 53.562" .425 5.100 61.202-1/2" .531 6.375 76.603" .637 7.650 91.804" .850 10.200 122.40

3/4" x 5" 1.060 12.750 153.00

3/4" x 6" 1.280 15.300 186.30

1" x 1-1/4" .354 4.250 51.001-1/2" .425 5.100 61.201-3/4" .496 5.950 71.402" .567 6.800 81.602-1/2" .708 8.500 102.003" .850 10.200 122.404" 1.130 13.600 163.205" 1.420 17.000 204.006" 1.700 20.400 244.80

1-1/4" x 1-1/2" .531 6.375 76.502" .708 8.500 102.002-1/2" .885 10.630 127.603" 1.060 12.750 153.004" 1.420 17.000 204.005" 1.770 21.250 255.006" 2.130 25.500 306.00

1-1/2"x 1-3/4" .744 8.920 107.102" .850 10.200 122.402-1/2" 1.060 12.750 153.003" 1.280 15.300 183.604" 1.700 20.400 244.805" 2.13 25.50 306.006" 2.55 30.60 367.20

1-3/4"x 3" 1.49 17.85 214.204" 1.98 23.80 285.60

2" x 2-1/2" 1.42 17.00 204.003" 1.70 20.40 244.803-1/2" 1.98 23.80 285.604" 2.27 27.20 326.005" 2.83 34.00 408.006" 3.40 40.80 489.60

2-1/2"x 3" 2.13 25.50 306.003-1/2" 2.48 29.75 357.004" 2.83 34.00 408.005" 3.54 42.50 510.006" 4.25 51.00 612.00

3" x 4" 3.40 40.80 489.605" 4.25 51.00 612.006" 5.10 61.20 734.40

3-1/2"x 4" 3.97 47.60 571.006" 5.95 71.40 857.00

4" x 5" 5.67 68.04 816.486" 6.80 81.60 979.20

AIRCRAFT ALLOYSIZE TOLERANCES


[email protected]

(562) 802-2721

HOT ROLLED BARS — FLATSTolerances for Thickness and Width

SpecifiedWidths, In.

Thickness Tolerance for Thickness Given Over or Under, In. Width Tolerance, In.

Under 1/4 1/4 to 1/2 incl. Over 1/2 to 1 incl. Over 1 to 2 incl. Over 2 to 4 incl. Over Under

0.007" 0.008" 0.010" - -0.007" 0.012" 0.015" 1/32" -0.008" 0.015" 0.020" 1/32" 3/64"0.009" 0.015" 0.020" 1/32" 1/16"

To 1" incl.Over 1" to 2" incl.Over 2" to 4" incl.Over 4" to 6" incl.

1/64" 1/64"1/32" 1/32"1/16" 1/32"3/32" 1/16"

HOT ROLLED SQUARES ANDHOT ROLLED OR ROUGH TURNED ROUNDS

Corner Radii

Nominal Sizes* Nominal CornerInches Radii, Inches

2" to 2-7/16" incl. 5/16"2-1/2" to 2-7/8" incl. 3/8"3" to 3-3/8" incl. 7/16"3-1/2" to 3-7/8" incl. 1/2"4" to 4-3/8" incl. 5/8"4-1/2" to 6" incl. 3/4"

*Sizes are the distances between opposite sides.Round-cornered squares are rolled to dimensions,not to weights per linear foot.

HOT ROLLED BARS ROUND CORNERED SQUARESSize Tolerance, In. Out-of-Round

Specified Sizes, In. Over Under or Square, In.

Over 7/8" to 1" incl. 0.009" 0.009" 0.013"Over 1" to 1-1/8" incl. 0.010" 0.010" 0.015"Over 1-1/8"to 1-1/4" incl. 0.011" 0.011" 0.016"Over 1-1/4"to 1-3/8" incl. 0.012" 0.012" 0.018"Over 1-3/8"to 1-1/2" incl. 0.014" 0.014" 0.021"Over 1-1/2"to 2" incl. 1/64" 1/64" 0.023"Over 2" to 2-1/2" incl. 1/32" 0 0.023"Over 2-1/2"to 3-1/2" incl. 3/64" 0 0.035"Over 3-1/2"to 4-1/2" incl. 1/16" 0 0.046"Over 4-1/2"to 5-1/2" incl. 5/64" 0 0.058"Over 5-1/2"to 6-1/2" incl. 1/8" 0 0.070"Over 6-1/2"to 8-1/4" incl. 5/32" 0 0.085"Over 8-1/4"to 9-1/2" incl. 3/16" 0 0.100"Over 9-1/2"to 12" incl. 1/4" 0

COLD FINISHED BARSAll Tolerances are in Inch and are Minus

To 1-1/2" incl. 0.004" 0.006"Over 1-1/2" to 2-1/2" incl. 0.005" 0.007"Over 2-1/2" to 4" incl. 0.006" 0.008"Over 4" to 6" incl. 0.007" 0.009"

HEXAGONS

To 3/4" incl. 0.004" 0.007"Over 3/4" to 1-1/2" incl. 0.005" 0.008"Over 1-1/2" to 2-1/2" incl. 0.006" 0.009"

SQUARES

To 3/4" incl. 0.005" 0.008"Over 3/4" to 1-1/2" incl. 0.006" 0.009"Over 1-1/2" to 2-1/2" incl. 0.007" 0.010"

FLATSWIDTH IN INCHES *The tolerances for flats apply to thickness as well as width.*

To 3/4" incl. 0.005" 0.009"Over 3/4" to 1-1/2" incl. 0.006" 0.011"Over 1-1/2" to 3" incl. 0.007" 0.013"Over 3" to 4" incl. 0.009" 0.017"Over 4" to 6" incl. 0.011" 0.021"

4130 NORM4140 ANN6150 ANN8740 ANN

NOTE 1. CG & RT Vac Melt Alloy Tolerances are the same as Stainless. See page 64.NOTE 2. DG&P & TG&P Finishes are: Plus or Minus .001"NOTE 3. CF/T equals same as Cold Draw TolerancesNOTE 4. HR/RT equals same as Hot Rolled TolerancesNOTE: ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES.

ROUNDS

4130 HT4330 NORM & TEMP4340 NORM & TEMP

52100 SPHERIODIZED ANN9310 NORM & TEMP

NITRIDINGD6AC NORM & TEMP

HY-TUF NORM & TEMPSize in inches

AIRCRAFT ALLOYRecommended Stock Removal

(Minimum requirement necessary to qualify for rejection)



(562) 802-2721

The following table provides minimum stock removal requirements, for Round, Flat, Hex and Square bars, toensure surfaces that are free of decarburization, seams, laps, cracks, pits and other injurious surface imperfections. These are based on various Industry Standards. Please consult these charts, prior to anythermal treatment.

Minimum Removal FromHot Rolled Size The Surface, Inches Cold Drawn Size(Inches) (Per Each Side) (Inches)– – Up to 1/2" Incl. .030" – – Up to 7/16" Incl.Over 1/2" to 3/4" Incl. .045" Over 7/16" to 11/16" Incl.Over 3/4" to 1" Incl. .060" Over 11/16" to 15/16" Incl.Over 1" to 1-1/2" Incl. .075" Over 15/16" to 1-7/16" Incl.Over 1-1/2" to 2" Incl. .090" Over 1-7/16" to 1-15/16" Incl.Over 2" to 2-1/2" Incl. .125" Over 1-15/16" to 2-7/16" Incl.Over 2-1/2" to 3-1/2" Incl. .156" Over 2-7/16" to 3-3/8" Incl.Over 3-1/2" to 4-1/2" Incl. .187" Over 3-3/8" to 4-3/8" Incl.Over 4-1/2" to 6" Incl. .250"Over 6" to 7-1/2" Incl. .312"Over 7-1/2" to 9" Incl. .375"

PRESSED (FORGED) ROUND BARSThe amount of metal to be removed from the surface of Carbon and Alloy Pressed Round Bars over 8" indiameter in order to obtain a finished size varies because consideration must be given to several factors, suchas manufacturing practice, size of bar, length and straightness. As a guide, the usual allowances for bars 8' to10' long are:

Diameters through 13". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2" on diameter, 1/4" on surfaceDiameters over 13" to 19" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5/8" on diameter, 5/16" on surface

CENTERLESS GROUND:ALL GROUND BAR SHOULD BE “DEFECT FREE” WITHIN THE STANDARD SIZE TOLERANCESOF ANY MANUFACTURING DEFECTS. IE: SEAMS, LAPS, AND CRACKS.



ROUGH TURNED:ALL “R.T.” SIZES ARE PRODUCED ON THE PLUS SIDE AND SHOULD BE DEFECT FREE ON SIZE.


NOTE: INSPECTION PRIOR TO ALTERING MATERIAL IS ADVISABLE.NOTE: IT IS NOT ADVISABLE TO TRY TO FINISH ON SIZE FROM THE SIZE PURCHASED.

ALLOY CONDITIONS*Physical Condition Surface ConditionA — As Forged 1 — Black as Forged or RolledB — As Rolled 2 — Pickled or Blast CleanedC — Annealed 3 — Rough Turned/ Smooth TurnedD — Normalized 4 — Cold Finished (Drawn)E — Normalized & Tempered 5 — Centerless Ground

6 — Turned, Ground and Polished

*E-52100 Spheriodized Annealed is Cond. E.*D6AC Normalized and Tempered is Cond. F.

E-4130 120 72

E-4130 H.T. 65 40

E-4140 110 66

E-4330 Mod 95 57

E-4340 95 57

E-4340 Mod “300M” 95 57

E-4620 V.M. 110 66

E-52100 65 40

MAN- PHOS- CHROM- MOLYB-AISI CARBON GANESE PHORUS SULFER SILICON NICKEL IUM DENUM COPPER OTHERS

E-4130 .28/.33 .40/.60 .025 .025 .15/.35 .25 .80/1.10 .15/.25 .35

E-4130 HT .28/.33 .40/.60 .025 .025 .15/.35 .25 .80/1.10 .15/.25 .35

E-4140 .38/.43 .75/1.0 .025 .025 .20/.35 .25 .80/1.10 .15/.25 .35

E-4330 .28/.33 .80/1.0 .015 .015 .20/.35 1.65/2.0 .75/.95 .35/.50 .35 V .05/.10

MOD V.M.

E-4340 .38/.43 .65/.85 .015 .008 .15/.35 1.65/2.0 .70/.90 .20/.30 .35

E-4340 V.M. .38/.43 .65/.85 .01 .01 .15/.35 1.65/2.0 .70/.90 .20/.30 .35

E-4340 .40/.43 .65/.90 .01 .008 1.45/1.80 1.65/2.0 .70/.95 .35/.45 .35 V .05/.10

MOD 300M

E-4620 V.M. .17/.22 .45/.60 .025 .025 .20/.35 1.65/2.00 .20 .20/.30 .35

E-52100 V.M. .98/1.10 .25/.45 .015 .015 .20/.35 .25 1.3/1.6 .08 .35

E-6150 V.M. .48/.53 .70/.90 .025 .025 .20/.35 .25 .80/1.10 .06 .35 V .15/.30

E-8740 .38/.43 .75/1.0 .025 .025 .20/.35 .40/.70 .40/.60 .20/.30 .35

E-9310 .07/.13 .40/.70 .025 .025 .20/.35 3.00/3.50 1.0/1.4 .08/.15 .35 B .001

E-9310 V.M. .07/.13 .40/.70 .015 .015 .20/.35 3.00/3.50 1.0/1.4 .08/.15 .35 B .001

Nitriding HT .38/.43 .50/.70 .025 .025 .20/.40 .25 1.4/1.8 .30/.40 .35 Al .95/1.30

Nitriding V.M. .38/.43 .50/.70 .015 .015 .20/.40 .25 1.4/1.8 .30/.40 .35 Al .95/1.30

H-11 .38/.43 .20/.40 .015 .015 .80/1.0 .25 4.75/5.25 1.2/1.4 .35 V .40/.60

Hy-Tuf .23/.28 1.2/1.5 .04 .04 1.3/1.7 1.65/2.0 .20/.40 .35/.45 .35

Hy-Tuf V.M. .23/.28 1.2/1.5 .01 .01 1.3/1.7 1.65/2.0 .20/.40 .35/.45 .35

D6AC .45/.48 .60/.90 .01 .01 .15/.30 .40/.70 .90/1.20 .90/1.10 .35 V .08/.15

9-4-30 .29/.34 .10/.35 .01 .01 .20 7.0/8.0 .90/1.10 .90/1.10 .35 V .06/.12

Co 4.25/4.75

CHEMICAL ANALYSES — Maximum Unless Indicated

The above chart is a compilation of Aerospace, ASTM, Federal and Military specifica-tions. It is for reference only and should not be used for design or specifications.

E-6150 100 60

E-8740 110 66

E-9310 80 49

Nitriding 83 51

H-11 75 45

Hy-Tuf 75 45

D6AC 80 49

9-4-30 75 45

MACHINABILITY RATINGS*ALLOY

% RELATIVE SPEEDBASED ON C-1212 AS

100% (165 SFM)

*These machinability ratios must be recognized as approximate values.

% RELATIVE SPEEDBASED ON

C-1212 AS 100%GRADE

APPROXIMATESURF. FT.PER MIN.

GRADE


AIRCRAFT ALLOYSTEELS


[email protected]

(562) 802-2721

ALU

MIN

UM

ALU

MIN

UM

ALUMINUMGRADES STOCKED


[email protected]

(562) 802-2721

Grade Si Fe Cu Mg Mn Cr Zn Ti Al Others

2011 .40 0.7 5.0/6.0 .30 Bal. Bi .2/.6 Pb .2/.62024 .50 .50 3.8/4.9 1.2/1.8 .30/.90 .10 .25 .15 Bal.

6061 .40/.80 0.7 .15/.40 .8/1.2 .15 .04/.35 .25 .15 Bal.

6262 .40/.80 0.7 .15/.40 .8/1.2 .15 .04/.14 .25 .15 Bal. Bi .4/.7 Pb .4/.77075 .40 .50 1.2/2.0 2.1/2.9 .30 .18/.28 5.1/6.1 .20 Bal. Ti + Zn .25

CF 6262 T-9 QQA-225/10, AMS-QQA-225/10, ASTM-B-211

EXT 6262 T-6511 ASTM-B-221

CF 7075 T-6 QQA-225/9, AMS-QQA-225/9,ASTM-B-211, AMS-4122


EXT 7075 T-6 QQA-200/11, AMS-QQA-200/11, ASTM-B-211, AMS-4154

EXT 7075 T-6511 QQA-200/11, AMS-QQA-200/11,ASTM-B-221, AMS-4169

CF 7075 T-73 QQA-225/9, AMS-QQA-225/9,CHEMS ONLY TO FOLLOWING:ASTM-B-211, AMS-4122

CF 7075 T-7351 QQA-225/9, AMS-QQA-225/9,CHEMS ONLY TO FOLLOWING:ASTM-B-211, AMS-4124


% RELATIVE SPEEDAPPROXIMATE BASED ON

GRADE SURF. FT. 2011 AS 100%

2011 - 1002024 - 906061 - 70-806262 - 1007075 - 75-85


MACHINABILITY RATINGSALUMINUM

Aluminum ChemistryMaximum Unless Indicated

SPECIFICATIONS SPECIFICATIONS

CF 2011 T-3 QQA-225/3, AMS-QQA-225/3,ASTM-B-211

CF 2024 T-4 QQA-225/6, AMS-QQA-225/6,ASTM- B-211, AMS-4120





CF-6061 T-6 QQA-225/8, AMS-QQA-225/8,ASTM-B-211, AMS-4117

CF-6061 T-651 QQA-225/8, AMS-QQA-225/8,ASTM-B-211, AMS-4117

EXT 6061 T-6 AMS-QQA-200/8, QQA-200/8,AMS-4150, ASTM-B-221

EXT 6061 T-6511 AMS-QQA-200/8, QQA-200/8,ASTM-B-221, AMS-4173

The above chart is a compilation of Aerospace, ASTM, Federal specifications.It is for reference only and should not be used for design or specifications.



EXTRUDEDALUMINUM


111

1.800.423.6651


(562) 802-2721

SIZE TYPE TEMPER WT/FT WT/BAR SIZE TYPE TEMPER WT/FT WT/BAR

1-3/16" 6061 T6511 1.302 15.6246262 T6511 1.300 15.600

1-1/4" 2024 T3511 1.474 17.6886061 T6511 1.442 17.3096262 T6511 1.442 17.3047075 T6511 1.486 17.8397075 T73511 1.486 17.839

1-5/16" 6061 T6511 1.590 19.0846262 T6511 1.588 19.056

1-3/8" 2024 T3511 1.840 22.0806061 T6511 1.745 20.9446262 T6511 1.745 20.9407075 T6511 1.800 20.944

1-7/16" 2024 T3511 1.950 23.4006061 T6511 1.908 22.8966262 T6511 1.905 22.860

1-1/2" 2024 T3511 2.123 25.4766061 T6511 2.077 24.9256262 T6511 2.076 24.9127075 T6511 2.140 25.6887075 T73511 2.140 25.688

1-9/16" 6061 T6511 2.253 27.0466262 T6511 2.250 27.000

1-5/8" 2024 T3511 2.560 30.7206061 T6511 2.437 29.2526262 T6511 2.435 29.2207075 T6511 2.510 29.252

1-11/16" 6061 T6511 2.633 31.5966262 T6511 2.625 31.500

1-3/4" 2024 T3511 2.889 34.6686061 T6511 2.827 33.9266262 T6511 2.826 33.9127075 T6511 2.913 34.9647075 T73511 2.913 34.964

1-13/16" 6061 T6511 3.032 36.392

1-7/8" 2024 T3511 3.310 39.7206061 T6511 3.245 38.9466262 T6511 3.244 38.928

7075 T6511 3.349 40.188

1-15/16" 6061 T6511 3.469 41.628

2" 2024 T3511 3.773 45.2766061 T6511 3.692 44.3116262 T6511 3.691 44.2927075 T6511 3.805 45.6687075 T73511 3.805 45.668

2-1/32" 6061 T6511 3.813 45.756

2-1/16" 6061 T6511 3.933 47.196

2-1/8" 2024 T3511 4.264 51.1686061 T6511 4.168 50.0237075 T73511 4.168 50.023

2-3/16" 6061 T6511 4.424 53.088

1/4" 6061 T6511 .0570 .694

5/16" 6061 T6511 .0900 1.084

3/8" 2024 T3511 .1328 1.5946061 T6511 .1300 1.560

7/16" 6061 T6511 .1770 2.124

1/2" 2024 T3511 .2360 2.8326061 T6511 .2308 2.7706262 T6511 .2306 2.7677075 T6511 .2379 2.8557075 T73511 .2379 2.855

9/16" 2024 T3511 .2985 3.5826061 T6511 .2921 3.5056262 T6511 .2919 3.5037075 T6511 .2985 3.582

5/8" 2024 T3511 .3685 4.4226061 T6511 .3606 4.3276262 T6511 .3604 4.3257075 T6511 .3684 4.4217075 T73511 .3684 4.421

11/16" 2024 T3511 .4459 5.3516061 T6511 .4369 5.2436262 T6511 .4361 5.2337075 T6511 .4369 5.243

3/4" 2024 T3511 .5307 6.3686061 T6511 .5193 6.2326262 T6511 .5190 6.2287075 T6511 .5355 6.4267075 T73511 .5355 6.426

13/16" 2024 T3511 .6229 7.4756061 T6511 .6104 7.3256262 T6511 .6091 7.3097075 T6511 .6103 7.324

7/8" 6061 T6511 .7068 8.4826262 T6511 .7064 8.4777075 T6511 .7310 8.4827075 T73511 .7310 8.482

15/16" 6061 T6511 .8114 9.7376262 T6511 .8110 9.732

1" 2024 T3511 .9433 11.3206061 T6511 .9232 11.0786262 T6511 .9227 11.0727075 T6511 .9514 11.4177075 T73511 .9514 11.417

1.010" 6061 T6511 .924 11.312

1-1/16" 2024 T3511 1.065 12.7806061 T6511 1.042 12.5066262 T6511 1.040 12.480

1-1/8" 2024 T3511 1.190 14.2806061 T6511 1.169 14.0386262 T6511 1.168 14.0167075 T6511 1.204 14.449

1-3/16" 2024 T3511 1.330 15.960

NOTE: ** INQUIRE

EXTRUDEDALUMINUM


112

1.800.423.6651

112

(562) 802-2721


4" 7075 T73511 15.223 182.676

4-1/8" 6061 T6511 15.710 188.520

4-1/4" 2024 T3511 17.050 204.6006061 T6511 16.697 200.3647075 T6511 17.210 206.5207075 T73511 17.210 206.520

4-3/8" 6061 T6511 17.650 211.800

4-1/2" 2024 T3511 19.100 229.2006061 T6511 18.690 224.2807075 T6511 19.266 231.1927075 T73511 19.266 231.192

4-5/8" 6061 T6511 19.780 237.360

4-3/4" 2024 T3511 21.310 255.7206061 T6511 20.858 250.2967075 T6511 21.500 258.0007075 T73511 21.500 258.000

5" 2024 T3511 23.580 282.9606061 T6511 23.080 276.9607075 T6511 23.785 285.4207075 T73511 23.785 285.420

5-1/8" 6061 T6511 24.280 291.360

5-1/4" 2024 T3511 26.000 312.0006061 T6511 25.480 305.7607075 T6511 26.260 315.120

5-1/2" 2024 T3511 28.540 342.4806061 T6511 27.930 335.1607075 T6511 28.820 345.840

5-3/4" 6061 T6511 30.570 366.8407075 T6511 31.500 378.000

6" **2024 T3 33.960 407.520**2024 T3511 33.960 407.520**6061 T6 33.230 398.760**6061 T6511 33.230 398.760**7075 T6511 34.251 411.012**7075 T6 34.251 411.012

6-1/8" **6061 T6 34.690 416.280**6061 T6511 34.690 416.280

6-1/4" **6061 T6 36.110 433.320**6061 T6511 36.110 433.320

6-1/2" **2024 T3511 39.850 478.200**2024 T3 39.850 478.200**6061 T6 39.000 468.000**6061 T6511 39.000 468.000**7075 T6 40.250 483.000**7075 T6511 40.250 483.000

6-3/4" **6061 T6 42.130 505.560**6061 T6511 42.130 505.560

7" **2024 T3511 46.210 554.520**2024 T3 46.210 554.520**6061 T6511 45.230 542.760**6061 T6 45.230 542.760

2-1/4" 2024 T3511 4.777 57.3246061 T6511 4.673 56.0826262 T6511 4.700 56.4007075 T6511 4.816 57.7997075 T73511 4.816 57.799

2-5/16" 6061 T6511 4.944 59.328

2-3/8" 2024 T3511 5.324 63.8886061 T6511 5.207 62.4867075 T73511 5.207 62.486

2-7/16" 6061 T6511 5.494 65.928

2-1/2" 2024 T3511 5.897 70.7646061 T6511 5.769 69.2386262 T6511 5.760 69.1207075 T6511 5.946 71.3577075 T73511 5.946 71.357

2-5/8" 2024 T3511 6.500 78.0006061 T6511 6.361 76.3337075 T6511 6.565 78.7807075 T73511 6.565 78.780

2-3/4" 2024 T3511 7.137 85.6446061 T6511 6.981 83.7776262 T6511 6.970 83.6407075 T6511 7.195 86.3417075 T73511 7.195 86.341

2-7/8" 6061 T6511 7.630 91.5667075 T73511 7.630 91.566

3" 2024 T3511 8.490 101.886061 T6511 8.308 99.7016262 T6511 8.295 99.5407075 T6511 8.562 102.7547075 T73511 8.562 102.754

3-1/8" 2024 T3511 9.200 110.4006061 T6511 9.015 108.182

3-1/4" 2024 T3511 9.960 119.5206061 T6511 9.750 117.0117075 T6511 10.07 120.8407075 T73511 10.07 120.840

3-3/8" 2024 T3511 10.750 129.0006061 T6511 10.515 126.180

3-1/2" 2024 T3511 11.560 138.7206061 T6511 11.308 135.6967075 T6511 11.655 139.8607075 T73511 11.655 139.860

3-5/8" 2024 T3511 12.400 148.8006061 T6511 12.130 145.560

3-3/4" 2024 T3511 13.250 159.0006061 T6511 12.980 155.7607075 T6511 13.400 160.8007075 T73511 13.400 160.800

4" 2024 T3511 15.100 181.2006061 T6511 14.770 177.2407075 T6511 15.223 182.676

FRY STEEL COMPANY

NOTE: ** INQUIRE

EXTRUDEDALUMINUM


113

1.800.423.6651


(562) 802-2721


7" **7075 T6511 46.620 559.440**7075 T6 46.620 559.440

7-1/2" **6061 T6511 52.100 625.200**6061 T6 52.100 625.200

8" **2024 T3511 60.380 724.560**2024 T3 60.380 724.560**6061 T6511 59.080 708.960**6061 T6 59.080 708.960**7075 T6511 60.890 730.680**7075 T6 60.890 730.680

8-1/4" **6061 T6511 62.900 754.800**6061 T6 62.900 754.800

8-1/2" **6061 T6511 66.780 801.360**6061 T6 66.780 801.360

9" **6061 T6511 74.890 898.680**6061 T6 74.890 898.680**7075 T6511 77.180 926.160**7075 T6 77.180 926.160

9-1/2" **6061 T6511 84.430 1013.160**6061 T6 84.430 1013.160**7075 T6511 85.990 1031.880**7075 T6 85.990 1031.880

10" **6061 T6511 92.440 1109.280**6061 T6 92.440 1109.280

10" **7075 T6511 95.260 1143.120**7075 T6 95.260 1143.120

10-1/2" **6061 T6511 101.900 1222.800**6061 T6 101.900 1222.800

11" **6061 T6511 112.170 1346.040**6061 T6 112.170 1346.040

12" **6061 T6511 133.110 1597.320**6061 T6 133.110 1597.320**7075 T6511 137.100 1645.200**7075 T6 137.100 1645.200

13" **6061 T6511 156.000 1872.000**6061 T6 156.000 1872.000

14" **6061 T6511 181.170 2174.040**6061 T6 181.170 2174.040

15" **6061 T6511 208.800 2505.600**6061 T6 208.800 2505.600

16" **6061 T6511 236.800 2841.600**6061 T6 236.800 2841.600

17" **6061 T6511 267.000 3204.000**6061 T6 267.000 3204.000

18" **6061 T6511 300.000 3600.000**6061 T6 300.000 3600.000

COLD FINISHEDALUMINUM



[email protected]

(562) 802-2721


3/8" 2024 T4 .1328 1.5946061 T6 .1301 1.5616262 T9 .1297 1.5507075 T6 .1341 1.609

.380" 2011 T3 .1389 1.667

25/64" 2011 T3 .1466 1.7596061 T6 .1409 1.691

13/32" 2011 T3 .1589 1.9072024 T4 .1558 1.8706061 T6 .1526 1.831

7/16" 2011 T3 .1841 2.2092024 T4 .1805 2.1666061 T6 .1769 2.1236262 T9 .1766 2.1197075 T6 .1823 2.188

.4425" 2011 T3 .1883 2.260

29/64" 2011 T3 .1974 2.3696061 T6 .1897 2.276

15/32" 2011 T3 .2115 2.5382024 T4 .2074 2.4896061 T6 .2032 2.438

31/64" 6061 T651 .2664 3.197

1/2" 2011 T3 .2407 2.8882024 T4 .2360 2.8322024 T851 .2360 2.8326061 T651 .2308 2.7706262 T9 .2306 2.7677075 T6 .2379 2.8557075 T651 .2379 2.8557075 T73 .2379 2.796

.505" 2011 T3 .2450 2.940

33/64" 2011 T3 .2558 3.0706061 T651 .2458 2.950

17/32" 2011 T3 .2717 3.2602024 T4 .2664 3.197

9/16" 2011 T3 .3045 3.6542024 T4 .2985 3.5826061 T651 .2921 3.5056262 T9 .2919 3.5037075 T6 .3015 3.6187075 T651 .3015 3.618

19/32" 2011 T3 .3391 4.0696061 T651 .3258 3.910

5/8" 2011 T3 .3758 4.5102024 T351 .3684 4.4272024 T4 .3685 4.4222024 T851 .3689 4.4276061 T651 .3606 4.3276262 T9 .3604 4.3257075 T6 .3721 4.4657075 T651 .3721 4.4657075 T7351 .3721 4.452

3/32" 2011 T3 .0082 .098

7/64" 2011 T3 .0115 .138

1/8" 2011 T3 .0151 .1812024 T4 .0148 .1786061 T6 .0145 .1746262 T9 .0140 .168

.130" 2011 T3 .0162 .194

9/64" 2011 T3 .0191 .2296061 T6 .0183 .220

5/32" 2011 T3 .0234 .2816061 T6 .0225 .270

11/64" 2011 T3 .0284 .341

3/16" 2011 T3 .0338 .4062024 T4 .0332 .3986061 T6 .0325 .3906262 T9 .0320 .384

.1925" 2011 T3 .0356 .427

13/64" 2011 T3 .0396 .4756061 T6 .0380 .456

7/32" 2011 T3 .0461 .5532024 T4 .0452 .5426061 T6 .0443 .532

15/64" 2011 T3 .0529 .635

1/4" 2011 T3 .0601 .7212024 T4 .0590 .7086061 T6 .0578 .6946262 T9 .0577 .6927075 T6 .0595 .7147075 T73 .0595 .714

.255" 2011 T3 .0625 .750

17/64" 2011 T3 .0677 .8126061 T6 .0650 .780

9/32" 2011 T3 .0760 .9122024 T4 .0745 .8946061 T6 .0730 .876

19/64" 2011 T3 .0846 1.015

5/16" 2011 T3 .0940 1.1282024 T4 .0922 1.1066061 T6 .0903 1.0846262 T9 .0900 1.0807075 T6 .0931 1.117

.318" 2011 T3 .0969 1.163

21/64" 2011 T3 .1034 1.2416061 T6 .0993 1.192

11/32" 2011 T3 .1138 1.3662024 T4 .1116 1.3396061 T6 .1094 1.313

23/64" 2011 T3 .1243 1.492

3/8" 2011 T3 .1355 1.626







(562) 802-2721


1-1/16" 6061 T651 1.042 12.506

1-1/8" 2011 T3 1.217 14.6042024 T351 1.193 14.3166061 T651 1.169 14.0386262 T9 1.168 14.0167075 T651 1.204 14.4497075 T7351 1.204 14.400

1-3/16" 2011 T3 1.357 16.2842024 T351 1.330 15.9606061 T651 1.302 15.624

1-1/4" 2011 T3 1.503 18.0362024 T351 1.474 17.6882024 T851 1.474 17.6886061 T651 1.442 17.3096262 T9 1.442 17.3047075 T651 1.486 17.8397075 T7351 1.486 17.760

1-5/16" 2011 T3 1.657 19.8842024 T351 1.625 19.5006061 T651 1.590 19.0847075 T651 1.641 19.692

1-3/8" 2011 T3 1.819 21.8282024 T351 1.783 21.3966061 T651 1.745 20.9446262 T9 1.745 20.9407075 T651 1.801 21.6127075 T7351 1.801 21.600

1-7/16" 2011 T3 1.988 23.8562024 T351 1.949 23.3886061 T651 1.908 22.896

1-1/2" 2011 T3 2.165 25.9802024 T351 2.122 25.4642024 T851 2.122 25.4646061 T651 2.077 24.9256262 T9 2.076 24.9127075 T651 2.140 25.6887075 T7351 2.140 25.680

1-9/16" 2011 T3 2.349 28.1882024 T351 2.303 27.6366061 T651 2.253 27.046

1-5/8" 2011 T3 2.541 30.4922024 T351 2.491 29.8926061 T651 2.437 29.2526262 T9 2.436 29.2327075 T651 2.515 30.188

1-11/16" 2011 T3 2.740 32.8806061 T651 2.633 31.596

1-3/4" 2011 T3 2.947 35.3642024 T351 2.889 34.6682024 T851 2.889 34.6686061 T651 2.827 33.9266262 T9 2.826 33.9127075 T651 2.913 34.9647075 T7351 2.913 34.920

.630" 2011 T3 .3820 4.584

41/64" 2011 T3 .3950 4.740

21/32" 2011 T3 .4144 4.9736061 T651 .3980 4.776

11/16" 2011 T3 .4548 5.4582024 T351 .4460 5.3526061 T651 .4369 5.2436262 T9 .4361 5.2337075 T651 .4500 5.400

23/32" 2011 T3 .4969 5.9636061 T651 .4773 5.728

3/4" 2011 T3 .5413 6.4962024 T351 .5306 6.3672024 T4 .5306 6.3672024 T851 .5312 6.3676061 T651 .5193 6.2326262 T9 .5190 6.2287075 T651 .5355 6.4267075 T7351 .5355 6.420

.755" 2011 T3 .5485 6.582

25/32" 2011 T3 .5864 7.0376061 T651 .5643 6.772

13/16" 2011 T3 .6353 7.6242024 T351 .6228 7.4746061 T651 .6103 7.3246262 T9 .6091 7.3097075 T651 .6290 7.548

27/32" 2011 T3 .6840 8.2086061 T651 .6580 7.896

7/8" 2011 T3 .7366 8.8392024 T351 .7220 8.6642024 T851 .7221 8.6646061 T651 .7068 8.4826262 T9 .7064 8.4777075 T651 .7292 8.7507075 T7351 .7292 8.760

29/32" 2011 T3 .7900 9.480

15/16" 2011 T3 .8458 10.1502024 T351 .8290 9.9486061 T651 .8114 9.7376262 T9 .8110 9.7327075 T651 .8370 10.044

31/32" 2011 T3 .9017 10.280

1" 2011 T3 .9622 11.5462024 T351 .9430 11.3162024 T851 .9430 11.3166061 T651 .9232 11.0786262 T9 .9227 11.0727075 T651 .9514 11.4177075 T7351 .9514 11.400

1-1/16" 2011 T3 1.086 13.0322024 T351 1.064 12.768






[email protected]

(562) 802-2721


2-5/8" 7075 T651 6.565 78.780

2-3/4" 2011 T3 7.280 87.3602024 T351 7.136 85.6322024 T851 7.136 85.6326061 T651 6.981 83.7776262 T9 6.978 83.7367075 T651 7.195 86.341

2-7/8" 2011 T3 7.954 95.4482024 T351 7.797 93.5646061 T651 7.630 91.5606262 T9 7.620 91.440

3" 2011 T3 8.660 103.9202024 T351 8.486 101.8322024 T851 8.486 101.8326061 T651 8.308 99.7016262 T9 8.304 99.6487075 T651 8.562 102.7547075 T7351 8.562 102.600

