$5 - Stoddard · Table of Contents 1-800-342-1414 1 - 7 Engine Crankshaft Parts, Engine Lubrication, Engine Sheet Metal, Pistons, Rings, Cylinders, and Valve Train. 8 - 9 Fuel System

914Parts and Technical Reference Catalog

Classic

$5.00

Please visit www.porsche.com/classic for further information.

Appellation: Weissach.

Varietal: Porsche.

For all vintages from 1948.

Porsche Classic.Developed in Weissach. Made in Germany. The elixir of life for all aircooled

Porsche boxer engines – for optimum protection against wear and corrosion.

Available in two different grades: 20W-50 and 10W-60.

Now at your authorized Porsche dealer.

Contact us at 1-800-PORSCHE or porscheusa.com. © 2014 Porsche Cars North America, Inc. Porsche recommends seat belt usage and observance of all traffic laws at all times.

Part numbers: 00004320928 (20W-50, 1 litre), 00004320929 (20W-50, 5 litres), 00004320930 (10W-60, 1 litre), 00004320931 (10W-60, 5 litres)

140429_AZ_USA_Parade_8_5x11_RZ_EN_v2.indd 1 29.04.14 17:28

Table of Contents

1-800-342-1414

1 - 7 Engine Crankshaft Parts, Engine Lubrication, Engine Sheet Metal, Pistons,

Rings, Cylinders, and Valve Train.

8 - 9 Fuel System Fuel Pump and Carburetor Components, Gaskets, Conversion Kits,

Rebuild Kits, Air Filters, Fuel Cocks and Fuel Tank Components.

10 Heat & Exhaust Heating System Parts: Air Hoses, Vent and Defroster Covers and Heater Slides.

Exhaust System: USA and European versions, Clamps, Gaskets, Mufflers and Chrome Exhaust Tips.

11 - 12 Transmission Transmission Parts; Transaxle Mounts, Speedi Sleeves, Repair Sets,

Bearings, Differential Components, Clutches and Clutch Components.

13 - 18 Suspension Front Suspension Parts; Bushings, Grease Fittings, Tie Rods,

Steering Box Parts, and Steering Wheel Components. Rear Suspension Parts, Wheels, Hubcaps, Jacks and Accessories.

19 - 21 Brakes Brake Lines, Bridge Pipes, Wheel Cylinders, Drum Brake System Components, Master cylinders

and Disc Brake System Components.

22 - 24 Cables & Levers Pedals, Cable Housings, Brake Cables, Heater and Hood Cables,

Shift Couplers and Boots, Shift Lever Components.

25 - 34 Body Rubber Seals, Exterior Body Panels, Structural Body Parts, Door and Window Parts and Seals,

Glass, Bumpers and Parts, Exterior Trim, Emblems, Badges, Decals, Convertible Tops, Carpet Sets, Upholstery and Interior Parts.

35 - 37 Electrical Engine & Tune Up Parts, Starters, Switches, Generators, Battery and Fuse Boxes, Dashboard

and Interior items, Knobs, Windshield Wiper, Washer Parts, Front and Rear Lights and Reflec-tors, Bulbs and Fuses.

38 - 48 Other Product and Services Hardware Sets, Technical Books, Chemicals, Special Tools, Color Chart, Body and

Engine Identification Table, Ordering Policy and Warranty.

914

914

[ 1 ]

914-6 Engine

1 911.102.171.00 .............. Flywheel bolts, 6 req'd ...................................................................................................914-62 901.102.162.04 ............. Washer ...........................................................................................................................914-6 3 901.102.026.02 ............. Flywheel .........................................................................................................................914-6 999.012.014.00 ............. Dowel pin, 3 req'd ..........................................................................................................914-64 901.102.025.01 ............. Pilot bushing ..................................................................................................................914-65 901.103.172.00 ............. Connecting rod bolt, 12 req'd .........................................................................................914-66 901.103.173.00 ............. Connecting rod nut, 12 req'd ..........................................................................................914-67 911.103.132.00 .............. Connecting rod bushings, 6 req'd ..................................................................................914-68 901.103.141.00.SET ..... Connecting rod bearing set, standard ............................................................................914-6 901.103.141.50.SET ..... Connecting rod bearing set, 1st under (0.25mm) ..........................................................914-6 901.103.141.60.SET ..... Connecting rod bearing set, 2nd under (0.50mm) .........................................................914-69 999.113.057.52 .............. Crankshaft seal ..............................................................................................................914-610 901.102.147.00 ............. Woodruff key ..................................................................................................................914-611 N101.090.01 .................. Dowel pin .......................................................................................................................914-612 901.102.111.00 .............. Timing gear for number “0” ............................................................................................914-6 901.102.111.10 .............. Timing gear for number “1” ............................................................................................914-613 901.102.145.00 ............. Intermediate ring ............................................................................................................914-614 901.102.115.01 .............. Distributor drive gear ......................................................................................................914-615 901.102.148.00 ............. Lock ring ........................................................................................................................914-616 911.102.017.50 .............. V-Belt pulley ...................................................................................................................914-617 900.028.014.01 ............. Spring washer ................................................................................................................914-618 999.093.005.02 ............. Bolt .................................................................................................................................914-619 911.101.901.00 .............. Main bearing set, standard ............................................................................................914-6 911.101.901.50 .............. Main bearing set, 1st under (0.25mm) ...........................................................................914-6 911-101-901-55 ............. Main bearing set, 2nd under (50mm) .............................................................................914-6Note: The #8 main bearing is not included with the above sets and must be ordered separately20 901.101.138.03 ............. #8 Main bearing .............................................................................................................914-6 901.101.138.53 ............. #8 Main bearing, 1st under (0.25mm) ............................................................................914-6 901.101.138.58 ............. #8 Main bearing, 2nd under (0.50mm) ...........................................................................914-621 900.012.061.00 ............. Dowel pin .......................................................................................................................914-622 999.113.290.41 .............. Crankshaft seal ..............................................................................................................914-623 900.174.068.40 ............. O-Ring ............................................................................................................................914-6

Engine

12

19

3

9

4

5 6

8

7

16

10

11

13

23

2021

22

17

18

15

14

12

914

1-800-342-1414 [ 2 ]

Engine

Reno 1-800-438-8119

1

4

5

7

6

14

13

8

13

11

10912

15

15

1819

17

16 12

11

20

21

3

2

1

1914-6 Engine

1 911.606.230.00 .............. Oil pressure sender ........................................................................................................914-62 901.107.751.00 ............. Oil thermostat ....................................................................................................914-6 to 1971 930.107.765.00 ............. Oil thermostat ............................................................................................914-6 1972 and up3 999.707.314.40 ............. Sealing ring ....................................................................................................................914-64 901.101.172.03 ............. Case studs, 24 req'd ......................................................................................................914-6 930.101.170.02 ............. Dilivar case studs, 24 req'd ............................................................................................914-6Note: Dilivar studs were not standard on the 914-6, but are much stronger than the originals and can be used in their place.

5 999.070.004.02 ............. Cap nut, 13 req'd............................................................................................................914-66 901.101.161.02 ............. Washer, 12 req'd ............................................................................................................914-67 999.701.006.40 ............. O-Ring, 12 req'd .............................................................................................................914-68 999.061.034..02 ............ Stud, engine to transmission, 2 req'd .............................................................................914-69 999.064.026.02 ............. Screw, 2 req'd ................................................................................................................914-610 900.123.106.30 ............. Sealing ring, 2 req'd .......................................................................................................914-611 901.107.531.00 ............. Pressure spring, 2 req'd .................................................................................................914-612 901.107.512.01 ............. Piston, 2 req'd ................................................................................................................914-613 999.707.112.40 .............. O-Ring, 8 req'd ...............................................................................................................914-614 901.107.351.01 ............. Oil return tubes, 4 req'd..................................................................................................914-6 930.107.040.01 ............. Factory collapsible oil return tubes, 4 req'd....................................................................914-6 SIC.107.351.00 ............. Aftermarket collapsible oil return tubes, 4 req'd .............................................................914-6

15 930.101.391.01 ............. Sump gasket, 2 req'd .....................................................................................................914-616 901.101.380.01 ............. Oil strainer ......................................................................................................................914-617 SIC.101.286.00 ............. Sump cover ....................................................................................................................914-618 900.123.106.30 ............. Sealing Ring ...................................................................................................................914-619 911.641.632.00 .............. Drain plug .......................................................................................................................914-620 901.641.632.00 ............. Temperature sensor .......................................................................................................914-621 900.123.007.30 ............. Seal ................................................................................................................................914-622 901.100.902.03 ............. Engine gasket set ..........................................................................................................914-6

Note: Collapsible oil return tubes allow for tube replacement without removing the cylinder hears. The heads must be removed in order to use the original return tubes.

914

[ 3 ]

Engine

Valve Train

914-6 Engine Parts

1 930.105.197.05 ............. Gasket, 2 req'd ...............................................................................................................914-62 999.701.124.40 ............. O-Ring, 2 req'd ..............................................................................................................914-6 3 930.105.196.00 ............. Cover, 2 eq'd ..................................................................................................................914-64 900.028.008.01 ............. Spring washer, 6 req'd ...................................................................................................914-65 900.075.341.02 ............. Bolt, 6 req'd ....................................................................................................................914-66 901.105.562.00 ............. Thrust washer,2 req'd.....................................................................................................914-67 901.105.561.00 ............. Shim ...............................................................................................................................914-68 901.105.583.01 ............. Flange chain wheel, 2 req'd ...........................................................................................914-69 900.243.001.00 ............. Dowel pin, 2 req'd ..........................................................................................................914-610 911.105.529.00 .............. Timing chain,original endless version, 2 req'd ...............................................................914-6 911.105.529.50 .............. Timing chain, removable link version, 2 req'd ................................................................914-6 901.105.530.00 ............. Master link for removable link timing chain, 2 req'd .......................................................914-611 911.105.222.06 .............. Black chain rails, 5 req'd ................................................................................................914-612 911.105.222.05 .............. Brown chain rails, 1 req'd ...............................................................................................914-613 901.105.546.02 ............. Chain wheel 2, 2 req'd ...................................................................................................914-614 900.028.021.02 ............. Spring washer, 2 req'd ...................................................................................................914-615 901.105.172.00 ............. Camshaft nut, 2 req'd .....................................................................................................914-616 900.041.026.01 ............. Lock ring ........................................................................................................................914-617 900.041.025.01 ............. Lock ring, 2 req'd............................................................................................................914-618 930.105.013.01 ............. Intermediate shaft with “0” gear and sprocket ................................................................914-6 930.105.136.11 .............. Intermediate shaft with “1” gear and sprocket ................................................................914-619 930.105.136.00 ............. “0” Gear only ..................................................................................................................914-6 930.105.136.01 ............. “1” Gear only ..................................................................................................................914-620 901.105.125.04 ............. Chain sprocket only, 2 req'd ...........................................................................................914-621 993.101.135.00 ............. Bearings, small plain, 2 req'd .........................................................................................914-622 993.101.137.00 ............. Bearings, large flanged, 2 req'd .....................................................................................914-6

11

11

11

10

22

20

17

1918

21

16

1

2

4

5

3

6

7

8

9

10

11

13

15

14

12

11

17

914

1-800-342-1414 [ 4 ]

EngineValve Train / Pistons

914-6 Rocker and Shafts1 930.105.043.05 ............. Rocker arm, 12 req'd........................................ 914-62 999.034.005.00 ............. Hex nut, 12 req'd .............................................. 914-6 3 901.105.370.02 ............. Adjusting screw, 12 req'd ................................. 914-64 901.105.376.03 ............. Nut, 12 req'd..................................................... 914-65 901.105.342.04 ............. Rocker shaft, 12 req'd ...................................... 914-66 901.105.344.03 ............. Bushing, 12 req'd ............................................. 914-67 999.067.008.00 ............. Socket head bolt .............................................. 914-6

7

65

4

1

23

1 2 3 4

5 6 7 7 8 9

Oil Pressure Fed Tensioner KitIntroduced on the 1984 Carrera, this system eliminates the one weakness of the 911 / 914-6 motor: seal falure in the tensioners resulting in severe damage to the valve train. Oil pressure fed tentioners utilize hydraulic tension produced by the oil system and have no seals.Our kit includes two “058” series tensioners, five oil lines (one specially modified), two timing chain covers, all hardware and gaskets. For pre 1980 engines we recommend use of the stronger bushed sprocket supports, listed below, although the kit is supplied with spacers to use your original supports.

SIC.105.058.00 Oil fed tentioner kit, 1 kit per car

Chain Sprocket Supports, Late StyleOur oil fed tensioner kit includes spacer bushings for use of the original non-bushed sprocket supports. However, we recommend use of these stronger bushed supports which were introduced in 1980 and do not require the spacer busings.930.105.509.00 Left sprocket support930.105.510.00 Right sprocket support

OE Tensioner Repair KitTo rebuild “049” and “053” non-pressure hydraulic tensioners. 1 kit required per tensioner.

