QUADRAPLEX RECEPTACLE, NEMA 5-20R, MOUNT AT +18" AFF.

DUPLEX RECEPTACLE, NEMA 5-20R, MOUNT AT +18" AFF.

SYMBOL DESCRIPTIONSYMBOL DESCRIPTION

DESCRIPTIONSYMBOL

WALL-MOUNTED LIGHT FIXTURE.

CEILING MOUNTED. DIRECTIONAL ARROWS INDICATED.

EXIT FIXTURE ON EMERGENCY POWER

LED FIXTURE.

MOUNT AT +48" AFF.

SINGLE POLE AND 3-WAY LIGHT SWITCH, RATED 120/277 VOLT, 20A.

SPECIAL EQUIPMENT RECEPTACLE, MOUNT AT +18" AFF.

JUNCTION BOX.

FIRE ALARM AUDIO/VISUAL ANNUNCIATOR, ## INDICATES STROBE CANDELA RATING.

CEILING MOUNTED.

OTHERWISE NOTED.

W - WALL MOUNTED, +54" AFF.

GFI - GROUND FAULT PROTECTED

SUBSCRIPT LETTER BESIDE SWITCH OR RECEPTACLE SYMBOL INDICATES THE TYPE AS FOLLOWS:

3R - WEATHER PROOF (NEMA 3R)

AFF - ABOVE FINISHED FLOOR

FOLLOW MOUNTING HEIGHTS INDICATED IN THE ELECTRICAL LEGEND UNLESS OTHERWISE NOTED ON THE

DRAWINGS. ADDITIONALLY, MEASURE ALL MOUNTING HEIGHTS FROM THE DEVICE CENTER-LINE UNLESS

VERIFY EXACT FEEDER LOCATIONS FOR MECHANICAL EQUIPMENT AFTER COMPLETION OF MAJOR

MECHANICAL WORK.

ALL EQUIPMENT CONNECTIONS ARE INDICATED IN THEIR APPROXIMATE LOCATIONS. VERIFY EXACT

LOCATIONS OF ALL CONNECTIONS WITH OTHER TRADES SUPPLYING EQUIPMENT TO AVOID CONFLICTS

AT INSTALLATION.

LOCATE ALL SWITCHES FOR LOCAL CONTROL OF LIGHTING ON STRIKE SIDE OF SINGLE

DOORS UNLESS OTHERWISE INDICATED.

ALL CONDUITS RUNS INDICATED ARE DIAGRAMMATIC. COORDINATE CONDUIT ROUTING IN ALL SPACES

WITH OTHER TRADES PRIOR TO ACTUAL INSTALLATION.

1.

2.

3.

4.

5.

6.

7.

PROVIDE AS-BUILT DRAWINGS INDICATING ACTUAL BRANCH CIRCUIT BREAKER ARRANGEMENT. ALSO

PROVIDE TYPE-WRITTEN PANELBOARD DIRECTORIES INDICATING ACTUAL BRANCH CIRCUIT BREAKER

PROVIDE SPECIFIC BREAKER ARRANGEMENT FOR THE PANELBOARDS WHEREVER PHYSICALLY POSSIBLE.

ARRANGEMENT.

WG - WIRE GUARD

##

UNO - UNLESS NOTED OTHERWISE.

GROUND FAULT PROTECTED DUPLEX RECEPTACLE, NEMA 5-20R,

MOUNT AT +18" AFF UNLESS NOTED OTHERWISE.

JUNCTION BOX LOCATION FOR TELEPHONE/DATA OUTLET MOUNTED 18" ABOVE

FINISHED FLOOR, UNLESS OTHERWISE NOTED OR REQUIRED BY SITE CONDITIONS.

MOUNT FLUSH IN FINISHED SPACES OR SURFACE IN UNFINISHED SPACES. ROUTE AN

EMPTY 3/4" CONDUIT WITH PULL STRING TO A POINT ABOVE AN ACCESSIBLE CEILING.

GFI

RECESSED POKE THROUGH FLOOR BOX. 2 HOUR RATED, REFER TO FIRE RATED POKE

THROUGH DETAIL, THIS SHEET.BASIS OF DESIGN HAS BEEN HUBBELL SYSTEM ONE.

PROVIDE ALL COMPONENTS NECESSARY FOR A COMPLETE INSTALLATION. INCLUDING

DEVICES/COVERS, ETC. FIELD VERIFY EXACT LOCATION PRIOR TO INSTALLATION.

3.88

Ø

[98.6]

12.11

307.6]

2.37

[60.2]

.25

[6.35]

3/4" E

MT

2.29

[58.2]

2X

.41

[10.4]

SCALE: NOT TO SCALE

UL CHARACTERISTICS

LISTING UL FILE NUMBER

OUTLET BOX E31999

FIRE RESISTANCE RR8429

FOR USE IN 1, 1

1

2

, 2, 3 OR 4 HOUR RATED REINFORCED FLOORS.

UL SPACING RESTRICTIONS: MINIMUM OF 2 FEET ON CENTER AND NOT

MORE THAN ONE UNIT PER 65 SQUARE FEET OF FLOOR AREA IN EACH

SPAN.

APPLICATION DATA:

MOUNTED IN 4 INCH CORED CONCRETE DIAMETER THROUGH HOLE.

FLOOR THICKNESS RANGE: 2

1

4

" TO 7"

NONESCALE:

· INSTALLS IN 4" CORE DRILL.

· UL LISTED FOR USE IN 1-4 HOUR RATED FLOORS.

STEP DOWN INSTALLATION CLIPS ALLOW THE FITTING TO BE INSTALLED

OR REMOVED FROM THE FLOOR ABOVE.

BARRIER EXPANDS DURING FIRE CONDITIONS TO

MAINTAIN THE FLOOR'S FIRE RATING.

ADJUSTABLE LOWER FIRE BARRIER ACCOMODATES CONCRETE FLOOR

THICKNESSES FROM 2-1/4" TO 7"

FEATURES DUAL 1" EMT CONDUIT TUBES FOR INCREASED CABLE

CAPACITY.

J

,

DUPLEX RECEPTACLE TO BE DEMOLISHED.

SPECIAL EQUIPMENT RECEPTACLE TO BE DEMOLISHED.

JUNCTION BOX TO BE DEMOLISHED.

J

DUPLEX RECEPTACLE TO REMAIN.

TELEPHONE/DATA EXISTING TO REMAIN.

SPECIAL EQUIPMENT RECEPTACLE TO REMAIN.

FACP

EXISTING FIRE ALARM PANEL TO REMAIN.

,

LED FIXTURE WIRED FROM LIFE-SAFETY PANELBOARD.

PP

POWER POLE POWERED FURNITURE CONNECTION PROVIDED WITH THE

FURNITURE SYSTEM. FIELD VERIFY EXACT LOCATION PRIOR TO INSTALLATION.

NOTES:

COMBINATION OCCUPANCY SENSOR/WALL SWITCH UNIT

N

G

H

DUAL-PASSIVE WITH MICROPHONICS (SOUND)

OCCUPANCY SENSOR WITH INTEGRAL SWITCHES

(SWITCHES TO ADJUST LIGHT LEVELS ONLY).

MANUFACTURED BY SENSORSWITCH OR

APPROVED SUBSTITUTE. MODEL SELECTED TO

COVER AREA.

BALLAST(S)/LAMP(S), TYP.

SCALE: NONE

1. LINE VOLTAGE WIRING SHALL BE #12 MIN., INSTALLED IN CONDUIT.

2. CONTROL WIRING SHALL BE AS RECOMMENDED BY LIGHTING CONTROLLER MANUFACTURER, AND

SHALL BE INSTALLED IN CONDUIT.

3. FOR AREAS WITH THREE-WAY SWITCHING OR DIMMING CONNECT CONTROLLER(S) TO LINE SIDE OF

SWITCHES.