3-1/8" 2011 T3 9.400 112.8002024 T351 9.214 110.5686061 T651 9.029 108.3487075 T651 9.214 110.568

3-1/4" 2024 T351 9.966 119.5922024 T851 9.970 119.6406061 T651 9.750 117.0107075 T651 10.065 120.780

3-3/8" 2011 T3 10.960 131.5202024 T351 10.740 128.8806061 T651 10.530 126.3607075 T651 10.750 129.000

3-1/2" 2011 T3 11.780 141.3602024 T351 11.550 138.6006061 T651 11.308 135.6967075 T651 11.655 139.860

3-5/8" 2024 T351 12.400 148.8006061 T651 12.140 145.6807075 T651 12.520 150.240

3-3/4" 2011 T3 13.530 162.3602024 T351 13.260 159.1202024 T851 13.260 159.1206061 T651 12.980 155.7607075 T651 13.397 160.764

3-7/8" 2011 T3 14.450 173.4002024 T351 14.170 170.040

4" 2024 T351 15.090 181.0806061 T651 14.770 177.2407075 T651 15.223 182.676

4-1/4" 2024 T351 17.030 204.3606061 T651 16.697 200.3647075 T7351 17.170 206.040

4-1/2" 2011 T3 19.480 233.7602024 T351 19.100 229.2006061 T651 18.690 224.280

1-13/16" 2011 T3 3.161 37.9322024 T351 3.099 37.1886061 T651 3.032 36.392

1-7/8" 2011 T3 3.383 40.5962024 T351 3.316 39.7926061 T651 3.245 38.9466262 T9 3.244 38.9287075 T651 3.349 40.1957075 T7351 3.349 40.080

1-15/16" 2011 T3 3.611 43.332

2" 2011 T3 3.849 46.1882024 T351 3.773 45.2762024 T851 3.773 45.2766061 T651 3.692 44.3116262 T9 3.691 44.2927075 T651 3.805 45.6687075 T7351 3.805 45.600

2-1/16" 2011 T3 4.094 49.128

2-1/8" 2011 T3 4.346 52.1522024 T351 4.260 51.1206061 T651 4.168 50.0236262 T9 4.166 49.9927075 T651 4.303 51.6367075 T7351 4.303 51.480

2-3/16" 2011 T3 4.606 55.2726061 T651 4.424 53.088

2-1/4" 2011 T3 4.872 58.4642024 T351 4.776 57.3126061 T651 4.673 56.0826262 T9 4.671 56.0527075 T651 4.816 57.7997075 T7351 4.816 57.720

2-5/16" 2011 T3 5.147 61.7646061 T651 4.944 59.328

2-3/8" 2011 T3 5.427 65.1242024 T351 5.320 63.8406061 T651 5.207 62.4866262 T9 5.212 62.5447075 T651 5.373 64.481

2-7/16" 2011 T3 5.720 68.6406061 T651 5.494 65.928

2-1/2" 2011 T3 6.015 72.1802024 T351 5.896 70.7522024 T851 5.896 70.7526061 T651 5.769 69.2386262 T9 5.775 69.3007075 T651 5.946 71.3577075 T7351 5.946 71.280

2-9/16" 6061 T651 6.068 72.826

2-5/8" 2011 T3 6.631 79.5722024 T351 6.500 78.0006061 T651 6.361 76.3336262 T9 6.350 76.200



5-1/4" 6061 T651 25.480 305.76

5-1/2" 6061 T651 29.730 335.160

6" **2024 T351 33.950 407.400**2024 T4 33.950 407.400

7" **2024 T351 46.210 554.520**2024 T4 46.210 554.520

8" **2024 T351 60.380 724.560**2024 T4 60.380 724.560

4-1/2" 7075 T651 19.266 231.1927075 T7351 19.266 230.880

4-3/4" 2011 T3 21.710 260.5202024 T351 21.280 255.3606061 T651 20.858 250.2967075 T7351 21.440 257.280

5" 2011 T3 24.050 288.6002024 T351 23.580 282.9606061 T651 23.080 276.9607075 T651 23.785 285.420





(562) 802-2721


NOTE: ** INQUIRE






118

(562) 802-2721


7/8" 2024 T351 .7960 9.5522024 T851 .7960 9.5526061 T651 .7803 9.3646262 T9 .7809 9.3707075 T651 .8040 9.648

15/16" 2011 T3 .9327 11.1926061 T651 .8959 10.7516262 T9 .8965 10.758

1" 2011 T3 1.061 12.7322024 T351 1.040 12.4802024 T851 1.040 12.4806061 T651 1.019 12.2346262 T9 1.020 12.2407075 T651 1.050 12.608

1-1/16" 2011 T3 1.197 14.364

1-1/8" 2011 T3 1.343 16.1162024 T351 1.316 15.7926061 T651 1.290 15.4806262 T9 1.290 15.490

1-3/16" 2011 T3 1.496 17.952

1-1/4" 2011 T3 1.658 19.8962024 T351 1.625 19.5002024 T851 1.626 19.5126061 T651 1.593 19.1166262 T9 1.593 19.1257075 T651 1.641 19.699

1-5/16" 2011 T3 1.828 21.936

1-3/8" 2011 T3 2.006 24.0722024 T351 1.966 23.5926061 T651 1.925 23.1006262 T9 1.928 23.140

1-7/16" 2011 T3 2.193 26.316

1-1/2" 2011 T3 2.387 28.6442024 T351 2.340 28.0802024 T851 2.340 28.0806061 T651 2.293 27.5166262 T9 2.295 27.5407075 T651 2.364 28.386

1-5/8" 2011 T3 2.802 33.6242024 T351 2.746 32.9526061 T651 2.688 32.256

1-3/4" 2011 T3 3.250 39.0002024 T351 3.186 38.2322024 T851 3.186 38.2326061 T651 3.121 37.4527075 T7351 3.220 38.640

1-7/8" 2024 T351 3.656 43.872

2" 2011 T3 4.245 50.9402024 T351 4.161 49.9322024 T851 4.160 49.9206061 T651 4.077 48.924

2-1/4" 2011 T3 5.373 64.476

1/8" 2011 T3 .0166 .199

3/16" 2011 T3 .0374 .449

1/4" 2011 T3 .0663 .7962024 T4 .0650 .7806061 T6 .0636 .7637075 T6 .0657 .788

5/16" 2011 T3 .1037 1.2442024 T4 .1018 1.2226061 T6 .0997 1.1967075 T6 .1027 1.232

3/8" 2011 T3 .1492 1.7902024 T4 .1463 1.7566061 T6 .1460 1.7527075 T6 .1477 1.772

7/16" 2011 T3 .2032 2.4382024 T4 .1993 2.3926061 T6 .1952 2.3427075 T6 .2012 2.414

1/2" 2011 T3 .2652 3.1822024 T351 .2600 3.1202024 T851 .2600 3.1206061 T651 .2548 3.0586262 T9 .2550 3.0607075 T651 .2626 3.1517075 T73 .2630 3.156

9/16" 2011 T3 .3358 4.0302024 T351 .3290 3.9486061 T651 .3226 3.8716262 T9 .3285 3.9427075 T651 .3330 3.996

5/8" 2011 T3 .4144 4.9732024 T351 .4060 4.8722024 T851 .4060 4.8726061 T651 .3981 4.7776262 T9 .3984 4.7807075 T651 .4103 4.9247075 T7351 .4100 4.920

11/16" 2011 T3 .5016 6.0192024 T351 .4910 5.8926061 T651 .4819 5.7836262 T9 .4821 5.785

3/4" 2011 T3 .5968 7.1622024 T351 .5850 7.0202024 T851 .5850 7.0206061 T651 .5733 6.8806262 T9 .5738 6.8857075 T651 .5909 7.0917075 T7351 .5900 7.080

13/16" 2011 T3 .7006 8.4072024 T351 .6860 8.2326061 T651 .6730 8.0766262 T9 .6734 8.0807075 T651 .6936 8.323

7/8" 2011 T3 .8123 9.748





119

1.800.423.6651


(562) 802-2721


2-1/2” 2024 T351 6.500 78.0006061 T651 6.365 76.380

2-1/4" 2024 T351 5.267 63.2046061 T651 5.162 61.944

2-1/2" 2011 T3 6.631 79.572

SQUARESSTOCKED IN 12' R/L


1/4" 2011 T3 .0770 .9242024 T4 .0752 .9026061 T6 .0737 .884

5/16" 6061 T6 .1149 1.379

3/8" 2011 T3 .1723 2.0682024 T4 .1688 2.0266061 T6 .1654 1.985

7/16" 6061 T6 .2253 2.704

1/2" 2011 T3 .3063 3.6762024 T351 .3000 3.6002024 T851 .3000 3.6006061 T651 .2940 3.5287075 T651 .3030 3.6367075 T73 .3030 3.636

5/8" 2011 T3 .4786 5.7432024 T351 .4690 5.6286061 T651 .4594 5.5137075 T651 .4734 5.681

3/4" 2011 T3 .6894 8.2732024 T351 .6750 8.1002024 T851 .6760 8.1126061 T651 .6615 7.9387075 T651 .6817 8.1807075 T7351 .6830 8.196

7/8" 2011 T3 .9380 11.2566061 T651 .9011 10.813

1" 2011 T3 1.225 14.7002024 T351 1.200 14.400

6061 T651 1.176 14.1121" 2024 T851 1.200 14.400

7075 T651 1.212 14.544

1-1/8" 2011 T3 1.550 18.600

1-1/4" 2011 T3 1.915 22.9802024 T351 1.877 22.5242024 T851 1.877 22.5246061 T651 1.837 22.0507075 T651 1.893 22.7237075 T7351 1.900 22.800

1-1/2" 2011 T3 2.760 33.1202024 T351 2.702 32.4242024 T851 2.700 32.4006061 T651 2.646 31.7527075 T651 2.727 32.724

1-3/4" 6061 T651 3.603 43.2367075 T651 3.714 44.568

2" 2024 T351 4.804 57.6482024 T851 4.800 57.6006061 T651 4.704 56.4487075 T651 4.848 58.176

2-1/4" 2024 T351 6.080 72.9606061 T651 5.958 71.496

2-1/2" 2024 T351 7.507 90.0846061 T651 7.350 88.200

3" 2024 T351 10.810 129.7206061 T651 10.584 127.008

4" 2024 T351 19.210 230.520

EXTRUDEDALUMINUM



120

(562) 802-2721


1-1/8" 6061 T6511 1.290 15.4806262 T6511 1.287 15.444

1-1/4" 2024 T3511 1.626 19.5126061 T6511 1.593 19.1166262 T6511 1.588 19.0567075 T6511 1.642 19.704

1-3/8" 6061 T6511 1.925 23.100

1-1/2" 2024 T3511 2.341 28.0926061 T6511 2.293 27.5166262 T6511 2.287 27.4447075 T6511 2.364 28.368

1-5/8" 6061 T6511 2.688 32.256

1-3/4" 6061 T6511 3.121 37.452

2" 6061 T6511 4.077 48.924

2-1/4" 6061 T6511 5.164 61.968

2-1/2" 6061 T6511 6.365 76.380

2-3/4" 6061 T6511 7.710 92.520

3" 6061 T6511 9.170 110.040

1/2" 2024 T3511 .2600 3.1206061 T6511 .2548 3.0586262 T6511 .2540 3.0487075 T6511 .2620 3.151

5/8" 2024 T3511 .4060 4.8766061 T6511 .3981 4.7776262 T6511 .3970 4.7647075 T6511 .4100 4.924

3/4" 2024 T3511 .5850 7.0206061 T6511 .5733 6.8806262 T6511 .5720 6.8647075 T6511 .5900 7.091

7/8" 2024 T3511 .7960 9.5566061 T6511 .7803 9.3646262 T6511 .7781 9.3377075 T6511 .8040 9.650

1" 2024 T3511 1.041 12.4926061 T6511 1.020 12.2646262 T6511 1.017 12.2047075 T6511 1.051 12.612

1-1/16" 6061 T6511 1.150 13.800





1-1/4" 7075 T6511 1.894 22.7237075 T73511 1.895 22.740

1-1/2" 2024 T3511 2.700 32.4006061 T6511 2.646 31.7527075 T6511 2.727 32.7247075 T73511 2.729 32.748

1-3/4" 6061 T6511 3.604 43.2487075 T73511 3.714 44.568

2" 2024 T3511 4.800 57.6006061 T6511 4.704 56.4487075 T6511 4.848 58.1767075 T73511 4.852 58.224

2-1/4" 6061 T6511 5.958 71.496

2-1/2" 2024 T3511 7.500 90.0006061 T6511 7.350 88.2007075 T6511 7.575 90.900

2-3/4" 6061 T6511 8.904 106.848

3" 2024 T3511 10.800 129.6006061 T6511 10.584 127.0087075 T6511 10.910 130.920

3-1/2" 6061 T6511 14.420 173.0407075 T6511 14.850 178.200

3-3/4" 6061 T6511 16.550 198.600

1/4" 6061 T6511 .0737 .884

3/8" 6061 T6511 .1654 1.985

1/2" 2024 T3511 .2990 3.5886061 T6511 .2940 3.5287075 T6511 .3030 3.6367075 T73511 .3030 3.636

9/16" 6061 T6511 .3725 4.470

5/8" 2024 T3511 .4670 5.6046061 T6511 .4594 5.5137075 T6511 .4734 5.681

11/16" 6061 T6511 .5563 6.676

3/4" 2024 T3511 .6740 8.0886061 T6511 .6615 7.9387075 T6511 .6817 8.8107075 T73511 .6830 8.196

13/16" 6061 T6511 .7772 9.326

7/8" 6061 T6511 .9011 10.813

1" 2024 T3511 1.200 14.4006061 T6511 1.176 14.1127075 T6511 1.212 14.5447075 T73511 1.213 14.556

1-1/4" 2024 T3511 1.870 22.4406061 T6511 1.837 22.050



EXTRUDEDALUMINUM

SQUARES-ContinuedSTOCKED IN 12' R/L

121

1.800.423.6651


(562) 802-2721


8" 6061 T6511 59.080 708.9604" 2024 T3511 19.200 230.4006061 T6511 18.820 225.8407075 T6511 19.390 232.680

5" 2024 T3511 30.000 360.0006061 T6511 29.400 352.8007075 T6511 30.300 363.600

6" 2024 T3511 43.200 518.4006061 T6511 42.340 508.0807075 T6511 43.630 523.560

EXTRUDEDALUMINUM



122

(562) 802-2721


5/16" x1-1/4" 6061 T6511 .4594 5.513

1-1/2" 6061 T6511 .5513 6.616

2" 6061 T6511 .7350 8.820

3" 6061 T6511 1.102 13.230

4" 6061 T6511 1.470 17.640

5" 6061 T6511 1.839 22.068

6" 6061 T6511 2.207 26.484

3/8" x 1/2" 6061 T6511 .2205 2.646

5/8" 6061 T6511 .2723 3.268

3/4" 6061 T6511 .3308 3.970

1" 6061 T6511 .4410 5.292

7075 T6511 .4545 5.454

1-1/4" 6061 T6511 .5513 6.616

1-1/2" 6061 T6511 .6615 7.938

7075 T6511 .6817 8.180

1-3/4" 6061 T6511 .7724 9.269

2" 6061 T6511 .8820 10.584

7075 T6511 .9089 10.907

2-1/4" 6061 T6511 .9932 11.918

2-1/2" 6061 T6511 1.102 13.230

3" 6061 T6511 1.323 15.876

7075 T6511 1.363 16.362

3-1/2" 6061 T6511 1.543 18.516

4" 6061 T6511 1.764 21.168

7075 T6511 1.818 21.816

5" 6061 T6511 2.205 26.460

6" 6061 T6511 2.646 31.752

8" 6061 T6511 3.531 42.372

1/2" x 5/8" 6061 T6511 .3675 4.410

3/4" 6061 T6511 .4410 5.292

1" 6061 T6511 .5880 7.056

7075 T6511 .6060 7.272

7075 T73511 .6066 7.279

1-1/4" 6061 T6511 .7350 8.820

1-1/2" 6061 T6511 .8820 10.582

7075 T6511 .9089 10.907

7075 T73511 .9098 10.918

1-3/4" 6061 T6511 1.029 12.348

2" 6061 T6511 1.176 14.112

1/8" x 1/2" 6061 T6511 .0728 .874

5/8" 6061 T6511 .0909 1.091

3/4" 6061 T6511 .1103 1.324

1" 6061 T6511 .1470 1.764

1-1/4" 6061 T6511 .1815 2.178

1-1/2" 6061 T6511 .2205 2.646

2" 6061 T6511 .2940 3.528

2-1/2" 6061 T6511 .3750 4.500

3" 6061 T6511 .4357 5.228

4" 6061 T6511 .5810 6.972

3/16"x 1/2" 6061 T6511 .1103 1.324

3/4" 6061 T6511 .1654 1.985

1" 6061 T6511 .2205 2.646

1-1/4" 6061 T6511 .2757 3.308

1-1/2" 6061 T6511 .3308 3.970

1-3/4" 6061 T6511 .3864 4.637

2" 6061 T6511 .4410 5.292

2-1/2" 6061 T6511 .5513 6.616

3" 6061 T6511 .6615 7.938

4" 6061 T6511 .8828 10.594

1/4" x 1/2" 6061 T6511 .1470 1.764

5/8" 6061 T6511 .1814 2.177

3/4" 6061 T6511 .2205 2.646

1" 6061 T6511 .2940 3.528

1-1/4" 6061 T6511 .3675 4.410

1-1/2" 6061 T6511 .4410 5.292

1-3/4" 6061 T6511 .5145 6.174

2" 6061 T6511 .5880 7.056

2-1/4" 6061 T6511 .6615 7.938

2-1/2" 6061 T6511 .7350 8.820

3" 6061 T6511 .8820 10.584

3-1/2" 6061 T6511 1.029 12.348

4" 6061 T6511 1.176 14.112

5" 6061 T6511 1.470 17.640

6" 6061 T6511 1.764 21.168

8" 6061 T6511 2.354 28.248

5/16" x1/2" 6061 T6511 .1814 2.177

3/4" 6061 T6511 .2756 3.307

1" 6061 T6511 .3675 4.410



EXTRUDEDALUMINUM


123

1.800.423.6651


(562) 802-2721


3/4" x 1-1/2" 7075 T6511 1.363 16.356

7075 T73511 1.365 16.380

1-3/4" 6061 T6511 1.545 18.540

2" 6061 T6511 1.764 21.168

7075 T6511 1.818 21.816

7075 T73511 1.820 21.840

2-1/2" 6061 T6511 2.205 26.460

7075 T6511 2.272 27.264

3" 6061 T6511 2.646 31.752

7075 T6511 2.727 32.724

3-1/2" 6061 T6511 3.090 37.080

7075 T6511 3.181 38.172

4" 6061 T6511 3.528 42.336

7075 T6511 3.636 43.632

5" 6061 T6511 4.410 52.920

6" 6061 T6511 5.292 63.504

7075 T6511 5.454 65.448

8" 6061 T6511 7.062 84.774

10" 6061 T6511 8.828 105.936

12" 6061 T6511 10.590 127.080

7/8" x 1" 6061 T6511 1.023 12.276

1-1/2" 6061 T6511 1.545 18.540

2" 6061 T6511 2.060 24.720

1" x 1-1/4" 2024 T3511 1.500 18.000

6061 T6511 1.470 17.640

1-1/2" 2024 T3511 1.802 21.624

6061 T6511 1.764 21.168

7075 T6511 1.818 21.816

7075 T73511 1.820 21.840

1-3/4" 2024 T3511 2.102 25.224

6061 T6511 2.059 24.708

2" 2024 T3511 2.402 28.824

6061 T6511 2.352 28.224

7075 T6511 2.424 29.088

7075 T73511 2.426 29.112

2-1/4" 2024 T3511 2.703 32.436

6061 T6511 2.648 31.776

2-1/2" 2024 T3511 3.003 36.036

6061 T6511 2.940 35.280

1/2" x 2" 7075 T6511 1.212 14.544

7075 T73511 1.213 14.556

2-1/4" 6061 T6511 1.324 15.890

2-1/2" 6061 T6511 1.470 17.640

7075 T6511 1.515 18.180

2-3/4" 6061 T6511 1.617 19.404

3" 6061 T6511 1.764 21.168

7075 T6511 1.818 21.816

3-1/2" 6061 T6511 2.058 24.696

4" 6061 T6511 2.352 28.224

7075 T6511 2.424 29.088

5" 6061 T6511 2.942 35.312

6" 6061 T6511 3.528 42.336

7075 T6511 3.636 43.632

7" 6061 T6511 4.120 49.440

8" 6061 T6511 4.778 57.336

10" 6061 T6511 5.885 70.620

12" 6061 T6511 7.062 84.744

5/8" x 3/4" 6061 T6511 .5447 6.536

1" 6061 T6511 .7350 8.820

7075 T73511 .7580 9.096

1-1/4" 6061 T6511 .9188 11.026

1-1/2" 6061 T6511 1.1025 13.230

7075 T73511 1.137 13.644

1-3/4" 6061 T6511 1.287 15.450

2" 6061 T6511 1.470 17.640

7075 T73511 1.516 18.192

2-1/2" 6061 T6511 1.840 22.080

3" 6061 T6511 2.205 26.460

3-1/2" 6061 T6511 2.575 30.900

4" 6061 T6511 2.940 35.280

4-1/2" 6061 T6511 3.309 39.708

5" 6061 T6511 3.680 44.160

6" 6061 T6511 4.357 52.284

3/4" x 1" 6061 T6511 .8820 10.584

7075 T6511 .9089 10.907

7075 T73511 .9098 10.918

1-1/4" 6061 T6511 1.102 13.230

1-1/2" 6061 T6511 1.323 15.876



EXTRUDEDALUMINUM



124

(562) 802-2721


1-1/4"x 4" 7075 T73511 6.066 72.792

4-1/2" 6061 T6511 6.750 81.000

5" 2024 T3511 7.263 87.156

6061 T6511 7.263 87.156

6" 2024 T3511 9.100 109.200

6061 T6511 8.715 104.580

7075 T6511 9.098 109.176

7" 7075 T6511 10.610 127.320

8" 6061 T6511 11.770 141.240

7075 T6511 12.130 145.560

10" 6061 T6511 14.710 176.520

12" 6061 T6511 17.660 211.920

1-1/2"x 2" 2024 T3511 3.600 43.200

6061 T6511 3.528 42.336

7075 T6511 3.636 43.632

7075 T73511 3.639 43.668

2-1/2" 2024 T3511 4.500 54.000

6061 T6511 4.410 52.920

7075 T6511 4.555 54.600

3" 2024 T3511 5.400 64.800

6061 T6511 5.292 63.504

7075 T6511 5.450 65.400

7075 T73511 5.459 65.508

3-1/2" 6061 T6511 6.179 74.148

7075 T6511 6.490 77.880

4" 2024 T3511 7.210 86.520

6061 T6511 7.056 84.672

7075 T6511 7.270 87.240

7075 T73511 7.279 87.348

5" 2024 T3511 9.010 108.120

6061 T6511 8.820 105.840

7075 T6511 9.090 109.080

6" 2024 T3511 10.810 129.720

6061 T6511 10.580 126.960

7075 T6511 10.915 130.920

7" 6061 T6511 12.360 148.320

8" 6061 T6511 14.120 169.440

10" 6061 T6511 17.660 211.920

12" 6061 T6511 21.190 254.280

1" x 2-1/2" 7075 T6511 3.030 36.360

3" 2024 T3511 3.604 43.248

6061 T6511 3.528 42.336

7075 T6511 3.636 43.632

7075 T73511 3.639 43.668

3-1/2" 2024 T3511 4.204 50.448

6061 T6511 4.140 49.680

7075 T6511 4.240 50.880

4" 2024 T3511 4.805 57.660

6061 T6511 4.704 56.448

7075 T6511 4.848 58.176

7075 T73511 4.852 58.224

4-1/2" 6061 T6511 5.300 63.600

5" 6061 T6511 5.880 70.560

5-1/2" 6061 T6511 6.480 77.760

6" 2024 T3511 7.207 86.484

6061 T6511 7.056 84.672

7075 T6511 7.272 87.264

8" 6061 T6511 9.417 113.004

10" 6061 T6511 11.080 132.960

12" 6061 T6511 14.130 169.560

1-1/4"x 1-1/2" 6061 T6511 2.205 26.460

2" 2024 T3511 3.003 36.036

6061 T6511 2.990 35.280

7075 T6511 3.030 36.360

7075 T73511 3.033 36.396

2-1/4" 6061 T6511 3.311 39.732

2-1/2" 2024 T3511 3.750 45.000

6061 T6511 3.675 44.100

7075 T6511 3.787 45.444

3" 2024 T3511 4.500 54.000

6061 T6511 4.410 52.920

7075 T6511 4.545 54.540

7075 T73511 4.549 54.588

3-1/2" 2024 T3511 5.258 63.096

6061 T6511 5.151 61.812

7075 T6511 5.410 64.920

4" 2024 T3511 6.007 72.084

6061 T6511 5.880 70.560

7075 T6511 6.059 72.708



EXTRUDEDALUMINUM


125

1.800.423.6651


(562) 802-2721


2-1/2"x 4" 7075 T6511 12.120 145.440

7075 T73511 12.130 145.560

4-1/2" 6061 T6511 13.250 159.000

5" 6061 T6511 14.700 176.450

6" 2024 T3511 18.020 216.240

6061 T6511 17.640 211.680

7075 T6511 18.200 218.400

7075 T73511 18.200 218.400

8" 2024 T3511 24.030 288.360

3" x 3-1/2" 6061 T6511 12.348 148.176

7075 T6511 12.730 152.760

4" 2024 T3511 14.420 173.040

6061 T6511 14.112 169.344

7075 T6511 14.540 174.480

7075 T73511 14.560 174.720

5" 2024 T3511 18.020 216.240

6061 T6511 17.640 211.680

7075 T73511 18.200 218.400

6" 2024 T3511 21.620 259.440

6061 T6511 21.168 254.016

7075 T6511 21.820 261.840

7075 T73511 21.840 262.080

8" 2024 T3511 28.830 345.960

6061 T6511 28.250 339.000

3-1/2"x4" 6061 T6511 16.480 197.760

7075 T6511 16.980 203.760

4" x 5" 2024 T3511 24.040 288.480

7075 T6511 24.240 290.880

7075 T73511 24.280 291.360

6" 2024 T3511 28.830 345.960

6061 T6511 28.220 338.640

7075 T6511 29.090 349.080

7075 T73511 29.120 349.440

8" 6061 T6511 37.680 452.160

1-3/4"x 2" 6061 T6511 4.120 49.440

2-1/2" 6061 T6511 5.152 61.824

3" 6061 T6511 6.180 74.160

4" 6061 T6511 8.240 98.880

5" 6061 T6511 10.301 123.612

6" 6061 T6511 12.360 148.320

8" 6061 T6511 16.480 197.760

2" x 2-1/2" 2024 T3511 6.000 72.000

6061 T6511 5.810 69.720

7075 T6511 6.066 72.792

3" 2024 T3511 7.210 86.520

6061 T6511 7.056 84.672

7075 T6511 7.270 87.240

7075 T73511 7.279 87.348

3-1/2" 6061 T6511 8.240 98.880

4" 2024 T3511 9.610 115.320

6061 T6511 9.408 112.896

7075 T6511 9.696 116.352

7075 T73511 9.705 116.460

5" 2024 T3511 12.020 144.240

6061 T6511 11.770 141.200

7075 T6511 12.120 145.440

6" 2024 T3511 14.420 173.040

6061 T6511 14.110 169.320

7075 T6511 14.540 174.480

7075 T73511 14.560 174.720

7" 6061 T6511 16.480 197.760

8" 6061 T6511 18.830 225.960

10" 6061 T6511 23.540 282.480

12" 6061 T6511 28.250 339.000

2-1/4"x 3" 6061 T6511 7.945 95.340

4" 6061 T6511 10.600 127.200

6" 6061 T6511 15.900 190.800

2-1/2"x 3" 2024 T3511 9.010 108.120

6061 T6511 8.820 105.840

7075 T6511 9.090 109.080

3-1/2" 6061 T6511 10.300 123.600

4" 2024 T3511 12.000 144.000

6061 T6511 11.760 141.120






126

(562) 802-2721


5" 2024 T351 3.003 36.036

5/8" x 3/4" 2024 T351 .5632 6.758

1" 2024 T351 .7507 9.008

2024 T851 .7501 9.001

7075 T651 .7582 9.098

1-1/2" 2024 T351 1.126 13.512

2024 T851 1.126 13.512

7075 T651 1.137 13.644

2" 2024 T351 1.501 18.012

2024 T851 1.502 18.024

7075 T651 1.516 18.192

2-1/4" 2024 T351 1.689 20.268

2-1/2" 2024 T351 1.877 22.524

7075 T651 1.895 22.747

3" 2024 T351 2.252 27.024

7075 T651 2.274 27.295

4" 2024 T351 3.003 36.036

7075 T651 3.032 36.394

3/4" x 1" 2024 T351 .9009 10.811

2024 T851 .9010 10.812

7075 T651 .9089 10.907

7075 T7351 .9098 10.918

1-1/4" 2024 T351 1.126 13.512

7075 T651 1.137 13.649

1-1/2" 2024 T351 1.351 16.212

2024 T851 1.351 16.212

7075 T651 1.363 16.356

7075 T7351 1.365 16.380

2" 2024 T351 1.801 21.612

2024 T851 1.802 21.624

7075 T651 1.818 21.816

7075 T7351 1.820 21.840

2-1/2" 2024 T351 2.252 27.024

7075 T651 2.272 27.264

3" 2024 T351 2.702 32.424

1/8" x 5/8" 2024 T4 .0939 1.127

3/4" 2024 T4 .1127 1.352

1-1/4" 2024 T4 .1876 2.251

2" 2024 T4 .3000 3.600

2-1/2" 2024 T4 .3755 4.506

3" 2024 T4 .4500 5.400

3" 7075 T651 .9098 10.918

4" 2024 T4 1.201 14.412

4-1/2" 2024 T4 1.351 16.212

7075 T651 1.213 14.556

3/16"x 1" 7075 T651 .2276 2.731

1/4" x 2" 7075 T651 .6065 7.278

3/8" x 5/8" 2024 T4 .2815 3.378

3/4" 2024 T4 .3377 4.052

1" 2024 T4 .4504 5.405

7075 T651 .4545 5.454

1-1/2" 2024 T4 .6758 8.110

7075 T651 .6817 8.180

2" 2024 T4 .9009 10.811

7075 T651 .9089 10.907

2-1/4" 2024 T4 1.013 12.156

2-1/2" 2024 T4 1.126 13.512

3" 7075 T651 1.363 16.362

1/2" x 3/4" 2024 T351 .4504 5.405

1" 2024 T351 .6001 7.201

2024 T851 .6010 7.212

7075 T651 .6060 7.272

7075 T7351 .6066 7.279

1-1/4" 2024 T351 .7507 9.008

7075 T651 .7582 9.098

1-1/2" 2024 T351 .9009 10.811

2024 T851 .9010 10.812

7075 T651 .9089 10.907

2" 2024 T351 1.201 14.412

2024 T851 1.201 14.412

7075 T651 1.212 14.544

2-1/2" 7075 T651 1.515 18.180

3" 2024 T351 1.801 21.612

7075 T651 1.818 21.816

3-1/2" 2024 T351 2.102 25.224

4" 2024 T351 2.402 28.824

7075 T651 2.424 29.088

4-1/2" 2024 T351 2.702 32.424



1/2" x



127

1.800.423.6651


(562) 802-2721




7075 T651 6.059 72.708

2-1/2" 2024 T351 4.504 54.048

7075 T651 4.550 54.600

3" 2024 T351 5.405 64.860

2024 T851 5.410 64.920

7075 T651 5.450 65.400

3-1/2" 2024 T651 6.306 75.672

7075 T651 6.490 77.880

4" 2024 T351 7.207 86.484

2024 T851 7.210 86.520

7075 T651 7.270 87.240

5" 2024 T351 9.009 108.108

7075 T651 9.090 109.080

6" 2024 T351 10.81 129.720

2" x 2-1/2" 2024 T351 6.006 72.072

7075 T651 6.066 72.792

3" 2024 T351 7.207 86.484

7075 T651 7.270 87.240

3-1/2" 2024 T351 8.408 100.896

4" 2024 T351 9.609 115.308

7075 T651 9.696 116.352

4-1/2" 2024 T351 10.81 129.720

5" 2024 T351 12.01 144.120

7075 T651 12.12 145.440

6" 2024 T351 14.41 172.920

2-1/2"x 3" 7075 T651 9.090 109.080

4" 7075 T651 12.12 145.440

3" x 4" 2024 T351 14.41 172.920

7075 T651 14.54 174.480

6" 2024 T851 21.62 359.440

1-1/2"x 2" 2024 T351 3.603 43.236

2024 T851 3.610 43.320

7075 T651 3.636 43.632

2024 T851 6.000 72.1204"3" 7075 T651 2.727 32.724

4-1/2" 2024 T351 4.052 48.624

1" x 1-1/4" 2024 T351 1.510 18.120

1-1/2" 2024 T351 1.801 21.162

2024 T851 1.802 21.624

7075 T651 1.818 21.816

7075 T7351 1.820 21.840

2" 2024 T351 2.402 28.824

2024 T851 2.402 28.824

7075 T651 2.424 29.088

7075 T7351 2.426 29.112

2-1/2" 2024 T351 3.003 36.036

7075 T651 3.030 36.360

3" 2024 T351 3.603 43.236

2024 T851 3.603 43.236

7075 T651 3.636 43.632

3-1/2" 2024 T351 4.204 50.448

7075 T651 4.240 50.880

4" 2024 T351 4.804 57.648

2024 T851 4.805 57.660

7075 T651 4.848 58.176

4-1/2" 2024 T351 5.405 64.860

6" 7075 T651 7.272 87.264

5" 2024 T351 6.006 72.072

1-1/4" x 1-1/2" 7075 T651 2.274 27.288

2" 2024 T351 3.003 36.036

2024 T851 3.000 36.000

7075 T651 3.030 36.360

2-1/2" 2024 T351 3.756 45.072

7075 T651 3.787 45.444

3" 2024 T351 4.505 54.060

2024 T851 4.500 54.000

7075 T651 4.545 54.540

3-1/2" 2024 T351 5.260 63.120

7075 T651 5.410 64.920

4" 2024 T351 6.007 72.084

3-1/2" 2024 T351 3.153 37.836

4" 2024 T351 3.603 43.236

7075 T651 3.636 43.632

3/4" x 1-1/4"x

ALUMINUM128FRY STEEL COMPANY1.800.423.6651

[email protected]

(562) 802-2721

TOLERANCES PLUS OR MINUS

TOLERANCES - COLD FINISHEDALUMINUM ROUND - BAR AND RODSIZE

IN INCHES

0.065" - 0.374"0.375" - 0.500"0.501" - 1.000"1.001" - 1.500"1.501" - 2.000"2.001" - 3.000"3.001" - 3.499"3.500" - 4.999"5.000" - 6.000" Incl.6.001" - 7.000" Incl.7.001" - 8.000" Incl.

