2
Recommended: Hammer, Carpenter’s square, Clamp, Tape measure 1/2" Wrench Power drill with #2 Phillips bit BEFORE YOU BEGIN TOOLS YOU WILL NEED A D E C 4 – Table Legs 1 – Tabletop* 2 – Bench Seats* 2 – Diagonal Braces 2 – Bench Supports* 8 – Hex Nuts 8 – Carriage Bolts 8 – Washers 32 – 2-1/2" Screws B F H G I 6' PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS ©2019 Universal Forest Products, Inc. All rights reserved. 2801 East Beltline NE, Grand Rapids, MI 49525 10211_3/19 Outdoor Essentials is a registered trademark of Universal Forest Products, Inc. OutdoorEssentialProducts.com PARTS LIST ASSEMBLY H I THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO RE- PLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES. FOR DETAILS ON SAFE HANDLING AND WARRANTY INFORMATION, GO TO UFPI.COM/PTINFO. cleat * If your bench supports have beveled corners, be sure they face downward. PRO TIPS Use a hammer to fully seat bolts into holes PRO TIP Flush Flush Continuous water absorption and water loss in the wood can cause its natural defects to surface. To reduce the appearance of these natural defects and extend the life of your picnic table, apply a protective finish such as a semitransparent stain or waterproofing sealer. The table has approximately 86 square feet of surface area. Apply the finish following the stain or sealer manufacturer’s instructions and reapply every two years as needed. PRO TIPS Check out our blog to learn more about finishing your picnic table, along with other projects! OE.media/blog Connect with us: @OutdoorEssentialProducts @outdoor_essentials Mold occurs naturally on wood. If you receive a picnic table with mold on it, you can safely clean it with water and detergent or vinegar. 2 PEOPLE View our installation video at OE.media/table This table is made from construction grade lumber and may contain rough edges. Wear protective gear. MINUTES 45 It will take you about 45 minutes to complete. You’ll need two adults to safely assemble this picnic table. C C C C B B B B C - Center legs on tabletop - Hold legs tight to the cleat and tabletop - Drive in screws - Clamp legs to cleat before drilling - Predrill holes before drilling in screws 1 3 5 4 2 Insert bolts into bench supports Attach legs to tabletop with screws Attach bench seats with screws Attach diagonal braces with screws Attach legs to bench supports* CARE AND MAINTENANCE Do not fully tighten Hex nuts *Your kit may include parts with beveled corners. E B H H H B C A D I I C C A B B I I I C F F G G H H PRO TIP Use a carpenter’s square to confirm legs are square before drilling the diagonal brace in place. Fully tighten Hex nuts before drilling the diagonal brace in place. Center the brace Flip table up 2 PEOPLE PRO TIP Use a tape measure to confirm bench is centered.

6 PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS...1 – Cubierta de mesa* 4 – Patas de mesa C 2 – Asientos de banco* 2 – Soportes diagonales 2 – Soportes de banco* 8 – Tuercas hexagonales

  • Upload
    others

  • View
    3

  • Download
    0

Embed Size (px)

Citation preview

Page 1: 6 PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS...1 – Cubierta de mesa* 4 – Patas de mesa C 2 – Asientos de banco* 2 – Soportes diagonales 2 – Soportes de banco* 8 – Tuercas hexagonales

Recommended: Hammer, Carpenter’s square, Clamp, Tape measure

1/2" Wrench Power drill with #2 Phillips bit

6' PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS

©2018 Universal Forest Products, Inc. Assembled in the USA with imported fasteners. All rights reserved. 2801 East Beltline NE, Grand Rapids, MI 49525 800.598.9663 10211_9/18Outdoor Essentials is a registered trademark of Universal Forest Products, Inc. OutdoorEssentialProducts.com

PARTS LIST BEFORE YOU BEGIN

TOOLS YOU WILL NEED

A

D E

C4 – Table Legs1 – Tabletop*

2 – Bench Seats* 2 – Diagonal Braces

2 – Bench Supports*

8 – Hex Nuts

8 – Carriage Bolts

8 – Washers

32 – 2-1/2"Screws

ASSEMBLY

B

F

H

G

I

6' PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS

©2019 Universal Forest Products, Inc. All rights reserved. 2801 East Beltline NE, Grand Rapids, MI 49525 10211_3/19Outdoor Essentials is a registered trademark of Universal Forest Products, Inc. OutdoorEssentialProducts.com

PARTS LIST

ASSEMBLY

H I

THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO RE-PLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES. FOR DETAILS ON SAFE HANDLING AND WARRANTY INFORMATION, GO TO UFPI.COM/PTINFO.

cleat

* If your bench supports have beveled corners, be sure they face downward.