911.105.901.01

Timing Cover Gasket KitIncludes nyloc nuts, hardware and gaskets, 1 required per car

SIC.105.191.00

Valve Covers and Gaskets901.105.115.03 .......... Upper valve cover ................................ 914-6SIC.105.115.03 .......... Upper valve cover ................................ 914-6 930.105.116.00 .......... Lower valve cover, late turbo style....... 914-6 SIC.105.116.05 .......... Lower valve cover ................................ 914-6SIC.105.195.02.......... Valve adjust gasket kit, includes hardware

914-6 Valves1 901.105.408.50 ............. Exhaust valves, 6 req'd ..................................................................................................914-62 901.105.407.00 ............. Intake valves, 6 req'd .....................................................................................................914-6 3 SIC.104.321.50 ............. Valve guides, intake and exhaust, standard 12 req;d ....................................................914-64 964.104.111.07 .............. Valve stem seals, 12 req'd .............................................................................................914-65 930.105.461.00 ............. Shim ...............................................................................................................................914-66 901.105.463.00 ............. Ring, 12 req'd .................................................................................................................914-67 901.105.901.51 ............. Inner and outter valve spring set, 12 req'd .....................................................................914-68 901.105.421.03 ............. Concave washer, 12 req'd..............................................................................................914-69 901.105.417.00 ............. Valve keepers, 24 req'd ..................................................................................................914-6

914

[ 5 ]

Engine

914-4 Crankshaft

914-4 Engine Parts1 N014.336.B ................... Flywheel bolt, 5 req'd ...................................................................................................914-All2 021.105.275 .................. Special washer at flywheel ...........................................................................................914-All 3 022.105.273.A ............... Flywheel (NLA) ............................................................................................................914-All4 N013.197.1 .................... Flywheel dowel pin, 3 req'd ..........................................................................................914-All5 111.105.311 ................... Sealing ring ..................................................................................................................914-All 6 111.105.313.A ................ Pilot bearing .................................................................................................................914-All 7 021.105.279 .................. Sealing ring ..................................................................................................................914-All 8 029.105.245.B ............... Crankshaft seal ............................................................................................................914-All 9 021.105.281 .................. Shim 0.30mm ...............................................................................................................914-All 021.105.283 .................. Shim 0.32mm ...............................................................................................................914-All 021.105.285 .................. Shim 0.34mm ...............................................................................................................914-All 021.105.287 .................. Shim 0.36mm ...............................................................................................................914-All 021.105.291 .................. Shim 0.24mm ...............................................................................................................914-All 10 021.198.481.A ............... Main bearing set, standard ..........................................................................................914-All 021.198.483.A ............... Main bearing set, 1st under (0.25mm) .........................................................................914-All 021.198.483.A ............... Main bearing set, 2nd under (0.50mm) ........................................................................914-All 11 022.105.159 .................. Spacer sleve ................................................................................................................914-All 12 N.012.708.2 ................... Woodruff key ................................................................................................................914-All 13 N012.709.1 .................... Woodruff key for pulley ................................................................................................914-All 14 021.105.209.A ............... Gear (NLA) ...................................................................................................................914-All 15 113.105.219 ................... Intermediate ring ..........................................................................................................914-All 16 901.102.115.01 .............. Bronze distributor gear .................................................................................................914-All 17 111.105.227 ................... Lock ring for distributor drive gear ...............................................................................914-All 18 021.105.247.A ............... Crankshaft seal, at pulley end ......................................................................................914-All

914-4 Rebuild Gasket Sets 021.198.009.B ............... Engine gasket set .......................................................................................................914-1.7 029.198.009 .................. Engine gasket set .......................................................................................................914-1.8 039.198.009 .................. Engine gasket set .......................................................................................................914-2.0

1

2

3

5

46

7

8

10

119

10

1019

20

22

24

23

15

17

10

16

1410

1213

18

21

914

1-800-342-1414 [ 6 ]

Engine

Reno 1-800-438-8119

914-4 Camshaft

914-4 Valves1 021.198.541 .................. Camshaft bearing set .....................................................................................................914-42 021.109.601 .................. Intake valve .................................................................................................................914-1.7 3 021.109.612.A ............... Exhaust valve ..............................................................................................................914-1.7 021.109.612 .................. Exhaust valve ..............................................................................................................914-1.8 039.109.611.L ................ Exhaust valve ..............................................................................................................914-2.0 4 039.101.421 .................. Valve guide exhaust ....................................................................................................914-2.0 5 039.101.403 .................. Valve guide intake .......................................................................................................914-2.0 021.101.403.A ............... Valve guide intake .................................................................................................914-1.7/1.8 021.101.417.A ............... Valve guide, exhaust .............................................................................................914-1.7/1.8 6 021.109.335.C ............... Push rod tube ............................................................................................................914-4 all7 021.109.345.A ............... Push rod tube seal ....................................................................................................... 914 all 113.101.157.C ............... Camshaft engine case plug ......................................................................................... 914 all

914-4 Engine Carrier9 039.199.231 .................. Engine mount, on crossbar, 2 req'd, side shifter transmission only ......................914-1.8/2.0 SIC.199.231 .................. Engine mount, on crossbar, 2 req'd, side shifter transmission only ......................914-1.8/2.0

914-6 Engine Carrier 914.375.049.00 ............. Engine mount, front ........................................................................................................914-6

1

914-4 Valves 914-4 Engine Carrier

2 3

7 65 4

9

8

10

11

17

16

14

2612

13

152418

23

2120

19

2225

1312

914

[ 7 ]

Engine

Maintenance Parts

914-6 Maintneance Parts901.107.203.09.................... Mahle oil filter .................................................................................................................914-6901.108.955.11 .................... Air filter ...........................................................................................................................914-6 133.133.511 ......................... Fuel filter ........................................................................................................................914-6SIC.101.391.01.................... Silicone gasket for oil sump plate, set of 2 .....................................................................914-6 900.123.106.30.................... Seal ring for oil deain plug .............................................................................................914-6 911.602.933.00 .................... Bosch distributor cap .....................................................................................................914-6 SIC.602.933.00.................... Bosch distributor cap .....................................................................................................914-6 616.602.226.02.................... Ignition point set, one piece, for cars with aluminum distributors ...................................914-6 901.602.953.00.................... Marelli distributor cap .....................................................................................................914-6 SIC.602.965.00.................... Distributor cap clip, short ...............................................................................................914-6 SIC.609.061.00.................... Ignition wire set, 90 degree connectors .........................................................................914-6 SIC.609.591.00.................... Ignition spark plug wire holder .......................................................................................914-6 901.609.309.00.................... Spark plug wire connector .............................................................................................914-6 999.659.034.40.................... Spark plug wire cap .......................................................................................................914-6 999.170.128.90.................... Bosch W3DPO spark plug .............................................................................................914-6 914-4 Mainteance Parts021.115.351.A ...................... Oil filter ............................................................................................................914-1.7/1.8/2.0022.129.620......................... Air filter, round, wet .....................................................................................................914-1.7 021.129.620......................... Air filter, square, dry ..............................................................................................914-1.8/2.0133.133.511 ......................... Fuel filter ...................................................................................................................914-4 All 021.198.031.B ..................... Oil strainer gasket set ...............................................................................................914-4 All 021.101.481......................... Valve cover gasket ....................................................................................................914-4 All SIC.101.481......................... Valve cover gasket ....................................................................................................914-4 All SIC.115.487 ......................... Oil tower gasket ........................................................................................................914-4 All 059.998.051.B ..................... Distributor points set .................................................................................................914-4 All 311.906.041.A ...................... Cylinder head temperature sensor ............................................................................914-4 All 999.170.156.90.................... Spark plug, Bosch WR7CC, 4 req'd ..........................................................................914-4 All

914

1-800-342-1414 [ 8 ]

1

2

7

8 96

5

4

3

Fuel & Exhaust

Carburetor & Fuel Injection

914-4 Fuel System1 944.606.103.00 ............. Auxitiary air regulator ..................................................................................................914-1.82 022.906.035 .................. Pressure regulator ......................................................................................................914-1.8 3 022.133.241B ................ Connecting hose, 4 req'd ............................................................................................914-1.7 022.133.241 .................. Connecting hose, 4 req'd ......................................................................................914-1.8/2.04 022.906.301 .................. Air flow sensor .....................................................................914-1.8 to engine # EC0037551 473.906.301 .................. Air flow sensor .................................................................914-1.8 from engine # EC0037552 5 022.129.683 .................. Air flow sensor gasket .................................................................................................914-1.8 6 311.906.041.A ............... Cylinder head temperature sensor ..................................................................914-1.7/1.8/2.0 7 022.906.031.A ............... Fuel injector, 4 req'd ....................................................................................................914-1.7 022.906.031.C ............... Fuel injector, 4 req'd ....................................................................................................914-1.8 039.906.031.A ............... Fuel injector, 4 req'd ....................................................................................................914-2.0 8 311.133.263 ................... Fuel injector seal set .................................................................................................914-4 all

Miscellaneouos 914 4/6 Fuel System Parts 901.741.801.00 ............. Fuel level sending unit ................................................................................................. 914 all SIC.741.801.00 ............. Fuel level sending unit ................................................................................................. 914 all 477.919.133 .................. Fuel level sending unit gasket ...................................................................................... 914 all 911.608.107.03 .............. Fuel pump ......................................................................................................................914-69 SIC.906.091. ................. Fuel pump electric, late 914, 1.8-2.0 .......................................................................914 75-76 10 NLA.108.005.01 ............ Fuel pump, 12 volt, 2.5 to 4.0 psi for carbureted 914-4 or 914-6 ................................. 914 all11 039.129.707 .................. Intale manifold gasket at head ...................................................................................914 2.0

914-6 Carburetor Gaskets1 911.110.391.00 .............. Gasket, 6 req'd ........................................................914-62 901.108.218.00 ............. Gasket, 2 req'd ........................................................914-63 901.108.398.01 ............. Gasket, 6 req'd ........................................................914-64 901.108.391.04 ............. Gasket for intake manifold, 12 req'd .......................914-65 901.108.131.00 ............. Intermediate flange, 6 req'd ....................................914-6

914-6 Carburetor Rebuild KitSIC.100.948.00.................... Weber 40IDA3C, one kit per carburetor ..................914-6

914-6 Carburetor Linkage Ball Sockets900.169.010.02.................... Left handed thread ball sockets, 2 req'd .................914-6900.169.001.02.................... Right handed thread ball sockets, 4 req'd ...............914-6900.076.029.02.................... Left hand thread lock nut, 2 req'd ...........................914-6N011.005.14 ........................ Right hand thread lock nut, 2 req'd .........................914-6

21

3

54

4

910

914

[ 9 ]

Fuel & Exhaust

Exhaust Systems

3

1

3

3

3

4

2

3

3

5

7

6

9

3

11

3 10

5

4

914-4 Muffler1 021.251.053.C ............... Muffler with tailpipe and hardware ........................................................................914 1.7/1.82 039.251.067.A.SIC ........ Muffler with hardware ..................................................................................................914 2.0 311.101.463 ................... Locking exhaust nut, 8mm ........................................................................................... 914 all 3 025.251.261 .................. Exhaust gasket heat exchanger to muffler ...........................................................914- 1.7/1.84 039.256.251 .................. Exhaust gasket heat exchanger to muffler ..................................................................914 2.0 025.251.235 .................. Gasket tailpipe to muffler ......................................................................................914 1.7/1.8 5 NLA.043.037.00 ............ Wurth Sabesto exhaust sealant paste ......................................................................... 914 all 6 NLA.095.006.00 ............ High temperature exhaust paint, correct Factory gray color ........................................ 914 all NLA.095.006.01 ............ High temperature exhaust paint, correct Factory gray color, quart .............................. 914 all

Note: Our Hi Temperature exhaust paint is avaliable in quarts and spray cans, it is an extreemly durable industrial coating with proper preparation will not discolor or flake, can be baked in an oven or heat cured on the car.

914-6 Exhaust1 022.256.205.A ......... Heater valve left ............................. 914-62 022.256.206.A ......... Heater valve right ........................... 914-6 3 999.512.349.01 ....... Hose clamp 50-70mm .................... 914-64 SIC.111.011.11 ........ Muffler ............................................ 914-65 901.111.245.01 ........ Exhaust tip ..................................... 914-66 SIC.211.005.00 ........ Heat exchanger set ........................ 914-6 7 901.111.193.00 ........ Muffler to heat exchanger gasket .. 914-6 8 999.085.001.02 ....... Heat exchanger nut ....................... 914-6 9 930.111.191.13 ........ Heat exchanger gasket .................. 914-6

6

5

3 4

914

1-800-342-1414 [ 10 ]

Fuel & Exhaust

Heat Exchangers

Reno 1-800-438-8119

914-4 Exhaust1 022.256.091.B ............... Heat exchanger, left, stainless steel SSI ...............................................................914 1.7/1.82 022.256.092.B ............... Heat exchanger, right, stainless steel SSI ............................................................914 1.7/1.8 039.256.091 .................. Heat exchanger, left stainless steel SSI ......................................................................914 2.0 039.256.092 .................. Heat exchanger, right, stainless steel SSI ..................................................................914 2.0 022.256.091.F ............... Heat exchanger, left, steel factory part .................................................................914 1.7/1.8 022.256.092.F ............... Heat exchanger, right, steel factory part ...............................................................914.1.7/1.8 025.251.261. ................. Exhaust gasket, heat exchanger to muffler ........................................................914-4 1.7/1.8 3 021.256.321.D ............... Heat exchanger duct lid/cover ..................................................................................... 914 all PCG.256.331.GRV ........ Heat exchanger “J” pipe, Left ....................................................................................... 914 all PCG.256.332.GRV ........ Heat exchanger “J” pipe, right ...................................................................................... 914 all 4 022.256.205.A ............... Heat control box, left .............................................................................................914 1.7/1.8 5 022.256.206.A ............... Heat control box, right ...........................................................................................914 1.7/1.8 6 311.129.777 ................... Threaded swivel pin, connects cable to heater control box, 2 req'd ......................... 914-4 all 900.075.105.02 ............. Bolt for threaded swivel pin, 2 req'd ..........................................................................914-4 all 7 SIC.572.194.00 ............. Heater hose, 60mm, black sold by the foot .................................................................. 914 all N.014.684.1 ................... Exhaust stud, 8 req'd ................................................................................................914-4 all 8 311.101.463 ................... Locking exhaust nut, 8mm ........................................................................................914-4 all 9 021.256.251.A ............... Exhaust gasket, heat exchanger to head ..............................................................914 1.7/1.8 10 039.256.251 .................. Exhaust gasket, heat exchanger to head ....................................................................914 2.0 11 443.253.115.B ............... Exhaust gasket, heat exchanger to muffler and crossover pipe, 4 req'd ............914 1975-76 12 NLA.043.037.00 ............ Wurth exhaust sealant paste ....................................................................................... 914 all

7

109876

9

1

2

4

5

8

12

3

914

[ 11 ]