TOLERANCE PLUS OR MINUS*

.001"

.0015"

.002"

.0025"

.004"

.006"

.008"

.012"

.020"

.025"

.030"

TOLERANCES - COLD FINISHEDALUMINUM SQUARE AND HEXAGON BAR

SIZE IN INCHES

0.065" - 0.374"

0.375" - 0.500"

0.501" - 1.000"

1.001" - 1.500"

1.501" - 2.000"

2.001" - 3.000"

3.001" - 4.000"


.002"

.002"

.0025"

.003"

.005"

.008"

.013"

SIZE IN INCHES

Up thru 0.035"

0.036" - 0.064"

0.065" - 0.500"

0.501" - 0.750"

0.751" - 1.000"

1.001" - 1.500"

1.501" - 2.000"

2.001" - 3.000"

3.001" - 4.000"

4.001" - 6.000"

WIDTH*

. .

. .

.002"

.0025"

.0025"

.003"

.005"

.008"

.010"

.013"

THICKNESS*.001"

.0015"

.002"

.0025"

.0025"

.003"

.005"

.008"

.010"

.013"

*ALL TOLERANCES ARE IN INCHES

NOTE: ALL TOLERANCES SHOWN ARE FROM THE USA ALUMINUM STANDARDS AND DATA MANUAL.

TOLERANCES - COLD FINISHALUMINUM RECTANGLE BAR



(562) 802-2721

Up thru 0.124" 0.006"0.125" - 0.249" 0.007"0.250" - 0.499" 0.008"0.500" - 0.749" 0.009"0.750" - 0.999" 0.010"1.000" - 1.499" 0.012"1.500" - 1.999" 0.014"2.000" - 3.999" 0.024"4.000" - 5.999" 0.034"6.000" - 7.070" 0.044"7.071" - 7.999" 0.044"8.000" - 8.659" 0.054"8.660" - 8.999" 0.064"9.000" - 9.238" 0.064"9.239" - 9.999" 0.064"

10.000" -11.999" 0.074"12.000" -13.999" 0.084"14.000" -15.999" 0.094"

SIZE TOLERANCEIN INCHES PLUS OR MINUS*

HEXAGONS

TOLERANCES - EXTRUDED ALUMINUM - ROD AND BAR

*ALL TOLERANCES ARE IN INCHES

NOTE: ALL TOLERANCES SHOWN ARE FROM THE USA ALUMINUM STANDARDS AND DATA MANUAL.

Up thru 0.124" 0.006"0.125" - 0.249" 0.007"0.250" - 0.499" 0.008"0.500" - 0.749" 0.009"0.750" - 0.999" 0.010"1.000" - 1.499" 0.012"1.500" - 1.999" 0.014"2.000" - 3.999" 0.024"4.000" - 5.999" 0.034"6.000" - 7.070" 0.044"7.071" - 7.999" 0.054"8.000" - 8.659" 0.064"8.660" - 8.999" 0.064"9.000" - 9.238" 0.064"9.239" - 9.999" 0.064"

10.000" - 11.999" 0.074"12.000" - 13.999" 0.084"14.000" - 15.999" 0.094"


ROUNDS SQUARES

TOLERANCES - EXTRUDEDALUMINUM - RECTANGLE BAR

THICKNESS OR WIDTH (DISTANCE ACROSS FLATS)THICKNESS OR WIDTH

IN INCHES

Up thru 0.124"0.125" - 0.249"0.250" - 0.499"0.500" - 0.749"0.750" - 0.999"1.000" - 1.499"1.500" - 1.999"2.000" - 3.999"4.000" - 5.999"6.000" - 7.999"8.000" - 9.999"

10.000" - 11.999"12.000" - 13.999"14.000" - 15.999"16.000" - 17.999"18.000" - 19.999"20.000" - 21.999"22.000" - 24.000"


0.006"0.007"0.008"0.009"0.010"0.012"0.014"0.024"0.034"0.044"0.054"0.074"0.084"0.094"0.104"0.114"0.124"0.124"

Up thru 0.124" 0.006"0.125" - 0.249" 0.007"0.250" - 0.499" 0.008"0.500" - 0.749" 0.009"0.750" - 0.999" 0.010"1.000" - 1.499" 0.012"1.500" - 1.999" 0.014"2.000" - 3.999" 0.024"4.000" - 5.999" 0.034"6.000" - 7.070" 0.044"7.071" - 7.999" 0.044"8.000" - 8.659" 0.054"8.660" - 8.999" 0.054"9.000" - 9.238" 0.054"9.239" - 9.999" 0.054"

10.000" - 11.999" 0.074"12.000" - 13.999" 0.084"14.000" - 15.999" 0.094"16.000" - 17.999" 0.104"18.000" - 19.999" 0.114"20.000" - 21.999" 0.124"


CA

RB

ON

CA

RB

ON

CARBON STEEL

GRADES STOCKED


[email protected]

(562) 802-2721

C-1018 .15/.20 .60/.90 .04 .05

Ledloy (A) .13 .80/1.20 .04/.09 .20/.33 .15/.35

C-12L14 .15 .85/1.15 .04/.09 .26/.35 .15/.35

MACHINABILITY RATINGSCARBON

MAN- PHOS- CHROM- MOLYB-AISI CARBON GANESE PHORUS SULFER LEAD SILICON NICKEL IUM DENUM OTHERS

CHEMICAL ANALYSES — Maximum Unless Indicated

CARBON C.D. CARBON STEELRECOMMENDED MINIMUM STOCK REMOVAL FOR SURFACE IMPERFECTIONS

NON-SULFER / NON-LEAD FREE MACH: SUL OR LEAD - .001 PER 1/16" (.062) PER SIDE - .0015 PER 1/16" (.062) PER SIDE

NOTE: INSPECTION PRIOR TO ALTERING MATERIAL IS ADVISABLE.

NOTE: IT IS NOT ADVISABLE TO TRY TO “FINISH” ON SIZE FROM THE SIZE PURCHASED.

*CHEMICALS MEET QQS 633 A--QQS-634 (1010 THROUGH 1050)*CHEMICALS MEET QQS-637--(1109 THROUGH 1215)

*CHEMICALS MEET ASTM-A-108--(1010 THROUGH 1215)

C-1018*C-12L14*

LEDLOY (A)

SPECIFICATIONS

C-1018 130 78C-12L14 325 198 Ledloy (A) 325 198


GRADE


%RELATIVE SPEEDBASED ON

C-1212 as 100%

STOCK REMOVAL

STRAIGHTNESS: cold finished carbon steel bars are machine straightened within reasonable limits and are suitable forthe majority of industrial uses. The degree of straightness is satisfactory for operation in an automatic screw machine.



COLD DRAWNCARBON STEEL




(562) 802-2721

SIZE TYPE SIZE TYPE

13/32" Ledloy (12L14)

7/16" C1018Ledloy (12L14)

.4425"/.4445" Ledloy (12L14)

29/64" Ledloy (12L14)

15/32" Ledloy (12L14)

1/2" C1018Ledloy (12L14)

.505"/.507" Ledloy (12L14)

33/64" Ledloy (12L14)

17/32" Ledloy (12L14)

9/16" C1018Ledloy (12L14)

37/64" Ledloy (12L14)

19/32" Ledloy (12L14)

5/8" C1018Ledloy (12L14)

.630" Ledloy (12L14)

41/64" Ledloy (12L14)

21/32" Ledloy (12L14)

11/16" C1018Ledloy (12L14)

23/32" Ledloy (12L14)

3/4" C1018Ledloy (12L14)

.755"/.757" Ledloy (12L14)

25/32" Ledloy (12L14)

13/16" C1018Ledloy (12L14)

7/8" C1018Ledloy (12L14)

15/16" C1018Ledloy (12L14)

1" C1018 Ledloy (12L14)

1/16" Ledloy (12L14)

3/32" Ledloy (12L14)

7/64" Ledloy (12L14)

1/8" C1018Ledloy (12L14)

.130" Ledloy (12L14)

9/64" Ledloy (12L14)

5/32" C1018Ledloy (12L14)

11/64" Ledloy (12L14)

3/16" C1018Ledloy (12L14)

.190"/.192" Ledloy (12L14)

13/64" Ledloy (12L14)

7/32 C1018Ledloy (12L14)

15/64" Ledloy (12L14)

1/4" C1018Ledloy (12L14)

.255"/.257" Ledloy (12L14)

17/64" Ledloy (12L14)

9/32" C1018Ledloy (12L14)

19/64" Ledloy (12L14)

5/16" C1018Ledloy (12L14)

.318" Ledloy (12L14)

21/64" Ledloy (12L14)

11/32" C1018Ledloy (12L14)

23/64" Ledloy (12L14)

3/8" C1018Ledloy (12L14)

.380"/.382" Ledloy (12L14)

25/64" Ledloy (12L14)



COLD DRAWN CARBON STEEL



[email protected]

(562) 802-2721

SIZE TYPE SIZE TYPE

2-3/8" C1018Ledloy (12L14)

2-7/16" C1018

2-1/2" C1018Ledloy (12L14)

2-5/8" C1018Ledloy (12L14)

2-11/16" C1018

2-3/4" C1018Ledloy (12L14)

2-7/8" C1018Ledloy (12L14)

2-15/16" C1018

3" C1018Ledloy (12L14)

3-1/8" C1018Ledloy (12L14)

3-3/16" C1018

3-1/4" C1018Ledloy (12L14)

3-3/8" C1018

3-7/16" C1018

3-1/2" C1018Ledloy (12L14)

3-5/8" C1018Ledloy (12L14)

3-3/4" C1018Ledloy (12L14)

3-15/16" C1018

4" C1018Ledloy (12L14)

4-1/8" C1018

4-1/4" C1018Ledloy (12L14)

4-3/8" C1018

4-7/16" C1018

1-1/16" C1018Ledloy (12L14)

1-1/8" C1018Ledloy (12L14)

1-3/16" C1018Ledloy (12L14)

1-1/4" C1018Ledloy (12L14)

1-5/16" C1018 Ledloy (12L14)

1-3/8" C1018 Ledloy (12L14)

1-7/16" C1018 Ledloy (12L14)

1-1/2" C1018 Ledloy (12L14)

1-9/16" C1018Ledloy (12L14)

1-5/8" C1018Ledloy (12L14)

1-11/16" C1018

1-3/4" C1018Ledloy (12L14)

1-13/16" C1018Ledloy (12L14)

1-7/8" C1018Ledloy (12L14)

1-15/16" C1018

2" C1018Ledloy (12L14)

2-1/16" C1018

2-1/8" C1018Ledloy (12L14)

2-3/16" C1018Ledloy (12L14)

2-1/4" C1018Ledloy (12L14)

2-5/16" C1018Ledloy (12L14)

5/8" C1018Ledloy (12L14)

11/16" C1018Ledloy (12L14)

3/4" C1018Ledloy (12L14)

13/16" Ledloy (12L14)

7/8" C1018Ledloy (12L14)

15/16" Ledloy (12L14)

1" C1018Ledloy (12L14)

1-1/16" C1018Ledloy (12L14)

1-1/8" C1018 Ledloy (12L14)

1-3/16" Ledloy (12L14)

1/8" Ledloy (12L14)

5/32" Ledloy (12L14)

3/16" C1018Ledloy (12L14)

7/32" Ledloy (12L14)

1/4" C1018Ledloy (12L14)

5/16" C1018Ledloy (12L14)

3/8" C1018Ledloy (12L14)

7/16" C1018Ledloy (12L14)

1/2" C1018Ledloy (12L14)

9/16" C1018Ledloy (12L14)







(562) 802-2721

SIZE TYPE SIZE TYPE

7" C1018

7-1/2" C1018Ledloy (12L14)

7-1/2" C1018

8" C1018Ledloy (12L14)

8" C1018

8-1/2" C1018

9" C1018Ledloy (12L14)

9" C1018

9-1/2" C1018

10" C1018

11" C1018

4-1/2" C1018Ledloy (12L14)

4-3/4" C1018Ledloy (12L14)

5" C1018Ledloy (12L14)

5-1/4" C1018Ledloy (12L14)

5-1/2" C1018Ledloy (12L14)

5-3/4" C1018

6" C1018Ledloy (12L14)

6-1/4" C1018

6-3/4" C1018

7" C1018Ledloy (12L14)


SIZE TYPE SIZE TYPE






[email protected]

(562) 802-2721

SIZE TYPE SIZE TYPE

1-1/4" C1018 Ledloy (12L14)

1-3/8" C1018

1-1/2" C1018 Ledloy (12L14)

1-5/8" C1018

1-3/4" C1018Ledloy (12L14)

1-7/8" C1018

2" C1018Ledloy (12L14)

2-1/4" C1018

2-1/2" C1018

2-3/4" C1018

3" C1018

3-1/2" C1018

4" C1018

6" C1018

1/8" C1018

3/16" C1018

1/4" C1018Ledloy (12L14)

5/16" C1018

3/8" C1018Ledloy (12L14)

7/16" C1018

1/2" C1018Ledloy (12L14)

9/16" C1018

5/8" C1018Ledloy (12L14)

3/4" C1018Ledloy (12L14)

7/8" C1018Ledloy (12L14)

15/16" C1018

1" C1018Ledloy (12L14)

1-1/8" C1018


1-3/4" C1018

1-7/8" C1018

2" C1018

2-1/8" C1018

2-1/4" C1018

2-1/2" C1018

3" C1018

1-1/4" C1018 Ledloy (12L14)

1-3/8" C1018

1-3/8" Ledloy (12L14)

1-7/16" C1018

1-1/2" C1018 Ledloy (12L14)

1-5/8" C1018

SIZE TYPE SIZE TYPE




1018 FLATSSTOCKED IN 12' R/L



(562) 802-2721

Size Size Size Size Size

1" x 1-1/4"1-3/8"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/4"3-1/2"4"4-1/2"5"5-1/2"6"8"9"10"12"

1-1/8" x 1-1/4"1-1/2"1-3/4"2"2-1/2"3"4"

1-1/4" x 1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/2"4"4-1/2"5"6"8"10"12"

1-1/2" x 1-3/4"2"2-1/4"2-1/2"

1-1/2" x 2-3/4"3"3-1/2"4"4-1/2"5"6"8"

1-3/4" x 2"2-1/4"2-1/2"2-3/4"3"3-1/2"4"5"6"

2" x 2-1/4"2-1/2"2-3/4"3"3-1/2"4"4-1/2"5"5-1/2"6"8"

2-1/4" x 2-1/2"3"4"

2-1/2" x 3"3-1/2"4"4-1/2"

3" x 3-1/2"4"5"6"8"

4" x 5"

1/2" x 12"

5/8" x 1"1-1/4"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/2"4"4-1/2"5"6"

3/4" x 1"1-1/8"1-1/4"1-3/8"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/4"3-1/2"4"4-1/2"5"5-1/2"6"8"

7/8" x 1"1-1/4"1-1/2"1-3/4"2"2-1/2"3"3-1/2"4"5"6"

1/8" x 1/4"5/16"3/8"1/2"5/8"3/4"1-3/4"2-1/4"3"

3/16" x 3/8"5/8"7/8"1-1/8"1-3/4"2-1/4"2-3/4"3"3-1/2"5"6"

1/4" x 3/8"1"1-1/8"1-1/4"1-3/8"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/4"3-1/2"4"4-1/2"7"

5/16" x 3/8"3/4"1"1-1/4"1-1/2"1-3/4"2"2-1/4"2-1/2"

5/16" x 3"3-1/2"4"

3/8" x 7/8"1"1-1/8"1-1/4"1-3/8"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/4"3-1/2"4"4-1/2"5"6"

7/16" x 1"1-1/4"1-1/2"2"2-1/2"

1/2" x 1"1-1/8"1-1/4"1-3/8"1-1/2"1-3/4"2"2-1/4"2-1/2"2-3/4"3"3-1/4"3-1/2"4"4-1/2"5"5-1/2"6"6-1/2"8"

CARBON STEEL WEIGHTS

ROUNDS


[email protected]

(562) 802-2721



1/16" .001 .010 .123/32" .002 .023 .287/64" .003 .032 .381/8" .004 .042 .50.130" .004 .0451 .549/64" .004 .053 .645/32" .005 .065 .7811/64" .007 .079 .953/16" .008 .094 1.13.192" .008 .0989 1.18613/64" .009 .110 1.32

7/32" .011 .128 1.5415/64" .012 .147 1.761/4" .014 .167 2.00.255" .014 .1736 2.08317/64" .016 .188 2.2569/32" .018 .211 2.5319/64" .019 .235 2.825/16" .022 .261 3.13.318" .022 .269 3.22821/64" .024 .287 3.4411/32" .026 .316 3.7923/64" .029 .345 4.143/8" .031 .376 4.51.380" .032 .3855 4.6225/64" .034 .407 4.8813/32" .037 .441 5.297/16" .043 .511 6.13.442" .044 .5225 6.2729/64" .046 .548 6.57615/32" .049 .587 7.041/2" .056 .668 8.02.505" .057 .680 8.1633/64" .059 .710 8.5217/32" .063 .754 9.059/16" .070 .845 10.1437/64" .074 .892 10.7019/32" .078 .941 11.295/8" .087 1.043 12.52.630" .088 1.06 12.7241/64" .092 1.096 13.1521/32" .096 1.150 13.8011/16" .105 1.262 15.1423/32" .115 1.379 16.553/4" .125 1.502 18.02.756" .127 1.522 18.2649/64" .131 1.565 18.7825/32" .136 1.630 19.5613/16" .147 1.763 21.167/8" .170 2.044 24.5315/16" .192 2.347 28.16

1" .22 2.670 32.041/64" .23 2.750 33.001/16" .25 3.014 36.171/8" .28 3.379 40.553/16" .31 3.766 45.191/4" .35 4.173 50.085/16" .38 4.600 55.203/8" .42 5.049 60.597/16" .46 5.518 66.22

1"1/2" .50 6.008 72.109/16" .54 6.520 78.245/8" .59 7.051 84.6111/16" .64 7.604 91.253/4" .68 8.178 98.1413/16" .73 8.773 105.307/8" .78 9.388 112.7015/16" .84 10.02 120.20

2" .89 10.68 128.21/16" .95 11.36 136.31/8" 1.01 12.06 144.73/16" 1.07 12.78 153.41/4" 1.13 13.52 162.25/16" 1.19 14.28 171.43/8" 1.26 15.06 180.77/16" 1.33 15.87 190.41/2" 1.39 16.69 200.35/8" 1.54 18.40 220.811/16" 1.61 19.29 231.53/4" 1.69 20.20 242.47/8" 1.84 22.07 264.815/16" 1.92 23.04 276.5

3" 2.01 24.03 288.41/8" 2.18 26.08 312.93/16" 2.27 27.13 325.61/4" 2.36 28.21 338.53/8" 2.54 30.42 365.07/16" 2.64 31.55 378.61/2" 2.73 32.71 392.55/8" 2.93 35.09 421.13/4" 3.14 37.55 450.615/16" 3.45 41.40 496.8

4" 3.56 42.73 512.61/8" 3.79 45.43 545.21/4" 4.02 48.23 578.73/8" 4.26 51.11 613.37/16" 4.39 52.58 630.91/2" 4.51 54.07 648.93/4" 5.03 60.25 723.0

5" 5.56 66.75 801.11/4" 6.13 73.60 883.21/2" 6.73 80.77 969.23/4" 7.36 88.29 1059.0

6" 8.01 96.12 1153.51/4" 8.71 104.3 1252.01/2" 9.40 112.8 1353.83/4" 10.14 121.7 1460.0

7" 10.90 130.8 1570.81/2" 12.52 150.2 1802.2

8" 14.24 170.9 2050.61/2" 16.08 192.9 2315.0

9" 18.02 216.3 2595.21/2" 20.08 241.0 2891.6

10" 22.25 267.0 3204.0


HEXAGONS


SQUARES



(562) 802-2721



1/8" .004 .046 .555/32" .006 .072 .8643/16" .009 .104 1.257/32" .012 .140 1.6815/64" .013 .1618 1.942 1/4" .015 .184 2.215/16" .02 .288 3.463/8" .03 .414 4.977/16" .05 .564 6.771/2" .06 .736 8.839/16" .08 .932 11.185/8" .10 1.150 13.8011/16" .12 1.392 16.703/4" .14 1.656 19.8713/16" .16 1.944 23.337/8" .19 2.254 27.0515/16" .22 2.588 31.06

1" .25 2.945 35.341/16" .28 3.324 39.891/8" .31 3.727 44.723/16" .35 4.152 49.821/4" .38 4.601 55.213/8" .46 5.567 66.807/16" .51 6.085 73.021/2" .55 6.625 79.505/8" .65 7.775 93.303/4" .75 9.019 108.231-7/8" .86 10.35 124.2

2" .98 11.78 141.41/8" 1.11 13.30 159.61/4" 1.24 14.91 178.91/2" 1.53 18.40 220.8

3" 2.21 26.50 318.0



1/8" .004 .053 .6363/16" .010 .120 1.4361/4" .017 .213 2.555/16" .03 .332 3.9813/8" .04 .478 5.7367/16" .05 .651 7.8101/2" .07 .850 10.2009/16" .09 1.076 12.9105/8" .11 1.328 15.9403/4" .16 1.913 22.9607/8" .22 2.603 31.24015/16" .25 2.988 35.856

1" .28 3.400 40.801/8" .36 4.303 51.641/4" .44 5.313 63.763/8" .54 6.428 77.141/2" .64 7.650 91.80

1"5/8" .75 8.980 107.743/4" .87 10.410 124.957/8" 1.00 11.950 143.44

2" 1.13 13.600 163.201/4" 1.43 17.21 206.61/2" 1.77 21.25 255.03/4" 2.14 25.72 308.6

3" 2.55 30.6 367.21/2" 3.47 41.65 500.0

4" 4.53 54.4 652.81/2" 5.74 68.85 826.2

5" 7.08 85.0 1020.0


FLATS


[email protected]

(562) 802-2721


1/8" x 3/16" .007 .072 .8641/4" .009 .106 1.275/16" .011 .133 1.603/8" .013 .159 1.917/16" .016 .186 2.231/2" .018 .213 2.565/8" .022 .266 3.193/4" .027 .319 3.837/8" .031 .372 4.461" .035 .425 5.101-1/8" .040 .480 5.761-1/4" .044 .531 6.371-3/8" .049 .588 7.061-1/2" .053 .638 7.661-5/8" .058 .696 8.351-3/4" .062 .744 8.932" .071 .850 10.202-1/4" .080 .956 11.472-1/2" .089 1.063 12.762-3/4" .097 1.160 13.903" .106 1.275 15.303-1/4" .115 1.380 16.563-1/2" .124 1.488 17.864" .142 1.700 20.404-1/2" .159 1.913 22.965" .177 2.125 25.506" .213 2.550 30.60

3/16" x 1/4" .013 .160 1.925/16" .017 .199 2.393/8" .020 .239 2.877/16" .023 .279 3.351/2" .027 .319 3.835/8" .033 .398 4.783/4" .040 .478 5.747/8" .047 .558 6.701" .053 .638 7.661-1/8" .060 .717 8.601-1/4" .066 .797 9.561-3/8" .073 .877 10.521-1/2" .080 .956 11.471-3/4" .093 1.116 13.392" .106 1.275 15.302-1/4" .120 1.440 17.282-1/2" .133 1.594 19.132-3/4" .146 1.750 21.003" .159 1.913 22.963-1/2" .186 2.231 26.774" .213 2.550 30.604-1/2" .239 2.870 34.405" .266 3.188 38.266" .319 3.825 45.908" .425 5.100 61.2010" .532 6.380 76.5612" .638 7.660 91.92

1/4" x 5/16" .022 .266 3.193/8" .027 .319 3.837/16" .031 .372 4.461/2" .035 .425 5.109/16" .040 .480 5.765/8" .040 .531 6.37

1/4" x 3/4" .053 .628 7.667/8" .062 .744 8.931" .071 .850 10.201-1/8" .080 .956 11.471-1/4" .089 1.063 12.761-3/8" .097 1.160 13.901-1/2" .106 1.275 15.301-5/8" .115 1.380 16.561-3/4" .124 1.488 17.862" .142 1.700 20.402-1/4" .159 1.913 22.962-1/2" .177 2.125 25.502-3/4" .195 2.340 28.083" .213 2.550 30.603-1/4" .230 2.760 33.123-1/2" .248 2.975 35.704" .283 3.400 40.804-1/2" .319 3.825 45.905" .354 4.250 51.005-1/2" .390 4.680 56.206" .425 5.100 61.207" .496 5.950 71.408" .567 6.800 81.6010" .708 8.500 102.0012" .850 10.200 122.4014" .992 11.900 142.80

5/16" x 3/8" .033 .398 4.787/16" .039 .460 5.521/2" .044 .531 6.375/8" .055 .664 7.973/4" .066 .797 9.567/8" .078 .930 11.161" .089 1.063 12.761-1/8" .099 1.200 14.401-1/4" .111 1.328 15.941-1/2" .133 1.594 19.131-3/4" .155 1.859 22.312" .177 2.125 25.502-1/4" .199 2.390 28.652-1/2" .221 2.656 31.862-3/4" .244 2.930 35.163" .266 3.188 38.263-1/2" .310 3.719 44.634" .354 4.250 51.004-1/2" .398 4.776 57.315" .443 5.313 63.766" .531 6.375 76.508" .708 8.500 102.0010" .885 10.630 127.5012" 1.06 12.750 153.00

3/8" x 7/16" .046 .576 6.911/2" .053 .638 7.669/16" .06 .720 8.645/8" .066 .797 9.563/4" .080 .956 11.477/8" .093 1.116 13.391" .106 1.275 15.301-1/8" .120 1.430 17.161-1/4" .133 1.594 19.131-3/8" .146 1.750 21.00



FLATS-Continued



(562) 802-2721



3/8" x 1-1/2" .159 1.913 22.961-5/8" .173 2.080 24.961-3/4" .186 2.231 26.772" .213 2.550 30.602-1/4" .239 2.869 34.432-1/2" .266 3.188 38.262-3/4" .292 3.500 42.003" .319 3.825 45.903-1/4" .345 4.140 49.683-1/2" .372 4.463 53.564" .425 5.100 61.204-1/2" .478 5.738 68.865" .531 6.375 76.505-1/2" .584 7.010 84.106" .637 7.650 91.807" .744 8.928 107.138" .850 10.200 122.409" .956 11.475 137.7010" 1.060 12.750 153.0012" 1.280 15.300 183.6014" 1.490 17.856 214.27

7/16" x 1/2" .062 .744 8.935/8" .078 .929 11.153/4" .093 1.116 13.397/8" .109 1.344 16.131" .124 1.488 17.861-1/4" .155 1.859 22.311-1/2" .186 2.231 26.771-3/4" .217 2.600 31.202" .248 2.975 35.702-1/2" .310 3.720 44.603" .372 4.460 53.504" .496 5.950 71.40

1/2" x 9/16" .080 .960 11.525/8" .089 1.063 12.763/4" .106 1.275 15.307/8" .124 1.488 17.861" .142 1.700 20.401-1/8" .159 1.920 23.001-1/4" .177 2.125 25.501-3/8" .195 2.340 28.001-1/2" .213 2.550 30.601-5/8" .230 2.760 33.121-3/4" .248 2.975 35.702" .283 3.400 40.802-1/4" .319 3.825 45.902-1/2" .354 4.250 51.002-3/4" .390 4.675 56.103" .425 5.100 61.203-1/4" .460 5.524 66.243-1/2" .496 5.950 71.404" .567 6.800 81.604-1/4" .602 7.225 86.704-1/2" .637 7.650 91.805" .708 8.500 102.005-1/2" .779 9.350 112.206" .850 10.200 122.406-1/2" .921 11.052 132.627" .992 11.904 142.848" 1.130 13.600 163.20

1/2" x 9" 1.280 15.360 184.3210" 1.420 17.000 204.0012" 1.700 20.400 244.80

9/16" x 5/8" .100 1.200 14.403/4" .120 1.440 17.281" .159 1.910 22.901-1/4" .199 2.390 28.701-1/2" .239 2.870 34.442" .319 3.830 45.96

5/8" x 3/4" .133 1.594 19.137/8" .155 1.859 22.311" .177 2.125 25.501-1/8" .199 2.390 28.601-1/4" .221 2.656 31.871-3/8" .244 2.930 35.161-1/2" .266 3.188 38.261-5/8" .288 3.454 41.451-3/4" .310 3.719 44.632" .354 4.250 51.002-1/4" .398 4.781 57.372-1/2" .438 5.313 63.762-3/4" .487 5.840 70.003" .531 6.375 76.503-1/4" .576 6.906 82.873-1/2" .620 7.438 89.264" .708 8.500 102.004-1/4" .752 9.031 108.284-1/2" .797 9.560 114.705" .885 10.630 127.605-1/2" .974 11.690 140.306" 1.060 12.750 153.007" 1.240 14.880 178.568" 1.420 17.000 204.009" 1.590 19.080 228.9610" 1.770 21.250 255.0012" 2.130 25.500 306.00

3/4" x 7/8" .186 2.230 26.771" .213 2.550 30.601-1/8" .239 2.880 34.561-1/4" .266 3.188 38.261-3/8" .292 3.500 42.001-1/2" .319 3.825 45.901-5/8" .345 4.140 49.681-3/4" .372 4.463 53.562" .425 5.100 61.202-1/4" .478 5.738 68.862-1/2" .531 6.375 76.602-3/4" .584 7.000 84.003" .637 7.650 91.803-1/4" .691 8.290 99.483-1/2" .744 8.925 107.004" .850 10.200 122.404-1/4" .903 10.840 130.054-1/2" .956 11.470 137.605" 1.060 12.750 153.005-1/2" 1.170 14.040 168.506" 1.280 15.300 186.306-1/2" 1.380 16.560 198.727" 1.490 17.880 214.56


FLATS-Continued


[email protected]

(562) 802-2721



3/4" x 8" 1.700 20.400 244.809" 1.910 22.920 275.0410" 2.130 25.500 306.0012" 2.550 30.600 367.2014" 2.980 35.760 429.12

7/8" x 1" .248 2.975 35.701-1/8" .279 3.350 40.201-1/4" .310 3.719 44.631-3/8" .341 4.090 49.001-1/2" .372 4.463 53.561-3/4" .434 5.206 62.472" .496 5.950 71.402-1/4" .558 6.696 80.352-1/2" .620 7.438 89.262-3/4" .682 8.180 98.163" .744 8.925 107.103-1/2" .868 10.410 124.904" .992 11.900 142.804-1/2" 1.120 13.440 161.285" 1.240 14.880 178.506" 1.490 17.850 214.207" 1.730 20.880 250.568" 1.980 23.800 285.6010" 2.480 29.750 357.0012" 2.980 35.700 428.4014" 3.480 41.650 500.00

1" x 1-1/8" .319 3.828 45.931-1/4" .354 4.250 51.001-3/8" .390 4.680 56.161-1/2" .425 5.100 61.201-5/8" .460 5.523 66.271-3/4" .496 5.950 71.402" .567 6.800 81.602-1/4" .637 7.650 92.332-1/2" .708 8.500 102.002-3/4" .779 9.350 112.203" .850 10.200 122.403-1/4" .921 11.050 132.603-1/2" .992 11.900 142.803-3/4" 1.060 12.750 153.004" 1.130 13.600 163.204-1/4" 1.200 14.450 173.404-1/2" 1.280 15.300 183.605" 1.420 17.000 204.005-1/2" 1.560 18.720 224.646" 1.700 20.400 244.806-1/2" 1.840 22.080 264.967" 1.980 23.800 285.608" 2.270 27.200 326.409" 2.550 30.600 367.2010" 2.830 34.000 408.0012" 3.400 40.800 489.6014" 3.970 47.600 571.20

1-1/8"x 1-1/4" .399 4.780 57.381-3/8" .438 5.260 63.121-1/2" .478 5.740 68.851-3/4" .558 6.694 80.332" .638 7.650 91.802-1/4" .717 8.606 103.28

1-1/8"x 2-1/2" .797 9.560 114.753" .956 11.470 137.664" 1.270 15.280 183.36

1-1/4"x 1-3/8" .487 5.840 70.131-1/2" .531 6.375 76.501-5/8" .576 6.900 82.801-3/4" .620 7.438 89.262" .708 8.500 102.002-1/4" .797 9.563 114.802-1/2" .885 10.630 127.602-3/4" .974 11.690 140.003 1.060 12.750 153.003-1/4" 1.150 13.800 165.603-1/2" 1.240 14.880 178.604" 1.420 17.000 204.004-1/4" 1.510 18.062 216.754-1/2" 1.590 19.126 229.515" 1.770 21.250 255.006" 2.130 25.500 306.007" 2.480 29.760 357.008" 2.830 34.000 408.0010" 3.540 42.500 510.0012" 4.250 51.000 612.0014" 4.960 59.500 714.00

1-3/8"x 1-1/2" .584 7.010 84.122" .779 9.348 112.183" 1.170 14.040 168.48

1-1/2"x 1-3/4" .744 8.920 107.102" .850 10.200 122.402-1/4" .956 11.480 137.802-1/2" 1.060 12.750 153.002-3/4" 1.170 14.040 168.483" 1.280 15.300 183.603-1/4" 1.380 17.500 198.903-1/2" 1.490 17.850 214.203-3/4" 1.590 19.130 229.514" 1.700 20.400 244.804-1/4" 1.810 21.680 260.124-1/2" 1.910 22.920 275.045" 2.13 25.50 306.005-1/2" 2.34 28.08 336.966" 2.55 30.60 367.207" 2.98 35.70 428.408" 3.40 40.80 489.6010" 4.25 51.00 612.0012" 5.10 61.20 734.40

1-3/4"x 2" .992 11.90 142.802-1/4" 1.12 13.44 161.282-1/2" 1.24 14.88 178.602-3/4" 1.36 16.32 195.803" 1.49 17.85 214.203-1/4" 1.61 19.34 232.063-1/2" 1.74 20.88 250.604" 1.98 23.80 285.604-1/2" 2.23 26.78 321.315" 2.48 29.76 357.205-1/2" 2.73 32.73 392.706" 2.98 35.70 428.408" 3.97 47.60 571.00


FLATS-Continued



(562) 802-2721



1-3/4"x 10" 4.96 59.52 714.2412" 5.95 71.40 856.80

2" x 2-1/4" 1.28 15.36 184.302-1/2" 1.42 17.00 204.002-3/4" 1.56 18.72 224.603" 1.70 20.40 244.803-1/4" 1.84 22.10 265.203-1/2" 1.98 23.80 285.603-3/4" 2.13 25.50 306.004" 2.27 27.20 326.004-1/4" 2.41 28.90 346.804-1/2" 2.55 30.60 367.005" 2.83 34.00 408.005-1/2" 3.12 37.44 449.286" 3.40 40.80 489.606-1/2" 3.68 44.20 530.407" 3.97 47.60 571.208" 4.53 54.40 652.809" 5.10 61.20 734.4010" 5.67 68.00 816.0012" 6.80 81.60 979.20

2-1/4"x 2-1/2" 1.59 19.13 229.503" 1.91 22.95 275.404" 2.55 30.60 367.204-1/2" 2.87 34.43 413.105" 3.19 38.25 459.006" 3.83 45.90 551.00

2-1/2"x 3" 2.13 25.50 306.003-1/4" 2.30 27.63 331.503-1/2" 2.48 29.75 357.003-3/4" 2.66 31.88 382.514" 2.83 34.00 408.004-1/2" 3.19 38.25 459.005" 3.54 42.50 510.005-1/2" 3.90 46.75 561.006" 4.25 51.00 612.008" 5.67 68.00 816.0012" 8.50 102.00 1224.00

3" x 3-1/2" 2.98 35.76 429.124" 3.40 40.80 489.604-1/2" 3.83 45.90 551.005" 4.25 51.00 612.005-1/2" 4.68 56.10 673.206" 5.10 61.20 734.407" 5.95 71.40 856.808" 6.80 81.60 979.20

3-1/2"x 4" 3.97 47.60 571.005" 4.96 59.50 714.006" 5.95 71.40 857.008" 7.93 95.20 1142.40

4" x 5" 5.67 68.04 816.486" 6.80 81.60 979.208" 9.07 108.84 1306.08

SIZE TOLERANCES*

CARBON STEEL


[email protected]

(562) 802-2721

To 1-1/2" incl. .................................. 0.002 0.003 0.004 0.005Over 1-1/2" to 2-1/2" incl. ........... 0.003 0.004 0.005 0.006Over 2-1/2" to 4" incl. ................. 0.004 0.005 0.006 0.007Over 4" to 6" incl. ................. 0.005 0.006 0.007 0.008Over 6" to 8"incl. .................. 0.006 0.007 0.008 0.009Over 8" to 9" incl. ................. 0.007 – – –Over 9" to 10" incl. ................ 0.008 – – –

NOTE: The tolerances for flats apply to thickness as well as width for cold finished flats.