PRO TIPS

Use a hammer to fully seat bolts into holes

PRO TIP

Flush

Flush

Continuous water absorption and water loss in the wood can cause its natural defects to surface. To reduce the appearance of these natural defects and extend the life of your picnic table, apply a protective fi nish such as a semitransparent stain or waterproofi ng sealer.

The table has approximately 86 square feet of surface area. Apply the fi nish following the stain or sealer manufacturer’s instructions and reapply every two years as needed.

PRO TIPS

Check out our blog to learn more about fi nishing your picnic table, along with other projects!

OE.media/blog

Connect with us:

@OutdoorEssentialProducts

@outdoor_essentials

Mold occurs naturally on wood. If you receive a picnic table with mold on it, you can safely clean it with water and detergent or vinegar.

2 PEOPLE 1 HOUR

MINUTES

45

View our installation video at OE.media/table

This table is made from construction grade lumber and may contain rough edges. Wear protective gear.

2 PEOPLE 1 HOUR

MINUTES

45 It will take you about 45 minutes to complete.

You’ll need two adults to safely assemble this picnic table.

CC

C C

B B

BBC

- Center legs on tabletop

- Hold legs tight to the cleatand tabletop

- Drive in screws

- Clamp legs to cleat before drilling

- Predrill holes before drilling in screws

1

3

5

4

2Insert bolts into bench supports

Attach legs to tabletop with screws

Attach bench seats with screws

Attach diagonal braces with screws

Attach legs to bench supports*

CARE AND MAINTENANCE

Do not fully tighten Hex nuts

*Your kit may include parts with beveled corners.

E

B

H

H

H

B

C

A

DI

I

C

C

A

B

B

II

I

C

F

FG

G

H

H

PRO TIPUse a carpenter’s square to confi rm legs are square before drilling the diagonal brace in place.

Fully tighten Hex nuts before drilling the diagonal brace in place.

Center the brace

Flip table up2 PEOPLE 1 HOUR

MINUTES

45PRO TIPUse a tape measure to confi rm bench is centered.

Page 2: 6 PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS...1 – Cubierta de mesa* 4 – Patas de mesa C 2 – Asientos de banco* 2 – Soportes diagonales 2 – Soportes de banco* 8 – Tuercas hexagonales

Recomendadas: Martillo, escuadra de carpintero, abrazadera, cinta métrica

Llave inglesa de 1/2 pulg.

Taladro eléctrico con punta Philips #2

*Su kit puede incluir piezas con esquinas biseladas.

* Si los soportes de su banca tienen esquinas biseladas, asegúrese de que estén volteando hacia abajo.

6' PICNIC TABLE KIT ASSEMBLY INSTRUCTIONS

©2018 Universal Forest Products, Inc. Assembled in the USA with imported fasteners. All rights reserved. 2801 East Beltline NE, Grand Rapids, MI 49525 800.598.9663 10211_9/18Outdoor Essentials is a registered trademark of Universal Forest Products, Inc. OutdoorEssentialProducts.com

PARTS LIST ANTES DE COMENZAR

HERRAMIENTAS QUE NECESITARÁ

A

D E

C4 – Patas de mesa1 – Cubierta de mesa*

2 – Asientos de banco* 2 – Soportes diagonales

2 – Soportes de banco*

8 – Tuercas hexagonales

8 – Pernos de carrocería

8 – Arandelas

32 – Tornillos 6.4 cm. (2-1/2 pulg.)