12

11

10

9

87

1

2

6

5

3

Transmission Parts

13

1415

Transmission

Clutch and Transmission

1 999.611.920.20 .............. Transmission ground strap.........................................................................................1970-762 914.375.025.00 ............. Transmission mount ...................................................................................................1970-76 3 901.318.243.00 ............. Speedometer drive bushing, complete (NLA) ............................................................1970-764 911.318.029.00 .............. Speedometer angle drive ...........................................................................................1970-76 5 999.053.025.00 ............. Transmission main shaft bearing ...............................................................................1970-76 6 999.052.016.0A ............. Transmission pinion shaft bearing .............................................................................1970-76 7 901.301.392.12 ............. Transmission case gasket..........................................................................................1970-76 8 901.301.191.21 ............. Transmission case gasket, 1mm ................................................................................1970-76 901.301.191.22 ............. Transmission case gasket, 1.5mm.............................................................................1970-76 901.301.191.23 ............. Transmission case gasket, 2.0mm.............................................................................1970-76 9 914.613.491.00 ............. Protective rubber boot for reverse switch ..................................................................1970-76 10 914.613.541.02 ............. Reverse light switch ...................................................................................................1970-76 11 999.113.183.40 .............. Side cover seal, 2 req'd..............................................................................................1970-76 914.301.391.01 ............. Gasket on bottom of tailpiece ....................................................................................1970-76 12 113.311.113.B ................ Mainshaft seal at imput shaft .....................................................................................1970-76 914.300.901.00 ............. Transmission gasket set complete .............................................................................1970-76 914.318.261.01 ............. Sealing washer forspeedometer drive 15mm x 20mm ...............................................1970-76 13 999.113.036.50 .............. Oil seal for speedometer drive ...................................................................................1970-76 14 999.064.019.OC ............ Transmission screw plug ............................................................................................1970-76 15 113.301.185.A ............... Rubber O-Ring ...........................................................................................................1970-76

4

23

18

9 8

7

2

6

5

4 10

1111

101970 - 1976 Clutch Parts1 901.116.087.11 ........ Guide tube ........................1970-762 NLA.027.014.01 ...... Spring washer, 6mm .........1970-763 900.076.010.02 ....... 6mm nut ............................1970-764 901.116.077.01 ........ Fastening plate .................1970-765 901.116.741.01 ........ Transmission bushing .......1970-76 6 901.116.712.00 ........ Fork ...................................1970-76 7 900.067.009.02 ....... Socket head scew, 6mm ...1970-76 8 901.116.825.11 ........ Guide piece .......................1970-76 9 901.116.081.11 ........ Release bearing ................1970-76 10 901.116.001.01 ........ Pressure plate ...................1970-76 11 914.116.011.05 ........ Clutch disc ........................1970-76

914

1-800-342-1414 [ 12 ]

Transmission

Transmission Internal Components

Transmission Gears and Shafts1 911.302.316.06 .............. Brake band, 1st-5th for 901 transmission .................................................................... 914 all 2 911.302.301.13 .............. Synchro ring, 1st-5th for 901 and 915 transmission .................................................... 914 all 3 SIC.302.241.06 ............. Synchro hub ................................................................................................................. 914 all4 999.038.001.00 ............. Tab lock washer ........................................................................................................... 914 all 5 930.302.325.00 ............. Thrust block energizer ................................................................................................. 914 all 6 911.302.226.00 .............. Shift sleeve first and reverse for 901/902 transmissions ............................................. 914 all 7 999.110.008.00 .............. Flywheel-end mainshaft bearing for 901 transmissions ............................................... 914 all 8 999.110.012.01 .............. Rear pinion shaft bearing ............................................................................................. 914 all 9 999.053.025.00 ............. Main shaft bearing ....................................................................................................... 914 all 999.059.008.00 ............. Differential carrier bearing ............................................................................................ 914 all 999.062.008.02 ............. Stud M8 X 25mm ......................................................................................................... 914 all 999.062.002.02 ............. Stud M6 X 15mm ......................................................................................................... 914 all 901.332.285.01 ............. Lock tab for ring gear bolts .......................................................................................... 914 all 901.332.561.11 .............. Thrust washer for limited slip differential ...................................................................... 914 all SIC.300.990.85 ............. Speedi sleeve for 901 transmission mainshaft ............................................................ 914 all 999.201.470.00 ............. Needle cage 1st-5th .................................................................................................... 914 all

1

2

3

4 6

5

3

7 35

53

2 2

94

8

1 4 2

2

6

5

2

2

7

35 2

2

3

5

1

Pinion Shaft

Main Shaft

914

[ 13 ]

8

7

6

4

5

2

31

Suspension

Front Suspension

1 901.341.159.00 ............. Front control arm protetive bracket ............................................................................1970-76 2 900.067.063.03 ............. Cheese head screw ...................................................................................................1970-76 3 900.027.015.02 ............. Washer lock ring ........................................................................................................1970-764 914.341.422.01 ............. Control arm rubber bushing, front ..............................................................................1970-76 SIC.341.422.00 ............. Control arm rubber bushing, front ..............................................................................1970-76 SIC.341.421.02 ............. Control arm rubber bushing, front, 4 piece set ...........................................................1970-76 SIC.711.120.00 .............. Control arm bushing, Poly Graphite, front ..................................................................1970-76 5 900.040.008.01 ............. Control arm plug ........................................................................................................1970-76 901.341.163.00 ............. Control arm plug, rubber ............................................................................................1970-76 6 911.341.901.01 .............. Front lower control arm, left, OE ................................................................................1970-76 911.341.902.01 .............. Front lower control arm, right, OE ..............................................................................1970-76 SIC.341.901.00 ............. Front lower control arm, left .......................................................................................1970-76 SIC.341.902.00 ............. Front lower control arm, right .....................................................................................1970-767 911.341.161.00 .............. Underbody suspension protection plate .....................................................................1970-76 8 SIC.341.165.00 ............. Protection plate seal set .............................................................................................1970-76 9 901.341.475.00 ............. Control arm adjusting gasket .....................................................................................1970-76 10 901.341.033.00 ............. Adjusting lever, front suspension ...............................................................................1970-76 11 911.341.115.02 .............. Front torsion bar adjusting screw bolt ........................................................................1970-76 900.042.005.01 ............. Torsion bar lock ring on control arm ...........................................................................1970-76

8

11

10

96

45

2

3

1

1 901.343.703.04 ...........Stabilizer bar, 16mm2 901.343.792.02 ...........Rubber bushing, 2 req’d 3 901.343.754.01 ...........Mounting plate, 2 req’d ..4 901.343.763.00 ...........Guide plate, 4 req’d .......5 901.343.713.01 ...........Lever, 2 req’d .................6 901.343.737.00 ...........Spacer tube, 4 req’d ......7 901.343.783.00 ...........Rubber bushing, 4 req’d 8 901.343.076.03 ...........Shackle, 2 req'd

914

1-800-342-1414 [ 14 ]

SuspensionSteering Parts

Reno 1-800-438-8119

1 914.347.010.06 ............. Steering rack complete, reproduction ........................................................................1970-762 901.347.308.00 ............. Inner boot spring clamp .............................................................................................1970-763 901.347.309.00 ............. Outter boot spring clamp ............................................................................................1970-76 4 901.347.191.02 ............. Steering rack bellow ...................................................................................................1970-76 930.347.191.02 ............. Steering rack bellow, for Turbo tie rods ......................................................................1970-765 900.027.016.02 ............. Split washer ...............................................................................................................1970-76 6 N.010.253.7 ................... Hex head bolt, 10mm x 22mm ...................................................................................1970-76 900.075.460.01 ............. Hex head bolt, 10mm x 35mm ...................................................................................1970-76 7 911.347.031.00 .............. Tie rod assembly, Lemfoerder ....................................................................................1970-76 911.347.031.01 .............. Tie rod assembly, Porsche Classic ............................................................................1970-76 930.347.031.01 ............. Tie rod assembly, Porsche .........................................................................................1970-76 SIC.347.930.00 ............. Turbo tie rod kit, complete..........................................................................................1970-76 8 901.347.315.03 ............. Tie rod fork .................................................................................................................1970-76 9 N.011.210.1 ................... Castle nut for tie rod ...................................................................................................1970-76 10 900.021.013.00 ............. Split pin for tie rod ......................................................................................................1970-76 11 914.347.057.00 ............. Rack bushing, for tie rod end .....................................................................................1970-76 12 911.347.322.04 .............. Outer tie rod end, 2 req'd ...........................................................................................1970-76 930.347.322.00 ............. Turbo tie rod end, 2 req'd ...........................................................................................1970-76 13 SIC.347.930.00 ............. Turbo tie rod kit ..........................................................................................................1970-76 930.347.025.01 ............. Steering column universal joint ..................................................................................1970-76 14 901.347.201.02 ............. Steering coupler .........................................................................................................1970-76 901.347.248.00 ............. Steering coupler lock plate .........................................................................................1970-76

Miscellaneous Upper Steering

3

8

7

5

6 42

12

9 10

3

24

901.347.823.01 ............. Rubber horn cuff ........................................................................................................1970-76 914.347.831.00 ............. Horn contact button pin ..............................................................................................1970-76 914.347.711.00 .............. Upper steering shaft bearing ......................................................................................1970-76 911.347.771.02 .............. Upper steering shaft bearing ......................................................................................1970-76 N.012.239.1 ................... Steering wheel lock nut washer, 19mm x 33mm ........................................................1970-76 901.347.753.00 ............. Steering rcolumn sheer bolt .......................................................................................1970-76 900.027.016.02 ............. Split washer ...............................................................................................................1970-76 N.010.253.7 ................... Hex head bolt, 10mm x 22mm ...................................................................................1970-76 900.052.007.00 ............. Ball bearing for pinion shaft in steering rack ..............................................................1970-76 930.347.025.01 ............. Steering column universal joint, 2 req'd .....................................................................1970-76 15 914.347.057.00 ............. Bushing for tie rod at steering rack ............................................................................1970-76

1

13

14

15

901.347.082.10Mahagony Wood Steering Wheel 400mm VDM

Leather Wrapped Steering Wheel 400mm VDM

901.347.081.10 Hockey puck horn button complete, reproduction, 914-6 GT

901.347.803.00

914

[ 15 ]

Suspension

Front Suspension

74

5

1

6

4

2

57

9

8

15

19

18

1716

14

13

1210

11

24 24

27

21

22

23

3

2526

28

914

1-800-342-1414 [ 16 ]

SuspensionFront Suspension

Front Struts1 911.501.934.00 .............. Camber adjusting plate ..............................................................................................1970-762 911.501.933.00 .............. Strut clamp .................................................................................................................1970-76 3 911.341.018-00 ............. Front upper strut mount .............................................................................................1970-76 4 900.067.063.03 ............. Cheese head screw, 6 req'd.......................................................................................1970-76 5 999.523.103.01 ............. Lock washer, 6 req'd ..................................................................................................1970-76 6 900.038.002.01 ............. Shock top lock plate, 2 req'd ......................................................................................1970-76 7 901.341.629.00 ............. Strut plate support washer .........................................................................................1970-76 SIC.864.110.77 .............. Koni sport adjustable strut insert, all ..........................................................................1970-76 SIC.P36.112 .................. Bilstein strut insert for Boge strut assemblies ............................................................1970-76 8 911.341.804.01 .............. Strut insert retaining cap ............................................................................................1970-76 9 901.343.301.00 ............. Front shock strut buffer ..............................................................................................1970-76 10 999.701.084.50 ............. Sealing ring ................................................................................................................1970-76 11 901.341.623.00 ............. Wheel bearing spacer ring .........................................................................................1970-76 901.341.661.00 ............. Wheel bearing spacer ring .........................................................................................1970-76 12 477.405.641 .................. Front wheel bearing seal, inner ..................................................................................1970-76 SIC.405.641 .................. Front wheel bearing seal, inner ..................................................................................1970-76 13 999.059.098.00 ............. Roller type inner wheel bearing, 914-6 ......................................................................1970-72 14 999.059.065.00 ............. Roller type outter wheel bearing, 914-6 .....................................................................1970-72 15 901.341.065.10 ............. Front wheel hub, Porsche Classic part, 914-6 ...........................................................1970-72 16 911.341.663.00 .............. Wheel bearing thrust washer .....................................................................................1970-76 17 SIC.405.670 .................. Front axle nut, right hand, 914-4 ................................................................................1970-76 SIC.405.669 .................. Front axle nut, left hand, 914-4 ..................................................................................1970-76 18 999.119.001.0B ............. Allen head bolt for wheel bearing clamping nut .........................................................1970-7619 914.341.684.00 ............. Front wheel bearing dust cap .....................................................................................1970-76 20 901.341.049.04 ............. Ball joint, early, to chassis number 4722919032 ........................................................1970-73 911.341.049.05 .............. Ball joint, late, from chassis number 4722919033 .....................................................1973-76 21 901.341.425.01 ............. Grooved ball joint retaning nut ...................................................................................1970-76 22 901.341.426.00 ............. Locking plate ..............................................................................................................1970-76 23 N.012.521.1 ................... Split pin, 2x15 ............................................................................................................1970-76 24 911.341.119.07 .............. Ball joint wedge pin, late, from chassis number 4722919033 ....................................1973-76 25 900.089.006.02 ............. Lock washer, 8mm x 16mm, for wedge pin ................................................................1973-76 26 999.084.019.02 ............. Wedge pin hex nut .....................................................................................................1973-76 27 900.075.111.08 .............. Ball joint bolt, early, to chassis number 4722919032 .................................................1970-73 28 999.523.103.01 ............. Ball joint bolt lock washer ...........................................................................................1970-73

1 901.343.703.04 ....... Front sway bar, 15mm ................... 1973-762 901.343.792.01 ....... Anti roll bar body mount ................. 1973-76 3 901.343.754.01 ....... Anti roll bar body mounting plate ... 1973-76 4 900.027.015.02 ....... Lock washer ................................... 1973-76 5 900.075.083.02 ....... Bolt, 8mm x 25mm ......................... 1973-76 6 901.343.713.01 ....... Anti roll bar lever ............................ 1973-76 7 900.076.025.02 ....... Hex nut, 6 req'd .............................. 1973-76 8 901.343.736.00 ....... Guide plate, 4 req'd ........................ 1973-76 9 901.343.076.03 ....... Anti roll bar drop link ...................... 1973-76 10 901.343.737.00 ....... Drop link bushing, 4 req'd .............. 1973-76 11 901.343.783.00 ....... Drop link bushing ........................... 1973-76 SIC.343.783.00 ....... Drop link bushing ........................... 1973-76

1

2

3

45

6

7 4

4

4

7

7

8

8

1011

11

Note: Factory anti roll bars were an option beginning in 1973, cars built prior to that can be retrofitted with the correct factory parts.