STRAIGHTNESS: cold finished carbon steel bars are machine straightened within reasonable limits and are suitable forthe majority of industrial uses. The degree of straightness is satisfactory for operation in an automatic screw machine.

* ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES

To 3/4" incl. ..................................... 0.002 0.003 0.004 0.006Over 3/4" to 1-1/2" incl. ........... 0.003 0.004 0.005 0.007Over 1-1/2" to 2-1/2" incl. ........... 0.004 0.005 0.006 0.008Over 2-1/2" to 3-1/8" incl. ........... 0.005 0.006 0.007 0.009

HEXAGONS — COLD DRAWN

ROUNDS — COLD DRAWN OR TURNED AND POLISHEDMinus Minus Minus Minus

Maximum ofCarbon Range

Over 0.55%or Heat Treated


Over 0.28%to 0.55%

incl.


0.28%or less

Minus

FOR COLD FINISHED CARBON BARS AND SHAFTING

Size, Inches


0.28%or less


Over 0.28%to 0.55%

incl.


Over 0.55%or Heat Treated

(all Carbons)

Minus Minus

To 3/4" incl. ..................................... 0.002 0.004 0.005 0.007Over 3/4" to 1-1/2" incl. ........... 0.003 0.005 0.006 0.008Over 1-1/2" to 2-1/2" incl. ........... 0.004 0.006 0.007 0.009Over 2-1/2" to 4" incl. ................. 0.006 0.008 0.009 0.011Over 4" to 6’ incl. ................. 0.008 – – –

SQUARES — COLD DRAWN

To 3/4" incl. ..................................... .003 – – –Over 3/4" to 1-1/2" incl. ........... .004 – – –Over 1-1/2" to 3" incl. ................. .005 – – –Over 3" to 4" incl. ................. .006 – – –Over 4" to 6" incl. ................. .008 – – –Over 6"............................................. .013 – – –

FLATS — COLD FINISHEDWIDTH, IN INCHES* *The tolerances for flats apply to thickness as well as width.*

FATIGUE-PROOF

STRESSPROOF(C-1144)

FATIGUE-PROOF

STRESSPROOF(C-1144)

Size, Inches

Minus

BR

AS

S/B

RO

NZ

E

BR

AS

S/B

RO

NZ

E

BRASS/BRONZEGRADES STOCKED


[email protected]

(562) 802-2721

NI-AL-BRZ (ALLOY C-630)

AMS-4640, ASTM-B-150,ASME-B-150, QQC-465 AMD. 1,COND. HR-50 APPLYS TOSIZES UNDER 3"

SPECIFICATIONS

BRASS ALLOY 360,

FREE CUTTING,

1/2 HARD CHEMISTRY ONLY TO: ASTM-B-16

AND SAE CA - 360

SPECIFICATIONS

AUTOMATIC EXCEPTIONS TO THE SPECS LISTED ARE: LINE MARKING AND INSPECTION (I.E. MAG., SONIC, ETC.)

BRASSCHEMICAL ANALYSES — Maximum Unless Indicated

% RELATIVE SPEEDBASED ON

FM BRASS as 100%APPROXIMATE

SURF. FT.

C-360 1/2 HARD 100 –

Ni-Al-Brz – 40

MACHINABILITY RATINGS

BRASS / BRONZE


GRADE

C-360 60./63. 2.5/3.7 .35 Bal.

AISI COPPER LEAD IRON ZINC

BRONZECHEMICAL ANALYSES — Maximum Unless Indicated

TYPE Mn Si Ni + Co Al Fe Cu + Ag Zn Sn Pb

Ni-Al-Brz 1.5 .25 4./5.5 9./11. 2./4. Bal. .30 .20 .02

The above chart is a compilation of Aerospace, ASTM, Federal and Military specifications.It is for reference only and should not be used for design or specifications.

BRONZEROUNDSSTOCKED IN 12' R/L

Estimated Weight, Lbs.Size Grade Finish Per Foot 12 Ft Bar



(562) 802-2721

Finish: C.F. – Cold FinishR.T. – Rough Turned

1-5/8" NI-AL-BRZ (C-630) C.F. 6.740 80.880

1-11/16" NI-AL-BRZ (C-630) C.F. 7.280 87.360

1-3/4" NI-AL-BRZ (C-630) C.F. 7.830 93.960

1-13/16" NI-AL-BRZ (C-630) C.F. 8.390 100.680

1-7/8" NI-AL-BRZ (C-630) C.F. 8.980 107.760

2" NI-AL-BRZ (C-630) C.F. 10.220 122.640

2-1/16" NI-AL-BRZ (C-630) C.F. 10.985 131.820

2-1/8" NI-AL-BRZ (C-630) C.F. 11.540 138.480

2-3/16" NI-AL-BRZ (C-630) C.F. 12.357 148.284

2-1/4" NI-AL-BRZ (C-630) C.F. 12.940 155.280

2-5/16" NI-AL-BRZ (C-630) C.F. 13.810 165.720

2-3/8" NI-AL-BRZ (C-630) C.F. 14.410 172.920

2-7/16" NI-AL-BRZ (C-630) C.F. 15.343 184.116

2-1/2" NI-AL-BRZ (C-630) C.F. 15.970 191.640

2-9/16" NI-AL-BRZ (C-630) C.F. 16.957 203.484

2-5/8" NI-AL-BRZ (C-630) C.F. 17.600 211.200

2-3/4" NI-AL-BRZ (C-630) C.F. 19.320 231.840

2-7/8" NI-AL-BRZ (C-630) C.F. 21.110 253.320

3" NI-AL-BRZ (C-630) C.F. 22.990 275.880NI-AL-BRZ (C-630) R.T. 22.990 275.880

3-1/8" NI-AL-BRZ (C-630) R.T. 25.220 302.640

3-1/4" NI-AL-BRZ (C-630) R.T. 27.080 324.960

3-3/8" NI-AL-BRZ (C-630) R.T. 29.410 352.920

3-1/2" NI-AL-BRZ (C-630) R.T. 31.400 376.800

3-5/8" NI-AL-BRZ (C-630) R.T. 33.930 407.160

3/8" NI-AL-BRZ (C-630) C.F. .360 4.320

7/16" NI-AL-BRZ (C-630) C.F. .490 5.880

1/2" NI-AL-BRZ (C-630) C.F. .640 7.680

17/32" NI-AL-BRZ (C-630) C.F. .728 8.736

9/16" NI-AL-BRZ (C-630) C.F. .810 9.720

19/32" NI-AL-BRZ (C-630) C.F. .910 10.920

5/8" NI-AL-BRZ (C-630) C.F. 1.000 12.000

21/32" NI-AL-BRZ (C-630) C.F. 1.112 13.344

11/16" NI-AL-BRZ (C-630) C.F. 1.210 14.520

23/32" NI-AL-BRZ (C-630) C.F. 1.334 16.008

3/4" NI-AL-BRZ (C-630) C.F. 1.440 17.280

25/32" NI-AL-BRZ (C-630) C.F. 1.576 18.912

13/16" NI-AL-BRZ (C-630) C.F. 1.690 20.280

7/8" NI-AL-BRZ (C-630) C.F. 1.950 23.400

15/16" NI-AL-BRZ (C-630) C.F. 2.250 27.000

1" NI-AL-BRZ (C-630) C.F. 2.550 30.600

1-1/16" NI-AL-BRZ (C-630) C.F. 2.880 34.560

1-1/8" NI-AL-BRZ (C-630) C.F. 3.230 38.760

1-3/16" NI-AL-BRZ (C-630) C.F. 3.610 43.320

1-1/4" NI-AL-BRZ (C-630) C.F. 4.000 48.000

1-5/16" NI-AL-BRZ (C-630) C.F. 4.400 52.800

1-3/8" NI-AL-BRZ (C-630) C.F. 4.830 57.960

1-7/16" NI-AL-BRZ (C-630) C.F. 5.280 63.360

1-1/2" NI-AL-BRZ (C-630) C.F. 5.750 69.000

1-9/16" NI-AL-BRZ (C-630) C.F. 6.260 75.120




BRONZEROUNDSSTOCKED IN 12' R/L

5-1/4" NI-AL-BRZ (C-630) R.T. 71.180 854.160

5-1/2" NI-AL-BRZ (C-630) R.T. 80.840 970.080

6" NI-AL-BRZ (C-630) R.T. 92.290 1107.480

6-1/2" NI-AL-BRZ (C-630) R.T. 108.300 1299.600

7" NI-AL-BRZ (C-630) R.T. 125.600 1507.200

8" NI-AL-BRZ (C-630) R.T. 164.000 1968.000

3-3/4" NI-AL-BRZ (C-630) R.T. 36.050 432.600

3-7/8" NI-AL-BRZ (C-630) R.T. 38.780 465.360

4" NI-AL-BRZ (C-630) R.T. 41.020 492.240

4-1/4" NI-AL-BRZ (C-630) R.T. 46.200 554.400

4-3/8" NI-AL-BRZ (C-630) R.T. 49.430 593.160

4-1/2" NI-AL-BRZ (C-630) R.T. 51.900 622.800

4-5/8" NI-AL-BRZ (C-630) R.T. 55.240 662.880

4-3/4" NI-AL-BRZ (C-630) R.T. 58.270 699.240

5" NI-AL-BRZ (C-630) R.T. 64.100 769.200




[email protected]

(562) 802-2721

Estimated Weight, Lbs.Size Finish Per Foot 12 Ft Bar

BRASS 360“FM”ROUNDSSTOCKED IN 12' R/L




(562) 802-2721

23/64" C.F. 0.37 4.49

3/8" C.F. 0.41 4.88C.T. 0.41 4.88

.380" C.F. 0.42 5.01

25/64" C.F. 0.44 5.29

13/32" C.F. 0.48 5.74

27/64" C.F. 0.51 6.18

7/16" C.F. 0.55 6.65C.T. 0.55 6.65

.4425" C.F. 0.57 6.80

29/64" C.F. 0.59 7.13

15/32" C.F. 0.64 7.63

31/64" C.F. 0.68 8.15

1/2" C.F. 0.72 8.68C.T. 0.72 8.68

.505" C.F. 0.74 8.85

33/64" C.F. 0.77 9.23

17/32" C.F. 0.82 9.80

35/64" C.F. 0.87 10.38

9/16" C.F. 0.92 10.98

.5675" C.F. 0.93 11.19

37/64" C.F. 0.97 11.60

19/32" C.F. 1.02 12.24

39/64" C.F. 1.07 12.89

5/8" C.F. 1.13 13.56

.630" C.F. 1.15 13.78

41/64" C.F. 1.19 14.24

21/32" C.F. 1.25 15.00

11/16" C.F. 1.37 16.44

1/16" C.F. 0.01 0.16

5/64" C.F. 0.02 0.21C.T. 0.02 0.21

3/32" C.F. 0.03 0.30

.100" C.F. 0.03 0.35

7/64" C.F. 0.03 0.42

1/8" C.F. 0.05 0.54C.T. 0.05 0.54

.130" C.F. 0.05 0.59

9/64" C.F. 0.06 0.69

.144" C.F. 0.06 0.72

5/32" C.F. 0.07 0.85

11/64" C.F. 0.09 1.03

3/16" C.F. 0.10 1.22C.T. 0.10 1.22

.1925" C.F. 0.11 1.29

13/64" C.F. 0.12 1.43C.T. 0.12 1.43

7/32" C.F. 0.14 1.66

15/64" C.F. 0.16 1.91

1/4" C.F. 0.18 2.17C.T. 0.18 2.17

.255" C.F. 0.19 2.26

17/64" C.F. 0.20 2.45

9/32" C.F. 0.23 2.75

19/64" C.F. 0.26 3.06

5/16" C.F. 0.28 3.40C.T. 0.28 3.40

.3175" C.F. 0.29 3.50

21/64" C.F. 0.31 3.74

11/32" C.F. 0.34 4.10

Finish: C.F. – Cold FinishC.T. – Close Tolerance (± .0005)





BRASS 360“FM”ROUNDSSTOCKED IN 12' R/L


[email protected]

(562) 802-2721

2-1/4" C.F. 14.60 175.20

2-3/8" C.F. 16.30 195.60

2-1/2" C.F. 18.10 217.20

2-5/8" C.F. 19.90 238.80

2-3/4" C.F. 21.90 262.80

3" C.F. 26.00 312.00

3-1/8" C.F. 28.30 339.60

3-1/4" C.F. 30.60 367.20

3-1/2" C.F. 35.40 424.80

3-3/4" C.F. 40.70 488.40

4" C.F. 46.30 555.60

4-1/4" C.F. 51.77 621.24

4-1/2" C.F. 58.60 703.20

4-3/4" C.F. 64.60 775.20

5" C.F. 71.60 859.20

5-1/4" C.F. 79.00 948.00

5-1/2" C.F. 86.70 1040.40

6" C.F. 103.00 1236.00

6-1/2" C.F. 122.00 1464.00

7" C.F. 142.00 1704.00

8" C.F. 185.20 2222.40

23/32" C.F. 1.49 17.88

3/4" C.F. 1.63 19.56

.755" C.F. 1.65 19.79

25/32" C.F. 1.77 21.24

13/16" C.F. 1.91 22.92

27/32" C.F. 2.06 24.68

7/8" C.F. 2.22 26.64

.880" C.F. 2.24 26.89

15/16" C.F. 2.54 30.48

1" C.F. 2.89 34.68

1.005" C.F. 2.92 35.06

1-1/16" C.F. 3.27 39.24

1-1/8" C.F. 3.66 43.92

1-3/16" C.F. 4.08 48.96

1-1/4" C.F. 4.52 54.24

1-5/16" C.F. 4.98 59.76

1-3/8" C.F. 5.47 65.64

1-7/16" C.F. 5.98 71.76

1-1/2" C.F. 6.51 78.12

1-9/16" C.F. 7.06 84.72

1-5/8" C.F. 7.64 91.68

1-11/16" C.F. 8.24 98.88

1-3/4" C.F. 8.86 106.32

1-13/16" C.F. 9.51 114.12

1-7/8" C.F. 10.20 122.40

1-15/16" C.F. 10.90 130.80

2" C.F. 11.60 139.20

2-1/8" C.F. 13.06 156.72

13/16" C.F. 2.43 29.16

7/8" C.F. 2.82 33.84

1" C.F. 3.68 44.16

1-1/8" C.F. 4.62 55.44

1-1/4" C.F. 5.70 68.40

1-1/2" C.F. 8.21 98.52

1-3/4" C.F. 11.30 135.60

2" C.F. 14.70 176.40

2-1/2" C.F. 23.00 279.00

3" C.F. 33.12 397.44

1/8" C.F. 0.06 0.069

3/16" C.F. 0.13 1.56

1/4" C.F. 0.23 2.76

5/16" C.F. 0.36 4.32

3/8" C.F. 0.52 6.22

7/16" C.F. 0.70 8.46

1/2" C.F. 0.92 11.05

9/16" C.F. 1.17 14.04

5/8" C.F. 1.44 17.28

11/16" C.F. 1.74 20.88

3/4" C.F. 2.07 24.84


BRASS 360“FM”HEXAGONS

STOCKED IN 12' R/L




(562) 802-2721

1/8" C.F. 0.05 0.60

5/32" C.F. 0.08 0.93

3/16" C.F. 0.11 1.34

7/32" C.F. 0.15 1.84

1/4" C.F. 0.20 2.39

9/32" C.F. 0.25 3.02

5/16" C.F. 0.31 3.74

11/32" C.F. 0.38 4.52

3/8" C.F. 0.45 5.39

13/32" C.F. 0.53 6.32

7/16" C.F. 0.61 7.33

15/32" C.F. 0.70 8.41

1/2" C.F. 0.80 9.58

17/32" C.F. 0.90 10.81

9/16" C.F. 1.01 12.12

5/8" C.F. 1.25 15.00

11/16" C.F. 1.51 18.12

3/4" C.F. 1.80 21.60

Finish: C.F. – Cold FinishEXT. – Extruded

13/16" C.F. 2.11 25.32

7/8" C.F. 2.44 29.28

15/16" C.F. 2.72 32.66

1" C.F. 3.19 38.28

1-1/16" C.F. 3.60 43.20

1-1/8" C.F. 4.04 48.48

1-1/4" C.F. 4.99 59.88

1-5/16" C.F. 5.50 66.00

1-3/8" C.F. 6.03 72.36

1-7/16" C.F. 6.59 79.08

1-1/2" C.F. 7.18 86.16

1-5/8" C.F. 8.43 101.16

1-3/4" C.F. 9.77 117.24

2" C.F. 12.80 153.60

2-1/4" C.F. 15.68 188.61

2-1/2" C.F. 19.36 232.32

3" C.F. 28.69 344.28




3/4" x 1-1/2" C.F. 4.14 49.682" C.F. 5.53 66.312-1/2" C.F. 6.91 82.923" C.F. 8.29 99.473-1/2" C.F. 9.67 116.044" C.F. 11.05 132.60

7/8" x 1" C.F. 3.22 38.691-1/4" C.F. 4.03 48.361-1/2" C.F. 4.84 58.082" C.F. 6.45 77.402-1/2" C.F. 8.06 96.723" C.F. 9.67 116.044" C.F. 12.89 154.68

1" x 1-1/4" C.F. 4.59 55.081-1/2" C.F. 5.53 66.312" C.F. 7.37 88.422-1/4" C.F. 8.29 99.472-1/2" C.F. 9.21 110.523" C.F. 11.05 132.603-1/2" C.F. 12.89 154.734" C.F. 14.74 176.886" EXT. 22.06 264.72

1-1/4"x 1-3/4" C.F. 8.06 96.712" C.F. 9.21 110.523" C.F. 13.82 165.784" C.F. 18.42 221.04

1-1/2"x 2" C.F. 11.02 132.242-1/2" C.F. 13.82 165.783" C.F. 16.56 198.364" C.F. 22.03 264.366" EXT. 33.09 397.08

2" x 3" C.F. 22.10 265.204" C.F. 29.47 353.64

2-1/2"x 3" C.F. 27.63 331.56

3" x 5" EXT. 55.15 661.80

1/8" x 2" C.F. 0.92 11.05

1/4" x 1" C.F. 0.92 11.051-1/4" C.F. 1.15 13.781-1/2" C.F. 1.38 16.581-3/4" C.F. 1.61 19.282" C.F. 1.84 22.103" C.F. 2.76 33.164" C.F. 3.68 44.16

5/16" x 3/4" C.F. .863 10.361" C.F. 1.15 13.801-1/2" C.F. 1.72 20.66

3/8" x 3/4" C.F. 1.04 12.441" C.F. 1.38 16.581-1/4" C.F. 1.72 20.651-1/2" C.F. 2.07 24.792" C.F. 2.76 33.163" C.F. 4.15 49.744" C.F. 5.53 66.31

1/2" x 3/4" C.F. 1.38 16.521" C.F. 1.84 22.101-1/4" C.F. 2.30 27.541-1/2" C.F. 2.76 33.161-3/4" C.F. 3.21 38.562" C.F. 3.68 44.212-1/2" C.F. 4.59 55.083" C.F. 5.53 66.313-1/2" C.F. 6.45 77.364" C.F. 7.37 88.42

5/8" x 3/4" C.F. 1.73 20.701" C.F. 2.30 27.601-1/4" C.F. 2.88 34.561-1/2" C.F. 3.45 41.452" C.F. 4.59 55.082-1/2" C.F. 5.74 68.863" C.F. 6.89 82.624" C.F. 9.18 110.16

3/4" x 1" C.F. 2.76 33.16

BRASS 360“FM”FLATS

STOCKED IN 12' R/L






[email protected]

(562) 802-2721

BRASSTOLERANCES

[email protected]


(562) 802-2721

Over 1/2" to 1-1/4" incl. .004 .0045 .0045 – .005Over 1-1/4" to 2" incl. .0045 .005 .005 .006 .008Over 2" to 4" incl. .0045 .005 .006 .30% .012Over 4" – .007 .008 .30% .30%

Up to .150", incl. .0025Over .150" to .500", incl. .003Over .500" to 1.00", incl. .004Over 1.00" to 2.00", incl. .005Over 2.00" to 3.00", incl. .30% (A)

COLD FINISH, FREE CUTTING BRASS, ALLOY 360

ROUNDS - TOLERANCESPLUS OR MINUS * (IN.)

DIAMETER (IN.) COLD DRAWN ROUNDS

Up to .150", incl. .0013Over .150" to .500", incl. .0015Over .500" to 1.00", incl. .002Over 1.00" to 2.00", incl. .0025Over 2.00" to 8.00", incl. .15% (A)

HEXAGONS - TOLERANCESPLUS OR MINUS * (IN.)

DISTANCE BETWEEN PARALLEL SURFACES (IN.) COLD DRAWN HEXAGONS

1/8" .0023/16" .003Over 3/16" to 1/2", incl. .0035Over 1/2" to 1", incl. .0045Over 1" to 2", incl. .005Over 2" to 3", incl. .30% (A)

SQUARES - TOLERANCESPLUS OR MINUS * (IN.)

DISTANCE BETWEEN PARALLEL SURFACES (IN.) COLD DRAWN SQUARES

*ALL TOLERANCES ON THIS PAGE ARE A CLOSE APPROXIMATION BASED ON VARIOUS MILL MFG. PRACTICES.(A) PERCENT OF SPECIFIED THICKNESS EXPRESSED TO THE NEAREST .001

FLATSCF - COLD DRAWNPLUS OR MINUS * (IN.)

SPECIFIED WIDTH (IN.)THICKNESS TOLERANCE (IN.)

Up to1/2" incl.

Over 1/2"to 1" incl.

Over 1"to 2" incl.

Over 2"to 4" incl.

WIDTHTOLERANCE

(IN.)

GE

NE

RA

LIN

FO

RM

AT

ION

GENERAL INFORMATION

Additional Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153-156

Weight Formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156

Inches Conversions To Decimals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157

Hardness Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158

Formulas For Converting Rounds To Shapes . . . . . . . . . . . . . . . . . . . . . . . . . . . .159

Unified Numbering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

Color Code Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

Terms & Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163

About Fry Steel Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165

Definitions For The Steel Industry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

AEROSPACE MATERIAL SPECIFICATIONS(Continued)

AMS-5731 A-286 Solution Treated (1800° 1 Hour)AMS-5732 A-286 Solution Treated (1800°) and AgedAMS 5734 A-286 Solution Treated (1650° 2 hours)

(Chems Only)AMS-5735 Superseded by AMS-5732AMS-5736 Superseded by AMS-5731AMS-5737 A-286 Solution Treated (1650°) and AgedAMS-5738 303 Selenium High Yield (Condition B)AMS-5743 AM-355AMS-5744 AM-355 “Cap. of ”AMS-5750 Fry Alloy CAMS-5754 Fry Alloy XAMS-5759 L-605 (sic. Haynes 25)AMS-5764 1Nitronic 50 (XM-19) (22-13-5)AMS-5842 4MP-159AMS-5843 4MP-159 “Cap. of”AMS-5844 4MP-35NAMS-5845 4MP-35N “Cap. of”AMS-5848 1Nitronic 60AMS-5853 A-286 (Cap. 160 KSI) Cold Reduced

(Chems Only)AMS-5962 718 Cold ReducedAMS-6257 300M (Vacuum Melt.) (Exc. Hardness)AMS-6260 E-9310AMS-6265 E-9310 (Vacuum Melt.)AMS-6267 E-9310 (Vacuum Melt.)AMS-6322 E-8740AMS-6346 E-4130 HTAMS-6348 E-4130AMS-6349 E-4140 NormAMS-6370 E-4130AMS-6382 E-4140 AnnAMS-6409 E-4340 N & TAMS-6411 E-4330 Modified (Vacuum Melt.)AMS-6414 E-4340 (Vacuum Melt.)AMS-6415 E-4340AMS-6416 “300M” (obsolete-use AMS-6419)AMS-6417 E-4340 Modified (Vacuum Melt.)AMS-6418 Hy-Tuf Gr. A & BAMS-6419 300M (Vacuum Melt.)AMS-6427 E-4330 ModifiedAMS-6431 D6AC (Vacuum Melt.)AMS-6440 E-52100AMS-6444 E-52100 (Vacuum Melt.)AMS-6448 E-6150AMS-6470 E-135 Modified (Nitriding) (Exc. Hardness)AMS-6471 E-135 Modified (Nitriding) (Vacuum Melt.)AMS-6472 E-135 Modified (Nitriding Comp A)AMS-6484 E-4340/E-4340 (Vacuum Melt.)AMS-6485 H-11AMS-6487 H-11 (Vacuum Melt.)AMS-6488 H-11 (Vacuum Melt.)AMS-6514 Maraging (Grade 300)AMS-6526 9-4-30 Exc. ConditionAMS-6532 Aermet 100AMS-7718 4750 (Exc. Hardness)AMS-7727 3Kovar

MILITARY SPECS(Commonly Requested for Military Hardware)

MIL-I-23011 CL 1 3(Kovar)MIL-N (Nickel)MIL-N-6710 “600” Nickel Alloy “Exc. Max Tens”MIL-N-14411 Comp 3 (4750) “Cap. of”MIL-S (Steel)MIL-S-5000 E-4340

AEROSPACE MATERIALSPECIFICATIONS(Commonly Requested by Airframe & Missile Mfgrs.)AMS-2300 Magnetic Inspection Procedure Premium

Aircraft Quality (Vac. Melt.)AMS-2301 Aircraft Quality Magnetic Inspection

ProcedureAMS-2303 Aircraft Quality Magnetic Corrosion

Resistance Steel Inspection ProcedureAMS-2304 Special Aircraft-Quality Steel Cleanliness

Magnetic Particle Inspection ProcedureAMS-4117 Type 6061 T-651 C.F.AMS-4120 Type 2024 T-4 / T-351 C.F.AMS-4122 Type 7075 T-6 /T-73 (Chems Only) C.F.AMS-4123 Type 7075 T-651 C.F.AMS-4124 Type 7075 T-7351 (Chems Only) C.F.AMS-4154 Type 7075 T-6 EXT.AMS-4152 Type 2024 T-3 EXT.AMS-4150 Type 6061 T-6 EXT.AMS-4165 Type 2024 T-3511 EXT.AMS-4167 Type 7075 T-73511 EXT.AMS-4169 Type 7075 T-6511 EXT.AMS-4173 Type 6061 T-6511 EXT.AMS-4339 Type 2024 T-851 C.F.AMS-4640 NI-Al-BRZ ( C63000 )AMS-4674 “405” Nickel AlloyAMS-4675 “400” Nickel Alloy (Chems Only)AMS-4676 K-500 (Chems Only)AMS-5062 C-1018 (Chems Only)AMS-5069 C-1018 (Chems Only)AMS-5610 416 Condition A (Type 2)AMS-5612 410 Condition AAMS-5613 410 Condition AAMS-5616 418 (Greek Ascoloy) Condition AAMS-5617 3Custom 455 (12-9-2) Gr. 1 & 2AMS-5618 440 C Vac. Melt.AMS-5620 420-F Condition A (Type 2)AMS-5621 420 Condition AAMS-5627 430 Condition AAMS-5628 431 Condition AAMS-5629 PH 13-8 MO Solution TreatedAMS-5630 440-C Condition AAMS-5631 440-A Condition AAMS-5632 440-F Se (Type 2)AMS-5637 302 High Tensile (Condition B) (Chems Only)AMS-5639 304 Condition AAMS-5640 303 Condition A Type 1 & 2AMS-5641 303 Selenium Condition AAMS-5643 17-4 PH “Double” H-1150 (Chems Only)AMS-5643 17-4 PH “H-1150” (Chems Only)AMS-5643 17-4 PH Solution TreatedAMS-5644 17-7 PH Solution TreatedAMS-5645 321 Condition AAMS-5646 347 Condition AAMS-5647 304 L Condition AAMS-5648 316 Condition AAMS-5650 309 Condition AAMS-5651 310 Condition AAMS-5653 316 L Condition AAMS-5655 422 “Cap. of”AMS-5656 1Nitronic 40 (21-6-9)AMS-5659 15-5 PH “H-1025” (Type 1)AMS-5659 15-5 PH Solution Treated Type 1 & 2AMS-5662 718 Nickel AlloyAMS-5663 718 Nickel Alloy “Cap. of”AMS-5665 “600” Nickel Alloy (Chems Only)AMS-5666 “625” Nickel AlloyAMS-5667 X-750 Nickel AlloyAMS-5708 2Waspaloy H.Q.AMS-5709 2Waspaloy “Cap. of”AMS-5716 330 Condition AAMS-5726 A-286 (Cap. 210 KSI) Cold Reduced

1 Trademark Armco2 Trademark Carpenter Technology

3 Trademark United Technology4 Trademark SPS Technology

GE

NE

RA

LIN

FO

RM

AT

ION



(562) 802-2721

Specifications 154FRY STEEL COMPANY1.800.423.6651

[email protected]

(562) 802-2721

MIL-S-5626 E-4140MIL-S-6049 E-8740 MIL-S-6709 E-135 Modified Comp. A (Nitriding)MIL-S-6758 E-4130MIL-S-7108 E-Hy Tuf MIL-S-7393 E-9310 MIL-S-7420 E-52100MIL-S-7493 E-4620MIL-S-7720 303, 302, 316 (See top of page 154)MIL-S-83030 Comp. 3 E-9310 (Vacuum Melt.)MIL-S-8503 E-6150MIL-S-8699 E-4330MIL-S-8844 Class 1 E-4340 (Vacuum Melt.) MIL-S-8844 Class 3 E-4340 Modified “300M” (Vacuum Melt.)MIL-S-8949 D6AC (Exc. Sonic)MIL-S-16598 INVAR 36 “FM” (Chemistry Only)MIL-S-18732 431MIL-S-46850 Maraging Grade 300 Type 4 Exc. Para 3.5.3MIL-S-83135 E-4340 Modified (Vacuum Melt.)MIL-S-83311 Nickel 455MIL-W (Steel Wire)MIL-W-52263 (Same as ASTM-A-581)

FEDERAL SPECS(U.S. Government Method of Cataloging Metals)

QQN-281 Class A Nickel “400” AlloyClass B Nickel “405” Alloy

QQN-286 Form 1 Nickel “K500” Alloy “Annealed”Form 2 Nickel “K500” Alloy “Aged”

QQS-624 (Same as ASTM-A-322-A-331)QQS-633 (Same as QQS-634 & QQS-637)QQS-634 (1010 Thru 1050)QQS-637 (1109 Thru 1215)QQS-763 See top of page 154QQS-764 Superceded by ASTM-A-582

BOILER CODE SPECIFICATIONS(Commonly Requested by Bolt, Pump,

Fitting and Valve Mfgr’s)

ASTM-A- (American Society for Testing and Materials)ASTM-A-108 Carbon Steel Bars Cold Finished

C-1018 Thru C-1215 (Chems Only)ASTM-A-193 Alloy-Steel and Stainless Steel Bolting Materials

for High Temperature Service GR-B8 (304)GR-B8 CL 2 (304 Strain Hardened High Tensile)GR-B8C (347) GR-B8M (316) GR-B8M CL 2(316 Strain Hardened High Tensile) GR-B8T (321)GR-B8R(1Nitronic 50), GR-B8S(1Nitronic 60)

ASTM-A-194 Nitronic 60ASTM-A-276 Stainless and Heat Resisting Steel Bars and

Shapes302 309 316-L 403304 310 317 410304 “B” 316 321 420304 L 316 “B” 347 430(“B”= High Tensile) 431

1Nitronic 60 440-A1Nitronic 50 (XM-19, 22-13-5) 440-C1Nitronic 40 (21-6-9) 446

ASTM-A-320 Alloy Steel Bolting Materials for LowTemperature Service GR-B8(304) GRB8C(347)GR-B8T(321) GR-B8M(316)

ASTM-A-320 GR-B8F(303-303 Se)GR-B8F CL 2 (303 S “B”)

ASTM-A-322 Hot Rolled Alloy Steel BarsASTM-A-331 Cold Finished Alloy Steel Bars

(Same as A-322)ASTM-A-453 Bolting Materials, High Temperature,

(A286 Grade 660 CL A & B)ASTM-A-484 General Requirements for Stainless

(Except Wire)ASTM-A-479 Stainless and Heat Resisting Steel Bars and

Shapes for use in Boilers and otherPressure Vessels302 304-L 316 317 403304 310-S 316-L 321 430

1Nitronic 50 (XM-19, 22-13-5) 347410

1Nitronic 60 (UNS 21800)ASTM-A-564 Hot Rolled and Cold Finished Aged

Hardening Stainless and Heat Resisting Steel Bars and Shapes (Cap. of)Type 630-17-4 PH Type XM-12-15-5 PHType 631-17-7 PH Type XM-13-PH 13-8 Type 634-AM-355

ASTM-A-565 422 (Grade 616)ASTM-A-582 Free Machining Stainless and

Heat Resisting Steel Bars Hot Rolled or Cold Finished303 S (Cond. A), 416 (Cond. A & T)303 SE (Cond. A), 420-F, 430-F, 440-FSe

ASTM-A-638 Precipitation Hardening Iron BaseSuper Alloy Bars, Forgings andForging Stock for High Temperature Service GR-660 (A-286)Age Hard-Type 1 & 2

ASTM-B-16 Alloy 360 (Chems Only)ASTM-B-160 “200” Nickel AlloyASTM-B-164 “400” Nickel AlloyASTM-B-166 “600” Nickel Alloy (Chems Only)ASTM-B-446 “625” Nickel Alloy (Grade 1)ASTM-B-473 Fry Alloy 20ASTM-B-574 Fry Alloy CASTM-B-637 718 Nickel AlloyASTM-F-15 3Kovar

A.S.M.E. (American Society of Mechanical Engineers)ASME-SA-182 Same as ASTM-A-182ASME-SA-240 Same as ASTM-A-240ASME-SA-479 Same as ASTM-A-479 ASME-SB-574 Fry Alloy C (C-276)ASME-SB-637 718 Sol. Tr.

