11
1 Po Box 472110, Tulsa, OK 74147 USA Toll Free: 800-725-7311 918-447-1288 office 918-447-0188 fax www.mathey.com 5SA Saddle Machine Parts & Operating Manual Register product online @ www.mathey.com <http://www.mathey.com > ______________Machine Model ____________________ Serial # REVISED: AUGUST 2009 ©Mathey Dearman, Inc.

5SA Saddle Machine

Embed Size (px)

DESCRIPTION

Po Box 472110, Tulsa, OK 74147 USA Toll Free: 800-725-7311 918-447-1288 office 918-447-0188 fax www.mathey.com REVISED: AUGUST 2009 ©Mathey Dearman, Inc. ______________Machine Model ____________________ Serial # 1

Citation preview

1

Po Box 472110, Tulsa, OK 74147 USA Toll Free: 800-725-7311

918-447-1288 office 918-447-0188 fax www.mathey.com

5SA Saddle Machine Parts & Operating Manual

Register product online @ www.mathey.com <http://www.mathey.com>

______________Machine Model ____________________ Serial #

REVISED: AUGUST 2009 ©Mathey Dearman, Inc.

2

MATHEY DEARMAN INC. Safety Proper precautions should be taken when using the Short Saddle Cutting and Beveling Machine or any and all other heavy cutting and welding equipment. A little common sense goes a long way towards preventing accidents involving your Mathey Dearman Saddle Machine.

1. Make sure Ring and Pinion Gears are free from obstacles, especially hands and feet, before engaging machine.

2. Observe operation of machine to make sure loose clothing, tools, belts, etc. do not become entangled on the gear teeth or torch arm.

3. Fire is hot. Keep all flammable material, including hands and feet, as far from the path of the cutting torch as possible.

4. Keep all motor parts and accessories away from water to avoid electrocution.

Maintenance Your Mathey Dearman Pipe Cutting and Beveling Machine requires only minimal maintenance; however, these are precision machines. In order to achieve proper results, make sure your machine is handled with reasonable care and is kept clean and properly lubricated. The Ring Gear, Pinion Gears, and Drive Chains should be kept clear of slag and other trapped abrasives, especially sand and dirt. The Saddle, Ring Gear, and Cap Ring should be cleaned and the ring gear track surfaces should be coated with lubricant (Lubriplate 130-AA or equal) at intervals of 30 and 60 days, and before storing. The Drive Chains and Sprockets should be cleaned regularly and coated with a film of a light lubricant (WD-40 or similar).

During transporting or when not in use, the machine should be stored in a protective container such as a Mathey Dearman Machine Storage Box or the original factory shipping crate.

Mathey Dearman 5SA Pipe Cutting & Beveling Machine

Installation of Spacers on the 5SA Machine Saddle Install the correct Spacer Bolts (4 bolts) in the four holes in the 5SA Machine Saddle, with the Spacer end of the Bolts on the Bore (I.D.) side of the Saddle. The correct size Spacers for the pipe size to be cut or beveled must be used to align the machine firmly around the pipe. Spacer I.D. surfaces must be in solid contact with the O.D. pipe surface.

Bore Size (inside diameter) of 5SA Machine Saddle

30-1/2”

(775 mm)

Subtract actual OD of pipe 28” (711mm) Difference 2-1/2” (64mm) Divide Difference by two (2) 2-1/2” ÷ 2 = 1-1/4” (32mm)

3

The correct Spacer length (between outside diameter of pipe and inside diameter of saddle) is 1-1/4” (32mm).

Figure 1: Spacer Configuration for 26”, 28” & 30” pipe. (660, 711, & 762mm respectively)

Installation of 5SA Machine on Pipe Install the 5SA Machine Saddle squarely on the pipe, near the line to be cut or beveled (measure as needed). Place the Boomer Assembly (Figure 2) around the pipe on the open side of the Machine. Install the hooked end of the Boomer hooks into the Boomer Eye on one side of the Machine Saddle. The S Hook on the other end of the Chain hooks into the Boomer Eye on the other side of the Machine Saddle and is secured with the Cotter Pin. In order to get a stable installation, the Chain (3) must be adjusted on the S Hook so the Spring (2) is stretched approximately 3/4” to 1” (19-25mm) when the Boomer is closed. When the Chain is properly adjusted, close the Boomer (1).