914

[ 17 ]

1

2

3

4

5

6

7

8

9

10

9

Rear Axle and Sway Bar

Rear Stabilizer Bar Parts (option on 1973 - 1976)

1 914.501.532.71 ....... Reinforcement plate ............ 914 all2 914.501.259.11 ........ Mounting plate ...........914 up to 753 901.333.793.04 ....... Roll bar bushing .................. 914 all4 901.333.753.01 ....... Mounting bracket ................ 914 all 5 900.027.015.02 ....... Lock washer ........................ 914 all 6 900.075.087.02 ....... Bolt ...................................... 914 all 7 914.333.055.06 ....... Sway bar ............................. 914 all 8 914.333.057.00 ....... Drop link .............................. 914 all 9 901.343.782.00 ........ Drop link bushing ..................914 all 10 914.333.565.01 ........ Pin .........................................914 all

8

9

1

3

2

4 7

65

Rear Axle Parts

Suspension

1 914.332.009.03 ............. Half shaft complete, CVs,boots and shaft, Porsche Classic part ..............................914-4 all2 914.332.237.00 ............. CV joint gasket (green) .............................................................................................914-4 all 914.332.237.01 ............. CV joint gasket, paper, gray ......................................................................................914-4 all 3 999.095.019.00 ............. Roll pin for CV joint ...................................................................................................... 914 all4 999.053.035.00 ............. Rear wheel bearing ...................................................................................................... 914 all 5 999.025.046.01 ............. Washer under castle nut .............................................................................................. 914 all 6 901.332.806.01 ............. Castle nut for rear axle ................................................................................................. 914 all 7 900.021.024.00 ............. Cotter pin, 4mm X 40mm ............................................................................................. 914 all 8 901.332.293.10 ............. CV joint axle boot, 4 req'd ............................................................................................ 914 all 901.332.293.11 .............. CV joint axle boot, 4 req'd ............................................................................................ 914 all 9 914.332.228.01 ............. CV joint “protection cap”, attaches to boot, 4 req'd ...................................................... 914 all SIC.999.647.00 ............. Lubro Moly CV joint grease, 4 req'd ............................................................................. 914 all 10 999.523.102.02 ............. Lock washer, 16 req'd ....................................................................................................914-6 11 900.067.073.02 ............. Cheese head screw, 16 req'd....................................................................................... 914 all 12 999.041.016.01 ............. Lock ring, 4 req'd............................................................................................................914-6 113.501.327 ................... Lock ring, 4 req'd............................................................................................................914-4

10

11

12

914

1-800-342-1414 [ 18 ]

Rear Suspension

Reno 1-800-438-8119

Rear Shocks

1 SIC.559.281.10 ............. Rear shock top boot ..................................................................................................... 914 all 900.910.042.02 ............. Hex nut ......................................................................................................................... 914 all2 914.333.513.01.SIC ...... Dampening bushing for rear strut ................................................................................ 914 all 914.333.513.01.SIC ...... Top strut bushing, rear ................................................................................................. 914 all 3 SIC.824.110.50 .............. Koni sport shock, rear .................................................................................................. 914 all SIC.B46.179.00 ............. Bilstein heavy duty shock, rear .................................................................................... 914 all 4 914.333.053.01 ............. Shock bump rubber, 2 req'd ......................................................................................... 914 all

1

2

3

7

8

14

15

13

16

17

12

1110

4

Suspension

914

[ 19 ]

13

14

15

18

17

21

20

22

23

19

25

12

10

911

16

8

6

6

5

56

Front Braking System 914-4

Brakes

Front Brake Lines8 901.355.632.01 ............. Brake hose front .........................................................................................................1970-76 695.351.681.90 ............. Brake hose front .........................................................................................................1970-76 914.355.531.00 ............. Fitting, ATE .................................................................................................................1970-76 901.355.531.00 ............. Hollow screw ..............................................................................................................1970-76 N013.808.3 .................... Washer .......................................................................................................................1970-76 904.355.902.00 ............. Washer .......................................................................................................................1970-766 113.611.715.A ................ Brake hose retaining bracket .....................................................................................1970-76 803.611.715 ................... Brake line retaining spring .........................................................................................1970-76 5 914.355.691.00 ............. Brake line hose piece .................................................................................................1970-76

Note: The original 17mm master cylinder is no longer avaliable, for a direct fit and improved pedal feel use the currently avaliable 19.5 ATE replacement listed here.

1 901.355.012.00 ............. Brake master cylinder, 19.5mm, ATE Germany .........................................................1970-76 911.355.012.02 .............. Brake master cylinder, dual circuit,19.5mm, ATE Germany .......................................1970-76 901.355.930.00 ............. Master cylinder rebuild kit, 19.5mm only ....................................................................1970-76 901.613.115.00 .............. Warning light switch, 2 pole .......................................................................................1970-76 914.613.116.00 .............. Warning light switch, single pole ................................................................................1970-76 901.355.936.00 ............. Inlet line washer, 8mm x 10mm .................................................................................1970-76 15 911.355.013.13 .............. Brake fluid reservoir w/cap .........................................................................................1970-76 13 477.611.361 ................... Reservior cap w/gasket ..............................................................................................1970-76 211.611.381.B ............... Brake fluid reservoir strainer ......................................................................................1970-76 21 111.957.861 ................... Grommet, 2 req'd .......................................................................................................1970-7622 901.355.929.00 ............. Master cylinder inlet grommet ....................................................................................1970-76 23 901.355.936.00 ............. Washers, 2 req'd ........................................................................................................1970-76 19 PCG.355.161.00 ........... Connecting line reservoir to master cylinder ..............................................................1970-76 20 PCG.355.163.00 ........... Connecting line reservoir to master cylinder ..............................................................1970-76 17 999.181.021.50 ............. Brake fluid connecting hose, blue, sold by the meter ................................................1970-76 18 PCG.512.055.02 ........... Brake reservoir hose clamps, 2 req'd.........................................................................1970-76

000.044.305.01

914

1-800-342-1414 [ 20 ]

26

2

5

4 615

2

54

5

5

119

8

10

13

22

16

1

22 13

1222

7

21

17

19

18

17

14

7

2

Rear Braking System

Rear Brake Lines1 901.355.631.01 ............. Brake hose rear .........................................................................................................1970-76 901.355.631.02 ............. Brake hose rear, OE ..................................................................................................1970-76 2 901.355.615.01 ............. Brake line elbow fitting ...............................................................................................1970-76 3 NLA.355.667.00 ............ Brake line 3 way connector ........................................................................................1970-76 4 914.355.651.00 ............. Brake line grommet, 2 req'd .......................................................................................1970-76 5 914.355.652.00 ............. Brake line grommet clamp, 2 req'd ............................................................................1970-76 6 914.355.614.01.SIC ...... Brake line in tunnel ....................................................................................................1970-76 7 914.355.636.01.SIC ...... Brake connecting line, right ........................................................................................1970-72 8 914.355.635.01 ............. Brake connecting line, left ..........................................................................................1970-72 914.355.531.00 ............. Fitting .........................................................................................................................1970-76 901.355.531.00 ............. Hollow screw ..............................................................................................................1970-76 N013.808.3 .................... Washer .......................................................................................................................1970-76 904.355.902.00 ............. Washer .......................................................................................................................1970-76 6 914.355.661.00 ............. Brake hose connection piece .....................................................................................1970-7622 113.611.715.A ................ Brake hose retaining bracket .....................................................................................1970-76 25 803.611.715 ................... Brake line retaining spring .........................................................................................1970-76 5 914.355.691.00 ............. Brake line protection hose piece ................................................................................1970-76

Items 8 through 16 are for 914-6/1.7/2.0 up to chassis no. 47429157518 914.355.668.00 ............. Hollow screw ..................................................................................................................914-69 904.355.902.00 ............. Washer ...........................................................................................................................914-6 10 N013.803,3 .................... Washer ...........................................................................................................................914-611 914.355.669.00 ............. 2 way connector .............................................................................................................914-612 914.355.636.01 ............. Brake connecting line, right .......................................................................................... 914 all 13 914.355.635.01 ............. Brake connecting line, left ............................................................................................ 914 all

Items 17 through 21 are for 914 1.8/2.0 from Chassis no 474291575217 999.507.235.40 ............. Brake line clip .............................................................................................................1974-76 0 803-611-715 .................. Brake line retaining spring .........................................................................................1974-7618 914.355.635.02 ............. Brake connecting line, left ..........................................................................................1974-76 19 914.355.636.03 ............. Brake connecting line, right ........................................................................................1974-76 13 914.355.635.01 ............. Brake connecting line, left ..........................................................................................1974-76 14 14.355.636.01 ............... Brake connecting line, right ........................................................................................1974-76

Brakes

000.044.305.01

914

[ 21 ]

1 2 3

1 901.355.012.00 ............. Brake master cylinder, 19.5mm, ATE Germany .........................................................1970-76 911.355.012.02 .............. Brake master cylinder, dual circuit,19.5mm, ATE Germany .......................................1970-76 901.355.930.00 ............. Master cylinder rebuild kit, 19.5mm only ....................................................................1970-76 901.613.115.00 .............. Warning light switch, 2 pole .......................................................................................1970-76 914.613.116.00 .............. Warning light switch, single pole ................................................................................1970-76 901.355.936.00 ............. Inlet line washer, 8mm x 10mm .................................................................................1970-76 911.355.013.13 .............. Brake fluid reservoir w/cap .........................................................................................1970-76 477.611.361 ................... Reservior cap w/gasket ..............................................................................................1970-76 211.611.381..B .............. Brake fluid reservoir strainer ......................................................................................1970-76 901.355.929.00 ............. Master cylinder inlet grommet ....................................................................................1970-76 PCG.355.161.00 ........... Connecting line reservoir to master cylinder ..............................................................1970-76 PCG.355.163.00 ........... Connecting line reservoir to master cylinder ..............................................................1970-76 999.181.021.50 ............. Brake fluid connecting hose, sold by the meter .........................................................1970-76

Note: Originally all 4 cylinder 914's were fitted with a 17mm master cylinder, only the 914-6 was fitted with the 19mm 911 size master cylinder, now all that is avaliable is 19mm which is a common upgrade to improve pedal feel and performance.

2 914.351.425.00.SET ..... Brake caliper set front, early w/one bleeder, restored to as new ...............................1970-72 914.615.107.00.SET ..... Brake caliper set front, late w/two bleeders, restored to as new ................................1972-76 4 411.698.471 ................... Brake caliper rebuild kit, front, 4 cylinder, 2 req'd ......................................................1970-76 3 914.352.423.00E.SET ... Brake caliper set rear, early w/one bleeder, restored to as new ................................1970-72 4 914.352.423.00L.SET ... Brake caliper set rear, late w/two bleeders, restored to as new .................................1972-76 914.352.000.99 ............. Brake caliper rebuild kit, rear, 4 cylinder, 2 req'd .......................................................1970-76 SIC.352.914.60 ............. Rear brake pad adjusting screw, 8mm/10mm, 4 cylinder ..........................................1970-76 5 914.352.000.00 ............. Plug for rear caliper pad adjusting screw ...................................................................1970-76 901.351.913.14 ............. Brake pad retaining pin ..............................................................................................1970-76 6 SIC.352.950.OE ............ Brake pads, M-caliper, OE ceramic compound, D31, front ........................................1970-76 SIC.352.950.HP ............ Brake pads, M-caliper, High Performance compound, D31, front ..............................1970-76 SIC.351.912.OE ............ Brake pads, L-caliper, OE ceramic compound, D30, rear ..........................................1970-76 SIC.351.912.HP ............ Brake pads, L-caliper, High Performance compound, D30, rear ...............................1970-76

Brake System Components

Brakes

4

5 6 7 8

Note: Our brake pads are made to our specifications by HAWK Performance, all our backing plates are NuCap backing plates usually reserved for motorsports applications, 2 specific compounds, a contemporary low dust ceramic, and a HP version that improves performance while maintains a user friendly level of noise and dust.