4. PROVIDE ALL NECESSARY COMPONENTS FOR A COMPLETE INSTALLATION.

5. WIRE AS PER MANUFACTURER'S SPECIFICATIONS.

NOTES:

CEILING MOUNTED OCCUPANCY SENSOR

N

G

H

DUAL-PASSIVE WITH MICROPHONICS (SOUND)

CEILING MOUNTED OCCUPANCY SENSOR.

MANUFACTURED BY SENSORSWITCH OR

APPROVED SUBSTITUTE. MODEL SELECTED TO

COVER AREA.

BALLAST(S)/LAMP(S), TYP.

SCALE: NONE

TERMINATE CONCEALED ABOVE

ACCESSIBLE CEILING WITH NYLON

BUSHING

FINISHED CEILING

FINISHED FLOOR

SLAB

1-1/2" CONDUIT MINIMUM SIZE

WALL/PARTITION FACE

2.5" DEEP 2-GANG OUTLET BOX WITH

SINGLE GANG PLASTER RING

WALL/PARTITION CAVITY

(1)1-1/2" CONDUIT FOR DATA/AV

CONNECTION BY OTHERS.

(1) 1" CONDUIT FOR POWER WIRING.

NOTE: ALL NEW WORK

ABOVE CEILING SHALL BE

PLENUM RATED

NO SCALE

6"

6"

F

1. LINE VOLTAGE WIRING SHALL BE #12 MIN., INSTALLED IN CONDUIT.

2. CONTROL WIRING SHALL BE AS RECOMMENDED BY LIGHTING CONTROLLER MANUFACTURER, AND

SHALL BE INSTALLED IN CONDUIT.

3. FOR AREAS WITH THREE-WAY SWITCHING OR DIMMING CONNECT CONTROLLER(S) TO LINE SIDE OF

SWITCHES.

4. PROVIDE ALL NECESSARY COMPONENTS FOR A COMPLETE INSTALLATION.

5. WIRE AS PER MANUFACTURER'S SPECIFICATIONS.

PROJECT INFORMATION

USE GROUP: B

CONSTRUCTION TYPE: 1A

FLOOD PLAIN: NO

FULLY SPRINKLERED BUILDING

· OWNER - DPW

900 E. Broad Street, Richmond, VA 23219

· Engineer - Lu+Smith Engineeers (CONTACT: DAWEN LU)

(804)925-2600, dlu@lsengineers.net,

5243 Hickory Park Dr., Ste C., Glen Allen, VA 23059

ALL METALLIC CONDUITS SHALL TERMINATE WITH INSULATED THROAT CONNECTORS OR PLASTIC BUSHINGS TO PROTECT WIRING INSULATION

BEFORE WIRING IS PULLED IN.

ALL CABLING NOT IN RACEWAYS OR ARMORED SHALL BE PLENUM RATED.

ALL WIRE IN CONDUIT FILL SIZING SHALL BE BASED UPON THE USE OF TYPE OF WIRE AND INSULATION USED PER NEC.

TYPE AC AND ACL ARMORED CABLE MAY BE USED FOR BRANCH CIRCUITS SERVING SERVICES WITHIN INTERIOR PARTITIONS AND EXTERIOR

WALLS. INSTALLATION SHALL CONFORM WITH ARTICLE 320 OF THE NEC.

ALL CONDUCTORS SHALL BE SOLID COPPER. ALL CONDUCTORS SHALL BE INSULATED FOR 600 VOLTS.

BRANCH CIRCUIT WIRING INSULATION FOR POWER AND LIGHTING SHALL GENERALLY BE TYPE THW OR THWN.

GROUNDING CONDUCTORS SHALL BE INSTALLED WHEREVER WIRING IS INSTALLED IN ALL RACEWAYS. NO EXCEPTIONS!

PVC RACEWAYS SHALL BE ALLOWED BELOW FLOOR SLAB AND SITE ELECTRICAL ONLY. PVC NOT ALLOWED ABOVE FINISHED FLOOR OR

FINISHED GRADE.

FLEXIBLE LIQUID-TIGHT CONDUIT SHALL BE USED FOR CONNECTIONS TO ALL MOTORS, DRY-TYPE TRANSFORMERS AND ANY EQUIPMENT WHERE

REQUIRED BECAUSE OF VIBRATION OR RELATIVE MOTION. ALL RACEWAYS SHALL BE CONCEALED WHEREVER POSSIBLE. CONDUIT SHALL BE

THE SIZE REQUIRED FOR THE CONDUCTORS BUT IN NO CASE SHALL IT BE SMALLER THAN 3/4 INCH TRADE SIZE.

WIRE AND CABLE (600 VOLTS AND BELOW)

D.

E.

C.

B.

A.

H.

G.

F.

A NYLON PULL CORD SHALL BE INSTALLED IN ALL CONDUITS IN WHICH CONDUCTORS ARE NOT INSTALLED. A 10 INCH MINIMUM LENGTH OF THE

CORD SHALL EXTEND OUT OF EACH END OF THE CONDUIT.

CONDUIT MAY BE RUN EXPOSED IN MECHANICAL EQUIPMENT AND UTILITY SPACES. ELSEWHERE, IT SHALL BE CONCEALED ABOVE CEILINGS, IN

SHAFTS, AND IN FURRED SPACES.

IN GENERAL, CONDUITS 2 INCHES OR LARGER, AND CONDUIT IN FLOOR SLABS SHALL BE HEAVY WALL RIGID TYPE. THE MINIMUM SIZE CONDUIT

USED SHALL BE 3/4 INCH. LARGER SIZES SHALL BE USED PER FILL REQUIRED BY THE NATIONAL ELECTRICAL CODE.

RACEWAYS SHALL BE INSTALLED AS A COMPLETE SYSTEM AND SHALL BE CONTINUOUS FROM OUTLET TO OUTLET, UNLESS NOTED OTHERWISE.

RACEWAYS SHALL BE MECHANICALLY AND ELECTRICALLY CONNECTED TO ALL BOXES AND FITTINGS. RACEWAYS AND BOXES SHALL BE

SUPPORTED FROM STRUCTURAL STEEL AND NOT SUPPORTED FROM THE CEILING GRID OR ROOF DECKING PER NEC. DEFLECTION AND

EXPANSION COUPLINGS SHALL BE USED WHEN RACEWAYS CROSS EXPANSION JOINTS.

RACEWAYS AND FITTINGS

E.

D.

C.

B.

A.

ALL WIRING THAT IS REQUIRED TO BE INSTALLED IN RACEWAY SHALL BE ELECTRICAL METALLIC TUBING (EMT), SUBJECT TO THE RESTRICTIONS

OF THE NEC. INTERMEDIATE METAL CONDUIT (IMC), (HOT DIP GALVANIZED) SHALL BE USED IN LOCATIONS EXPOSED TO THE WEATHER. THE

USE OF TYPE MC CABLE SHALL BE LIMITED TO LIGHTING AND RECEPTACLE BRANCH CIRCUITS, AS ALLOWABLE BY THE NEC. ALL HOMERUNS TO

PANELBOARDS SHALL BE IN CONDUIT. TERMINATE TYPE MC CABLE OUTSIDE OF ELECTRICAL ROOM AND TRANSITION TO CONDUIT BEFORE

ENTERING ELECTRICAL ROOM.

C. THE FIRE ALARM CONTRACTOR SHALL FURNISH THE QUANTITY OF DOCUMENTS

REQUIRED BY THE AUTHORITY HAVING JURISDICTION OF P.E. DESIGNED, SEALED AND

SIGNED FIRE ALARM PLANS.

A. THE FIRE ALARMS CONTRACTOR SHALL OBTAIN A SEPARATE PERMIT. ALL

INFORMATION SHALL BE PROVIDED ON THE PLANS PER THE REQUIREMENTS OF

AUTHORITY HAVING JURISDICTION.