Figure 2: Boomer Assembly Part # 03.0105.017 Item # Part Description Part # Quantity

1 Boomer 01-0258-001 1 2 Spring 01-0184-003 1 3 Chain 01-0577-006 1 4 Spring Snap 01-0258-003 1

Item # Part Description Part # Quantity 1 Spacer Bolt 03-0110-011 4 2 Spacer, 1” (25 mm) 04-0106-018 8 3 Spacer Bolt (24” Pipe) 03-0110-008 4

4

Figure 3: Torch Arm Torch Carrier Assembly Part Number: 03-0101-001 Part #: 03-0100-002

Installation of Torch Arm, Torch Carrier Assembly and Torch Install Torch Arm (Fig. 3, Item A) by attaching it to the two threaded studs located in the face of the 5SA Machine Ring Gear at the 12 o’clock position. Secure Torch Arm with the wing nuts on the studs. Install and secure Torch Carrier Assembly (Fig. 3, Item B) into the slot of the Torch Arm for an outward and for the Torch.

The Torch Clamp Base (Fig. 3 Item 1) is marked 0, 60, and 90. Use the ‘0’ position for square cuts (no bevel). For positions 60 and 90 make the appropriate bevel to produce a V groove of 60 and 90 degrees respectively when the two pipe ends are butted together. Install Torch in Torch Clamp (Fig. 3, Item 2) and adjust to a stand off distance recommended by the Torch manufacturer. Note: Before starting to cut or bevel, rotate Torch one full turn around the pipe to be sure Torch tip will clear all the way around the pipe.

Item #

Part Description Part # Qty

A Torch Arm 03-0101-001 1 Double Torch Arm Kit 03-0105-025 Opt

B Torch Carrier Assembly 03-0100-002 1 1 Torch Clamp Base 03-0100-003 1 2 Torch Clamp 03-0100-005 1 3 Clamp 03-0100-004 1 4 Screw Kit 03-0100-029 1

5

Figure 4: 5SA Machine – Manual Part # 03-0105-000 Item # Part Description Part # Qty.

1 Saddle 03-0105-001 1 2 Cap Ring 03-0105-003 1 3 Ring Gear 03-0105-002 1 4 Single Bearing Bracket Assembly (left) 03-0105-005 1 5 Single Bearing Bracket Assembly (right) 03-0105-004 1 6 Double Bearing Bracket Assembly 03-0105-007 1 7 Handle Tie Rod 03-0105-016 2 8 Boomer Eye 03-0101-017 2 9 Cap Screw, hex head, 5/16”, 18NC x 5/8” 10-56C0-058 11

10 Cap Screw, hex head, 3/8”, 16NC x 7/8” 10-38C0-078 9 11 Cap Screw, hex head, 3/8”, 16NC x 1-1/4” 10-38C0-114 4 12 Washer, flat, 3/8” 12-0038-F00 13

Drive Chain 03-0105-015 2 Washer, flat, 1/2” w/ Spacer Bolts 12-0012-F00 4 Nut, Hex 1/2” w/ Spacer Bolts 1H-12C0-000 4 Threaded Stud (Ring Gear) 01-0194-003 2 Wing Nuts, 5/16” 1W-56C0-000 2 Spring Pins, 3/16” x 1-1/4” 18-3160-114 2

Figure 6: Double Bearing Bracket Assembly

Part # 03.0105.010

Item #

Part Description Part # Qty

1 Bracket 03-0105-011 1 2 Crank Handle Assembly 03-0103-012 1 3 Crank Pinion 03-0105-012 1 4 Crank Gear and Double Sprocket 03-0105-014 1 5 Axle 03-0105-013 1 6 Bearings 01-0196-012 1

7 Spacer 04-0106-011 1

8 Spacer 04-0106-013 1

9 Set Collar, 1/2” 01-0185-005 1 10 Set Screw, 1/4” ,

20NC x 1/2” 19-14C0-012 4

11 Screw, round head 1/4”, 20NC x 1/2”

14-14C0-012 1

12 Washer, flat, 1/4” 12-0014-F00 1 13 Spring Pin, 3/16” x 1-1/4” 18-3160-114 1 14 Spiral Ring, 1/2” 01-0179-014 1

6

Figure 5: Single Bearing Bracket Assembly Left Side Assy: Part# 03-0105-004

Right Side Assy: Part# 03-0105-005

Item # Part Description Part # Qty.

1 Bracket 03-0105-006 1 2 Sprocket 03-0105-008 1 3 Axle 03-0105-009 1 4 Pinion Gear 03-0105-007 1 5 Spacer 04-0106-013 1 6 Bearing 01-0196-002 2 7 Set Screw, 5/16”, 18NC x 5/16 19-56C0-056 1

8 Set Screw, 1/4”, 20NC x 1/4” 19-14C0-014 2 9 Spiral Ring, 1/2” 01-0179-014 1

10 Spring Pin, 3/16” x 1” 18-3160-100 1 11 Spring Pin, 3/16” x 1-1/4” 18-3160-114 1

Item # Part Description Part # Qty 1 Gear Motor 03-0201-053 1 2 Motor Mounting Bracket 03-0103-028 1 3 Bracket Mounting Bar 03-0105-024 1 4 Drive Sprocket 03-0101-008 1 5 Driven Sprocket 03-0103-026 1 6 Chain 03-0104-017 1 7 Motor Control Box 03-0203-009 1 8 Spacer 04-0106-051 1 9 Cap Screw, hex head, 1/4”, 20NC x