000.044.305.01

914

1-800-342-1414 [ 22 ]

2

1

15

612

11

7

109

17

5126

64

12

7

6

5

21

20

00

16

16

17/18

1314

20

5

1 914.423.210.00 ............. Clutch and brake pedal pad .......................................................................................1970-762 SIC.551.671.00 ............. Pedal stop mount, gold zinc plated ............................................................................1970-76 3 SIC.551.671.20 ............. Nylon pedal stop ........................................................................................................1970-764 901.423.010.01 ............. Accelerator pedal .......................................................................................................1970-76 SIC.423.010.00 ............. Accelerator pedal .......................................................................................................1970-76 914.423.277.01 ............. Accelerator pedal push rod ........................................................................................1970-76 5 NLA.169.001.02 ............ Ball socket, right hand thread, 914-4, 2 req'd, 914-6, 4 req'd ....................................1970-76 6 900.076.092.01 ............. Clutch cable adjusting nut ..........................................................................................1970-76 7 914.423.401.05 ............. Clutch cable, 914-4 ....................................................................................................1970-76 8 914.423.401.02 ............. Clutch cable, 914-6 ....................................................................................................1970-72 9 914.423.922.02 ............. Clutch cable boot .......................................................................................................1970-76 10 914.423.283.00 ............. Clutch cable stop piece ..............................................................................................1970-76 11 999.166.001.02 ............. Clutch cable clevis .....................................................................................................1970-76 12 SIC.423.067.02 ............. Accelerator cable, 914-4 ............................................................................................1970-76 914.423.066.02 ............. Accelerator cable, 914-6 ............................................................................................1970-72 13 311.129.777 ................... Threaded swivel pin ...................................................................................................1970-76 14 900.075.105.02 ............. Bolt for pin, 5mm x 10mm ..........................................................................................1970-76 15 SIC.424.075.01 ............. Heater cable ...............................................................................................................1970-74 16 113.711.691 ................... Heater cable boots .....................................................................................................1970-7617 914.424.551.01 ............. Emergency brake cable, left ......................................................................................1970-76 18 914.424.552.01 ............. Emergency brake cable, right ....................................................................................1970-76 19 914.423.593.00 ............. Emergency cable rubber boot ....................................................................................1970-7620 NLA.423.020.3M ........... Transmission bell crank repair kit, 914-6 ...................................................................1970-72 21 SIC.423.341.01 ............. Pedal assembly bushing kit, bronze bushings, pins, lock nut and washers ...............1970-76 22 901.423.343.00 ............. Plastic bushing for clutch pedal shaft .........................................................................1970-76 23 914.424.053.01.SIC ...... Hand brake handle, complete, non-bending, German production .............................1970-76

Pedal Assembly and Cables

Reno 1-800-438-8119

Cables &

Levers

3

914

[ 23 ]

Shifter Components

Front Shifter Parts

1 SIC.424.014.00 ............. Shift knob, 5 speed, dog leg pattern, requires crush sleeve ........................................ 914 all 901.424.014.00 ............. Shift knob, 5 speed, dog leg pattern, Porsche Classic part ......................................... 914 all 914.424.018.00 ............. Shift knob, 5 speed, dog leg pattern, Porsche Classic part ......................................... 914 all2 999.532.003.00 ............. Shift knob crush sleeve ................................................................................................ 914 all 3 914.424.016.03 ............. Gearshift lever, chrome ............................................................................................914 to 724 914.424.901.00 ............. Rubber shifter boot ...................................................................................................... 914 all 5 901.424.132.00 ............. Thrust spring guide ...................................................................................................... 914 all 6 914.424.131.00 ............. Shifter console thrust spring ........................................................................................ 914 all 7 901.424.135.00 ............. Shifting guide ............................................................................................................... 914 all 8 901.424.017.00 ............. Shifter stop plate .......................................................................................................... 914 all 9 N.012.435.1 ................... Circlip ........................................................................................................................... 914 all 10 901.424.113.00 .............. Shifter spring, 2 req'd ................................................................................................... 914 all 11 914.424.512.00 ............. Shift rod lever ball bushing .......................................................................................914 to 72 12 SIC.424.139.00 ............. Shifter ball socket .....................................................................................................914 to 72 911.424.139.01 .............. Shifter ball socket .....................................................................................................914 to 72 13 914.424.224.00 ............. Shift rod bushing, 3 req'd .........................................................................................914 to 72 14 914.424.214.00 ............. Shift rod clamp at transmission ................................................................................914 to 72 15 914.424.224.03 ............. Shift rod bushing ....................................................................................................914- 72 on 16 901.424.229.00 ............. Shift coupler conical screw .......................................................................................... 914 all 17 911.424.223.03 .............. Shift coupler bushing, 2 req'd..................................................................................914-72 on 18 914.424.792.01 ............. Heater control knob, red plastic .....................................................................................914-6

Cables &

Levers

1 1

3

4

10

15

17

16

56

11

8

6

2 2

4

510

812

14

16

17

13

14

1970 - 1972 1973 - 1976

914

1-800-342-1414 [ 24 ]

Shifter Components

1

4

23

16

17

1210

11

3

15 5

9

1423

13

Rear Shifter Parts

1 914.424.512.00 ............. Shift rod lever ball bushing, 2 req'd .......................................................................914-4 to 732 914.424.224.03 ............. Shifter bushing at firewall ...............................................................................................914-6 3 914.424.224.02 ............. Shifter bushing at rear of transmission ..........................................................................914-64 SIC.424.139.00 ............. Shift rod ball socket ......................................................................................................914-4 t5 914.424.501.01.SIC ...... Shift rod cover for side shifter transmission .....................................................914-4 73 to 76 7 914.424.501.00 ............. Shift rod cover and boot at firewall ......................................................................914 70 to 72 8 999.113.183.40 .............. Side cover seal ............................................................................................................ 914 all 9 901.424.229.00 ............. Shift rod coupler screw ...........................................................................................914 to 76 10 901.741.291.00 ............. Shifter rod boot at rear .......................................................................................914-4/6 to 72 11 914.424.224.00 ............. Shift rod guide bushing ......................................................................................914-4/6 to 72 12 999.512.348.02 ............. Hose clamp .......................................................................................................914-4/6 to 72 13 999.513.003.40 ............. Black tie wrap clamp .............................................................................................914-4 to 76 14 911.424.139.00 .............. Shift rod ball socket bushing .................................................................................914-4 to 76 15 999.512.103.02 ............. Strap for shifter rod cover ........................................................................................914 to 76 16 914.424.224.02 ............. Shift rod bushing ......................................................................................................914 to 76 17 914.424.501.00 ............. Shift linkage cover and boot at firewall .................................................................914/6 to 72

Cables &

Levers

914-6

914-4 1973-1976

914-4 1970-1972 914-4/6 1970-1972

914

[ 25 ]

Exterior Body Parts

Body

11

25

26

23

22

29

14

15

18

12

1

4

2

7

8

13

19

31

32

3433

35

28

27

3839

37

30

26

54

914

1-800-342-1414 [ 26 ]

Structural Body Parts

Reno 1-800-438-8119

Structural Body Parts1 SIC.501.939.00 ............. Floor pan half, left ......................................................................................................1970-76 SIC.501.940.00 ............. Floor pan half, right ....................................................................................................1970-76 2 SIC.501.939.10 ............. Rear floor pan quarter, left .........................................................................................1970-76 SIC.501.940.10 ............. Rear floor pan quarter, right .......................................................................................1970-76 3 914.501.937.10 ............. Pedal support bracket ................................................................................................1970-76 4 914.501.073.10 ............. Battery tray support brace ..........................................................................................1970-76 5 SIC.501.587.10 ............. Battery tray .................................................................................................................1970-76 6 914.611.233.10 .............. Clamp for battery .......................................................................................................1970-76 7 SIC.501.013.00 ............. Longitudinal frame rail stiffening panel, left, welds over exsisting structure ..............1970-76 SIC.501.014.00 ............. Longitudinal frame rail stiffening panel, right, welds over exsisting structure ............1970-76 8 SIC.501.151.10 ............. Jack support plate and jack tube ...............................................................................1970-76 SIC.501.354.00 ............. Sill triangle support ....................................................................................................1970-76 10 914.501.943.00 ............. Seat mount reinforcement ..........................................................................................1970-76 11 SIC.501.435.10 ............. Engine tray, right side, under battery tray ..................................................................1970-76 SIC.501.435.12 ............. Engine tray, left side ...................................................................................................1970-76 12 914.503.943.10 ............. Sail panel repair piece, left .........................................................................................1970-76 914.503.944.10 ............. Sail panel repair piece, right ......................................................................................1970-76 13 SIC.503.905.00 ............. Lockpost, left ..............................................................................................................1970-76 SIC.503.906.00 ............. Lockpost, right ............................................................................................................1970-76 151.837.035.SIC ........... Latch plate with threaded nuts, 2 req'd ......................................................................1970-76 914.503.390.SIC ........... Door catch reinforcement, right or left ........................................................................1970-76 SIC.501.348.00 ............. Steel jacking donut, front, 2 req'd...............................................................................1970-76 SIC.501.041.10 ............. Steel jacking donut, rear, 2 req'd................................................................................1970-76 14 914.501.013.10 ............. Inner rocker panel, left ...............................................................................................1970-76 914.501.014.10 ............. Inner rocker panel, right .............................................................................................1970-76 15 914.501.089.10 ............. Door threshold sill, left, with 2 support triangles ........................................................1970-76 914.501.090.10 ............. Door threshold sill, right, with 2 support triangles ......................................................1970-76 16 914.501.109.10 ............. Floor crossmember panel ..........................................................................................1970-76 17 914.501.109.10L ........... Floor crossmember panel, left half .............................................................................1970-76 18 914.501.109.10R ........... Floor crossmember panel, right half ..........................................................................1970-76 19 914.507.041.10L ........... Rear floor jack point, left, includes jack cup ...............................................................1970-76 914.507.042.10R ........... Rear floor jack point, right, includes jack cup .............................................................1970-76 20 914.501.937.11 .............. Front trunk floor pan ...................................................................................................1970-76 21 914.501.937.12 ............. Front trunk floor repair panel, for aftermarket A/C removal ........................................1970-76 22 914.501.000.00 ............. Front tow hook ...........................................................................................................1970-76 914.501.000.00 ............. Spare tire hold down bracket .....................................................................................1970-76 914.501.057.00 ............. Front suspension A-Arm mount .................................................................................1970-76 914.507.041.SIC ........... Front trunk pan reinforcement corner, left ..................................................................1970-76 914.507.042.SIC ........... Front trunk pan reinforcement corner, right ................................................................1970-76 23 914.501.083.20 ............. Rear trunk floor pan, fits 70-74, with modification 75-76 ............................................1970-76 24 914.503.065.11 .............. Rear cross panel ........................................................................................................1970-74 25 914.501.119.14 .............. Outer firewall, rear wall, full piece, 73-76, holes for side shifter mount ......................1973-76 914.501.643.15L ........... Inner firewall, left lower 7.5 inches .............................................................................1970-76 914.501.644.15R ........... Inner firewall, right lower 7.5 inches ...........................................................................1970-76 26 SIC.503.125.10 ............. Outer rocker panel cover, steel, left ...........................................................................1970-76 SIC.503.126.10 ............. Outer rocker panel cover, steel, right .........................................................................1970-76 27 914.559.267.10 ............. Jack port hole plug, plastic .........................................................................................1970-76 28 914.559.163.10S ........... Floor pan air deflector flap pair ..................................................................................1973-76 29 SIC.504.117.10 .............. Engine compartment seal set ...................................................................................... 914 all 30 999.702.091.50.SIC ...... Engine compartment drain seal, 2 req'd ...................................................................914-4 all

Body

914

[ 27 ]

Nam

e

Sheet Metal

12

10

14

9

16

5

1513

1

3

2

5 6

7 6

914

1-800-342-1414 [ 28 ]

Sheet MetalN

ame

1

2

3

56

7

9

810

11

Structural Body Parts

1 914.501.531.10.SIC ...... Towing lug ..................................................................................................................1970-76 2 914.501.938.11.SIC ....... Front floor pan ............................................................................................................1970-76 3 914.501.938.11.AC ........ Front floor pan, AC repair panel .................................................................................1970-764 914.507.041.10.SIC ...... Corner piece, pan reinforcement piece, left ...............................................................1970-76 914.507.042.10.SIC ...... Corner piece, pan reinforcement piece, right .............................................................1970-76 5 914.501.109.10.SIC ...... Seat crossmember complete, one piece ....................................................................1970-766 914.501.109.10.L.SIC ... Seat crossmember, left ..............................................................................................1970-76 7 914.501.109.10.R.SIC ... Seat crossmember, right ............................................................................................1970-76 8 914.501.643.10.L.SIC ... Rear bulkhead, lower, left ..........................................................................................1970-76 9 914.501.643.10.R.SIC ... Rear bulkhead, lower, right ........................................................................................1970-76 914.501.119.10.SIC ....... Outer bulkhead/firewall ..............................................................................................1970-72 914.501.119.14.SIC ....... Outer bulkhead/firewall ..............................................................................................1973-76 914.501.944.21.SIC ...... Inner wheelhouse, lower right ....................................................................................1970-76 10 914.501.083.20.SIC ...... Rear trunk floor pan, will fit 75-76 with modification ...................................................1970-76 914.501.083.21.SIC ...... Rear trunk floor reinforcement ...................................................................................1970-76 11 914.501.436.11.SIC ....... Inner longitudinal drivers compartment, left ...............................................................1970-76 12 914.501.075.10.SIC ...... Emergency brake handle pivot ..................................................................................1970-76 914.501.434.11.SIC ....... Inner longitudinal drivers compartment, right .............................................................1970-76 13 914.501.076.11.SIC ....... E-Brake cable guide at floor pan ................................................................................1970-76 14 914.503.065.11.SIC ....... Rear tail panel ............................................................................................................1970-74 15 914.503.390.3DC.SIC ... Door striker reinforcement plate, left or right ..............................................................1970-76 16 914.501.944.21.SIC ...... Inner right frame reinforcement piece, at suspension pick up point ...........................1970-76 17 914.501.057.00 ............. Front control arm mount .............................................................................................1970-76 18 914.501.000.00 ............. Spare tire hold down ..................................................................................................1970-76

914

[ 29 ]

Bumpers

Body

1

Front Bumpers Rear Bumpers

6

9

10

7

2

5

6

15

16

17

149

11

12

11

13

14

Emblems 914.559.287.11 .............. 914 Black plastic, Porsche Classic part ...................................................................914 1974 914.559.459.10 ............. 1.8 Black plastic, Porsche Classic part ....................................................................914 1974 914.559.120.11 .............. 2.0 Black plastic, Porsche Classic part ....................................................................914 1974 999.591.120.01 ............. Speed nut for emblem fastening .................................................................................. 914 all

914

1-800-342-1414 [ 30 ]

Bumpers Valances and Trim

Front Bumpers

1 914.503.023.10.SIC ...... Front bumper top .....................................................................................................914 to 74 2 914.505.027.10.SIC ...... Bumper mount dogbone, set, front ..........................................................................914 to 74 900.187.018.02 ............. Spoiler or front valance mounting screw ...................................................................... 914 all 999.151.026.02 ............. 5mm X 24mm yellow zinc washer for front and rear bumper mount ........................914 to 743 914.559.236.10 ............. Fog light grill, right, chrome ......................................................................................914 to 74 SIC.559.236.10 ............. Fog light grill, right, chrome reproduction .................................................................914 to 74 4 914.559.235.10 ............. Fog light grill, left, chrome ........................................................................................914 to 74 SIC.559.235.10 ............. Fog light grill, left, chrome reproduction ...................................................................914 to 745 911.701.053.00 .............. License plate bracket ...............................................................................................914 to 74