B. THE FIRE ALARM SYSTEM IS EXISTING AND SHALL BE EXTENDED AND ADJUSTED TO

THE NEW LAYOUT WITHIN THE LIMITS OF WORK. BECAUSE OF THE LIMITED FIRE ALARM

INSTALLATION, THIS PROJECT DOES NOT CONTAIN ANY BOOK FIRE ALARM

SPECIFICATIONS. THE FOLLOWING SHALL BE A PART OF THE FIRE ALARM WORK, BUT IS

NOT LIMITED TO:

1. PROVIDE ADDITIONAL FIRE ALARM DEVICES AS INDICATED ON PLANS

2. CONNECT FIRE ALARM DEVICES TO EXISTING FIRE ALARM SYSTEM INITIATING

AND NOTIFICATION CIRCUITS.

3. PROVIDE COMPLETE WIRING TO ALL NEW FIRE ALARM DEVICES.

4. PROVIDE COMPLETE BATTERY CALCULATIONS AS IT RELATES TO THE EXTENSION

OR ADDITION TO THE EXISTING NEW FIRE ALARM SYSTEM.

5. PROVIDE VOLTAGE DROP CALCULATIONS.

6. INSTALLATION SHALL BE IN COMPLIANCE WITH BASE BUILDINGS FIRE ALARM

SYSTEM MANUFACTURERS INSTRUCTIONS.

D. THE FIRE ALARM CONTRACTOR SHALL PROVIDE TO THE ARCHITECT/ENGINEER, A RECORD

SET OF APPROVED SHOP DRAWINGS FROM THE AUTHORITY HAVING JURISDICTION WHICH

COMPLY WITH THE VUSBC AND NFPA 72.

LIGHT FIXTURE SCHEDULE

TYPE DESCRIPTION MANUFACTURER CATALOG NUMBER LAMP INPUT VOLTS MOUNTING NOTES

NO. WATTS TYPE WATTS

A 2X2 LINEAR LEDCOOPER 22AC-A-LD4-44-UNV-L835

1 44 LED 44 277 RECESSED NOTE 2

B 2X4 LINEAR LEDCOOPER 24AC-A-LD4-55-UNV-L835

1 55 LED 55 277 RECESSED NOTE 2

C 2X4 LINEAR LEDCOOPER 4WSNLED-LD4-44SL-F-UNV-L835-CD1-U

1 44 LED 44 277 SURFACE CEILING NOTE 2

D LED DOWNLIGHTCOOPER H2750ICAT-ML5606827

1 20 LED 20 120 RECESSED NOTE 2

- - - - - - - - - - -

NOTE 1

X EXIT SIGN SURE-LITES APX7-R 1 3 LED 3 277 CEILING SEE PLAN

FOR DIRECTION

REMARKS:

1.PROVIDE FACES AND ARROWS AS NECESSARY

2. PROVIDE ALL COMPONENTS NECESSARY FOR A COMPLETE INSTALLATION.

3. NOT USED.

Xref 053-BDR.dwg

LEGEND, SCHEDULEAND DETAILS

E0.01

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

"G" LEVEL

MEZZ LEVEL

5TH FLOOR

10TH FLOOR

15TH FLOOR

PENTHOUSE

20A/1P

20A/1P

25A/3P

100A/3P

100A/3P

100A/3P

100A/3P

100A/3P

150A/3P

EMERGENCY LIFE SAFETY LOADS

PANEL

"ELS15"

(4)2/0, 1#2GND., 2"C.

EMERGENCY LIFE SAFETY LOADS

PANEL

"ELS10"

(4)2/0, 1#2GND., 2"C.

EMERGENCY LIFE SAFETY LOADS

PANEL

"ELS5"

(4)1/0, 1#3GND., 2"C.

EMERGENCY LIFE SAFETY LOADS

PANEL

"ELSM"

EMERGENCY LIFE SAFETY LOADS

PANEL

"ELSG"

(4)1/0, 1#6GND., 2"C.

(4)3, 1#8GND., 1-1/4"C.

LIFE SAFETY

ATS-LS

400A/3P

400A/3P

(2)SETS (4)3/0, #3GND., 2" C FROM

EXISTING GENERATOR

DISTRIBUTION PANELBOARD

400A/3P

(2)SETS (4)3/0, #3GND., 2" C FROM "MSB-1"

NO SCALE

NOTES:

A. ALL CONNECTIONS SHOWN ARE EXISTING TO REMAIN FOR

REFERENCE ONLY.

Xref 053-BDR.dwg

PARTIAL EMERGENCYONE-LINE DIAGRAM

E0.02

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

2000A

3P

MAIN SWITCHBOARD "MSB-1"

4000A, 277/480-VOLT

800A

3P

300A

3P

600A

3P

400A

3P

BU

SD

UC

T 'A

' - 2000A

MAIN SWITCH 'MSS-1'

4000A

100KAIC

TO EXISTING LOADS

PANEL

"DR4A"

400-AMP

PANEL

"L4A"

225-AMP

PANEL

"L4D"

"G" LEVEL

2ND-3RD FLOORS

4TH FLOOR

UPPER FLOORS

PANEL

"R4A"

100-AMP

PANEL

"R4B"

100-AMP

PANEL

"R4C"

100-AMP

PANEL

"R4D"

100-AMP

NO SCALE

XFMR

480-120/208V

"TR4"

112.5KVA

100A/3P

100A/3P

150A/3P

TO DOMINION XFMR

175A

3P

"NDLGB"

800A, 277/480-VOLT

XFMR

"TG2"

112.5KVA

"DRGB"

400A, 120/208-VOLT

400A

3P

175A

3P

"DLGA"

600A, 277/480-VOLT

600A

3P

XFMR

"TG2"

112.5KVA

200A

3P

"DRGA"

400A, 120/208-VOLT

400A

3P

200A

3P

PANEL

"L1C"

200A

3P

PANEL

"L1D"

200A

3P

PANEL

"L1A"

200A

3P

PANEL

"L1B"

PANEL

"R1A"

200A

3P

PANEL

"R1B"

200A

3P

PANEL

"R1C"

200A

3P

PANEL

"R1G"

RATED 22,000AIC

1ST FLOORS

200A

3P

PANEL

"RGA"

PANEL

"RGA1"

GENERAL NOTES:

A. ALL CONNECTIONS SHOWN ARE EXISTING TO REMAIN FOR

REFERENCE ONLY UNLESS NOTED OTHERWISE.

PANEL

"R2B"

EXISTING

EXISTING

EXISTING EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTINGEXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

60/3

PANEL

"R1GA"

RATED 22,000AIC

NEW

NOTES:

PROVIDE NEW 30-POLE, 120/208-VOLT, 3-PHASE, 4-WIRE,

60-AMP MAIN LUG ONLY PANELBOARD. REFER TO PANEL

SCHEDULES FOR MORE INFORMATION.

1

1

Xref 053-BDR.dwg

PARTIAL ONE-LINEDIAGRAM

E0.03

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

System No. C-AJ-1388

SECTION A-A

1. Floor or Wall Assembly Min 4-1/2 in. thick reinforced lightweight or normal weight (100-150 pcf) concrete. Wall may also be constructed

of any UL Classified Concrete Blocks*. Max area of opening 224 sq in. with max dimension of 32 in.

See Concrete Blocks (CAZT) in the Fire Resistance Directory for names of manufacturers.

2. Conduit One or more nom 4 in diam (or smaller) steel electrical metallic tubing or steel conduit to be installed either concentrically or

eccentrically within the firestop system. The space between conduits or tubes shall be min 0 in. (point contact) to max 1/2 in. The annular

space between the conduit or tube and periphery of opening shall be min 0 in. (point contact) to max 2-3/4 in. Conduit or tube to be

rigidly supported on both sides of floor or wall assembly.

Conduit - Nom 4 in. diam (or smaller) steel electrical metallic conduit or steel conduit.

3. Fill, Void or Cavity Material*- Foam Min 5 in. thickness of fill material applied within the annulus, extending 1/2 in. above the top surface

of the floor or both surfaces of wall and overlapping the concrete 1/2 in. on all sides of the opening.

HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC -- CP 620 Fire Foam

*Bearing the UL Classification Mark

A

Reproduced by HILTI, Inc. Courtesy of

Underwriters Laboratories, Inc.

January 23, 2002

F RATING = 2-HR

T RATING = 0-HR

A

12

3

Hilti Firestop Systems

C

CL

ASS IF IED

R

Classified by

Underwriters

Laboratories, Inc.

to UL 1479 and

CAN/ULC-S115

US

System No. C-AJ-1226

SECTION A-A

A

Reproduced by HILTI, Inc. Courtesy of

Underwriters Laboratories, Inc.

January 07, 2015Hilti Firestop Systems

1. Floor or Wall Assembly — Min 4-1/2 in. (114 mm) thick reinforced lightweight or normal weight (100-150 pcf or 1600-2400 kg/m³)

concrete. Wall may also be constructed of any UL Classified Concrete Blocks*. Max diam of opening is 32 in. (813 mm).

2. Metallic Sleeve — (Optional) Nom 32 in. (813 mm) diam (or smaller) Schedule 40 (or heavier) steel sleeve cast or grouted into floor or

wall assembly, flush with floor or wall surfaces or extending a max of 3 in. (76 mm) above floor or beyond both surfaces of wall.

2A. Sheet Metal Sleeve — (Optional) Max 6 in. (152 mm) diam, min 26 ga. galv steel provided with a 26 ga galv steel square flange spot

welded to the sleeve at approx mid-height, or flush with bottom of sleeve in floors, and sized to be a min of 2 in. (51 mm) larger than the

sleeve diam. The sleeve is to be cast in place and may extend a max of 4 in. (102 mm) below the bottom of the deck and a max of 1 in.

(25 mm) above the top surface of the concrete floor.

2B. Sheet Metal Sleeve — (Optional) - Max 12 in. (305 mm) diam, min 24 ga galv steel provided with a 24 ga galv steel square flange spot

welded to the sleeve at approx mid-height, or flush with bottom of sleeve in floors, and sized to be a min of 2 in. (51 mm) larger than the

sleeve diam. The sleeve is to be cast in place and may extend a max of 4 in. (102 mm) below the bottom of the deck and a max of 1 in.

(25 mm) above the top surface of the concrete floor.

3. Through-Penetrant — One metallic pipe, tube or conduit to be installed either concentrically or eccentrically within the firestop system.

The annular space between penetrant and periphery of opening shall be min 0 in. (point contact) to max 1-7/8 in. (48 mm). Penetrant may

be installed with continuous point contact. Penetrant to be rigidly supported on both sides of floor or wall assembly. The following types

and sizes of metallic penetrants may be used:

A. Steel Pipe — Nom 30 in. (762 mm) diam (or smaller) Schedule 10 (or heavier) steel pipe.

B. Iron Pipe — Nom 30 in. (762 mm) diam (or smaller) cast or ductile iron pipe.

C. Copper Pipe — Nom 6 in. (152 mm) diam (or smaller) Regular (or heavier) copper pipe.

D. Copper Tubing — Nom 6 in. (152 mm) diam (or smaller) Type L (or heavier) copper tubing.

E. Conduit — Nom 6 in. (152 mm) diam (or smaller) steel conduit.

F. Conduit — Nom 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing (EMT).

4. Firestop System — The firestop system shall consist of the following:

A. Packing Material — Min 4 in. (102 mm) thickness of min 4 pcf (64 kg/m³) mineral wool batt insulation firmly packed into opening as a

permanent form. Packing material to be recessed from top surface of floor or sleeve or from both surfaces of wall or sleeve as

required to accommodate the required thickness of fill material.

B. Fill, Void or Cavity Material* — Sealant — Min 1/4 in. (6 mm) thickness of fill material applied within the annulus, flush with top

surface of floor or sleeve or with both surfaces of wall or sleeve. At the point or continuous contact locations between penetrant and

concrete or sleeve, a min 1/4 in. (6 mm) diam bead of fill material shall be applied at the concrete or sleeve/ pipe penetrant interface

on the top surface of floor and on both surfaces of wall.

HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — FS-One Sealant or FS-ONE MAX Intumescent Sealant

* Indicates such products shall bear the UL or cUL Certification Mark for jurisdictions employing the UL or cUL Certification (such as

Canada), respectively.

A

2

34B

3

14B

4A

C

CL

ASS IF IED

R

Classified by

Underwriters

Laboratories, Inc.

to UL 1479 and

CAN/ULC-S115

USANSI/UL1479 (ASTM E814)

CAN/ULC S115

F Rating — 3 HrF Rating — 3 Hr

T Rating — 0 HrFT Rating — 0 Hr

L Rating At Ambient — Less Than 1

CFM/sq ft

FH Rating — 3 Hr

L Rating At 400 F — 4 CFM/sq ftFTH Rating — 0 Hr

L Rating At Ambient — Less Than 1

CFM/sq ft

L Rating At 400 F — 4 CFM/sq ft

Hilti Firestop Systems

System No. W-L-1054

SECTION A-A

A

Reproduced by HILTI, Inc. Courtesy of

Underwriters Laboratories, Inc.

January 23, 2015

A

1A3

2 1B

C

CL

ASS IF IED

R

Classified by

Underwriters

Laboratories, Inc.

to UL 1479 and

CAN/ULC-S115

USANSI/UL1479 (ASTM E814)

CAN/ULC S115

F Ratings —1 and 2 Hr (See Items 1 and 3) F Ratings — 1 and 2 Hr (See Items 1 and 3)

T Rating — 0 Hr FT Rating — 0 Hr

L Rating at Ambient — Less Than 1 CFM/sq ft FH Ratings —1 and 2 Hr (See Items 1 and 3)

L Rating at 400 F — Less Than 1 CFM/sq ft FTH Rating — 0 Hr

FTH Rating — 0 Hr

L Rating at Ambient — Less Than 1 CFM/sq ft L

Rating at 400 F — Less Than 1 CFM/sq ft

1. Wall Assembly — The 1 or 2 hr fire-rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner

specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire Resistance Directory and shall include the

following construction features:

A. Studs — Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom 2 by 4 in. (51 by 102

mm) lumber spaced 16 in. (406 mm) OC. Steel studs to be min 2-1/2 in. (64 mm) wide and spaced max 24 in. (610 mm) OC. When

steel studs are used and the diam of opening exceeds the width of stud cavity, the opening shall be framed on all sides using lengths

of steel stud installed between the vertical studs and screw-attached to the steel studs at each end. The framed opening in the wall

shall be 4 to 6 in. (102 to 152 mm) wider and 4 to 6 in. (102 to 152 mm) higher than the diam of the penetrating item such that, when

the penetrating item is installed in the opening, a 2 to 3 in. (51 to 76 mm) clearance is present between the penetrating item and the

framing on all four sides.

B. Gypsum Board* — 5/8 in. (16 mm) thick, 4 ft (122 cm) wide with square or tapered edges. The gypsum board type, thickness,

number of layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire

Resistance Directory. Max diam of opening is 32-1/4 in. (819 mm) for steel stud walls. Max diam of opening is 14-1/2 in. (368 mm) for

wood stud walls.

The F and FH Ratings of the firestop system are equal to the fire rating of the wall assembly.