“COMPANY” SPECS:AIRESEARCH:EMS-537 416 H.T. (125 KSI Min.)EMS-642 H-11 V.M. (Exc. Fatigue Test)EMS-55443 AM-355 (Ariz. Div.)EMS-56280 9310 V.M.EMS-96242 E-4330 Mod. V.M. (Tor. Div.) (Exc. Sonic)HT-5042 9310 Air Melt. / V.M. (Cap. of)

MILITARY SPECIFICATIONS(Continued)

BOILER CODE SPECIFICATIONS(Continued)





(562) 802-2721

“COMPANY” SPECS(Continued)

ROCKWELL:ABO 170-014 4750 (Autonetics)LBO-160-164 18-9-5 Maraging (300 Grade) (L.A. Div.)MBO-160-003 17-4 PH (Cap. of)(Downey Div.)MBO-160-006 18-9-5 Maraging (Downey Div.) (300 Grade), (Exc. Sonic)MBO-160-034 304-L Vac. Melt (Downey Div.) (Exc. Sonic)MBO-160-037 304-L Vac. Melt (Downey Div.) (Exc. Grain Size)MBO-160-151 Invar 36 “FM”,(Chems Only)RBO-170-153 718 Sol TR, (AMS-5662)(Rocketdyne) (Cap. of)STO-160LB0013 PH 13-8 MO(Corporate)STO-160-LB0012 9-4-30 Vac Melt(Corporate)

STANDARD PRESSED STEEL:SPS-M-118 A-286 Cold Reduced (Cap. of 160 KSI)SPS-M-175 2Waspaloy Cold Reduced, (Exc.

Hardness)SPS-M-250 A-286 (Cap. 200 KSI) Cold ReducedSPS-M-275 718 Sol TR (AMS-5662) (Chems Only)SPS-M-637 718 Cold ReducedSPS-M-646 4MP 35N

VOI SHAN:VS-71001 2Waspaloy Cold Reduced, (Exc.

Hardness)

DEPT OF DEFENSE:DOD-F-24669/7 Stainless 422

WESTINGHOUSE:10705BU Stainless 422 (Cap of)

HI-SHEAR:HS#115 Stainless 431 (Chems Only)HS#140 Type 3 A-286 (AMS-5731), (Chems Only)HS#156 718 Sol Tr/Cold Reduced,

(Chems Only)

VALLEY TODECO:VMS-110 718 Cold Reduced, (Chems Only)VMS-112 2Waspaloy Cold Reduced, (Exc.

Hardness)

AIR INDUSTRIES:AIC-MS-110 718 Cold Reduced (Chems Only)

EUROPEAN STANDARD:EN-2404 718 Vac. Melt. Under 4"EN-2303 A286 (AMS 5737) Under 4"

“COMPANY” SPECS(Continued)

BELL:BPS 299-947-032 E-9310 V.M. (Exc. Hardness)BPS-299-947-036 E-135 Modified (Nitriding) V.M.BPS 299-947-055 E-4340 V.M.

BENDIX:CE-0896 E-4340 Mod V.M. “300”CE-0906 E-4330 Mod V.M.BEMS-25003 440-C Vac. Melt. (L.A. DIV.)

BOEING:BMS-7-26 E-4340 Mod Vac. Melt. N & T

“300M” Class 1BMS-7-27 E-4330 Mod N & T Hi TransverseBMS-7-28 E-4340 V.M., E-4340 N & TBMS-7-122 E-4330 Mod V.M.BMS-7-182 HP 9-4-30 (Type II)

GENERAL DYNAMICS:FMS-1011 D6-AC V.M. (Exc. Sonic)FMS-1012 4330 V.M. (Exc. Sonic)

GENERAL ELECTRICB50A951A1 Stainless 422 (Cap of)B50TF15 718 Sol Tr (AMS 5662)

718 Cold Reduced, (Chems Only)B50T69A 718 Sol Tr (AMS-5662)B50YP44B1 X-750C50TF13 718 Cold Reduced

(Chems Only)718 Sol Tr (AMS-5662)(Chems Only)

GRUMMAN AIRCRAFT:GM-1010 E-4330 Mod V.M. (Exc. Sonic)GM-1012 E-4340 Mod V.M. “300M”GM-1013 E-D6AC V.M. (Exc. Sonic)

HUGHES AIRCRAFT:HMS-6-1404 Type 2 Class 1 (V.M.)

Maraging 300HMS-6-1105 PH 13-8 MOHMS-6-1093 Type 455 (Exc. Para 3.2.1.1)

KAYNAR:MS-301 A-286 (AMS-5731),1-1/4” Rd Max

LOCKHEEDLC05-1190 (CA. CO) (4340 Mod) “300M” V.M.LCM05-2190 D6AC (V.M.) (Exc. Para 4.8.1)STM05-500 (Georgia) D6AC (V.M.)STM05-602 (Georgia) PH 13-8 MO

MC DONNELL DOUGLAS:DMS-1555 Grade A E-4340 Vac. Melt.

Grade B E-4340 N & TDMS-1565 431 Stainless Steel, (Exc. Sonic)DMS-1841 Grade A Hy-Tuf Vac. Melt.

Grade B Hy-TufDMS-1935 300 M V.M. (4340 Mod)DMS-2050 304-L Cond ADMS-2100 PH 13-8 MODMS-2209 718 Cold Reduced,

(Chems Only)MMS-2102 (St. Louis) HP-9-4-30, (Exc. Fracture & Sonic

Test)1 Trademark Armco2 Trademark Carpenter Technology


Specifications156FRY STEEL COMPANY1.800.423.6651

[email protected]

(562) 802-2721

QQ-S-763BSupersedes QQ-S-00763A Rev. 1

and MIL-S-854 (in part)

Class Type Class Type(1) 302 (8) CB 347(7) 303 (3) 410

303 Se (6) 416(1) 304 (5) 420

304L (4) 430310 430F

(9) 316 431316L (10) 440C

(8) Ti 321

MIL-S-7720 Amend. #1 Supersedes AN-S-771Conditions

COMPOSITION

302303 S303 Se316

PHYSICALCONDITION

(A) Annealed(B) Cold Finished(C) As Rolled

SURFACE CONDITION

(a) Hot Finished(b) Pickled(c) Cold Drawn(d) Cold Rolled(e) Turned(f) Centerless Ground

T = Thickness, Inches

HEXAGONS Steel:2.9473 x D 2

Aluminum:1.02 x D 2

D = Size, Inches

SQUARES Steel:3.4032 x D 2

Aluminum:1.18 x D 2

D = Size, Inches

WEIGHT FORMULASCONVERSION FACTORS

Multiply DensitySteel Weight by Lbs./In.3

LBS. PER LINEAL FOOT

ROUNDS Steel:2.6729 x D 2

Aluminum:.924 x D 2

D = Size, Inches

D

D

D

FLATS Steel:3.4032 x T x W

Aluminum:1.20 x T x W

W = Width, Inches

W

T

Aluminum2011 .3604 .1022024 .3533 .1006061 .3462 .098

7075 .3568 .101Stainless

300 Series 1.030 .292400 Series 1.010 .286

Nickel200 1.132 .321400 1.125 .318R-405 1.121 .318K-500 1.075 .305600 1.072 .306625 1.075 .305800H 1.012 .287800HT 1.012 .287825 1.037 .294330 1.012 .28720 1.030 .292C-276 1.132 .321

Brass 1.084 .307

6262 .3452 .098

FRACTIONAL INCHES CONVERTED TO DECIMAL INCHES



(562) 802-2721

Fraction of Inch Decimal of Inch

1/64. . . . .015625

1/32. . . . . . . .03125

3/64. . . . .046875

1/16 . . . . . . . .0625

5/64. . . . .078125

3/32. . . . . . . .09375

7/64. . . . .109375

1/8 . . . . . . . . . . . . .125

9/64. . . . .140625

5/32. . . . . . . .15625

11/64. . . .171875

3/16 . . . . . . . . . . . .1875

13/64. . . .203125

7/32. . . . . . . .21875

15/64. . . .234375

1/4 . . . . . . . . . . . . .250

17/64. . . .265625

9/32. . . . . . . .28125

19/64. . . .296875

5/16 . . . . . . . . . . . .3125

21/64. . . .328125

11/32. . . . . . .34375

23/64. . . .359375

3/8 . . . . . . . . . . . . .375

25/64. . . .390625

13/32. . . . . . .40625

27/64. . . .421875

7/16 . . . . . . . . . . . .4375

29/64. . . .453125

15/32. . . . . . .46875

31/64. . . .484375

1/2 . . . . . . . . . . . . .500

Fraction of Inch Decimal of Inch

33/64. . . .515625

17/32. . . . . . .53125

35/64. . . .546875

9/16 . . . . . . . . . . . .5625

37/64. . . .578125

19/32. . . . . . .59375

39/64. . . .609375

5/8 . . . . . . . . . . . . .625

41/64. . . .640625

21/32. . . . . . .65625

43/64. . . .671875

11/16 . . . . . . . . . . .6875

45/64. . . .703125

23/32. . . . . . .71875

47/64. . . .734375

3/4 . . . . . . . . . . . . .750

49/64. . . .765625

25/32. . . . . . .78125

51/64. . . .796875

13/16. . . . . . . . . . . .8125

53/64. . . .828125

27/32. . . . . . .84375

55/64. . . .859375

7/8 . . . . . . . . . . . . .875

57/64. . . .890625

29/32. . . . . . .90625

59/64. . . .921875

15/16. . . . . . . . . . . .9375

61/ 64 . . .953125

31/32. . . . . . .96875

63/64. . . .984375

1. . . . . . . . . . . . . . 1.000

HARDNESS CONVERSION TABLE

(Approximate)


[email protected]

(562) 802-2721

653 — 62 324,000

627 — 60 311,000

601 — 59 306,000

578 — 57 290,000

555 — 56 284,000

534 — 54 270,000

514 — 53 263,000

495 — 51 250,000

477 — 50 243,000

461 — 49 236,000

444 — 47 223,000

429 — 47 217,000

415 — 45 211,000

401 — 42 194,000

388 — 41 188,000

375 — 40 182,000

363 — 38 171,000

352 — 37 166,000

331 — 36 162,000

321 — 34 153,000

311 — 33 148,000

302 — 32 144,000

293 — 31 140,000

285 — 30 136,000

277 — 29 132,000

269 — 28 129,000

262 — 27 126,000

255 — 25 120,000

248 — 24 117,000

241 100 23 115,000

235 99 22 112,000

229 98 21 110,000

223 97 20 108,000

217 96 103,000

212 96 103,000

207 95 101,000

202 94 98,000

197 93 96,000

192 92 93,000

187 91 91,000

183 90 89,000

179 89 87,000

174 88 85,000

170 87 83,000

166 86 81,000

163 85 80,000

159 84 78,000

156 83 77,000

153 82 76,000

149 81 75,000

146 80 74,000

143 79 73,000

140 78 71,000

137 77 70,000

134 76 69,000

131 74 67,000

128 73 66,000

126 72 65,000

124 71 63,000

121 70 62,000

118 69 61,000

116 68 60,000

114 67 59,000

112 66 58,000

109 65 57,000

107 64 55,000

ApproximateBrinell Rockwell Rockwell Tensile

Hardness B Scale C Scale Lbs., p.s.i.

ApproximateBrinell Rockwell Tensile

Hardness B Scale Lbs., p.s.i.



(562) 802-2721

W2 + T2

d D E F

1/16 0.0721 0.0884 0.03611/8 0.1443 0.1767 0.07215/32 0.1804 0.2210 0.09023/16 0.2164 0.2651 0.10827/32 0.2526 0.3094 0.12631/4 0.2886 0.3535 0.14439/32 0.3247 0.3977 0.16235/16 0.3608 0.4419 0.180311/32 0.3968 0.4861 0.19833/8 0.4329 0.5303 0.216413/32 0.4690 0.5745 0.23447/16 0.5051 0.6187 0.252415/32 0.5412 0.6629 0.27051/2 0.5773 0.7071 0.288517/32 0.6133 0.7513 0.30659/16 0.6494 0.7955 0.324619/32 0.6855 0.8397 0.34265/8 0.7216 0.8839 0.360621/32 0.7576 0.9281 0.378711/16 0.7937 0.9723 0.396723/32 0.8298 1.0165 0.41473/4 0.8659 1.0606 0.432825/32 0.9020 1.1048 0.450813/16 0.9380 1.1490 0.468827/32 0.9741 1.1932 0.48697/8 1.0102 1.2374 0.504929/32 1.0463 1.2816 0.522915/16 1.0824 1.3258 0.541031/32 1.1184 1.3700 0.5590

1 1.1547 1.4142 0.57701-1/32 1.1907 1.4584 0.59501-1/16 1.2268 1.5026 0.61311-3/32 1.2629 1.5468 0.63111-1/8 1.2990 1.5910 0.64911-5/32 1.3351 1.6452 0.66721-3/16 1.3712 1.6793 0.68521-7/32 1.4073 1.7235 0.70321-1/4 1.4434 1.7677 0.72131-9/32 1.4794 1.8119 0.73931-5/16 1.5155 1.8561 0.75731-11/32 1.5516 1.9003 0.77541-3/8 1.5877 1.9445 0.79341-13/32 1.6238 1.9887 0.81141-7/16 1.6598 2.0329 0.82951-15/32 1.6959 2.0771 0.84751-1/2 1.7320 2.1213 0.86551-17/32 1.7681 2.1655 0.88361-9/16 1.8042 2.2097 0.90161-19/32 1.8403 2.2539 0.91961-5/8 1.8764 2.2981 0.93771-21/32 1.9124 2.3423 0.95571-11/16 1.9485 2.3865 0.97421-23/32 1.9846 2.4306 0.99181-3/4 2.0207 2.4708 1.0098

d D E F

1-25/32 2.0568 2.5190 1.02781-13/16 2.0929 2.5632 1.04591-27/32 2.1289 2.6074 1.06391-7/8 2.1650 2.6516 1.08191-29/32 2.2011 2.6958 1.10001-15/16 2.2372 2.7400 1.11801-31/32 2.2733 2.7842 1.13602 2.3094 2.8284 1.15402-1/32 2.3453 2.8726 1.17202-1/16 2.3815 2.9168 1.19012-3/32 2.4176 2.9610 1.20812-1/8 2.4537 3.0052 1.22612-5/32 2.4898 3.0404 1.24422-3/16 2.5259 3.0936 1.26222-1/4 2.5981 3.1820 1.29832-5/16 2.670 3.2703 1.33432-3/8 2.7424 3.3587 1.37042-7/16 2.8145 3.4471 1.40652-1/2 2.8867 3.5355 1.44252-9/16 2.9583 3.6239 1.47862-5/8 3.0311 3.7123 1.51472-11/16 3.1032 3.8007 1.55072-3/4 3.1754 3.8891 1.58682-13/16 3.2476 3.9794 1.62292-7/8 3.3197 4.0658 1.65892-15/16 3.3919 4.1542 1.69503 3.4641 4.2426 1.73103-1/16 3.5362 4.3310 1.76713-1/8 3.6084 4.4194 1.80323-3/16 3.6806 4.5078 1.83923-1/4 3.7627 4.5962 1.87533-5/16 3.8249 4.6846 1.91143-3/8 3.8971 4.7729 1.94743-7/16 3.9692 4.8613 1.98353-1/2 4.0414 4.9497 2.01963-9/16 4.1136 5.0381 2.05563-5/8 4.1857 5.1265 2.09173-11/16 4.2579 5.2149 2.12773-3/4 4.3301 5.3033 2.16383-13/16 4.4023 5.3917 2.19993-7/8 4.4744 5.4801 2.23593-15/16 4.5466 5.5684 2.27204 4.6188 5.6568 2.30804-1/8 4.7631 5.8336 2.38014-1/4 4.9074 6.0104 2.45234-3/8 5.0518 6.1872 2.52444-1/2 5.1961 6.3639 2.59654-3/4 5.485 6.717 2.74005 5.774 7.071 2.89005-1/4 6.062 7.425 3.03005-1/2 6.351 7.778 3.18005-3/4 6.640 8.132 3.32006 6.928 8.485 3.4600

DISTANCES ACROSS CORNERSOF HEXAGONS AND SQUARES

RECTANGLE INSCRIBEDIN A CIRCLE (DIAGONAL)

NOTE — These are theoretical distances for sharp corners only.

W = WIDTH T = THICKNESS(Square Root of Sum of Squares)

D = 1.1547dE = 1.4142dF = 0.5773d

UNIFIED NUMBERING SYSTEM INDEX


[email protected]

(562) 802-2721

UNS A92011 2011

UNS A92024 2024

UNS A96061 6061

UNS A96262 6262

UNS A97075 7075

UNS C36000 Alloy 360

UNS C62400 AL-BRZ

UNS C63000 NI-AL-BRZ

UNS G10180 1018

UNS G41300 4130

UNS G41400 4140

UNS G43400 4340

UNS G46200 4620

UNS G52986 52100

UNS G61500 6150

UNS G87400 8740

UNS G93106 9310

UNS K23080 4330 Mod.

UNS K24065 Nitriding

UNS K24728 D6AC

UNS K32550 Hy-Tuf

UNS K91283 9-4-30

UNS K92580 Aermet 100

UNS K93120 Maraging “300”

UNS K93602 Invar 36 “FM”

UNS K94610 3Kovar

UNS K95000 4750

UNS N02200 Nickel “200”



UNS N05500 Nickel “K-500”

UNS N06002 Fry Alloy “X”



UNS N07001 2Waspaloy

UNS N07718 718

UNS N07750 X-750

UNS N08020 Fry Alloy 20

UNS N08330 330


UNS N08810 Nickel “800-H”

UNS N08811 Nickel “800-HT”


UNS N10276 Fry Alloy C

UNS R30159 4MP 159

UNS R30035 4MP 35N

UNS R30605 L-605

UNS S13800 13-8 PH

UNS S15500 15-5 PH

UNS S17400 17-4 PH

UNS S17700 17-7 PH

UNS S45500 3Custom 455

UNS S20910 1Nitronic 50



UNS S30200 302

UNS S30300 303 Su

UNS S30323 303 Sel

UNS S30400 304

UNS S30403 304-L

UNS S30908 309-S

UNS S31008 310-S

UNS S31600 316

UNS S31603 316-L

UNS S31700 317

UNS S31703 317-L

UNS S32100 321

UNS S32109 321 H

UNS S34700 347

UNS S34709 347 H

UNS S35500 AM-355

UNS S40300 403

UNS S41000 410

UNS S41600 416

UNS S41800 418 (Greek Ascoloy)UNS S42000 420

UNS S42020 420-F

UNS S42200 422

UNS S43000 430

UNS S43020 430-F

UNS S43100 431

UNS S44002 440-A

UNS S44004 440-C

UNS S44023 440-F Sel

UNS S44600 446

UNS S66286 A-286

UNS T20811 H-11



SUPER ALLOYS

COLOR [email protected] 1.800.423.6651


(562) 802-2721

PH-13-8 MO Vac. Melt. Silver & Dk. Blue15-5 PH Vac. Melt. Dk. Blue & Copper15-5 E.S.R. Light Blue & Copper15-5 PH “H1025” Orange & Copper17-4 PH Silver & Red17-4 PH “H1150” Light Green & Gold17-4 PH “Double” H-1150 Black & Gold17-4 PH Prec. Grd. Silver & Copper17-7 PH Gold & Red3Custom 455 Lt. Blue & Green302 Pink & White302 “Cold Drawn Flats” Light Blue & Red302 Cond. “B” Red & Brown302 Prec. Grd. Gold & Pink303 Sul Red303 Sul “Cold Drawn Flats” Light Blue & White303 Sul Cond. “B.” Red & Yellow303 Sul Prec. Grd. Gold303 Sel Purple303 Sel Cond. “B.” Brown303 Sel Prec. Grd. Tan304 Pink & White304 “Cold Drawn Flats” Light Blue & Red304/304-L Cond. “B” Red & Brown304/304-L Prec. Grd. Gold & Pink304 L Pink & Brown304 L “Cold Drawn Flats” Light Blue & Red302/304/304-L Plate-Bar Pink & Green304 L Vac. Melt. Red & Pink309 Black & White310 Purple & Black316 Pink & Black316/316-L Cond. “B” Gray & Yellow316 L Pink & Dark Blue316/316-L Prec. Grd. Pink & Silver316/316-L Vac. Melt. Pink & Orange317/317 L Dk. Blue & Dk. Green321 Black330 Tan & Brown347 WhiteAM-355 Purple & White403/410 Green & Black416 Green416 “Cold Drawn Flats” Black & Tan416 Prec. Grd. Yellow416 HT RC 26/32 Green & Red418 (Greek Ascoloy) Red & Purple420 Gray & Black420 F Light Green422 Gray & Pink430 Blue & White430 F Red & Black431 Green & Yellow440 A Dk. Blue & Tan440 C Dark Blue440 C Prec. Grd. Light Blue440 C Vac. Melt. Dk. Blue & Aqua440 F Se Light Blue & Purple446 Light Green & Orange1Nitronic 40 Brown & Orange1Nitronic 50 Purple & Brown1Nitronic 60 Gray & BrownFry Alloy 20 Yellow & Orange



STAINLESS

A-286 Age Hard. AMS 5737 Green & WhiteA-286 Age Hard. AMS 5732 Purple & GoldA-286 Sol Treated AMS 5731 Yellow & BlackA-286 (Cap. 160 KSI) Light Blue & GoldCold ReducedA-286 (Cap. 210 KSI)Cold Reduced Black & Light BlueL-605 Orange & WhiteNickel “200” Silver & YellowNickel “400” Red & OrangeNickel “405” Light Blue & YellowNickel “K-500” ANN Gray & OrangeNickel “K-500” ANN & AGED Green & TanNickel “600” Green & PinkNickel “625” Purple & Silver718 Vac. Melt. AMS 5662 Orange & Blue718 Vac. Melt. (Cap. 220 KSI)Cold Reduced Yellow & PinkX-750 Brown & WhiteNickel “800/800-H/800-HT” Gold & SilverNickel “825” Dk. Blue & Lt. BlueMaraging “300” Brown & Green2Waspaloy Purple & Yellow4MP 35N Silver4MP 159 Gold & OrangeFry Alloy X Red & WhiteFry Alloy C Purple & Pink3Aermet 100 Lt. Green & Silver

INVAR 36 “FM” Pink3Kovar Chartreuse4750 Orange

E-4130 Norm PinkE-4130 H.T. RedE-4140 GrayE-4330 Mod. Vac. Melt. Orange & PurpleE-4340 YellowE-4340 Vac. Melt. Yellow & WhiteE-4340 Mod. Vac. Melt.(“300M”) Yellow & Dk. BlueE-4620 Vac. Melt. Black & BrownE-6150 Vac. Melt. Green & PurpleE-8740 Red & YellowE-9310 N&T Red & WhiteE-9310 N&T Vac. Melt. Brown & YellowE-52100 Vac. Melt. Red & TanD6AC Vac. Melt. TanH-11 Vac. Melt. Red & BlueHy-Tuf Orange & WhiteHy-Tuf Vac. Melt. Tan & PurpleNitriding Blue & BrownNitriding Vac. Melt. Gray & White9-4-30 Vac. Melt. Gold & White

ELECTRICAL STEELS

AIRCRAFT ALLOYS

COLOR CODE 162FRY STEEL COMPANY1.800.423.6651

[email protected]

(562) 802-2721

ALUMINUM

CF 2011 T-3 BrownCF 2024 T-4 RedCF 2024 T-351 RedCF2024 T-351 Red With Black StripeCF 2024 T-851 PinkEXT 2024 T-3 Red With White StripeEXT 2024 T-3511 Red With White StripeCF 6061 T-6 Dk BlueCF 6061 T-651 Dk BlueEXT 6061 T-6 Dk Blue With White StripeEXT 6061 T-6511 Dk Blue With White StripeCF 6262 T-9 OrangeEXT 6262 T-6511 Orange With White StripeCF 7075 T-6 BlackCF 7075 T-651 BlackCF 7075 T-651 White With Black StripeCF 7075 T-73 Black With Yellow StripeCF 7075 T-7351 Black With Yellow StripeEXT 7075 T-6 Black With White StripeEXT 7075 T-6511 Black With White StripeEXT 7075 T-73511 Yellow With Black Stripe

COLD FINISHED CARBON

C-1018 BlackC-12L14 WhiteLedloy-A White

BRASS/BRONZE

C-Alloy 360 Red & CopperNi-Al-Brz Bronze & Green

TERMS AND CONDITIONS



(562) 802-2721

As a Stock list, this book contains descriptions, sizes, and weights of items of steel, brass,bronze and aluminum normally carried in stock for immediate delivery.

As a Reference book, the information herein has been compiled from authoritative sourcessuch as: metal producers, trade associations, technical societies, and is believed to reflectaccurately standard practices. It should be recognized, however, that practices and producingequipment vary among mills. Constant technological changes are also taking place. The result is that properties and characteristics of the material itself can vary.Such variations should be realized and evaluated accordingly.

Material specifications are constantly being revised by issued agencies. The issuance of revisions represent upgrading of the material . It is the basic policy of producers, as well as suppliers, to work to the latest revisions. Data herein should be used as a guide with the realization that changes may occur at any time.

Procedure for purchase orders and general conditions of sale.

Confirmation of ordersWhen orders are received by telephone, every effort is made to ship exactly as requested, thesame day the order is placed, providing material is in stock. However, when material isprocessed and/or shipped prior to the receipt of a written confirming order, we cannot assumeresponsibility for any deviation from instructions or specifications contained on such confirming order. In order to avoid duplication of shipment, the written purchase order shouldclearly indicate if it is merely “confirming” a previously given telephone order.

QuotationsFry Steel prides itself in quoting prices promptly, either by telephone, facsimile or mailed written requests. Prices are subject to change without notice and delivery promises are subjectto delays which are beyond our control. Quotations of availability are subject to prior sale.

Warranties and ClaimsIn general Fry Steel warrants that the materials shipped to a customer meet the specifications designated by the customer at the time of order. The materials ordered from FrySteel should be inspected upon arrival for conformance with the specifications ordered including grade, size, and quantity. If materials shipped to a customer do not conform to suchspecifications, we will replace the non-conforming material or refund the purchase price to theoriginal customer provided a claim is submitted within a reasonable time. Fry Steel will alsohonor claims for defective material, if submitted within a reasonable time after shipment, provided the material has not been improperly used or processed, and subject to our inspection.

Since steel, brass/bronze and aluminum are basic materials whose uses and applications arelimited almost solely by the inventiveness and ingenuity of the user, FRY STEEL DOES NOTWARRANT THE SUITABILITY OF ANY OF OUR PRODUCTS FOR ANY PARTICULAR APPLICATION OR PURPOSE, OR MAKE ANY OTHER WARRANTIES EXPRESSED ORIMPLIED.

TERMS AND CONDITIONS


[email protected]

(562) 802-2721

Return shipmentsReturn shipments must be authorized by Fry Steel in advance. Material which has been cut orotherwise processed by the buyer or to his order is not returnable.

DeliveriesAny delivery schedule indicated is based on our present estimate of the time required to shipafter receipt of your order. Any item which is indicated to be shipped from a producing mill, isbased upon current production schedules from the producing mill. In the event of any delay inour performance due in whole or in part to any cause beyond our reasonable control, we shallhave such additional time for our performance as may be reasonably necessary under the circumstances. Acceptance by you of any goods shall constitute a waiver by you of any claimfor damages on account of any delay in delivery of such goods.

Suspension of PerformanceIf in our judgment, reasonable doubt exists as to your financial responsibility, or if you are pastdue in payment of any amount owing to us, we reserve the right, without liability and withoutprejudice to any other remedies, to suspend performance, decline to ship, to stop any material in transit, until we receive payment of all amounts owing to us, or adequate assuranceof such payment whether or not due.

ShipmentsUnless otherwise expressly stated, shipment may be by carrier or other means selected by FrySteel.

Tolerances and variationsAll goods shall be subject to tolerances and variations consistent with usual trade practicesregarding dimensions, straightness, section, composition and mechanical properties and normal variations in surface and internal conditions and quality and shall also be subject todeviations from tolerances and variations consistent with practical testing and inspection methods.

The data contained in the Stock List has been compiled and developed from many sources.Although every effort has been made to cross-check this information, Fry Steel Company is notresponsible for its accuracy. This data is not to be used for design or specification purposes.ALL DATA SHOULD BE VERIFIED.



(562) 802-2721

ABOUT FRY STEEL COMPANYAn Equal Opportunity Employer

Fry Steel was founded in 1946.

Our Warehouse is 180,000 total square feet.

ISO 9001 : 2000

126 Employees

Our Sales Staff is available from 5 AM to 6 PM Pacific Time.

53 Saws33 Cranes32 Trucks28 Scales141 Different Grades of Material9,000 Different size Items(2) 1,200 AMP Emergency Generators

FRY STEEL COMPANY POLICIES

To become and remain the finest long bar product distributor in North America.

To insure that the materials our customers order will be of the desiredquality and delivered in an expeditious manner.

To procure material from producers we feel to be of the highest quality inthe industry.

To promote organizational effectiveness and provide an open participa-tive work environment with an opportunity for personal growth for allemployees.

To cross train employees wherever possible.

DEFINITIONS FOR THE STEEL INDUSTRY


[email protected]

(562) 802-2721

AGE HARDENING – The term as applied to soft, orlow carbon steels, relates to a wide variety of com-mercially important, slow gradual changes that takeplace in properties of steels after the final treatment.These changes, which bring about a condition ofincreased hardness elastic limit, and tensile strengthwith a consequent loss in ductility, occur during theperiod in which the steel is at normal temperatures

AGING – Spontaneous changes in the physicalproperties (for example, increase in tensile strengthand hardness) of some metals, which occurs onstanding at atmospheric temperatures after finalcold working or after a final heat treatment.Frequently synonymous with the term “Age-Hardening.”

AIR COOLING – Cooling of the heated metal, inter-mediate in rapidity between slow furnace coolingand quenching, in which the metal is permitted tostand in the open air.

AIR HARDENING STEEL – A steel containing suffi-cient carbon and other alloying elements to hardenfully during cooling in air or other gaseous mediumsfrom a temperature above its transformation range.The term should be restricted to steels that arecapable of being hardened by cooling in air in fairlylarge sections, about 2 in. or more in diameter.

AISI STEELS – Steels of the American Iron and SteelInstitute. Common and alloy steels have been num-bered in a system essentially the same as the SAE.The AISI system is more elaborate than the SAE inthat all numbers are proceeded by letters: “A” repre-sents basic open-hearth alloy steel, “B” acidBessemer carbon steel, “C” basic open-hearth car-bon steels, “CB” either acid Bessemer or basicopen-hearth carbon steel, “E” electric furnace alloysteel.

ALLOY STEEL – A carbon steel to which is added adefinite amount of one or more elements other thancarbon, in order to impart special properties to thesteel so that it can be used for specific purposes.

ANGULARITY – The conformity to, or deviationfrom, specified angular dimensions in the cross sec-tion of a shape.

ANNEALING – Heat the material to a specific tem-perature then control the rate at which the materialcools (while in the furnace). This gives a uniformhardness and the best machining properties to thematerial. The purpose of such a heat treatment maybe: to remove stresses; to induce softness; to alterductility; toughness; electrical magnetic, or otherphysical properties; to refine the crystalline struc-ture; to remove gases; to produce a definite micro-

structure. In annealing, the temperature of the oper-ation and the rate of cooling depend upon the mate-rial being treated and the purpose of the treatment.

A.S.T.M. – Abbreviation for American Society forTesting Material. An organization for issuing stan-dard specifications on materials, including metalsand alloys.

AS ROLLED – The condition the material is in whenin comes off the sizing rollers. Cooling as it’s beingprocessed. As rolled is more prone to hard spotsand higher as shipped hardness.

ATOMIC SYMBOLS – Aluminum = Al Nitrogen = NBoron = B Oxygen = OCarbon = C Phosphorus = PChromium = Cr Selenium = SeCobalt = Co Silicon = SiColumbium = Cb Sulfer = SCopper = Cu Tantalum = TaHydrogen = H Tin = SnIron = Fe Titanium = TiLead = Pb Tungsten = WManganese = Mn Vanadium = VMolybdenum = Mo Yttreium = YtNickel = Ni

AUSTENITE – Phase in certain steels, characterizedas a solid solution, usually of carbon or iron carbide,in the gamma form of iron. Such steels are known as“austenitic.” Austenite is stable only above 1333 F. Ina plain carbon steel, but the presence of certainalloying elements, such as nickel and manganese,stabilizes the austenitic form, even at normal tem-perature.

AUSTENITIC STEEL – Steel which, because of thepresence of alloying elements, such as nickel, man-ganese, chromium, etc., shows stability of Austeniteat normal temperatures. (Example 200 & 300 series).Austenitic types are non-magnetic as annealed, anddepending on the composition, may become slight-ly magnetic when cold worked. They are readilywelded and may be work hardened to high levels,although, not as high as can be obtained by heattreating the hardenable types of the 400 series. Theaustenitic types provide the best corrosion resist-ance of all the stainless steels.

BILLET – An ingot or bloom that has been reducedthrough rolling or hammering to an approximatesquare ranging from 1-1/2 to 6 inches square, or toan approximate rectangular cross section of anequivalent area. Billets are classified as semifinishedproducts for rerolling or forging.

BLISTER – A raised spot on the surface of the metalcaused by expansion of gas in a subsurface zoneduring thermal treatment.

BLOWHOLE – A cavity produced during the solidifi-cation of metal by evolved gas, which, in failing toescape, in held in pockets.

BRASSES – Copper base alloys in which zinc is theprincipal added element. Brass is higher andstronger than either of its alloying elements copperor zinc; it is malleable and ductile; develops hightensile strength with cold-working and is not heattreatable for purposes of hardness development.

BRINELL HARDNESS – A common standardmethod of measuring the hardness of certain metals.The smooth surface of the metal is subject to inden-tation by a hardened steel ball under pressure orload. The diameter of, the resultant indentation, inthe metal surface, is measured by a special micro-scope and the Brinell hardness value read from achart or calculated by formula.

BROKEN SURFACE – Surface fracturing, generallymost pronounced at sharp corners and minutecracks on the surface of a drawn product normal tothe direction of drawing.