Rear Bumpers

6 914.503.027.10.SIC ...... Rear bumper top ......................................................................................................914 to 742 914.505.027.10.SIC ...... Bumper mount dogbone, set, rear ...........................................................................914 to 74 7 914.631.601.00 ............. Rear license light, 2 req'd.........................................................................................914 to 748 911.631.620.04 .............. Rear license light, 2 req'd........................................................................................914 75-76 911.631.608.01 .............. Rear license light gasket, 2 req'd ............................................................................914 75-765 911.701.053.00 .............. License plate bracket, rear .......................................................................................914 to 74

Body

2 5 3 4 7 8

9 10 15 16 17 18

Door Parts

914.531.061.10.SET ..... Door handle set ............................................................................................................ 914 all9 914.531.906.00 ............. Door handle, right, Porsche Classic part ..................................................................... 914 all 10 914.531.905.00 ............. Door handle, left, Porsche Classic part ........................................................................ 914 all 11 SIC.531.601.00 ............. Door handle gasket set ................................................................................................ 914 all 12 SIC.531.900.00 ............. Door handle repair piece .............................................................................................. 914 all13 SIC.531.601.10 ............. Door handle gasket, large, 2 req'd ............................................................................... 914 all 14 SIC.531.603.10 ............. Door handle gasket, small, 2 req'd............................................................................... 914 all SIC.531.609.00 ............. Door handle lock seal .................................................................................................. 914 all 914.531.903.11 .............. Key blank, red .............................................................................................................. 914 all 914.531.903.10 ............. Key blank, black ........................................................................................................... 914 all 15 914.542.307.10 ............. Early window roller set .............................................................................................914 to 72 16 SIC.531.037.10 ............. Door check repair kit, 2 req'd ....................................................................................... 914 all 17 914.731.039.10 ............. Side view mirror, left, Porsche classic part .................................................................. 914 all 18 914.731.039.10.SIC ...... Side view mirror, left, made in Germany ...................................................................... 914 all

Reno 1-800-438-8119

914

[ 31 ]

Rubber Seals and Windshield Components

Body

1

3

24

6

9

16

17 1915

20

25

13

23

58

2

7

64

6

3

10

11

10

5

Rubber Seals

Windshield and Trim

1 914.541.101.10 ....... Windshield, clear,OE ........1970-762 914.541.213.10 ....... Trim strip, left ....................1970-763 914.541.214.10 ....... Trim strip, right ..................1970-764 914.541.215.10 ....... Trim strip, bottom ..............1970-765 SIC.541.219.10 ....... Connector clip ...................1970-76 914.541.219.11 ........ Connector clip,OE .............1970-76 6 914.541.217.11 ........ Corner trim piece, 2req'd ..1970-76 7 914.541.907.10 ....... Windshield spacer ............1970-76 8 914.541.921.11 ........ Windshield trim clip ...........1970.76 914.541.213.99.set . Moulding set complete, includes, . spacers, plastic molding clips, corners, connector piece, fits all .................................................................1970-76

8

7

9

914

1-800-342-1414 [ 32 ]

Rubber Seals

Rubber Seals

1 914.511.901.10 .............. Front hood seal, all ....................................................................................................1970-762 914.563.039.10 ............. Roof seal on windshield frame, all, OE ......................................................................1970-76 3 914.552.263.10.SIC ...... Seal at bottom of windshield, inside, all .....................................................................1970-764 914.563.319.10 ............. Front top seal, inside, all, OE .....................................................................................1970-76 SIC.563.319.10 ............. Front top seal, inside, all ............................................................................................1970-76 5 914.542.325.10 ............. Vent window seal, left, all ...........................................................................................1970-76 914.542.326.10 ............. Vent window seal, right, all .........................................................................................1970-76 6 914.542.017.02.SET ..... Vent window cap seal set ...........................................................................................1970-767 914.531.185.10 ............. Top to side glass seal at top of window, left, all .........................................................1970-76 914.531.186.10 ............. Top to side glass seal at top of window, right, all .......................................................1970-76 8 914.531.939.10 ............. Furry strips against door glass, all, 2 req'd ................................................................1970-76 9 914.531.873.10 ............. Seal against glass (scraper seal) left .........................................................................1974-76 914.531.874.10 ............. Seal against glass (scraper seal) right .......................................................................1974-76 914.531.951.10 ............. Seal against glass (scraper seal), early, 2 req'd, all 914-6 ........................................1970-73 10 914.531.143.10 ............. Vertical seal against glass, left, all .............................................................................1970-76 914.531.144.10 ............. Vertical seal against glass, lright, all ..........................................................................1970-76 11 914.531.939.10 ............. Door glass furry strip, 2 req'd .....................................................................................1970-76 12 914.531.821.10 ............. Door seal inner, left, OE manufactuer ........................................................................1970-76 914.531.822.10 ............. Door seal inner, right, OE manufactuer ......................................................................1970-76 13 914.531.813.10 ............. Door seal outer, left, OE manufactuer ........................................................................1970-76 914.531.814.10 ............. Door seal outer, right, OE manufactuer .....................................................................1970-76 14 914.542.161.12 ............. Door glass window channel, front, 2 req'd .................................................................1973-76 SIC.542.161.12 ............. Door glass window channel, front, 2 req'd .................................................................1973-76 15 914.563.077.11 .............. Seal, roof to roll bar ....................................................................................................1970-76 914.563.077.11.SIC ....... Seal, roof to roll bar ....................................................................................................1970-76 16 914.512.317.10 ............. Rear seal for luggage compartment ...........................................................................1970-76 17 914.504.111.10 .............. Engine grill edging .....................................................................................................1970-76

Body

Targa Roll Bar Covering and Trim

1 SIC.559.260.10 ............. Targa bar vinyl, 3 pieces, correct pin point texture .....................................................1970-76 2 914.559.017.10 ............. Targa top cover trim plate, left, Porsche Classic part ................................................1970-76 3 914.559.018.10 ............. Targa top cover trim plate, right, Porsche Classic part ..............................................1970-76 4 914.631.949.10.SIC ...... Sail panel lower aluminum trim, left, Porsche Classic part ........................................1970-76 5 914.631.950.10.SIC ...... Sail panel lower aluminum trim, right Porsche Classic part .......................................1970-76 6 999.591.326.01 ............. Sail panel lower trim clip, 8 req'd per car ...................................................................1970-76 7 914.559.101.10 ............. Sail panel rear trim, left, Porsche Classsic part .........................................................1970-76 914.559.102.10 ............. Sail panel rear trim, right, Porsche Classsic part .......................................................1970-76 8 914.559.103.10 ............. Sail panel center trim .................................................................................................1970-76

Engine Lid Script

1 901.559.301.22“PORSCHE”script,silver..........1974-762901.559.301.23“PORSCHE”script,gold...........1970-73 999.591.423.03Speednut,14req'd..................1970-76

1

2

914

[ 33 ]

Interior Carpet and Trim

Trunk Carpet SetsNote: Trunk carpet sets were originally perlon, but we offer them in the Velour as an upgrade, in all cases made to order.

SIC.551.914.13.PER ........... Perlon front trunk carpet set . 914 all SIC.551.914.14.PER ........... Perlon rear trunk carpet set . 914 all SIC.551.914.13.800............. Velour front trunk carpet set . 914 all SIC.551.914.14.800............. Velour rear trunk carpet set .. 914 all

Body

2

Front

Rear

1

Note: 70-71seatcoversanddoorpanelsuseplainvinylinserts,72-74seatcoversanddoorpanelsuserectangularbasketweaveinserts,75-76seatcoversanddoorsuseGermansquarebasketweaveinserts.

Interior Panels

1 914.555.017.11 .............. Door panel, left complete, black, Porsche Classic part ................................................ 914 all 914.555.118.11 .............. Door panel, right complete, right, Porsche Classic part ............................................... 914 all 914.555.017.11.SIC ....... Door panel, left complete, black, basket weave .............................................. 914-4 1972-74 914.555.018.11.SIC ....... Door panel, right complete, black, basket weave ........................................... 914-4 1972-74 2 914.555.061.12 ............. Rear wall complete, black, Porsche Classic part ...............................................914 1972-76 3 914.552.031.12.SIC ...... Dash top as original, for 72- on glove box, but will fit 70/71 ........................................ 914 all 4 914.521.251.10.SIC ...... Dash top vinyl and padding .......................................................................................... 914 all

Interior Vinyl Sets

1 SIC.521.914.01 ............. Seat cover set, full left, bottom right ...............................................................................70-71 SIC.521.914.02 ............. Seat cover, 2 req'd .........................................................................................................72-74 SIC.521.914.03 ............. Seat cover, 2 req'd .........................................................................................................75-76 SIC.555.914.01 ............. Door panels, pair, smooth ..............................................................................................70-71 SIC.555.914.02 ............. Door panels, pair, basket weave ....................................................................................72-74 SIC.555.914.03 ............. Door panels, pair, square weave ...................................................................................75-76 SIC.555.914.04 ............. Rear panel, fixed passenger seat ..................................................................................70-71 SIC.555.914.05 ............. Rear panel, moveable passenger seat ..........................................................................72-76 SIC.555.914.06 ............. Floor vinyl kit, 8 pieces ...................................................................................................70-76

3

4

Nam

e914

1-800-342-1414 [ 34 ]

Name

Interior Carpet Sets

Note: We offer 914 carpet sets in both the original perlon and velour (similar to 1967-1973 911S carpet). Both are available in charcoal (black) only. interior carpet sets include all interior pieces shown above.

SIC.551.914.10.PER ..... Perlon carpet set, 10 piece ........................................................................................1970-72 SIC.551.914.10.800 ...... Velour carpet set, 10 piece ........................................................................................1970-72 SIC.551.914.11.PER ..... Perlon carpet set, 10 piece ........................................................................................1973-76 SIC.551.914.11.800 ....... Velour carpet set, 10 piece ........................................................................................1973-76

Carpet Cement

SIC.999.096.05 Stoddard carpet cement in quart can good for brush or spray application.

NLA.556.010.00 Super 77 spray adhesive, covers large areas quickly.

Seatbelt re-webbingWe offer a seat belt re-webbing and inertia reel inspection and ser-vice. The standard webbing color is black but for an additional fee other colors (32) are avaliable. Your belts will look and function as new. SIC.803.126.09.RWB

Interior Components

1 SIC.551.137.10 ............. Threshold set, 4 piece, anodized aluminum includes clear rivets ..............................1970-722 SIC.551.137.10.BLK ..... Threshold set, 4 piece, anodized aluminum, black, includes black rivets ..................1974-76 3 SIC.731.043.12 ............. Sun visor set, Passenger side mirror, includes pivots ................................................1970-764 SIC.521.251.10.SIC ...... Center console seat tray ............................................................................................1970-76 5 911.456.001.SET ........... “PRESS” seat belt decal car set ................................................................................1970-76 6 914.552.233.10.01C ...... Interior trim plug, black, to cover pillar pad screws ....................................................1970-76 7 999.591.311.40 .............. Door panel clip insert .................................................................................................1970-76 8 999.591.102.12 ............. Chrome cone protection washer, for back pad ..........................................................1970-76 9 SIC.501.390.00 ............. Toe board hold down bracket .....................................................................................1970-76 10 SIC.803.914.P ............... Seat belt set, aftermarket, uses factory mounting ......................................................1972-76

1 2

3

4

5

6 7 8 9

10

Reno 1-800-438-8119

914

[ 35 ]

Electrical

Electrical

1 914.610.113.13.SIC ....... Relay board cover, early ......................................................................... 914/914-6 1970-72 914.610.113.13.L ........... Relay board cover, late .......................................................................................914 1973-76 2 914.612.315.10.SIC ...... Fuse box with cover ............................................................................................914 1970-763 SIC.615.109.01 ............. Multi function 5-pin black relay ..................................................................................... 914 all 911.615.109.01 .............. Multi function 5-pin black relay ..................................................................................... 914 all 911.615.108.01 .............. Multi function 5-pin red relay ........................................................................................ 914 all4 1H0.953.227 .................. Turn signal relay ........................................................................................................... 914 all5 914.613.541.02 ............. Back up light switch ..................................................................................................... 914 all 6 901.641.632.00 ............. Oil temperature sender ..................................................................................................914-6 7 901.613.115.00 .............. Two pole warning light switch .......................................................................914-6, 914 to 73 8 901.603.206.02 ............. Voltage regulator ............................................................................................................914-6 9 999.611.919.20 .............. Ground strap at transmission ....................................................................................... 914 all 000.611.902.20 .............. Ground strap battery to body ....................................................................................... 914 all 10 968.613.601.00 ............. Switch for door interior light and handbrake warning light ........................................... 914 all 11 901.613.115.00 .............. Two pole brake warning light switch ............................................................................ 914 all 914.613.116.00 .............. Single pole brake warning light switch ......................................................................... 914 all 12 901.604.102.DX ............ Bosch remanufactured starter, your core required ....................................................... 914 all 13 022.903.023.X ............... Alternator remanufactured, your core required ............................................................ 914 all 14 999.611.065.20 .............. Battery .......................................................................................................................... 914 all 15 911.613.411.01 .............. Brake light switch at pedal assembly ........................................................................... 914 all

15 10 5 15 6

8

9

32

4

2

13121

3 4 11

14

914

1-800-342-1414 [ 36 ]