2. Through-Penetrants — One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop system.

The annular space shall be min 0 in. to max 2-1/4 in. (57 mm). Pipe may be installed with continuous point contact. Pipe, conduit or

tubing may be installed at an angle not greater than 45 degrees from perpendicular. Pipe, conduit or tubing to be rigidly supported on

both sides of wall assembly. The following types and sizes of metallic pipes, conduits or tubing may be used:

A. Steel Pipe — Nom 30 in. (762 mm) diam (or smaller) Schedule 10 (or heavier) steel pipe.

B. Iron Pipe — Nom 30 in. (762 mm) diam (or smaller) cast or ductile iron pipe.

C. Conduit — Nom 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing or 6 in. (152 mm) . diam steel conduit.

D. Copper Tubing — Nom 6 in. (152 mm) diam (or smaller) Type L (or heavier) copper tubing.

E. Copper Pipe — Nom 6 in. (152 mm) diam (or smaller) regular (or heavier) copper pipe.

3. Fill, Void or Cavity Material* — Sealant — Min 5/8 in. (16 mm) thickness of fill material applied within the annulus, flush with both

surfaces of wall. At the point or continuous contact locations between pipe and wall, a min 1/2 in. (13 mm) diam bead of fill material shall

be applied at the pipe wall interface on both surfaces of wall.

HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — FS-One Sealant or FS-ONE MAX Intumescent Sealant

* Indicates such products shall bear the UL or cUL Certification Mark for jurisdictions employing the UL or cUL Certification (such as

Canada), respectively.

Hilti Firestop Systems

System No. W-L-1206

SECTION A-A1. Wall Assembly — The fire-rated gypsum board/stud wall assembly shall be constructed of the materials and in the manner described in

the individual U400, V400 or W400 Series Wall and Partition Design in the UL Fire Resistance Directory and shall include the following

construction features:

A. Studs — "C-T" shaped studs 1-5/8 in. (41 mm) wide by 2-1/2 in. (64 mm) deep, fabricated from 25 MSG galv steel, spaced max 24

in. (610 mm) OC.

B. Gypsum Board* — One layer of nom 1 in. (25 mm) thick, 24 in. (610 mm) wide gypsum liner and one or two layers of nom 5/8 in. (16

mm) thick, 4 ft. (1.27 m) wide gypsum board with square or tapered edges. The gypsum board types, number of layers, fastener type

and sheet orientation shall be as specified in the individual Wall and Partition Design. Max diam of opening is 10-1/2 in. (267 mm).

1A. Wall Assembly — As an alternate to the above wall assembly, the 1 or 2 Hr fire rated gypsum board/stud wall assembly shall be

constructed of the materials and in the manner specified in the individual U300, U400 or V400 Series Wall and Partition Designs in the UL

Fire Resistance Directory and shall include the following construction features:

A. Studs — Wall framing may consist of either wood studs or steel channel studs. Steel studs to be min 2-1/2 in. (64 mm) wide and

spaced max 24 in. (610 mm) OC. Wood studs to consist of nom 2 by 4 in. (51 by 102 mm) lumber spaced 16 in. (406 mm) OC.

B. Gypsum Board* — Thickness, type, number of layers and fasteners as required in the individual Wall and Partition Design. Max diam

of opening is 10-1/2 in. (267 mm).

The hourly F, FH Ratings of the firestop system are equal to the hourly fire rating of the wall assembly in which it is installed.

2. Metallic Sleeve — Max 10-1/2 in. (267 mm) diam cylindrical sleeve fabricated from min 0.016 in. (0.41 mm) thick (28 gauge) galv sheet

steel and having a min 1 in. (25 mm) lap along the longitudinal seam. Length of steel sleeve to be equal to thickness of wall. Sleeve

installed by coiling the sheet steel to a diam smaller than the through opening, inserting the coil through the opening and releasing the coil

to let it uncoil against the circular cutouts in the gypsum board layers. Sleeve may also be formed of No. 8 steel wire mesh having a min 1

in. (25 mm) lap along the longitudinal seam.

3. Through-Penetrants — One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop system.

An annular space of min 0 in. (0 mm, point contact) to max 1-7/8 in. (48 mm) is required within firestop system. Pipe, conduit or tubing to

be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes, conduits or tubing may be used:

A. Steel Pipe — Nom 8 in. (203 mm) diam (or smaller) Schedule 10 (or heavier) steel pipe.

B. Iron Pipe — Nom 8 in. (203 mm) diam (or smaller) cast or ductile iron pipe.

C. Conduit — Nom 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing or 4 in. (102 mm) diam steel conduit.

D. Copper Tubing — Nom 4 in. (102 mm) diam (or smaller) Type L (or heavier) copper tubing.

E. Copper Pipe — Nom 4 in. (102 mm) diam (or smaller) Regular (or heavier) copper pipe.

F. Flexible Steel Conduit+ — Nom 2 in. (51 mm) diam (or smaller) flexible steel conduit.

See Flexible Metal Conduit (DXUZ) category in the Electrical Construction Equipment Directory for names of manufacturers.

4. Firestop System — The firestop system shall consist of the following:

A. Packing Material — Min 1-5/8 or 2-1/4 in. (41 or 57 mm) thickness of min 4 pcf (64 kg/m³) mineral wool batt insulation firmly packed

into sleeve on one side of the wall as permanent form for 1 and 2 Hr walls, respectively. Packing material to be recessed from the

room side of wall to accommodate the required thickness of fill material. In alternate wall assembly, packing material to be flush with

either side of the wall and recessed from the other side of the wall to accommodate the required thickness of fill material.

B. Fill, Void or Cavity Material — Sealant* — Min 1-1/2 in. (38 mm) thickness applied within sleeve, flush with the surface of wall. At the

point contact location between pipe and wall, a min 1/2 in. (13 mm) diam bead of fill material shall be applied at the pipe/wall interface.

HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC — FS-ONE Sealant or FS-ONE MAX Intumescent Sealant

* Indicates such products shall bear the UL or cUL Certification Mark for jurisdictions employing the UL or cUL Certification (such as

Canada), respectively.

+Bearing the UL Listing Mark

A

Reproduced by HILTI, Inc. Courtesy of

Underwriters Laboratories, Inc.

January 22, 2015

A

3 2

4B

4A

1 4B3

2

4B

C

CL

ASS IF IED

R

Classified by

Underwriters

Laboratories, Inc.

to UL 1479 and

CAN/ULC-S115

USANSI/UL1479 (ASTM E814)

CAN/ULC S115

F Rating — 1 and 2 Hr (See Items 1 and 4) F Rating — 1 and 2 Hr (See Items 1 and 4)

T Rating — 0 Hr FT Rating — 0 Hr

FH Rating — 1 and 2 Hr (See Items 1 and

4)

FTH Rating — 0 Hr

2-HR RATED FIREWALL

PATH OF EGRESS

TENANT RENOVATIONS ON THE FOLLOWING FLOORS IN AN

EXISTING HIGH-RISE OFFICE BUILDING.

1ST FLOOR (2,500 SQ. FT)

THE BUILDING HAS A BUSINESS USE CLASS AND IS DESIGNED FOR

PROFESSIONAL OFFICES.

THIS BUILDING IS FULLY SPRINKLERED.

BUILDING DESCRIPTION

ELECTRICAL CODE

HANDICAPPED ACCESSIBILITY

BUILDING CODES

2012 VIRGINIA REHABILITATION CODE

2011 NATIONAL ELECTRICAL CODE (NEC)

AMERICANS WITH DISABILITIES ACT

ACCESSIBILITY GUIDELINES (ADAAG), JULY 23,

2004

X24 X29X27 X30

1/8" = 1'-0"

Xref 053-BDR.dwg

DETAILS

E0.04

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

1/8" = 1'-0"

1/8" = 1'-0"

J

J

J

PP

PP

J

J

EXISTING PNL 'R1G'

EXISTING PNL 'R1G'

EXISTING PNL 'L1C'

EXISTING

PNL 'A1'

SP

SP

S

SP

SP

SP

SP

SP

SP

S

F

F

F

F

GENERAL NOTES

A. VERIFY ALL INFORMATION PRIOR TO ROUGH-IN.

B. A SITE SURVEY WAS CONDUCTED TO LOCATE ALL DEVICES AFFECTED BY THIS

SCOPE OF WORK, FIELD VERIFY ALL DEVICES AFFECTED DURING THIS SCOPE OF

WORK AND PROVIDE ALL WORK NECESSARY TO ACHIEVE A COMPLETE

INSTALLATION.