BRONZE – Primarily an alloy of copper and tin, butthe name is now applied to other alloys not contain-ing tin; e.g. aluminum bronze, manganese bronze,and beryllium bronze.

BURR – A thin ridge or roughness left by cuttingoperation such as in sawing, metal slitting, shearing,or blanking. Burrs are common on almost every cutpiece of steel.

CAMBER – Curvature of a straight plane. Not to beconfused with a bow. Standard steel industry toler-ance for camber is 1/8” in 5 feet.

CARBON STEEL – A steel in which carbon is theonly alloying element added to the iron to control itsproperties; also known as ordinary steel, or straightcarbon steel; or plain carbon steel.

CARBURIZING – Adding carbon to the surface ofiron-base alloys by absorption through heating themetal at a temperature below its melting point incontact with carbonaceous solids, liquids or gases.The oldest method of case hardening.

CASE HARDENING – A heat treatment or combina-tion of heat treatments by which the surface layer ofsteel is made harder than the interior. The processesof carburizing, nitriding, and cyaniding accomplishthis result by changing the composition of the case.

CASTING – The metal shape that is obtained as aresult of pouring metal into a mold or cavity andallowing it to harden so that it will assume and retainthe size and shape of the mold/cavity when cold.

CHARPY TEST – A notched-bar or impact test inwhich a notched specimen, fixed at both ends, isstruck behind the notch by a striker carried on apendulum. This test is used to determine how manypounds of pressure will cause the part to break, orhow many pounds the part can withstand.

CHATTER – An uneven surface on drawn productsusually formed by vibration of the metal during draw-ing.

CHROMIUM – Element No. 24 of the periodic sys-tem; atomic weight 52.01. It is of bright silvery color,relatively hard. It is strongly resistant to atmosphericand other oxidation. It is of great value in the manu-facture of Stainless Steel as an iron-base alloy.Chromium plating has also become a large outlet forthe metal. Its principal functions as an alloy is steelmaking; (1) increase resistance to corrosion and oxi-dation; (2) increases hardenability; (3) adds somestrength at high temperatures; (4) resists abrasionand wear (with high carbon).

CHROMIUM-NICKEL STEEL – Steel usually madeby the electric furnace process in which chromiumand nickel participate as alloying elements. Thestainless steel of 18% chromium and 8% nickel arethe better known of the chromium-nickel types.

COILS – Coiled flat sheet or strip metal – usually inone continuous piece or length.

COLD DRAWING – Permanent deformation of metalbelow its recrystallization temperature, by drawingthe bar through one or more dies.

COLD FINISH – The term “Cold Finish” is anumbrella definition for any material that has hadsome sort of surface treatment. Ex: Cold Drawn iscold finish surface. Centerless Ground & SmoothTurned Rough Turned - these are all “Cold Finish”Ex: S# 49050 HR T 4” RD 4340 is considered a coldfinished product because the surface has beenturned.

COLD REDUCTION – Reduction of metal size, usu-ally by rolling or drawing particularly thickness whilethe metal is maintained at room temperature ofbelow the recrystallization temperature of the metal.

COLD ROLLED FINISH – Finish obtained by coldrolling plain pickled sheet or strip with a lubricantresulting in a relatively smooth appearance.




(562) 802-2721



[email protected]

(562) 802-2721

COLD ROLLING – Rolling metal at a temperaturebelow the softening point of the metal; to createstrain hardening (work-hardening). Same as coldreduction, except that the working method is limitedto rolling. Cold rolling changes the mechanical prop-erties of strip and produces certain useful combina-tions of hardness, strength, stiffness, ductility andother characteristics known as tempers.

COLD WORKING – Plastic deformation of a metal ata temperature low enough to insure strain (work)hardening. In the 300 series (that cannot be heattreated to increase the hardness) it can go throughthis cold working process, at time of manufacturing,to increase the physical properties.

CONCENTRICITY – Center to the end of the circle.All round bars have three tolerances to consider;size, straightness and out of round. The ‘out ofround’ tolerance could effect the concentricity of abar. Fry Steel’s stock list advises “it is not advisableto try to finish on size from the size purchased.”

CONSTITUENT – A necessary part or element;component.

CONSUMET – Carpenters trade name for “con-sumable electrode vacuum melt.”

CONTINUOUS FURNACE – Furnace, in which thematerial being heated moves steadily through thefurnace.

CORROSION – Gradual chemical or electrochemi-cal attack on a metal by atmosphere, moisture orother agents.

CREEP – Slow permanent deformation in a metallicspecimen produced by a relatively small steadyforce, below the elastic limit, acting for a long periodof time.

CRITICAL RANGE – A temperature range in whichan internal change takes place within a metal. Alsotermed transformation range.

CRUCIBLE – A ceramic pot or receptacle made ofgraphite and clay, or clay or other refractory materi-al, and used in the melting of metal. The term issometimes applied to pots made of cast iron, caststeel, or wrought steel.

DEBURRING – A method whereby the raw slit edgeof metal is removed by rolling or filing.

DECARBURIZATION – Removal of carbon from theouter surface of iron or steel, usually by heating in anoxidizing or reducing atmosphere. Water vapor, oxy-gen and carbon dioxide are strong decarbuizers.

Reheating with adhering scale is also strongly decar-burizing in action.

DEGASSING PROCESS – (in steel making)Removing gases from the molten metal by means ofa vacuum process in combination with mechanicalaction.

DRAWING – The process of pulling material througha die to reduce the size, change the cross sectionalshape, or to harden the material.

DRAWING BACK – Reheating after hardening to atemperature below critical for the purpose of chang-ing the hardness of the steel (see Tempering).

DRAWN-IN-SCRATCHES – Scratches which occurduring the fabricating process and are subsequentlydrawn over. They are characterized by a drawingover the scratch which makes it relatively smooth tothe touch.

DRILL ROD – A term given to an annealed and pol-ished high carbon tool steel rod usually round andcenterless ground. The sizes range in round stockfrom .013 to 1-1/2” diameter. Commercial qualitiesembrace water and oil hardening grades. A lesspopular but nevertheless standard grade is non-deforming quality. Drill Rods are used principally bymachinists and tool and die makers for punches,drills, taps, dowel pins, screw machine parts, smalltools, etc.

DROP FORGING – The process of shaping metalparts by forging between two dies, one fixed to thehammer and the other to the anvil of a steam ormechanical hammer. It is used for mass productionof such parts as connecting rods, crankshafts, andsimilar articles.

DUCTILITY – The property of metals that enablesthem to be mechanically deformed when cold, with-out fracture. In steel, ductility is usually measured byelongation and reduction of area is determined in atensile test.

E T D – Elevated Temperature Drawn. OurStressproof is this type of material. The bars are coldworked and stress relieved as they are drawnthrough the dies to size them. We achieve a tensilearound 130,000 on our stressproof.

ELECTRIC FURNACE STEEL – Steel made in anyfurnace where heat is generated electrically, almostalways by arc. Because of relatively high cost, onlytool steels and other high-value steels are made bythe electric furnace process.




(562) 802-2721

ELECTROSLAG REMELT – This process produceshigh purity metals. The electrode to be refined isremelted by passing a current through it into amolten slag, which is resistively heated and which inturn melts the electrode. Molten metal forms on theend of the electrode and fall through the slag, form-ing an ingot in a water cooled crucible. The processcontinues until the electrode is consumed and thenewly formed ingot is complete. The slag essentiallycleans and purifies the metal up when it passesthrough it. Nitrides will not pass through the sludgewith low temps and times. Materials produced bythe ESR technique exhibit better property levels and,more significantly, less scatter in these properties. Inaddition the hot workability of superalloys whichwere not previously forgeable can be processed inthat manner after ESR.

ELONGATION – Increase in length which occursbefore a metal is fractured, when subjected tostress. This is usually expressed as a percentage ofthe original length and is a measure of the ductility ofthe metal.

EXTRUSION – Shaping metal into a chosen contin-uous form by forcing it through a die of appropriateshape.

FATIGUE – The phenomenon leading to fractureunder repeated or fluctuating stress. Fatigue frac-tures are progressive beginning as minute cracksand grow under the action of fluctuating stress.

FERROALLOY – An alloy of iron with a sufficientamount of some element or elements such as man-ganese, chromium, or vanadium for use as a meansin adding these elements into molten steel.

FERROUS – Related to iron. Ferrous alloys are ironbase alloys.

FINE GRAIN STEEL – Steels which resist graingrowth over a considerable temperature range,when held at temperature for a reasonable length oftime as is customary in heat treatment of steel.

FRACTURE TEST – A test for carbon in which aspecimen of metal is drawn off, cooled rapidly inwater, and broken with a sledge hammer. Theappearance of the metal exposed in the fracture per-mits a fairly accurate estimate of carbon content orthe presence of internal defects.

FREQUENCY & SEVERITY – Ratings for inclusionsand stringers, as allowed per each individual gradespecification. How many inclusions per square inch= frequency. What is the length of the inclusions per

square inch = severity. The ideal F/S rating would be“0/0”. Each grade of steel has its own F/S.

Examples: 1018 & 4130 can have up to 1” lengthseverity

Type 15-5 5/64” length severityType 13-8 3/64” length severity

FULL ANNEALING – Heating iron-base alloysabove the critical temperature range, holding thealloy above that range for a proper period of timeand then slowly cooling it to below the range eitherin the furnace or in some thermal insulating material.

GAS CARBURIZING – A method of carburizingcarried out in an atmosphere of carburizing gases,including carbon monoxide and hydrocarbons asbutane, ethane, methane, and propane.

GRAIN – Individual crystals in metals. A solid poly-hedral (or many sided crystal) consisting of groupsof atoms bound together in a regular geometric pat-tern. In mill practice grains are usually studied onlyas they appear in one plane (1) (Direction of,) Refersto grain fiber following the direction of rolling andparallel to edges of strip or sheets; (2) To bendacross the grain is to bend at right angles to thedirection of rolling; (3) To bend with the grain is tobend parallel to the directions of rolling. In steel, theductility in the direction of rolling is almost twice thatat right angels to the direction of rolling.

GRAIN BOUNDARY – Bounding surface betweencrystals. When alloys yield new phases (as in cool-ing) grain boundaries are the preferred location forthe appearance of the new phase. Certain deteriora-tions such as season cracking and caustic embrittle-ment, occur almost exclusively at grain boundaries.

GRAIN GROWTH – An increase in the average grainsize resulting from some crystals absorbing adjacentones when the metal is raised to a temperatureabove that necessary for recrystallization and kept atthat temperature for a sufficient length of time.

GRAIN SIZE – Average diameter of grains in themetal under consideration, or alternatively, the num-ber of grains per unit area. Since increase in grainsize is paralleled by lower ductility and impact resist-ance the question of general grain size is of greatsignificance. The addition of certain metals affectsgrain size, for example vandium and aluminum tendto give steel a fine grain. The ASTM has set up agrain size standard for steels, and the McQuaid-EhnTest had been developed as a method of measure-ment.



[email protected]

(562) 802-2721

H-STEELS – Steels made under specifications thatinclude hardenability tolerance.

HARDENABILITY – The ability of metal, usuallysteel, to harden in depth as distinguished from theterm “hardness.” The depth to which steel can behardened to martensite under stated conditions ofcooling.

HARDNESS – Degree to which metal will resist cut-ting, abrasion, penetration, bending and stretching.The indicated hardness of metals will differ some-what with the specific apparatus and technique ofmeasuring. For details concerning the various typesof apparatus used in measuring hardness, seeBrinell Hardness and Rockwell Hardness. TensileStrength also is an indication of hardness.

HEAT OF STEEL – The product of a single meltingoperation in a furnace, starting with the charging ofraw materials and ending with the tapping of moltenmetal and consequently identical in its characteris-tics.

HEAT TREAT STAIN – Discoloration of the metalsurface caused by oxidation during thermal treat-ment.

HEAT TREATMENT – Altering the properties of ametal by subjecting it to a sequence of temperaturechanges, time of retention at specific temperaturesand rate of cooling therefrom being as important asthe temperature itself. Heat treatment usuallymarkedly affects strength, hardness, ductility, mal-leability, and similar properties of both metals andtheir alloys.

HIGH-SPEED TOOL STEEL – A hard steel used tomake tools that can cut while red hot and running athigh speeds. It permits fast working and deep cutswhile hot.

HIGH TENSILE – Using external pressure toincrease the hardness (physical properties). Drawingmaterial through a die will create a high tensile bar.Cold working is a term used in conjunction with hightensile. In the stainless grade, this is also referred toas “Condition B.”

HOT WORKING – Work carried out at a temperatureat or above the recrystallization temperature of themetal in question. During hot working, the grains areconstantly being deformed and broken up, but newones are constantly forming to take their place.Plastic deformation of metal at a temperature suffi-ciently high not to create strain hardening. The lowerlimit of temperature for this process is the recrystal-lization temperature.

HYPERM 49 – Carpenters trade name for 4750.

IMPACT TEST – Test designed to determine theresistance of metals to breakage by impact, usuallyby concentrating the applied stress to a notchedspecimen. Results usually are express in terms ofenergy absorbed or number of blows (of a giveintensity) required to break the specimen. Izodimpact or charpy impact are the common methodsof studying impact resistance.

INCLUSIONS – Particles of impurities (usuallyoxides, sulfides, silicates, etc.) that are heldmechanically or are formed during the solidificationor by subsequent reaction within the solid metal.

INDENTATION HARDNESS – The resistance of amaterial to indentation. This is the usual type ofhardness test, in which appointed or rounded inden-ter is pressed into a surface under a substantiallystatic load.

INDUCTION HARDENING – A surface hardeningprocess based upon the heating effect produced ina piece of steel by placing it in a high-frequencyelectric field generated in a suitable shaped water-cooled coil of copper wire of tubing.

INGOT – Metal casting of uniform sizes and shapesfor subsequent rolling, forging, or processing.

INGOT IRON – An open-hearth product low in car-bon, manganese, and impurities.

INTERNAL STRESS – A residual stress that mayexist between different parts of metal products as aresult of the differential effects of heating, cooling,working operations, or of constitutional changes inthe solid metal. It may be relieved by heating to a lowtemperature without affecting the mechanical prop-erties.

IZOD TEST – A notched-bar or impact test in whicha notched specimen held in a vise is struck on theend by a striker carried on a pendulum; the energyabsorbed in fracture is obtained from the height towhich the pendulum rises.

JOMINY TEST – A standardized procedure bywhich the hardenability of a steel is determined.

KILLED STEEL – The terms “killed” indicated thatmolten steel is held in a ladle, furnace, or crucible(and usually treated with aluminum, silicon, or man-ganese) until no more gas is evolved and the metalis perfectly quiet, when the molten metal is pouredinto the ingot mold. A properly killed steel is moreuniform as to analysis and is comparatively free fromaging. In general all steels above 0.25% carbon arekilled, also all forging grades, structural steels from0.15% to 0.25% carbon and some special steels inthe low carbon range.

KINK – Small creases or indentations caused bylocalized bending during handling, etc.

LADLE – A vessel lines with refractory material; usedfor conveying molten metal from the furnace to themold or from one furnace to another.

LADLE ANALYSIS – A term applied to the chemicalanalysis representative of a heat of steel as reportedby the producer. It is determined by analyzing a testingot sample obtained during pouring the steel froma ladle.

LAMINATIONS – Internal cracks aligned parallel tothe worked surface of the metal.

LAP – A continuous longitudinal defect caused bymetal folding back on its own surface. A surfacedefect appearing as a seam, caused by folding overhot metal, fins or sharp corners and then rolling orforging them into the surface, but not welding them.

LONGITUDINAL DIRECTIONS – The principaldirection of flow in a worked metal. Usually thelength of the bar. Grain direction also runs the lengthof the bar.

LOW CARBON STEELS – Contain from 0.10% to0.30% carbon and less than 0.60% manganese (Theproduct of Basic Oxygen, Bessemer, Open Hearth orElectric Processes).

MACHINABILITY – A property of metals that per-mits them to be cut, turned, broached, or otherwiseformed by machine tools. The relative ease ofmachining a metal. The machinability rating is usual-ly reported in “Surface feet per minute.”

MACHINE FINISH ALLOWANCE – The allowancemade for machining the finished part.

MACROETCH TEST – Consists of immersing acarefully prepared section of the steel in hot acid andof examining the etched surface to evaluate thesoundness and homogeneity of the product beingtested.

MACROGRAPH – A photographic reproduction ofany object that has not been magnified more thanten times.

MACROSCOPIC – Visible either with the naked eyeor under low magnification (as great as about tendiameters.)

MACROSTRUCTURE – The structure of metal asrevealed by macroscopic examination of the etchedsurface of a polished specimen at a magnification(as great as about ten diameters.)

MAG QUALITY – Material that has had stockremoval performed to insure that the material is freefrom any seams or non-metallic inclusions locatedon or immediately below the surface. This test isused on all Type 400 & PH Grades. 200 & 300 steelscannot be tested. This is normally performed onmaterial that is magnetic.

MAGNAFLUX TEST – A magnetic test used todetect defects on or near the surface of metals.

MAGNETIC-PARTICLE INSPECTION – A nonde-structive method of inspection for determining theexistence and extent of possible defects in ferro-magnetic materials. Finely divided magnetic parti-cles, applied to the magnetized part, are attracted toand outline the patterns of any magnetic-leakagefields created by discontinuities.

MAGNETIC PERMEABILITY – The ratio of the mag-netic induction of a substance to the magnetizingfield to which it is subjected.

MALLEABILITY – The property that determines theease of deforming a metal when the metal is subject-ed to rolling or hammering. The more malleable met-als can be hammered or rolled into thin sheet moreeasily than others.

MARTENSITE – A distinctive needlelike structureexiting in steel as a transition stage in the transfor-mation of austenite. It is the hardest constituent ofsteel of eutectoid composition. It is produced byrapid cooling from quenching temperature and is thechief constituent of hardened carbon tool steels.Martensite is magnetic.

MARTENSITIC STEEL – Steel which has martensiteas its chief constituent after cooling in air. The hard-enable stainless types are all martensitic steels. Anexample of martensitic steel is the 400 series.

MECHANICAL PROPERTIES – Properties of ametal determining its behavior under stress. Thoseproperties of a material that reveal elastic and inelas-tic reaction when force is applied, or that involve therelationship between stress and strain; for example,the modulus of elasticity, tensile strength and fatiguelimit. These properties have often been designatedas “physical properties” but the term “mechanicalproperties” is much to be preferred. The mechanicalproperties of steel are dependent on its microstruc-ture.

METALLURGIST – A technically trained person whohas specialized in that science which deals with theseparation of metals from the earthy materials withwhich they are combined.




(562) 802-2721



[email protected]

(562) 802-2721

METALLURGY – The art and science of extractingmetals from their ores and other metal-bearing prod-uct and adapting these metals for human utilization.

MICROSCOPIC – Visible under a magnification ofabout 10 diameters or more.

MICROSTRUCTURE – The structure and internalcondition of metal as revealed in polished and usu-ally etched metal samples when examined under amicroscope.

MILL EDGE – The edge of strip, sheet or plate in theas rolled state. Unsheared.

MOLD – A form of cavity into which molten metal ispoured to produce a desired shape.

NITRIDING – Process of surface hardening certaintypes of steel by heating in ammonia gas at about935-1000 F., the increase in hardness being theresult of surface nitride formation. Certain alloyingconstituents, principal among them being aluminumgreatly facilitate the hardening reaction. In general,the depth of the case is less than with carburizing.

NITRIDING STEEL – Steel which is particularly suit-ed for the nitriding process, that is, it will form a veryhard and adherent surface upon proper nitriding(heating in a partially dissociated atmosphere ofammonia gas). Composition usually .20-.40 carbon.90-1.50 chromium, .15-1.00 molybdenum, and .85-1.20% aluminum.

NON-FERROUS METALS – Metals or alloys that arefree of iron or comparatively so.

NONFILLS – Nonfilling of roll cavity causing incom-plete section or deviation from expected contour.

NON-METALLIC INCLUSIONS – Impurities (com-monly oxides), sulphides, silicates or similar sub-stances held in metals mechanically during solidifi-cation or formed by reactions in the solid state.

NORMALIZED – Material (alloy) that is cooled in“open air,” not a controlled cooling process. Thisprocedure is quicker and cheaper than annealing,because you don’t tie up a furnace. Material that isnormalized may not have a uniform hardness.Characteristics would be “hard spots” and a higheras shipped hardness than an annealed bar. Is per-formed to refine the crystal structure and eliminateinternal stress.

NORMALIZED & TEMPERED – This is an abbrevia-tion for the correct heading Normalized and SubCritical Annealed. This means: if a customer calls

and asks for “Annealed” you can expand their state-ment by telling them that this material is a subcriticalannealed material, so it can be considered anannealed product. The first operation is the normal-izing, which gives the material a certain grain struc-ture and then sub critically annealed, which furtherenhances the grain structure and puts it in an excel-lent position to be heat treated (aka: hardened).Norm & Temp (Subcritical annealed) is a processwhere the mill controls the maximum as shippedhardness. You will hear “normalized & tempered toRC 33 max.” RC 33 is the maximum hardness themill aims for, for the material (alloy) to still be consid-ered annealed.

OFF GAGE – Dimension outside the specified toler-ances.

OIL HARDENING – A process of hardening a ferrousalloy of suitable composition by heating within orabove the transformation range and quenching in oil.

OIL-HARDENING STEEL – Steel adaptable to hard-ening by heat treatment and quenching in oil.

OIL STAIN – Stains produced by the incompleteburning of lubricants on the surface of a product.Drawing subsequent to staining will change colorfrom darker browns to lighter browns down to white.

OPEN-HEARTH PROCESS – Process of makingsteel by heating in a refractory-lines, shallow-bath,rectangular furnace in which both hearth and chargeare subjected to direct action of the fuel flame. Thefuel may be produced gas, natural gas, coke ovengas, powdered coal or oil.

ORANGE PEEL – A surface roughening encoun-tered in forming products from material which has acoarse grain size.

OVERAGING – Aging under conditions of time andtemperature greater than those required to obtainmaximum strength.

OXIDATION – The addition of oxygen to a com-pound. Exposure to atmosphere sometimes resultsin oxidation of the exposed surface, hence a stainingor discoloration. This effect is increased with tem-perature increase.

OXIDE – Compound of oxygen with another ele-ment.

PASSIVATION – The changing of the chemicallyactive surface of a metal to a much less reactivestate.

PENETRANT INSPECTION – A method of non-destructive testing for determining the existence andextent of discontinuities that are open to the surfacein the part being inspected. The indications aremade visible through the use of a dye or fluorescentchemical in the liquid employed as the inspectionmedium.

PHYSICAL PROPERTIES – Those properties famil-iarly discussed in physics, exclusive of thosedescribed under mechanical properties; for exam-ple, density, electrical conductivity, co-efficient ofthermal expansion. This term often has been used todescribe mechanical properties, but this usage isnot recommended.

PICKLING – The process of chemically removingoxides and scale from the surface of a metal byimmersion in a diluted acid bath so as to obtain achemically clean surface preparatory to cold rollingor wire drawing.

PIPE – (Defect) A shrinkage cavity formed in metal(especially ingots) during solidification of the lastportion of liquid metal. Contraction of the metalcauses this cavity or pipe. Contraction cavity, essen-tially cone-like in shape, which occurs in the approx-imated center, at the top and reaching down into acasting; caused by shrinkage of cast metal.

POLISHING – A mechanical finishing operation forthe purpose of applying a gloss or luster to the sur-face of a product.

POROSITY – State of being porous. The morestringers and inclusions involved, the higher theporosity.

PRECIPITATION HARDENING – The phenomenonwhich results in an increase in hardness with thepassage of time at room or elevatedtemperature.The increase is produced by a changein structure associated with precipitation of a con-stituent from solid solution along the grain bound-aries.

PRECIPITATION HEAT TREATMENT – (Nonferrousmetal) Any of the varoius aging treatments conduct-ed at elevated temperatures to improve certain ofthe mechanical properties through precipitation fromsolid solutions.

PROCESS ANNEALING – Same as subcriticalannealing.

PYROMET 680 – Carpenter’s trade name forHastelloy X (Fry Alloy X).

PYROMETER – An instrument, of any various types,used for measuring and determining elevated tem-perature.

QUENCHING – Rapid cooling of steel from abovethe critical range by immersion in liquids or gases, orby contact with metal, in order to harden it.

QUENCH CRACKS – Surface cracks in metal whichoccur on quenching, due to improper heat-treatingpractices.

QUENCH HARDENING – (Steel) A process of hard-ening a ferrous alloy of suitable composition byheating within or above the transformation rangeand cooling at a rate sufficient to increase the hard-ness substantially. The process usually involved theformation of martensite.

R C S – Round Corner Square.

R M S – A rating used on the finish of a ground bar.Normally called out as a “micro” . The smaller thenumber, the finer the grain.

RECRYSTALLIZATION – Formation of new crystalsor grains from deformed metal, accomplished bysuitable heat treatment.

REDUCTION OF AREA – (1) Commonly, the differ-ence, expressed as a percentage of original area,between the original cross-sectional area of a tensiletest specimen and the minimum cross-sectionalarea measured after complete separation. (2) Thedifference, expressed as a percentage of originalarea, between original cross-sectional area and thatafter straining the specimen.

REPHOSPHORIZING – (Steel) A ladle-chemicaltreatment consisting of the addition of phosphorusas a work hardening agent when temper rolling blackplate or sheet steel resulting in greater hardness andstiffness and with a corresponding loss in ductility.

RESIDUAL STRESS – Macroscopic stresses thatare set up within a metal as the result of nonuniformplastic deformation. This deformation may becaused by cold working or by drastic gradients ortemperature from quenching or welding.

RESIDUALS – “Incidental”elements not names inspecification. These inclusions are usually dueto contaminated scrap.




(562) 802-2721



[email protected]

(562) 802-2721

ROCKWELL HARDNESS (TEST) – A standardmethod for measuring the hardness of metals byindenting them with a hard steel ball or a diamondcone under a specified load, measuring the depth ofpenetration, and subtracting the latter from an arbi-trary constant. Rockwell hardness numbers arebased on the difference between the depths of pen-etration at major and minor load; the greater this dif-ference, the less the hardness number. This residualpenetration is automatically registered on a dialwhen the major load is removed from the penetrator.Various dial readings combined with different majorloads, give “scales” designated letters varying from“A” to “H”; “B” and “C” scales are most commonlyin use.

RODS – Wire rods are semifinished hot-rolledrounds of great lengths, usually coiled, and usedprincipally for drawing to wire.

ROLLING – A term applied to the operation of shap-ing and reducing metal in thickness by passing itbetween rolls which compress, shape and lengthenit following the roll pattern.

ROLLING MILLS – Mills in which a preheated steelingot is passed between heavy chilled cast sheetrolls.

ROLLED-IN-METAL – An extraneous chip or sliverof metal rolled into the surface of the rod or bar.

ROLLED-IN-SCRATCHES – Scratches which occurduring the fabricating process and are subsequentlyrolled over. They are characterized by a rolling-overof the scratch which makes it relatively smooth tothe touch.

ROUGH MACHINING – Machining without regard tofinish, usually to be followed by a subsequent oper-ation.

RUBMARK – A minor form of scratching consistingof areas made up of a large number of very finescratches or abrasions.

SAE – Abbreviation for Society of AutomotiveEngineers. This organization has specified commonand alloy steels and copper base alloys in accor-dance with a numerical index system allowingapproximation of the composition of the metal. Thelast two digits always indicate the carbon content,usually within 0.05%.

SCRATCH – A mark on the surface of the productproduced by scratching. Such marks are generallyrough to the touch.

SEAM – (A defect) On the surface of metal a crackthat has been closed but not welded; usually pro-

duced by some defect either in casting or in workingsuch as blowholes that have become oxidized orfolds and laps that have been formed during work-ing.

SEGREGATION – Nonuniform distribution of impuri-ties, inclusions, and alloying constituents in metals.

SEMIFINISHED STEEL – Blooms, billets, slabs,sheet bars, rods, and other product.

SHEAR STRENGTH – The stress required to pro-duce fracture in the plane of cross section, the con-ditions of loading being such that the directions offorce and of resistance are parallel and oppositealthough their paths are offset a specified minimumamount.

SHIM – A thin flat hard metal strip produced to closetolerances; used primarily for tool, die and machinealignment purposes.

SINTERING – Converting powder into a continuousmass by heating to a temperature considerablebelow fusion, usually after preliminary compactingby pressure.

SLAB – An ingot reduced, generally by rolling, to athickness better suited to the operation that follows.A slab, as distinguished from a bloom, has width atleast twice its thickness and a minimum thickness of1-1/2 inches. It is re-rolled to plates and to sheet bar.Slabs are classified as semifinished products.

SLAG – A nonmetallic covering on molten metal asthe result of the combining of impurities contained inthe original charge, some ash from the fuel, and anysilica and clay eroded from the refractory lining.Except in bottom-pour ladles it is skimmed off priorto pouring the metal.

SLIVER – Slender fragments or splinters which arean integral part of the material but which are incom-pletely attached to the metal.

SOAKING PIT – An underground furnace in which astripped ingot is heated or soaked in heat until it isuniformly heated throughout to its rolling tempera-ture.

SOLUTION HEAT TREATMENT – A process inwhich an alloy is heated to a suitable temperature, isheld at this temperature long enough to allow a cer-tain constituent to enter into solid solution and isthen cooled rapidly to hold the constituent in solu-tion. The metal is left in a supersaturated, unstablestate and may subsequently exhibit age hardening.




(562) 802-2721

SPARK TEST – Classification of steels according totheir chemical analysis by visual examination of thesparks thrown off when the steels are held against ahigh-speed grinding wheel.

SPECTROGRAPH – An optical instrument for deter-mining the presence or concentration of minormetallic constituents in a material indicating thepresence an intensity of specific wave lengths ofradiation when the material is thermally or electrical-ly excited.

SPHEROIDIZING – Any process of prolonged heat-ing and slow cooling of steel which will convert thecarbide content into rounded or spheroid form.

SPRING STEEL – Steel, normally of the high-carbonor alloy type, used in the manufacture of springs,lending itself to appropriate heat treatment; usuallymade in the open hearth or electric furnace.

STABILIZING TREATMENT – A thermal treatmentdesigned to precipitate material from solid solution,in order to improve the workability, to decrease thetendency of certain alloys to age harden at roomtemperature, or to obtain dimensional stability andservice at slightly elevated temperatures.

STAINLESS STEEL – Corrosion resistant steel of awide variety, but always containing a high percent-age of chromium. These are highly resistant to cor-rosion attacked by organic acids, weak mineralacids, atmospheric oxidation, etc.

STAMPING – A term used to refer to various pressforming operation in coining, embossing, blanking,and pressing.

STEEL – Iron, malleable in at least one range of tem-perature below its melting point without special heattreatment, substantially free from slag, and contain-ing carbon more than about 0.05% and less thanabout 2.00%. Other alloying elements may be pres-ent in significant quantities, but all steels contain atleast small amounts of manganese and silicon, andusually as undesirable constituents, also sulfur andphosphorus.

STELLITE – A series of alloys containing cobalt,chromium, tungsten, and molybdenum in variouscompositions. Stellites are used for high-speed cut-ting tools and for protecting surfaces subjected toheavy wear.

STOCK REMOVAL – This is a designated or prede-termined amount of material to be removed from thesurface or surfaces of the bar stock. Fry Steel liststhese amounts of stock removal in our Stock List.Refer to these charts. The idea being that, usuallythe larger the size, the more stock removal is

required. Hot rolled and Cold Drawn surfaces, mustalways have some stock removal prior to anyinspection or heat treating. If the customer choosesnot to do the recommended stock removal, it is attheir own risk. On the other finished, CG, PG, ST andRT, the customer does not have to remove surfacestock prior to heat treating or surface inspection,The exception being, if the inspection specificationrequires surface removal, then this must be doneaccording to that specification. Fry’s turned surface(CG PG ST RT) materials are guaranteed to be freefrom surface lapse, cracks and seams.

STRESS RELIEF – Heating to a suitable tempera-ture, holding long enough to reduce residual stress-es and then cooling slowly enough to minimize thedevelopment of new residual stresses. A thermaltreatment in which the lock-up stresses in a barcaused by cold working are removed by heating thebar close to but below the lower limit of the criticaltemperature range, or to approximately 100°F belowthe tempering temperature.

STRESS-RUPTURE TEST – A tension test per-formed at constant temperature, the load being heldat such a level as to cause rupture. Also known as“creep-rupture test.”

STRAIGHTNESS TOLERANCE – In the steel indus-try, the standard straightness tolerance is 1/8 inchper 5 feet.

STRINGERS – A form of inclusion normally causedby the banding together of elements within thematerial. (Example: In Grade 321 the titanium does-n’t mix well and tends to clump together, thus 321has inherent titanium stringers.)

STRAIN HARDENING – An increase in hardnessand strength caused by plastic deformation at tem-perature lower than the recrystallization range.

SUBCRITICAL ANNEALING – Heat steel to a tem-perature below its critical temperature, and subse-quently cooling at a rate dependent upon the carboncontent; also called process annealing.



[email protected]

(562) 802-2721

TEMPER – The state of or condition of a metal as toits hardness or toughness produced by either ther-mal treatment or heat treatment and quench or coldworking or a combination of same in order to bringthe metal to its specified consistency. Each branchof the metal producing industry has developed itsown system or temper designations.

TEMPERING – A process of reheating quench-hard-ened or normalized steel to a temperature below thetransformation range and then cooling at any ratedesired. The primary purpose of tempering is todecrease the hardness and impart a degree of plas-ticity or toughness to the steel to alleviate the brittle-ness of its martensite.

TENSILE STRENGTH – Breaking strength of amaterial when subjected to a tensile (stretching)force. Usually measured by placing a standard testpiece in the jaws of a tensile machine, gradually sep-arating the jaws, and measuring the stretching forcenecessary to break the test piece. Tensile strength iscommonly expressed as pound (PSI) per squareinch of original cross section.

TENSILE TEST – Application of a pulling force to aspecimen of material and measurement of the reac-tions that occur. In steel, these reactions occur intwo distinct phases; the elastic phase wherein thematerial is not permanently deformed by the pullingforce, and the plastic or yield phase wherein thematerial becomes either permanently deformed orruptured.

TOLERANCE – Allowable deviation from a specifieddimension.

Close Tolerance - Any Special Tolerance thatis closer than Standard.

Commercial Tolerance - This term is some-times used synonymously with “StandardTolerance.” In such cases the term “StandardTolerance” is preferred.

Published Tolerance - This term is some-times used synonymously with “StandardTolerance.” In such cases the term “StandardTolerance” is preferred.

Special Tolerance - Any tolerance that iscloser or wider than Standard.

Standard Tolerance - An established toler-ance for a certain class of product. This terms is pre-ferred to “Commercial” or “Published” tolerance.

Wide Tolerance - Any Special Tolerance thatis wider than Standard Tolerance.