Wiper ComponentsElectrical

914 6/4 Windshield Wiper Parts

1 964.628.901.02 ............. Wiper blade, black, 13 inch .......................................................................................... 914 all2 895.955.429.A ............... Wiper blade insert, 21 inch, trim to fit ........................................................................... 914 all 3 914.628.313.10.SIC ...... Wiper arm, black, left ................................................................................................... 914 all 914.628.313.10.SET ..... Wiper arms, black, set ................................................................................................. 914 all4 914.628.313.11 .............. Wiper arm and blade set, black ................................................................................... 914 all 5 901.628.341.00 ............. Wiper arm cap nut, black, 2 req'd ................................................................................ 914 all 6 803.955.437. ................. Wiper arm spring washer, 8mm x 12mm, 2 req'd......................................................... 914 all 7 901.628.926.00 ............. Wiper arm shaft bezel, 2 req'd ..................................................................................... 914 all 8 901.628.925.00 ............. Wiper shaft hex nut, 2 req'd ......................................................................................... 914 all 9 901.628.922.00 ............. Wiper shaft flange washer, 2 req'd ............................................................................... 914 all 10 901.628.924.00 ............. Wiper shaft grommet, outer, 2 req'd ............................................................................. 914 all 11 901.628.923.01 ............. Wiper shaft grommet, inner, 2 req'd ............................................................................. 914 all 12 901.628.741.20 ............. Windshield washer jet, chrome, 2 req'd, up to mid 1974 ............................................. 914 all 13 914.628.203.11 .............. Windshield washer jet, black, 2 req'd, mid 1974 to 76 ................................................. 914 all 14 PCG.628.901.10 ........... Windshield washer supply tube, clear .......................................................................... 914 all 15 NLA.628.901.10 ............ Windshield washer supply tube, clear .......................................................................... 914 all 16 914.628.741.00 ............. Rubber bushing for washer pump mount .......................................................................914-6 17 914.628.215.00 ............. Windshield washer check valve ................................................................................... 914 all

12 13 14 15 16 17

914

[ 37 ]

Exterior Lighting

Electrical

Lights

1 914.631.929.11.SIC ....... Left rear tail light lens, USA .......................................................................................... 914 all 914.631.940.11.SIC ....... Right rear tail light lens, USA ....................................................................................... 914 all SIC.631.400 .................. Rear turn signal housing seal, pair .............................................................................. 914 all 914.631.949.10.SIC ...... Left rear tail light lens, Euro ......................................................................................... 914 all 914.631.950.10.SIC ...... Right rear tail light lens, Euro ....................................................................................... 914 all 2 914.631.934.11 .............. Front turn signal lens, amber, USA, Porsche Classic part ........................................... 914 all 914.631.934.11.SIC ....... Front turn signal lens, amber, USA .............................................................................. 914 all 914.631.937.10.SIC ...... Front turn signal lens, amber/white, Euro .................................................................... 914 all 3 914.631.957.10.SIC ...... Front turn signal gasket seal, 2 req'd ........................................................................... 914 all 4 SIC.631.217.10 ............. Front turn signal, wire loom boot, 2 req'd ..................................................................... 914 all 5 914.631.601.00 ............. License plate light, 2 req'd ..................................................................................914 1970-74 6 911.631.620.04 .............. License plate light, 2 req'd ..................................................................................914 1975-76 7 911.631.608.01 .............. License light seal ................................................................................................914 1975-76 8 911.632.012.00 .............. Fasten Seat Belt light ................................................................................................... 914 all 9 901.631.601.01 ............. Luggage boot lamp, rear .............................................................................................. 914 all 10 914.632.107.00 ............. Heat lever light button .........................................................................................914 1973-76 914.631.913.11.SIC ....... Fog lamp lens, 2 req'd, clear ...............................................................................914 1970-74 914.631.923.10.SIC ...... Fog light lens gasket, 2 req'd ..............................................................................914 1970-74 11 914.631.945.00.SIC ...... Side marker light lens, left ............................................................................................ 914 all 914.631.946.00.SIC ...... Side marker light lens, right ......................................................................................... 914 all 12 914.631.939.11.SIC ....... Side marker light assembly, left ................................................................................... 914 all 914.631.940.11.SIC ....... Side marker light assembly, right ................................................................................. 914 all

Bulbs

900.631.102.90 ............. Bulb dash lamp, 12V 2 watt ......................................................................................... 914 all N.017.717.2 ................... Bulb 12V 4 watt ............................................................................................................ 914 all SIC.900.003.05 ............. Halogen Bulb 12V 55 watt, H3 for fog light .........................................................914 1970-74 999.631.108.90 ............. Sealed beam 7 inch, 12volt, 60/40 watt ....................................................................... 914 all 644.631.106.31 ............. SMD, 7 inch H4, set ..................................................................................................... 914 all

12

9114

1

6

7

10

8

5

914

1-800-342-1414 [ 38 ]

ToolsB

ookTechnical SpecbookWKD.422.221

The best source for technical specifications in a pocket sized mini-manual. Made by Porsche for a quick mechanics reference, has dimentions, torque specifications, machining tolerences and model data.

Hinge Pin Tool000.721.290.00

Factory hinge pin removal tool, designed to remove or install door hinge pin without damaging surrounding paint or bodywork, requires part 000.721.290.10.

Hinge Pin Adapter Tool000.721.290.10

Hinge pin adapter tool for use with Factory slide hammer tool to remove and install hinge pin properly.

Long Allen Socket Wrench000.721.119.00

The correct Factory tool for removal and installation of 914-6 heat exchangers using proper heat exchanger nuts (999.085.001.02).

Camshaft Holding Tool000.721.919-10

The correct Factory tool for holding camshaft on 914-6 for servicing.

Ball Joint Removal Tool

000.721.280.20

The correct Factory tool for removal and installation of ball joints on all 914.

Exhaust Valve Tool

T36.180.700

Specialty tool allows the replacement of broken exhaust valve springs without engine disassembly, for 914-6 only.

Piston Ring Compressor

T52.157.825

Piston ring compressor tool for all 914-4 and 914-6

Reno 1-800-438-8119

914

[ 39 ]

Book

Tools

Front Floor Pan Frame JigT52.863

This is an exact re-creation of the Factory tool P-863, and is the only proper way to assure correct placement of the front suspension mounting points for all 914/911/912.

Drive Gear ToolT55.310.000

Toothed synchro hub removal tool, for first and second gear, all 901 transmissions.

Synchro ToolT55.310.001

Synchro engagement tool, for all 901 transmissions.

Canshaft Holding ToolT52.287.017

Camshaft holder / holding tool for 914-6 only.

Door Gap Tool

T52.GAP

A re-creation of Factory gap tool P-1000 in a nylon composite

Clutch Alignment Tool

SIC.116.006.60

The correct tool for instalation of clutch components in proper alignment.

Chain Tensioner Tool

T36.180.214

Specialty tool for chain tensioner installation, 914-6 only.

Spark Plug Wrench

477.012.203

Spark plug wrench fits in factory tool bag for 914-6.

914

1-800-342-1414 [ 40 ]

Chem

icalsChemicals

Porsche Factory Shop Towels (set of 5)NLA.721.915.00.SET

These are genuine original German shop towels, as used in the Porsche Factory Originally one was provided in each accessory Travel Kit, and thus they are highly desirable for concours events. An authentic “touch of class” for your home workshop.

Never-Seez LubricantNLA.043.008.00

Until experienced, the benefits of this special lubricant are seldom fully appreciated. A smear during assembly on an exhaust system bolt or engine exhaust port stud positively ensures easy removal. The best alloy-to-ferrous lubricant available, specially useful on wheel stud to alloy lug nut. Withstands heat up to 2000 degrees F, galling and corrosion. 12.5 ounce aerosol can.

Rost Off Penetrating OilNLA.043.035.00

Special formulation guarantees excellent creep properties and quick rust penetration. Organomolybdenum additives provide the best lubricating properties by smoothing the metal surface. Excellent water displacing properties, long lasting rust protection, silicone free.

Wurth HHS-K Synthetic LubricantNLA.043.007.00

Medium viscous, high pressure resistant synthetic oil that reduces friction, heat, noise or wear between moving parts. Excellent capillary action on initial application, which allows product to penetrate the tightest of gaps, solvent will evaporate leaving a highly adhesive, waterproof load bearing oil. Free from silicone, resin and acid.

Wurth Contact Cleaner OLNLA.043.027.00

This contact cleaner contains additives to improve cleaning and moisture displacement. Use Contact Cleaner OL for the removal of dirt, moisture, dust, flux or oxides from the internal components and contacts of electrical devices. Perfect for radios, switches and automotive electrical devices, leaves an anti-oxidation film behind. 5.5 ounce aerosol can.

Fuel FreshSIC.999.383.54 (32 oz. bottle)

A gasoline preservative and stabilizer. Protect your stored Porsche (or any 2 or 4 cycle engine) with a treatment of Fuel Fresh. Fuel Fresh inhibits the formation of gums, varnishes and corrosion in fuel systems during periods of inactivity. Fuel Fresh eliminates storage problems associated with today's lower octane gasolines. The addition of one ounce of Fuel Fresh per gallon will provide protection up to 24 months. Accurate measurement is easy with the new patented squeeze and pour design.

914

[ 41 ]

Chemicals

Chem

icals

Wurth Rubber GlueSIC.999.130.50

For bonding rubber components to polished, primed or painted metals, wood, various plastics. Excellent for door weatherstrip installation. 6.3 ounce brush top can.

Wurth Rubber CareSIC.999.160.00

Wurth rubber care is a non silicone treatment that cleans and conditions rubber, plastic and vinyl, leaving a soft luster behind. cleaning and preserving such as door, trunk and hood seals, rubber floormats, pedal rubbers, etc. Not agressive to paint or plated parts. 12 ounce aerosol.

Wurth Cockpit CareSIC.999.170.00

Wurth Cockpit Care cleans and protects all hard interior surfaces, plastic, vinyl and trim. Contains no silicone and is anti-static. It will also safely remove wax residue from rubber and vinyl interior or exterior. 16.9 ounce pump spray.

Wurth PTFE Dry LubricantNLA.043.028.00

Does not contain silicone, transparent, non-contaminating lubricant for metal, plastic and rubber. withstands small to medium loads. Resists water, gasoline, oil and weak acids. 10.14 ounces in an aerosol.

Silicone Lubricating CompoundNLA.043.037.00

Wurth Silicone Lubricating Compound works to condition window channels, rubber gaskets, weather stripping, speedometer cables, trunk seals etc. 8 ounce squeeze tube.

Hylomar M Gasket CompoundNLA.043.009.00

Originally developed by Rolls Royce for use in aircraft engines, Hylomar M is a non-hardening gasket material suitable for applications that require exceptional resistance to oil, gasoline, heat and automotive chemicals. Designed specifically for metal to metal sealing, thread sealing and for se with gasket materials. 2.7 ounce tube.

Brushable Seam SealerNLA.043.012.00

Wurth Brushable Seam Sealer is designed specifically for Automotive use, brushable and can be used cracks and body seams on either bare or primed metal. It has excellent adhesion (wet or dry) and permanently flexiable. Will not crack,shrink, harden or sag. Paintable after a 4 to 8 hour cure. 32 ounce can.

914

1-800-342-1414 [ 42 ]

ChemicalsC

hemicals

Wurth Schutz GunNLA.043.003.00Specially designed Wurth Underbody Sealant Schutz Gun allows user to duplicate Factory texture and thickness when repairing or replacing OE installed materials. Treads directly on to Wurth Underbody Seal container.

Wurth Underbody SealSIC.999.110.00.700

Wurth Underbody Seal is a rubber and plastic based, paintable undercoating material containing solvent. When applied with the Wurth Schutz Gun Factory like texture and coverage can be achieved. Paintable with solvent based paints after a 6 to 8 houre cure, priming is necessary. Can be ground after curing. 33.8 ounce can.

Wurth SKS Stoneguard BlackSIC.999.100.00.700

Wurth SKS Stoneguard is suitable for, wheel wells, inside of door pannels or fenders and underbody of vehicle. Proper application with Wurth Schutz Gun insures texture and thickness will match factory coating. Can be painted over after appropriate cure time of 36 to 48 hours. Cured product must be primed to accept final topcoat. Water based. 33.8 ounce bottle.

Wurth Stone Guard BlackSIC.999.120.50

Does not contain silicone, transparent, non-contaminating lubricant for metal, plastic and rubber. withstands small to medium loads. Resists water, gasoline, oil and weak acids. 10.14 ounces in an aerosol.

Silicone Lubricating CompoundNLA.043.037.00

Wurth Silicone Lubricating Compound works to condition window channels, rubber gaskets, weather stripping, speedometer cables, trunk seals etc. 8 ounce squeeze tube.

Wurth High-Build UndersealNLA.043.001.00

Fast drying rubberized spray undercoating, provides lasting protection to automotive underbody, fenders, wheel wells against flying stones also provides sound deadening. This product contains compounds that may cause dificulty with paint adhesion. 17.8 ounce aerosol.

Wurth Weld Thru PrimerSIC.999.155.00

Wurth Zinc Rich Weld Thru Primer protects steel from corrosion by sacrifical or galvanic action. When applied to metal surfaces prior to MIG or spot welding, the zinc melts and fuses to the surface of the steel. Highly resistant to salt water. 13.5 ounce aerosol.

Reno 1-800-438-8119

914

[ 43 ]

Chemicals

Wurth Flexi-Trim Satin Black PaintNLA.095.053.00

Satin finish, equivalent to factory blacked out trim, refinishes steel, aluminum and plastic, correct gloss for wipers and window trim. 15 ounce aerosol.

Wurth Silver Wheel PaintSIC.999.150.10

Wurth Silver Wheel Paint is an acrylic laquer that dries quickly, matches the silver satin finish used by the Factory, it can be clear coated for a full gloss finish. 12 ounce aerosol.

Wurth Matt Black PaintNLA.095.052.00

Wurth Black Laquer Paint is an acrylic laquer that dries quickly, matches the semi matt finish used by the Factory, on wiper arms and trim. 12 ounce aerosol.

Wurth Satin Dark Gray LaquerNLA.095.054.00

Wurth Satin Gray Paint is an acrylic laquer that dries quickly, to a consistant satin gloss finish. 12 ounce aerosol.

Wurth Gloss Clear Laquer PaintNLA.095.051.00

Wurth Gloss Clear Laquer Paint is an acrylic laquer that dries quickly, matches the gloss finish used by the Factory, can be used over silver wheel paint for a full gloss laquer finish. 13.3 ounce aerosol

Wurth Hi-Temp Adhesive SprayNLA.043.005.01

Bonds to metal, wood or plastic a contact adhesive designed for bonding vinyl tops, heavyweight headliners and hood silence pads, where high strength and heat resistance are needed. Bonding time range is 5 minutes to 1 hour. 13 ounce aerosol.