C. CONTRACTOR SHALL XRAY THE EXISTING FLOOR SLAB PRIOR TO CUTTING FOR

FLOOR BOX LOCATIONS TO VERIFY THAT NO EXISTING INFRASTRUCTURE WILL

BE DAMAGED.

D. CIRCUIT INFORMATION IS BASED ON EXISTING PANELBOARD DIRECTORY. FIELD

VERIFY EXISTING INFORMATION AND PROVIDE ALL CHANGES NECESSARY TO

MAINTAIN CONTINUITY TO ALL DEVICES/CONNECTIONS THAT ARE EXISTING TO

REMAIN.

E. DURING THE DEMOLITION PHASE, THERE HAVE (73) 2X4 FLUORESCENT FIXTURES

FOR A TOTAL OF 5,694-WATTS REMOVED. DURING THE NEW WORK PHASE,

THERE HAS BEEN (22) 2X4S AND (29)2X2S ADDED FOR A TOTAL OF 2486-WATTS

ADDED FOR A TOTAL OF 3208-WATTS REMOVED FROM EXISTING SERVICE.

PLAN KEY NOTES

EXISTING PANELBOARD IS LOCATED IN EXISTING TO BE DEMOLISHED

WALL. CONTRACTOR SHALL EXTEND/REROUTE EXISTING FEEDER

WIRING AND CONDUIT ALL EXISTING TO REMAIN CONNECTIONS TO

NEW LOCATION. FIELD VERIFY EXACT SIZE PRIOR TO DEMOLITION.

1

1

FLOOR PLAN -DEMOLITION

E1.01

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

PLANNORTH

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

X24 X29X27 X30

GENERAL NOTES

A. VERIFY ALL INFORMATION PRIOR TO ROUGH-IN.

B. FIELD VERIFY ALL DEVICES AFFECTED DURING THIS SCOPE OF WORK

AND PROVIDE ALL WORK NECESSARY TO ACHIEVE A COMPLETE

INSTALLATION.

C. CONTRACTOR SHALL XRAY THE EXISTING FLOOR SLAB PRIOR TO

CUTTING FOR FLOOR BOX LOCATIONS TO VERIFY THAT NO EXISTING

INFRASTRUCTURE WILL BE DAMAGED.

1/2" = 1'-0"

1/8" = 1'-0"

'RG1A'

'LGA'

'RGA'

'RGC'

'LGB'

'RGB'

'DRGA1'

'DLGA1'

'DLGA2'

'DRGA2'

'XFMR'

NO SCALE

BOXES 4-11/16" SQUARE

POWER JUNCTION BOX.

(2) 1" CONDUITS STUBBED

ABOVE ACCESSIBLE

CEILING

(TELE/DATA)

NONESCALE:

MINIMUM 3/4" FLEXIBLE

CONDUIT (POWER) & 1"

FLEXIBLE CONDUIT

CONNECTIONS (TELE/DATA)

TO SYSTEMS FURNITURE.

LENGTH AS REQUIRED.

SIDE VIEW

EXISTING/ NEW

WALL OR COLUMN

CONDUIT SIZE AS

REQUIRED FOR CIRCUITS:

REQUIRED. COORDINATE

WITH TENANT'S SYSTEMS

FURNITURE VENDOR.

ELEVATION VIEW

1 1/4" DIAMETER RUBBER LINED

GROMMET AT COVER PLATE.

FACE PLATE

Circuit 1 Hot

Circuit 1/2/3 Neutral

Circuit 1/2/3 Ground

Circuit 2 Hot

Circuit 3 Hot

Circuit 4 Hot

Circuit 4 Neutral

Circuit 4 Ground

CIRCUIT 1 (Hot)

CIRCUIT 1/2/3 (Neutral)

CIRCUIT 1/2/3 (Ground)

CIRCUIT 2 (Hot)

CIRCUIT 4 (Hot)

CIRCUIT 4 (Neutral)

CIRCUIT 4 (Ground)

SYSTEMS FURNITURE

INTERNAL WIRING

SYSTEMS FURNITURE BASE

FEED JUNCTION BOX

CONTRACTOR WIRING.

REFER TO POWER FLOOR

PLAN FOR CIRCUIT

NUMBERS.

DETAIL SYSTEMS FURNITURE

CIRCUIT 3 (Hot)

12" A

.F

.F

.

4 1/4" X 4 1/4" JB 4 1/4" X 4 1/4" JB

WIRING DIAGRAM NOTES:

· CONFIRM SYSTEMS FURNITURE WIRING CONFIGURATION WITH TENANT'S

SYSTEMS FURNITURE VENDOR.

· CIRCUITS 1,2,3 MUST BE IN A-PHASE, B-PHASE, C-PHASE ROTATION.

PLAN KEY NOTES

WALL INFEED POWER CONNECTION FOR SYSTEMS FURNITURE.

BASIS OF DESIGN HAS BEEN 8-WIRE SYSTEM. REFER TO DETAIL

THIS SHEET FOR MORE INFORMATION. PROVIDE ALL COMPONENTS

NECESSARY FOR A COMPLETE INSTALLATION.

WALL INFEED DATA CONNECTION FOR SYSTEMS FURNITURE.

PROVIDE ALL COMPONENTS NECESSARY FOR A COMPLETE

INSTALLATION.

EXISTING PANELBOARD IS LOCATED IN EXISTING TO BE

DEMOLISHED WALL. CONTRACTOR SHALL EXTEND/REROUTE

EXISTING FEEDER WIRING AND CONDUIT ALL EXISTING TO REMAIN

CONNECTIONS TO NEW LOCATION. FIELD VERIFY EXACT SIZE

PRIOR TO DEMOLITION.

E.C. SHALL RE-FEED EXISTING AUTOMATIC DOOR OPENER. E.C.

SHALL REFER TO EXISTING NAMEPLATE FOR MORE INFORMATION.

E.C. SHALL PROVIDE JUNCTION BOX WITH 1" CONDUIT TO ABOVE

CEILING ACCESS SPACE FOR DOOR CONTROLS (PROVIDED BY

OWNER).

1

2

HUDDLE ROOM

113

CUSTOMER

SERVICE

125

OPERATIONS

MANAGER

101

ENGINEER

102

PROGRAM

MGR.

103

ENGINEER

105

ADMIN. PROJ.

ANALYST

107

CIRCULATION

104

KITCHENETTE

106

CIRCULATION

104

CONFERENCE

ROOM

109

CIRCULATION

108

WAITING

110

CIRCULATION

112

LOBBY

111

JSIVS78TKJSI

JSIVS78TKJSI

JSIVL1678SOJSI

JSIVL1678SOJSI

JSIVL2448ELRJSI

JSIVL2448ELRJSI

JSIVL3066RDFJSI

JSIVL3066RDFJSI

J

J

J

J

J J

+42"/GFCI

+42"/GFCI

J J

(E) PNL 'R1G'

EXISTING PNL 'R1G'

EXISTING PNL 'L1C'

(RELO)

PNL 'A1'

R1G-2,4,6,8

R1GA-1

3

3

R1GA-3

R1GA-5

NEW

PNL

'R1GA'

R1GA-7

R1GA-9

R1GA-2

R1GA-4

R1GA-6

R1GA-11

R1GA-13

R1GA-8

R1GA-10

R1GA-12

R1GA-15

R1GA-17R1GA-19

R1GA-21

R1GA-23

1

2

1

2

2

1

2

1

4

4

J

J

R1GA-25

5

5

5

PANELBOARD SCHEDULE L1C EDPLS

125 AMP MLO 480 Y / 277 V 3PH 4 W MOUNT: RECESSED PANEL ASSEMBLY RATED: 35 KAIC

CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC A B C CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC

