Upload
edcosta5647
View
215
Download
0
Embed Size (px)
Citation preview
7/31/2019 560062667 x 122908 x 43
1/11
Usage of
Quanum 2.4Ghz Telemetry
System (Volt/Amp/Temp/mAh)
V2
Presented by kenaf010
7/31/2019 560062667 x 122908 x 43
2/11
Receiver power onPush at same time.
Binding button
Power button
7/31/2019 560062667 x 122908 x 43
3/11
When the receiver is not switched on even if
you push two button at the same time.
A buzzer sounds when you push the power switch
if the battery of the receiver is left.
NO buzzer -> Maybe Battery charge will be not
left. Recharging necessary.You put an attached USB cable in the receiver anda PC, and please recharge receiver. The receiver
will work in charge one hour.
7/31/2019 560062667 x 122908 x 43
4/11
BindingWhile Holding down transmitter bind
Button,
Binding button of transmitter
Insert the balance port of the transmitter
in batteries balance plug.
Do not get a wrong direction + -
Green LED flash
7/31/2019 560062667 x 122908 x 43
5/11
Binding completeWait for approximately two seconds.
When a bind completes, the voltage is displayed
7/31/2019 560062667 x 122908 x 43
6/11
Configuration mode You can change setting of the telemetry system configuration.
There are eight items
1. Temperature unit C or F
2. Capacity display mode : remain capacity or remain %
3. Total capacity: 100mAh-32000mAh
4. Remain capacity alarm : 0-100%
5 Total voltage alarm 5.0 - 25.8V (6cell)The alarm beep-beep emits and display flashes under setting voltage.
6. Cell voltage alarm level1 2.5V-4.2V
The alarm beep-beep" emits and display flashes under setting cell voltage.
7. Cell voltage alarm level2 2.5V-4.2V
The alarm beep-beep-beep-beep emits and display flashes under setting cell
voltage.
8. Reload default
7/31/2019 560062667 x 122908 x 43
7/11
Configuration modeEnter configuration mode
Push power and binding button at same time when the voltage is displayed.
Select program Item
Push binding button. The item changes in loops when pushing the button.Change value
Push power button. The value changes in loops when pushing the button.
Exit configuration mode
Push power and binding button at same time once again.
Select itemChange value
The setting changes immediately
when changing the value.
7/31/2019 560062667 x 122908 x 43
8/11
Quanum 2.4Ghz voltage telemetry
transmitter Current & Heat Sensor
This is front view!!
Do not get a wrong front and back.
Power IN
Power OUT+
-
-
+
To TX
To
Temp sensor
S+
-
S+-
This is front view!!TX
Temp sensor The illustration of HobbyKing is back side
7/31/2019 560062667 x 122908 x 43
9/11
Attach the connector to the sensor unit
Power IN
Power OUT+-
-
+
To TX
To
Temp sensor
S+-
S+-
Battery
ESC
+-
Solder the connector and the Power IN/OUT terminals of the sensor unit with a ditch
ditch ditch
Do not get a wrong IN/OUT and +/- to ESC and battery !!
7/31/2019 560062667 x 122908 x 43
10/11
TestingAttach the temperature sensor to sensor unit. The receiver power ON.
Connect the batteries balance plug while holding down transmitter binding button.
The display changes when pushing the binding button.
7/31/2019 560062667 x 122908 x 43
11/11
GOOD LUCK !!