TOOL STEEL – Any high carbon or alloy steel capa-ble of being suitably tempered for use in the manu-facture of tools.

TOUGHNESS – Property of resisting fracture or dis-tortion. Usually measured by impact test, highimpact values indicating high toughness.

TORN SURFACE – A deep longitudinal rubmarkresulting from abrasion by tools.

TRAFFIC MARKS – Abrasions which result frommetal or metal contact and vibration during transit.These abrasions are usually dark in appearancebecause of the presence of a dark powder consist-ing of aluminum and aluminum oxide.

TRANSVERSE – Literally, “across” usually signifyinga direction or plane perpendicular to the direction ofworking.

TREPANNING – A type of cutting/boring/drillingprocedure done down the middle of a solid bar. Theend result produces a tube or pipe from what wasonce a solid bar. Gun makers use this procedure tomake gun barrels. After the trepanning process iscompleted, a core formation (aka: a plug, solid cylin-der, or core comes out of the middle of the bar,instead of metal chips that are the result of drilling.

TWIST – A winding departure from flatness.

VACUUM MELTING – Melting in a vacuum to pre-vent contamination from air, as well as to removegases already dissolved in the metal; the solidifica-tion may also be carried out on a vacuum or at lowpressure.

VACUUM ARC REMELTING – A vacuum-arc-remelting furnace consists mainly of two parts -upper electrode housing and lower crucible assem-bly. The electrode can be lowered or raised withoutbreaking the vacuum. The water-cooled crucibleforms the mold. Cast or forged electrodes, meltedby any suitable process, are consumably remeltedby any suitable process, are consumably remelted atpressures from 1 to 50 microns. During the process,the metal transfers from the electrode to the mold asa uniform flow of superheated fine spray and col-lects in a molten pool. The ingot solidifies progres-sively from bottom to top. As a result, the centerporosity and segregation normally found in static-cast ingots are minimized. Near the end of the melt-ing, power is gradually reduced to produce a mini-mum of shrinkage cavity. Degassification, dissocia-tion, and deoxidation take place to various degreesboth during the transfer of metal from the electrodeto the ingot and in the molten pool.




(562) 802-2721

VICKERS HARDNESS – (Test) Standard method formeasuring the hardness of metals, particularly thosewith extremely hard surfaces; the surface is subject-ed to a standard pressure for a standard length oftime by means of pyramid-shape diamond. Thediagonal of the resulting indention is measuredunder a microscope and the Vickers Hardness valueread from a conversion table.

VIM VAR – Double Vac Melt process (Example: Fry’sGrade 13-8) Vacuum induction melt plus vacuum arcremelt.

WATER HARDENING STEELS – Low-carbon andlow-alloy steels that must be quenched in water forhardening.

WATER STAINS – A superficial etching of the sur-face from prolonged contact with moisture in arestricted air space such as between the layers ofthe product. Such stains are generally white inappearance.

WELDABILITY – The case with which simple metalparts made of similar and dissimilar metals may bejoined together in order to form complicated struc-tures.

WELDING – A process used to join metals by theapplication of heat. Fusion welding, which includes

gas, arc, and resistance welding, requires that theparent metals be melted. This distinguishes fusionwelding from brazing. In pressure welding joining isaccomplished by the use of heat and pressure with-out melting. The parts that are being welded arepressed together and heated simultaneously, so thethat recrystallization occurs across the interface.

WORK HARDENING – Hardening that takes placein a metal when work of any sort, such as bending,rolling, hammering, drawing, punching, and the like,is done at a temperature below that at which recrys-tallization takes place. Increase in resistance todeformation (i.e. in hardness) produced by coldworking.

YIELD POINT – The load per unit at original crosssection at which, in soft steel, a marked increase indeformation occurs without increase in load.

YIELD STRENGTH – The load per unit area at whicha material exhibits a specified permanent deforma-tion or a specified elongation under load.

ZYGLO – A highly fluorescent nondestructive pene-trant inspection test applied to nonmagnetic materi-als to detect flaws.

DEFINITIONS FOR THE ALUMINUM INDUSTRY


[email protected]

(562) 802-2721

AMS – Abbreviations for Aerospace MaterialSpecification.

ANSI – Abbreviations for American NationalStandards Institute.

ASME – Abbreviations for American Society ofMechanical Engineers.

ASTM – Abbreviations for American Society forTesting and Materials.

AWS – Abbreviations for American Welding Society.

Abrasion – See “Mark, Traffic.”

Age Hardening – An aging process which results inincreased strength and hardness.

Age Softening – Spontaneous decrease of strengthand hardness that takes place at room temperature incertain strain hardened alloys containing magnesium.

Aging – Precipitation from solid solution resulting ina change in properties of an alloy, usually occurringslowly at room temperature (natural aging) and morerapidly at elevated temperatures (artificial aging).

Alclad – An aluminum or aluminum-alloy coating thatis metallurgically bonded to either one or both surfaces of an aluminum alloy product, and that isanodic to the alloy to which it is bonded, thus electrolytically protecting the core alloy against corrosion. For Alclad products, see specific productsuch as “Plate,” “Sheet,” “Tube,” or Wire.”

Alligatoring – See “Lamination.”

Alloy – A substance having metallic properties andcomposed of two or more elements of which at leastone is an elemental metal.

Angularity – Conformity to, or deviation from, specified angular dimensions in the cross section ofa shape or bar.

Angulation – The deliberate departure from a horizontal passline on the entry side of a rolling millused for one-side bright rolling.

Annealing – A thermal treatment to soften metal byremoval of stress resulting from cold working or bycoalescing precipitates from solid solution.

Annealing, Partial – Thermal treatment (H2X tempernomenclature) given cold worked metal to reducestrength and increase ductility to controlled levelsother than annealed temper.

Anodizing – Forming a coating on a metal surfaceproduced by electrochemical treatment throughanodic oxidation.

Anodizing Sheet – See “Sheet, Anodizing.”

Arbor Break – See “Buckle, Arbor.”

Arbor Mark – See “Mark, Arbor.”

Artificial Aging – See “Aging.”

Back End Condition – A condition occurring in thelast metal to be extruded. It is a result of the oxidizedsurface of the billet feeding into the extrusion.

Backup Rolls – Nongrooved rolls which stiffen orstrengthen work rolls.

Bar – A solid wrought product that is long in relationto its cross section which is square or rectangular(excluding plate and flattened wire) with sharp orrounded corners or edges, or is a regular hexagon oroctagon, and in which at least one perpendicular distance between parallel faces is 0.375 inch orgreater.

Bar, Cold Finished – Bar brought to final dimensionsby cold work to obtain improved surface finish anddimensional tolerances.

Bar, Cold-Finished Extruded – Cold-finished barproduced from extruded bar.

Bar, Cold-Finished Rolled – Cold-finished bar produced from rolled bar.

Bar, Extruded – Bar brought to final dimensions byhot extruding.

Bar, Rolled – Bar brought to final dimensions by hotrolling.

Bar, Saw-Plate – Bar brought to final thickness byhot or cold rolling and to final width by sawing.

Base Box-General – An agreed-upon unit of areaused primarily in packaging applications. One common base box for aluminum is 31,360 squareinches, originally composed of 112 rectangularsheets each 14 by 20 inches.

Belled Edge – See “Edge, Belled.”

Belly – A loose center buckle extending to near theedges of a sheet.

Billet – A hot worked semifinished product suitablefor subsequent working by such methods as rolling,forging, extruding, etc.

Blank – A piece of metal cut or formed to regular orirregular shape for subsequent processing such asby forming, bending or drawing. The piece of sheetstock cut out by blanking die. It will subsequently bedrawn into a cup or end shell.

Bleed Out – See “Two-Tone.”

Blister – A raised area on the surface of an extrudedproduct due to subsurface gas expansion. This canoccur during extrusion or thermal treatment.

Blister, Bond – A raised spot on only one surface ofthe metal whose origin is between the cladding andcore in clad products.

Blister, Coating – A blister in the coating of an alclador a clad product.

Blister, Core – A raised spot (one or both sides) onrolled metal.




(562) 802-2721

Block Mark – See “Scratch, Tension.”

Bloom – A semifinished hot rolled product, rectangular or square in cross section, produced on ablooming mill.

Blow Hole – A blister that has ruptured and may produce a void. See also “Blister.”

Boss – A knoblike projection on the main body of aforging or casting.

Bottom Draft – Taper or slope in the bottom of aforged depression to assist the flow of metal towardthe sides of the depressed area.

Bow – Longitudinal curvature of rod, bar, profiles(shapes), and tube. Bow is measured after allowingthe weight of the extrusion to minimize the deviation.Bow can be caused by a non-uniform extrusion rateacross the cross section resulting in one portion of theextrusion being longer than the other or non-uniform contraction during quenching.

Bow, Lateral – Deviation from straight of a longitudinal edge.

Bow, Longitudinal – Curvature in the plane of sheetor plate in the rolling direction.

Bow, Transverse – Curvature across the rolling direc-tion of sheet or plate.

Brazing – Joining metals by fusion of nonferrousalloys that have melting points above 425C (800F) butlower than those of the metals being joined. This maybe accomplished by means of a torch (torch brazing),in a furnace (furnace brazing), or by dipping in amolten flux bath (dip or flux brazing).

Brazing Rod – A rolled, extruded, or cast round fillermetal for use in joining by brazing.

Brazing Sheet – Sheet of a brazing alloy, or sheetclad with a brazing alloy on one or both sides.

Brazing Wire – Wire for use as a filler metal in joiningby brazing.

Bright Sheet – See “Sheet, (1SBMF), (S1SBF) and(S2SBF).”

Bristle Mark – See “Mark, Bristle.”

Broken Die – A deviation from the desired cross section due to the absence of a certain portion of thedie used to extrude the profile (shape).

Broken Edge – See “Edge, Broken.”

Broken Matte Finish – Non-uniform surface on theinside of packed rolled foil (Bright Spots).

Broken Surface – See “Crazing.”

Bruise – See “Mark, Roll Bruise.”

Buckle – A distortion of the surface of the metal.

Buckle, Arbor – Bend, crease, wrinkle, or departurefrom flat, occurring perpendicular to the slit edge of a

coil and which are repetitive in nature, with severitydecreasing as the distance increase in the coil fromthe original source. Normally, it is found on the ID of acoil but can appear on the coil OD as a result of a priorwinding operation.

Buckle, Center – Undulation (wavy region) in the center of the metal.

Buckle, Edge – Undulation (wavy region) along theedge(s) of the metal.

Buckle, Oil Can – See “Buckle, Trapped.”

Buckle, Quarter – Undulation (wavy region) whichoccur approximately at both quarter points across thewidth.

Buckle, Trapped – Undulation (wavy region) which issmaller sized and often circular in shape.

Buff Streak – See “Streak.”

Buffing – A mechanical finishing operation in whichfine abrasives are applied to a metal surface by rotating fabric wheels for the purpose of developing alustrous finish.

Burnish Streak – See, “Streak, Burnish.”

Burnishing – See “Two-Tone.”

Burr – A thin ridge of roughness left by a cutting operation such as slitting, trimming, shearing, blanking or sawing.

Bursting Strength – The pressure required to rupturea foil specimen when it is tested in a Mullen instrument under specified conditions. See also“Mullen Test.”

Bus Bar – A rigid electric conductor in the form of abar.

Butt-Seam Tube – See “Tube, Open-Seam.”

Camber – See “Bow, Lateral.”

Carbon Mark – See “Mark, Carbon.”

Center – The difference in thickness between themiddle and edges (average) of a sheet.

Center Buckle – See “Buckle.”

Chafing – See “Mark, Traffic.”

Chatter Mark –See “ Mark, Chatter.”

Chip Mark – See “Dent, Repeating.”

Chop – Metal sheared from a vertical surface of a dieforging, which is spread by the die over an adjoininghorizontal surface.

Chucking Lub – A lug or boss added to a forging sothat “on center” machining and forming may be performed with one setup or checking. This lug isfinally machined or cut away.



[email protected]

(562) 802-2721

Cinching – See “Scratch, Tension.”

Circle – A circular blank fabricated from plate, sheetor foil.

Clad Sheet – See “Sheet, Clad.”

Coating – Continuous film on the surface of a product.

Coating Blister – See “Blister, Coating.”

Coating Build-Up – A coating thickness greater thannominal in localized area of sheet, usually alongedges, due to uneven application techniques.

Coating Drip – A non-uniform extraneous deposit ofcoating on the coated sheet.

Coating Oven Trash – See “Dirt.”

Coating Streak – See “Streak, Coating.'

Coating, Conversion – An inorganic pretreatmentsometimes applied to metal surface to enhance coating adhesion and to retard corrosion.

Coating, High or Low – Failure of the coating tomeet the agreed upon thickness limits measured inweight per unit area.

Cobble – (1) A jamming of the mill by aluminum product while being rolled. (2) A piece of aluminumwhich for any reason has become so bent or twistedthat it must be withdrawn from the rolling operationsand scrapped.

Coil Curvature – See “Coil Set.”

Coil Orientation – Clockwise Coil: With the coil corevertical (“eye to the sky”) and viewed from above, atrace of the metal edge from the ID to the ODinvolves clockwise movement. Counter-Clockwise(Anti-Clockwise) Coil: With the coil core vertical (“eyeto the sky”) and viewed from above, a trace of themetal edge from the ID to the OD involves counter-clockwise (anti-clockwise) movement.

Coil Set – Longitudinal bow in an unwound coil in thesame direction as curvature of the wound coil.

Coil Set Differential – The difference in coil set fromthe edge to edge of a coiled sheet sample. It is measured with the sample on a flat table, concaveside up, and is the difference in elevation of the corners on one end.

Coil Set, Reversed – Longitudinal bow in anunwound coil in the direction opposite to the curvature of the wound coil.

Coiled Sheet – See “Sheet, Coiled.”

Cold Shut – (1) A Linear discontinuity in a cast surface caused when meeting streams of metal fail tomerge prior to solidification. (2) A forging defectdeveloped by metal flowing into a section from twodirections, resulting in a discontinuity at the junction.

Cold Working – Plastic (i.e., permanent) deformation of metal at such temperature and ratethat strain-hardening occurs.

Collapse – Out-of-round condition of coil often dueto inappropriate tension during rewinding operations.

Coloring – A finishing process or combination ofprocesses, which alters the appearance of an aluminum surface via coating, chemical and/ormechanical operations.

Concavity – Curved like the inner surface of asphere. See also “Convexity.”

Concentricity – Conformance to a common centeras, for example, the inner and outer walls of roundtube.

Condensation Stain – See “Corrosion, Water Stain.”

Condenser Tube – The term “Heat-Exchanger Tube”is preferred, unless specific reference to a condenserapplication is intended.

Conduit – A tube used to protect electric wiring. Seealso “Tubing, Electrical Metallic.”

Conduit, Rigid – Conduit having dimensions of ANSISchedule 40 pipe in standardized length with threaded ends.

Coned-out Coil – See “Telescoping.”

Contour – That portion of the outline of a transversecross section of an extruded shape that is represented by a curved line or curved lines.

Conversion Coating-Can Ends – See “Coating,Conversion.”

Convexity – Curved like the outer surface of asphere. See also “Concavity.”

Core – A hollow cylinder on which a coiled productmay be wound that forms the inside diameter of acoil.

Core Blister – See “Blister, Core.”

Coring – See “Back End Condition.”

Corner Turn-up – A distortion, buckle or twist condition that causes the corner(s) of the sheet todeviate from a perfectly flat plane on which it rests.

Corrosion – The deterioration of a metal or chemicalor electrochemical reaction with its environment.

Corrosion, Exfoliation – Corrosion that progressesapproximately parallel to the metal surface, causinglayers of the metal to be elevated by the formation ofcorrosion product.

Corrosion, Galvanic – Corrosion associated with thecurrent of galvanic cell consisting of two dissimilar conductors in an electrolyte or two similarconductors in dissimilar electrolytes. Aluminum willcorrode if it is anodic to the dissimilar metal.

Corrosion, Intergranular – Corrosion occurring preferentially at grain boundaries (also termed intercrystalline corrosion).




(562) 802-2721

Corrosion, Pitting – Localized corrosion resulting insmall pits or craters in a metal surface.

Corrosion, Stress Cracking – Failure by crackingresulting from selective directional attack caused bythe simultaneous interaction of sustained tensilestress at an exposed surface with the chemical orelectro-chemical effects of the surface environment.The term is often abbreviated SCC which correctlystands for stress corrosion cracking.

Corrosion, Water Stain – Superficial oxidation of thesurface with a water film, in the absence of circulating air, held between closely adjacent metalsurfaces.

Corrugating – Forming rolled metal into a series ofstraight parallel regular alternate grooves and ridges.

Coupon – A piece of metal from which a test specimen may be prepared.

Covering Area – Yield expressed in terms of a givennumber of square inches in a pound. For metric units,use square meters per kilogram.

Crazing – A macroscopic effect of numerous surface tears, transverse to the rolling direction,which can occur when the entry angle into the coldmill work rolls is large.

Crease – A sharp deviation from flat in the sheetwhich is transferred from processing equipment subsequent to the roll bite.

Cross Hatching – See “Crazing.”

Crown – See “Convexity.”

Curl – An undesirable condition caused by unevenrates of absorption or evaporation of moisture,uneven rates of contraction or expansion, or internalstresses in the material. Curl is most prevalent in laminated structures where the components have differing physical properties.

Deep Drawing – Forming a deeply recessed part byforcing sheet metal to undergo plastic flow betweendies, usually without substantial thinning of the sheet.

Defect – A defect is anything that renders the aluminum unfit for the specific use for which it wasordered.

Dent – (1) For rolled products, a sharply defined surface impression on the metal which may becaused by a blow from another object. (2) For extrusions, a synonym for handling mark. See “Mark,Handling.”

Dent, Expansion – Localized surface deviation fromflat generated by expansion of vapor during thermaltreatment of cold rolled coiled sheet.

Dent, Repeating – Repeating depression caused bya particle adhering to a rotating roll over which themetal has passed.

Die Line – A longitudinal depression or protrusionformed on the surface of drawn or extruded material. Die lines are present to some degree in allextrusions and are caused by a roughening of the diebearing.

Die Number – The number assigned to a die foridentification and cataloging purposes, and whichusually is assigned for the same purpose to the product produced from that die.

Diffusion Streak – See “Streak, Diffusion.

Dirt – Foreign debris from rolling or post-rolling operations imbedded in or under the coating.

Disc – A circular blank fabricated from plate, sheet orfoil, from which a central concentric area has beenremoved.

Double Shear Notch – See “Notch, Double Shear.”

Draft – Taper on the sides of a die or mold impression to facilitate removal of forgings, castingsor patterns from dies or molds.

Drag Mark – See “Rub, Tool.”

“Draw and Iron” - Can Bodies – Term which refersto a method of fabricating a can body in which a cupis drawn from flat sheet, redrawn to the final diameter and then wall ironed to reduce the wallthickness and to achieve the required height.

Drawing – (1) In forging, an operation of workingmetal between flat dies to reduce the cross sectionand increase length. (2) The process of pulling material through a die to reduce the size, change thecross section or shape, or harden the material.

Drawing Stock – A hot worked intermediate solidproduct of uniform cross section along its wholelength, supplied in coils and of a quality suitable fordrawing into wire.

Drawn Product – A product formed by pulling material through a die.

Drawn-in Scratch – See “Scratch, Drawn-in.”

Dropped Edge – See “Edge, Dropped.

Dry Sheet – See “Lube, Low.”

Dry Surface – A foil surface substantially free fromoily film, and suitable for lacquering, printing, or coating with water-dispersed adhesives.

Duct Sheet – Coiled or flat sheet in specific tempers, widths and thicknesses, suitable for ductapplications.

Ductility – The property that permits permanentdeformation before fracture by stress in tension.

Earing – Wavy symmetrical projections formed during cupping, deep drawing or spinning. Earing iscaused by nonuniform directional properties in thealuminum and/or by improperly adjusted tooling.



[email protected]

(562) 802-2721

Ears – Wavy symmetrical projections formed in thecourse of deep drawing or spinning as a result ofdirectional properties or anisotropy in sheet. Earsoccur in groups of 4 or 8 with the peaks of the projections located at 45 degrees and/or 0 and 90degrees to the rolling direction. Degree of earing isthe difference between average height at the peaksand average height at the valleys, divided by average height at the valleys, multiplied by 100 andexpressed in percent.

Eccentricity – Deviation from a common center, as,for example, the inner and outer walls of a roundtube. The difference between the mean wall thickness and minimum or maximum wall thicknessat any one cross section. The permissible degree ofeccentricity can be expressed by a plus and minuswall-thickness tolerance.

Edge, Band – See “Two-Tone.”

Edge, Belled – Excessive buildup of material onedge(s) during a rewinding operation. Typical causesinclude excessive edge burr, turned edge, and “dogbone” shaped cross sectional profiles.

Edge, Broken (Cracked) – Edge(s) containing crack,split, and/or tear which is caused by inability todeform without fracturing.

Edge, Buildup – See “Edge, Belled.”

Edge, Damaged – Edge of a coil that has been bent,torn or scraped by an object.

Edge, Dropped – A continuous, downward edgedeflection.

Edge, Liquated – Surface condition remaining afterportions of a side of an as-cast rolling ingot deformsenough during hot rolling to become top and/or bottom surface(s) of the rolled product at an edge.

Edge, Ripped – See “Buckled, Edge.”

Edge, Wavy – See “Buckle, Edge.”

Electrical Conductivity — The capacity of a material to conduct electric current. For aluminum,this capacity is expressed as a percentage of theInternational Annealed Copper Standard (IACS),which has a resistivity of 1/58 ohm-mm2/meter at 68degrees F and an arbitrarily designated conductivityof unity.

Electrical Resistivity – The electrical resistance of abody of unit length and unit cross-sectional area orunit weight. The value of 1/58 ohm-mm2/meter at 68degrees F is the resistivity equivalent to theInternational Annealed Copper Standard for 100 percent conductivity. This means that a wire of 100percent conductivity, 1 meter in length and 1 squaremillimeter in cross-sectional area would have aresistance of 0.017241 ohms at 68 degrees F.

Elongation – The percentage increase in distancebetween two gauge marks that results from stressing the specimen in tension to fracture. Theoriginal gauge length is usually 2 inches for flat

specimens and round specimens whose diameter is1/2 inch, or four times the diameter for specimenswhere that dimension is under 1/2 inch. Elongationvalues depend to some extent upon size and form ofthe test specimen. For example, the values obtainedfrom sheet specimens will be lower for thin sheetthan for thicker sheet.

Embossing – Raising a design in relief against a surface.

Endurance Limit – The limiting stress below which amaterial will withstand a specified large number ofcycles of stress.

Equivalent Round – The diameter of a circle havinga circumference equal to the outside perimeter ofother than round tube.

Extrusion – A product formed by pushing materialthrough a die.

Extrusion Billet – The starting stock for the extrusion operation. Extrusion billet is a solid or hollow form, commonly cylindrical and is the lengthcharged into the extrusion press cylinder. It is usually a cast product but may be a wrought product or powder compact.

Extrusion Butt End Defect – A longitudinal discontinuity in the extreme rear portion of an extruded product, which is normally discarded.

Extrusion Ingot – A cast form that is solid or hollow,usually cylindrical, suitable for extruding. See also“Fabricating Ingot.”

Extrusion Log – The starting stock for extrusion billet. Extrusion log is usually produced in lengthsfrom which shorter extrusion billets are cut.

Extrusion Seam – A region in extruded hollow profiles observed after creating two streams of metaland rejoining them around the mandrel of a portholeor bridge die.

Eyehole – See “Holiday.”

Fabricating Ingot – A cast form suitable for subsequent working by such methods as rolling,forging, extruding, etc. (“Rolling Ingot,” “ForgingIngot,” “Extrusion Ingot.”)

Fatigue – The tendency for a metal to break underconditions of repeated cyclic stressing considerablybelow the ultimate tensile strength.

Feed In – See “Back End Condition.”

Feed Line – See “Streak, Grinding.”

Fillet – A concave junction between two surfaces.

Fin – A thin projection on a forging resulting fromtrimming or from the metal under pressure beingforced into hairline cracks in the die or around dieinserts.




(562) 802-2721

Fin Stock – Coiled sheet or foil in specific alloys,tempers, and thickness ranges suitable for manufacture of fins for heat-exchanger applications.

Finish – The characteristics of the surface of a product.

Fish Mouthing – See “Lamination.”

Flag – A marker inserted adjacent to the edge at asplice or lap in a roll or foil.

Flaking – A condition in coated sheet where portions of the coating become loosened due toinadequate adhesion.

Flange – See “Rib.”

Flash – A thin protrusion at the parting line of a forging which forms when metal, in excess of thatrequired to fill the impressions, is forced between thedie interfaces.

Flash Line – A line left on a forging where flash hasbeen removed.

Flatness – (1) For rolled products, a distortion of thesurface of sheet such as a bulge or a wave, usuallytransverse to the direction of rolling. Often describedby location across width, i.e., edge buckle, quarterbuckle, center, buckle, etc. (2) For extrusions, flatness (off contour) pertains to the deviation of across-section surface intended to be flat. Flatnesscan be affected by conditions such as die performance, thermal effects and stretching.

Flow Lines – (1) Lines on the surface of paintedsheet, brought about by incomplete leveling of thepaint. (2) The line pattern revealed by etching, whichshows the direction of plastic flow on the surface orwithin a wrought structure.

Flow Through – A forging defect caused when metalflows past the base of a rib resulting in rupture of thegrain structure.

Foil – A rolled product rectangular in cross section ofthickness less than 0.006 inch. In Europe, foil is equalto and less than 0.20 mm.

Foil Stock – See “Reroll Stock.”

Foil, Annealed – Foil completely softened by thermaltreatment.

Foil, Bright Two Sides – Foil having a uniform brightspecular finish on both sides.

Foil, Chemically Cleaned – Foil chemically washedto remove lubricant and foreign material.

Foil, Embossed – Foil on which a pattern has beenimpressed by means of an engraved roll or plate.

Foil, Etched – Foil roughened chemically or electrochemically to provide an increased surfacearea.

Foil, Hard – Foil fully work-hardened by rolling.

Foil, Intermediate Temper – Foil intermediate in temper between Annealed Foil and Hard Foil.

Foil, Matte One Side (MIS) – Foil with a diffusereflecting finish on one side and a bright specular finish on the other.

Foil, Mechanically Grained – Foil mechanicallyroughened for such applications as lithography.

Foil, Mill Finish (MF) – Foil having a non-uniform finish which may vary from coil to coil and within acoil.

Foil, Scratch Brushed – Foil abraded, usually withwire brushes, to produce a roughened surface.

Fold – A forging discontinuity caused by metal folding back on its own surface during flow in the diecavity.

Forgeability – The term used to describe the relativeworkability of forging material.

Forging – A metal part worked to a predeterminedshape by one or more processes such as hammering, upsetting, pressing, rolling. etc.

Forging Billet – The term “Forging Stock” is preferred.

Forging Ingot – A cast form intended and suitable forsubsequent working by the forging process.

Forging Plane – A reference plane or planes normalto the direction of applied force from which all draftangles are measured.

Forging Stock – A wrought or cast rod, bar or othersection suitable for forging.

Forging, Blocker-Type – A forging made in a singleset of impressions to the general contour of a finished part.

Forging, Cold-Coined – A forging that has beenrestruck cold in order to obtain closer dimensions, tosharpen corners or outlines and in non-heat-treatablealloys, to increase hardness.

Forging, Die – A forging formed to the required shapeand size by working in impression dies.

Forging, Draftless – A forging with zero draft on vertical walls.

Forging, Flashless – A closed die forging made indies constructed and operated to eliminate, in predetermined areas, the formation of flash.

Forging, Hammer – A forging produced by repeatedblows in a forging hammer.

Forging, Hand – A forging worked between flat orsimply shaped dies by repeated strokes or blows andmanipulation of the piece.

Forging, No-Draft – See “Forging, Draftless.”

Forging, Precision – A forging produced to tolaerances closer than standard.



[email protected]

(562) 802-2721

Forging, Press – A die forging produced by pressureapplied in a forging press.

Forging, Rolled Ring – A cylindrical product of relatively short height, circumferentially rolled from ahollow section.

Forging, Upset – A forging having part or all of itscross section greater than that of the stock.

Formability – The relative ease with which a metalcan be shaped through plastic deformation.

Fracture Toughness – A generic term for measure ofresistance to extension of a crack. The term is sometimes restricted to results of a fracture mechanics test, which is directly applicable in fracture control.

Fretting – See “Mark, Traffic.”

Friction Scratch – See “Scratch, Friction.”

Full Center – See “Buckle, Center.”

Gauge – A term previously used in referring to thethickness of a wrought product. Thickness is preferred in dimension description.

Glaze – See “Pickup, Roll.”

Gouge – A gross scratch. See “Scratch.”

Gouge, Rolled In – A more localized gross rolled-inscratch. See also “Scratch, Rolled-in.”

Grain Flow – The directional characteristics of themetal structure after working, revealed by etching apolished section.

Grain Size – A measure of crystal size usually reported in terms of average diameter in millimeters,grains per square millimeter, or grains per cubic millimeter.

Grease Streak – See “Streak, Grease.”

Hair, Slitter – Minute hair-like sliver along edge(s)due to shearing or slitting operation.

Handling Mark – See “Mark, Handling.”

Hardener – An alloy containing at least some aluminum and one or more added elements for use inmaking alloying additions to molten aluminum. Alsoreferred to as “Master Alloy.”

Hardness – Resistance to plastic deformation, usually by indentation. The term may also refer tostiffness or temper, or to resistance to scratching,abrasion or cutting. Brinell Hardness: Brinell hardness of aluminum alloys is obtained by measuring the permanent impression in the materialmade by a ball indenter 10 millimeters in diameterafter loading with a 500 kilogram-force for 15 seconds and dividing the applied load by the area ofthe impression. Rockwell Hardness: An indentationhardness test based on the depth of penetration of aspecified penetrator into the specimen under

certain arbitrarily fixed conditions.

Heat Streak – See “Streak, Heat.”

Heat Treat Lot – See “Lot, Heat Treat.”

Heat Treat Stain – A discoloration due to non-uniform oxidation of the metal surface duringsolution heat treatment.

Heat Treating – Heating and cooling a solid metal oralloy in such a way as to obtain desired conditions orproperties. Commonly used as a shop term to denotea thermal treatment to increase strength. Heating forthe sole purpose of hot working is excluded from themeaning of this definition – see “Solution HeatTreating,” Aging.”

Heat-Treatable Alloy – An alloy which may bestrengthened by a suitable thermal treatment.

Herringbone – See “Streak, Herringbone.”

Hole – Void in rolled product. Typical cause is a non-metallic inclusion during rolling.

Holiday – Region where film is absent due to non-wetting of the metal surface by the coating.

Homogenizing – Is a process whereby ingots areraised to temperatures near the solidus temperatureand held at that temperature for varying lengths oftime. The purposes of this process are to (1) reducemicrosegregation by promoting diffusion of soluteatoms within the grains of aluminum and (2) improveworkability.

Hook – An abrupt deviation from straightness. Hookcan be caused by non-uniform metal flow duringbreakthrough. See also “Bow.”

Hot Line Pickup – See “Pickup, Roll.”

Hot Shortness – A condition of the metal at excessively high working temperatures characterized by low mechanical strength and a tendency for the metal to crack rather than deform.

Hot Spot – Dark grey or black surface patchesappearing after anodizing. These areas are usuallyassociated with lower hardness and coarse magnesium silicide precipitate caused by non-uniform cooling after extrusion.

Hot Tear – See “Tear, Speed.”

Hot Working – Plastic deformation of metal at suchtemperature and rate that strain hardening does notoccur.

Impact – A part formed in a confining die from ametal slug, usually cold, by rapid single stroke application of force through a punch, causing themetal to flow around the punch and/or through anopening in the punch or die.

Inclusion – Foreign material in the metal orimpressed into the surface.




(562) 802-2721

Inclusion, Stringer – An impurity, metallic or non-metallic, which is trapped in the ingot and elongated subsequently in the direction of working. Itmay be revealed during working or finishing as a nar-row streak parallel to the direction of working.

Incomplete Seam – See “Weld, Incomplete.”

Ingot – A cast form suitable for remelting or fabricating. See “Remelt Ingot,” “Fabricating Ingot, ““Extrusion Ingot,” “Forging Ingot,” “Rolling Ingot.”

Inspection Lot – See “Lot, Inspection.”

Interleaving – The insertion of paper or applicationof suitable strippable coatings between layers ofmetal to protect from damage.

Kink – (1) For rolled products, an abrupt bend ordeviation from flat which is caused by localizedbending during handling. (2) For extrusions, anabrupt deviation from straightness. A kink can becaused by handling.

Knife Mark – See “Mark, Knife.”

Knock-Out Mark – See “Mark, Knock-Out.”

Lacquer – Occasionally used to describe oil stain.See “Stain, Oil.”

Lamination – An internal crack or separation alignedparallel to the direction of major metal flow and, in thecase of plate, sheet or foil, parallel to the rolled surfaces. In extrusions, it can be caused by contaminants that feed into the metal flow before itreaches the die opening or cracked billets. See also“Back End Condition.”

Lap – See “Fold.”

Lateral Bow – See “Bow, Lateral.”

Layout Sample – A prototype forging or a “cast”used to determine conformance to designed dimensions.

Leveling – The mechanical flattening of plate, sheetor foil.

Leveling, Roller – Leveling carried out by bending.

Leveling, Stretcher – Leveling carried out by uniaxial tension.

Leveling, Tension – Leveling continuously carriedout by uniaxial stretching usually with the assistanceof bending.

Leveling, Thermal – Leveling carried out at an elevated temperature under an applied load normalto the surface to be flattened.

Leveller Chatter – See “Mark, Chatter (Roll orLeveller).”

Leveller, Mark – See “Dent, Repeating.”

Leveller Streak – See “Streak, Leveller.”

Line, Flow – The line pattern which shows the direction of flow on the surface.

Line, Looper – Closely spaced symmetrical lines onthe surface of metal which has undergone non-uniform deformation, usually in a drawing operation.

Line, Luders – Elongated surface marking or depres-sions appearing in patterns caused by localized plastic deformation that results from non-uniform yielding.

Line, Weld – See “Seam, Extrusion.”

Liner – The slab of coating metal that is placed onthe core alloy and is subsequently rolled down toclad sheet as composite.

Liquated Edge – See “Edge, Liquated.”

Liquation – The bleeding of the low-melting constituents through the solidified ingot surface.

Lock – A condition in which the parting line of a forging is not all in one plane.

Log – See “Extrusion Log.”

Long Transverse Direction – For plate, sheet andforgings, the direction perpendicular to the longitudinal direction which is also at right angles tothe thickness of the product. See also “LongitudinalDirection.”

Longitudinal Bow – See “Bow, Longitudinal.”

Longitudinal Direction – The direction of majormetal flow in a working operation.

Looper Line – See “Line, Looper.”

Loose Wrap – See “Wrap, Loose.”