1

50/3 EXIST EXISTING WATER HEATER

- - - - - 10 12 2 20/1 EXIST EXISTING LTG 2.2 - - - - -

3 - - - - - 10 12 4 20/1 EXIST EXISTING LTG 2.2 - - - - -

5 - - - - - 10 12 6 20/1 EXIST EXISTING LTG 2.2 - - - - -

7 20/1 (4)#12, (1)#12 GND, 3/4"C TERMINAL BOXES SUITE 115 - - - - - 0.8 2.8 8 20/1 EXIST EXISTING LTG 2.0 - - - - -

9 20/1 - SPARE - - - - - - 2.0 10 20/1 EXIST EXISTING LTG 2.0 - - - - -

11 20/1 - SPARE - - - - - - 2.0 12 20/1 EXIST EXISTING LTG 2.0 - - - - -

13 20/1 - SPARE - - - - - - 2.0 14 20/1 EXIST EXISTING LTG 2.0 - - - - -

15 20/1 - SPARE - - - - - - 2.0 16 20/1 EXIST EXISTING LTG 2.0 - - - - -

17 20/1 - SPARE - - - - - - 2.0 18 20/1 EXIST EXISTING LTG 2.0 - - - - -

19 20/1 - SPARE - - - - - - 2.0 20 20/1 EXIST EXISTING LTG 2.0 - - - - -

21 20/1 - SPARE - - - - - - 2.0 22 20/1 EXIST EXISTING LTG 2.0 - - - - -

23 20/1 - SPARE - - - - - - 2.0 24 20/1 EXIST EXISTING LTG 2.0 - - - - -

25 - - SPACE ONLY - - - - - - 2.0 26 20/1 EXIST EXISTING LTG 2.0 - - - - -

27 - - SPACE ONLY - - - - - - 2.0 28 20/1 EXIST EXISTING LTG 2.0 - - - - -

29 - - SPACE ONLY - - - - - - 2.0 30 20/1 EXIST EXISTING LTG 2.0 - - - - -

31 - - SPACE ONLY - - - - - - 2.0 32 20/1 EXIST EXISTING LTG 2.0 - - - - -

33 - - SPACE ONLY - - - - - - 2.0 34 20/1 EXIST EXISTING LTG 2.0 - - - - -

35 - - SPACE ONLY - - - - - - 2.0 36 20/1 EXIST EXISTING LTG 2.0 - - - - -

37 - - SPACE ONLY - - - - - - 2.0 38 20/1 EXIST EXISTING LTG 2.0 - - - - -

39 - - SPACE ONLY - - - - - - 2.0 40 20/1 EXIST EXISTING LTG 2.0 - - - - -

41 - - SPACE ONLY - - - - - - - 42 - - SPARE - - - - - -

- - - - - 31 A B C 125 41 - - - - -

LOAD TYPE CONNECTED LOAD KVA DEMAND KVA PHASE A KVA 25 90 PHASE A AMPS

INTERIOR LTG 41 51 PHASE B KVA 24 87 PHASE B AMPS

EXTERIOR LTG - - PHASE C KVA 22 80 PHASE C AMPS

RECEPTACLES - - TOTAL CONNECTED KVA: 71

AC / HEAT PUMP - - LIGHTING FEEDER DEMAND = 125% PER 2011 NEC 210.19(A)(1) TOTAL DEMAND KVA: 82

ELECTRIC HEAT - - RECEPTACLE DEMAND LOAD PER 2011 NEC TABLE 220.44

KITCHEN: - -

MISC: 31 31 TOTAL CONNECTED AMPS: 86

25% OF LARGEST MOTOR (XXX, XX HP): - TOTAL DEMAND AMPS: 98

PANELBOARD SCHEDULE R1G FED FROM DRGB

250 AMP MLO 208 Y / 120 V PH 4 W MOUNT: SURFACE PANEL ASSEMBLY RATED: KAIC

CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC A B C CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC

1 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 2 20/1 (4)#12, (1)#12 GND, 3/4"C SYSTEMS FURNITURE - - 1.5 - - -

3 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 4 20/1 (4)#12, (1)#12 GND, 3/4"C SYSTEMS FURNITURE - - 1.5 - - -

5 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 6 20/1 (4)#12, (1)#12 GND, 3/4"C SYSTEMS FURNITURE - - 1.5 - - -

7 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 8 20/1 (4)#12, (1)#12 GND, 3/4"C SYSTEMS FURNITURE - - 1.5 - - -

9 20/1 EXISTING EXISTING - - 1.5 - - - 1.5 10 20/1 - SPARE - - - - - -

11 20/1 EXISTING EXISTING - - 1.5 - - - 1.5 12 20/1 - SPARE - - - - - -

13 20/1 EXISTING EXISTING - - 1.5 - - - 6.4 14

60/3

(4)#6, (1)#10 GND, 1"C

LOAD CENTER 'R1GA'

- - 4.4 - - 0.5

15 20/1 EXISTING EXISTING - - 1.5 - - - 4.9 16 - - 3.4 - - -

17 20/1 EXISTING EXISTING - - 1.5 - - - 6.6 18 - - 4.1 - - 1.0

19 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 20 20/1

EXISTING

EXISTING - - 1.5 - - -

21 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 22 20/1 EXISTING EXISTING - - 1.5 - - -

23 20/1 EXISTING EXISTING - - 1.5 - - - 3.0 24 20/1 EXISTING EXISTING - - 1.5 - - -

- - 18 - - - A B C - - 22 - - 1.5

LOAD TYPE CONNECTED LOAD KVA DEMAND KVA PHASE A KVA 15 128 PHASE A AMPS

INTERIOR LTG - - PHASE B KVA 12 104 PHASE B AMPS

EXTERIOR LTG - - PHASE C KVA 14 117 PHASE C AMPS

RECEPTACLES 40 25 TOTAL CONNECTED KVA: 42

AC / HEAT PUMP - - LIGHTING FEEDER DEMAND = 125% PER 2011 NEC 210.19(A)(1) TOTAL DEMAND KVA: 27

ELECTRIC HEAT - - RECEPTACLE DEMAND LOAD PER 2011 NEC TABLE 220.44

KITCHEN: - -

MISC: 2 2 TOTAL CONNECTED AMPS: 116

25% OF LARGEST MOTOR (XXX, XX HP): - TOTAL DEMAND AMPS: 74

PANELBOARD SCHEDULE NEW PNL 'R1GA' FED FROM 'R1G'

60 AMP MLO 208 Y / 120 V PH 4 W MOUNT: SURFACE PANEL ASSEMBLY RATED: 22 KAIC

CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC A B C CCT BRKR WIRE SIZE LOAD ILTG ELTG REC MECH KIT MISC

1 20/1 (4)#12, (1)#12 GND, 3/4"C PROGRAM MNGR 103 - RECEPTS - - 1.1 - - - 1.3 2 20/1 (4)#12, (1)#12 GND, 3/4"C KITCHEN 106 - RECEPT - - 0.2 - - -

3 20/1 (4)#12, (1)#12 GND, 3/4"C ENGINEER 102 - RECEPTS - - 1.1 - - - 1.3 4 20/1 (4)#12, (1)#12 GND, 3/4"C KITCHEN 106 - RECEPT - - 0.2 - - -

5 20/1 (4)#12, (1)#12 GND, 3/4"C OPER. MNGR 101 - RECEPTS - - 0.9 - - - 1.9 6 20/1 (4)#12, (1)#12 GND, 3/4"C FRIDGE 106 - RECEPT - - 1.0 - - -

7 20/1 (4)#12, (1)#12 GND, 3/4"C ENGINEER 105 - RECEPTS - - 0.9 - - - 1.3 8 20/1 (4)#12, (1)#12 GND, 3/4"C COPIER 104 - RECEPT - - 0.4 - - -