Super 77 Spray AdhesiveNLA.556.010.00

3M Super 77 Multipurpose Adhesive, great for the instalation of carpet, insulation and interior trim. Easy to cover large areas quickly, cleans up up easily with mineral spirits. 24 ounce aerosol.

Chem

icals

914

1-800-342-1414 [ 44 ]

W

Codes

W = 4 cyl. 80 HP

EA = 4 cyl. 80 HP

EB = 4 cyl. 72 HP - Calif

GA = 4 cyl. 95 HP

EC = 4 cyl. 76 HP

MPC

( manifold

pressure

controled)

AFC (air flow

controled)

Engine Number Codes

Consecutive Running Number

0.000.001

1439508WW 5XXD 9

WW = the week of a given calender year

D = the day of the week of the calendar year ( Monday = 1 )

9 = the code for the Karmann Factory at Osnabrueck where all 914 chassis were fabricated.

5XX = the consecutive chassis number, beginning with number 500 each day for 1974 Porsche 914 cars.

Body Build NumberingB

ody Identification

914

[ 45 ]

1970 914/4 76 @ 4900 80 @ 4900 470 29 00001- W 0 000 001- 914/11 HAO 000 001- 470 29 13312 W 0 057 460 HAO 014 826

1971 914/4 76 @ 4900 80 @ 4900 471 29 00001- W 0 057 461- 914/11 HAO 014 827- 471 29 16231 W 0 129 581 HAO 030 093

1972 914/4 76 @ 4900 80 @ 4900 472 29 01400- W 0 129 582 914/11 HAO 030 094- 472 29 21580 W 0 250 000 HAO 053 072 EA 0000 001- EA 0057 000

1973 914 1.7 76 @ 4900 80 @ 5000 473 29 00001- EA 0057 001- 914/12 HAO 053 072- 473 29 27660 EA 0098 793 HAO 056 632

1973 914 1.7 69 @ 4900 72 @ 5000 EB 0000 001- 914/12 HA 01 10 2- Calif. EB 0009 703 HA 31 12 2

1973 914 2.0 91 @ 4900 95 @ 4900 GA 0000 001- 914/12 HA 01 01 3- GA 0006 765 HA 31 07 3

1974 914 1.8 73 @ 4800 76 @ 4800 474 29 00001 EC 0000 001- 914/12 HA 01 08 3- 474 29 21379 EC 0037 551 HA 31 12 2

1974 914 2.0 91 @ 4900 95 @ 4900 GA 0006 766 914.12 HA 01 01 4- GA 0015 021 HA 31 07 4

1975 914 1.8 73 @ 4900 76 @ 4900 475 29 00001- EC 0037 552- 914/12 HA 05 08 4- 475 29 11369 EC 0045 072

1975 914 2.0 84 @ 4900 88 @ 4900 GC 0000 001- 914/12 GC 0002 914

1976 914 2.0 84 @ 4900 88 @ 4900 476 29 00001- GC 0002 915- 914/12 HA 05 08 5- 476 29 04100 GC 0006 946

Year Model HP SAE HP DIN Chassis VIN Engine VIN Trans VIN

Year Model HP DIN Chassis VIN Engine VIN Trans VIN

1970 914/6 110 @ 5800 914 043 0011- 901/36 6400001- 914/01 750 0001- 5 speed 914 043 2668 901/36 6400889 914/05 780 0001- Sportomatic 901/37 6403001- 901/37 6404000 901/38 6404001- 901/38 6405781 901/39 6407001- 901/39 6408000


1972 914/6 110 @ 5800 914 243 0011 901/38 642 0001 914/01 752 0001- 5 Speed 914 243 0260

1972 916 190 @ 6500 914 233 0011 901/38 923/38 5 Speed 914 233 0020

914-6

914-4

Chassis Identification Numbers

Identification Chart

914

1-800-342-1414 [ 46 ]



1972 914/6 110 @ 5800 914 243 0011 901/38 642 0001 914/01 752 0001- 5 Speed 914 243 0260

1972 916 190 @ 6500 914 233 0011 901/38 923/38 5 Speed 914 233 0020

Shipping & DeliveryShipment for orders will be made via the most economical and expeditious means, unless special instructions are received. For U.S. and Canada delivery, UPS or Truck Freight are most commonly used. Truck shipments are generally made freight prepaid on a credit card. Crating charges may be added onto fragile or odd shaped items.All overseas orders are sent via air freight, UPS International, or U.S. Mail depending on size. Air freight orders are sent freight prepaid. UPS orders are prepaid. U.S. Mail orders must be prepaid. Please specify preferred method.

Damage Claims:The responsibility for safe delivery rests with the carrier after the order has been accepted from us for shipment. Should your shipment appear to be damaged or opened when received, check the contents in the presence of the carrier’s agent. Open package immediately and report any discrepancies to the carrier at that time. Shipping damage claims are only good for 5 days from receipt of package. Inspect all parts for condition and note any parts discrepancies with invoice.

Privacy & SecurityYour privacy is very important to us, and we take very seriously the job of protecting your personal privacy. The information that we collect from you will be used solely to process your order and improve your overall shopping experience. We will enter your email address into our system so we can send you newsletters and other offers related to Stoddard NLA. You will have the option of opting out of these offers at any time.

Returns & ReplacementsIf you have a part that appears defective or is not the part that was ordered, please call to discuss the matter, or obtain a return authorization. Returns over 6 months old are elligible for Stoddard Store credit only. Parts over 12 months are not returnable. Returns must be sent prepaid and you must include your invoices. We will charge a 20% handling fee on all returns unless the merchandise is defective or was shipped in error.

The following terms of warranty apply to all Parts and Accessories sold by Stoddard NLA-LLC.

SIC warrants that every new and remanufactured part and accessory sold to a customer will be free from defects in material and workmanship under normal use and service for 12 months/unlimited mileage from date of sale of the part or accessory to the original customer.

Items Covered: Any part or accessory sold by SIC that is determined by SIC to be defective will be either repaired or replaced with a new or remanufactured part. The labor required to remove, repair or replace the defective part or accessory is not reimbursable.

Items Not Covered: Damages due to accidents, misuse or negligence. Parts damaged due to misuse, neglect, improper maintenance, alteration, accidents, or fire, or which have been improperly installed, or used in applications for which they were not designed.

Parts or accessories made out of cloth or leather (upholstery, convertible tops), wood, paint, or chrome which have been affected by environmental conditions, including, but not limited to, airborne fallout, chemicals, tree sap, road salt, hail, windstorms and other environmental factors.

Damage to Glass. Glass breakage or scratches are not covered unless physical proof of a manufacturing fault can be established.

Use of the parts or accessory in competitive events.

Any loss or damage caused by installation of an incorrect part. While SIC has made every effort to ensure that the information in this catalog is complete and accurate, please call us before attempting to install a part that you suspect is incorrect for the application.

Throughout the catalog there are notes that give technical suggestions; Stoddard NLA-LLC is not responsible for any consequential or incidental damages pertaining to these suggestions. Some prior automotive experience on your part is assumed. When in doubt, or if you have any questions, please call us first.

Ordering Policy

Reno 1-800-438-8119

914

[ 47 ]

To Obtain Warranty Repair or Replacement: Present SIC with a copy of your original sales receipt, name, mailing address, phone number, date purchased and mileage installed, date and mileage of failure, VIN, and description of problem. Please arrange return before sending parts.

Warranty Period: The warranty period begins on the date of sale of the part to the customer.

No Other Warranties Made: This warranty is in lieu of all other expressed warranties of SIC or any distributor of SIC parts. Any implied warranty is limited in duration to the duration of this warranty. SIC does not assume or authorize any person to assume on our behalf any other obligation or liability.

Consequential Damage Excluded: SIC is not responsible for loss of time, inconvenience, loss of use of the vehicle, towing expense or other incidental or consequential damage.

Ordering

To Expedite Your Order:Have model, year and chassis or engine number, where applicable, available when placing your order.

Double-check your part numbers and application.Have your customer number available when placing either phone or mail order. If you have not received a customer number prior to placing the order, we will ask you for your complete mailing address/shipping address, telephone number and Email address for our records.

Our professional staff can usually edit part number errors, but the responsibility for correct number and application rests with the customer.

Payment, Pricing & PromotionsOur prices reflect the quality of merchandise our customers demand. We believe in competitive pricing but quality is never compromised to offer lowest prices.

All prices are subject to change without notice. Invoices will be based on current prices at the time the order is shipped. We will gladly verify current prices by phone or fax/email. In case of a pricing issue, Stoddard adheres to the “Unilateral mistake of fact doctrine,’ whereby the company can cancel orders and refund customers money because of pricing errors, or any other reason, i.e., part in question would normally sell in the $1000.00 range, and customer paid $100.00.

Payment Methods:We accept Visa, MasterCard, Discover and American Express credit cards, money orders, and certified checks. We accept personal checks, we do not ship C.O.D. Your credit card account will be charged at the time of shipping for only those items shipped.

Warranty

914

1-800-342-1414 [ 48 ]

Stoddard 2018 Swap Meet T-ShirtSIC.SWAP.18

Another classic design by Nicolas Hunzlker features a 1974 914 in European specification (without the charming bumperetts and side marker lights), black bumpers with optional light weight Mahle alloy wheels. Avaliable in S, M, L, XL and XXL.

leather Porsche Crest Key RingWAP.050.097.OH Gray WAP.050.095.OE Blue WAP.050.090.OE Black

Factory Key Ring, Leather with full color crest.

Stoddard Authentic 914-6GT ShirtBOH.611.00

Every 914 enthusiast wants a real M-471 914-6 GT, only 10 were built by Porsche and most led a racecar's life... hard and fast. This Nicolas Hunziker designed beauty might be the least expensive way to own one. Avaliable in S, M, L, XL and XXL.

Oil Travel BagPNA.000.100.0D

This Porsche Factory Oil Travel Bag makes it easy to carry an extra quart or liter of motor oil, it has a velcro back to secure it to carpeted areas in the trunk . It includes a disposable funnel and wipe for easy use.

Porsche Crest Polo

WAP.592.00

Black Porsche Crest Polo with full color embroidered crest. Avaliable in S, M and L.

Genuine Parts Sign

SIC.SIGN

Imported from Europe, measures 400mm X 590mm, heavy enameled steel, finished corners, as original. The perfect addition to your shop or garage.

Porsche Friend Decal

NLA.040.00

Started as an inclusion to the catalog in the late 70's the Porsche Friend decal has been the perfect addition to your daily driver or support vehicle for over 40 years.

914 Models from Spark and Schuco

When avaliable we stock 914 molels check online for availability.

Boutique and ApparelB

ody Identification

914

[ 49 ]

Notes:

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

914

1-800-342-1414 [ 50 ]

Notes:

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

914

[ 51 ]

Notes:

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

___________________________________________________________________________________________________

__________________________________________________________________________________________________

___________________________________________________________________________________________________

The Porsche Experts - Since 1957- Stoddard NLA-LLC More Authentic parts at: stoddard.com

Highland Heights, Ohio 44143 USA 800 342 1414 Reno, Nevada 89431 USA 800 438 8119

Ashtray with Mounting Plate Stoddard Exclusive Production 356A, 356B & 356C NLA-552-061-01

Headlight Stone GuardsFor 356 and Early 911 NLA-62-114

Interior LightOur Exclusive Production For 356C, 911 and 912 SIC-632-101-00

Gas TanksFor 356B T6 and 356C Proper Grey Finish NLA-201-001-07

Engine Sheetmetal356 Rear Horizontal Tin shown 546-06-562

Gasket Sets356 Transmission Set shown 741-300-111-00

Quarter Window LatchesFor 356 or 911 644-543-041-00 shown

Insulation KitsCockpit or Engine Bay For 356, 911 and 912 NLA-556-552-00 Late 356 shown

Borrani Turbo SprintBi-Metallic with Hubs and Knock-Offs For 356A, 356B and 356C

Hub CapsFor Drum or Disc Wheels Fits 356, 911 and 912 SIC-361-031-01 shown

Seat Recliner Cover Set For Early 911 and 912 901-521-915-01-700-SET

911 Floor PansFor Early 911 912 Correct StampingSIC-501-051-31-2

Pirelli Classic TiresPorsche N-SpecCN36 and P7165/80R15 CN36 shown

Maxilite Wheels Many Sizes, Offsets and Finishes15x7 23mm offset shown

New 356 Intake PlenumPerfect Recreation for Late 356 644-571-012-06

Nose PanelsOur USA production, includes fog light bracket, NLA-503-011-04 RightNLA-503-011-03 Left 356B T5 Shown

Exclusive Pre-A Sheetmetal Dozens of New Parts356-51-257 Rear Bulkhead shown

Disc Brake WheelsFrom Factory ToolingMade in USAChrome or Silver 15x4.5 15x5.5 15x6-inch

Complete 356 Floor Pan Kits NLA-501-050-03 356B & 356C shown

Outer Frame Repair SkinRepairs 911 912 Wheelhouse Including Torsion Tube and Jack Receiver Area SIC-501-963-01 SIC-501-964-01

20SAVE

%

VISIT STODDARD.COM FOR OUR FEATURED PRODUCT SPECIAL THIS MONTH

Stoddard_Montage_January 2019_Ad.indd 1 1/11/19 6:33 PM

Stoddard NLA-LLCHighland Heights, Ohio 44143 USA 800-342-1414

Reno, Nevada 89502 USA 800-438-8119

www.stoddard.com

For the latest additions and current pricing go to our web site with over 10,000 NOS, original Porsche Classic

and Stoddard Authentic Parts all on line.

Documents

$5 - Stoddard · Table of Contents 1-800-342-1414 1 - 7 Engine Crankshaft Parts, Engine Lubrication, Engine Sheet Metal, Pistons, Rings, Cylinders, and Valve Train. 8 - 9 Fuel System