ASSEMBLY

B

F

H

G

I

JUEGO DE MESA DE PICNIC DE 183 CM (6 PIES) INSTRUCCIONES DE ARMADO

©2019 Universal Forest Products, Inc. Todos los derechos reservados. 2801 East Beltline NE, Grand Rapids, MI 49525 10211_3/19Outdoor Essentials es una marca comercial registrada de Universal Forest Products, Inc. OutdoorEssentialProducts.com

LISTA DE PARTES

ARMADO

H I

LOS DIAGRAMAS E INSTRUCCIONES DE ESTE FOLLETO SON PARA FINES ILUSTRATIVOS SOLAMENTE Y NO ESTÁN DESTINADOS A REEMPLAZAR A UN PROFESIONAL MATRICULADO. CUALQUIER CONSTRUCCIÓN O USO DEL PRODUCTO DEBE ESTAR DE ACUERDO CON TODOS LOS CÓDIGOS LOCALES DE CONSTRUCCIÓN O DE ZON-IFICACIÓN. EL USUARIO ASUME TODOS LOS RIESGOS Y RESPONSABILIDADES ASOCIADOS CON LA CONSTRUCCIÓN O EL USO DE ESTE PRODUCTO. EL USUARIO O CONTRATISTA DEBE TOMAR TODAS LAS MEDIDAS NECESARIAS PARA GARANTIZAR LA SEGURIDAD DE TODAS LAS PERSONAS INVOLUCRADAS EN EL PROYECTO, QUE INCLUYEN PERO NO SE LIMITAN A, EL USO DEL EQUIPO DE SEGURIDAD APROPIADO. A EXCEPCIÓN DE LO CONTENIDO EN LA GARANTÍA LIMITADA POR ESCRITO, EL GARANTE NO PROPORCIONA NINGUNA OTRA GARANTÍA, YA SEA EXPRESA O TÁCITA, Y NO SERÁ RESPONSABLE DE NINGÚN DAÑO, INCLUIDOS DAÑOS CONSECUENTES. PARA OBTENER DETALLES SOBRE UN MANEJO SEGURO E INFORMACIÓN DE LA GARANTÍA, VISITE UFPI.COM/PTINFO.

listón

Use un martillo para meter los pernos completamente en los orifi cios

CONSEJO ÚTIL

A nivel

A nivel

La constante absorción y pérdida de agua en la madera puede hacer que surjan sus defectos naturales. Para reducir la aparición de estos defectos naturales y prolongar la vida útil de su mesa de picnic, aplique un acabado protector, como una mancha semitransparente o un sellador a prueba de agua.

La mesa tiene un área superfi cial aproximada de 8 metros cuadrados (86 pies cuadrados). Aplique el acabado siguiendo las instrucciones del fabricante de la mancha o el sellador y vuelva a aplicar cada dos años, cuando sea necesario.

CONSEJOS ÚTILES

¡Visite nuestro blog para ver más información sobre el acabado de su mesa de picnic y otros proyectos!

OE.media/blog

Conéctese con nosotros:

@OutdoorEssentialProducts

@outdoor_essentials

El moho aparece de manera natural en la madera. Si recibe una mesa de picnic con moho, puede limpiarlo con seguridad usando agua y detergente o vinagre.

2 ADULTOS 1 HOUR

MINUTOS

45

Vea nuestro video de instalación en OE.media/table

Esta mesa está fabricada con madera de construcción y puede tener bordes ásperos. Use equipo de protección.

2 ADULTOS 1 HOUR

MINUTOS

45Tardará unos 45 minutos para armarla.

Se necesitan dos adultos para armar esta mesa de picnic de manera segura.

CC

C C

B B

BBC

Use una escuadra de carpintero para confi rmar que las patas estén rectas antes de atornillar el soporte diagonal en su sitio.

- Centre las patas en la cubierta de la mesa

- Coloque las patas cerca del listón y la cubierta de la mesa

- Coloque los tornillos

- Fije las patas al listón con una abrazadera antes de taladrar

- Taladre orifi cios antes de insertar los tornillos

1

3

5

4

2Inserte los pernos en los soportes de las bancas

Fije las patas a la cubierta de la mesa con tornillos

Fije los asientos de las bancas con tornillos

Fije los soportes diagonales con tornillos

CUIDADO Y MANTENIMIENTO

No apriete las tuercas hexagonales por

completo

Fije las patas a los soportes de las bancas*

CONSEJO ÚTILCONSEJOS ÚTILES

E

B

H

H

H

B

C

A

DI

I

C

C

A

B

B

II

I

C

F

FG

G

H

H

Apriete por completo las tuercas hexago-nales antes de atornillar el soporte diagonal en su sitio.

Centre el soporte

Voltee la mesa a su posición correcta

2 ADULTOS 1 HOUR

MINUTOS

45Use una cinta métrica para asegurarse de que la banca está centrada

CONSEJO ÚTIL