5/8” 10-14C0-058 3

10 Nuts, hex, 1/4” 1H-14C0-000 3 11 Washer, flat, 1/4” 12-0014-F00 3 12 Cap Screw, hex head, 5/16”, 18NC x

1/2” 10-56C0-012 2

13 Cap Screw, hex head, 3/8”, 16NC x 1-1/4”

10-38C0-114 6

14 Saddle 03-0105-001 1 15 Cap Ring 03-0105-003 1 16 Ring Gear 03-0105-002 1 17 Single Bearing Bracket Assembly (left) See pg. 6 1 18 Single Bearing Bracket Assembly

(right) See pg. 6 1

19 Double Bearing Bracket Assembly See pg. 6 1 20 Handle Tie Rod 03-0105-016 2 21 Boomer Eye 03-0101-017 2 22 Cap Screw, hex head, 5/16”, 18NC x

5/8” 10-56C0-058 11

23 Cap Screw, hex head, 3/8”, 16NC x 7/8”

10-38C0-078 7

24 Washer, flat 1/4” 12-0038-F00 4 25 Washer, internal lock, 1/4” 12-0014-100 3 26 Washer, internal lock, 3/8” 12-0038-100 2 27 Washer, lock, 3/8” 12-0038-L00 2

28 Set Screw, 5/16”, 18NC x 5/16” 19-5600-056 1

Figure 7: 5SA Machine – Motorized, Part #03-0105-M00

7

TROUBLESHOOTING – MANUAL MACHINE TROUBLESHOOTING – MOTORIZED MACHINE Symptom Possible Cause(s) Corrective Action

Gear Motor does not rotate

No electrical power at outlet. Select another electrical outlet. Wire broken between Plug and Motor. Replace Electrical Cord.

DC Cord had electrical short. Replace Motor Control Box (part # 03.0203.009)

Fuse blown Replace fuse with 2 amp fuse (part # 01.0427.008)

Motor lags at low speed Motor operating below power curve. Increase size of cutting tip so that

motor speed can be increased.

Machine vibrates Motor Mounting Screws are loose. Tighten Motor Mounting Screws. Motor and Pinion Shafts are out of alignment. Realign motor to coupling.

29 Washer, flat, 3/8” 12-0038-F00 1

8

Procedure for Timing the Ring Gear to the Pinion Gears & Installation of NEW S Drive Chains

This process requires that you purchase 2 new Axles, part number 03-0103-008. Double drilling the Axles severely weakens them and will cause failure after a very short period of time. 1. Remove both Spring Pins (11) from the Right and Left Single Bearing Bracket

Sprockets (2). 2. Loosen the Socket Set Screw (6) in both the Right and Left Single Bearing Brackets. 3. Remove the Sprockets (2) from the Axles (4) 4. Separate the Axles (4) and Pinion Gears (3) from the Bearing Brackets. 5. Remove the Spring Pins (10) and press the Axles out of the Pinion Gears (3) 6. Press the New Axles (4) into the Pinion Gears (3) until they are flush with the end of

the Pinion Gear. 7. Drill through the Pinion Gear (3) and Axle (4) with a 3/16” drill. 8. Insert the Spring Pin (10) into the drilled hole in the Pinion Gear (3).

Note: Make sure the Spring Pin (10) is all the way through the Axle (4) and into the other side of the Pinion Gear (3).

9. Insert the Axles back into the Bearings (5) in the Bearing Brackets, until the Pinion Gears (3) are flush with the end of the bearing

10. Install the Sprocket (2) onto the Axle (4) until it contacts with the face of the bearing (6). Make sure that it rotates freely.

Note: Do not tighten the Set Screws or drill and install the Spring Pins at this time.

11. Remove the outer Hex Head Cap Screws (11) from the Right and Left Single Bearing Bracket Sprocket (2).

12. Loosen the Inner Hex Head Cap Screws (11) from the Right and Left Single Bearing Bracket Sprocket so that Bracket will rotate.

13. Rotate the Single Bearing Bracket Assemblies toward the center of the machine. 14. Place the Drive Chains on the Sprockets (2) of the Single Bearing Bracket

Assemblies and the Double Sprocket (3) of the Double Bearing Bracket Assembly. 15. Move the Right and Left Single Bearing Brackets downward, install the outer Hex

Head Cap Screws (11) in the Bearing Bracket Assemblies and tighten the Screw only snugly. Do not tighten them at this time.

Note: The use of Hex Head Cap Screws (11) of the proper length is very important, if the screws are too long they will contact Ring Gear and you will not be able to rotate the Ring Gear.