Lot, Heat Treat – Material of the same mill form,alloy, temper, section and size traceable to one heat-treat furnace load (or extrusion charge or billetin the case of press heat-treated extrusions) or, ifheat treated in a continuous furnace, charged consecutively during an 8-hour period.

Lot, Inspection – (1) For non-heat treated tempers,an identifiable quantity of material of the same millform, alloy, temper, section and size submitted forinspection at one time. (2) For heat treated tempers,an identifiable quantity of material of the same millform, alloy, temper, section and size traceable to aheat treat lot or lots and submitted for inspection atone time. (For sheet and plate, all material of thesame thickness is considered to be of the same size.)

Lube, High – Lubricant limit exceeds the maximumagreed upon limit measured in weight per unit area.

Lube, Low – Failure of the lubricant to meet theagreed upon minimum limit measured in weight perunit area.

Luders Line – See “Liner, Luders.”



[email protected]

(562) 802-2721

Mark – Damage in the surface of the product whosename is often described by source.

Mark, Arbor – Surface damage in the vicinity of a coilID caused by contact with a roughened, damaged or non-circular arbor.

Mark, Bearing – A depression in the extruded surface caused by a change in bearing length in theextrusion die.

Mark, Bite – A line which is generally perpendicularto the rolling direction.

Mark, Bristle – Raised surface about one inch long,crimped wire shaped and oriented in any direction.

Mark, Carbon – Gray or black surface markingcaused by contact with carbon runout blocks.

Mark, Chatter (Roll or Leveller) — Numerous intermittent lines or grooves that are usually full widthand perpendicular to the rolling or extrusion direction.

Mark, Drag – See “Rub, Tool.”

Mark, Edge Follower – Faint intermittent marks atthe edge of a cold rolled product which are usuallyperpendicular to the rolling direction. This mark iscaused by action of devices designed to rewind coilswithout weave.

Mark, Handling – (1) For rolled products, an area ofbroken surface that is introduced after processing.The mark usually has no relationship to the rollingdirection. (2) For extrusions, damage that can beimparted to the surface during handling operations.

Mark, Heat Treat Contact – Brownish, iridescent,irregularly shaped stain with a slight abrasion located somewhere within the boundary of the stain.It is a result of metal-to-metal contact during thequenching of solution heat-treated flat sheet or plate.

Mark, Inclusion – Appearance of surface where actual inclusion or the void it left is observed. See also“Inclusion, Stringer.”

Mark, Knife – A continuous scratch (which may alsobe creased) near a slit edge, caused by sheet contacting the slitter knife.

Mark, Knock-Out – A small solid protrusion or circular fin on a forging or a casting, resulting from thedepression of a knock-out pin under pressure orinflow of metal between the knock-out pin and the dieor mold.

Mark, Leveller Chatter – See “Mark, Chatter (Roll orLeveller).”

Mark, Metal-on-Roll – See “Dent, Repeating.”

Mark, Mike – Narrow continuous line near the rollededge caused by a contacting micrometer.

Mark, Pinch – See “Crease.”

Mark, Roll – (1) For rolled products, a small repeatingraised or depressed area caused by the opposite condition on a roll. The repeat distance is a function ofthe offending roll diameter. (2) For extrusions, a longitudinal groove or indentation caused by pressurefrom contour rolls as a profile (shape) passes throughthem for dimensional correction.

Mark, Roll Bruise – A greatly enlarged roll, markwhose height or depth is very shallow. See also“Mark, Roll.”

Mark, Roll Skid – A full width line perpendicular to therolling direction and repeating as a function of a workroll diameter.

Mark, Rub – A large number of very fine scratches orabrasions. A rub mark can occur by metal-to-metalcontact, movement in handling and movement intransit.

Mark, Snap – A band-like pattern around the fullperimeter of an extruded section and perpendicular toits length. A snap mark can occur whenever there isan abrupt change in the extrusion process. See also“Mark, Stop.”

Mark, Stop – A band-like pattern around the fullperimeter of an extruded section and perpendicular toits length. A stop mark occurs whenever the extrusion process is suspended. See also “Mark,Snap.”

Mark, Stretcher Jaw – A cross hatched appearanceleft by jaws at the end(s) of metal that has beenstretched. These marks are seen if insufficient metalhas been removed after the stretching operation.

Mark, Tab – See “Buckle, Arbor.”

Mark, Tail – See “Mark, Roll Bruise.”

Mark, Take Up – See “Scratch, Tension.”

Mark, Traffic – Abrasion which results from relativemovement between contacting metal surfaces during handling and transit. A dark color from the abrasively produced aluminum oxide is usuallyobserved. A mirror image of a traffic mark is observedon the adjacent contacting surface.

Mark, Whip – A surface abrasion which is generallydiagonal to the rolling direction. It is caused by a fluttering action of the metal as it enters the rollingmill.

Master Alloy – See “Hardener.”

Mean Diameter – The average of two measurementsof the diameter at right angles to each other.

Mechanical Properties – Those properties of a material that are associated with elastic and inelastic reaction when force is applied, or that involvethe relationship between stress and strain; for example, modulus of elasticity, tensile strength,endurance limit. These properties are often incorrectlyreferred to as physical properties.




(562) 802-2721

Mike Mark – Narrow continuous line near the rollededge caused by a contacting micrometer.

Minimum Residual Stress (MRS) –The term appliedto products, usually flat rolled, which have beenprocessed to minimize internal stress of the kind thatcauses distortion when material is disproportionatelyremoved from one of the two surfaces throughmechanical or chemical means.

Mismatch – Error in register between two halves of aforging by opposing die halves not being in perfectalignment.

Modulus of Elasticity – The ratio of stress to corresponding strain throughout the range where theyare proportional. As there are three kinds of stresses,so there are three kinds of moduli of elasticity for anymaterial – modulus in tension, in compression, and inshear.

Mottling, Pressure – Non-uniform surface appearance resulting from uneven pressure distribution between adjacent layers of the product.

Mullen Test – Measurement of bursting strength offoil in pounds per square inch. Testing machineapplies increasing pressure to one square inch of thesample until it ruptures.

Natural Aging – See “Aging.”

Nick – Rolled products, see “Scratch.” Extrusions,see “Mark, Handling.”

Non-Heat-Treatable Alloy – An alloy which can bestrengthened only by cold work.

Nonfill – Failure of metal to fill a forging die impression.

Notch, Double Shear – An abrupt deviation fromstraight on a sheared edge. This offset may occur ifthe flat sheet or plate product is longer than the bladefor the final shearing operation.

Off Gauge – Deviation of thickness or diameter of asolid product, or wall thickness of a tubular product,from the standard or specified dimensional tolerances.

Offset – Yield strength by the “offset method” iscomputed from a load-strain curve obtained bymeans of an extensometer. A straight line is drawnparallel to the initial straight line portion of the load-strain curve and at a distance to the right corresponding to 0.2 percent offset (0.002 in. per in.of gauge length). The load reached at the point wherethis straight line intersects the curve divided by theoriginal cross-sectional area (sq. in.) of the tensiontest specimen is the yield strength.

Oil Stain – See “Stain, Oil.”

Orange Peel - Surface roughening on formed products which occurs when large grains in the metalare present.

Oscillation – Uneven wrap in coiling and lateral travel during winding. Improper alignment of rollsover which the metal passes before rewinding andinsufficient rewind tension are typical causes. Seealso “Telescoping.”

Out-of-Register – An embossed pattern distortiondue to misalignment of the male and female embossing rolls.

Ovality – Deviation from a circular periphery, usuallyexpress as the total difference found at any one crosssection between the individual maximum and minimum diameters, which usually occur at or about90 degrees to each other. Since ovality is the difference between extreme diameters, it is not theexpressed as plus of minus.

Ovalness – See “Ovality.”

Oxide Discoloration – See “Stain, Heat Treat.”

Pack Rolling – The simultaneous rolling of two ormore thicknesses of foil.

Parent Coil – A coil that has been processed to finaltemper as a single unit. The parent coil may subsequently be cut into two or more smaller coils orinto individual sheets or plates to provide therequired width and length.

Parent Plate – A plate that has been processed tofinal temper as a single unit. The parent plate maysubsequently be cut into two or more smaller platesto provide the required width and length.

Partial Annealing – See “Annealing, Partial.”

Parting Line – A condition unique to stepped extrusions where more than one cross section existsin the same extruded shape. A stepped shape uses asplit die for the minor or small cross section and afterits removal, another die behind it for the major configuration. Slightly raised fins can appear on thatportion of the shape where the two dies meet. Seealso “Profile, Stepped Extruded.”

Patterned Sheet – See “Embossing.”

Physical Properties – The properties, other thanmechanical properties, that pertain to the physics ofa material; for example, density, electrical conductivity, heat conductivity, thermal expansion.

Pick-Off – The transfer of portions of the coatingfrom one surface of the sheet to an adjacent surfacedue to poor adhesion of the coating.

Pickup – Small particles of oxide adhering to the surface of a product at irregular intervals.

Pickup, Repeating – See “Dent, Repeating.”



[email protected]

(562) 802-2721

Pickup, Roll – Small particles of aluminum and aluminum oxide generated in the roll bite which subsequently transfer to the rolled product. It may bedistributed uniformly and/or in streaks. See also“Streak, Coating.”

Pinch Mark – See “Crease.”

Pinhole – (1) Minute hole in foil. (2) A small-sized voidin the coating of a sheet or foil product. A typical cause is solvent popping.

Pipe – Tube in standardized combinations of outsidediameter and wall thickness, commonly designatedby “Nominal Pipe Sizes” and “ANSI ScheduleNumbers.”

Pipe, Drawn – Pipe brought to the final dimensionsby drawing through a die.

Pipe, Extruded – Pipe formed by hot extruding.

Pipe, Seamless – Extruded or drawn pipe whichdoes not contain any line junctures resulting from themethod of manufacture.

Pipe, Structural – Pipe commonly used for structural purposes.

Piping – See “Back End Condition.”

Pit – A depression in the rolled surface which is usually not visible from opposite side.

Pitting – See “Corrosion.”

Plate – A rolled product that is rectangular in crosssection and with thickness not less than 0.250 inchwith sheared or sawed edges.

Plate Circle – Circle cut from plate.

Plate, Alclad – Composite plate comprised of an aluminum alloy core having on both surfaces (if onone side only, Alclad One Side Plate) a metallurgicallybonded aluminum or aluminum alloy coating that isanodic to the core, thus electrolytically protecting thecore against corrosion.

Pop, Solvent – Blister and/or void in the coatingresulting from trapped solvents released during curing process.

Precipitation Hardening – See “Aging.”

Precipitation Heat Treating – See “Aging.”

Preheating –A high temperature soaking treatmentto provide a desired metallurgical structure.Homogenizing is a form of preheating.

Pressure Mottling – See “Mottling, Pressure.”

Profile – A wrought product that is long in relation toits cross-sectional dimensions which is of a formother than that of sheet, plate, rod, bar, tube, wire orfoil.

Profile, Class 1 Hollow Extruded – A hollow extruded profile, the void of which is round and 1 inch

or more in diameter and whose weight is equally distributed on opposite sides of two or moreequally spaced axes.

Profile, Class 2 Hollow Extruded – Any hollowextruded profile other than Class 1, which does notexceed a 5-inch diameter circumscribing circle andhas a single void of not less than 0.375-inch diameter or 0.110-square inch area.

Profile, Class 3 Hollow Extruded – Any hollowextruded profile other than Class 1 or Class 2.

Profile, Cold-Finished – A profile brought to finaldimensions by cold-working to obtain improved surface finish and dimensional tolerances.

Profile, Cold-Finished Extruded – A profile produced by cold-finishing an extruded profile.

Profile, Cold-Finished Rolled – A profile producedby cold-finishing a rolled profile.

Profile, Drawn – A profile brought to final dimensions by drawing through a die.

Profile, Extruded – A profile produced by hot extruding.

Profile, Flute Hollow – A hollow profile having plaininside surfaces and whose outside surfaces comprise regular, longitudinal, concave corrugationswith sharp cusps between corrugations.

Profile, Helical Extruded – An extruded profile twisted along its length.

Profile, Hollow – A profile any part of whose crosssection completely encloses a void.

Profile, Lip Hollow – A hollow profile of generally circular cross section and nominally uniform wallthickness with one hollow or solid protuberance or lipparallel to the longitudinal axis; used principally forheat-exchange purposes.

Profile, Pinion Hollow – A hollow profile with regularly spaced, longitudinal serrations outside andround inside, used primarily for making small gears.

Profile, Rolled – A profile produced by hot rolling.

Profile, Semihollow – A profile any part of whosecross section is a partially enclosed void the area ofwhich is substantially greater than the square of thewidth of the gap. The ratio of the area of the void tothe square of the gap is dependent of the class ofsemihollow profile, the alloy and the gap width.

Profile, Solid – A profile other than hollow or semihollow.

Profile, Stepped Extruded – An extruded profilewhose cross section changes abruptly in area at inter-vals along its length.

Profile, Streamline Hollow –A hollow profile with across section of tear-drop shape.




(562) 802-2721

Profile, Structural – A profile in certain standardalloys, tempers, sizes, and sections, such as angles,channels, H-sections, I-beams, tees, and zees commonly used for structural purposes. For channels and I-beams, there are two standards,namely Aluminum Association Standard andAmerican Standard.

Profile, Tapered Extruded – An extruded profilewhose cross section changes continuously in areaalong its length or a specified portion thereof.

Quarter Buckle – See “Buckle, Quarter.”

Quenching – Controlled rapid cooling of a metal froman elevated temperature by contact with a liquid, agas, or a solid.

RCS – Abbreviation for Rigid Container Sheet.

Razor Streak – See “Inclusion, Stringer.”

Rear End Condition – See “Back End Condition.”

Redraw Rod – This term is not recommended. Theterm “Drawing Stock” is preferred.

Refined Aluminum – Aluminum of very high purity(99.950 percent or higher) obtained by special metallurgical treatments.

Reflector Sheet – Sheet suitable for the manufactureof reflectors.

Reheating – Heating metal again to hot-workingtemperature. In general no structural changes areintended.

Reoil – Oil put on the sheet after cleaning and beforecoiling for shipment to prevent water stain.

Reroll Stock – A semi-finished rolled product of rectangular cross section in coiled form suitable forfurther rolling. Examples: “Foil Stock” and “SheetStock.”

Rib – An elongated projection on a shape, forging orcasting to provide stiffening.

Rivet - See “Wire, Cold Heating.”

Rod – A solid wrought product that is long in relationto its circular cross section, which is not less than0.375 inch diameter.

Rod, Alclad – Rod having on its surface a metallurgically bonded aluminum or aluminum alloycoating that is anodic to the core alloy to which it isbonded, thus electrolytically protecting the core alloyagainst corrosion.

Rod, Cold-Finished – Rod brought to final dimensions by cold working to obtain improved sur-face finish and dimensional tolerances.

Rod, Cold-Finished Extruded – Rod produced bycold working extruded rod.

Rod, Cold-Finished Rolled – Rod produced by coldworking rolled rod.

Rod, Cold-Heating – Rod of a quality suitable foruse in the manufacture of cold-headed productssuch as rivets and bolts.

Rod, Extruded – Rod produced by hot extruding.

Rod, Rivet – See “Rod, Cold Heating.”

Rod, Rolled – Rod produced by hot rolling.

Roll Chatter – See “Mark, Chatter (Roll or Leveller.)

Roll Coating – See “Streak, Coating.”

Roll Grind – The uniform ground finish on the workrolls which is imparted to the sheet or plate duringrolling.

Roll Mark – See “Mark, Roll.”

Roll Pickup – See “Pickup, Roll.”

Rolled Ring – See “Forging, Rolled Ring.”

Rolled-in Scratch – See “Scratch, Rolled-in.”

Rolled-in Metal – An extraneous chip or particle ofmetal rolled into the surface of the product.

Rolled-over Edge – See “Edge, Liquated.”

Rolling Ingot – A cast form suitable for rolling. See“Fabricating Ingot.”

Rolling Slab – A rectangular semifinished product,produced by hot rolling fabricating ingot and suitable for further rolling.

Roofing Sheet – Coiled or flat sheet in specific tempers, widths, and thicknesses suitable for themanufacture of corrugated or V-crimp roofing.

Roping – A rope-like appearance in the rolling direction after the metal has undergone sever deformation.

Roundness – This term is not recommended. Theterm “Ovality” is preferred.

Rub Mark – See “Mark, Rub.”

Rub, Tool – A surface area showing a scratch orabrasion resulting from contact of the hot extrusionwith the press equipment or tooling or, in the case ofmulti-hole dies, with other sections as they exit thepress.

Sample – A part, portion, or piece taken for purposes of inspection or test as representative ofthe whole.

Saw-Plate Bar – See “Bar, Saw-Plate.”

Scalping – Mechanical removal of the surface layerfrom a fabricating ingot or semi-finished wroughtproduct so that surface imperfections will not beworked into the finished product.



[email protected]

(562) 802-2721

Scratch – (1) For rolled products, a sharp indentation in the surface usually caused by amachine or during handling. (2) For extrusions, a synonym for handling mark. See “Mark, Handling.”

Scratch, Drawn-in – A scratch occurring during thefabricating process and subsequently drawn over,making it relatively smooth to the touch.

Scratch, Friction – A scratch caused by relativemotion between two contacting surfaces.

Scratch, Handling – A more severe form of rubmark. See “Mark, Rub.”

Scratch, Machine – An indentation which is straight,is in the rolling direction and is caused by contactwith a sharp projection on equipment.

Scratch, Oscillation – Minor indentations at an angleto the rolling direction that result from coil oscillationduring unwinding or rewinding.

Scratch, Oven – A scratch which is caused by moving contact of coating against a non-movingobject in an oven.

Scratch, Rolled-in – A scratch which is subsequently rolled. It will then appear as a greyishwhite ladder (distinct transverse lines within the longitudinal indentation).

Scratch, Slippage – See “Scratch, Tension.”

Scratch, Tension – A short longitudinal indentationparallel to the rolling direction.

Seam Defect – An unbonded fold or lap on the surface of the metal, which appears as a crack, usually the result of a defect in working that has notbonded shut.

Seam, Extrusion – The junction line of metal that haspassed through a hollow die, separated and rejoinedat the exit point. Seams are present in all extrudedhollows produced from the direct extrusion processand in many cases are not visible. See “Weld,Incomplete.”

Seamless – A hollow product which does not contain any line junctures resulting from method ofmanufacture.

Section Number – The number assigned to anextruded or drawn profile (shape) for identificationand cataloging purposes, usually the same numberassigned for the same purpose to the die from whichthe profile (shape) is made.

Serpentine Weave – See “Snaking.”

Shape – This terms is no longer recommended. Theterms “Profile” is preferred. See “Profile.”

Shear Strength – The maximum stress that a material is capable of sustaining in shear. In practice,shear strength is considered to be the maximumaverage stress computed by dividing the ultimateload in the plane of shear by the original area subject

to shear. Shear strength is usually determined byinserting a cylindrical specimen through round holesin three hardened steel blocks, the center of which ispulled (or pushed) between the other two so as toshear the specimen on two planes. The maximumload divided by the combined cross-sectional area ofthe two planes is the shear strength.

Sheet – A rolled product that is rectangular in crosssection with thickness less than 0.250 inch but notless than 0.006 inch and with slit, sheared or sawededges.

Sheet Stock – See “Reroll Stock.”

Sheet, Alclad – Composite sheet comprised of analuminum alloy core having on both surfaces (if oneside only, Alclad One Side Sheet ) a metallurgicallybonded aluminum or aluminum alloy coating that isanodic to the core, thus electrolytically protecting thecore against corrosion.

Sheet, Anodizing – Sheet with metallurgical characteristics and surface quality suitable for thedevelopment of protective and decorative films myanodic oxidation processes.

Sheet, Clad – Composite sheet having on both surfaces (if on one side only, Clad One Side Sheet ) ametallurgically bonded metal coating, the composition of which may or may not be the same asthat of the core.

Sheet, Coiled – Sheet in coils with slit edges.

Sheet Coiled Circles – Circles cut from coiled sheet.

Sheet, Coiled Cut to Length – Sheet cut to specified length from coils and which has a lesserdegree of flatness than flat sheet.

Sheet, Flat – Sheet with sheared, slit or sawededges, which has been flattened or leveled.

Sheet, Flat Circles – Circles cut from flat sheet.

Sheet, Mill Finish (MF) – Sheet having a non-uniformfinish that may vary from sheet to sheet and within asheet, and may not be entirely free from stains or oil.

Sheet, One Side Bright Mill Finish (1SBMF) – Sheethaving a moderate degree of brightness on one sideand a mill finish on the other.

Sheet, Painted – Sheet, one or both sides of whichhas a factory-applied paint coating of controlledthickness.

Sheet, Standard One Side Bright Finish (S1SBF) –Sheet having a uniform bright finish on one side anda mill finish on the other.

Sheet, Standard Two Sides Bright Finish (S2SBF) –Sheet having a uniform bright finish on both sides.

Short Transverse Direction – For plate, sheet andforgings, the direction through the thickness perpendicular to both longitudinal and long transverse directions.




(562) 802-2721

Shrinkage – Contraction that occurs when metalcools from the hot-working temperature.

Side Crack – See “Edge, Broken (Cracked).”

Side Set – A difference in thickness between the twoedges of plate, sheet or foil.

Skip – an area of uncoated sheet which is frequentlycaused by equipment malfunction.

Slippage Scratch – See “Scratch, Tension.”

Slitter Hair – See “Hair, Slitter.”

Sliver – Thin fragment of aluminum which is part ofthe material but only partially attached. Surface damage or residual liquation which is subsequentlyrolled are typical causes.

Slug – A metal blank for forging or impacting.

Smudge – A dark film of debris, sometimes coveringlarge areas, deposited on the sheet during rolling.

Smut – See “Smudge.”

Snaking – A series of reversing lateral bows in coilproducts. This condition is caused by a weavingaction during an unwinding or rewinding operation.

Solution Heat Treating – Heating an alloy at a suitable temperature for sufficient time to allow soluble constituents to enter into solid solution wherethey are retained in a supersaturated state afterquenching.

Specimen – That portion of a sample taken for evaluation of some specific characteristic or property.

Speed Crack – See “Tear, Speed.”

Speed Tear – See “Tear, Speed.”

Splice – The end joint uniting two webs.

Spot, Lube – A non-uniform extraneous deposit oflube on the coated sheet.

Squareness – Characteristics of having adjacentsides or planes meeting at 90 degrees.

Stabilizing – A low temperature thermal treatmentdesigned to prevent age-softening in certain strainhardened alloys containing magnesium.

Stain, Heat Treat – A discoloration due to non-uniform oxidation of the metal surface duringheat treatment.

Stain, Oil – Surface discoloration which may varyfrom dark brown to white and is produced duringthermal treatment by incomplete evaporation and/oroxidation of lubricants on the surface.

Stain, Saw Lubricant – A yellow to brown area ofsurface discoloration at the ends of the extrudedlength. It is the residue of certain types of saw lubricants if they are not removed from the metalprior to the thermal treatment.

Stain, Water – See “Corrosion, Water Stain.”

Starvation – Non-uniform coating application whichresults in absence of coating in certain areas.

Sticking – Adherence of foil surfaces sufficient tointerfere with the normal ease of unwinding.

Straightness – The absence of divergence from aright (straight) line in the direction of measurement.

Strain – A measure of the change in size or shape ofa body under stress, referred to its original size orshape. Tensile or compressive strain is the change,due to force, per unity of length in an original lineardimension in the direction of the force. It is usuallymeasured as the change (in inches) per inch oflength.

Strain Hardening – Modification of a metal structureby cold working resulting in an increase in strengthand hardness with loss of ductility.

Streak (Stripe) – A superficial band or elongatedmark which produces a non-uniform surface appearance. A streak is often described by source.

Streak, Bearing – A longitudinal discoloration thatcan occur where there are large changes in wallthickness as a result of uneven cooling. Thesestreaks usually appear lighter than the surroundingmetal.

Streak, Bright – A bright superficial band or elongated mark which produces a non-uniform surface appearance.

Streak, Buff – A dull continuous streak caused bysmudge buildup on a buff used at shearing or otheroperations.

Streak, Burnish – A bright region on the sheetcaused by excessive roll surface wear.

Streak, Coating – A banded condition caused bynon-uniform adherence of roll coating to a work roll.It can be created during hot and/or cold rolling. Ifgenerated in the hot rolling process, it is also called“Hot Mill Pickup.”

Streak, Cold – See “Streak, Heat.”

Streak, Diffusion – Surface discoloration which mayvary from gray to brown and found only on Alcladproducts.

Streak, Dirt – Surface discoloration which may varyfrom gray to black, is parallel to the direction ofrolling, and contains rolled in foreign debris. It is usually extraneous material from an overhead location that drops onto the rolling surface and isshallow enough to be removed by etching or buffing.

Streak, Grease – A narrow discontinuous streakcaused by rolling over an area containing grosslyexcessive lubricant drippage.

Streak, Grinding – A streak with a helical patternappearance transferred to a rolled product from awork roll.



[email protected]

(562) 802-2721

Streak, Heat – Milky colored band(s) parallel to therolling direction which vary in both width and exactlocation along the length.

Streak, Herringbone – Elongated alternately brightand dull chevron markings.

Streak, Leveller – A streak on the sheet surface inthe rolling direction caused by transfer from the leveller rolls.

Streak, Mill Buff – See “Streak, Roll.”

Streak, Pickup – See “Streak, Coating.”

Streak, Roll – A non-uniform surface appearanceparallel to the rolling direction.

Streak, Structural – A non-uniform appearance onan etched or anodized surface caused by heterogeneities (variabilities) remaining in the metalfrom the casting, thermal processes or hot workingstages of fabrication.

Stress – Force per unit of area. Stress is normallycalculated on the basis of the original cross-sectional dimensions. The three kinds of stresses aretensile, compressive, and shear.

Stress Corrosion Cracking – See “Corrosion, StressCracking.”

Stress Relieving – The reduction of the effects ofinternal residual stresses by thermal or mechanicalmeans.

Stretcher Strain – See “Line, Luders.”

Striation – Longitudinal non-uniform coating thickness caused by uneven application of the liquidcoating.

Strip – This term is not recommended. The term“Sheet” is preferred.

Structural Streak – See “Streak, Structural.”

Suck-in – A defect caused when one face of a forging is sucked into fill a projection on the oppositeside.

Surface Tear – Minute surface cracks on rolledproducts which can be caused by insufficient ingotscalping.

Tail Mark – “See Mark, Roll Bruise.”

Tear, Speed – A series of surface cracks perpendicular to the extruding direction. Speed tearing normally occurs in corner radii or extremitiesof a section and is caused by localized high temperature.

Telescoping – Lateral stacking, primarily in onedirection, of warps in a coil so that the edges of thecoil are conical rather than flat. Improper alignment ofroll over which the metal passes before rewinding is

a typical cause. See also “Oscillation.”

Temper – The condition produced by either mechanical or thermal treatment, or both, and characterized by a certain structure and mechanicalproperties.

Tensile Strength – In tensile testing, the ratio of maximum load to original cross-sectional area. Alsocalled “Ultimate Strength.”

Tension Scratch – See “Scratch, Tension.”

Tolerance – Allowable deviation from a nominal orspecified dimension.

Tool – A term usually referring to the dies, mandrels,etc., used in the production of extruded or drawnshapes or tube.

Tooling Pad – See “Chucking Lug.”

Tooling Plate – A cast or rolled product of rectangular cross section of thickness 0.250 inch orgreater, and with edges either as-cast, sheared orsawed, with internal stress levels controlled toachieve maximum stability for machining purposes intool and jig applications.

Torn Surface – A deep longitudinal rub mark resulting from abrasion by extrusion or drawing tools.

Traffic Mark – Abrasion which results from relativemovement between contacting metal surfaces during handling and transit. A dark color from theabrasively produced aluminum oxide is usuallyobserved. A mirror image of a traffic mark isobserved on the adjacent contacting surface.

Transverse Bow – See “Bow, Transverse.”

Transverse Direction – A direction perpendicular tothe direction of working.

Tread Plate – Sheet or plate having a raised figuredpattern on one surface to provide improved traction.

Trim Inclusion – Edge trimming accidentally woundinto a roll of foil.

Tube – A hollow wrought product that is long in relation to its cross section, which is symmetrical andis round, a regular hexagon or octagon, elliptical, or square or rectangular with sharp orrounded corners, and that has uniform wall thickness except as affected by corner radii.

Tube, Arc-Welded – Tube made from sheet or platebutt welded by either gas-tungsten or gas-metal arc-welding method, with or without the use of fillermetal.

Tube Bloom – This term is not recommended. Theterm “Tube Stock” is preferred.

Tube Stock – A semifinished tube suitable for theproduction of drawn tube.




(562) 802-2721

Tube, Alclad – Composite tube composed of an aluminum alloy core having on either the inside oroutside surface a metallurgically bonded aluminumor aluminum alloy coating that is anodic to the core,thus electrolytically protecting the core against corrosion.

Tube, Brazed – A tube produced by forming andseambrazing sheet.

Tube, Butt-Welded – A welded tube, the seam ofwhich is formed by positioning one edge of the sheetagainst the other for welding.

Tube, Drawn – A tube brought to final dimensions bycold drawing through a die. (Note: This product maybe produced from either seamless or non-seamlessextruded stock or from welded stock.)

Tube, Embossed – A tube the outside surface ofwhich has been roll-embossed with a design in reliefregularly repeated in a longitudinal direction.

Tube, Extruded – A tube formed by hot extruding.(Note: This product may be either seamless or non-seamless.)

Tube, Finned – Tube which has integral fins or projections protruding from its outside surface.

Tube, Fluted – A tube of nominally uniform wallthickness having regular, longitudinal, concave corrugations with sharp cusps between corrugations.

Tube, Heat-Exchanger – A tube for use in apparatus in which fluid inside the tube will be heated or cooled by fluid outside the tube. The termusually is not applied to coiled tube or to tubes foruse in refrigerators or radiators.

Tube, Helical-Welded – A welded tube produced bywinding the sheet to form a closed helix and joiningthe edges of the seam by welding.

Tube, Lap-Welded – A welded tube the seam ofwhich is formed by longitudinally lapping the edgesof the sheet for welding.

Tube, Lock-Seam – A tube produced by forming andmechanically lock-seaming sheet.

Tube, Open-Seam – A shape normally producedfrom sheet of nominally uniform wall thickness andapproximately tubular form but having a longitudinalunjointed seam or gap of width not greater than 25percent of the outside diameter or greatest over-alldimension. Also referred to as “Butt-Seam Tube.”

Tube, Redraw – This term is not recommended. Theterm “Tube Stock” is preferred.

Tube, Seamless – A tube that does not contain anyline junctures (metallurgical welds) resulting from themethod of manufacture. (Note: This product may beproduced by die and mandrel or by hot piercerprocesses.)

Tube, Sized – A tube that, after extrusion, has beencold drawn a slight amount to minimize ovality.

Tube, Stepped Drawn – A drawn tube whose crosssection changes abruptly in area at intervals along itslength.

Tube, Structural – Tube commonly used for structural purposes.

Tube, Welded – A tube produced by forming andseam-welding sheet longitudinally.

Tubing – This term is not recommended. The term“tube” is preferred.

Tubing-Electrical Metallic – A tube having certainstandardized length and combinations of outsidediameter and wall thickness thinner than that of “RigidConduit,” commonly designated by nominal electricaltrade sizes, for use with compression-type fittings asa protection for electric wiring.

Tubular Conductor – A tubular product suitable foruse as an electric conductor.

Twist – (1) For rolled products, a winding departurefrom flatness. (2) For extrusions, a winding departurefrom straightness.

Two-Tone – A sharp color demarcation in the appearance of the metal due to a difference in thework roll coating.

Ultimate Tensile Strength – See “Tensile Strength.”

Vent Mark – A small protrusion on a forging resultingfrom the entrance of metal into a die vent hole.

Water Stain – See “Corrosion, Water Stain.”

Wavy Edge – See “Buckle, Edge.”

Weave – See “Oscillation.”

Web – (1) A single thickness of foil as it leaves therolling mill. (2) A connecting element between ribs,flanges, or bosses on shapes and forgings.

Weld Line – See “Seam, Extrusion.”

Weld, Incomplete – The junction line of metal thathas passed through a die forming a hollow profile(shape), separated and not completely rejoined. Flaretesting is a method of evaluating weld integrity.

Welding – Joining two or more pieces of aluminum byapplying heat or pressure, or both, with or withoutfiller metal to produce a localized union through fusionor recrystallization across the interface. (In cold welding, it is a solid state welding process in whichpressure is used at room temperature to produce coalescence of metals with substantialdeformation at the weld.)



[email protected]

(562) 802-2721

Welding Rod – A rolled, extruded, or cast round fillermetal for use in joining by welding.

Welding Wire – Wire for use as filler metal in joiningby welding.

Wettability Test – The degree to which a metal surface may be wet to determine the absence of orthe amount of residual rolling or added lubricants ordeposits on the surface.

Whip Marks – See “Mark, Whip.”

Whisker – See “Hair, Slitter.”

Wire – A solid wrought product that is long in relationto its cross section, which is square or rectangularwith sharp or rounded corners or edges, or is round,hexagonal, or octagonal, and whose diameter orgreatest perpendicular distance between parallelfaces is less than 0.375 inch.

Wire, Alclad – A composite wire product comprisedof an aluminum-alloy wire having on its surface a metallurgically bonded aluminum or aluminum-alloycoating that is anodic to the alloy to which it is bonded, thus electrolytically protecting the core alloyagainst corrosion.

Wire, Cold-Heading – Wire of quality suitable for usein the manufacture of cold-headed products such asrivets and bolts.

Wire, Drawn – Wire brought to final dimensions bydrawing through a die.

Wire, Extruded – Wire produced by hot extruding.

Wire, Flattened – Wire having two parallel flat surfaces and rounded edges produced by roll-flattening round wire.

Wire, Flattened and Slit – Flattened wire that hasbeen slit to obtain square edges.

Wire, Rivet – See “Wire, Cold-Heading.”

Work Hardening – See “Strain Hardening.”

Workability – The relative ease with which variousalloys may be formed by rolling, extruding, forging,etc.

Wrap, Loose – A condition in a coil due to insufficient tension which creates a small voidbetween adjacent wraps.

Wrinkle – See “Crease.”

Wrought Product – A product that has been subjected to mechanical working by such processesas rolling, extruding, forging, etc.

Yield Strength – The stress at which a materialexhibits a specified permanent set. The offset usedfor aluminum and its alloys is 0.2 percent of gaugelength. For aluminum alloys the yield strengths in tension and compression are approximately equal.

Documents

63063 002 stainless gradesQQS-763, AMS-QQS-763 PH 13-8 MO AMS-5629 Type 1, AMS-2300, Cap. of ASTM-A-564 Grade XM-13, STM-05-602 (Exc. Sonic some sizes check TR’s), HMS -6-1105 (Exc