9 20/1 (4)#12, (1)#12 GND, 3/4"C

CIRCULATION/KIT 104,106 - RECS

- - 0.5 - - - 0.9 10 20/1 (4)#12, (1)#12 GND, 3/4"C CIRCULATION 104 - RECEPT - - 0.4 - - -

11 20/1 (4)#12, (1)#12 GND, 3/4"C ADMIN ANALYST 107 - RECPTS - - 1.1 - - - 1.5 12 20/1 (4)#12, (1)#12 GND, 3/4"C COPIER 108 - RECEPT - - 0.4 - - -

13 20/1 (4)#12, (1)#12 GND, 3/4"C CONFERENCE 109 - RECEPTS - - 1.1 - - - 1.1 14 20/1 - SPARE - - - - - -

15 20/1 (4)#12, (1)#12 GND, 3/4"C

WAITING/CUST 110,125 - RECS

- - 0.5 - - - 0.5 16 20/1 - SPARE - - - - - -

17 20/1 (4)#12, (1)#12 GND, 3/4"C CUSTMR SER 125 - RECS - - 0.7 - - - 0.7 18 20/1 - SPARE - - - - - -

19 20/1 (4)#12, (1)#12 GND, 3/4"C CUSTMR SER 125 - RECS - - 0.7 - - - 0.7 20 20/1 - SPARE - - - - - -

21 20/1 (4)#12, (1)#12 GND, 3/4"C

LOBBY/HUDDLE 111,113 - RECS

- - 0.7 - - - 0.7 22 20/1 - SPARE - - - - - -

23 20/1 (4)#12, (1)#12 GND, 3/4"C AUTOMATIC DOOR OPENER - - - - - 1.0 1.0 24 20/1 - SPARE - - - - - -

25 20/1 (4)#12, (1)#12 GND, 3/4"C DOOR CONTROLS - - - - - 0.5 0.5 26 20/1 - SPARE - - - - - -

27 20/1 - SPARE - - - - - - - 28 20/1 - SPARE - - - - - -

29 20/1 - SPARE - - - - - - - 30 20/1 - SPARE - - - - - -

- - - - - - - - - - - - -

- - - - - - - - - - - - -

- - 9.4 - - 1.5 A B C - - 2.4 - - -

LOAD TYPE CONNECTED LOAD KVA DEMAND KVA PHASE A KVA 5 41 PHASE A AMPS

INTERIOR LTG - - PHASE B KVA 3 29 PHASE B AMPS

EXTERIOR LTG - - PHASE C KVA 5 42 PHASE C AMPS

RECEPTACLES 12 11 TOTAL CONNECTED KVA: 13

AC / HEAT PUMP - - TOTAL DEMAND KVA: 12

ELECTRIC HEAT - - LIGHTING FEEDER DEMAND = 125% PER 2011 NEC 210.19(A)(1)

KITCHEN: - - RECEPTACLE DEMAND LOAD PER 2011 NEC TABLE 220.44

MISC: 2 2 TOTAL CONNECTED AMPS: 37

25% OF LARGEST MOTOR (XXX, XX HP): - TOTAL DEMAND AMPS: 35

FLOOR PLAN - NEWWORK POWER

E2.01

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

PLANNORTH

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018

HUDDLE ROOM

113

CUSTOMER

SERVICE

125

OPERATIONS

MANAGER

101

ENGINEER

102

PROGRAM

MGR.

103

ENGINEER

105

ADMIN. PROJ.

ANALYST

107

CIRCULATION

104

KITCHENETTE

106

CIRCULATION

104

CONFERENCE

ROOM

109

CIRCULATION

108

WAITING

110

CIRCULATION

112

LOBBY

111

OC

OC

OC

OC OC

1/8" = 1'-0"

OC

OC

OC

OC

OCOC

OC

A AE

A

A

A AE

A

AE

A

AE

AE

A

A

AE

A AE

AAE

AE AAAE

AE

X

X

X

X

X

X

X

X

X

X

D

D

AE A

A A

A A

CE

C

B

B

B B

BB B B

B

BE

BE

B

CE

C

C C

C

C

C

C

OC

1/8" = 1'-0"

HUDDLE ROOM

113

CUSTOMER

SERVICE

125

OPERATIONS

MANAGER

101

ENGINEER

102

PROGRAM

MGR.

103

ENGINEER

105

ADMIN. PROJ.

ANALYST

107

CIRCULATION

104

KITCHENETTE

106

CIRCULATION

104

CONFERENCE

ROOM

109

CIRCULATION

108

WAITING

110

CIRCULATION

112

LOBBY

111

JSIVS78TKJSI

JSIVS78TKJSI

JSIVL1678SOJSI

JSIVL1678SOJSI

JSIVL2448ELRJSI

JSIVL2448ELRJSI

JSIVL3066RDFJSI

JSIVL3066RDFJSI

30

15

30

95

30

60

30

30

30

30

30

PLAN KEY NOTES

E.C. TO WIRE EXIT LIGHTS AND EMERGENCY LIGHTS AHEAD OF LOCAL

SWITCHING AND CONTROLS.

E.C. TO REUSE EXISTING LIGHTING CIRCUIT SERVING THIS AREA.

1

GENERAL NOTES

A. VERIFY ALL INFORMATION PRIOR TO ROUGH-IN.

B. A SITE SURVEY WAS CONDUCTED TO LOCATE ALL DEVICES AFFECTED BY THIS SCOPE

OF WORK, FIELD VERIFY ALL DEVICES AFFECTED DURING THIS SCOPE OF WORK AND

PROVIDE ALL WORK NECESSARY TO ACHIEVE A COMPLETE INSTALLATION.

C. CONTRACTOR SHALL XRAY THE EXISTING FLOOR SLAB PRIOR TO CUTTING FOR FLOOR

BOX LOCATIONS TO VERIFY THAT NO EXISTING INFRASTRUCTURE WILL BE DAMAGED.

D. CIRCUIT INFORMATION IS BASED ON EXISTING PANELBOARD DIRECTORY. FIELD VERIFY

EXISTING INFORMATION AND PROVIDE ALL CHANGES NECESSARY TO MAINTAIN

CONTINUITY TO ALL DEVICES/CONNECTIONS THAT ARE EXISTING TO REMAIN.

E. DURING THE DEMOLITION PHASE, THERE HAVE (73) 2X4 FLUORESCENT FIXTURES FOR

A TOTAL OF 5,694-WATTS REMOVED. DURING THE NEW WORK PHASE, THERE HAS BEEN

(22) 2X4S AND (29)2X2S ADDED FOR A TOTAL OF 2486-WATTS ADDED FOR A TOTAL OF

3208-WATTS REMOVED FROM EXISTING SERVICE.

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

TB3-1

1

TB3-2

1

L1C-7

1

1

1

1

1

2

2

B

OC

OC

OC

B

OCOC

OC

OC

TB3-3

TB3-4

EXISTING PNL 'R1G'

EXISTING PNL 'L1C'

OC

FLOOR PLAN - NEWWORK LIGHTING

AND SYSTEMS

E2.02

AR

CH

IT

EC

T

S

3200 N

OR

FO

LK

S

TR

EE

T, R

IC

HM

ON

D, V

A

23230

PH

ON

E (804) 794-7555 F

AX

(804)

355-5690

MO

SE

LE

Y

.C

OM

PROJECT

NO: DATE:

3/5/2018 4:15:35 P

M

CIT

Y H

AL

L R

EN

OV

AT

IO

NS

- F

IR

ST

F

LO

OR

S

UIT

E

11

5

563106

CIT

Y O

F R

IC

HM

ON

D

RIC

HM

ON

D, V

IR

GIN

IA

23219

900 E

AS

T B

RO

AD

S

TR

EE

T

REVISIONS

DATE DESCRIPTION

Lu+SmithENGINEERS

5243 HICKORY PARK DRIVE, STE CGLEN ALLEN, VA 23059

p: 804.925.2600 f: 804.925.2170www.LSEngineers.net

PLANNORTH

DAWEN LU

Lic. No. 035702

R

E

E

N

I

G

N

E

LAN

O

I

S

S

E

F

O

R

P

05/11/18

MAY 11, 2018