16. Move the Single and Double Bearing Bracket downward and outward until the chain is taunt with a soft face hammer. Adjust the Right and Left Single Bearing Bracket Assemblies so there is .007” – .010” play between the Ring Gear (3) and Pinion Gear (3) of the Single Bearing Bracket Assembly.

Note: When pressure is applied to the top of the chain, it should flex about 3/16”.

17. Rotate the Ring Gear (3) clockwise (as viewed from the front of the machine) until

9

the gap in the Ring Gear is at the 12:00 position. 18. Rotate the Pinion Gears (3) of the Bearing Bracket Assemblies so that they are

evenly spaced in the teeth of the Ring Gear. 19. Tighten one of the Socket Head Set Screws (6) in each Sprocket (2) of the single

Bearing Bracket Assemblies. 20. Rotate the Ring Gear (3) one full revolution in the clockwise and counterclockwise

direction checking the entry of the Ring Gear (3) into the Pinion gears (3).

Note: The entry of the Pinion Gears (3) into the Ring Gear (3) should be smooth and without hesitation. The Pinion Gears should not push or pull the Ring Gear as it enters or leaves the Pinion Gears.

21. Tighten the Hex Head Cap Screw (11) that holds the Single and Double Bearing Brackets to the Saddle Assembly.

Note: Care should be taken not to over torque the Hex Head Cap Screws (11) as there are only 3 – 4 threads of engagement in the Saddle Assembly

22. Place the Tie Rod Handle (7) on the backside of the Single and Double Bearing Bracket and insert the 2 Flat Head Screws (12) in the holes of the Tie Rod Handle, install the Hex Nuts (13) and tighten.

23. Recheck the entry of the Ring Gear (3) into the Pinion Gear (3) to insure that smooth and without hesitation.

24. The Machine is now ready for operation. A Note on Back Beveling Switching Mathey Dearman machines to back beveling is quick and easy. Place Torch as close to Saddle as possible without placing flame directly on or near saddle when back beveling. Rotate the Torch Clamp Base and Torch 180 degrees in the Torch Arm and re-tighten with thumb screw and clamp. The Torch will then be positioned for back beveling.

Caution: When back beveling, the cutting flame and “hot” zone of the pipe are directed toward the machine. It is very important that the Torch be positioned as far as possible to the opposite end of the Torch Arm to prevent the heat from damaging the machine Saddle and Ring Gear.

10

Warranty If any merchandise sold hereunder (except merchandise manufactured by other persons or firms) by Mathey Dearman, Inc. (the “Company”) is not in accordance with specifications shown on the order within customarily accepted tolerances, or is defective on account of workmanship or material, and if such merchandise is returned at the customer’s expense and rise, to the Company’s manufacturing facility (or at the Company’s option, is returned to a repair facility authorized by the Company), within ninety (90) days after the Company’s date of shipment thereof, the Company will, at its option, replace or repair the merchandise. This agreement, however, is upon the conditions: (A) that the customer promptly notifies the Company in writing of any claim under this agreement, setting forth in detail any such claimed defect. (B) That the Company be afforded a reasonable opportunity to examine the merchandise and to investigate the claimed defect at the Company’s manufacturing facility or at an authorized repair facility, the Company shall not be, in any event, liable for damages beyond the price paid by the customer for such defective merchandise; specifically but without limitation, the Company may fulfill its obligations under this Agreement by tendering such purchase price at any time. THE COMPANY SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, PUNITITVE, OR EXEMPLARY DAMAGES. This agreement does not obligate the Company to bear any transportation charges in connection with the replacement or the repair of defective merchandise. As to any item manufactured by other persons or firms, the Company agrees to present a request for adjustment for repair to such manufacturer, and the customer agrees that the liability of the Company shall not exceed any adjustment with respect to which such manufacturer accepts responsibility. THE ABOVE AGREEMENT IS IN LIEU OF ALL WARRANTIES, EXPRESSED OR IMPLIED AND IT IS AGREED THAT THERE IS NO EXPRESSED OR IMPLIED WARRANTY BY THE COMPANY AS TO THE FITNESS, MERCHANTABILITY CAPACITY, OR EFFICIENCY OF ANY MERCHANDISE SOLD, AND THAT THERE ARE NO ORAL OR WRITTEN EXPRESSED OR IMPLIED WARRANTIES MADE IN CONNECTION WITH ANY SALE BY THE COMPANY. No modification or addition to this agreement, either before or after the contract of sale, shall be made except on written authority of the President or Vice President of the Company.

11

C.I.A. Mathey Italiana S.r.l. Via Isonzo, 26 - 20050 S. Damiano di Brugherio (MI)

Phone: +39 039 831019/2020021 • Fax: +39 039 2020079 [email protected] • www.ciamathey.com